[PATCH v8 0/3] Adding the Sparx5 Switch Reset Driver

[PATCH v8 0/3] Adding the Sparx5 Switch Reset Driver

[Steen Hegelund]

This series provides the Microchip Sparx5 Switch Reset Driver

The Sparx5 Switch SoC has a number of components that can be reset
individually, but at least the Switch Core needs to be in a well defined
state at power on, when any of the Sparx5 drivers starts to access the
Switch Core, this reset driver is available.

The reset driver is loaded early via the postcore_initcall interface, and
will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
that are loaded next, and the first of them to be loaded can perform the
one-time Switch Core reset that is needed.

The driver has protection so that the system busses, DDR controller, PCI-E
and ARM A53 CPU and a few other subsystems are not touched by the reset.

Sparx5 will no longer use the existing Ocelot chip reset driver, but use
this new switch reset driver as it has the reset controller interface that
allows the first client to perform the reset on behalf of all the Sparx5
component drivers.

The Sparx5 Chip Register Model can be browsed at this location:
https://github.com/microchip-ung/sparx-5_reginfo
and the datasheet is available here:
https://ww1.microchip.com/downloads/en/DeviceDoc/SparX-5_Family_L2L3_Enterprise_10G_Ethernet_Switches_Datasheet_00003822B.pdf

History:

v7 -> v8 Updated the commit descriptions to explain the change from using
         the existing Ocelot chip reset driver to use a new switch reset
         driver.

v6 -> v7 Use devm_platform_get_and_ioremap_resource to get the IO range.
         Rebase on v5.12-rc1

v5 -> v6 Using the existing CPU syscon for reset protection and add a small
         IO range for the GCB Reset Register.

v4 -> v5 Changed the two syscons into IO ranges and updated the bindings to
         reflect this change.

v3 -> v4 Added commit message descriptions

v2 -> v3 Removed unused headers
         Renamed the reset controller dev member.
         Use regmap_read_poll_timeout instead of polling a function.
         Used two separate syscon entries in the binding
         Simplified the syscon error handling.
         Simplified the devm_reset_controller_register error handling.
         Moved the contents of the mchp_sparx5_reset_config function into
         the probe function.

v1 -> v2 Removed debug prints
         Changed the error handling to save the error code before jumping.

Steen Hegelund (3):
  dt-bindings: reset: microchip sparx5 reset driver bindings
  reset: mchp: sparx5: add switch reset driver
  arm64: dts: reset: add microchip sparx5 switch reset driver

 .../bindings/reset/microchip,rst.yaml         |  58 +++++++
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |   7 +-
 drivers/reset/Kconfig                         |   8 +
 drivers/reset/Makefile                        |   1 +
 drivers/reset/reset-microchip-sparx5.c        | 146 ++++++++++++++++++
 5 files changed, 218 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
 create mode 100644 drivers/reset/reset-microchip-sparx5.c

-- 
2.30.2

[PATCH v8 0/3] Adding the Sparx5 Switch Reset Driver

[Steen Hegelund]

This series provides the Microchip Sparx5 Switch Reset Driver

The Sparx5 Switch SoC has a number of components that can be reset
individually, but at least the Switch Core needs to be in a well defined
state at power on, when any of the Sparx5 drivers starts to access the
Switch Core, this reset driver is available.

The reset driver is loaded early via the postcore_initcall interface, and
will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
that are loaded next, and the first of them to be loaded can perform the
one-time Switch Core reset that is needed.

The driver has protection so that the system busses, DDR controller, PCI-E
and ARM A53 CPU and a few other subsystems are not touched by the reset.

Sparx5 will no longer use the existing Ocelot chip reset driver, but use
this new switch reset driver as it has the reset controller interface that
allows the first client to perform the reset on behalf of all the Sparx5
component drivers.

The Sparx5 Chip Register Model can be browsed at this location:
https://github.com/microchip-ung/sparx-5_reginfo
and the datasheet is available here:
https://ww1.microchip.com/downloads/en/DeviceDoc/SparX-5_Family_L2L3_Enterprise_10G_Ethernet_Switches_Datasheet_00003822B.pdf

History:

v7 -> v8 Updated the commit descriptions to explain the change from using
         the existing Ocelot chip reset driver to use a new switch reset
         driver.

v6 -> v7 Use devm_platform_get_and_ioremap_resource to get the IO range.
         Rebase on v5.12-rc1

v5 -> v6 Using the existing CPU syscon for reset protection and add a small
         IO range for the GCB Reset Register.

v4 -> v5 Changed the two syscons into IO ranges and updated the bindings to
         reflect this change.

v3 -> v4 Added commit message descriptions

v2 -> v3 Removed unused headers
         Renamed the reset controller dev member.
         Use regmap_read_poll_timeout instead of polling a function.
         Used two separate syscon entries in the binding
         Simplified the syscon error handling.
         Simplified the devm_reset_controller_register error handling.
         Moved the contents of the mchp_sparx5_reset_config function into
         the probe function.

v1 -> v2 Removed debug prints
         Changed the error handling to save the error code before jumping.

Steen Hegelund (3):
  dt-bindings: reset: microchip sparx5 reset driver bindings
  reset: mchp: sparx5: add switch reset driver
  arm64: dts: reset: add microchip sparx5 switch reset driver

 .../bindings/reset/microchip,rst.yaml         |  58 +++++++
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |   7 +-
 drivers/reset/Kconfig                         |   8 +
 drivers/reset/Makefile                        |   1 +
 drivers/reset/reset-microchip-sparx5.c        | 146 ++++++++++++++++++
 5 files changed, 218 insertions(+), 2 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
 create mode 100644 drivers/reset/reset-microchip-sparx5.c

-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 1/3] dt-bindings: reset: microchip sparx5 reset driver bindings

[Steen Hegelund]

Document the Sparx5 reset device driver bindings

The driver uses a syscon and an IO range on sparx5 for access to
the reset control and the reset status.

Sparx5 will no longer use the existing Ocelot chip reset driver, but use
this new switch reset driver as it has the reset controller interface that
allows the first client to perform the reset on behalf of all the Sparx5
component drivers.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
---
 .../bindings/reset/microchip,rst.yaml         | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml

diff --git a/Documentation/devicetree/bindings/reset/microchip,rst.yaml b/Documentation/devicetree/bindings/reset/microchip,rst.yaml
new file mode 100644
index 000000000000..370579aeeca1
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/microchip,rst.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/reset/microchip,rst.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Microchip Sparx5 Switch Reset Controller
+
+maintainers:
+  - Steen Hegelund <steen.hegelund@microchip.com>
+  - Lars Povlsen <lars.povlsen@microchip.com>
+
+description: |
+  The Microchip Sparx5 Switch provides reset control and implements the following
+  functions
+    - One Time Switch Core Reset (Soft Reset)
+
+properties:
+  $nodename:
+    pattern: "^reset-controller@[0-9a-f]+$"
+
+  compatible:
+    const: microchip,sparx5-switch-reset
+
+  reg:
+    items:
+      - description: global control block registers
+
+  reg-names:
+    items:
+      - const: gcb
+
+  "#reset-cells":
+    const: 1
+
+  cpu-syscon:
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+    description: syscon used to access CPU reset
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - "#reset-cells"
+  - cpu-syscon
+
+additionalProperties: false
+
+examples:
+  - |
+    reset: reset-controller@11010008 {
+        compatible = "microchip,sparx5-switch-reset";
+        reg = <0x11010008 0x4>;
+        reg-names = "gcb";
+        #reset-cells = <1>;
+        cpu-syscon = <&cpu_ctrl>;
+    };
+
-- 
2.30.2

[PATCH v8 1/3] dt-bindings: reset: microchip sparx5 reset driver bindings

[Steen Hegelund]

Document the Sparx5 reset device driver bindings

The driver uses a syscon and an IO range on sparx5 for access to
the reset control and the reset status.

Sparx5 will no longer use the existing Ocelot chip reset driver, but use
this new switch reset driver as it has the reset controller interface that
allows the first client to perform the reset on behalf of all the Sparx5
component drivers.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
---
 .../bindings/reset/microchip,rst.yaml         | 58 +++++++++++++++++++
 1 file changed, 58 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml

diff --git a/Documentation/devicetree/bindings/reset/microchip,rst.yaml b/Documentation/devicetree/bindings/reset/microchip,rst.yaml
new file mode 100644
index 000000000000..370579aeeca1
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/microchip,rst.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/reset/microchip,rst.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Microchip Sparx5 Switch Reset Controller
+
+maintainers:
+  - Steen Hegelund <steen.hegelund@microchip.com>
+  - Lars Povlsen <lars.povlsen@microchip.com>
+
+description: |
+  The Microchip Sparx5 Switch provides reset control and implements the following
+  functions
+    - One Time Switch Core Reset (Soft Reset)
+
+properties:
+  $nodename:
+    pattern: "^reset-controller@[0-9a-f]+$"
+
+  compatible:
+    const: microchip,sparx5-switch-reset
+
+  reg:
+    items:
+      - description: global control block registers
+
+  reg-names:
+    items:
+      - const: gcb
+
+  "#reset-cells":
+    const: 1
+
+  cpu-syscon:
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+    description: syscon used to access CPU reset
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - "#reset-cells"
+  - cpu-syscon
+
+additionalProperties: false
+
+examples:
+  - |
+    reset: reset-controller@11010008 {
+        compatible = "microchip,sparx5-switch-reset";
+        reg = <0x11010008 0x4>;
+        reg-names = "gcb";
+        #reset-cells = <1>;
+        cpu-syscon = <&cpu_ctrl>;
+    };
+
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 2/3] reset: mchp: sparx5: add switch reset driver

[Steen Hegelund]

The Sparx5 Switch SoC has a number of components that can be reset
indiviually, but at least the Switch Core needs to be in a well defined
state at power on, when any of the Sparx5 drivers starts to access the
Switch Core, this reset driver is available.

The reset driver is loaded early via the postcore_initcall interface, and
will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
that are loaded next, and the first of them to be loaded can perform the
one-time Switch Core reset that is needed.

The driver has protection so that the system busses, DDR controller, PCI-E
and ARM A53 CPU and a few other subsystems are not touched by the reset.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 drivers/reset/Kconfig                  |   8 ++
 drivers/reset/Makefile                 |   1 +
 drivers/reset/reset-microchip-sparx5.c | 146 +++++++++++++++++++++++++
 3 files changed, 155 insertions(+)
 create mode 100644 drivers/reset/reset-microchip-sparx5.c

diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 4171c6f76385..c26798092ccf 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -111,6 +111,14 @@ config RESET_LPC18XX
 	help
 	  This enables the reset controller driver for NXP LPC18xx/43xx SoCs.
 
+config RESET_MCHP_SPARX5
+	bool "Microchip Sparx5 reset driver"
+	depends on HAS_IOMEM || COMPILE_TEST
+	default y if SPARX5_SWITCH
+	select MFD_SYSCON
+	help
+	  This driver supports switch core reset for the Microchip Sparx5 SoC.
+
 config RESET_MESON
 	tristate "Meson Reset Driver"
 	depends on ARCH_MESON || COMPILE_TEST
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 65a118a91b27..c1d6aa9b1b52 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_RESET_INTEL_GW) += reset-intel-gw.o
 obj-$(CONFIG_RESET_K210) += reset-k210.o
 obj-$(CONFIG_RESET_LANTIQ) += reset-lantiq.o
 obj-$(CONFIG_RESET_LPC18XX) += reset-lpc18xx.o
+obj-$(CONFIG_RESET_MCHP_SPARX5) += reset-microchip-sparx5.o
 obj-$(CONFIG_RESET_MESON) += reset-meson.o
 obj-$(CONFIG_RESET_MESON_AUDIO_ARB) += reset-meson-audio-arb.o
 obj-$(CONFIG_RESET_NPCM) += reset-npcm.o
diff --git a/drivers/reset/reset-microchip-sparx5.c b/drivers/reset/reset-microchip-sparx5.c
new file mode 100644
index 000000000000..cff39a643a14
--- /dev/null
+++ b/drivers/reset/reset-microchip-sparx5.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Microchip Sparx5 Switch Reset driver
+ *
+ * Copyright (c) 2020 Microchip Technology Inc. and its subsidiaries.
+ *
+ * The Sparx5 Chip Register Model can be browsed at this location:
+ * https://github.com/microchip-ung/sparx-5_reginfo
+ */
+#include <linux/mfd/syscon.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset-controller.h>
+
+#define PROTECT_REG    0x84
+#define PROTECT_BIT    BIT(10)
+#define SOFT_RESET_REG 0x00
+#define SOFT_RESET_BIT BIT(1)
+
+struct mchp_reset_context {
+	struct regmap *cpu_ctrl;
+	struct regmap *gcb_ctrl;
+	struct reset_controller_dev rcdev;
+};
+
+static struct regmap_config sparx5_reset_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+};
+
+static int sparx5_switch_reset(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	struct mchp_reset_context *ctx =
+		container_of(rcdev, struct mchp_reset_context, rcdev);
+	u32 val;
+
+	/* Make sure the core is PROTECTED from reset */
+	regmap_update_bits(ctx->cpu_ctrl, PROTECT_REG, PROTECT_BIT, PROTECT_BIT);
+
+	/* Start soft reset */
+	regmap_write(ctx->gcb_ctrl, SOFT_RESET_REG, SOFT_RESET_BIT);
+
+	/* Wait for soft reset done */
+	return regmap_read_poll_timeout(ctx->gcb_ctrl, SOFT_RESET_REG, val,
+					(val & SOFT_RESET_BIT) == 0,
+					1, 100);
+}
+
+static const struct reset_control_ops sparx5_reset_ops = {
+	.reset = sparx5_switch_reset,
+};
+
+static int mchp_sparx5_map_syscon(struct platform_device *pdev, char *name,
+				  struct regmap **target)
+{
+	struct device_node *syscon_np;
+	struct regmap *regmap;
+	int err;
+
+	syscon_np = of_parse_phandle(pdev->dev.of_node, name, 0);
+	if (!syscon_np)
+		return -ENODEV;
+	regmap = syscon_node_to_regmap(syscon_np);
+	of_node_put(syscon_np);
+	if (IS_ERR(regmap)) {
+		err = PTR_ERR(regmap);
+		dev_err(&pdev->dev, "No '%s' map: %d\n", name, err);
+		return err;
+	}
+	*target = regmap;
+	return 0;
+}
+
+static int mchp_sparx5_map_io(struct platform_device *pdev, int index,
+			      struct regmap **target)
+{
+	struct resource *res;
+	struct regmap *map;
+	void __iomem *mem;
+
+	mem = devm_platform_get_and_ioremap_resource(pdev, index, &res);
+	if (!mem) {
+		dev_err(&pdev->dev, "Could not map resource %d\n", index);
+		return -ENXIO;
+	}
+	sparx5_reset_regmap_config.name = res->name;
+	map = devm_regmap_init_mmio(&pdev->dev, mem, &sparx5_reset_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+	*target = map;
+	return 0;
+}
+
+static int mchp_sparx5_reset_probe(struct platform_device *pdev)
+{
+	struct device_node *dn = pdev->dev.of_node;
+	struct mchp_reset_context *ctx;
+	int err;
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	err = mchp_sparx5_map_syscon(pdev, "cpu-syscon", &ctx->cpu_ctrl);
+	if (err)
+		return err;
+	err = mchp_sparx5_map_io(pdev, 0, &ctx->gcb_ctrl);
+	if (err)
+		return err;
+
+	ctx->rcdev.owner = THIS_MODULE;
+	ctx->rcdev.nr_resets = 1;
+	ctx->rcdev.ops = &sparx5_reset_ops;
+	ctx->rcdev.of_node = dn;
+
+	return devm_reset_controller_register(&pdev->dev, &ctx->rcdev);
+}
+
+static const struct of_device_id mchp_sparx5_reset_of_match[] = {
+	{
+		.compatible = "microchip,sparx5-switch-reset",
+	},
+	{ }
+};
+
+static struct platform_driver mchp_sparx5_reset_driver = {
+	.probe = mchp_sparx5_reset_probe,
+	.driver = {
+		.name = "sparx5-switch-reset",
+		.of_match_table = mchp_sparx5_reset_of_match,
+	},
+};
+
+static int __init mchp_sparx5_reset_init(void)
+{
+	return platform_driver_register(&mchp_sparx5_reset_driver);
+}
+
+postcore_initcall(mchp_sparx5_reset_init);
+
+MODULE_DESCRIPTION("Microchip Sparx5 switch reset driver");
+MODULE_AUTHOR("Steen Hegelund <steen.hegelund@microchip.com>");
+MODULE_LICENSE("Dual MIT/GPL");
-- 
2.30.2

[PATCH v8 2/3] reset: mchp: sparx5: add switch reset driver

[Steen Hegelund]

The Sparx5 Switch SoC has a number of components that can be reset
indiviually, but at least the Switch Core needs to be in a well defined
state at power on, when any of the Sparx5 drivers starts to access the
Switch Core, this reset driver is available.

The reset driver is loaded early via the postcore_initcall interface, and
will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
that are loaded next, and the first of them to be loaded can perform the
one-time Switch Core reset that is needed.

The driver has protection so that the system busses, DDR controller, PCI-E
and ARM A53 CPU and a few other subsystems are not touched by the reset.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 drivers/reset/Kconfig                  |   8 ++
 drivers/reset/Makefile                 |   1 +
 drivers/reset/reset-microchip-sparx5.c | 146 +++++++++++++++++++++++++
 3 files changed, 155 insertions(+)
 create mode 100644 drivers/reset/reset-microchip-sparx5.c

diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 4171c6f76385..c26798092ccf 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -111,6 +111,14 @@ config RESET_LPC18XX
 	help
 	  This enables the reset controller driver for NXP LPC18xx/43xx SoCs.
 
+config RESET_MCHP_SPARX5
+	bool "Microchip Sparx5 reset driver"
+	depends on HAS_IOMEM || COMPILE_TEST
+	default y if SPARX5_SWITCH
+	select MFD_SYSCON
+	help
+	  This driver supports switch core reset for the Microchip Sparx5 SoC.
+
 config RESET_MESON
 	tristate "Meson Reset Driver"
 	depends on ARCH_MESON || COMPILE_TEST
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 65a118a91b27..c1d6aa9b1b52 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -16,6 +16,7 @@ obj-$(CONFIG_RESET_INTEL_GW) += reset-intel-gw.o
 obj-$(CONFIG_RESET_K210) += reset-k210.o
 obj-$(CONFIG_RESET_LANTIQ) += reset-lantiq.o
 obj-$(CONFIG_RESET_LPC18XX) += reset-lpc18xx.o
+obj-$(CONFIG_RESET_MCHP_SPARX5) += reset-microchip-sparx5.o
 obj-$(CONFIG_RESET_MESON) += reset-meson.o
 obj-$(CONFIG_RESET_MESON_AUDIO_ARB) += reset-meson-audio-arb.o
 obj-$(CONFIG_RESET_NPCM) += reset-npcm.o
diff --git a/drivers/reset/reset-microchip-sparx5.c b/drivers/reset/reset-microchip-sparx5.c
new file mode 100644
index 000000000000..cff39a643a14
--- /dev/null
+++ b/drivers/reset/reset-microchip-sparx5.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Microchip Sparx5 Switch Reset driver
+ *
+ * Copyright (c) 2020 Microchip Technology Inc. and its subsidiaries.
+ *
+ * The Sparx5 Chip Register Model can be browsed at this location:
+ * https://github.com/microchip-ung/sparx-5_reginfo
+ */
+#include <linux/mfd/syscon.h>
+#include <linux/of_device.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset-controller.h>
+
+#define PROTECT_REG    0x84
+#define PROTECT_BIT    BIT(10)
+#define SOFT_RESET_REG 0x00
+#define SOFT_RESET_BIT BIT(1)
+
+struct mchp_reset_context {
+	struct regmap *cpu_ctrl;
+	struct regmap *gcb_ctrl;
+	struct reset_controller_dev rcdev;
+};
+
+static struct regmap_config sparx5_reset_regmap_config = {
+	.reg_bits	= 32,
+	.val_bits	= 32,
+	.reg_stride	= 4,
+};
+
+static int sparx5_switch_reset(struct reset_controller_dev *rcdev,
+			       unsigned long id)
+{
+	struct mchp_reset_context *ctx =
+		container_of(rcdev, struct mchp_reset_context, rcdev);
+	u32 val;
+
+	/* Make sure the core is PROTECTED from reset */
+	regmap_update_bits(ctx->cpu_ctrl, PROTECT_REG, PROTECT_BIT, PROTECT_BIT);
+
+	/* Start soft reset */
+	regmap_write(ctx->gcb_ctrl, SOFT_RESET_REG, SOFT_RESET_BIT);
+
+	/* Wait for soft reset done */
+	return regmap_read_poll_timeout(ctx->gcb_ctrl, SOFT_RESET_REG, val,
+					(val & SOFT_RESET_BIT) == 0,
+					1, 100);
+}
+
+static const struct reset_control_ops sparx5_reset_ops = {
+	.reset = sparx5_switch_reset,
+};
+
+static int mchp_sparx5_map_syscon(struct platform_device *pdev, char *name,
+				  struct regmap **target)
+{
+	struct device_node *syscon_np;
+	struct regmap *regmap;
+	int err;
+
+	syscon_np = of_parse_phandle(pdev->dev.of_node, name, 0);
+	if (!syscon_np)
+		return -ENODEV;
+	regmap = syscon_node_to_regmap(syscon_np);
+	of_node_put(syscon_np);
+	if (IS_ERR(regmap)) {
+		err = PTR_ERR(regmap);
+		dev_err(&pdev->dev, "No '%s' map: %d\n", name, err);
+		return err;
+	}
+	*target = regmap;
+	return 0;
+}
+
+static int mchp_sparx5_map_io(struct platform_device *pdev, int index,
+			      struct regmap **target)
+{
+	struct resource *res;
+	struct regmap *map;
+	void __iomem *mem;
+
+	mem = devm_platform_get_and_ioremap_resource(pdev, index, &res);
+	if (!mem) {
+		dev_err(&pdev->dev, "Could not map resource %d\n", index);
+		return -ENXIO;
+	}
+	sparx5_reset_regmap_config.name = res->name;
+	map = devm_regmap_init_mmio(&pdev->dev, mem, &sparx5_reset_regmap_config);
+	if (IS_ERR(map))
+		return PTR_ERR(map);
+	*target = map;
+	return 0;
+}
+
+static int mchp_sparx5_reset_probe(struct platform_device *pdev)
+{
+	struct device_node *dn = pdev->dev.of_node;
+	struct mchp_reset_context *ctx;
+	int err;
+
+	ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL);
+	if (!ctx)
+		return -ENOMEM;
+
+	err = mchp_sparx5_map_syscon(pdev, "cpu-syscon", &ctx->cpu_ctrl);
+	if (err)
+		return err;
+	err = mchp_sparx5_map_io(pdev, 0, &ctx->gcb_ctrl);
+	if (err)
+		return err;
+
+	ctx->rcdev.owner = THIS_MODULE;
+	ctx->rcdev.nr_resets = 1;
+	ctx->rcdev.ops = &sparx5_reset_ops;
+	ctx->rcdev.of_node = dn;
+
+	return devm_reset_controller_register(&pdev->dev, &ctx->rcdev);
+}
+
+static const struct of_device_id mchp_sparx5_reset_of_match[] = {
+	{
+		.compatible = "microchip,sparx5-switch-reset",
+	},
+	{ }
+};
+
+static struct platform_driver mchp_sparx5_reset_driver = {
+	.probe = mchp_sparx5_reset_probe,
+	.driver = {
+		.name = "sparx5-switch-reset",
+		.of_match_table = mchp_sparx5_reset_of_match,
+	},
+};
+
+static int __init mchp_sparx5_reset_init(void)
+{
+	return platform_driver_register(&mchp_sparx5_reset_driver);
+}
+
+postcore_initcall(mchp_sparx5_reset_init);
+
+MODULE_DESCRIPTION("Microchip Sparx5 switch reset driver");
+MODULE_AUTHOR("Steen Hegelund <steen.hegelund@microchip.com>");
+MODULE_LICENSE("Dual MIT/GPL");
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v8 3/3] arm64: dts: reset: add microchip sparx5 switch reset driver

[Steen Hegelund]

This provides reset driver support for the Microchip Sparx5 PCB134 and
PCB135 reference boards.

The Sparx5 Switch will no longer use the Ocelot Chip Reset Driver (with the
compatible string "microchip,sparx5-chip-reset"), but use a separate driver
that exposes a reset controller interface and has the compatiple string
"microchip,sparx5-switch-reset".

Eventually the Sparx5 reset support will be removed from the Ocelot chip
reset driver.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 arch/arm64/boot/dts/microchip/sparx5.dtsi | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 380281f312d8..dc3ada5cf9fc 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -132,9 +132,12 @@ mux: mux-controller {
 			};
 		};
 
-		reset@611010008 {
-			compatible = "microchip,sparx5-chip-reset";
+		reset: reset-controller@611010008 {
+			compatible = "microchip,sparx5-switch-reset";
 			reg = <0x6 0x11010008 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
 		};
 
 		uart0: serial@600100000 {
-- 
2.30.2

[PATCH v8 3/3] arm64: dts: reset: add microchip sparx5 switch reset driver

[Steen Hegelund]

This provides reset driver support for the Microchip Sparx5 PCB134 and
PCB135 reference boards.

The Sparx5 Switch will no longer use the Ocelot Chip Reset Driver (with the
compatible string "microchip,sparx5-chip-reset"), but use a separate driver
that exposes a reset controller interface and has the compatiple string
"microchip,sparx5-switch-reset".

Eventually the Sparx5 reset support will be removed from the Ocelot chip
reset driver.

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
---
 arch/arm64/boot/dts/microchip/sparx5.dtsi | 7 +++++--
 1 file changed, 5 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 380281f312d8..dc3ada5cf9fc 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -132,9 +132,12 @@ mux: mux-controller {
 			};
 		};
 
-		reset@611010008 {
-			compatible = "microchip,sparx5-chip-reset";
+		reset: reset-controller@611010008 {
+			compatible = "microchip,sparx5-switch-reset";
 			reg = <0x6 0x11010008 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
 		};
 
 		uart0: serial@600100000 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v8 1/3] dt-bindings: reset: microchip sparx5 reset driver bindings

[Rob Herring]

On Tue, 16 Mar 2021 10:08:37 +0100, Steen Hegelund wrote:
> Document the Sparx5 reset device driver bindings
> 
> The driver uses a syscon and an IO range on sparx5 for access to
> the reset control and the reset status.
> 
> Sparx5 will no longer use the existing Ocelot chip reset driver, but use
> this new switch reset driver as it has the reset controller interface that
> allows the first client to perform the reset on behalf of all the Sparx5
> component drivers.
> 
> Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
> ---
>  .../bindings/reset/microchip,rst.yaml         | 58 +++++++++++++++++++
>  1 file changed, 58 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v8 1/3] dt-bindings: reset: microchip sparx5 reset driver bindings

[Rob Herring]

On Tue, 16 Mar 2021 10:08:37 +0100, Steen Hegelund wrote:
> Document the Sparx5 reset device driver bindings
> 
> The driver uses a syscon and an IO range on sparx5 for access to
> the reset control and the reset status.
> 
> Sparx5 will no longer use the existing Ocelot chip reset driver, but use
> this new switch reset driver as it has the reset controller interface that
> allows the first client to perform the reset on behalf of all the Sparx5
> component drivers.
> 
> Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
> ---
>  .../bindings/reset/microchip,rst.yaml         | 58 +++++++++++++++++++
>  1 file changed, 58 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v8 0/3] Adding the Sparx5 Switch Reset Driver

[Steen Hegelund]

Hi Philipp,

I just wanted to know if there are any outstanding items, or you think 
that the driver is acceptable as it is now?

BR
Steen

On Tue, 2021-03-16 at 10:08 +0100, Steen Hegelund wrote:
> This series provides the Microchip Sparx5 Switch Reset Driver
> 
> The Sparx5 Switch SoC has a number of components that can be reset
> individually, but at least the Switch Core needs to be in a well defined
> state at power on, when any of the Sparx5 drivers starts to access the
> Switch Core, this reset driver is available.
> 
> The reset driver is loaded early via the postcore_initcall interface, and
> will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
> that are loaded next, and the first of them to be loaded can perform the
> one-time Switch Core reset that is needed.
> 
> The driver has protection so that the system busses, DDR controller, PCI-E
> and ARM A53 CPU and a few other subsystems are not touched by the reset.
> 
> Sparx5 will no longer use the existing Ocelot chip reset driver, but use
> this new switch reset driver as it has the reset controller interface that
> allows the first client to perform the reset on behalf of all the Sparx5
> component drivers.
> 
> The Sparx5 Chip Register Model can be browsed at this location:
> https://github.com/microchip-ung/sparx-5_reginfo
> and the datasheet is available here:
> https://ww1.microchip.com/downloads/en/DeviceDoc/SparX-5_Family_L2L3_Enterprise_10G_Ethernet_Switches_Datasheet_00003822B.pdf
> 
> History:
> 
> v7 -> v8 Updated the commit descriptions to explain the change from using
>          the existing Ocelot chip reset driver to use a new switch reset
>          driver.
> 
> v6 -> v7 Use devm_platform_get_and_ioremap_resource to get the IO range.
>          Rebase on v5.12-rc1
> 
> v5 -> v6 Using the existing CPU syscon for reset protection and add a small
>          IO range for the GCB Reset Register.
> 
> v4 -> v5 Changed the two syscons into IO ranges and updated the bindings to
>          reflect this change.
> 
> v3 -> v4 Added commit message descriptions
> 
> v2 -> v3 Removed unused headers
>          Renamed the reset controller dev member.
>          Use regmap_read_poll_timeout instead of polling a function.
>          Used two separate syscon entries in the binding
>          Simplified the syscon error handling.
>          Simplified the devm_reset_controller_register error handling.
>          Moved the contents of the mchp_sparx5_reset_config function into
>          the probe function.
> 
> v1 -> v2 Removed debug prints
>          Changed the error handling to save the error code before jumping.
> 
> Steen Hegelund (3):
>   dt-bindings: reset: microchip sparx5 reset driver bindings
>   reset: mchp: sparx5: add switch reset driver
>   arm64: dts: reset: add microchip sparx5 switch reset driver
> 
>  .../bindings/reset/microchip,rst.yaml         |  58 +++++++
>  arch/arm64/boot/dts/microchip/sparx5.dtsi     |   7 +-
>  drivers/reset/Kconfig                         |   8 +
>  drivers/reset/Makefile                        |   1 +
>  drivers/reset/reset-microchip-sparx5.c        | 146 ++++++++++++++++++
>  5 files changed, 218 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
>  create mode 100644 drivers/reset/reset-microchip-sparx5.c
> 

Re: [PATCH v8 0/3] Adding the Sparx5 Switch Reset Driver

[Steen Hegelund]

Hi Philipp,

I just wanted to know if there are any outstanding items, or you think 
that the driver is acceptable as it is now?

BR
Steen

On Tue, 2021-03-16 at 10:08 +0100, Steen Hegelund wrote:
> This series provides the Microchip Sparx5 Switch Reset Driver
> 
> The Sparx5 Switch SoC has a number of components that can be reset
> individually, but at least the Switch Core needs to be in a well defined
> state at power on, when any of the Sparx5 drivers starts to access the
> Switch Core, this reset driver is available.
> 
> The reset driver is loaded early via the postcore_initcall interface, and
> will then be available for the other Sparx5 drivers (SGPIO, SwitchDev etc)
> that are loaded next, and the first of them to be loaded can perform the
> one-time Switch Core reset that is needed.
> 
> The driver has protection so that the system busses, DDR controller, PCI-E
> and ARM A53 CPU and a few other subsystems are not touched by the reset.
> 
> Sparx5 will no longer use the existing Ocelot chip reset driver, but use
> this new switch reset driver as it has the reset controller interface that
> allows the first client to perform the reset on behalf of all the Sparx5
> component drivers.
> 
> The Sparx5 Chip Register Model can be browsed at this location:
> https://github.com/microchip-ung/sparx-5_reginfo
> and the datasheet is available here:
> https://ww1.microchip.com/downloads/en/DeviceDoc/SparX-5_Family_L2L3_Enterprise_10G_Ethernet_Switches_Datasheet_00003822B.pdf
> 
> History:
> 
> v7 -> v8 Updated the commit descriptions to explain the change from using
>          the existing Ocelot chip reset driver to use a new switch reset
>          driver.
> 
> v6 -> v7 Use devm_platform_get_and_ioremap_resource to get the IO range.
>          Rebase on v5.12-rc1
> 
> v5 -> v6 Using the existing CPU syscon for reset protection and add a small
>          IO range for the GCB Reset Register.
> 
> v4 -> v5 Changed the two syscons into IO ranges and updated the bindings to
>          reflect this change.
> 
> v3 -> v4 Added commit message descriptions
> 
> v2 -> v3 Removed unused headers
>          Renamed the reset controller dev member.
>          Use regmap_read_poll_timeout instead of polling a function.
>          Used two separate syscon entries in the binding
>          Simplified the syscon error handling.
>          Simplified the devm_reset_controller_register error handling.
>          Moved the contents of the mchp_sparx5_reset_config function into
>          the probe function.
> 
> v1 -> v2 Removed debug prints
>          Changed the error handling to save the error code before jumping.
> 
> Steen Hegelund (3):
>   dt-bindings: reset: microchip sparx5 reset driver bindings
>   reset: mchp: sparx5: add switch reset driver
>   arm64: dts: reset: add microchip sparx5 switch reset driver
> 
>  .../bindings/reset/microchip,rst.yaml         |  58 +++++++
>  arch/arm64/boot/dts/microchip/sparx5.dtsi     |   7 +-
>  drivers/reset/Kconfig                         |   8 +
>  drivers/reset/Makefile                        |   1 +
>  drivers/reset/reset-microchip-sparx5.c        | 146 ++++++++++++++++++
>  5 files changed, 218 insertions(+), 2 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/reset/microchip,rst.yaml
>  create mode 100644 drivers/reset/reset-microchip-sparx5.c
> 



_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel