[PATCH RESEND 1/5] ARM: dts: clps711x: Add SYSCON nodes where it is used

[PATCH RESEND 1/5] ARM: dts: clps711x: Add SYSCON nodes where it is used

[Alexander Shiyan]

This patch adds SYSCON descriptors to framebuffer, SPI, DAI
and modem control GPIO nodes to further rework these drivers
to remove the call to the syscon_regmap_lookup_by_compatible() function.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 365931f8b48d..dacbe0d8e67a 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -108,6 +108,7 @@ fb: fb@800002c0 {
 			compatible = "cirrus,ep7209-fb";
 			reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 			clocks = <&clks CLPS711X_CLK_BUS>;
+			syscon = <&syscon1>;
 			status = "disabled";
 		};
 
@@ -147,6 +148,7 @@ spi: spi@80000500 {
 			reg = <0x80000500 0x4>;
 			interrupts = <15>;
 			clocks = <&clks CLPS711X_CLK_SPI>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -170,6 +172,7 @@ dai: dai@80002000 {
 			clocks = <&clks CLPS711X_CLK_PLL>;
 			clock-names = "pll";
 			interrupts = <32>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -181,6 +184,7 @@ syscon3: syscon@80002200 {
 
 	mctrl: mctrl {
 		compatible = "cirrus,ep7209-mctrl-gpio";
+		gpio,syscon-dev = <&syscon1 0 0>;
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
-- 
2.26.2

[PATCH RESEND 1/5] ARM: dts: clps711x: Add SYSCON nodes where it is used

[Alexander Shiyan]

This patch adds SYSCON descriptors to framebuffer, SPI, DAI
and modem control GPIO nodes to further rework these drivers
to remove the call to the syscon_regmap_lookup_by_compatible() function.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 365931f8b48d..dacbe0d8e67a 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -108,6 +108,7 @@ fb: fb@800002c0 {
 			compatible = "cirrus,ep7209-fb";
 			reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 			clocks = <&clks CLPS711X_CLK_BUS>;
+			syscon = <&syscon1>;
 			status = "disabled";
 		};
 
@@ -147,6 +148,7 @@ spi: spi@80000500 {
 			reg = <0x80000500 0x4>;
 			interrupts = <15>;
 			clocks = <&clks CLPS711X_CLK_SPI>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -170,6 +172,7 @@ dai: dai@80002000 {
 			clocks = <&clks CLPS711X_CLK_PLL>;
 			clock-names = "pll";
 			interrupts = <32>;
+			syscon = <&syscon3>;
 			status = "disabled";
 		};
 
@@ -181,6 +184,7 @@ syscon3: syscon@80002200 {
 
 	mctrl: mctrl {
 		compatible = "cirrus,ep7209-mctrl-gpio";
+		gpio,syscon-dev = <&syscon1 0 0>;
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 2/5] ARM: dts: clps711x: Add keypad node

[Alexander Shiyan]

This adds missing keypad node to basic clps711x DT.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index dacbe0d8e67a..02606547bdc5 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -182,6 +182,13 @@ syscon3: syscon@80002200 {
 		};
 	};
 
+	keypad: keypad {
+		compatible = "cirrus,ep7209-keypad";
+		interrupts = <16>;
+		syscon = <&syscon1>;
+		status = "disabled";
+	};
+
 	mctrl: mctrl {
 		compatible = "cirrus,ep7209-mctrl-gpio";
 		gpio,syscon-dev = <&syscon1 0 0>;
-- 
2.26.2

[PATCH RESEND 2/5] ARM: dts: clps711x: Add keypad node

[Alexander Shiyan]

This adds missing keypad node to basic clps711x DT.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index dacbe0d8e67a..02606547bdc5 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -182,6 +182,13 @@ syscon3: syscon@80002200 {
 		};
 	};
 
+	keypad: keypad {
+		compatible = "cirrus,ep7209-keypad";
+		interrupts = <16>;
+		syscon = <&syscon1>;
+		status = "disabled";
+	};
+
 	mctrl: mctrl {
 		compatible = "cirrus,ep7209-mctrl-gpio";
 		gpio,syscon-dev = <&syscon1 0 0>;
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 3/5] ARM: dts: clps711x: Fix serial port names

[Alexander Shiyan]

Preferred node name for serial ports is "serial".

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 02606547bdc5..9350497c1805 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -133,7 +133,7 @@ pwm: pwm@80000400 {
 			#pwm-cells = <1>;
 		};
 
-		uart1: uart@80000480 {
+		uart1: serial@80000480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80000480 0x80>;
 			interrupts = <12 13>;
@@ -157,7 +157,7 @@ syscon2: syscon@80001100 {
 			reg = <0x80001100 0x80>;
 		};
 
-		uart2: uart@80001480 {
+		uart2: serial@80001480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80001480 0x80>;
 			interrupts = <28 29>;
-- 
2.26.2

[PATCH RESEND 3/5] ARM: dts: clps711x: Fix serial port names

[Alexander Shiyan]

Preferred node name for serial ports is "serial".

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 02606547bdc5..9350497c1805 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -133,7 +133,7 @@ pwm: pwm@80000400 {
 			#pwm-cells = <1>;
 		};
 
-		uart1: uart@80000480 {
+		uart1: serial@80000480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80000480 0x80>;
 			interrupts = <12 13>;
@@ -157,7 +157,7 @@ syscon2: syscon@80001100 {
 			reg = <0x80001100 0x80>;
 		};
 
-		uart2: uart@80001480 {
+		uart2: serial@80001480 {
 			compatible = "cirrus,ep7209-uart";
 			reg = <0x80001480 0x80>;
 			interrupts = <28 29>;
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 4/5] ARM: dts: clps711x: edb7211: Add unit-address to memory node

[Alexander Shiyan]

The memory node requires a unit-address, add it.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7211-edb7211.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/ep7211-edb7211.dts b/arch/arm/boot/dts/ep7211-edb7211.dts
index da076479c8e2..7fb532f227af 100644
--- a/arch/arm/boot/dts/ep7211-edb7211.dts
+++ b/arch/arm/boot/dts/ep7211-edb7211.dts
@@ -7,7 +7,7 @@ / {
 	model = "Cirrus Logic EP7211 Development Board";
 	compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209";
 
-	memory {
+	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xc0000000 0x02000000>;
 	};
-- 
2.26.2

[PATCH RESEND 4/5] ARM: dts: clps711x: edb7211: Add unit-address to memory node

[Alexander Shiyan]

The memory node requires a unit-address, add it.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7211-edb7211.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/ep7211-edb7211.dts b/arch/arm/boot/dts/ep7211-edb7211.dts
index da076479c8e2..7fb532f227af 100644
--- a/arch/arm/boot/dts/ep7211-edb7211.dts
+++ b/arch/arm/boot/dts/ep7211-edb7211.dts
@@ -7,7 +7,7 @@ / {
 	model = "Cirrus Logic EP7211 Development Board";
 	compatible = "cirrus,edb7211", "cirrus,ep7211", "cirrus,ep7209";
 
-	memory {
+	memory@c0000000 {
 		device_type = "memory";
 		reg = <0xc0000000 0x02000000>;
 	};
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 5/5] ARM: dts: clps711x: Add an empty chosen node to top level DTSI

[Alexander Shiyan]

Missing "chosen" node can cause issues when booting a kernel
with a boot-loader that doesn't create a chosen node if this
isn't present in the DTB since the decompressor relies on a
pre-existing chosen node to be available to insert the command
line and merge other ATAGS info.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 9350497c1805..40a277370fd0 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -10,6 +10,8 @@ / {
 	model = "Cirrus Logic EP7209";
 	compatible = "cirrus,ep7209";
 
+	chosen { };
+
 	aliases {
 		gpio0 = &porta;
 		gpio1 = &portb;
-- 
2.26.2

[PATCH RESEND 5/5] ARM: dts: clps711x: Add an empty chosen node to top level DTSI

[Alexander Shiyan]

Missing "chosen" node can cause issues when booting a kernel
with a boot-loader that doesn't create a chosen node if this
isn't present in the DTB since the decompressor relies on a
pre-existing chosen node to be available to insert the command
line and merge other ATAGS info.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 9350497c1805..40a277370fd0 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -10,6 +10,8 @@ / {
 	model = "Cirrus Logic EP7209";
 	compatible = "cirrus,ep7209";
 
+	chosen { };
+
 	aliases {
 		gpio0 = &porta;
 		gpio1 = &portb;
-- 
2.26.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH RESEND 1/5] ARM: dts: clps711x: Add SYSCON nodes where it is used

[Arnd Bergmann]

On Fri, Apr 2, 2021 at 9:43 AM Alexander Shiyan <shc_work@mail.ru> wrote:
>
> This patch adds SYSCON descriptors to framebuffer, SPI, DAI
> and modem control GPIO nodes to further rework these drivers
> to remove the call to the syscon_regmap_lookup_by_compatible() function.
>
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> ---
>  arch/arm/boot/dts/ep7209.dtsi | 4 ++++
>  1 file changed, 4 insertions(+)

The patches all look good. Can you resend them to soc@kernel.org
to make them end up in patchwork for me to pick them up into the soc tree?

Thanks,

        Arnd

Re: [PATCH RESEND 1/5] ARM: dts: clps711x: Add SYSCON nodes where it is used

[Arnd Bergmann]

On Fri, Apr 2, 2021 at 9:43 AM Alexander Shiyan <shc_work@mail.ru> wrote:
>
> This patch adds SYSCON descriptors to framebuffer, SPI, DAI
> and modem control GPIO nodes to further rework these drivers
> to remove the call to the syscon_regmap_lookup_by_compatible() function.
>
> Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
> ---
>  arch/arm/boot/dts/ep7209.dtsi | 4 ++++
>  1 file changed, 4 insertions(+)

The patches all look good. Can you resend them to soc@kernel.org
to make them end up in patchwork for me to pick them up into the soc tree?

Thanks,

        Arnd

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH RESEND 5/5] ARM: dts: clps711x: Add an empty chosen node to top level DTSI

[Alexander Shiyan]

Missing "chosen" node can cause issues when booting a kernel
with a boot-loader that doesn't create a chosen node if this
isn't present in the DTB since the decompressor relies on a
pre-existing chosen node to be available to insert the command
line and merge other ATAGS info.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
---
 arch/arm/boot/dts/ep7209.dtsi | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/ep7209.dtsi b/arch/arm/boot/dts/ep7209.dtsi
index 9350497c1805..40a277370fd0 100644
--- a/arch/arm/boot/dts/ep7209.dtsi
+++ b/arch/arm/boot/dts/ep7209.dtsi
@@ -10,6 +10,8 @@ / {
 	model = "Cirrus Logic EP7209";
 	compatible = "cirrus,ep7209";
 
+	chosen { };
+
 	aliases {
 		gpio0 = &porta;
 		gpio1 = &portb;
-- 
2.26.2