All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering
@ 2021-04-07 20:14 Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 1/3] net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering mode Vladimir Oltean
                   ` (3 more replies)
  0 siblings, 4 replies; 5+ messages in thread
From: Vladimir Oltean @ 2021-04-07 20:14 UTC (permalink / raw)
  To: David S . Miller, Jakub Kicinski, netdev
  Cc: Florian Fainelli, Andrew Lunn, Vivien Didelot, Vladimir Oltean

From: Vladimir Oltean <vladimir.oltean@nxp.com>

This series addresses some user complaints regarding best-effort VLAN
filtering support on sja1105:
- switch not pushing VLAN tag on egress when it should
- switch not dropping traffic with unknown VLAN when it should
- switch not overwriting VLAN flags when it should

Those bugs are not the reason why it's called best-effort, so we should
fix them :)

Vladimir Oltean (3):
  net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering
    mode
  net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic
  net: dsa: sja1105: update existing VLANs from the bridge VLAN list

 drivers/net/dsa/sja1105/sja1105.h      |  1 +
 drivers/net/dsa/sja1105/sja1105_main.c | 61 ++++++++++++++++++--------
 2 files changed, 43 insertions(+), 19 deletions(-)

-- 
2.25.1


^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH net 1/3] net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering mode
  2021-04-07 20:14 [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
@ 2021-04-07 20:14 ` Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 2/3] net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic Vladimir Oltean
                   ` (2 subsequent siblings)
  3 siblings, 0 replies; 5+ messages in thread
From: Vladimir Oltean @ 2021-04-07 20:14 UTC (permalink / raw)
  To: David S . Miller, Jakub Kicinski, netdev
  Cc: Florian Fainelli, Andrew Lunn, Vivien Didelot, Vladimir Oltean

From: Vladimir Oltean <vladimir.oltean@nxp.com>

The best-effort VLAN filtering mode is the sja1105 driver's attempt to
allow frame tagging towards the CPU with a unique VLAN ID corresponding
to the source port at the same time as allowing the bridge to freely
alter the VLAN table. It works by making the switch classify all untagged
ingress traffic to a secret pvid managed by net/dsa/tag_8021q.c.
Also, VLAN-tagged frames are retagged to another secret VLAN managed by
tag_8021q. Both these VLANs managed by tag_8021q are called "rx_vid".
The retagged rx_vid has some bits which encode a "sub-VLAN", and the
pvid-based rx_vid has those sub-VLAN bits set to zero. Software looks at
the rx_vid and knows what port and original VLAN the packet came from.

There is a huge oversight in the setup created by the sja1105 driver for
the best-effort VLAN filtering mode. That is:

ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp4 master br0
bridge vlan del dev swp4 vid 1
bridge vlan add dev swp4 vid 1 pvid

Then we send an untagged packet from swp2 and expect the switch to
forward it to swp4 and deliver it with VLAN 1 added. It is forwarded,
except the packet is egress-untagged.

This happens because of the way in which tag_8021q works (there is a
detailed picture in net/dsa/tag_8021q.c, above dsa_8021q_setup_port).
In the example above, the tag_8021q pvid of swp2 is 1026. This VLAN is
added to all other switch ports, to allow untagged traffic forwarding.
On all ports, the tag_8021q pvid of 1026 is installed as egress-untagged,
in order to hide the existence of DSA tag_8021q from the user.

This is fine, except when the real (bridge) pvid is egress-tagged, it
isn't. The user _wants_ to see this VLAN in the outside world, and we
can't really do that, because the sja1105 driver doesn't use that VLAN
but another one which the user knows nothing about.

As a side note, this only happens for untagged traffic on the ingress
port. If the packet arrives as pvid-tagged (i.e. tagged with VID 1)
on a port with tag_8021q, then the packet is classified to VLAN ID 1
(the bridge pvid) as opposed to the tag_8021q pvid. So we don't have
the same problem.

Consider the following more generic example:

Port             | sw0p0 sw0p1 sw0p2 sw0p3  |  sw1p0 sw1p1 sw1p2 sw1p3
=================+==========================+==========================
tag_8021q rx_vid | 1024  1025  1026  1027   |  1088  1089  1090  1091
tag_8021q flags  | pvid  pvid  pvid  pvid   |  pvid  pvid  pvid  pvid
                 | untag untag untag untag  |  untag untag untag untag
Bridge VLAN      |  1     1     2     1     |    3     2     2     1
Bridge flags     | pvid        pvid         |   pvid  pvid
                 | untag untag              |

What is not shown in the above table, because it would make it too
bloated, is that:
- VLAN 1024 is added to sw0p1, sw0p2, sw0p3, sw1p0, sw1p1, sw1p2, sw1p3
  as egress-untagged but not pvid.
- VLAN 1025 is added to sw0p0, sw0p2, sw0p3, sw1p0, sw1p1, sw1p2, sw1p3
  as egress-untagged but not pvid
- etc

The following pattern emerges:
A VLAN which is pvid on any port in the bridging domain (therefore has a
tag_8021q rx_vid) and is egress-tagged on another (potentially the same)
port will leak the tag_8021q VLAN. Every egress-tagged bridge VLAN that
is a pvid on another port must have a retagging rule from the tag_8021q
rx_vid to the bridge VLAN. In the above example, there needs to be a
retagging rule on the egress of sw0p1 for traffic with the tag_8021q
rx_vid 1024 (coming from sw0p0) towards VID 1. For sw0p3, we need to
retag VLAN 1024. For sw0p2, we need to retag VID 1090, etc etc.

So the data would indicate that, at the very least, we should retag the
tag_8021q pvid back towards the original bridge pvid on the egress ports
where this bridge VLAN is installed as egress-tagged. We could do that,
except:
- We only have 32 VLAN retagging entries in the sja1105, and we do use
  them for other purposes too.
- VLAN retagging works in hardware by making use of a special "loopback
  port" which is limited to only 1Gbps of bandwidth. When using the
  loopback port for traffic retagged towards the CPU that's fine because
  the CPU port is gigabit anyway, but when we start involving it in the
  autonomous forwarding data path we have a problem, because we'd
  bottleneck it.

So we take a step back and think a bit more about the problem.

Due to the need to plug another hole - pvid-tagged traffic is not seen
with a tag_8021q rx_vid by software, but with the bridge pvid, say 1 -
sja1105_build_subvlans() already creates VLAN retagging entries towards
the CPU even for the bridge pvid, not just for tagged VLANs.
That is to say, even if we let the bridge pvid be the hardware's pvid in
best-effort VLAN filtering mode, untagged and pvid-tagged packets will
still arrive at the CPU as tagged with the tag_8021q rx_vid, because
they will both hit the same retagging rule.

But that actually means we don't _need_ the tag_8021q module to dictate
a pvid value for us. We can rely on retagging just fine, and let the
bridge dictate the pvid. This solves the problem in a much cleaner way:
because the packets in the autonomous data path are now classified to
the bridge pvid, the egress-tagged setting on the egress port works just
fine.

[ note that this means we can always rely on VLAN retagging towards the
  CPU, and never on changing the port's pvid. And because the pvid is no
  longer managed by tag_8021q, we can even go as far as enable
  Independent VLAN Learning again. But I digress, that is an
  optimization to make for net-next, this is just to fix a bug ]

The commit I'm blaming is the one which introduced the problem, but the
fix relies on a mechanism that was only added a few commits later:
3f01c91aab92 ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q
sub-VLANs"). This is fine, since they all went into the same kernel
release (v5.8).

Fixes: 2cafa72e516f ("net: dsa: sja1105: add a new best_effort_vlan_filtering devlink parameter")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 drivers/net/dsa/sja1105/sja1105_main.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index d9c198ca0197..8b380ccd95cf 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -2240,10 +2240,10 @@ static int sja1105_commit_pvid(struct sja1105_private *priv)
 	struct list_head *vlan_list;
 	int rc = 0;
 
-	if (priv->vlan_state == SJA1105_VLAN_FILTERING_FULL)
-		vlan_list = &priv->bridge_vlans;
-	else
+	if (priv->vlan_state == SJA1105_VLAN_UNAWARE)
 		vlan_list = &priv->dsa_8021q_vlans;
+	else
+		vlan_list = &priv->bridge_vlans;
 
 	list_for_each_entry(v, vlan_list, list) {
 		if (v->pvid) {
@@ -2290,6 +2290,21 @@ sja1105_build_dsa_8021q_vlans(struct sja1105_private *priv,
 	list_for_each_entry(v, &priv->dsa_8021q_vlans, list) {
 		int match = v->vid;
 
+		/* In best-effort VLAN filtering mode, the pvid of the port is
+		 * no longer the tag_8021q rx_vid, but the bridge pvid is.
+		 * The tag_8021q rx_vid is just used for retagging the bridge
+		 * pvid towards the CPU. So let's install only the rx_vid
+		 * values which are strictly required. This means that the
+		 * rxvlan is still installed on the port on which tag_8021q
+		 * thinks it must be pvid (the source port) - this is required
+		 * by the retagging table - but not on the ports where this
+		 * VLAN isn't a pvid (the destination ports).
+		 */
+		if (priv->vlan_state == SJA1105_VLAN_BEST_EFFORT &&
+		    vid_is_dsa_8021q_rxvlan(v->vid) &&
+		    dsa_8021q_rx_subvlan(v->vid) == 0 && !v->pvid)
+			continue;
+
 		new_vlan[match].vlanid = v->vid;
 		new_vlan[match].vmemb_port |= BIT(v->port);
 		new_vlan[match].vlan_bc |= BIT(v->port);
-- 
2.25.1


^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [PATCH net 2/3] net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic
  2021-04-07 20:14 [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 1/3] net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering mode Vladimir Oltean
@ 2021-04-07 20:14 ` Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 3/3] net: dsa: sja1105: update existing VLANs from the bridge VLAN list Vladimir Oltean
  2021-04-07 20:46 ` [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
  3 siblings, 0 replies; 5+ messages in thread
From: Vladimir Oltean @ 2021-04-07 20:14 UTC (permalink / raw)
  To: David S . Miller, Jakub Kicinski, netdev
  Cc: Florian Fainelli, Andrew Lunn, Vivien Didelot, Vladimir Oltean

From: Vladimir Oltean <vladimir.oltean@nxp.com>

One thing became visible when writing the blamed commit, and that was
that STP and PTP frames injected by net/dsa/tag_sja1105.c using the
deferred xmit mechanism are always classified to the pvid of the CPU
port, regardless of whatever VLAN there might be in these packets.

So a decision needed to be taken regarding the mechanism through which
we should ensure that delivery of STP and PTP traffic is possible when
we are in a VLAN awareness mode that involves tag_8021q. This is because
tag_8021q is not concerned with managing the pvid of the CPU port, since
as far as tag_8021q is concerned, no traffic should be sent as untagged
from the CPU port. So we end up not actually having a pvid on the CPU
port if we only listen to tag_8021q, and unless we do something about it.

The decision taken at the time was to keep VLAN 1 in the list of
priv->dsa_8021q_vlans, and make it a pvid of the CPU port. This ensures
that STP and PTP frames can always be sent to the outside world.

However there is a problem. If we do the following while we are in
the best_effort_vlan_filtering=true mode:

ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan del dev swp2 vid 1

Then untagged and pvid-tagged frames should be dropped. But we observe
that they aren't, and this is because of the precaution we took that VID
1 is always installed on all ports.

So clearly VLAN 1 is not good for this purpose. What about VLAN 0?
Well, VLAN 0 is managed by the 8021q module, and that module wants to
ensure that 802.1p tagged frames are always received by a port, and are
always transmitted as VLAN-tagged (with VLAN ID 0). Whereas we want our
STP and PTP frames to be untagged if the stack sent them as untagged -
we don't want the driver to just decide out of the blue that it adds
VID 0 to some packets.

So what to do?

Well, there is one other VLAN that is reserved, and that is 4095:
$ ip link add link swp2 name swp2.4095 type vlan id 4095
Error: 8021q: Invalid VLAN id.
$ bridge vlan add dev swp2 vid 4095
Error: bridge: Vlan id is invalid.

After we made this change, VLAN 1 is indeed forwarded and/or dropped
according to the bridge VLAN table, there are no further alterations
done by the sja1105 driver.

Fixes: ec5ae61076d0 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 drivers/net/dsa/sja1105/sja1105.h      |  1 +
 drivers/net/dsa/sja1105/sja1105_main.c | 21 +++++++++------------
 2 files changed, 10 insertions(+), 12 deletions(-)

diff --git a/drivers/net/dsa/sja1105/sja1105.h b/drivers/net/dsa/sja1105/sja1105.h
index f9e87fb33da0..6957cb853a70 100644
--- a/drivers/net/dsa/sja1105/sja1105.h
+++ b/drivers/net/dsa/sja1105/sja1105.h
@@ -13,6 +13,7 @@
 #include <linux/mutex.h>
 #include "sja1105_static_config.h"
 
+#define SJA1105_DEFAULT_VLAN		(VLAN_N_VID - 1)
 #define SJA1105_NUM_PORTS		5
 #define SJA1105_NUM_TC			8
 #define SJA1105ET_FDB_BIN_SIZE		4
diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 8b380ccd95cf..61133098f588 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -321,6 +321,13 @@ static int sja1105_init_l2_lookup_params(struct sja1105_private *priv)
 	return 0;
 }
 
+/* Set up a default VLAN for untagged traffic injected from the CPU
+ * using management routes (e.g. STP, PTP) as opposed to tag_8021q.
+ * All DT-defined ports are members of this VLAN, and there are no
+ * restrictions on forwarding (since the CPU selects the destination).
+ * Frames from this VLAN will always be transmitted as untagged, and
+ * neither the bridge nor the 8021q module cannot create this VLAN ID.
+ */
 static int sja1105_init_static_vlan(struct sja1105_private *priv)
 {
 	struct sja1105_table *table;
@@ -330,17 +337,13 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv)
 		.vmemb_port = 0,
 		.vlan_bc = 0,
 		.tag_port = 0,
-		.vlanid = 1,
+		.vlanid = SJA1105_DEFAULT_VLAN,
 	};
 	struct dsa_switch *ds = priv->ds;
 	int port;
 
 	table = &priv->static_config.tables[BLK_IDX_VLAN_LOOKUP];
 
-	/* The static VLAN table will only contain the initial pvid of 1.
-	 * All other VLANs are to be configured through dynamic entries,
-	 * and kept in the static configuration table as backing memory.
-	 */
 	if (table->entry_count) {
 		kfree(table->entries);
 		table->entry_count = 0;
@@ -353,9 +356,6 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv)
 
 	table->entry_count = 1;
 
-	/* VLAN 1: all DT-defined ports are members; no restrictions on
-	 * forwarding; always transmit as untagged.
-	 */
 	for (port = 0; port < ds->num_ports; port++) {
 		struct sja1105_bridge_vlan *v;
 
@@ -366,15 +366,12 @@ static int sja1105_init_static_vlan(struct sja1105_private *priv)
 		pvid.vlan_bc |= BIT(port);
 		pvid.tag_port &= ~BIT(port);
 
-		/* Let traffic that don't need dsa_8021q (e.g. STP, PTP) be
-		 * transmitted as untagged.
-		 */
 		v = kzalloc(sizeof(*v), GFP_KERNEL);
 		if (!v)
 			return -ENOMEM;
 
 		v->port = port;
-		v->vid = 1;
+		v->vid = SJA1105_DEFAULT_VLAN;
 		v->untagged = true;
 		if (dsa_is_cpu_port(ds, port))
 			v->pvid = true;
-- 
2.25.1


^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [PATCH net 3/3] net: dsa: sja1105: update existing VLANs from the bridge VLAN list
  2021-04-07 20:14 [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 1/3] net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering mode Vladimir Oltean
  2021-04-07 20:14 ` [PATCH net 2/3] net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic Vladimir Oltean
@ 2021-04-07 20:14 ` Vladimir Oltean
  2021-04-07 20:46 ` [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
  3 siblings, 0 replies; 5+ messages in thread
From: Vladimir Oltean @ 2021-04-07 20:14 UTC (permalink / raw)
  To: David S . Miller, Jakub Kicinski, netdev
  Cc: Florian Fainelli, Andrew Lunn, Vivien Didelot, Vladimir Oltean

From: Vladimir Oltean <vladimir.oltean@nxp.com>

When running this sequence of operations:

ip link add br0 type bridge vlan_filtering 1
ip link set swp4 master br0
bridge vlan add dev swp4 vid 1

We observe the traffic sent on swp4 is still untagged, even though the
bridge has overwritten the existing VLAN entry:

port    vlan ids
swp4     1 PVID

br0      1 PVID Egress Untagged

This happens because we didn't consider that the 'bridge vlan add'
command just overwrites VLANs like it's nothing. We treat the 'vid 1
pvid untagged' and the 'vid 1' as two separate VLANs, and the first
still has precedence when calling sja1105_build_vlan_table. Obviously
there is a disagreement regarding semantics, and we end up doing
something unexpected from the PoV of the bridge.

Let's actually consider an "existing VLAN" to be one which is on the
same port, and has the same VLAN ID, as one we already have, and update
it if it has different flags than we do.

The first blamed commit is the one introducing the bug, the second one
is the latest on top of which the bugfix still applies.

Fixes: ec5ae61076d0 ("net: dsa: sja1105: save/restore VLANs using a delta commit method")
Fixes: 5899ee367ab3 ("net: dsa: tag_8021q: add a context structure")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
---
 drivers/net/dsa/sja1105/sja1105_main.c | 19 +++++++++++++++----
 1 file changed, 15 insertions(+), 4 deletions(-)

diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 61133098f588..5e40ee14030a 100644
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -2829,11 +2829,22 @@ static int sja1105_vlan_add_one(struct dsa_switch *ds, int port, u16 vid,
 	bool pvid = flags & BRIDGE_VLAN_INFO_PVID;
 	struct sja1105_bridge_vlan *v;
 
-	list_for_each_entry(v, vlan_list, list)
-		if (v->port == port && v->vid == vid &&
-		    v->untagged == untagged && v->pvid == pvid)
+	list_for_each_entry(v, vlan_list, list) {
+		if (v->port == port && v->vid == vid) {
 			/* Already added */
-			return 0;
+			if (v->untagged == untagged && v->pvid == pvid)
+				/* Nothing changed */
+				return 0;
+
+			/* It's the same VLAN, but some of the flags changed
+			 * and the user did not bother to delete it first.
+			 * Update it and trigger sja1105_build_vlan_table.
+			 */
+			v->untagged = untagged;
+			v->pvid = pvid;
+			return 1;
+		}
+	}
 
 	v = kzalloc(sizeof(*v), GFP_KERNEL);
 	if (!v) {
-- 
2.25.1


^ permalink raw reply related	[flat|nested] 5+ messages in thread

* Re: [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering
  2021-04-07 20:14 [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
                   ` (2 preceding siblings ...)
  2021-04-07 20:14 ` [PATCH net 3/3] net: dsa: sja1105: update existing VLANs from the bridge VLAN list Vladimir Oltean
@ 2021-04-07 20:46 ` Vladimir Oltean
  3 siblings, 0 replies; 5+ messages in thread
From: Vladimir Oltean @ 2021-04-07 20:46 UTC (permalink / raw)
  To: David S . Miller, Jakub Kicinski, netdev
  Cc: Florian Fainelli, Andrew Lunn, Vivien Didelot, Vladimir Oltean

On Wed, Apr 07, 2021 at 11:14:49PM +0300, Vladimir Oltean wrote:
> From: Vladimir Oltean <vladimir.oltean@nxp.com>
> 
> This series addresses some user complaints regarding best-effort VLAN
> filtering support on sja1105:
> - switch not pushing VLAN tag on egress when it should
> - switch not dropping traffic with unknown VLAN when it should
> - switch not overwriting VLAN flags when it should
> 
> Those bugs are not the reason why it's called best-effort, so we should
> fix them :)
> 
> Vladimir Oltean (3):
>   net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering
>     mode
>   net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic
>   net: dsa: sja1105: update existing VLANs from the bridge VLAN list
> 
>  drivers/net/dsa/sja1105/sja1105.h      |  1 +
>  drivers/net/dsa/sja1105/sja1105_main.c | 61 ++++++++++++++++++--------
>  2 files changed, 43 insertions(+), 19 deletions(-)
> 
> -- 
> 2.25.1
> 

Please don't apply these patches yet. I finished regression testing and
it looks like patch 1 breaks PTP for some reason I'm afraid to even think
of now - the RX timestamps are still collected but synchronization looks
flat by around 1 ms.

If my suspicion is right and the VLAN retagging affects PTP traffic too
(which should hit a trap-to-host rule before that even takes place),
then the MAC timestamp might be replaced with a timestamp taken on the
internal loopback port, which would be pretty nasty. Or the strict
delivery order guarantees towards the DSA master (first comes the PTP
frame, then the meta frame holding the RX timestamp) might no longer be
true if the original PTP frame is dropped in hardware because its
VLAN-retagged replacement is sent to the CPU instead? I don't know. I'll
do some more debugging tomorrow.

^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2021-04-07 20:46 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-07 20:14 [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean
2021-04-07 20:14 ` [PATCH net 1/3] net: dsa: sja1105: use the bridge pvid in best_effort_vlan_filtering mode Vladimir Oltean
2021-04-07 20:14 ` [PATCH net 2/3] net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic Vladimir Oltean
2021-04-07 20:14 ` [PATCH net 3/3] net: dsa: sja1105: update existing VLANs from the bridge VLAN list Vladimir Oltean
2021-04-07 20:46 ` [PATCH net 0/3] Fixes for sja1105 best-effort VLAN filtering Vladimir Oltean

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.