All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver
@ 2021-05-10 10:40 ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Hello,

This is a short series bringing a useful feature for drivers which are a
little bit constrained regarding their number of native CS. As
manufacturer tend to group chips in arrays to enlarge the overall
available space, it might be useful to other controller drivers to make
use of the added DT property (cs-gpios) as well as the core helper which
is being introduced to parse this DT property and returned a CS array
with either empty cells (native CS are being used) or a GPIO descriptor
structure pointer (GPIO CS).

This is applied to the Arasan NAND controller driver which involved a
little bit more boilerplate than estimated I thought due to its internal
constraints regarding the bond between CS and RB.

Cheers,
Miquèl

Changes in v2:
* Rebased on top of v5.13-rc1
* This time I'm CC'ing Rob + DT ML...

Miquel Raynal (5):
  dt-binding: mtd: nand: Document gpio-cs property
  mtd: rawnand: Move struct gpio_desc declaration to the top
  mtd: rawnand: Add a helper to parse the gpio-cs DT property
  mtd: rawnand: arasan: Ensure proper configuration for the asserted
    target
  mtd: rawnand: arasan: Leverage additional GPIO CS

 .../bindings/mtd/nand-controller.yaml         |  16 +-
 drivers/mtd/nand/raw/arasan-nand-controller.c | 238 +++++++++++++-----
 drivers/mtd/nand/raw/nand_base.c              |  38 +++
 include/linux/mtd/rawnand.h                   |   6 +-
 4 files changed, 240 insertions(+), 58 deletions(-)

-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver
@ 2021-05-10 10:40 ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Hello,

This is a short series bringing a useful feature for drivers which are a
little bit constrained regarding their number of native CS. As
manufacturer tend to group chips in arrays to enlarge the overall
available space, it might be useful to other controller drivers to make
use of the added DT property (cs-gpios) as well as the core helper which
is being introduced to parse this DT property and returned a CS array
with either empty cells (native CS are being used) or a GPIO descriptor
structure pointer (GPIO CS).

This is applied to the Arasan NAND controller driver which involved a
little bit more boilerplate than estimated I thought due to its internal
constraints regarding the bond between CS and RB.

Cheers,
Miquèl

Changes in v2:
* Rebased on top of v5.13-rc1
* This time I'm CC'ing Rob + DT ML...

Miquel Raynal (5):
  dt-binding: mtd: nand: Document gpio-cs property
  mtd: rawnand: Move struct gpio_desc declaration to the top
  mtd: rawnand: Add a helper to parse the gpio-cs DT property
  mtd: rawnand: arasan: Ensure proper configuration for the asserted
    target
  mtd: rawnand: arasan: Leverage additional GPIO CS

 .../bindings/mtd/nand-controller.yaml         |  16 +-
 drivers/mtd/nand/raw/arasan-nand-controller.c | 238 +++++++++++++-----
 drivers/mtd/nand/raw/nand_base.c              |  38 +++
 include/linux/mtd/rawnand.h                   |   6 +-
 4 files changed, 240 insertions(+), 58 deletions(-)

-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
  2021-05-10 10:40 ` Miquel Raynal
@ 2021-05-10 10:40   ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

To reach higher capacities, arrays of chips are now pretty common.
Unfortunately, most of the controllers have been designed a decade ago
and did not all anticipate the need for several chip-selects. The new
cs-gpios property allows to workaround this limitation by adding as many
GPIO chip-select as needed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index 678b39952502..70a400e385b2 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -38,6 +38,15 @@ properties:
 
   ranges: true
 
+  cs-gpios:
+    description:
+      Array of chip-select available to the controller. The first
+      entries are a 1:1 mapping of the available chip-select on the
+      NAND controller (even if they are not used). As many additional
+      chip-select as needed may follow and should be phandles of GPIO
+      lines. 'reg' entries of the NAND chip subnodes become indexes of
+      this array when this property is present.
+
 patternProperties:
   "^nand@[a-f0-9]$":
     type: object
@@ -164,14 +173,19 @@ examples:
     nand-controller {
       #address-cells = <1>;
       #size-cells = <0>;
+      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
 
       /* controller specific properties */
 
       nand@0 {
-        reg = <0>;
+        reg = <0>; /* Native CS */
         nand-use-soft-ecc-engine;
         nand-ecc-algo = "bch";
 
         /* controller specific properties */
       };
+
+      nand@1 {
+        reg = <1>; /* GPIO CS */
+      };
     };
-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
@ 2021-05-10 10:40   ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

To reach higher capacities, arrays of chips are now pretty common.
Unfortunately, most of the controllers have been designed a decade ago
and did not all anticipate the need for several chip-selects. The new
cs-gpios property allows to workaround this limitation by adding as many
GPIO chip-select as needed.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
 1 file changed, 15 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index 678b39952502..70a400e385b2 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -38,6 +38,15 @@ properties:
 
   ranges: true
 
+  cs-gpios:
+    description:
+      Array of chip-select available to the controller. The first
+      entries are a 1:1 mapping of the available chip-select on the
+      NAND controller (even if they are not used). As many additional
+      chip-select as needed may follow and should be phandles of GPIO
+      lines. 'reg' entries of the NAND chip subnodes become indexes of
+      this array when this property is present.
+
 patternProperties:
   "^nand@[a-f0-9]$":
     type: object
@@ -164,14 +173,19 @@ examples:
     nand-controller {
       #address-cells = <1>;
       #size-cells = <0>;
+      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
 
       /* controller specific properties */
 
       nand@0 {
-        reg = <0>;
+        reg = <0>; /* Native CS */
         nand-use-soft-ecc-engine;
         nand-ecc-algo = "bch";
 
         /* controller specific properties */
       };
+
+      nand@1 {
+        reg = <1>; /* GPIO CS */
+      };
     };
-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
  2021-05-10 10:40 ` Miquel Raynal
@ 2021-05-10 10:40   ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

The struct gpio_desc is declared in the middle of the rawnand.h header,
right before the first function using it (nand_gpio_waitrdy). Before
adding a new function and to make it clear: move the declaration to the
top of the file.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 include/linux/mtd/rawnand.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 29df2f43dcb5..93f5c0196a09 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -24,6 +24,7 @@
 #include <linux/types.h>
 
 struct nand_chip;
+struct gpio_desc;
 
 /* The maximum number of NAND chips in an array */
 #define NAND_MAX_CHIPS		8
@@ -1413,7 +1414,6 @@ void nand_cleanup(struct nand_chip *chip);
  * instruction and have no physical pin to check it.
  */
 int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms);
-struct gpio_desc;
 int nand_gpio_waitrdy(struct nand_chip *chip, struct gpio_desc *gpiod,
 		      unsigned long timeout_ms);
 
-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
@ 2021-05-10 10:40   ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

The struct gpio_desc is declared in the middle of the rawnand.h header,
right before the first function using it (nand_gpio_waitrdy). Before
adding a new function and to make it clear: move the declaration to the
top of the file.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 include/linux/mtd/rawnand.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 29df2f43dcb5..93f5c0196a09 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -24,6 +24,7 @@
 #include <linux/types.h>
 
 struct nand_chip;
+struct gpio_desc;
 
 /* The maximum number of NAND chips in an array */
 #define NAND_MAX_CHIPS		8
@@ -1413,7 +1414,6 @@ void nand_cleanup(struct nand_chip *chip);
  * instruction and have no physical pin to check it.
  */
 int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms);
-struct gpio_desc;
 int nand_gpio_waitrdy(struct nand_chip *chip, struct gpio_desc *gpiod,
 		      unsigned long timeout_ms);
 
-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 3/5] mtd: rawnand: Add a helper to parse the gpio-cs DT property
  2021-05-10 10:40 ` Miquel Raynal
@ 2021-05-10 10:40   ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.

Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/nand_base.c | 38 ++++++++++++++++++++++++++++++++
 include/linux/mtd/rawnand.h      |  4 ++++
 2 files changed, 42 insertions(+)

diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index fb072c444495..ba09d6b6e1ce 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -42,6 +42,7 @@
 #include <linux/io.h>
 #include <linux/mtd/partitions.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/gpio/consumer.h>
 
 #include "internals.h"
@@ -5078,6 +5079,43 @@ static int of_get_nand_secure_regions(struct nand_chip *chip)
 	return 0;
 }
 
+/**
+ * rawnand_dt_parse_gpio_cs - Parse the gpio-cs property of a controller
+ * @dev: Device that will be parsed. Also used for managed allocations.
+ * @cs_array: Array of GPIO desc pointers allocated on success
+ * @ncs_array: Number of entries in @cs_array updated on success.
+ * @return 0 on success, an error otherwise.
+ */
+int rawnand_dt_parse_gpio_cs(struct device *dev, struct gpio_desc ***cs_array,
+			     unsigned int *ncs_array)
+{
+	struct device_node *np = dev->of_node;
+	struct gpio_desc **descs;
+	int ndescs, i;
+
+	ndescs = of_gpio_named_count(np, "cs-gpios");
+	if (ndescs < 0) {
+		dev_dbg(dev, "No valid cs-gpios property\n");
+		return 0;
+	}
+
+	descs = devm_kcalloc(dev, ndescs, sizeof(*descs), GFP_KERNEL);
+	if (!descs)
+		return -ENOMEM;
+
+	for (i = 0; i < ndescs; i++) {
+		descs[i] = gpiod_get_index_optional(dev, "cs", i,
+						    GPIOD_OUT_HIGH);
+		if (IS_ERR(descs[i]))
+			return PTR_ERR(descs[i]);
+	}
+
+	*ncs_array = ndescs;
+	*cs_array = descs;
+
+	return 0;
+}
+
 static int rawnand_dt_init(struct nand_chip *chip)
 {
 	struct nand_device *nand = mtd_to_nanddev(nand_to_mtd(chip));
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 93f5c0196a09..e01255a9e591 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -1446,4 +1446,8 @@ static inline void *nand_get_data_buf(struct nand_chip *chip)
 	return chip->data_buf;
 }
 
+/* Parse the gpio-cs property */
+int rawnand_dt_parse_gpio_cs(struct device *dev, struct gpio_desc ***cs_array,
+			     unsigned int *ncs_array);
+
 #endif /* __LINUX_MTD_RAWNAND_H */
-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 3/5] mtd: rawnand: Add a helper to parse the gpio-cs DT property
@ 2021-05-10 10:40   ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.

Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/nand_base.c | 38 ++++++++++++++++++++++++++++++++
 include/linux/mtd/rawnand.h      |  4 ++++
 2 files changed, 42 insertions(+)

diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index fb072c444495..ba09d6b6e1ce 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -42,6 +42,7 @@
 #include <linux/io.h>
 #include <linux/mtd/partitions.h>
 #include <linux/of.h>
+#include <linux/of_gpio.h>
 #include <linux/gpio/consumer.h>
 
 #include "internals.h"
@@ -5078,6 +5079,43 @@ static int of_get_nand_secure_regions(struct nand_chip *chip)
 	return 0;
 }
 
+/**
+ * rawnand_dt_parse_gpio_cs - Parse the gpio-cs property of a controller
+ * @dev: Device that will be parsed. Also used for managed allocations.
+ * @cs_array: Array of GPIO desc pointers allocated on success
+ * @ncs_array: Number of entries in @cs_array updated on success.
+ * @return 0 on success, an error otherwise.
+ */
+int rawnand_dt_parse_gpio_cs(struct device *dev, struct gpio_desc ***cs_array,
+			     unsigned int *ncs_array)
+{
+	struct device_node *np = dev->of_node;
+	struct gpio_desc **descs;
+	int ndescs, i;
+
+	ndescs = of_gpio_named_count(np, "cs-gpios");
+	if (ndescs < 0) {
+		dev_dbg(dev, "No valid cs-gpios property\n");
+		return 0;
+	}
+
+	descs = devm_kcalloc(dev, ndescs, sizeof(*descs), GFP_KERNEL);
+	if (!descs)
+		return -ENOMEM;
+
+	for (i = 0; i < ndescs; i++) {
+		descs[i] = gpiod_get_index_optional(dev, "cs", i,
+						    GPIOD_OUT_HIGH);
+		if (IS_ERR(descs[i]))
+			return PTR_ERR(descs[i]);
+	}
+
+	*ncs_array = ndescs;
+	*cs_array = descs;
+
+	return 0;
+}
+
 static int rawnand_dt_init(struct nand_chip *chip)
 {
 	struct nand_device *nand = mtd_to_nanddev(nand_to_mtd(chip));
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 93f5c0196a09..e01255a9e591 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -1446,4 +1446,8 @@ static inline void *nand_get_data_buf(struct nand_chip *chip)
 	return chip->data_buf;
 }
 
+/* Parse the gpio-cs property */
+int rawnand_dt_parse_gpio_cs(struct device *dev, struct gpio_desc ***cs_array,
+			     unsigned int *ncs_array);
+
 #endif /* __LINUX_MTD_RAWNAND_H */
-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 4/5] mtd: rawnand: arasan: Ensure proper configuration for the asserted target
  2021-05-10 10:40 ` Miquel Raynal
@ 2021-05-10 10:40   ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.

As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.

Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/arasan-nand-controller.c | 90 ++++++++++++-------
 1 file changed, 57 insertions(+), 33 deletions(-)

diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 549aac00228e..390f8d719c25 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -273,6 +273,37 @@ static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
 	return 0;
 }
 
+static int anfc_select_target(struct nand_chip *chip, int target)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	int ret;
+
+	/* Update the controller timings and the potential ECC configuration */
+	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
+
+	/* Update clock frequency */
+	if (nfc->cur_clk != anand->clk) {
+		clk_disable_unprepare(nfc->controller_clk);
+		ret = clk_set_rate(nfc->controller_clk, anand->clk);
+		if (ret) {
+			dev_err(nfc->dev, "Failed to change clock rate\n");
+			return ret;
+		}
+
+		ret = clk_prepare_enable(nfc->controller_clk);
+		if (ret) {
+			dev_err(nfc->dev,
+				"Failed to re-enable the controller clock\n");
+			return ret;
+		}
+
+		nfc->cur_clk = anand->clk;
+	}
+
+	return 0;
+}
+
 /*
  * When using the embedded hardware ECC engine, the controller is in charge of
  * feeding the engine with, first, the ECC residue present in the data array.
@@ -401,6 +432,18 @@ static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
 	return 0;
 }
 
+static int anfc_sel_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
+				     int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_read_page_hw_ecc(chip, buf, oob_required, page);
+};
+
 static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 				  int oob_required, int page)
 {
@@ -461,6 +504,18 @@ static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 	return ret;
 }
 
+static int anfc_sel_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
+				      int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_write_page_hw_ecc(chip, buf, oob_required, page);
+};
+
 /* NAND framework ->exec_op() hooks and related helpers */
 static int anfc_parse_instructions(struct nand_chip *chip,
 				   const struct nand_subop *subop,
@@ -753,37 +808,6 @@ static const struct nand_op_parser anfc_op_parser = NAND_OP_PARSER(
 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
 	);
 
-static int anfc_select_target(struct nand_chip *chip, int target)
-{
-	struct anand *anand = to_anand(chip);
-	struct arasan_nfc *nfc = to_anfc(chip->controller);
-	int ret;
-
-	/* Update the controller timings and the potential ECC configuration */
-	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
-
-	/* Update clock frequency */
-	if (nfc->cur_clk != anand->clk) {
-		clk_disable_unprepare(nfc->controller_clk);
-		ret = clk_set_rate(nfc->controller_clk, anand->clk);
-		if (ret) {
-			dev_err(nfc->dev, "Failed to change clock rate\n");
-			return ret;
-		}
-
-		ret = clk_prepare_enable(nfc->controller_clk);
-		if (ret) {
-			dev_err(nfc->dev,
-				"Failed to re-enable the controller clock\n");
-			return ret;
-		}
-
-		nfc->cur_clk = anand->clk;
-	}
-
-	return 0;
-}
-
 static int anfc_check_op(struct nand_chip *chip,
 			 const struct nand_operation *op)
 {
@@ -1007,8 +1031,8 @@ static int anfc_init_hw_ecc_controller(struct arasan_nfc *nfc,
 	if (!anand->bch)
 		return -EINVAL;
 
-	ecc->read_page = anfc_read_page_hw_ecc;
-	ecc->write_page = anfc_write_page_hw_ecc;
+	ecc->read_page = anfc_sel_read_page_hw_ecc;
+	ecc->write_page = anfc_sel_write_page_hw_ecc;
 
 	return 0;
 }
-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 4/5] mtd: rawnand: arasan: Ensure proper configuration for the asserted target
@ 2021-05-10 10:40   ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.

As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.

Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/arasan-nand-controller.c | 90 ++++++++++++-------
 1 file changed, 57 insertions(+), 33 deletions(-)

diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 549aac00228e..390f8d719c25 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -273,6 +273,37 @@ static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
 	return 0;
 }
 
+static int anfc_select_target(struct nand_chip *chip, int target)
+{
+	struct anand *anand = to_anand(chip);
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	int ret;
+
+	/* Update the controller timings and the potential ECC configuration */
+	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
+
+	/* Update clock frequency */
+	if (nfc->cur_clk != anand->clk) {
+		clk_disable_unprepare(nfc->controller_clk);
+		ret = clk_set_rate(nfc->controller_clk, anand->clk);
+		if (ret) {
+			dev_err(nfc->dev, "Failed to change clock rate\n");
+			return ret;
+		}
+
+		ret = clk_prepare_enable(nfc->controller_clk);
+		if (ret) {
+			dev_err(nfc->dev,
+				"Failed to re-enable the controller clock\n");
+			return ret;
+		}
+
+		nfc->cur_clk = anand->clk;
+	}
+
+	return 0;
+}
+
 /*
  * When using the embedded hardware ECC engine, the controller is in charge of
  * feeding the engine with, first, the ECC residue present in the data array.
@@ -401,6 +432,18 @@ static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
 	return 0;
 }
 
+static int anfc_sel_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
+				     int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_read_page_hw_ecc(chip, buf, oob_required, page);
+};
+
 static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 				  int oob_required, int page)
 {
@@ -461,6 +504,18 @@ static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 	return ret;
 }
 
+static int anfc_sel_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
+				      int oob_required, int page)
+{
+	int ret;
+
+	ret = anfc_select_target(chip, chip->cur_cs);
+	if (ret)
+		return ret;
+
+	return anfc_write_page_hw_ecc(chip, buf, oob_required, page);
+};
+
 /* NAND framework ->exec_op() hooks and related helpers */
 static int anfc_parse_instructions(struct nand_chip *chip,
 				   const struct nand_subop *subop,
@@ -753,37 +808,6 @@ static const struct nand_op_parser anfc_op_parser = NAND_OP_PARSER(
 		NAND_OP_PARSER_PAT_WAITRDY_ELEM(false)),
 	);
 
-static int anfc_select_target(struct nand_chip *chip, int target)
-{
-	struct anand *anand = to_anand(chip);
-	struct arasan_nfc *nfc = to_anfc(chip->controller);
-	int ret;
-
-	/* Update the controller timings and the potential ECC configuration */
-	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
-
-	/* Update clock frequency */
-	if (nfc->cur_clk != anand->clk) {
-		clk_disable_unprepare(nfc->controller_clk);
-		ret = clk_set_rate(nfc->controller_clk, anand->clk);
-		if (ret) {
-			dev_err(nfc->dev, "Failed to change clock rate\n");
-			return ret;
-		}
-
-		ret = clk_prepare_enable(nfc->controller_clk);
-		if (ret) {
-			dev_err(nfc->dev,
-				"Failed to re-enable the controller clock\n");
-			return ret;
-		}
-
-		nfc->cur_clk = anand->clk;
-	}
-
-	return 0;
-}
-
 static int anfc_check_op(struct nand_chip *chip,
 			 const struct nand_operation *op)
 {
@@ -1007,8 +1031,8 @@ static int anfc_init_hw_ecc_controller(struct arasan_nfc *nfc,
 	if (!anand->bch)
 		return -EINVAL;
 
-	ecc->read_page = anfc_read_page_hw_ecc;
-	ecc->write_page = anfc_write_page_hw_ecc;
+	ecc->read_page = anfc_sel_read_page_hw_ecc;
+	ecc->write_page = anfc_sel_write_page_hw_ecc;
 
 	return 0;
 }
-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
  2021-05-10 10:40 ` Miquel Raynal
@ 2021-05-10 10:40   ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.

The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/arasan-nand-controller.c | 148 +++++++++++++++---
 1 file changed, 125 insertions(+), 23 deletions(-)

diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 390f8d719c25..fb72e83595b4 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -15,6 +15,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
+#include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
@@ -107,6 +108,8 @@
 #define ANFC_XLNX_SDR_DFLT_CORE_CLK	100000000
 #define ANFC_XLNX_SDR_HS_CORE_CLK	80000000
 
+static struct gpio_desc *anfc_default_cs_array[2] = {NULL, NULL};
+
 /**
  * struct anfc_op - Defines how to execute an operation
  * @pkt_reg: Packet register
@@ -137,7 +140,6 @@ struct anfc_op {
  * struct anand - Defines the NAND chip related information
  * @node:		Used to store NAND chips into a list
  * @chip:		NAND chip information structure
- * @cs:			Chip select line
  * @rb:			Ready-busy line
  * @page_sz:		Register value of the page_sz field to use
  * @clk:		Expected clock frequency to use
@@ -151,11 +153,13 @@ struct anfc_op {
  * @errloc:		Array of errors located with soft BCH
  * @hw_ecc:		Buffer to store syndromes computed by hardware
  * @bch:		BCH structure
+ * @cs_idx:		Array of chip-select for this device, values are indexes
+ *			of the controller structure @gpio_cs array
+ * @ncs_idx:		Size of the @cs_idx array
  */
 struct anand {
 	struct list_head node;
 	struct nand_chip chip;
-	unsigned int cs;
 	unsigned int rb;
 	unsigned int page_sz;
 	unsigned long clk;
@@ -169,6 +173,8 @@ struct anand {
 	unsigned int *errloc;
 	u8 *hw_ecc;
 	struct bch_control *bch;
+	int *cs_idx;
+	int ncs_idx;
 };
 
 /**
@@ -179,8 +185,14 @@ struct anand {
  * @bus_clk:		Pointer to the flash clock
  * @controller:		Base controller structure
  * @chips:		List of all NAND chips attached to the controller
- * @assigned_cs:	Bitmask describing already assigned CS lines
  * @cur_clk:		Current clock rate
+ * @cs_array:		CS array. Native CS are left empty, the other cells are
+ *			populated with their corresponding GPIO descriptor.
+ * @ncs:		Size of @cs_array
+ * @cur_cs:		Index in @cs_array of the currently in use CS
+ * @native_cs:		Currently selected native CS
+ * @spare_cs:		Native CS that is not wired (may be selected when a GPIO
+ *			CS is in use)
  */
 struct arasan_nfc {
 	struct device *dev;
@@ -189,8 +201,12 @@ struct arasan_nfc {
 	struct clk *bus_clk;
 	struct nand_controller controller;
 	struct list_head chips;
-	unsigned long assigned_cs;
 	unsigned int cur_clk;
+	struct gpio_desc **cs_array;
+	unsigned int ncs;
+	int cur_cs;
+	unsigned int native_cs;
+	unsigned int spare_cs;
 };
 
 static struct anand *to_anand(struct nand_chip *nand)
@@ -273,12 +289,46 @@ static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
 	return 0;
 }
 
+static bool anfc_is_gpio_cs(struct arasan_nfc *nfc, int nfc_cs)
+{
+	return nfc_cs >= 0 && nfc->cs_array[nfc_cs];
+}
+
+static int anfc_relative_to_absolute_cs(struct anand *anand, int num)
+{
+	return anand->cs_idx[num];
+}
+
+static void anfc_assert_cs(struct arasan_nfc *nfc, unsigned int nfc_cs_idx)
+{
+	/* CS did not change: do nothing */
+	if (nfc->cur_cs == nfc_cs_idx)
+		return;
+
+	/* Deassert the previous CS if it was a GPIO */
+	if (anfc_is_gpio_cs(nfc, nfc->cur_cs))
+		gpiod_set_value_cansleep(nfc->cs_array[nfc->cur_cs], 1);
+
+	/* Assert the new one */
+	if (anfc_is_gpio_cs(nfc, nfc_cs_idx)) {
+		nfc->native_cs = nfc->spare_cs;
+		gpiod_set_value_cansleep(nfc->cs_array[nfc_cs_idx], 0);
+	} else {
+		nfc->native_cs = nfc_cs_idx;
+	}
+
+	nfc->cur_cs = nfc_cs_idx;
+}
+
 static int anfc_select_target(struct nand_chip *chip, int target)
 {
 	struct anand *anand = to_anand(chip);
 	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	unsigned int nfc_cs_idx = anfc_relative_to_absolute_cs(anand, target);
 	int ret;
 
+	anfc_assert_cs(nfc, nfc_cs_idx);
+
 	/* Update the controller timings and the potential ECC configuration */
 	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
 
@@ -346,7 +396,7 @@ static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
 		.addr2_reg =
 			((page >> 16) & 0xFF) |
 			ADDR2_STRENGTH(anand->strength) |
-			ADDR2_CS(anand->cs),
+			ADDR2_CS(nfc->native_cs),
 		.cmd_reg =
 			CMD_1(NAND_CMD_READ0) |
 			CMD_2(NAND_CMD_READSTART) |
@@ -463,7 +513,7 @@ static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 		.addr2_reg =
 			((page >> 16) & 0xFF) |
 			ADDR2_STRENGTH(anand->strength) |
-			ADDR2_CS(anand->cs),
+			ADDR2_CS(nfc->native_cs),
 		.cmd_reg =
 			CMD_1(NAND_CMD_SEQIN) |
 			CMD_2(NAND_CMD_PAGEPROG) |
@@ -521,6 +571,7 @@ static int anfc_parse_instructions(struct nand_chip *chip,
 				   const struct nand_subop *subop,
 				   struct anfc_op *nfc_op)
 {
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
 	struct anand *anand = to_anand(chip);
 	const struct nand_op_instr *instr = NULL;
 	bool first_cmd = true;
@@ -528,7 +579,7 @@ static int anfc_parse_instructions(struct nand_chip *chip,
 	int ret, i;
 
 	memset(nfc_op, 0, sizeof(*nfc_op));
-	nfc_op->addr2_reg = ADDR2_CS(anand->cs);
+	nfc_op->addr2_reg = ADDR2_CS(nfc->native_cs);
 	nfc_op->cmd_reg = CMD_PAGE_SIZE(anand->page_sz);
 
 	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
@@ -1118,37 +1169,43 @@ static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
 	struct anand *anand;
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
-	int cs, rb, ret;
+	int rb, ret, i;
 
 	anand = devm_kzalloc(nfc->dev, sizeof(*anand), GFP_KERNEL);
 	if (!anand)
 		return -ENOMEM;
 
-	/* We do not support multiple CS per chip yet */
-	if (of_property_count_elems_of_size(np, "reg", sizeof(u32)) != 1) {
+	/* Chip-select init */
+	anand->ncs_idx = of_property_count_elems_of_size(np, "reg", sizeof(u32));
+	if (anand->ncs_idx <= 0 || anand->ncs_idx > nfc->ncs) {
 		dev_err(nfc->dev, "Invalid reg property\n");
 		return -EINVAL;
 	}
 
-	ret = of_property_read_u32(np, "reg", &cs);
-	if (ret)
-		return ret;
+	anand->cs_idx = devm_kcalloc(nfc->dev, anand->ncs_idx,
+				     sizeof(*anand->cs_idx), GFP_KERNEL);
+	if (!anand->cs_idx)
+		return -ENOMEM;
 
+	for (i = 0; i < anand->ncs_idx; i++) {
+		ret = of_property_read_u32_index(np, "reg", i,
+						 &anand->cs_idx[i]);
+		if (ret) {
+			dev_err(nfc->dev, "invalid CS property: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/* Ready-busy init */
 	ret = of_property_read_u32(np, "nand-rb", &rb);
 	if (ret)
 		return ret;
 
-	if (cs >= ANFC_MAX_CS || rb >= ANFC_MAX_CS) {
-		dev_err(nfc->dev, "Wrong CS %d or RB %d\n", cs, rb);
+	if (rb >= ANFC_MAX_CS) {
+		dev_err(nfc->dev, "Wrong RB %d\n", rb);
 		return -EINVAL;
 	}
 
-	if (test_and_set_bit(cs, &nfc->assigned_cs)) {
-		dev_err(nfc->dev, "Already assigned CS %d\n", cs);
-		return -EINVAL;
-	}
-
-	anand->cs = cs;
 	anand->rb = rb;
 
 	chip = &anand->chip;
@@ -1164,7 +1221,7 @@ static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
 		return -EINVAL;
 	}
 
-	ret = nand_scan(chip, 1);
+	ret = nand_scan(chip, anand->ncs_idx);
 	if (ret) {
 		dev_err(nfc->dev, "Scan operation failed\n");
 		return ret;
@@ -1202,7 +1259,7 @@ static int anfc_chips_init(struct arasan_nfc *nfc)
 	int nchips = of_get_child_count(np);
 	int ret;
 
-	if (!nchips || nchips > ANFC_MAX_CS) {
+	if (!nchips) {
 		dev_err(nfc->dev, "Incorrect number of NAND chips (%d)\n",
 			nchips);
 		return -EINVAL;
@@ -1227,6 +1284,47 @@ static void anfc_reset(struct arasan_nfc *nfc)
 
 	/* Enable interrupt status */
 	writel_relaxed(EVENT_MASK, nfc->base + INTR_STS_EN_REG);
+
+	nfc->cur_cs = -1;
+}
+
+static int anfc_parse_cs(struct arasan_nfc *nfc)
+{
+	int ret;
+
+	/* Check the gpio-cs property */
+	ret = rawnand_dt_parse_gpio_cs(nfc->dev, &nfc->cs_array, &nfc->ncs);
+	if (ret)
+		return ret;
+
+	/*
+	 * The controller native CS cannot be both disabled at the same time.
+	 * Hence, only one native CS can be used if GPIO CS are needed, so that
+	 * the other is selected when a non-native CS must be asserted (not
+	 * wired physically or configured as GPIO instead of NAND CS). In this
+	 * case, the "not" chosen CS is assigned to nfc->spare_cs and selected
+	 * whenever a GPIO CS must be asserted.
+	 */
+	if (nfc->cs_array && nfc->ncs > 2) {
+		if (!nfc->cs_array[0] && !nfc->cs_array[1]) {
+			dev_err(nfc->dev,
+				"Assign a single native CS when using GPIOs\n");
+			return -EINVAL;
+		}
+
+		if (nfc->cs_array[0])
+			nfc->spare_cs = 0;
+		else
+			nfc->spare_cs = 1;
+	}
+
+	if (!nfc->cs_array) {
+		nfc->cs_array = anfc_default_cs_array;
+		nfc->ncs = ANFC_MAX_CS;
+		return 0;
+	}
+
+	return 0;
 }
 
 static int anfc_probe(struct platform_device *pdev)
@@ -1265,6 +1363,10 @@ static int anfc_probe(struct platform_device *pdev)
 	if (ret)
 		goto disable_controller_clk;
 
+	ret = anfc_parse_cs(nfc);
+	if (ret)
+		goto disable_bus_clk;
+
 	ret = anfc_chips_init(nfc);
 	if (ret)
 		goto disable_bus_clk;
-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
@ 2021-05-10 10:40   ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 10:40 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.

The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
---
 drivers/mtd/nand/raw/arasan-nand-controller.c | 148 +++++++++++++++---
 1 file changed, 125 insertions(+), 23 deletions(-)

diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 390f8d719c25..fb72e83595b4 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -15,6 +15,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dma-mapping.h>
+#include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
@@ -107,6 +108,8 @@
 #define ANFC_XLNX_SDR_DFLT_CORE_CLK	100000000
 #define ANFC_XLNX_SDR_HS_CORE_CLK	80000000
 
+static struct gpio_desc *anfc_default_cs_array[2] = {NULL, NULL};
+
 /**
  * struct anfc_op - Defines how to execute an operation
  * @pkt_reg: Packet register
@@ -137,7 +140,6 @@ struct anfc_op {
  * struct anand - Defines the NAND chip related information
  * @node:		Used to store NAND chips into a list
  * @chip:		NAND chip information structure
- * @cs:			Chip select line
  * @rb:			Ready-busy line
  * @page_sz:		Register value of the page_sz field to use
  * @clk:		Expected clock frequency to use
@@ -151,11 +153,13 @@ struct anfc_op {
  * @errloc:		Array of errors located with soft BCH
  * @hw_ecc:		Buffer to store syndromes computed by hardware
  * @bch:		BCH structure
+ * @cs_idx:		Array of chip-select for this device, values are indexes
+ *			of the controller structure @gpio_cs array
+ * @ncs_idx:		Size of the @cs_idx array
  */
 struct anand {
 	struct list_head node;
 	struct nand_chip chip;
-	unsigned int cs;
 	unsigned int rb;
 	unsigned int page_sz;
 	unsigned long clk;
@@ -169,6 +173,8 @@ struct anand {
 	unsigned int *errloc;
 	u8 *hw_ecc;
 	struct bch_control *bch;
+	int *cs_idx;
+	int ncs_idx;
 };
 
 /**
@@ -179,8 +185,14 @@ struct anand {
  * @bus_clk:		Pointer to the flash clock
  * @controller:		Base controller structure
  * @chips:		List of all NAND chips attached to the controller
- * @assigned_cs:	Bitmask describing already assigned CS lines
  * @cur_clk:		Current clock rate
+ * @cs_array:		CS array. Native CS are left empty, the other cells are
+ *			populated with their corresponding GPIO descriptor.
+ * @ncs:		Size of @cs_array
+ * @cur_cs:		Index in @cs_array of the currently in use CS
+ * @native_cs:		Currently selected native CS
+ * @spare_cs:		Native CS that is not wired (may be selected when a GPIO
+ *			CS is in use)
  */
 struct arasan_nfc {
 	struct device *dev;
@@ -189,8 +201,12 @@ struct arasan_nfc {
 	struct clk *bus_clk;
 	struct nand_controller controller;
 	struct list_head chips;
-	unsigned long assigned_cs;
 	unsigned int cur_clk;
+	struct gpio_desc **cs_array;
+	unsigned int ncs;
+	int cur_cs;
+	unsigned int native_cs;
+	unsigned int spare_cs;
 };
 
 static struct anand *to_anand(struct nand_chip *nand)
@@ -273,12 +289,46 @@ static int anfc_pkt_len_config(unsigned int len, unsigned int *steps,
 	return 0;
 }
 
+static bool anfc_is_gpio_cs(struct arasan_nfc *nfc, int nfc_cs)
+{
+	return nfc_cs >= 0 && nfc->cs_array[nfc_cs];
+}
+
+static int anfc_relative_to_absolute_cs(struct anand *anand, int num)
+{
+	return anand->cs_idx[num];
+}
+
+static void anfc_assert_cs(struct arasan_nfc *nfc, unsigned int nfc_cs_idx)
+{
+	/* CS did not change: do nothing */
+	if (nfc->cur_cs == nfc_cs_idx)
+		return;
+
+	/* Deassert the previous CS if it was a GPIO */
+	if (anfc_is_gpio_cs(nfc, nfc->cur_cs))
+		gpiod_set_value_cansleep(nfc->cs_array[nfc->cur_cs], 1);
+
+	/* Assert the new one */
+	if (anfc_is_gpio_cs(nfc, nfc_cs_idx)) {
+		nfc->native_cs = nfc->spare_cs;
+		gpiod_set_value_cansleep(nfc->cs_array[nfc_cs_idx], 0);
+	} else {
+		nfc->native_cs = nfc_cs_idx;
+	}
+
+	nfc->cur_cs = nfc_cs_idx;
+}
+
 static int anfc_select_target(struct nand_chip *chip, int target)
 {
 	struct anand *anand = to_anand(chip);
 	struct arasan_nfc *nfc = to_anfc(chip->controller);
+	unsigned int nfc_cs_idx = anfc_relative_to_absolute_cs(anand, target);
 	int ret;
 
+	anfc_assert_cs(nfc, nfc_cs_idx);
+
 	/* Update the controller timings and the potential ECC configuration */
 	writel_relaxed(anand->timings, nfc->base + DATA_INTERFACE_REG);
 
@@ -346,7 +396,7 @@ static int anfc_read_page_hw_ecc(struct nand_chip *chip, u8 *buf,
 		.addr2_reg =
 			((page >> 16) & 0xFF) |
 			ADDR2_STRENGTH(anand->strength) |
-			ADDR2_CS(anand->cs),
+			ADDR2_CS(nfc->native_cs),
 		.cmd_reg =
 			CMD_1(NAND_CMD_READ0) |
 			CMD_2(NAND_CMD_READSTART) |
@@ -463,7 +513,7 @@ static int anfc_write_page_hw_ecc(struct nand_chip *chip, const u8 *buf,
 		.addr2_reg =
 			((page >> 16) & 0xFF) |
 			ADDR2_STRENGTH(anand->strength) |
-			ADDR2_CS(anand->cs),
+			ADDR2_CS(nfc->native_cs),
 		.cmd_reg =
 			CMD_1(NAND_CMD_SEQIN) |
 			CMD_2(NAND_CMD_PAGEPROG) |
@@ -521,6 +571,7 @@ static int anfc_parse_instructions(struct nand_chip *chip,
 				   const struct nand_subop *subop,
 				   struct anfc_op *nfc_op)
 {
+	struct arasan_nfc *nfc = to_anfc(chip->controller);
 	struct anand *anand = to_anand(chip);
 	const struct nand_op_instr *instr = NULL;
 	bool first_cmd = true;
@@ -528,7 +579,7 @@ static int anfc_parse_instructions(struct nand_chip *chip,
 	int ret, i;
 
 	memset(nfc_op, 0, sizeof(*nfc_op));
-	nfc_op->addr2_reg = ADDR2_CS(anand->cs);
+	nfc_op->addr2_reg = ADDR2_CS(nfc->native_cs);
 	nfc_op->cmd_reg = CMD_PAGE_SIZE(anand->page_sz);
 
 	for (op_id = 0; op_id < subop->ninstrs; op_id++) {
@@ -1118,37 +1169,43 @@ static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
 	struct anand *anand;
 	struct nand_chip *chip;
 	struct mtd_info *mtd;
-	int cs, rb, ret;
+	int rb, ret, i;
 
 	anand = devm_kzalloc(nfc->dev, sizeof(*anand), GFP_KERNEL);
 	if (!anand)
 		return -ENOMEM;
 
-	/* We do not support multiple CS per chip yet */
-	if (of_property_count_elems_of_size(np, "reg", sizeof(u32)) != 1) {
+	/* Chip-select init */
+	anand->ncs_idx = of_property_count_elems_of_size(np, "reg", sizeof(u32));
+	if (anand->ncs_idx <= 0 || anand->ncs_idx > nfc->ncs) {
 		dev_err(nfc->dev, "Invalid reg property\n");
 		return -EINVAL;
 	}
 
-	ret = of_property_read_u32(np, "reg", &cs);
-	if (ret)
-		return ret;
+	anand->cs_idx = devm_kcalloc(nfc->dev, anand->ncs_idx,
+				     sizeof(*anand->cs_idx), GFP_KERNEL);
+	if (!anand->cs_idx)
+		return -ENOMEM;
 
+	for (i = 0; i < anand->ncs_idx; i++) {
+		ret = of_property_read_u32_index(np, "reg", i,
+						 &anand->cs_idx[i]);
+		if (ret) {
+			dev_err(nfc->dev, "invalid CS property: %d\n", ret);
+			return ret;
+		}
+	}
+
+	/* Ready-busy init */
 	ret = of_property_read_u32(np, "nand-rb", &rb);
 	if (ret)
 		return ret;
 
-	if (cs >= ANFC_MAX_CS || rb >= ANFC_MAX_CS) {
-		dev_err(nfc->dev, "Wrong CS %d or RB %d\n", cs, rb);
+	if (rb >= ANFC_MAX_CS) {
+		dev_err(nfc->dev, "Wrong RB %d\n", rb);
 		return -EINVAL;
 	}
 
-	if (test_and_set_bit(cs, &nfc->assigned_cs)) {
-		dev_err(nfc->dev, "Already assigned CS %d\n", cs);
-		return -EINVAL;
-	}
-
-	anand->cs = cs;
 	anand->rb = rb;
 
 	chip = &anand->chip;
@@ -1164,7 +1221,7 @@ static int anfc_chip_init(struct arasan_nfc *nfc, struct device_node *np)
 		return -EINVAL;
 	}
 
-	ret = nand_scan(chip, 1);
+	ret = nand_scan(chip, anand->ncs_idx);
 	if (ret) {
 		dev_err(nfc->dev, "Scan operation failed\n");
 		return ret;
@@ -1202,7 +1259,7 @@ static int anfc_chips_init(struct arasan_nfc *nfc)
 	int nchips = of_get_child_count(np);
 	int ret;
 
-	if (!nchips || nchips > ANFC_MAX_CS) {
+	if (!nchips) {
 		dev_err(nfc->dev, "Incorrect number of NAND chips (%d)\n",
 			nchips);
 		return -EINVAL;
@@ -1227,6 +1284,47 @@ static void anfc_reset(struct arasan_nfc *nfc)
 
 	/* Enable interrupt status */
 	writel_relaxed(EVENT_MASK, nfc->base + INTR_STS_EN_REG);
+
+	nfc->cur_cs = -1;
+}
+
+static int anfc_parse_cs(struct arasan_nfc *nfc)
+{
+	int ret;
+
+	/* Check the gpio-cs property */
+	ret = rawnand_dt_parse_gpio_cs(nfc->dev, &nfc->cs_array, &nfc->ncs);
+	if (ret)
+		return ret;
+
+	/*
+	 * The controller native CS cannot be both disabled at the same time.
+	 * Hence, only one native CS can be used if GPIO CS are needed, so that
+	 * the other is selected when a non-native CS must be asserted (not
+	 * wired physically or configured as GPIO instead of NAND CS). In this
+	 * case, the "not" chosen CS is assigned to nfc->spare_cs and selected
+	 * whenever a GPIO CS must be asserted.
+	 */
+	if (nfc->cs_array && nfc->ncs > 2) {
+		if (!nfc->cs_array[0] && !nfc->cs_array[1]) {
+			dev_err(nfc->dev,
+				"Assign a single native CS when using GPIOs\n");
+			return -EINVAL;
+		}
+
+		if (nfc->cs_array[0])
+			nfc->spare_cs = 0;
+		else
+			nfc->spare_cs = 1;
+	}
+
+	if (!nfc->cs_array) {
+		nfc->cs_array = anfc_default_cs_array;
+		nfc->ncs = ANFC_MAX_CS;
+		return 0;
+	}
+
+	return 0;
 }
 
 static int anfc_probe(struct platform_device *pdev)
@@ -1265,6 +1363,10 @@ static int anfc_probe(struct platform_device *pdev)
 	if (ret)
 		goto disable_controller_clk;
 
+	ret = anfc_parse_cs(nfc);
+	if (ret)
+		goto disable_bus_clk;
+
 	ret = anfc_chips_init(nfc);
 	if (ret)
 		goto disable_bus_clk;
-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-10 16:00     ` kernel test robot
  -1 siblings, 0 replies; 30+ messages in thread
From: kernel test robot @ 2021-05-10 16:00 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: kbuild-all, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]

Hi Miquel,

I love your patch! Yet something to improve:

[auto build test ERROR on mtd/nand/next]
[also build test ERROR on mtd/mtd/next v5.13-rc1 next-20210510]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Miquel-Raynal/Bring-GPIO-CS-support-to-the-Arasan-controller-driver/20210510-184335
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next
config: i386-randconfig-a014-20210510 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-22) 9.3.0
reproduce (this is a W=1 build):
        # https://github.com/0day-ci/linux/commit/09c3e51f9529c4773d8a5999e34cf241de5a5dda
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Miquel-Raynal/Bring-GPIO-CS-support-to-the-Arasan-controller-driver/20210510-184335
        git checkout 09c3e51f9529c4773d8a5999e34cf241de5a5dda
        # save the attached .config to linux build tree
        make W=1 W=1 ARCH=i386 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>, old ones prefixed by <<):

>> ERROR: modpost: "rawnand_dt_parse_gpio_cs" [drivers/mtd/nand/raw/arasan-nand-controller.ko] undefined!

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 31156 bytes --]

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
@ 2021-05-10 16:00     ` kernel test robot
  0 siblings, 0 replies; 30+ messages in thread
From: kernel test robot @ 2021-05-10 16:00 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: kbuild-all, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

[-- Attachment #1: Type: text/plain, Size: 1526 bytes --]

Hi Miquel,

I love your patch! Yet something to improve:

[auto build test ERROR on mtd/nand/next]
[also build test ERROR on mtd/mtd/next v5.13-rc1 next-20210510]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Miquel-Raynal/Bring-GPIO-CS-support-to-the-Arasan-controller-driver/20210510-184335
base:   https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next
config: i386-randconfig-a014-20210510 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-22) 9.3.0
reproduce (this is a W=1 build):
        # https://github.com/0day-ci/linux/commit/09c3e51f9529c4773d8a5999e34cf241de5a5dda
        git remote add linux-review https://github.com/0day-ci/linux
        git fetch --no-tags linux-review Miquel-Raynal/Bring-GPIO-CS-support-to-the-Arasan-controller-driver/20210510-184335
        git checkout 09c3e51f9529c4773d8a5999e34cf241de5a5dda
        # save the attached .config to linux build tree
        make W=1 W=1 ARCH=i386 

If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <lkp@intel.com>

All errors (new ones prefixed by >>, old ones prefixed by <<):

>> ERROR: modpost: "rawnand_dt_parse_gpio_cs" [drivers/mtd/nand/raw/arasan-nand-controller.ko] undefined!

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all@lists.01.org

[-- Attachment #2: .config.gz --]
[-- Type: application/gzip, Size: 31156 bytes --]

[-- Attachment #3: Type: text/plain, Size: 144 bytes --]

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-10 16:51     ` Rob Herring
  -1 siblings, 0 replies; 30+ messages in thread
From: Rob Herring @ 2021-05-10 16:51 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: devicetree, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, May 10, 2021 at 12:40:47PM +0200, Miquel Raynal wrote:
> To reach higher capacities, arrays of chips are now pretty common.
> Unfortunately, most of the controllers have been designed a decade ago
> and did not all anticipate the need for several chip-selects. The new
> cs-gpios property allows to workaround this limitation by adding as many
> GPIO chip-select as needed.

Subject and example have wrong property name.

> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> index 678b39952502..70a400e385b2 100644
> --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> @@ -38,6 +38,15 @@ properties:
>  
>    ranges: true
>  
> +  cs-gpios:
> +    description:
> +      Array of chip-select available to the controller. The first
> +      entries are a 1:1 mapping of the available chip-select on the
> +      NAND controller (even if they are not used). As many additional
> +      chip-select as needed may follow and should be phandles of GPIO
> +      lines. 'reg' entries of the NAND chip subnodes become indexes of
> +      this array when this property is present.

Can we put some 'maxItems' value here. I want to make the meta-schema 
enforce that. I realize there's not really one here, but a 'should be 
enough' value is fine. We can bump it up if needed.

> +
>  patternProperties:
>    "^nand@[a-f0-9]$":
>      type: object
> @@ -164,14 +173,19 @@ examples:
>      nand-controller {
>        #address-cells = <1>;
>        #size-cells = <0>;
> +      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
>  
>        /* controller specific properties */
>  
>        nand@0 {
> -        reg = <0>;
> +        reg = <0>; /* Native CS */
>          nand-use-soft-ecc-engine;
>          nand-ecc-algo = "bch";
>  
>          /* controller specific properties */
>        };
> +
> +      nand@1 {
> +        reg = <1>; /* GPIO CS */
> +      };
>      };
> -- 
> 2.27.0
> 

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
@ 2021-05-10 16:51     ` Rob Herring
  0 siblings, 0 replies; 30+ messages in thread
From: Rob Herring @ 2021-05-10 16:51 UTC (permalink / raw)
  To: Miquel Raynal
  Cc: devicetree, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, May 10, 2021 at 12:40:47PM +0200, Miquel Raynal wrote:
> To reach higher capacities, arrays of chips are now pretty common.
> Unfortunately, most of the controllers have been designed a decade ago
> and did not all anticipate the need for several chip-selects. The new
> cs-gpios property allows to workaround this limitation by adding as many
> GPIO chip-select as needed.

Subject and example have wrong property name.

> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> ---
>  .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
>  1 file changed, 15 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> index 678b39952502..70a400e385b2 100644
> --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> @@ -38,6 +38,15 @@ properties:
>  
>    ranges: true
>  
> +  cs-gpios:
> +    description:
> +      Array of chip-select available to the controller. The first
> +      entries are a 1:1 mapping of the available chip-select on the
> +      NAND controller (even if they are not used). As many additional
> +      chip-select as needed may follow and should be phandles of GPIO
> +      lines. 'reg' entries of the NAND chip subnodes become indexes of
> +      this array when this property is present.

Can we put some 'maxItems' value here. I want to make the meta-schema 
enforce that. I realize there's not really one here, but a 'should be 
enough' value is fine. We can bump it up if needed.

> +
>  patternProperties:
>    "^nand@[a-f0-9]$":
>      type: object
> @@ -164,14 +173,19 @@ examples:
>      nand-controller {
>        #address-cells = <1>;
>        #size-cells = <0>;
> +      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
>  
>        /* controller specific properties */
>  
>        nand@0 {
> -        reg = <0>;
> +        reg = <0>; /* Native CS */
>          nand-use-soft-ecc-engine;
>          nand-ecc-algo = "bch";
>  
>          /* controller specific properties */
>        };
> +
> +      nand@1 {
> +        reg = <1>; /* GPIO CS */
> +      };
>      };
> -- 
> 2.27.0
> 

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
  2021-05-10 16:51     ` Rob Herring
@ 2021-05-10 17:00       ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 17:00 UTC (permalink / raw)
  To: Rob Herring
  Cc: devicetree, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

Hi Rob,

Rob Herring <robh@kernel.org> wrote on Mon, 10 May 2021 11:51:25 -0500:

> On Mon, May 10, 2021 at 12:40:47PM +0200, Miquel Raynal wrote:
> > To reach higher capacities, arrays of chips are now pretty common.
> > Unfortunately, most of the controllers have been designed a decade ago
> > and did not all anticipate the need for several chip-selects. The new
> > cs-gpios property allows to workaround this limitation by adding as many
> > GPIO chip-select as needed.  
> 
> Subject and example have wrong property name.

True.

> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > ---
> >  .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
> >  1 file changed, 15 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > index 678b39952502..70a400e385b2 100644
> > --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > @@ -38,6 +38,15 @@ properties:
> >  
> >    ranges: true
> >  
> > +  cs-gpios:
> > +    description:
> > +      Array of chip-select available to the controller. The first
> > +      entries are a 1:1 mapping of the available chip-select on the
> > +      NAND controller (even if they are not used). As many additional
> > +      chip-select as needed may follow and should be phandles of GPIO
> > +      lines. 'reg' entries of the NAND chip subnodes become indexes of
> > +      this array when this property is present.  
> 
> Can we put some 'maxItems' value here. I want to make the meta-schema 
> enforce that. I realize there's not really one here, but a 'should be 
> enough' value is fine. We can bump it up if needed.

Ok, I already have an example with 8 entries, we can set maxItems to 8
and see how it goes.

Please ignore v3 which was sent to fix another unrelated issue, at the
same time you reviewed v2.

> > +
> >  patternProperties:
> >    "^nand@[a-f0-9]$":
> >      type: object
> > @@ -164,14 +173,19 @@ examples:
> >      nand-controller {
> >        #address-cells = <1>;
> >        #size-cells = <0>;
> > +      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
> >  
> >        /* controller specific properties */
> >  
> >        nand@0 {
> > -        reg = <0>;
> > +        reg = <0>; /* Native CS */
> >          nand-use-soft-ecc-engine;
> >          nand-ecc-algo = "bch";
> >  
> >          /* controller specific properties */
> >        };
> > +
> > +      nand@1 {
> > +        reg = <1>; /* GPIO CS */
> > +      };
> >      };
> > -- 
> > 2.27.0
> >   

Thanks,
Miquèl

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property
@ 2021-05-10 17:00       ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 17:00 UTC (permalink / raw)
  To: Rob Herring
  Cc: devicetree, Richard Weinberger, Vignesh Raghavendra,
	Tudor Ambarus, linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

Hi Rob,

Rob Herring <robh@kernel.org> wrote on Mon, 10 May 2021 11:51:25 -0500:

> On Mon, May 10, 2021 at 12:40:47PM +0200, Miquel Raynal wrote:
> > To reach higher capacities, arrays of chips are now pretty common.
> > Unfortunately, most of the controllers have been designed a decade ago
> > and did not all anticipate the need for several chip-selects. The new
> > cs-gpios property allows to workaround this limitation by adding as many
> > GPIO chip-select as needed.  
> 
> Subject and example have wrong property name.

True.

> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> > ---
> >  .../devicetree/bindings/mtd/nand-controller.yaml | 16 +++++++++++++++-
> >  1 file changed, 15 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > index 678b39952502..70a400e385b2 100644
> > --- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > +++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
> > @@ -38,6 +38,15 @@ properties:
> >  
> >    ranges: true
> >  
> > +  cs-gpios:
> > +    description:
> > +      Array of chip-select available to the controller. The first
> > +      entries are a 1:1 mapping of the available chip-select on the
> > +      NAND controller (even if they are not used). As many additional
> > +      chip-select as needed may follow and should be phandles of GPIO
> > +      lines. 'reg' entries of the NAND chip subnodes become indexes of
> > +      this array when this property is present.  
> 
> Can we put some 'maxItems' value here. I want to make the meta-schema 
> enforce that. I realize there's not really one here, but a 'should be 
> enough' value is fine. We can bump it up if needed.

Ok, I already have an example with 8 entries, we can set maxItems to 8
and see how it goes.

Please ignore v3 which was sent to fix another unrelated issue, at the
same time you reviewed v2.

> > +
> >  patternProperties:
> >    "^nand@[a-f0-9]$":
> >      type: object
> > @@ -164,14 +173,19 @@ examples:
> >      nand-controller {
> >        #address-cells = <1>;
> >        #size-cells = <0>;
> > +      gpio-cs = <0>, <&gpioA 1>; /* A single native CS is available */
> >  
> >        /* controller specific properties */
> >  
> >        nand@0 {
> > -        reg = <0>;
> > +        reg = <0>; /* Native CS */
> >          nand-use-soft-ecc-engine;
> >          nand-ecc-algo = "bch";
> >  
> >          /* controller specific properties */
> >        };
> > +
> > +      nand@1 {
> > +        reg = <1>; /* GPIO CS */
> > +      };
> >      };
> > -- 
> > 2.27.0
> >   

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-26  9:03     ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:51 UTC, Miquel Raynal wrote:
> Make use of the cs-gpios DT property as well as the core helper to parse
> it so that the Arasan controller driver can now assert many more chips
> than natively.
> 
> The Arasan controller has an internal limitation: RB0 is tied to CS0 and
> RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
> as one or the other native CS is not used (or configured to be driven as
> a GPIO) and that all additional CS are physically wired on its
> corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
> as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
> CS. Then the target asserted by CS0 should also be wired to RB0, while
> the targets asserted by CS1 and CS2 should be wired to RB1.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> Reported-by: kernel test robot <lkp@intel.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS
@ 2021-05-26  9:03     ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:51 UTC, Miquel Raynal wrote:
> Make use of the cs-gpios DT property as well as the core helper to parse
> it so that the Arasan controller driver can now assert many more chips
> than natively.
> 
> The Arasan controller has an internal limitation: RB0 is tied to CS0 and
> RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
> as one or the other native CS is not used (or configured to be driven as
> a GPIO) and that all additional CS are physically wired on its
> corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
> as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
> CS. Then the target asserted by CS0 should also be wired to RB0, while
> the targets asserted by CS1 and CS2 should be wired to RB1.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> Reported-by: kernel test robot <lkp@intel.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 4/5] mtd: rawnand: arasan: Ensure proper configuration for the asserted target
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-26  9:03     ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:50 UTC, Miquel Raynal wrote:
> The controller being always asserting one CS or the other, there is no
> need to actually select the right target before doing a page read/write.
> However, the anfc_select_target() helper actually also changes the
> timing configuration and clock in the case were two different NAND chips
> with different timing requirements would be used. In this situation, we
> must ensure proper configuration of the controller by calling it.
> 
> As a consequence of this change, the anfc_select_target() helper is
> being moved earlier in the driver.
> 
> Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 4/5] mtd: rawnand: arasan: Ensure proper configuration for the asserted target
@ 2021-05-26  9:03     ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:50 UTC, Miquel Raynal wrote:
> The controller being always asserting one CS or the other, there is no
> need to actually select the right target before doing a page read/write.
> However, the anfc_select_target() helper actually also changes the
> timing configuration and clock in the case were two different NAND chips
> with different timing requirements would be used. In this situation, we
> must ensure proper configuration of the controller by calling it.
> 
> As a consequence of this change, the anfc_select_target() helper is
> being moved earlier in the driver.
> 
> Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 3/5] mtd: rawnand: Add a helper to parse the gpio-cs DT property
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-26  9:03     ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:49 UTC, Miquel Raynal wrote:
> New chips may feature a lot of CS because of their extended length. As
> many controllers have been designed a decade ago, they usually only
> feature just a couple. This does not mean that the entire range of
> these chips cannot be accessed: it is just a matter of adding more
> GPIO CS in the hardware design. A DT property has been added to
> describe the CS array: cs-gpios.
> 
> Here is the code parsing it this new property, allocating what needs to
> be, requesting the GPIOs and returning an array with the additional
> available CS. The first entries of this array are left empty and are
> reserved for native CS.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 3/5] mtd: rawnand: Add a helper to parse the gpio-cs DT property
@ 2021-05-26  9:03     ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:49 UTC, Miquel Raynal wrote:
> New chips may feature a lot of CS because of their extended length. As
> many controllers have been designed a decade ago, they usually only
> feature just a couple. This does not mean that the entire range of
> these chips cannot be accessed: it is just a matter of adding more
> GPIO CS in the hardware design. A DT property has been added to
> describe the CS array: cs-gpios.
> 
> Here is the code parsing it this new property, allocating what needs to
> be, requesting the GPIOs and returning an array with the additional
> available CS. The first entries of this array are left empty and are
> reserved for native CS.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
  2021-05-10 10:40   ` Miquel Raynal
@ 2021-05-26  9:03     ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:48 UTC, Miquel Raynal wrote:
> The struct gpio_desc is declared in the middle of the rawnand.h header,
> right before the first function using it (nand_gpio_waitrdy). Before
> adding a new function and to make it clear: move the declaration to the
> top of the file.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
@ 2021-05-26  9:03     ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:03 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

On Mon, 2021-05-10 at 10:40:48 UTC, Miquel Raynal wrote:
> The struct gpio_desc is declared in the middle of the rawnand.h header,
> right before the first function using it (nand_gpio_waitrdy). Before
> adding a new function and to make it clear: move the declaration to the
> top of the file.
> 
> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.

Miquel

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
  2021-05-26  9:03     ` Miquel Raynal
@ 2021-05-26  9:34       ` Miquel Raynal
  -1 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:34 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

Hi Miquel,

Miquel Raynal <miquel.raynal@bootlin.com> wrote on Wed, 26 May 2021
11:03:34 +0200:

> On Mon, 2021-05-10 at 10:40:48 UTC, Miquel Raynal wrote:
> > The struct gpio_desc is declared in the middle of the rawnand.h header,
> > right before the first function using it (nand_gpio_waitrdy). Before
> > adding a new function and to make it clear: move the declaration to the
> > top of the file.
> > 
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>  
> 
> Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.
> 
> Miquel

FYI, due to an error in the headers of this series, patchwork/lore got
confused between v2 and v3. This versions is not the one I should have
applied. I just dropped it, will resend v3 and apply it immediately.

Thanks,
Miquèl

^ permalink raw reply	[flat|nested] 30+ messages in thread

* Re: [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top
@ 2021-05-26  9:34       ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-26  9:34 UTC (permalink / raw)
  To: Miquel Raynal, Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni

Hi Miquel,

Miquel Raynal <miquel.raynal@bootlin.com> wrote on Wed, 26 May 2021
11:03:34 +0200:

> On Mon, 2021-05-10 at 10:40:48 UTC, Miquel Raynal wrote:
> > The struct gpio_desc is declared in the middle of the rawnand.h header,
> > right before the first function using it (nand_gpio_waitrdy). Before
> > adding a new function and to make it clear: move the declaration to the
> > top of the file.
> > 
> > Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>  
> 
> Applied to https://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux.git nand/next.
> 
> Miquel

FYI, due to an error in the headers of this series, patchwork/lore got
confused between v2 and v3. This versions is not the one I should have
applied. I just dropped it, will resend v3 and apply it immediately.

Thanks,
Miquèl

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver
@ 2021-05-10 16:31 ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 16:31 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Hello,

This is a short series bringing a useful feature for drivers which are a
little bit constrained regarding their number of native CS. As
manufacturer tend to group chips in arrays to enlarge the overall
available space, it might be useful to other controller drivers to make
use of the added DT property (cs-gpios) as well as the core helper which
is being introduced to parse this DT property and returned a CS array
with either empty cells (native CS are being used) or a GPIO descriptor
structure pointer (GPIO CS).

This is applied to the Arasan NAND controller driver which involved a
little bit more boilerplate than estimated I thought due to its internal
constraints regarding the bond between CS and RB.

Cheers,
Miquèl

Changes in v2:
* Added a missing MODULE_EXPORT() reported by kernel test robot.

Changes in v2:
* Rebased on top of v5.13-rc1
* This time I'm CC'ing Rob + DT ML...

Miquel Raynal (5):
  dt-binding: mtd: nand: Document gpio-cs property
  mtd: rawnand: Move struct gpio_desc declaration to the top
  mtd: rawnand: Add a helper to parse the gpio-cs DT property
  mtd: rawnand: arasan: Ensure proper configuration for the asserted
    target
  mtd: rawnand: arasan: Leverage additional GPIO CS

 .../bindings/mtd/nand-controller.yaml         |  16 +-
 drivers/mtd/nand/raw/arasan-nand-controller.c | 238 +++++++++++++-----
 drivers/mtd/nand/raw/nand_base.c              |  39 +++
 include/linux/mtd/rawnand.h                   |   6 +-
 4 files changed, 241 insertions(+), 58 deletions(-)

-- 
2.27.0


^ permalink raw reply	[flat|nested] 30+ messages in thread

* [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver
@ 2021-05-10 16:31 ` Miquel Raynal
  0 siblings, 0 replies; 30+ messages in thread
From: Miquel Raynal @ 2021-05-10 16:31 UTC (permalink / raw)
  To: Rob Herring, devicetree
  Cc: Richard Weinberger, Vignesh Raghavendra, Tudor Ambarus,
	linux-mtd, Naga Sureshkumar Relli, Michal Simek,
	Thomas Petazzoni, Miquel Raynal

Hello,

This is a short series bringing a useful feature for drivers which are a
little bit constrained regarding their number of native CS. As
manufacturer tend to group chips in arrays to enlarge the overall
available space, it might be useful to other controller drivers to make
use of the added DT property (cs-gpios) as well as the core helper which
is being introduced to parse this DT property and returned a CS array
with either empty cells (native CS are being used) or a GPIO descriptor
structure pointer (GPIO CS).

This is applied to the Arasan NAND controller driver which involved a
little bit more boilerplate than estimated I thought due to its internal
constraints regarding the bond between CS and RB.

Cheers,
Miquèl

Changes in v2:
* Added a missing MODULE_EXPORT() reported by kernel test robot.

Changes in v2:
* Rebased on top of v5.13-rc1
* This time I'm CC'ing Rob + DT ML...

Miquel Raynal (5):
  dt-binding: mtd: nand: Document gpio-cs property
  mtd: rawnand: Move struct gpio_desc declaration to the top
  mtd: rawnand: Add a helper to parse the gpio-cs DT property
  mtd: rawnand: arasan: Ensure proper configuration for the asserted
    target
  mtd: rawnand: arasan: Leverage additional GPIO CS

 .../bindings/mtd/nand-controller.yaml         |  16 +-
 drivers/mtd/nand/raw/arasan-nand-controller.c | 238 +++++++++++++-----
 drivers/mtd/nand/raw/nand_base.c              |  39 +++
 include/linux/mtd/rawnand.h                   |   6 +-
 4 files changed, 241 insertions(+), 58 deletions(-)

-- 
2.27.0


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

^ permalink raw reply	[flat|nested] 30+ messages in thread

end of thread, other threads:[~2021-05-26 11:42 UTC | newest]

Thread overview: 30+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-05-10 10:40 [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver Miquel Raynal
2021-05-10 10:40 ` Miquel Raynal
2021-05-10 10:40 ` [PATCH v2 1/5] dt-binding: mtd: nand: Document gpio-cs property Miquel Raynal
2021-05-10 10:40   ` Miquel Raynal
2021-05-10 16:51   ` Rob Herring
2021-05-10 16:51     ` Rob Herring
2021-05-10 17:00     ` Miquel Raynal
2021-05-10 17:00       ` Miquel Raynal
2021-05-10 10:40 ` [PATCH v2 2/5] mtd: rawnand: Move struct gpio_desc declaration to the top Miquel Raynal
2021-05-10 10:40   ` Miquel Raynal
2021-05-26  9:03   ` Miquel Raynal
2021-05-26  9:03     ` Miquel Raynal
2021-05-26  9:34     ` Miquel Raynal
2021-05-26  9:34       ` Miquel Raynal
2021-05-10 10:40 ` [PATCH v2 3/5] mtd: rawnand: Add a helper to parse the gpio-cs DT property Miquel Raynal
2021-05-10 10:40   ` Miquel Raynal
2021-05-26  9:03   ` Miquel Raynal
2021-05-26  9:03     ` Miquel Raynal
2021-05-10 10:40 ` [PATCH v2 4/5] mtd: rawnand: arasan: Ensure proper configuration for the asserted target Miquel Raynal
2021-05-10 10:40   ` Miquel Raynal
2021-05-26  9:03   ` Miquel Raynal
2021-05-26  9:03     ` Miquel Raynal
2021-05-10 10:40 ` [PATCH v2 5/5] mtd: rawnand: arasan: Leverage additional GPIO CS Miquel Raynal
2021-05-10 10:40   ` Miquel Raynal
2021-05-10 16:00   ` kernel test robot
2021-05-10 16:00     ` kernel test robot
2021-05-26  9:03   ` Miquel Raynal
2021-05-26  9:03     ` Miquel Raynal
2021-05-10 16:31 [PATCH v2 0/5] Bring GPIO CS support to the Arasan controller driver Miquel Raynal
2021-05-10 16:31 ` Miquel Raynal

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.