* [PATCH v3 2/4] arm64: dts: qcom: sm8250: Add SDHCI2 sleep mode pinctrl
2021-06-16 0:23 [PATCH v3 1/4] arm64: dts: qcom: sm8250: Disable Adreno and Venus by default Konrad Dybcio
@ 2021-06-16 0:23 ` Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 3/4] arm64: dts: qcom: sm8250: Move gpio.h inclusion to SoC DTSI Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 4/4] arm64: dts: qcom: Add support for SONY Xperia 1 II / 5 II (Edo platform) Konrad Dybcio
2 siblings, 0 replies; 4+ messages in thread
From: Konrad Dybcio @ 2021-06-16 0:23 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel
Add required pins for SDHCI2, so that the interface can work reliably.
This commit adds sleep_state setup to the SoC DTSI, as it is common for
all boards.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v2:
- Only add sleep_state to the SoC DTSI
arch/arm64/boot/dts/qcom/sm8250.dtsi | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index fc1049c2bb11..0b99f1d03c4a 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -3401,6 +3401,26 @@ ws {
output-high;
};
};
+
+ sdc2_sleep_state: sdc2-sleep {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc2_data";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
};
apps_smmu: iommu@15000000 {
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v3 3/4] arm64: dts: qcom: sm8250: Move gpio.h inclusion to SoC DTSI
2021-06-16 0:23 [PATCH v3 1/4] arm64: dts: qcom: sm8250: Disable Adreno and Venus by default Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 2/4] arm64: dts: qcom: sm8250: Add SDHCI2 sleep mode pinctrl Konrad Dybcio
@ 2021-06-16 0:23 ` Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 4/4] arm64: dts: qcom: Add support for SONY Xperia 1 II / 5 II (Edo platform) Konrad Dybcio
2 siblings, 0 replies; 4+ messages in thread
From: Konrad Dybcio @ 2021-06-16 0:23 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel, Kees Cook,
Anton Vorontsov, Colin Cross, Tony Luck
Almost any board that boots and has a way to interact with it
(say for the rare cases of just-pstore or let's-rely-on-bootloader-setup)
needs to set some GPIOs, so it makes no sense to include gpio.h separately
each time. Hence move it to SoC DTSI.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v2:
- Add this patch
arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 1 -
arch/arm64/boot/dts/qcom/sm8250-hdk.dts | 1 -
arch/arm64/boot/dts/qcom/sm8250.dtsi | 1 +
3 files changed, 1 insertion(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index a5b742325261..d5a4f5a27da6 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -5,7 +5,6 @@
/dts-v1/;
-#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/sound/qcom,q6asm.h>
diff --git a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
index 397359ee2f85..bc6f81254ef7 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
@@ -6,7 +6,6 @@
/dts-v1/;
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-#include <dt-bindings/gpio/gpio.h>
#include "sm8250.dtsi"
#include "pm8150.dtsi"
#include "pm8150b.dtsi"
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 0b99f1d03c4a..c8bb97ab6c17 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,gcc-sm8250.h>
#include <dt-bindings/clock/qcom,gpucc-sm8250.h>
#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sm8250.h>
#include <dt-bindings/mailbox/qcom-ipcc.h>
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH v3 4/4] arm64: dts: qcom: Add support for SONY Xperia 1 II / 5 II (Edo platform)
2021-06-16 0:23 [PATCH v3 1/4] arm64: dts: qcom: sm8250: Disable Adreno and Venus by default Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 2/4] arm64: dts: qcom: sm8250: Add SDHCI2 sleep mode pinctrl Konrad Dybcio
2021-06-16 0:23 ` [PATCH v3 3/4] arm64: dts: qcom: sm8250: Move gpio.h inclusion to SoC DTSI Konrad Dybcio
@ 2021-06-16 0:23 ` Konrad Dybcio
2 siblings, 0 replies; 4+ messages in thread
From: Konrad Dybcio @ 2021-06-16 0:23 UTC (permalink / raw)
To: ~postmarketos/upstreaming
Cc: martin.botka, angelogioacchino.delregno, marijn.suijten,
jamipkettunen, Konrad Dybcio, Andy Gross, Bjorn Andersson,
Rob Herring, linux-arm-msm, devicetree, linux-kernel, Kees Cook,
Anton Vorontsov, Colin Cross, Tony Luck
Add support for SONY Xperia 1 II and 5 II smartphones (read one/five mark two).
They are based on the Qualcomm SM8250 chipset and both feature 5G modems. There
also exists a third Edo board, namely the Xperia PRO (PDX204), but it's $2500
and no developers have obtained it so far (to my knowledge).
The devices are affected by a scary UFS behaviour where sending a certain UFS
command (which is worked around on downstream) renders the device unbootable,
by effectively erasing the bootloader. Therefore UFS AND UFSPHY are strictly
disabled for now.
Downstream workaround:
https://github.com/kholk/kernel/commit/2e7a9ee1c91a016baa0b826a7752ec45663a0561
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v2:
- Bring the SDC pins over here
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../qcom/sm8250-sony-xperia-edo-pdx203.dts | 15 +
.../qcom/sm8250-sony-xperia-edo-pdx206.dts | 24 +
.../boot/dts/qcom/sm8250-sony-xperia-edo.dtsi | 525 ++++++++++++++++++
4 files changed, 566 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
create mode 100644 arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
create mode 100644 arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 456502aeee49..a3b832d9fc0c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -73,5 +73,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx203.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx206.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb
dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
new file mode 100644
index 000000000000..79afeb07f4a2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx203.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sm8250-sony-xperia-edo.dtsi"
+
+/ {
+ model = "Sony Xperia 1 II";
+ compatible = "sony,pdx203-generic", "qcom,sm8250";
+};
+
+/delete-node/ &vreg_l7f_1p8;
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
new file mode 100644
index 000000000000..999b662f4679
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo-pdx206.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sm8250-sony-xperia-edo.dtsi"
+
+/ {
+ model = "Sony Xperia 5 II";
+ compatible = "sony,pdx206-generic", "qcom,sm8250";
+};
+
+&framebuffer {
+ width = <1080>;
+ height = <2520>;
+ stride = <(1080 * 4)>;
+};
+
+&vreg_l2f_1p3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
new file mode 100644
index 000000000000..0db63eb08c60
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8250.dtsi"
+#include "pm8150.dtsi"
+#include "pm8150b.dtsi"
+#include "pm8150l.dtsi"
+#include "pm8009.dtsi"
+
+/delete-node/ &adsp_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &cdsp_secure_heap;
+
+/ {
+ qcom,msm-id = <356 0x20001>; /* SM8250 v2.1 */
+ qcom,board-id = <0x10008 0>;
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer: framebuffer@9c000000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0x9c000000 0 0x2300000>;
+ width = <1644>;
+ height = <3840>;
+ stride = <(1644 * 4)>;
+ format = "a8r8g8b8";
+ /*
+ * That's a lot of clocks, but it's necessary due
+ * to unused clk cleanup & no panel driver yet..
+ */
+ clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+ <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
+ <&dispcc DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+ <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+ <&dispcc DISP_CC_MDSS_ESC0_CLK>;
+ power-domains = <&dispcc MDSS_GDSC>;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ };
+
+ /* S6c is really ebi.lvl but it's there for supply map completeness sake. */
+ vreg_s6c_0p88: smpc6-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vreg_s6c_0p88";
+
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-always-on;
+ vin-supply = <&vph_pwr>;
+ };
+
+ reserved-memory {
+ adsp_mem: memory@8a100000 {
+ reg = <0x0 0x8a100000 0x0 0x2500000>;
+ no-map;
+ };
+
+ spss_mem: memory@8c600000 {
+ reg = <0x0 0x8c600000 0x0 0x100000>;
+ no-map;
+ };
+
+ cdsp_secure_heap: memory@8c700000 {
+ reg = <0x0 0x8c700000 0x0 0x4600000>;
+ no-map;
+ };
+
+ cont_splash_mem: memory@9c000000 {
+ reg = <0x0 0x9c000000 0x0 0x2300000>;
+ no-map;
+ };
+
+ ramoops@ffc00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xffc00000 0x0 0x100000>;
+ record-size = <0x1000>;
+ console-size = <0x40000>;
+ msg-size = <0x20000 0x20000>;
+ ecc-size = <16>;
+ no-map;
+ };
+ };
+};
+
+&apps_rsc {
+ pm8150-rpmh-regulators {
+ compatible = "qcom,pm8150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-s9-supply = <&vph_pwr>;
+ vdd-s10-supply = <&vph_pwr>;
+ vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>;
+ vdd-l2-l10-supply = <&vreg_bob>;
+ vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p6>;
+ vdd-l6-l9-supply = <&vreg_s8c_1p2>;
+ vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
+ vdd-l13-l16-l17-supply = <&vreg_bob>;
+
+ /* (S1+S2+S3) - cx.lvl (ARC) */
+
+ vreg_s4a_1p8: smps4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5a_1p9: smps5 {
+ regulator-name = "vreg_s5a_1p9";
+ regulator-min-microvolt = <1824000>;
+ regulator-max-microvolt = <2040000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6a_0p6: smps6 {
+ regulator-name = "vreg_s6a_0p6";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1128000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2a_3p1: ldo2 {
+ regulator-name = "vreg_l2a_3p1";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3a_0p9: ldo3 {
+ regulator-name = "vreg_l3a_0p9";
+ regulator-min-microvolt = <928000>;
+ regulator-max-microvolt = <932000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L4 - lmx.lvl (ARC) */
+
+ vreg_l5a_0p88: ldo5 {
+ regulator-name = "vreg_l5a_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a_1p2: ldo6 {
+ regulator-name = "vreg_l6a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L7 is unused. */
+
+ vreg_l9a_1p2: ldo9 {
+ regulator-name = "vreg_l9a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L10 is unused, L11 - lcx.lvl (ARC) */
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L13 is unused. */
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-name = "vreg_l14a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L15 & L16 are unused. */
+
+ vreg_l17a_3p0: ldo17 {
+ regulator-name = "vreg_l17a_3p0";
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18a_0p9: ldo18 {
+ regulator-name = "vreg_l18a_0p9";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ /*
+ * Remaining regulators that are not yet supported:
+ * OLEDB: 4925000-8100000
+ * ab: 4600000-6100000
+ * ibb: 800000-5400000
+ */
+ pm8150l-rpmh-regulators {
+ compatible = "qcom,pm8150l-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+ vdd-s7-supply = <&vph_pwr>;
+ vdd-s8-supply = <&vph_pwr>;
+ vdd-l1-l8-supply = <&vreg_s4a_1p8>;
+ vdd-l2-l3-supply = <&vreg_s8c_1p2>;
+ vdd-l4-l5-l6-supply = <&vreg_bob>;
+ vdd-l7-l11-supply = <&vreg_bob>;
+ vdd-l9-l10-supply = <&vreg_bob>;
+ vdd-bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-name = "vreg_bob";
+ regulator-min-microvolt = <3350000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+
+ /*
+ * S1-S6 are ARCs:
+ * (S1+S2) - gfx.lvl,
+ * S3 - mx.lvl,
+ * (S4+S5) - mmcx.lvl,
+ * S6 - ebi.lvl
+ */
+
+ vreg_s7c_0p35: smps7 {
+ regulator-name = "vreg_s7c_0p35";
+ regulator-min-microvolt = <348000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s8c_1p2: smps8 {
+ regulator-name = "vreg_s8c_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-name = "vreg_l1c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L2-4 are unused. */
+
+ vreg_l5c_1p8: ldo5 {
+ regulator-name = "vreg_l5c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c_2p9: ldo6 {
+ regulator-name = "vreg_l6c_2p9";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l7c_2p85: ldo7 {
+ regulator-name = "vreg_l7c_2p85";
+ regulator-min-microvolt = <2856000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c_1p8: ldo8 {
+ regulator-name = "vreg_l8c_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c_2p9: ldo9 {
+ regulator-name = "vreg_l9c_2p9";
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-name = "vreg_l10c_3p3";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3296000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11c_3p0: ldo11 {
+ regulator-name = "vreg_l11c_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ pm8009-rpmh-regulators {
+ compatible = "qcom,pm8009-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vreg_bob>;
+ vdd-l2-supply = <&vreg_s8c_1p2>;
+ vdd-l5-l6-supply = <&vreg_bob>;
+ vdd-l7-supply = <&vreg_s4a_1p8>;
+
+ vreg_s1f_1p2: smps1 {
+ regulator-name = "vreg_s1f_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2f_0p5: smps2 {
+ regulator-name = "vreg_s2f_0p5";
+ regulator-min-microvolt = <512000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L1 is unused. */
+
+ vreg_l2f_1p3: ldo2 {
+ regulator-name = "vreg_l2f_1p3";
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ /* L3 & L4 are unused. */
+
+ vreg_l5f_2p8: ldo5 {
+ regulator-name = "vreg_l5f_2p85";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6f_2p8: ldo6 {
+ regulator-name = "vreg_l6f_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7f_1p8: ldo7 {
+ regulator-name = "vreg_l7f_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* NXP PN553 NFC @ 28 */
+};
+
+&i2c2 {
+ status = "okay";
+ clock-frequency = <1000000>;
+
+ /* Dual Cirrus Logic CS35L41 amps @ 40, 41 */
+};
+
+&i2c5 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* Dialog SLG51000 CMIC @ 75 */
+};
+
+&i2c9 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* AMS TCS3490 RGB+IR color sensor @ 72 */
+};
+
+&i2c13 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* Samsung touchscreen @ 48 */
+};
+
+&i2c15 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ /* Qcom SMB1390 @ 10 */
+ /* Silicon Labs SI4704 FM Radio Receiver @ 11 */
+ /* Qcom SMB1390_slave @ 18 */
+ /* HALO HL6111R Qi charger @ 25 */
+ /* Richwave RTC6226 FM Radio Receiver @ 64 */
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&qupv3_id_2 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ status = "okay";
+
+ cd-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-1 = <&sdc2_default_state &sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
+ vmmc-supply = <&vreg_l9c_2p9>;
+ vqmmc-supply = <&vreg_l6c_2p9>;
+ bus-width = <4>;
+ no-sdio;
+ no-emmc;
+};
+
+&tlmm {
+ gpio-reserved-ranges = <40 4>, <52 4>;
+
+ sdc2_default_state: sdc2-default {
+ clk {
+ pins = "sdc2_clk";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ cmd {
+ pins = "sdc2_cmd";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ data {
+ pins = "sdc2_data";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ sdc2_card_det_n: sd-card-det-n {
+ pins = "gpio77";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+};
+
+&uart12 {
+ status = "okay";
+};
+
+/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */
+&ufs_mem_hc { status = "disabled"; };
+&ufs_mem_phy { status = "disabled"; };
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l5a_0p88>;
+ vdda18-supply = <&vreg_l12a_1p8>;
+ vdda33-supply = <&vreg_l2a_3p1>;
+};
+
+&usb_1_qmpphy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l9a_1p2>;
+ vdda-pll-supply = <&vreg_l18a_0p9>;
+};
--
2.32.0
^ permalink raw reply related [flat|nested] 4+ messages in thread