From: Konrad Dybcio <konrad.dybcio@somainline.org>
To: ~postmarketos/upstreaming@lists.sr.ht
Cc: martin.botka@somainline.org,
angelogioacchino.delregno@somainline.org,
marijn.suijten@somainline.org, jamipkettunen@somainline.org,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 2/6] arm64: dts: qcom: sm8250: Commonize PCIe pins
Date: Wed, 16 Jun 2021 02:58:39 +0200 [thread overview]
Message-ID: <20210616005843.79579-2-konrad.dybcio@somainline.org> (raw)
In-Reply-To: <20210616005843.79579-1-konrad.dybcio@somainline.org>
Commonize PCIe pins, along with pin definitions for PCIe-connected
MHI modem (not enabled by default, as it's useless on modem-less boards).
While at it, remove "output-low" from the RB5 board, as it's
not necessary - we already explicitly pull the perst pin low.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 87 -------------------
arch/arm64/boot/dts/qcom/sm8250.dtsi | 101 +++++++++++++++++++++++
2 files changed, 101 insertions(+), 87 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index d5a4f5a27da6..8ac96f8e79d4 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -669,10 +669,6 @@ wifi-therm@1 {
&pcie0 {
status = "okay";
- perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>;
- wake-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie0_default_state>;
};
&pcie0_phy {
@@ -683,10 +679,6 @@ &pcie0_phy {
&pcie1 {
status = "okay";
- perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>;
- wake-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie1_default_state>;
};
&pcie1_phy {
@@ -697,10 +689,6 @@ &pcie1_phy {
&pcie2 {
status = "okay";
- perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>;
- wake-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pcie2_default_state>;
};
&pcie2_phy {
@@ -1178,81 +1166,6 @@ lt9611_irq_pin: lt9611-irq {
bias-disable;
};
- pcie0_default_state: pcie0-default {
- clkreq {
- pins = "gpio80";
- function = "pci_e0";
- bias-pull-up;
- };
-
- reset-n {
- pins = "gpio79";
- function = "gpio";
-
- drive-strength = <2>;
- output-low;
- bias-pull-down;
- };
-
- wake-n {
- pins = "gpio81";
- function = "gpio";
-
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- pcie1_default_state: pcie1-default {
- clkreq {
- pins = "gpio83";
- function = "pci_e1";
- bias-pull-up;
- };
-
- reset-n {
- pins = "gpio82";
- function = "gpio";
-
- drive-strength = <2>;
- output-low;
- bias-pull-down;
- };
-
- wake-n {
- pins = "gpio84";
- function = "gpio";
-
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- pcie2_default_state: pcie2-default {
- clkreq {
- pins = "gpio86";
- function = "pci_e2";
- bias-pull-up;
- };
-
- reset-n {
- pins = "gpio85";
- function = "gpio";
-
- drive-strength = <2>;
- output-low;
- bias-pull-down;
- };
-
- wake-n {
- pins = "gpio87";
- function = "gpio";
-
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
sdc2_default_state: sdc2-default {
clk {
pins = "sdc2_clk";
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 1665eac49f3b..e2413aee2f21 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -1314,6 +1314,12 @@ pcie0: pci@1c00000 {
phys = <&pcie0_lane>;
phy-names = "pciephy";
+ perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>;
+ enable-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_default_state>;
+
status = "disabled";
};
@@ -1412,6 +1418,12 @@ pcie1: pci@1c08000 {
phys = <&pcie1_lane>;
phy-names = "pciephy";
+ perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>;
+ enable-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default_state>;
+
status = "disabled";
};
@@ -1512,6 +1524,12 @@ pcie2: pci@1c10000 {
phys = <&pcie2_lane>;
phy-names = "pciephy";
+ perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>;
+ enable-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie2_default_state>;
+
status = "disabled";
};
@@ -3490,6 +3508,89 @@ data {
bias-pull-up;
};
};
+
+ pcie0_default_state: pcie0-default {
+ pcie0_perst_default: perst {
+ pins = "gpio79";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ clkreq {
+ pins = "gpio80";
+ function = "pci_e0";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake {
+ pins = "gpio81";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie1_default_state: pcie1-default {
+ pcie1_perst_default: perst {
+ pins = "gpio82";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ clkreq {
+ pins = "gpio83";
+ function = "pci_e1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake {
+ pins = "gpio84";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie2_default_state: pcie2-default {
+ pcie2_perst_default: perst {
+ pins = "gpio85";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ clkreq {
+ pins = "gpio86";
+ function = "pci_e2";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake {
+ pins = "gpio87";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdm2ap_default: mdm2ap-default {
+ pins = "gpio1", "gpio3";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ap2mdm_default: ap2mdm-default {
+ pins = "gpio56", "gpio57";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
};
apps_smmu: iommu@15000000 {
--
2.32.0
next prev parent reply other threads:[~2021-06-16 0:58 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-06-16 0:58 [PATCH 1/6] arm64: dts: qcom: sm8250-edo: Add hardware keys Konrad Dybcio
2021-06-16 0:58 ` Konrad Dybcio [this message]
2021-06-16 2:41 ` [PATCH 2/6] arm64: dts: qcom: sm8250: Commonize PCIe pins Bjorn Andersson
2021-06-16 0:58 ` [PATCH 3/6] arm64: dts: qcom: sm8250-edo: Enable PCIe Konrad Dybcio
2021-06-16 0:58 ` [PATCH 4/6] arm64: dts: qcom: sm8250-edo: Enable ADSP/CDSP/SLPI Konrad Dybcio
2021-06-16 2:44 ` Bjorn Andersson
2021-06-16 12:18 ` Konrad Dybcio
2021-06-16 0:58 ` [PATCH 5/6] arm64: dts: qcom: sm8250-edo: Enable GPI DMA Konrad Dybcio
2021-06-16 0:58 ` [PATCH 6/6] arm64: dts: qcom: sm8250-edo: Add Samsung touchscreen Konrad Dybcio
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210616005843.79579-2-konrad.dybcio@somainline.org \
--to=konrad.dybcio@somainline.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jamipkettunen@somainline.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=marijn.suijten@somainline.org \
--cc=martin.botka@somainline.org \
--cc=robh+dt@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.