All of lore.kernel.org
 help / color / mirror / Atom feed
From: Christoph Niedermaier <cniedermaier@dh-electronics.com>
To: <linux-arm-kernel@lists.infradead.org>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>,
	Shawn Guo <shawnguo@kernel.org>,
	Fabio Estevam <festevam@gmail.com>, Marek Vasut <marex@denx.de>,
	NXP Linux Team <linux-imx@nxp.com>, <kernel@dh-electronics.com>
Subject: [PATCH V4 12/15] ARM: dts: imx6q-dhcom: Cleanup of the devicetrees
Date: Tue, 29 Jun 2021 15:56:09 +0200	[thread overview]
Message-ID: <20210629135612.60695-12-cniedermaier@dh-electronics.com> (raw)
In-Reply-To: <20210629135612.60695-1-cniedermaier@dh-electronics.com>

Following cleanups of the devicetrees done, no change in function:
- Remove parentheses from the license
- Update copyright date
- Alphabetical sorting
- Add comments
- Update pinctrl names
- Hex values in lower case
- Set 3rd values of fixed regulators gpio property to 0
- Replace interrupt type with a define
- Remove superfluous property max-speed from the fec node

Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: kernel@dh-electronics.com
To: linux-arm-kernel@lists.infradead.org
---
V2: - Set 3rd values of fixed regulators gpio property to 0
    - Rebase on Shawn Guos branch for-next
V3: - Remove superfluous property max-speed from the fec node
    - Add Reviewed-by tag
V4: - No changes
---
 arch/arm/boot/dts/imx6q-dhcom-pdk2.dts |  90 +++++-----
 arch/arm/boot/dts/imx6q-dhcom-som.dtsi | 302 +++++++++++++++++----------------
 2 files changed, 204 insertions(+), 188 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
index bc374b629a29..91817a262cb5 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
+++ b/arch/arm/boot/dts/imx6q-dhcom-pdk2.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0+)
+// SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2015-2021 DH electronics GmbH
  * Copyright (C) 2018 Marek Vasut <marex@denx.de>
  */
 
@@ -17,27 +17,27 @@
 	};
 
 	clk_ext_audio_codec: clock-codec {
-		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24000000>;
+		compatible = "fixed-clock";
 	};
 
 	display_bl: display-bl {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
 		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		compatible = "pwm-backlight";
 		default-brightness-level = <8>;
-		enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; /* GPIO G */
+		pwms = <&pwm1 0 50000 PWM_POLARITY_INVERTED>;
 		status = "okay";
 	};
 
 	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
 		#address-cells = <1>;
 		#size-cells = <0>;
+		compatible = "fsl,imx-parallel-display";
 		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_ipu1_lcdif &pinctrl_dhcom_g>;
+		pinctrl-names = "default";
 		status = "okay";
 
 		port@0 {
@@ -62,36 +62,36 @@
 		compatible = "gpio-keys";
 
 		button-0 {
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>; /* GPIO A */
 			label = "TA1-GPIO-A";
 			linux,code = <KEY_A>;
-			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
 			pinctrl-0 = <&pinctrl_dhcom_a>;
 			pinctrl-names = "default";
 			wakeup-source;
 		};
 
 		button-1 {
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* GPIO B */
 			label = "TA2-GPIO-B";
 			linux,code = <KEY_B>;
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 			pinctrl-0 = <&pinctrl_dhcom_b>;
 			pinctrl-names = "default";
 			wakeup-source;
 		};
 
 		button-2 {
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; /* GPIO C */
 			label = "TA3-GPIO-C";
 			linux,code = <KEY_C>;
-			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
 			pinctrl-0 = <&pinctrl_dhcom_c>;
 			pinctrl-names = "default";
 			wakeup-source;
 		};
 
 		button-3 {
+			gpios = <&gpio6 3 GPIO_ACTIVE_LOW>; /* GPIO D */
 			label = "TA4-GPIO-D";
 			linux,code = <KEY_D>;
-			gpios = <&gpio6 3 GPIO_ACTIVE_LOW>;
 			pinctrl-0 = <&pinctrl_dhcom_d>;
 			pinctrl-names = "default";
 			wakeup-source;
@@ -107,9 +107,9 @@
 		 */
 		led-5 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 			gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* GPIO E */
-			default-state = "off";
 			pinctrl-0 = <&pinctrl_dhcom_e>;
 			pinctrl-names = "default";
 			status = "disabled";
@@ -117,35 +117,35 @@
 
 		led-6 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 			gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>; /* GPIO F */
-			default-state = "off";
 			pinctrl-0 = <&pinctrl_dhcom_f>;
 			pinctrl-names = "default";
 		};
 
 		led-7 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 			gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>; /* GPIO H */
-			default-state = "off";
 			pinctrl-0 = <&pinctrl_dhcom_h>;
 			pinctrl-names = "default";
 		};
 
 		led-8 {
 			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
 			function = LED_FUNCTION_INDICATOR;
 			gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* GPIO I */
-			default-state = "off";
 			pinctrl-0 = <&pinctrl_dhcom_i>;
 			pinctrl-names = "default";
 		};
 	};
 
 	panel {
-		compatible = "edt,etm0700g0edh6";
 		backlight = <&display_bl>;
+		compatible = "edt,etm0700g0edh6";
 
 		port {
 			lcd_panel_in: endpoint {
@@ -155,23 +155,23 @@
 	};
 
 	sound {
-		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&sgtl5000>;
 		audio-routing =
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias",
 			"LINE_IN", "Line In Jack",
 			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx-sgtl5000";
 		mux-ext-port = <3>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
 	};
 };
 
 &audmux {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_audmux_ext>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
@@ -188,8 +188,8 @@
 &fec {
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy7>;
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet_1G>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	mdio {
@@ -203,21 +203,21 @@
 			pinctrl-0 = <&pinctrl_ethphy7>;
 			pinctrl-names = "default";
 			reg = <7>;
-			reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
 
 			rxc-skew-ps = <3000>;
 			rxd0-skew-ps = <0>;
 			rxd1-skew-ps = <0>;
 			rxd2-skew-ps = <0>;
 			rxd3-skew-ps = <0>;
+			rxdv-skew-ps = <0>;
 			txc-skew-ps = <3000>;
 			txd0-skew-ps = <0>;
 			txd1-skew-ps = <0>;
 			txd2-skew-ps = <0>;
 			txd3-skew-ps = <0>;
-			rxdv-skew-ps = <0>;
 			txen-skew-ps = <0>;
 		};
 	};
@@ -230,21 +230,21 @@
 
 &i2c2 {
 	sgtl5000: codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
 		#sound-dai-cells = <0>;
 		clocks = <&clk_ext_audio_codec>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
 		VDDA-supply = <&reg_3p3v>;
 		VDDIO-supply = <&sw2_reg>;
 	};
 
 	touchscreen@38 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_dhcom_e>;
 		compatible = "edt,edt-ft5406";
-		reg = <0x38>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <5 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		pinctrl-0 = <&pinctrl_dhcom_e>;
+		pinctrl-names = "default";
+		reg = <0x38>;
 	};
 };
 
@@ -254,13 +254,13 @@
 
 &pcie {
 	pinctrl-0 = <&pinctrl_pcie &pinctrl_dhcom_j>;
-	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>;
+	reset-gpio = <&gpio6 14 GPIO_ACTIVE_LOW>; /* GPIO J */
 	status = "okay";
 };
 
 &pwm1 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
@@ -272,12 +272,11 @@
 	status = "okay";
 };
 
-&usdhc3 {
+&usdhc3 { /* Micro SD card on module */
 	status = "okay";
 };
 
 &iomuxc {
-	pinctrl-names = "default";
 	pinctrl-0 = <
 			/*
 			 * The following DHCOM GPIOs are used on this board.
@@ -300,50 +299,51 @@
 			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
 			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
 		>;
+	pinctrl-names = "default";
 
 	pinctrl_audmux_ext: audmux-ext-grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
 			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC		0x130b0
 			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD		0x110b0
 			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS		0x130b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD		0x130b0
 		>;
 	};
 
 	pinctrl_enet_1G: enet-1G-grp {
 		fsl,pins = <
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x100b0
-			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
-			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
-			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
-			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
-			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
-			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x100b0
 			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x100b0
-			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
 			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
 			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
 			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
 			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
 			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x100b0
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x100b0
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x100b0
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x100b0
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x100b0
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x100b0
 		>;
 	};
 
 	pinctrl_ethphy7: ethphy7-grp {
 		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0xb1 /* WOL */
 			MX6QDL_PAD_EIM_D29__GPIO3_IO29		0xb0 /* Reset */
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0xb1 /* Int */
-			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0xb1 /* WOL */
 		>;
 	};
 
 	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
 		fsl,pins = <
 			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
-			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
 			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
 			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
 			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
 			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
 			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
diff --git a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
index d20317b3fb46..1919fcf6dfa5 100644
--- a/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/imx6q-dhcom-som.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0+)
+// SPDX-License-Identifier: GPL-2.0+
 /*
- * Copyright (C) 2015 DH electronics GmbH
+ * Copyright (C) 2015-2021 DH electronics GmbH
  * Copyright (C) 2018 Marek Vasut <marex@denx.de>
  */
 
@@ -29,14 +29,22 @@
 		serial4 = &uart3;
 	};
 
-	memory@10000000 {
+	memory@10000000 { /* Appropriate memory size will be filled by U-Boot */
 		device_type = "memory";
 		reg = <0x10000000 0x20000000>;
 	};
 
+	reg_3p3v: regulator-3P3V {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "3P3V";
+	};
+
 	reg_eth_vio: regulator-eth-vio {
 		compatible = "regulator-fixed";
-		gpio = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio1 7 0>;
 		pinctrl-0 = <&pinctrl_enet_vio>;
 		pinctrl-names = "default";
 		regulator-always-on;
@@ -55,86 +63,84 @@
 		regulator-name = "latch_oe_on";
 	};
 
-	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "usb_otg_vbus";
+		enable-active-high;
+		gpio = <&gpio3 31 0>;
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
+		regulator-name = "usb_h1_vbus";
 	};
 
-	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
-		regulator-name = "usb_h1_vbus";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_3p3v: regulator-3P3V {
-		compatible = "regulator-fixed";
-		regulator-name = "3P3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
+		regulator-name = "usb_otg_vbus";
 	};
 };
 
 &can1 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	pinctrl-names = "default";
 };
 
+/*
+ * Special hardware required which uses the pins from micro SD card. The pins
+ * SD3_DAT0 and SD3_DAT1 are muxed as can2 Tx and Rx. The signals for can2 Tx
+ * and Rx are output on DHCOM uart1 rts/cts pins. So to enable can2 on the board
+ * device tree file, you also need to disable the micro SD card and the uart1
+ * rts/cts have to be disabled or output on other DHCOM pins.
+ */
 &can2 {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan2>;
+	pinctrl-names = "default";
 };
 
 &ecspi1 {
 	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>, <&gpio4 11 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi1>;
+	pinctrl-names = "default";
 	status = "okay";
 
-	flash@0 {	/* S25FL116K */
+	flash@0 { /* S25FL116K */
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-		reg = <0>;
 		m25p,fast-read;
+		reg = <0>;
+		spi-max-frequency = <50000000>;
 	};
 };
 
 &ecspi2 {
 	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
 &fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet_100M>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy0>;
+	pinctrl-0 = <&pinctrl_enet_100M>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	mdio {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethphy0: ethernet-phy@0 {	/* SMSC LAN8710Ai */
+		ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
 			compatible = "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio4>;
 			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
-			max-speed = <100>;
 			pinctrl-0 = <&pinctrl_ethphy0>;
 			pinctrl-names = "default";
 			reg = <0>;
-			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			smsc,disable-energy-detect; /* Make plugin detection reliable */
 		};
 	};
@@ -197,139 +203,147 @@
 };
 
 &i2c1 {
+	/*
+	 * Info: According to erratum ERR007805 clock frequency limit is 375000.
+	 * The erratum for i.MX6S/DL is here [1] and for i.MX6Q/D is here [2].
+	 * [1] https://www.nxp.com/docs/en/errata/IMX6SDLCE.pdf
+	 * [2] https://www.nxp.com/docs/en/errata/IMX6DQCE.pdf
+	 */
 	clock-frequency = <100000>;
-	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	pinctrl-names = "default", "gpio";
 	scl-gpios = <&gpio3 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c2 {
+	/* Info: Clock frequency limit is 375000 (for details see i2c1) */
 	clock-frequency = <100000>;
-	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	pinctrl-names = "default", "gpio";
 	scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c3 {
+	/* Info: Clock frequency limit is 375000 (for details see i2c1) */
 	clock-frequency = <100000>;
-	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
 	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	pinctrl-names = "default", "gpio";
 	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	ltc3676: pmic@3c {
 		compatible = "lltc,ltc3676";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pmic_hw300>;
-		reg = <0x3c>;
 		interrupt-parent = <&gpio5>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		reg = <0x3c>;
 
 		regulators {
 			sw1_reg: sw1 {
-				regulator-min-microvolt = <787500>;
-				regulator-max-microvolt = <1527272>;
 				lltc,fb-voltage-divider = <100000 110000>;
-				regulator-suspend-mem-microvolt = <1040000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1527272>;
+				regulator-min-microvolt = <787500>;
+				regulator-ramp-delay = <7000>;
+				regulator-suspend-mem-microvolt = <1040000>;
 			};
 
 			sw2_reg: sw2 {
-				regulator-min-microvolt = <1885714>;
-				regulator-max-microvolt = <3657142>;
 				lltc,fb-voltage-divider = <100000 28000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3657142>;
+				regulator-min-microvolt = <1885714>;
+				regulator-ramp-delay = <7000>;
 			};
 
 			sw3_reg: sw3 {
-				regulator-min-microvolt = <787500>;
-				regulator-max-microvolt = <1527272>;
 				lltc,fb-voltage-divider = <100000 110000>;
-				regulator-suspend-mem-microvolt = <980000>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1527272>;
+				regulator-min-microvolt = <787500>;
+				regulator-ramp-delay = <7000>;
+				regulator-suspend-mem-microvolt = <980000>;
 			};
 
 			sw4_reg: sw4 {
-				regulator-min-microvolt = <855571>;
-				regulator-max-microvolt = <1659291>;
 				lltc,fb-voltage-divider = <100000 93100>;
-				regulator-ramp-delay = <7000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1659291>;
+				regulator-min-microvolt = <855571>;
+				regulator-ramp-delay = <7000>;
 			};
 
 			ldo1_reg: ldo1 {
-				regulator-min-microvolt = <3240306>;
-				regulator-max-microvolt = <3240306>;
 				lltc,fb-voltage-divider = <102000 29400>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3240306>;
+				regulator-min-microvolt = <3240306>;
 			};
 
 			ldo2_reg: ldo2 {
-				regulator-min-microvolt = <2484708>;
-				regulator-max-microvolt = <2484708>;
 				lltc,fb-voltage-divider = <100000 41200>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2484708>;
+				regulator-min-microvolt = <2484708>;
 			};
 		};
 	};
 
-	touchscreen@49 {	/* TSC2004 */
+	touchscreen@49 { /* TSC2004 */
 		compatible = "ti,tsc2004";
+		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_tsc2004>;
+		pinctrl-names = "default";
 		reg = <0x49>;
 		vio-supply = <&reg_3p3v>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_tsc2004_hw300>;
-		interrupts-extended = <&gpio4 14 IRQ_TYPE_EDGE_FALLING>;
 		status = "disabled";
 	};
 
 	eeprom@50 {
 		compatible = "atmel,24c02";
-		reg = <0x50>;
 		pagesize = <16>;
+		reg = <0x50>;
 	};
 
 	rtc_i2c: rtc@56 {
 		compatible = "microcrystal,rv3029";
+		interrupt-parent = <&gpio7>;
+		interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-0 = <&pinctrl_rtc>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_rtc_hw300>;
 		reg = <0x56>;
-		interrupt-parent = <&gpio7>;
-		interrupts = <12 2>;
 	};
 };
 
 &pcie {
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie>;
+	pinctrl-names = "default";
 };
 
 &reg_arm {
 	vin-supply = <&sw3_reg>;
 };
 
-&reg_soc {
+&reg_pu {
 	vin-supply = <&sw1_reg>;
 };
 
-&reg_pu {
+&reg_soc {
 	vin-supply = <&sw1_reg>;
 };
 
@@ -341,71 +355,71 @@
 	vin-supply = <&sw2_reg>;
 };
 
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
-	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+&uart1 { /* DHCOM UART1 */
 	dcd-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
+	dtr-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
 	rng-gpios = <&gpio2 31 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pinctrl_uart1>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
 	status = "okay";
 };
 
-&uart4 {
-	pinctrl-names = "default";
+&uart4 { /* DHCOM UART3 */
 	pinctrl-0 = <&pinctrl_uart4>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
-&uart5 {
-	pinctrl-names = "default";
+&uart5 { /* DHCOM UART2 */
 	pinctrl-0 = <&pinctrl_uart5>;
+	pinctrl-names = "default";
 	uart-has-rtscts;
 	status = "okay";
 };
 
 &usbh1 {
-	pinctrl-names = "default";
+	dr_mode = "host";
 	pinctrl-0 = <&pinctrl_usbh1>;
+	pinctrl-names = "default";
 	vbus-supply = <&reg_usb_h1_vbus>;
-	dr_mode = "host";
 	status = "okay";
 };
 
 &usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
 	disable-over-current;
 	dr_mode = "otg";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	pinctrl-names = "default";
+	vbus-supply = <&reg_usb_otg_vbus>;
 	status = "okay";
 };
 
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
+&usdhc2 { /* External SD card via DHCOM */
 	cd-gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
 	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
+&usdhc3 { /* Micro SD card on module */
 	cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
 	fsl,wp-controller;
 	keep-power-in-suspend;
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-names = "default";
 	status = "disabled";
 };
 
-&usdhc4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc4>;
-	non-removable;
+&usdhc4 { /* eMMC on module */
 	bus-width = <8>;
-	no-1-8-v;
 	keep-power-in-suspend;
+	no-1-8-v;
+	non-removable;
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
@@ -413,8 +427,8 @@
 	#address-cells = <2>;
 	#size-cells = <1>;
 	fsl,weim-cs-gpr = <&gpr>;
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_weim &pinctrl_weim_cs0 &pinctrl_weim_cs1>;
+	pinctrl-names = "default";
 	/* It is necessary to setup 2x 64MB otherwise setting gpr fails */
 	ranges = <0 0 0x08000000 0x04000000>, /* CS0 */
 		 <1 0 0x0c000000 0x04000000>; /* CS1 */
@@ -422,7 +436,6 @@
 };
 
 &iomuxc {
-	pinctrl-names = "default";
 	pinctrl-0 = <
 			&pinctrl_hog_base
 			&pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
@@ -434,14 +447,17 @@
 			&pinctrl_dhcom_s &pinctrl_dhcom_t &pinctrl_dhcom_u
 			&pinctrl_dhcom_v &pinctrl_dhcom_w &pinctrl_dhcom_int
 		>;
+	pinctrl-names = "default";
 
 	pinctrl_hog_base: hog-base-grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
-			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
-			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
+			/* GPIOs for memory coding */
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x120b0
 			MX6QDL_PAD_EIM_A17__GPIO2_IO21		0x120b0
+			/* GPIOs for hardware coding */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19		0x120b0
+			MX6QDL_PAD_EIM_A22__GPIO2_IO16		0x120b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06		0x120b0
 		>;
 	};
 
@@ -544,9 +560,9 @@
 
 	pinctrl_ecspi1: ecspi1-grp {
 		fsl,pins = <
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
 			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
 			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
-			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
 			MX6QDL_PAD_EIM_EB2__GPIO2_IO30		0x1b0b0
 			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 		>;
@@ -554,18 +570,18 @@
 
 	pinctrl_ecspi2: ecspi2-grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
-			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
 			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
+			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
+			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
 			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
 		>;
 	};
 
 	pinctrl_enet_100M: enet-100M-grp {
 		fsl,pins = <
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
-			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
 			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
 			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
@@ -591,8 +607,8 @@
 
 	pinctrl_flexcan1: flexcan1-grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
 			MX6QDL_PAD_GPIO_8__FLEXCAN1_RX		0x1b0b0
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b0
 		>;
 	};
 
@@ -645,40 +661,40 @@
 		>;
 	};
 
-	pinctrl_pmic_hw300: pmic-hw300-grp {
+	pinctrl_pcie: pcie-grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1B0B0
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1 /* Wake */
 		>;
 	};
 
-	pinctrl_rtc_hw300: rtc-hw300-grp {
+	pinctrl_pmic: pmic-grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120B0
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02		0x1b0b0
 		>;
 	};
 
-	pinctrl_tsc2004_hw300: tsc2004-hw300-grp {
+	pinctrl_rtc: rtc-grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120B0
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x120b0
 		>;
 	};
 
-	pinctrl_pcie: pcie-grp {
+	pinctrl_tsc2004: tsc2004-grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1 /* Wake */
+			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x120b0
 		>;
 	};
 
 	pinctrl_uart1: uart1-grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
-			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
-			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
 			MX6QDL_PAD_EIM_D19__UART1_CTS_B		0x4001b0b1
+			MX6QDL_PAD_EIM_D20__UART1_RTS_B		0x1b0b1
 			MX6QDL_PAD_EIM_D23__GPIO3_IO23		0x4001b0b1
 			MX6QDL_PAD_EIM_D24__GPIO3_IO24		0x4001b0b1
 			MX6QDL_PAD_EIM_D25__GPIO3_IO25		0x4001b0b1
 			MX6QDL_PAD_EIM_EB3__GPIO2_IO31		0x4001b0b1
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA	0x1b0b1
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
 		>;
 	};
 
@@ -700,7 +716,7 @@
 
 	pinctrl_usbh1: usbh1-grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120B0
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120b0
 		>;
 	};
 
@@ -712,32 +728,32 @@
 
 	pinctrl_usdhc2: usdhc2-grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120b0
 			MX6QDL_PAD_SD2_CLK__SD2_CLK		0x10059
+			MX6QDL_PAD_SD2_CMD__SD2_CMD		0x17059
 			MX6QDL_PAD_SD2_DAT0__SD2_DATA0		0x17059
 			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
 			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
 			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x120B0
 		>;
 	};
 
 	pinctrl_usdhc3: usdhc3-grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
 			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
 			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
 			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120B0
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08		0x120b0
 		>;
 	};
 
 	pinctrl_usdhc4: usdhc4-grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
 			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
+			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
 			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
 			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
 			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
@@ -751,26 +767,26 @@
 
 	pinctrl_weim: weim-grp {
 		fsl,pins = <
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0a6
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0a6
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0a6
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0a6
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0a6
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0a6
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0a6
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0a6
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0a6
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0a6
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0a6
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0a6
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0a6
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0a6
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0a6
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0a6
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
+			MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb060 /* LE */
 			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0a6
 			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0a6 /* WE */
-			MX6QDL_PAD_EIM_LBA__EIM_LBA_B		0xb060 /* LE */
-			MX6QDL_PAD_EIM_D22__GPIO3_IO22		0x130b0
-			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0a6
-			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0a6
-			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0a6
-			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0a6
-			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0a6
-			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0a6
-			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0a6
-			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0a6
-			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0a6
-			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0a6
-			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0a6
-			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0a6
-			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0a6
-			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0a6
-			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0a6
-			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0a6
 		>;
 	};
 
-- 
2.11.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2021-06-29 14:59 UTC|newest]

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-06-29 13:55 [PATCH V4 01/15] ARM: dts: imx6q-dhcom: Add the parallel system bus Christoph Niedermaier
2021-06-29 13:55 ` [PATCH V4 02/15] ARM: dts: imx6q-dhcom: Add interrupt and compatible to the ethernet PHY Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 03/15] ARM: dts: imx6q-dhcom: Fill GPIO line names on DHCOM SoM Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 04/15] ARM: dts: imx6q-dhcom: Adding Wake pin to the PCIe pinctrl Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 05/15] ARM: dts: imx6q-dhcom: Align stdout-path with other DHCOM SoMs Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 06/15] ARM: dts: imx6q-dhcom: Add keys and leds to the PDK2 board Christoph Niedermaier
2021-06-29 15:10   ` Marek Vasut
2021-06-30 12:16     ` Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 07/15] ARM: dts: imx6q-dhcom: Use 1G ethernet on " Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 08/15] ARM: dts: imx6q-dhcom: Rework of the DHCOM GPIO pinctrls Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 09/15] ARM: dts: imx6q-dhcom: Remove ddc-i2c-bus property Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 10/15] ARM: dts: imx6q-dhcom: Set minimum memory size of all DHCOM i.MX6 variants Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 11/15] ARM: dts: imx6q-dhcom: Rearrange of iomux Christoph Niedermaier
2021-06-29 13:56 ` Christoph Niedermaier [this message]
2021-06-29 13:56 ` [PATCH V4 13/15] ARM: dts: imx6qdl-dhcom: Split SoC-independent parts of DHCOM SOM and PDK2 Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 14/15] ARM: dts: imx6qdl-dhcom: Add DHCOM based PicoITX board Christoph Niedermaier
2021-06-29 13:56 ` [PATCH V4 15/15] ARM: dts: imx6qdl-dhcom: Add DHSOM based DRC02 board Christoph Niedermaier

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210629135612.60695-12-cniedermaier@dh-electronics.com \
    --to=cniedermaier@dh-electronics.com \
    --cc=festevam@gmail.com \
    --cc=kernel@dh-electronics.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-imx@nxp.com \
    --cc=marex@denx.de \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.