[PATCH v2 01/18] dt-bindings: arm: cpus: Add Kryo 560 CPUs

[PATCH v2 01/18] dt-bindings: arm: cpus: Add Kryo 560 CPUs

[Konrad Dybcio]

Document Kryo 560 CPUs found in Qualcomm Snapdragon 690 (SM6350).

Reviewed-by:  AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/cpus.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml
index 9a2432a88074..897eec887e5a 100644
--- a/Documentation/devicetree/bindings/arm/cpus.yaml
+++ b/Documentation/devicetree/bindings/arm/cpus.yaml
@@ -171,6 +171,7 @@ properties:
       - qcom,kryo385
       - qcom,kryo468
       - qcom,kryo485
+      - qcom,kryo560
       - qcom,kryo685
       - qcom,scorpion
 
-- 
2.33.0

[PATCH v2 02/18] arm64: dts: qcom: Add SM6350 device tree

[Konrad Dybcio]

Add a base DT for SM6350 SoC

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 487 +++++++++++++++++++++++++++
 1 file changed, 487 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6350.dtsi

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
new file mode 100644
index 000000000000..9a9797f5a55b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -0,0 +1,487 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_0>;
+			#cooling-cells = <2>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+					compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_100>;
+			#cooling-cells = <2>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_200>;
+			#cooling-cells = <2>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_300>;
+			#cooling-cells = <2>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_400>;
+			#cooling-cells = <2>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			dynamic-power-coefficient = <100>;
+			next-level-cache = <&L2_500>;
+			#cooling-cells = <2>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1894>;
+			dynamic-power-coefficient = <703>;
+			next-level-cache = <&L2_600>;
+			#cooling-cells = <2>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo560";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1894>;
+			dynamic-power-coefficient = <703>;
+			next-level-cache = <&L2_700>;
+			#cooling-cells = <2>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&CPU6>;
+				};
+
+				core1 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm6350", "qcom,scm";
+			#reset-cells = <1>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			reg = <0 0x80000000 0 0x600000>;
+			no-map;
+		};
+
+		xbl_aop_mem: memory@80700000 {
+			reg = <0 0x80700000 0 0x160000>;
+			no-map;
+		};
+
+		cmd_db: memory@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0 0x80860000 0 0x20000>;
+			no-map;
+		};
+
+		sec_apps_mem: memory@808ff000 {
+			reg = <0 0x808ff000 0 0x1000>;
+			no-map;
+		};
+
+		smem_mem: memory@80900000 {
+			reg = <0 0x80900000 0 0x200000>;
+			no-map;
+		};
+
+		cdsp_sec_mem: memory@80b00000 {
+			reg = <0 0x80b00000 0 0x1e00000>;
+			no-map;
+		};
+
+		pil_camera_mem: memory@86000000 {
+			reg = <0 0x86000000 0 0x500000>;
+			no-map;
+		};
+
+		pil_npu_mem: memory@86500000 {
+			reg = <0 0x86500000 0 0x500000>;
+			no-map;
+		};
+
+		pil_video_mem: memory@86a00000 {
+			reg = <0 0x86a00000 0 0x500000>;
+			no-map;
+		};
+
+		pil_cdsp_mem: memory@86f00000 {
+			reg = <0 0x86f00000 0 0x1e00000>;
+			no-map;
+		};
+
+		pil_adsp_mem: memory@88d00000 {
+			reg = <0 0x88d00000 0 0x2800000>;
+			no-map;
+		};
+
+		wlan_fw_mem: memory@8b500000 {
+			reg = <0 0x8b500000 0 0x200000>;
+			no-map;
+		};
+
+		pil_ipa_fw_mem: memory@8b700000 {
+			reg = <0 0x8b700000 0 0x10000>;
+			no-map;
+		};
+
+		pil_ipa_gsi_mem: memory@8b710000 {
+			reg = <0 0x8b710000 0 0x5400>;
+			no-map;
+		};
+
+		pil_gpu_mem: memory@8b715400 {
+			reg = <0 0x8b715400 0 0x2000>;
+			no-map;
+		};
+
+		pil_modem_mem: memory@8b800000 {
+			reg = <0 0x8b800000 0 0xf800000>;
+			no-map;
+		};
+
+		cont_splash_memory: memory@a0000000 {
+			reg = <0 0xa0000000 0 0x2300000>;
+			no-map;
+		};
+
+		dfps_data_memory: memory@a2300000 {
+			reg = <0 0xa2300000 0 0x100000>;
+			no-map;
+		};
+
+		removed_region: memory@c0000000 {
+			reg = <0 0xc0000000 0 0x3900000>;
+			no-map;
+		};
+
+		debug_region: memory@ffb00000 {
+			reg = <0 0xffb00000 0 0xc0000>;
+			no-map;
+		};
+
+		last_log_region: memory@ffbc0000 {
+			reg = <0 0xffbc0000 0 0x40000>;
+			no-map;
+		};
+
+		ramoops: ramoops@ffc00000 {
+			compatible = "removed-dma-pool", "ramoops";
+			reg = <0 0xffc00000 0 0x00100000>;
+			record-size = <0x1000>;
+			console-size = <0x40000>;
+			ftrace-size = <0x0>;
+			msg-size = <0x20000 0x20000>;
+			cc-size = <0x0>;
+			no-map;
+		};
+
+		cmdline_region: memory@ffd00000 {
+			reg = <0 0xffd00000 0 0x1000>;
+			no-map;
+		};
+	};
+
+	smem {
+		compatible = "qcom,smem";
+		memory-region = <&smem_mem>;
+		hwlocks = <&tcsr_mutex 3>;
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		ipcc: mailbox@408000 {
+			compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
+			reg = <0 0x00408000 0 0x1000>;
+			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#mbox-cells = <2>;
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm6350-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
+			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
+					  <125 63 1>, <126 655 12>, <138 139 15>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog@17c10000 {
+			compatible = "qcom,apss-wdt-sm6350", "qcom,kpss-wdt";
+			reg = <0 0x17c10000 0 0x1000>;
+			clocks = <&sleep_clk>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer@17c20000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			frame@17c21000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c21000 0x0 0x1000>,
+				      <0x0 0x17c22000 0x0 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c23000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c25000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c27000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c29000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@18200000 {
+			compatible = "qcom,rpmh-rsc";
+			label = "apps_rsc";
+			reg = <0x0 0x18200000 0x0 0x10000>,
+				<0x0 0x18210000 0x0 0x10000>,
+				<0x0 0x18220000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
+					  <WAKE_TCS 3>, <CONTROL_TCS 1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		clock-frequency = <19200000>;
+		interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
-- 
2.33.0

[PATCH v2 03/18] arm64: dts: qcom: sm6350: Add LLCC node

[Konrad Dybcio]

Add a node for LLCC with SM6350-specific compatible.

Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 9a9797f5a55b..2a7a5409cd1a 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -374,6 +374,12 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		system-cache-controller@9200000 {
+			compatible = "qcom,sm6350-llcc";
+			reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
+			reg-names = "llcc_base", "llcc_broadcast_base";
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm6350-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
-- 
2.33.0

[PATCH v2 04/18] arm64: dts: qcom: sm6350: Add RPMHCC node

[Konrad Dybcio]

Add RPMHCC node to allow for referencing RPMH-controlled clocks in other
nodes.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 2a7a5409cd1a..95fdf40e3d60 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -479,6 +479,13 @@ apps_rsc: rsc@18200000 {
 			qcom,drv-id = <2>;
 			qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
 					  <WAKE_TCS 3>, <CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sm6350-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
 		};
 	};
 
-- 
2.33.0

[PATCH v2 05/18] arm64: dts: qcom: sm6350: Add GCC node

[Konrad Dybcio]

Add and configure GCC node to allow for referencing GCC-controlled clocks
in other nodes.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 95fdf40e3d60..d57c669ae0d6 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -3,6 +3,8 @@
  * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
  */
 
+#include <dt-bindings/clock/qcom,gcc-sm6350.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
@@ -359,6 +361,20 @@ soc: soc@0 {
 		dma-ranges = <0 0 0 0 0x10 0>;
 		compatible = "simple-bus";
 
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm6350";
+			reg = <0 0x00100000 0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo",
+				      "bi_tcxo_ao",
+				      "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>;
+		};
+
 		ipcc: mailbox@408000 {
 			compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
 			reg = <0 0x00408000 0 0x1000>;
-- 
2.33.0

[PATCH v2 06/18] arm64: dts: qcom: sm6350: Add TLMM block node

[Konrad Dybcio]

Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
Changes since v1:
- Fix the gpio ranges from 156 to 157

 arch/arm64/boot/dts/qcom/sm6350.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index d57c669ae0d6..03f7601457b4 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -406,6 +406,25 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm6350-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 157>;
+		};
+
 		intc: interrupt-controller@17a00000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
-- 
2.33.0

[PATCH v2 07/18] arm64: dts: qcom: sm6350: Add USB1 nodes

[Konrad Dybcio]

Add nodes required for USB1 to function. SM6350 (thankfully) resuses SDM845 and
SC7180 IP, so no additional code porting is required.

Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 101 +++++++++++++++++++++++++++
 1 file changed, 101 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 03f7601457b4..ee28c7cbab81 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -390,12 +390,113 @@ tcsr_mutex: hwlock@1f40000 {
 			#hwlock-cells = <1>;
 		};
 
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sm6350-qusb2-phy", "qcom,qusb2-v2-phy";
+			reg = <0 0x088e3000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&xo_board>, <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_1_qmpphy: phy@88e9000 {
+			compatible = "qcom,sc7180-qmp-usb3-dp-phy";
+			reg = <0 0x088e9000 0 0x200>,
+			      <0 0x088e8000 0 0x40>,
+			      <0 0x088ea000 0 0x200>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_QLINK_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
+				 <&xo_board>;
+			clock-names = "aux", "ref", "com_aux", "cfg_ahb";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: usb3-phy@88e9200 {
+				reg = <0 0x088e9200 0 0x200>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x400>,
+				      <0 0x088e9600 0 0x200>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
+				#clock-cells = <0>;
+				#phy-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+
+			dp_phy: dp-phy@88ea200 {
+				reg = <0 0x088ea200 0 0x200>,
+				      <0 0x088ea400 0 0x200>,
+				      <0 0x088eac00 0 0x400>,
+				      <0 0x088ea600 0 0x200>,
+				      <0 0x088ea800 0 0x200>,
+				      <0 0x088eaa00 0 0x100>;
+				#phy-cells = <0>;
+				#clock-cells = <1>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
 		system-cache-controller@9200000 {
 			compatible = "qcom,sm6350-llcc";
 			reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
 		};
 
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm6350-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+				      "sleep";
+
+			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
+					  "dm_hs_phy_irq", "ss_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: dwc3@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				snps,has-lpm-erratum;
+				snps,hird-threshold = /bits/ 8 <0x10>;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sm6350-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
-- 
2.33.0

[PATCH v2 08/18] arm64: dts: qcom: sm6350: Add cpufreq-hw support

[Konrad Dybcio]

Add cpufreq-hw node and assign qcom,freq-domain properties to CPUs to enable
CPU clock scaling.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index ee28c7cbab81..d945a44e63df 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -42,6 +42,7 @@ CPU0: cpu@0 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_0>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_0: l2-cache {
 				compatible = "cache";
@@ -60,6 +61,7 @@ CPU1: cpu@100 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_100>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_100: l2-cache {
 				compatible = "cache";
@@ -75,6 +77,7 @@ CPU2: cpu@200 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_200>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_200: l2-cache {
 				compatible = "cache";
@@ -90,6 +93,7 @@ CPU3: cpu@300 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_300>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_300: l2-cache {
 				compatible = "cache";
@@ -105,6 +109,7 @@ CPU4: cpu@400 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_400>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_400: l2-cache {
 				compatible = "cache";
@@ -120,6 +125,7 @@ CPU5: cpu@500 {
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <100>;
 			next-level-cache = <&L2_500>;
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_500: l2-cache {
 				compatible = "cache";
@@ -136,6 +142,7 @@ CPU6: cpu@600 {
 			capacity-dmips-mhz = <1894>;
 			dynamic-power-coefficient = <703>;
 			next-level-cache = <&L2_600>;
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			L2_600: l2-cache {
 				compatible = "cache";
@@ -151,6 +158,7 @@ CPU7: cpu@700 {
 			capacity-dmips-mhz = <1894>;
 			dynamic-power-coefficient = <703>;
 			next-level-cache = <&L2_700>;
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			L2_700: l2-cache {
 				compatible = "cache";
@@ -623,6 +631,16 @@ rpmhcc: clock-controller {
 				clocks = <&xo_board>;
 			};
 		};
+
+		cpufreq_hw: cpufreq@18323000 {
+			compatible = "qcom,cpufreq-hw";
+			reg = <0 0x18323000 0 0x1000>, <0 0x18325800 0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
+			clock-names = "xo", "alternate";
+
+			#freq-domain-cells = <1>;
+		};
 	};
 
 	timer {
-- 
2.33.0

[PATCH v2 09/18] arm64: dts: qcom: sm6350: Add TSENS nodes

[Konrad Dybcio]

Add nodes required for TSENS block using the common qcom,tsens-v2 binding.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index d945a44e63df..986d7fb01cbb 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -515,6 +515,28 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		tsens0: thermal-sensor@c263000 {
+			compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c263000 0 0x1ff>, /* TM */
+			      <0 0x0c222000 0 0x8>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens1: thermal-sensor@c265000 {
+			compatible = "qcom,sm6350-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c265000 0 0x1ff>, /* TM */
+			      <0 0x0c223000 0 0x8>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+				     <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,sm6350-tlmm";
 			reg = <0 0x0f100000 0 0x300000>;
-- 
2.33.0

[PATCH v2 10/18] arm64: dts: qcom: sm6350: Add AOSS_QMP

[Konrad Dybcio]

Add a node for AOSS_QMP in preparation for remote processor enablement.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 986d7fb01cbb..d903173b7dbc 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -537,6 +537,17 @@ tsens1: thermal-sensor@c265000 {
 			#thermal-sensor-cells = <1>;
 		};
 
+		aoss_qmp: power-controller@c300000 {
+			compatible = "qcom,sm6350-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x1000>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+			#power-domain-cells = <1>;
+		};
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,sm6350-tlmm";
 			reg = <0 0x0f100000 0 0x300000>;
-- 
2.33.0

[PATCH v2 11/18] arm64: dts: qcom: sm6350: Add SPMI bus

[Konrad Dybcio]

Add a node for SPMI to allow for communication with on-board PMICs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index d903173b7dbc..f3914309dc5f 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -548,6 +548,24 @@ aoss_qmp: power-controller@c300000 {
 			#power-domain-cells = <1>;
 		};
 
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0 0xc440000 0 0x1100>,
+			      <0 0xc600000 0 0x2000000>,
+			      <0 0xe600000 0 0x100000>,
+			      <0 0xe700000 0 0xa0000>,
+			      <0 0xc40a000 0 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,sm6350-tlmm";
 			reg = <0 0x0f100000 0 0x300000>;
-- 
2.33.0

[PATCH v2 12/18] arm64: dts: qcom: sm6350: Add PRNG node

[Konrad Dybcio]

Add a node for the PRNG to enable hw-accelerated pseudo-random number
generation.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index f3914309dc5f..30ecacce176e 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -392,6 +392,13 @@ ipcc: mailbox@408000 {
 			#mbox-cells = <2>;
 		};
 
+		rng: rng@793000 {
+			compatible = "qcom,prng-ee";
+			reg = <0 0x00793000 0 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x40000>;
-- 
2.33.0

[PATCH v2 13/18] arm64: dts: qcom: sm6350: Add RPMHPD and BCM voter

[Konrad Dybcio]

Add RPMHPD node, its OPP table and BCM voter to prepare for performance level
voting.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 54 ++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 30ecacce176e..2bc6c06c68bb 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -688,6 +688,60 @@ rpmhcc: clock-controller {
 				clock-names = "xo";
 				clocks = <&xo_board>;
 			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sm6350-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm_voter {
+				compatible = "qcom,bcm-voter";
+			};
 		};
 
 		cpufreq_hw: cpufreq@18323000 {
-- 
2.33.0

[PATCH v2 14/18] arm64: dts: qcom: sm6350: Add SDHCI1/2 nodes

[Konrad Dybcio]

Add SDHCI1/2 nodes for eMMC and uSD card respectively.
Do note that most SM6350 devices seem to come with UFS.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 81 ++++++++++++++++++++++++++++
 1 file changed, 81 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 2bc6c06c68bb..c4c1e94e69e1 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -399,12 +400,92 @@ rng: rng@793000 {
 			clock-names = "core";
 		};
 
+		sdhc_1: sdhci@7c4000 {
+			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x007c4000 0 0x1000>,
+				<0 0x007c5000 0 0x1000>,
+				<0 0x007c8000 0 0x8000>;
+			reg-names = "hc", "cqhci", "ice";
+
+			interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			qcom,dll-config = <0x000f642c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd SM6350_CX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+			bus-width = <8>;
+			non-removable;
+			supports-cqe;
+
+			status = "disabled";
+
+			sdhc1_opp_table: sdhc1-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x40000>;
 			#hwlock-cells = <1>;
 		};
 
+		sdhc_2: sdhci@8804000 {
+			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd SM6350_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+			bus-width = <4>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: sdhc2-opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+			};
+		};
+
 		usb_1_hsphy: phy@88e3000 {
 			compatible = "qcom,sm6350-qusb2-phy", "qcom,qusb2-v2-phy";
 			reg = <0 0x088e3000 0 0x400>;
-- 
2.33.0

[PATCH v2 15/18] arm64: dts: qcom: sm6350: Add apps_smmu

[Konrad Dybcio]

Add a node for the APPS SMMU to allow for managing memory access to peripherals
such as the USB controller.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 88 ++++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index c4c1e94e69e1..a3a1f0e63ace 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -673,6 +673,94 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 157>;
 		};
 
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm6350-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		intc: interrupt-controller@17a00000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
-- 
2.33.0

[PATCH v2 16/18] arm64: dts: qcom: sm6350: Add iommus property to USB1

[Konrad Dybcio]

This is required for us to be able to access the associated registers, which
are (on at least some devices) gated by default.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/sm6350.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index a3a1f0e63ace..95e69d9f8657 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -584,6 +584,7 @@ usb_1_dwc3: dwc3@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x540 0x0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_enblslpm_quirk;
 				snps,has-lpm-erratum;
-- 
2.33.0

[PATCH v2 17/18] arm64: dts: qcom: Add device tree for Sony Xperia 10 III

[Konrad Dybcio]

Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
trees. There is no sign of another Lena devices on the horizon, so a common
DTSI is not created for now. 10 III features a Full HD OLED display and 5G
support, among other nice things like USB3.

The bootloader is VERY unpleasant, to get a bootable setup you have to run:

mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
--dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
--cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
--ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
--os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
--header_version 2 -o mainline.img

adb reboot bootloader

// You have to either pull vbmeta{"","_system"} from
// /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
fastboot --disable-verity --disable-verification flash vbmeta_system \
vbmeta_system.img

fastboot flash boot mainline.img
fastboot erase dtbo // This will take approx 70s...
fastboot reboot

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |  1 +
 .../qcom/sm6350-sony-xperia-lena-pdx213.dts   | 57 +++++++++++++++++++
 2 files changed, 58 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 5bbeb058e1f2..d1ace2541ce1 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -78,6 +78,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-akatsuki.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-apollo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
new file mode 100644
index 000000000000..a26c23754f5d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+/dts-v1/;
+
+#include "sm6350.dtsi"
+
+/ {
+	model = "Sony Xperia 10 III";
+	compatible = "sony,pdx213", "qcom,sm6350";
+	qcom,msm-id = <434 0x10000>, <459 0x10000>;
+	qcom,board-id = <0x1000B 0>;
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer: framebuffer@a0000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0xa0000000 0 0x2300000>;
+			width = <1080>;
+			height = <2520>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+			clocks = <&gcc GCC_DISP_AXI_CLK>;
+		};
+	};
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <13 4>, <45 2>, <56 2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	maximum-speed = "super-speed";
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+};
-- 
2.33.0

[PATCH v2 18/18] arm64: dts: qcom: pm6150l: Add missing include

[Konrad Dybcio]

Add missing include to make it compile.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
---
 arch/arm64/boot/dts/qcom/pm6150l.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
index b49860cd1387..3ca2860bb0cf 100644
--- a/arch/arm64/boot/dts/qcom/pm6150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: BSD-3-Clause
 // Copyright (c) 2019, The Linux Foundation. All rights reserved.
 
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
-- 
2.33.0

Re: [PATCH v2 06/18] arm64: dts: qcom: sm6350: Add TLMM block node

[Maulik Shah]

Hi,

On 8/28/2021 6:48 PM, Konrad Dybcio wrote:
> Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
> Changes since v1:
> - Fix the gpio ranges from 156 to 157
>
>   arch/arm64/boot/dts/qcom/sm6350.dtsi | 19 +++++++++++++++++++
>   1 file changed, 19 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index d57c669ae0d6..03f7601457b4 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -406,6 +406,25 @@ pdc: interrupt-controller@b220000 {
>   			interrupt-controller;
>   		};
>   
> +		tlmm: pinctrl@f100000 {
> +			compatible = "qcom,sm6350-tlmm";
> +			reg = <0 0x0f100000 0 0x300000>;
> +			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
> +					<GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
you will not require other interrupts (209 to 216) for dual edge to work 
since you have below set in pinctrl-sm6350.c

.wakeirq_dual_edge_errata = true,

Thanks,
Maulik
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +			gpio-ranges = <&tlmm 0 0 157>;
> +		};
> +
>   		intc: interrupt-controller@17a00000 {
>   			compatible = "arm,gic-v3";
>   			#interrupt-cells = <3>;

-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v2 06/18] arm64: dts: qcom: sm6350: Add TLMM block node

[Konrad Dybcio]

On 28.08.2021 17:47, Maulik Shah wrote:
> Hi,
>
> On 8/28/2021 6:48 PM, Konrad Dybcio wrote:
>> Add TLMM pinctrl node to enable referencing the SoC pins in other nodes.
>>
>> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
>> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
>> ---
>> Changes since v1:
>> - Fix the gpio ranges from 156 to 157
>>
>>   arch/arm64/boot/dts/qcom/sm6350.dtsi | 19 +++++++++++++++++++
>>   1 file changed, 19 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
>> index d57c669ae0d6..03f7601457b4 100644
>> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
>> @@ -406,6 +406,25 @@ pdc: interrupt-controller@b220000 {
>>               interrupt-controller;
>>           };
>>   +        tlmm: pinctrl@f100000 {
>> +            compatible = "qcom,sm6350-tlmm";
>> +            reg = <0 0x0f100000 0 0x300000>;
>> +            interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
>> +                    <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
> you will not require other interrupts (209 to 216) for dual edge to work since you have below set in pinctrl-sm6350.c
>
> .wakeirq_dual_edge_errata = true,
>
> Thanks,
> Maulik


Right, I updated the binding but not the dt... Thanks for spotting that.


Konrad

Re: [PATCH v2 02/18] arm64: dts: qcom: Add SM6350 device tree

[Maulik Shah]

Hi,

On 8/28/2021 6:47 PM, Konrad Dybcio wrote:
> Add a base DT for SM6350 SoC
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
>   arch/arm64/boot/dts/qcom/sm6350.dtsi | 487 +++++++++++++++++++++++++++
>   1 file changed, 487 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/sm6350.dtsi
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> new file mode 100644
> index 000000000000..9a9797f5a55b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -0,0 +1,487 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/mailbox/qcom-ipcc.h>
> +#include <dt-bindings/soc/qcom,rpmh-rsc.h>
> +
> +/ {
> +	interrupt-parent = <&intc>;
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +
> +	clocks {
> +		xo_board: xo-board {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <76800000>;
> +			clock-output-names = "xo_board";
> +		};
> +
> +		sleep_clk: sleep-clk {
> +			compatible = "fixed-clock";
> +			clock-frequency = <32764>;
> +			#clock-cells = <0>;
> +		};
> +	};
> +
> +	cpus {
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		CPU0: cpu@0 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x0>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_0>;
> +			#cooling-cells = <2>;
> +			L2_0: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +				L3_0: l3-cache {
> +					compatible = "cache";
> +				};
> +			};
> +		};
> +
> +		CPU1: cpu@100 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x100>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_100>;
> +			#cooling-cells = <2>;
> +			L2_100: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		CPU2: cpu@200 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x200>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_200>;
> +			#cooling-cells = <2>;
> +			L2_200: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		CPU3: cpu@300 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x300>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_300>;
> +			#cooling-cells = <2>;
> +			L2_300: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		CPU4: cpu@400 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x400>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_400>;
> +			#cooling-cells = <2>;
> +			L2_400: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		CPU5: cpu@500 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x500>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1024>;
> +			dynamic-power-coefficient = <100>;
> +			next-level-cache = <&L2_500>;
> +			#cooling-cells = <2>;
> +			L2_500: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +
> +		};
> +
> +		CPU6: cpu@600 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x600>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1894>;
> +			dynamic-power-coefficient = <703>;
> +			next-level-cache = <&L2_600>;
> +			#cooling-cells = <2>;
> +			L2_600: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		CPU7: cpu@700 {
> +			device_type = "cpu";
> +			compatible = "qcom,kryo560";
> +			reg = <0x0 0x700>;
> +			enable-method = "psci";
> +			capacity-dmips-mhz = <1894>;
> +			dynamic-power-coefficient = <703>;
> +			next-level-cache = <&L2_700>;
> +			#cooling-cells = <2>;
> +			L2_700: l2-cache {
> +				compatible = "cache";
> +				next-level-cache = <&L3_0>;
> +			};
> +		};
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&CPU0>;
> +				};
> +
> +				core1 {
> +					cpu = <&CPU1>;
> +				};
> +
> +				core2 {
> +					cpu = <&CPU2>;
> +				};
> +
> +				core3 {
> +					cpu = <&CPU3>;
> +				};
> +
> +				core4 {
> +					cpu = <&CPU4>;
> +				};
> +
> +				core5 {
> +					cpu = <&CPU5>;
> +				};
> +			};
> +
> +			cluster1 {
> +				core0 {
> +					cpu = <&CPU6>;
> +				};
> +
> +				core1 {
> +					cpu = <&CPU7>;
> +				};
> +			};
> +		};
> +	};
> +
> +	firmware {
> +		scm: scm {
> +			compatible = "qcom,scm-sm6350", "qcom,scm";
> +			#reset-cells = <1>;
> +		};
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		/* We expect the bootloader to fill in the size */
> +		reg = <0x0 0x80000000 0x0 0x0>;
> +	};
> +
> +	pmu {
> +		compatible = "arm,armv8-pmuv3";
> +		interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_LOW>;
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-1.0";
> +		method = "smc";
> +	};
> +
> +	reserved_memory: reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		hyp_mem: memory@80000000 {
> +			reg = <0 0x80000000 0 0x600000>;
> +			no-map;
> +		};
> +
> +		xbl_aop_mem: memory@80700000 {
> +			reg = <0 0x80700000 0 0x160000>;
> +			no-map;
> +		};
> +
> +		cmd_db: memory@80860000 {
> +			compatible = "qcom,cmd-db";
> +			reg = <0 0x80860000 0 0x20000>;
> +			no-map;
> +		};
> +
> +		sec_apps_mem: memory@808ff000 {
> +			reg = <0 0x808ff000 0 0x1000>;
> +			no-map;
> +		};
> +
> +		smem_mem: memory@80900000 {
> +			reg = <0 0x80900000 0 0x200000>;
> +			no-map;
> +		};
> +
> +		cdsp_sec_mem: memory@80b00000 {
> +			reg = <0 0x80b00000 0 0x1e00000>;
> +			no-map;
> +		};
> +
> +		pil_camera_mem: memory@86000000 {
> +			reg = <0 0x86000000 0 0x500000>;
> +			no-map;
> +		};
> +
> +		pil_npu_mem: memory@86500000 {
> +			reg = <0 0x86500000 0 0x500000>;
> +			no-map;
> +		};
> +
> +		pil_video_mem: memory@86a00000 {
> +			reg = <0 0x86a00000 0 0x500000>;
> +			no-map;
> +		};
> +
> +		pil_cdsp_mem: memory@86f00000 {
> +			reg = <0 0x86f00000 0 0x1e00000>;
> +			no-map;
> +		};
> +
> +		pil_adsp_mem: memory@88d00000 {
> +			reg = <0 0x88d00000 0 0x2800000>;
> +			no-map;
> +		};
> +
> +		wlan_fw_mem: memory@8b500000 {
> +			reg = <0 0x8b500000 0 0x200000>;
> +			no-map;
> +		};
> +
> +		pil_ipa_fw_mem: memory@8b700000 {
> +			reg = <0 0x8b700000 0 0x10000>;
> +			no-map;
> +		};
> +
> +		pil_ipa_gsi_mem: memory@8b710000 {
> +			reg = <0 0x8b710000 0 0x5400>;
> +			no-map;
> +		};
> +
> +		pil_gpu_mem: memory@8b715400 {
> +			reg = <0 0x8b715400 0 0x2000>;
> +			no-map;
> +		};
> +
> +		pil_modem_mem: memory@8b800000 {
> +			reg = <0 0x8b800000 0 0xf800000>;
> +			no-map;
> +		};
> +
> +		cont_splash_memory: memory@a0000000 {
> +			reg = <0 0xa0000000 0 0x2300000>;
> +			no-map;
> +		};
> +
> +		dfps_data_memory: memory@a2300000 {
> +			reg = <0 0xa2300000 0 0x100000>;
> +			no-map;
> +		};
> +
> +		removed_region: memory@c0000000 {
> +			reg = <0 0xc0000000 0 0x3900000>;
> +			no-map;
> +		};
> +
> +		debug_region: memory@ffb00000 {
> +			reg = <0 0xffb00000 0 0xc0000>;
> +			no-map;
> +		};
> +
> +		last_log_region: memory@ffbc0000 {
> +			reg = <0 0xffbc0000 0 0x40000>;
> +			no-map;
> +		};
> +
> +		ramoops: ramoops@ffc00000 {
> +			compatible = "removed-dma-pool", "ramoops";
> +			reg = <0 0xffc00000 0 0x00100000>;
> +			record-size = <0x1000>;
> +			console-size = <0x40000>;
> +			ftrace-size = <0x0>;
> +			msg-size = <0x20000 0x20000>;
> +			cc-size = <0x0>;
> +			no-map;
> +		};
> +
> +		cmdline_region: memory@ffd00000 {
> +			reg = <0 0xffd00000 0 0x1000>;
> +			no-map;
> +		};
> +	};
> +
> +	smem {
> +		compatible = "qcom,smem";
> +		memory-region = <&smem_mem>;
> +		hwlocks = <&tcsr_mutex 3>;
> +	};
> +
> +	soc: soc@0 {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges = <0 0 0 0 0x10 0>;
> +		dma-ranges = <0 0 0 0 0x10 0>;
> +		compatible = "simple-bus";
> +
> +		ipcc: mailbox@408000 {
> +			compatible = "qcom,sm6350-ipcc", "qcom,ipcc";
> +			reg = <0 0x00408000 0 0x1000>;
> +			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			#mbox-cells = <2>;
> +		};
> +
> +		tcsr_mutex: hwlock@1f40000 {
> +			compatible = "qcom,tcsr-mutex";
> +			reg = <0x0 0x01f40000 0x0 0x40000>;
> +			#hwlock-cells = <1>;
> +		};
> +
> +		pdc: interrupt-controller@b220000 {
> +			compatible = "qcom,sm6350-pdc", "qcom,pdc";
> +			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;

The second reg  0x17c000f0 is neither documented nor used in PDC irq 
chip driver. can you please remove it?

Thanks,
Maulik
> +			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
> +					  <125 63 1>, <126 655 12>, <138 139 15>;
> +			#interrupt-cells = <2>;
> +			interrupt-parent = <&intc>;
> +			interrupt-controller;
> +		};
> +
> +		intc: interrupt-controller@17a00000 {
> +			compatible = "arm,gic-v3";
> +			#interrupt-cells = <3>;
> +			interrupt-controller;
> +			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
> +			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
> +			interrupts = <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		watchdog@17c10000 {
> +			compatible = "qcom,apss-wdt-sm6350", "qcom,kpss-wdt";
> +			reg = <0 0x17c10000 0 0x1000>;
> +			clocks = <&sleep_clk>;
> +			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		timer@17c20000 {
> +			compatible = "arm,armv7-timer-mem";
> +			reg = <0x0 0x17c20000 0x0 0x1000>;
> +			clock-frequency = <19200000>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +
> +			frame@17c21000 {
> +				frame-number = <0>;
> +				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> +					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c21000 0x0 0x1000>,
> +				      <0x0 0x17c22000 0x0 0x1000>;
> +			};
> +
> +			frame@17c23000 {
> +				frame-number = <1>;
> +				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c23000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@17c25000 {
> +				frame-number = <2>;
> +				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c25000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@17c27000 {
> +				frame-number = <3>;
> +				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c27000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@17c29000 {
> +				frame-number = <4>;
> +				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c29000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@17c2b000 {
> +				frame-number = <5>;
> +				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c2b000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +
> +			frame@17c2d000 {
> +				frame-number = <6>;
> +				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> +				reg = <0x0 0x17c2d000 0x0 0x1000>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		apps_rsc: rsc@18200000 {
> +			compatible = "qcom,rpmh-rsc";
> +			label = "apps_rsc";
> +			reg = <0x0 0x18200000 0x0 0x10000>,
> +				<0x0 0x18210000 0x0 0x10000>,
> +				<0x0 0x18220000 0x0 0x10000>;
> +			reg-names = "drv-0", "drv-1", "drv-2";
> +			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> +				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> +			qcom,tcs-offset = <0xd00>;
> +			qcom,drv-id = <2>;
> +			qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 3>,
> +					  <WAKE_TCS 3>, <CONTROL_TCS 1>;
> +		};
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		clock-frequency = <19200000>;
> +		interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +	};
> +};

-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v2 02/18] arm64: dts: qcom: Add SM6350 device tree

[Konrad Dybcio]

>> +
>> +        tcsr_mutex: hwlock@1f40000 {
>> +            compatible = "qcom,tcsr-mutex";
>> +            reg = <0x0 0x01f40000 0x0 0x40000>;
>> +            #hwlock-cells = <1>;
>> +        };
>> +
>> +        pdc: interrupt-controller@b220000 {
>> +            compatible = "qcom,sm6350-pdc", "qcom,pdc";
>> +            reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
>
> The second reg  0x17c000f0 is neither documented nor used in PDC irq chip driver. can you please remove it?
>
> Thanks,
> Maulik
>
Wouldn't it make more sense to keep it (like in other PDC-enabled SoCs' device trees) so that there's no

need to add it back when the driver gains support for spi_configure_type (I believe that's what it's used for)?


Konrad

Re: [PATCH v2 10/18] arm64: dts: qcom: sm6350: Add AOSS_QMP

[Maulik Shah]

Hi,

On 8/28/2021 6:48 PM, Konrad Dybcio wrote:
> Add a node for AOSS_QMP in preparation for remote processor enablement.
>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
>   arch/arm64/boot/dts/qcom/sm6350.dtsi | 11 +++++++++++
>   1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index 986d7fb01cbb..d903173b7dbc 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -537,6 +537,17 @@ tsens1: thermal-sensor@c265000 {
>   			#thermal-sensor-cells = <1>;
>   		};
>   
> +		aoss_qmp: power-controller@c300000 {
> +			compatible = "qcom,sm6350-aoss-qmp", "qcom,aoss-qmp";
> +			reg = <0 0x0c300000 0 0x1000>;

The QMP should only need 0x400 size [1].
Can you please change it so that when [1] goes in (and later when sleep 
stats enabled for sm6350 don't need to change size).

[1] 
https://patchwork.kernel.org/project/linux-arm-msm/patch/1621596371-26482-4-git-send-email-mkshah@codeaurora.org/

Thanks,
Maulik

> +			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
> +						     IRQ_TYPE_EDGE_RISING>;
> +			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> +			#clock-cells = <0>;
> +			#power-domain-cells = <1>;
> +		};
> +
>   		tlmm: pinctrl@f100000 {
>   			compatible = "qcom,sm6350-tlmm";
>   			reg = <0 0x0f100000 0 0x300000>;

-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v2 02/18] arm64: dts: qcom: Add SM6350 device tree

[Maulik Shah]

Hi,

On 8/28/2021 9:52 PM, Konrad Dybcio wrote:
>>> +
>>> +        tcsr_mutex: hwlock@1f40000 {
>>> +            compatible = "qcom,tcsr-mutex";
>>> +            reg = <0x0 0x01f40000 0x0 0x40000>;
>>> +            #hwlock-cells = <1>;
>>> +        };
>>> +
>>> +        pdc: interrupt-controller@b220000 {
>>> +            compatible = "qcom,sm6350-pdc", "qcom,pdc";
>>> +            reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x64>;
>> The second reg  0x17c000f0 is neither documented nor used in PDC irq chip driver. can you please remove it?
>>
>> Thanks,
>> Maulik
>>
> Wouldn't it make more sense to keep it (like in other PDC-enabled SoCs' device trees) so that there's no
>
> need to add it back when the driver gains support for spi_configure_type (I believe that's what it's used for)?
The second reg in some of the PDC enabled SoCs' went in since it may 
have slipped throgh code reviews when using downstream
patch as is on upstream.
Also the bindings document for PDC is still in txt, so yaml check could 
not catch the extra register which is not documented.

An attempt to add support for spi_configure_type [1] & [2] had 
suggestion either to access second reg via mailbox or
add another level of irqchip hierarchy between PDC to GIC to configure 
SPI type. Unless both [1] and [2] patch can go in as
PDC irqchip driver won't gain support to use it. (using mailbox approch 
will have mailbox driver to access this register and PDC node may 
mention which mailbox to use).

[1] 
https://patchwork.kernel.org/project/linux-arm-msm/patch/1568411962-1022-7-git-send-email-ilina@codeaurora.org/

[2] 
https://patchwork.kernel.org/project/linux-arm-msm/patch/1568411962-1022-8-git-send-email-ilina@codeaurora.org/

Thanks,
Maulik

>
>
> Konrad
>
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

Re: [PATCH v2 16/18] arm64: dts: qcom: sm6350: Add iommus property to USB1

[Bjorn Andersson]

On Sat 28 Aug 08:18 CDT 2021, Konrad Dybcio wrote:

> This is required for us to be able to access the associated registers, which
> are (on at least some devices) gated by default.
> 

Please either merge this with the patch that introduces the SMMU (which
I presume causes this "issue") or introduce the SMMU earlier in the
series.

Regards,
Bjorn

> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
>  arch/arm64/boot/dts/qcom/sm6350.dtsi | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index a3a1f0e63ace..95e69d9f8657 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -584,6 +584,7 @@ usb_1_dwc3: dwc3@a600000 {
>  				compatible = "snps,dwc3";
>  				reg = <0 0x0a600000 0 0xcd00>;
>  				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
> +				iommus = <&apps_smmu 0x540 0x0>;
>  				snps,dis_u2_susphy_quirk;
>  				snps,dis_enblslpm_quirk;
>  				snps,has-lpm-erratum;
> -- 
> 2.33.0
> 

Re: [PATCH v2 17/18] arm64: dts: qcom: Add device tree for Sony Xperia 10 III

[Bjorn Andersson]

On Sat 28 Aug 08:18 CDT 2021, Konrad Dybcio wrote:

> Add initial SM6350 SoC and Sony Xperia 10 III (PDX213, Lena platform) device
> trees. There is no sign of another Lena devices on the horizon, so a common
> DTSI is not created for now. 10 III features a Full HD OLED display and 5G
> support, among other nice things like USB3.
> 

Thanks for the series, looks quite nice, so please respin with the few
small modifications noted in the reviews.

> The bootloader is VERY unpleasant, to get a bootable setup you have to run:
> 
> mkbootimg --kernel arch/arm64/boot/Image.gz --ramdisk [some initrd] \
> --dtb arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dtb \
> --cmdline "[some cmdline]" --base 0 --kernel_offset 0x8000 \
> --ramdisk_offset 0x1000000 --dtb_offset 0x1f00000 --os_version 11 \
> --os_patch_level "2021-08" --tags_offset 0x100 --pagesize 4096 \
> --header_version 2 -o mainline.img
> 
> adb reboot bootloader
> 
> // You have to either pull vbmeta{"","_system"} from
> // /dev/block/bootdevice/by-name/ or build one as a part of AOSP build process
> fastboot --disable-verity --disable-verification flash vbmeta vbmeta.img
> fastboot --disable-verity --disable-verification flash vbmeta_system \
> vbmeta_system.img
> 
> fastboot flash boot mainline.img
> fastboot erase dtbo // This will take approx 70s...

I always assumed that erase was broken when it took more than 5 seconds
to clear the dtbo partition(s). So I always just flash a few kB of
/dev/zero.

Regards,
Bjorn

> fastboot reboot
> 
> Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |  1 +
>  .../qcom/sm6350-sony-xperia-lena-pdx213.dts   | 57 +++++++++++++++++++
>  2 files changed, 58 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 5bbeb058e1f2..d1ace2541ce1 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -78,6 +78,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-akatsuki.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-apollo.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-hdk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-microsoft-surface-duo.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sm8150-mtp.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> new file mode 100644
> index 000000000000..a26c23754f5d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
> + */
> +/dts-v1/;
> +
> +#include "sm6350.dtsi"
> +
> +/ {
> +	model = "Sony Xperia 10 III";
> +	compatible = "sony,pdx213", "qcom,sm6350";
> +	qcom,msm-id = <434 0x10000>, <459 0x10000>;
> +	qcom,board-id = <0x1000B 0>;
> +
> +	chosen {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		framebuffer: framebuffer@a0000000 {
> +			compatible = "simple-framebuffer";
> +			reg = <0 0xa0000000 0 0x2300000>;
> +			width = <1080>;
> +			height = <2520>;
> +			stride = <(1080 * 4)>;
> +			format = "a8r8g8b8";
> +			clocks = <&gcc GCC_DISP_AXI_CLK>;
> +		};
> +	};
> +};
> +
> +&sdhc_2 {
> +	status = "okay";
> +
> +	cd-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <13 4>, <45 2>, <56 2>;
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> +	maximum-speed = "super-speed";
> +	dr_mode = "peripheral";
> +};
> +
> +&usb_1_hsphy {
> +	status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> +	status = "okay";
> +};
> -- 
> 2.33.0
>