All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v4 0/4] arm64: meson: add support for JetHub D1/H1
@ 2021-09-07  9:56 ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.      
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Changes from v3:
- add pinctrl for spicc1 in meson-axg-jethome-jethub-j100.dts

Changes from v2:
- add new vendor to vendor-prefixes
- sync board compatible dt-bindings to jethome,jethub-*
- fix efuse fields
- fix gpio-line-names
- fix spaces and blank lines
- recheck via checkpatch
 
Changes from v1:
- rearrange patches
- add SPDX license and copyright header
- remove attributes without bindings
- small fixes with spaces

Vyacheslav Bocharov (4):
  dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
  dt-bindings: vendor-prefixes: add jethome prefix
  arm64: dts: meson-gxl: add support for JetHub H1
  arm64: dts: meson-axg: add support for JetHub D1

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
 5 files changed, 603 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

-- 
2.30.2


^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 0/4] arm64: meson: add support for JetHub D1/H1
@ 2021-09-07  9:56 ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.      
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Changes from v3:
- add pinctrl for spicc1 in meson-axg-jethome-jethub-j100.dts

Changes from v2:
- add new vendor to vendor-prefixes
- sync board compatible dt-bindings to jethome,jethub-*
- fix efuse fields
- fix gpio-line-names
- fix spaces and blank lines
- recheck via checkpatch
 
Changes from v1:
- rearrange patches
- add SPDX license and copyright header
- remove attributes without bindings
- small fixes with spaces

Vyacheslav Bocharov (4):
  dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
  dt-bindings: vendor-prefixes: add jethome prefix
  arm64: dts: meson-gxl: add support for JetHub H1
  arm64: dts: meson-axg: add support for JetHub D1

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
 5 files changed, 603 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 0/4] arm64: meson: add support for JetHub D1/H1
@ 2021-09-07  9:56 ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.      
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Changes from v3:
- add pinctrl for spicc1 in meson-axg-jethome-jethub-j100.dts

Changes from v2:
- add new vendor to vendor-prefixes
- sync board compatible dt-bindings to jethome,jethub-*
- fix efuse fields
- fix gpio-line-names
- fix spaces and blank lines
- recheck via checkpatch
 
Changes from v1:
- rearrange patches
- add SPDX license and copyright header
- remove attributes without bindings
- small fixes with spaces

Vyacheslav Bocharov (4):
  dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
  dt-bindings: vendor-prefixes: add jethome prefix
  arm64: dts: meson-gxl: add support for JetHub H1
  arm64: dts: meson-axg: add support for JetHub D1

 .../devicetree/bindings/arm/amlogic.yaml      |   2 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/amlogic/Makefile          |   2 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
 5 files changed, 603 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 24+ messages in thread

* [PATCH v4 1/4] dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
  2021-09-07  9:56 ` Vyacheslav Bocharov
  (?)
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree, Rob Herring

JetHome is a series of home automation controllers:
- Jethub D1 based on Amlogic A113X
- Jethub H1 based on AmLogic S905W

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 6423377710ee..b223d7829c3d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -86,6 +86,7 @@ properties:
           - enum:
               - amlogic,p281
               - oranth,tx3-mini
+              - jethome,jethub-j80
           - const: amlogic,s905w
           - const: amlogic,meson-gxl
 
@@ -133,6 +134,7 @@ properties:
         items:
           - enum:
               - amlogic,s400
+              - jethome,jethub-j100
           - const: amlogic,a113d
           - const: amlogic,meson-axg
 
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 1/4] dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree, Rob Herring

JetHome is a series of home automation controllers:
- Jethub D1 based on Amlogic A113X
- Jethub H1 based on AmLogic S905W

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 6423377710ee..b223d7829c3d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -86,6 +86,7 @@ properties:
           - enum:
               - amlogic,p281
               - oranth,tx3-mini
+              - jethome,jethub-j80
           - const: amlogic,s905w
           - const: amlogic,meson-gxl
 
@@ -133,6 +134,7 @@ properties:
         items:
           - enum:
               - amlogic,s400
+              - jethome,jethub-j100
           - const: amlogic,a113d
           - const: amlogic,meson-axg
 
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 1/4] dt-bindings: arm: amlogic: add bindings for Jethub D1/H1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree, Rob Herring

JetHome is a series of home automation controllers:
- Jethub D1 based on Amlogic A113X
- Jethub H1 based on AmLogic S905W

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/arm/amlogic.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml
index 6423377710ee..b223d7829c3d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@@ -86,6 +86,7 @@ properties:
           - enum:
               - amlogic,p281
               - oranth,tx3-mini
+              - jethome,jethub-j80
           - const: amlogic,s905w
           - const: amlogic,meson-gxl
 
@@ -133,6 +134,7 @@ properties:
         items:
           - enum:
               - amlogic,s400
+              - jethome,jethub-j100
           - const: amlogic,a113d
           - const: amlogic,meson-axg
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
  2021-09-07  9:56 ` Vyacheslav Bocharov
  (?)
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 3/4] arm64: dts: meson-gxl: add support for JetHub H1
  2021-09-07  9:56 ` Vyacheslav Bocharov
  (?)
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:

- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++++++++
 2 files changed, 242 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..2c3ce7c401a5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..6eafb908695f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+	model = "JetHome JetHub J80";
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x1000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_A;    /* Bluetooth */
+		serial2 = &uart_AO_B; /* Wireless module 1 */
+		serial3 = &uart_C;    /* Wireless module 2 */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&efuse {
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@C {
+		reg = <0xc 0x6>;
+	};
+};
+
+&sn {
+	reg = <0x32 0x20>;
+};
+
+&eth_mac {
+	reg = <0x0 0x6>;
+};
+
+&bid {
+	reg = <0x12 0x20>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+	status = "okay";
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_C {
+	status = "okay";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_b_pins>;
+
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 3/4] arm64: dts: meson-gxl: add support for JetHub H1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:

- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++++++++
 2 files changed, 242 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..2c3ce7c401a5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..6eafb908695f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+	model = "JetHome JetHub J80";
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x1000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_A;    /* Bluetooth */
+		serial2 = &uart_AO_B; /* Wireless module 1 */
+		serial3 = &uart_C;    /* Wireless module 2 */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&efuse {
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@C {
+		reg = <0xc 0x6>;
+	};
+};
+
+&sn {
+	reg = <0x32 0x20>;
+};
+
+&eth_mac {
+	reg = <0x0 0x6>;
+};
+
+&bid {
+	reg = <0x12 0x20>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+	status = "okay";
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_C {
+	status = "okay";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_b_pins>;
+
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 3/4] arm64: dts: meson-gxl: add support for JetHub H1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:

- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++++++++
 2 files changed, 242 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index faa0a79a34f5..2c3ce7c401a5 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -38,6 +38,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 000000000000..6eafb908695f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+	model = "JetHome JetHub J80";
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x1000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_A;    /* Bluetooth */
+		serial2 = &uart_AO_B; /* Wireless module 1 */
+		serial3 = &uart_C;    /* Wireless module 2 */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&efuse {
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@C {
+		reg = <0xc 0x6>;
+	};
+};
+
+&sn {
+	reg = <0x32 0x20>;
+};
+
+&eth_mac {
+	reg = <0x0 0x6>;
+};
+
+&bid {
+	reg = <0x12 0x20>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+	status = "okay";
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_C {
+	status = "okay";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_b_pins>;
+
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
  2021-09-07  9:56 ` Vyacheslav Bocharov
  (?)
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
  Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 2 files changed, 357 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..ecffc90d9884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub J100";
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 1024MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		cpu_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&cpu_passive>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+
+			map1 {
+				trip = <&cpu_hot>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
  Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 2 files changed, 357 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..ecffc90d9884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub J100";
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 1024MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		cpu_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&cpu_passive>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+
+			map1 {
+				trip = <&cpu_hot>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-07  9:56   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-07  9:56 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
  Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
  and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 arch/arm64/boot/dts/amlogic/Makefile          |   1 +
 .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
 2 files changed, 357 insertions(+)
 create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 2c3ce7c401a5..3ba6f58b9833 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 000000000000..ecffc90d9884
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,356 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub J100";
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 1024MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		cpu_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&cpu_passive>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+
+			map1 {
+				trip = <&cpu_hot>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
  2021-09-07  9:56   ` Vyacheslav Bocharov
  (?)
@ 2021-09-08  6:56     ` Neil Armstrong
  -1 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2021-09-08  6:56 UTC (permalink / raw)
  To: Vyacheslav Bocharov, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Hi,

On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
>   Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
>   and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>  .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
>  2 files changed, 357 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2c3ce7c401a5..3ba6f58b9833 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
>  # SPDX-License-Identifier: GPL-2.0
>  dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> new file mode 100644
> index 000000000000..ecffc90d9884
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -0,0 +1,356 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <ak@tvip.ru>
> + * Author: Alexey Shevelkin <ash@tvip.ru>
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> +	model = "JetHome JetHub J100";
> +	aliases {
> +		serial0 = &uart_AO;   /* Console */
> +		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	/* 1024MB RAM */
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		linux,cma {
> +			size = <0x0 0x400000>;
> +		};
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_5v: regulator-vcc_5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	usb_pwr: regulator-usb_pwr {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> +	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&scpi_sensors 0>;
> +			trips {
> +				cpu_passive: cpu-passive {
> +					temperature = <70000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "passive";
> +				};
> +
> +				cpu_hot: cpu-hot {
> +					temperature = <80000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "hot";
> +				};
> +
> +				cpu_critical: cpu-critical {
> +					temperature = <100000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		cpu_cooling_maps: cooling-maps {
> +			map0 {
> +				trip = <&cpu_passive>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +
> +			map1 {
> +				trip = <&cpu_hot>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +		};
> +	};
> +};
> +
> +&efuse {
> +	sn: sn@32 {
> +		reg = <0x32 0x20>;
> +	};
> +
> +	eth_mac: eth_mac@0 {
> +		reg = <0x0 0x6>;
> +	};
> +
> +	bt_mac: bt_mac@6 {
> +		reg = <0x6 0x6>;
> +	};
> +
> +	wifi_mac: wifi_mac@c {
> +		reg = <0xc 0x6>;
> +	};
> +
> +	bid: bid@12 {
> +		reg = <0x12 0x20>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	pinctrl-0 = <&eth_rmii_x_pins>;
> +	pinctrl-names = "default";
> +	phy-handle = <&eth_phy0>;
> +	phy-mode = "rmii";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> +		eth_phy0: ethernet-phy@0 {
> +			/* compatible = "ethernet-phy-id0243.0c54";*/
> +			max-speed = <100>;
> +			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> +	status = "okay";
> +	pinctrl-0 = <&i2c1_z_pins>;
> +	pinctrl-names = "default";
> +
> +	/* RTC */
> +	pcf8563: pcf8563@51 {
> +		compatible = "nxp,pcf8563";
> +		reg = <0x51>;
> +		status = "okay";
> +	};
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_a_x20_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	sd-uhs-sdr104;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +/* UART Console */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_b_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb {
> +	status = "okay";
> +	phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> +	status = "okay";
> +	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&gpio {
> +	gpio-line-names =
> +		"", "", "", "", "", // 0 - 4
> +		"", "", "", "", "", // 5 - 9
> +		"UserButton", "", "", "", "", // 10 - 14
> +		"", "", "", "", "", // 15 - 19
> +		"", "", "", "", "", // 20 - 24
> +		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> +		"Output1", "", "", "", "", // 30 - 34
> +		"", "ZigBeeBOOT", "", "", "", // 35 - 39
> +		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> +		"Input2", "Input1", "", "", "", // 45 - 49
> +		"", "", "", "", "", // 50 - 54
> +		"", "", "", "", "", // 55 - 59
> +		"", "", "", "", "", // 60 - 64
> +		"", "", "", "", "", // 65 - 69
> +		"", "", "", "", "", // 70 - 74
> +		"", "", "", "", "", // 75 - 79
> +		"", "", "", "", "", // 80 - 84
> +		"", ""; // 85-86
> +};
> +
> +&cpu0 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> +	#cooling-cells = <2>;
> +};
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Thanks,
Neil

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-08  6:56     ` Neil Armstrong
  0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2021-09-08  6:56 UTC (permalink / raw)
  To: Vyacheslav Bocharov, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Hi,

On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
>   Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
>   and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>  .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
>  2 files changed, 357 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2c3ce7c401a5..3ba6f58b9833 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
>  # SPDX-License-Identifier: GPL-2.0
>  dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> new file mode 100644
> index 000000000000..ecffc90d9884
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -0,0 +1,356 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <ak@tvip.ru>
> + * Author: Alexey Shevelkin <ash@tvip.ru>
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> +	model = "JetHome JetHub J100";
> +	aliases {
> +		serial0 = &uart_AO;   /* Console */
> +		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	/* 1024MB RAM */
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		linux,cma {
> +			size = <0x0 0x400000>;
> +		};
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_5v: regulator-vcc_5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	usb_pwr: regulator-usb_pwr {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> +	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&scpi_sensors 0>;
> +			trips {
> +				cpu_passive: cpu-passive {
> +					temperature = <70000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "passive";
> +				};
> +
> +				cpu_hot: cpu-hot {
> +					temperature = <80000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "hot";
> +				};
> +
> +				cpu_critical: cpu-critical {
> +					temperature = <100000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		cpu_cooling_maps: cooling-maps {
> +			map0 {
> +				trip = <&cpu_passive>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +
> +			map1 {
> +				trip = <&cpu_hot>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +		};
> +	};
> +};
> +
> +&efuse {
> +	sn: sn@32 {
> +		reg = <0x32 0x20>;
> +	};
> +
> +	eth_mac: eth_mac@0 {
> +		reg = <0x0 0x6>;
> +	};
> +
> +	bt_mac: bt_mac@6 {
> +		reg = <0x6 0x6>;
> +	};
> +
> +	wifi_mac: wifi_mac@c {
> +		reg = <0xc 0x6>;
> +	};
> +
> +	bid: bid@12 {
> +		reg = <0x12 0x20>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	pinctrl-0 = <&eth_rmii_x_pins>;
> +	pinctrl-names = "default";
> +	phy-handle = <&eth_phy0>;
> +	phy-mode = "rmii";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> +		eth_phy0: ethernet-phy@0 {
> +			/* compatible = "ethernet-phy-id0243.0c54";*/
> +			max-speed = <100>;
> +			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> +	status = "okay";
> +	pinctrl-0 = <&i2c1_z_pins>;
> +	pinctrl-names = "default";
> +
> +	/* RTC */
> +	pcf8563: pcf8563@51 {
> +		compatible = "nxp,pcf8563";
> +		reg = <0x51>;
> +		status = "okay";
> +	};
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_a_x20_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	sd-uhs-sdr104;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +/* UART Console */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_b_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb {
> +	status = "okay";
> +	phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> +	status = "okay";
> +	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&gpio {
> +	gpio-line-names =
> +		"", "", "", "", "", // 0 - 4
> +		"", "", "", "", "", // 5 - 9
> +		"UserButton", "", "", "", "", // 10 - 14
> +		"", "", "", "", "", // 15 - 19
> +		"", "", "", "", "", // 20 - 24
> +		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> +		"Output1", "", "", "", "", // 30 - 34
> +		"", "ZigBeeBOOT", "", "", "", // 35 - 39
> +		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> +		"Input2", "Input1", "", "", "", // 45 - 49
> +		"", "", "", "", "", // 50 - 54
> +		"", "", "", "", "", // 55 - 59
> +		"", "", "", "", "", // 60 - 64
> +		"", "", "", "", "", // 65 - 69
> +		"", "", "", "", "", // 70 - 74
> +		"", "", "", "", "", // 75 - 79
> +		"", "", "", "", "", // 80 - 84
> +		"", ""; // 85-86
> +};
> +
> +&cpu0 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> +	#cooling-cells = <2>;
> +};
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Thanks,
Neil

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-08  6:56     ` Neil Armstrong
  0 siblings, 0 replies; 24+ messages in thread
From: Neil Armstrong @ 2021-09-08  6:56 UTC (permalink / raw)
  To: Vyacheslav Bocharov, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

Hi,

On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> controller with the following features:
> - DIN Rail Mounting
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB LPDDR4
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
>   Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
>   and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>  arch/arm64/boot/dts/amlogic/Makefile          |   1 +
>  .../amlogic/meson-axg-jethome-jethub-j100.dts | 356 ++++++++++++++++++
>  2 files changed, 357 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> 
> diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
> index 2c3ce7c401a5..3ba6f58b9833 100644
> --- a/arch/arm64/boot/dts/amlogic/Makefile
> +++ b/arch/arm64/boot/dts/amlogic/Makefile
> @@ -1,5 +1,6 @@
>  # SPDX-License-Identifier: GPL-2.0
>  dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
> +dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
>  dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
> diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> new file mode 100644
> index 000000000000..ecffc90d9884
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
> @@ -0,0 +1,356 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
> + * Copyright (c) 2020 JetHome
> + * Author: Aleksandr Kazantsev <ak@tvip.ru>
> + * Author: Alexey Shevelkin <ash@tvip.ru>
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +/dts-v1/;
> +
> +#include "meson-axg.dtsi"
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> +
> +/ {
> +	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
> +	model = "JetHome JetHub J100";
> +	aliases {
> +		serial0 = &uart_AO;   /* Console */
> +		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
> +		ethernet0 = &ethmac;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	/* 1024MB RAM */
> +	memory@0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x40000000>;
> +	};
> +
> +	reserved-memory {
> +		linux,cma {
> +			size = <0x0 0x400000>;
> +		};
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vcc_5v: regulator-vcc_5v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC5V";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		vin-supply = <&vddao_3v3>;
> +		regulator-always-on;
> +	};
> +
> +	usb_pwr: regulator-usb_pwr {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB_PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v>;
> +		regulator-always-on;
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
> +	};
> +
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <250>;
> +			polling-delay = <1000>;
> +			thermal-sensors = <&scpi_sensors 0>;
> +			trips {
> +				cpu_passive: cpu-passive {
> +					temperature = <70000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "passive";
> +				};
> +
> +				cpu_hot: cpu-hot {
> +					temperature = <80000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "hot";
> +				};
> +
> +				cpu_critical: cpu-critical {
> +					temperature = <100000>; /* millicelsius */
> +					hysteresis = <2000>; /* millicelsius */
> +					type = "critical";
> +				};
> +			};
> +		};
> +
> +		cpu_cooling_maps: cooling-maps {
> +			map0 {
> +				trip = <&cpu_passive>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +
> +			map1 {
> +				trip = <&cpu_hot>;
> +				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +			};
> +		};
> +	};
> +};
> +
> +&efuse {
> +	sn: sn@32 {
> +		reg = <0x32 0x20>;
> +	};
> +
> +	eth_mac: eth_mac@0 {
> +		reg = <0x0 0x6>;
> +	};
> +
> +	bt_mac: bt_mac@6 {
> +		reg = <0x6 0x6>;
> +	};
> +
> +	wifi_mac: wifi_mac@c {
> +		reg = <0xc 0x6>;
> +	};
> +
> +	bid: bid@12 {
> +		reg = <0x12 0x20>;
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +	pinctrl-0 = <&eth_rmii_x_pins>;
> +	pinctrl-names = "default";
> +	phy-handle = <&eth_phy0>;
> +	phy-mode = "rmii";
> +
> +	mdio {
> +		compatible = "snps,dwmac-mdio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
> +		eth_phy0: ethernet-phy@0 {
> +			/* compatible = "ethernet-phy-id0243.0c54";*/
> +			max-speed = <100>;
> +			reg = <0>;
> +
> +			reset-assert-us = <10000>;
> +			reset-deassert-us = <10000>;
> +			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +/* Internal I2C bus (on CPU module) */
> +&i2c1 {
> +	status = "okay";
> +	pinctrl-0 = <&i2c1_z_pins>;
> +	pinctrl-names = "default";
> +
> +	/* RTC */
> +	pcf8563: pcf8563@51 {
> +		compatible = "nxp,pcf8563";
> +		reg = <0x51>;
> +		status = "okay";
> +	};
> +};
> +
> +/* Peripheral I2C bus (on motherboard) */
> +&i2c_AO {
> +	status = "okay";
> +	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&pwm_ab {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_a_x20_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* wifi module */
> +&sd_emmc_b {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-1 = <&sdio_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	sd-uhs-sdr104;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: wifi@1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* emmc storage */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
> +	pinctrl-1 = <&emmc_clk_gate_pins>;
> +	pinctrl-names = "default", "clk-gate";
> +
> +	bus-width = <8>;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* UART Bluetooth */
> +&uart_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +
> +	bluetooth {
> +		compatible = "brcm,bcm43438-bt";
> +		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> +
> +/* UART Console */
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +/* UART Wireless module */
> +&uart_AO_B {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_b_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&usb {
> +	status = "okay";
> +	phy-supply = <&usb_pwr>;
> +};
> +
> +&spicc1 {
> +	status = "okay";
> +	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&gpio {
> +	gpio-line-names =
> +		"", "", "", "", "", // 0 - 4
> +		"", "", "", "", "", // 5 - 9
> +		"UserButton", "", "", "", "", // 10 - 14
> +		"", "", "", "", "", // 15 - 19
> +		"", "", "", "", "", // 20 - 24
> +		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
> +		"Output1", "", "", "", "", // 30 - 34
> +		"", "ZigBeeBOOT", "", "", "", // 35 - 39
> +		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
> +		"Input2", "Input1", "", "", "", // 45 - 49
> +		"", "", "", "", "", // 50 - 54
> +		"", "", "", "", "", // 55 - 59
> +		"", "", "", "", "", // 60 - 64
> +		"", "", "", "", "", // 65 - 69
> +		"", "", "", "", "", // 70 - 74
> +		"", "", "", "", "", // 75 - 79
> +		"", "", "", "", "", // 80 - 84
> +		"", ""; // 85-86
> +};
> +
> +&cpu0 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu1 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu2 {
> +	#cooling-cells = <2>;
> +};
> +
> +&cpu3 {
> +	#cooling-cells = <2>;
> +};
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

Thanks,
Neil

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Resend: [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
  2021-09-07  9:56 ` Vyacheslav Bocharov
  (?)
@ 2021-09-09 10:11   ` Vyacheslav Bocharov
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-09 10:11 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski,
	Shawn Guo, Oleksij Rempel, Sam Ravnborg
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
	Vyacheslav Bocharov

From: Vyacheslav Bocharov <devel@lexina.in>

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 24+ messages in thread

* Resend: [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
@ 2021-09-09 10:11   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-09 10:11 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski,
	Shawn Guo, Oleksij Rempel, Sam Ravnborg
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
	Vyacheslav Bocharov

From: Vyacheslav Bocharov <devel@lexina.in>

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* Resend: [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix
@ 2021-09-09 10:11   ` Vyacheslav Bocharov
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-09 10:11 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman, Rob Herring, Krzysztof Kozlowski,
	Shawn Guo, Oleksij Rempel, Sam Ravnborg
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel, devicetree,
	Vyacheslav Bocharov

From: Vyacheslav Bocharov <devel@lexina.in>

JetHome is trademark of IP Sokolov P.A., manufacturer of home automation
devices.

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index a867f7102c35..c52f0d3261bb 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -577,6 +577,8 @@ patternProperties:
     description: JEDEC Solid State Technology Association
   "^jesurun,.*":
     description: Shenzhen Jesurun Electronics Business Dept.
+  "^jethome,.*":
+    description: JetHome (IP Sokolov P.A.)
   "^jianda,.*":
     description: Jiandangjing Technology Co., Ltd.
   "^kam,.*":
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
  2021-09-08  6:56     ` Neil Armstrong
  (?)
@ 2021-09-09 10:14       ` Vyacheslav
  -1 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav @ 2021-09-09 10:14 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

08.09.2021 09:56, Neil Armstrong wrote:
> Hi,
> 
> On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> 
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> 
> Thanks,
> Neil

Thanks.

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-09 10:14       ` Vyacheslav
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav @ 2021-09-09 10:14 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

08.09.2021 09:56, Neil Armstrong wrote:
> Hi,
> 
> On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> 
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> 
> Thanks,
> Neil

Thanks.

_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic

^ permalink raw reply	[flat|nested] 24+ messages in thread

* Re: [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1
@ 2021-09-09 10:14       ` Vyacheslav
  0 siblings, 0 replies; 24+ messages in thread
From: Vyacheslav @ 2021-09-09 10:14 UTC (permalink / raw)
  To: Neil Armstrong, Kevin Hilman
  Cc: linux-amlogic, linux-arm-kernel, linux-kernel

08.09.2021 09:56, Neil Armstrong wrote:
> Hi,
> 
> On 07/09/2021 11:56, Vyacheslav Bocharov wrote:
>> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
> 
> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
> 
> Thanks,
> Neil

Thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply	[flat|nested] 24+ messages in thread

end of thread, other threads:[~2021-09-09 10:16 UTC | newest]

Thread overview: 24+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-07  9:56 [PATCH v4 0/4] arm64: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-07  9:56 ` Vyacheslav Bocharov
2021-09-07  9:56 ` Vyacheslav Bocharov
2021-09-07  9:56 ` [PATCH v4 1/4] dt-bindings: arm: amlogic: add bindings for Jethub D1/H1 Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56 ` [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56 ` [PATCH v4 3/4] arm64: dts: meson-gxl: add support for JetHub H1 Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56 ` [PATCH v4 4/4] arm64: dts: meson-axg: add support for JetHub D1 Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-07  9:56   ` Vyacheslav Bocharov
2021-09-08  6:56   ` Neil Armstrong
2021-09-08  6:56     ` Neil Armstrong
2021-09-08  6:56     ` Neil Armstrong
2021-09-09 10:14     ` Vyacheslav
2021-09-09 10:14       ` Vyacheslav
2021-09-09 10:14       ` Vyacheslav
2021-09-09 10:11 ` Resend: [PATCH v4 2/4] dt-bindings: vendor-prefixes: add jethome prefix Vyacheslav Bocharov
2021-09-09 10:11   ` Vyacheslav Bocharov
2021-09-09 10:11   ` Vyacheslav Bocharov

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.