All of lore.kernel.org
 help / color / mirror / Atom feed
From: <Ajay.Kathat@microchip.com>
To: <linux-wireless@vger.kernel.org>
Cc: <Claudiu.Beznea@microchip.com>, <Ajay.Kathat@microchip.com>
Subject: [PATCH v2 04/11] wilc1000: configure registers to handle chip wakeup sequence
Date: Thu, 16 Sep 2021 16:49:19 +0000	[thread overview]
Message-ID: <20210916164902.74629-5-ajay.kathat@microchip.com> (raw)
In-Reply-To: <20210916164902.74629-1-ajay.kathat@microchip.com>

From: Ajay Singh <ajay.kathat@microchip.com>

Use the correct sequence to configure clockless registers for chip wake-up.
The following sequence is expected from WILC chip for wakeup:
 - set wakeup bit in wakeup_reg register
 - after setting the wakeup bit, read back the clock status bit for wakeup
   complete.

For SDIO/SPI modules, the wakeup sequence is the same except uses different
register values so refactored the code to use common function for both
SDIO/SPI bus.

Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
---
 .../wireless/microchip/wilc1000/cfg80211.c    |  1 -
 .../net/wireless/microchip/wilc1000/netdev.h  |  1 -
 .../net/wireless/microchip/wilc1000/wlan.c    | 98 ++++++++++---------
 .../net/wireless/microchip/wilc1000/wlan.h    |  2 +
 .../net/wireless/microchip/wilc1000/wlan_if.h |  6 --
 5 files changed, 53 insertions(+), 55 deletions(-)

diff --git a/drivers/net/wireless/microchip/wilc1000/cfg80211.c b/drivers/net/wireless/microchip/wilc1000/cfg80211.c
index 75160ab3914a..91a471f3b1c8 100644
--- a/drivers/net/wireless/microchip/wilc1000/cfg80211.c
+++ b/drivers/net/wireless/microchip/wilc1000/cfg80211.c
@@ -1726,7 +1726,6 @@ int wilc_cfg80211_init(struct wilc **wilc, struct device *dev, int io_type,
 	*wilc = wl;
 	wl->io_type = io_type;
 	wl->hif_func = ops;
-	wl->chip_ps_state = WILC_CHIP_WAKEDUP;
 
 	for (i = 0; i < NQUEUES; i++)
 		INIT_LIST_HEAD(&wl->txq[i].txq_head.list);
diff --git a/drivers/net/wireless/microchip/wilc1000/netdev.h b/drivers/net/wireless/microchip/wilc1000/netdev.h
index a39c62a20f04..79f73a72da57 100644
--- a/drivers/net/wireless/microchip/wilc1000/netdev.h
+++ b/drivers/net/wireless/microchip/wilc1000/netdev.h
@@ -265,7 +265,6 @@ struct wilc {
 	bool suspend_event;
 
 	struct workqueue_struct *hif_workqueue;
-	enum chip_ps_states chip_ps_state;
 	struct wilc_cfg cfg;
 	void *bus_data;
 	struct net_device *monitor_dev;
diff --git a/drivers/net/wireless/microchip/wilc1000/wlan.c b/drivers/net/wireless/microchip/wilc1000/wlan.c
index 200a103a0a85..1aad537c468f 100644
--- a/drivers/net/wireless/microchip/wilc1000/wlan.c
+++ b/drivers/net/wireless/microchip/wilc1000/wlan.c
@@ -10,6 +10,8 @@
 #include "cfg80211.h"
 #include "wlan_cfg.h"
 
+#define WAKE_UP_TRIAL_RETRY		10000
+
 static inline bool is_wilc1000(u32 id)
 {
 	return (id & (~WILC_CHIP_REV_FIELD)) == WILC_1000_BASE_ID;
@@ -611,60 +613,62 @@ EXPORT_SYMBOL_GPL(chip_allow_sleep);
 
 void chip_wakeup(struct wilc *wilc)
 {
-	u32 reg, clk_status_reg;
-	const struct wilc_hif_func *h = wilc->hif_func;
-
-	if (wilc->io_type == WILC_HIF_SPI) {
-		do {
-			h->hif_read_reg(wilc, WILC_SPI_WAKEUP_REG, &reg);
-			h->hif_write_reg(wilc, WILC_SPI_WAKEUP_REG,
-					 reg | WILC_SPI_WAKEUP_BIT);
-			h->hif_write_reg(wilc, WILC_SPI_WAKEUP_REG,
-					 reg & ~WILC_SPI_WAKEUP_BIT);
-
-			do {
-				usleep_range(2000, 2500);
-				wilc_get_chipid(wilc, true);
-			} while (wilc_get_chipid(wilc, true) == 0);
-		} while (wilc_get_chipid(wilc, true) == 0);
-	} else if (wilc->io_type == WILC_HIF_SDIO) {
-		h->hif_write_reg(wilc, WILC_SDIO_HOST_TO_FW_REG,
-				 WILC_SDIO_HOST_TO_FW_BIT);
-		usleep_range(200, 400);
-		h->hif_read_reg(wilc, WILC_SDIO_WAKEUP_REG, &reg);
-		do {
-			h->hif_write_reg(wilc, WILC_SDIO_WAKEUP_REG,
-					 reg | WILC_SDIO_WAKEUP_BIT);
-			h->hif_read_reg(wilc, WILC_SDIO_CLK_STATUS_REG,
-					&clk_status_reg);
-
-			while (!(clk_status_reg & WILC_SDIO_CLK_STATUS_BIT)) {
-				usleep_range(2000, 2500);
+	u32 ret = 0;
+	u32 clk_status_val = 0, trials = 0;
+	u32 wakeup_reg, wakeup_bit;
+	u32 clk_status_reg, clk_status_bit;
+	u32 to_host_from_fw_reg, to_host_from_fw_bit;
+	u32 from_host_to_fw_reg, from_host_to_fw_bit;
+	const struct wilc_hif_func *hif_func = wilc->hif_func;
 
-				h->hif_read_reg(wilc, WILC_SDIO_CLK_STATUS_REG,
-						&clk_status_reg);
-			}
-			if (!(clk_status_reg & WILC_SDIO_CLK_STATUS_BIT)) {
-				h->hif_write_reg(wilc, WILC_SDIO_WAKEUP_REG,
-						 reg & ~WILC_SDIO_WAKEUP_BIT);
-			}
-		} while (!(clk_status_reg & WILC_SDIO_CLK_STATUS_BIT));
+	if (wilc->io_type == WILC_HIF_SDIO) {
+		wakeup_reg = WILC_SDIO_WAKEUP_REG;
+		wakeup_bit = WILC_SDIO_WAKEUP_BIT;
+		clk_status_reg = WILC_SDIO_CLK_STATUS_REG;
+		clk_status_bit = WILC_SDIO_CLK_STATUS_BIT;
+		from_host_to_fw_reg = WILC_SDIO_HOST_TO_FW_REG;
+		from_host_to_fw_bit = WILC_SDIO_HOST_TO_FW_BIT;
+		to_host_from_fw_reg = WILC_SDIO_FW_TO_HOST_REG;
+		to_host_from_fw_bit = WILC_SDIO_FW_TO_HOST_BIT;
+	} else {
+		wakeup_reg = WILC_SPI_WAKEUP_REG;
+		wakeup_bit = WILC_SPI_WAKEUP_BIT;
+		clk_status_reg = WILC_SPI_CLK_STATUS_REG;
+		clk_status_bit = WILC_SPI_CLK_STATUS_BIT;
+		from_host_to_fw_reg = WILC_SPI_HOST_TO_FW_REG;
+		from_host_to_fw_bit = WILC_SPI_HOST_TO_FW_BIT;
+		to_host_from_fw_reg = WILC_SPI_FW_TO_HOST_REG;
+		to_host_from_fw_bit = WILC_SPI_FW_TO_HOST_BIT;
 	}
 
-	if (wilc->chip_ps_state == WILC_CHIP_SLEEPING_MANUAL) {
-		if (wilc_get_chipid(wilc, false) < WILC_1000_BASE_ID_2B) {
-			u32 val32;
+	/* indicate host wakeup */
+	ret = hif_func->hif_write_reg(wilc, from_host_to_fw_reg,
+				      from_host_to_fw_bit);
+	if (ret)
+		return;
 
-			h->hif_read_reg(wilc, WILC_REG_4_TO_1_RX, &val32);
-			val32 |= BIT(6);
-			h->hif_write_reg(wilc, WILC_REG_4_TO_1_RX, val32);
+	/* Set wake-up bit */
+	ret = hif_func->hif_write_reg(wilc, wakeup_reg,
+				      wakeup_bit);
+	if (ret)
+		return;
 
-			h->hif_read_reg(wilc, WILC_REG_4_TO_1_TX_BANK0, &val32);
-			val32 |= BIT(6);
-			h->hif_write_reg(wilc, WILC_REG_4_TO_1_TX_BANK0, val32);
+	while (trials < WAKE_UP_TRIAL_RETRY) {
+		ret = hif_func->hif_read_reg(wilc, clk_status_reg,
+					     &clk_status_val);
+		if (ret) {
+			pr_err("Bus error %d %x\n", ret, clk_status_val);
+			return;
 		}
+		if (clk_status_val & clk_status_bit)
+			break;
+
+		trials++;
+	}
+	if (trials >= WAKE_UP_TRIAL_RETRY) {
+		pr_err("Failed to wake-up the chip\n");
+		return;
 	}
-	wilc->chip_ps_state = WILC_CHIP_WAKEDUP;
 }
 EXPORT_SYMBOL_GPL(chip_wakeup);
 
diff --git a/drivers/net/wireless/microchip/wilc1000/wlan.h b/drivers/net/wireless/microchip/wilc1000/wlan.h
index 771c25fa849b..285e5d9a2b48 100644
--- a/drivers/net/wireless/microchip/wilc1000/wlan.h
+++ b/drivers/net/wireless/microchip/wilc1000/wlan.h
@@ -97,6 +97,8 @@
 #define WILC_SPI_WAKEUP_REG		0x1
 #define WILC_SPI_WAKEUP_BIT		BIT(1)
 
+#define WILC_SPI_CLK_STATUS_REG        0x0f
+#define WILC_SPI_CLK_STATUS_BIT        BIT(2)
 #define WILC_SPI_HOST_TO_FW_REG		0x0b
 #define WILC_SPI_HOST_TO_FW_BIT		BIT(0)
 
diff --git a/drivers/net/wireless/microchip/wilc1000/wlan_if.h b/drivers/net/wireless/microchip/wilc1000/wlan_if.h
index 31c68643731d..6eb7eb4ac294 100644
--- a/drivers/net/wireless/microchip/wilc1000/wlan_if.h
+++ b/drivers/net/wireless/microchip/wilc1000/wlan_if.h
@@ -48,12 +48,6 @@ enum {
 	WILC_FW_MAX_PSPOLL_PS = 4
 };
 
-enum chip_ps_states {
-	WILC_CHIP_WAKEDUP = 0,
-	WILC_CHIP_SLEEPING_AUTO = 1,
-	WILC_CHIP_SLEEPING_MANUAL = 2
-};
-
 enum bus_acquire {
 	WILC_BUS_ACQUIRE_ONLY = 0,
 	WILC_BUS_ACQUIRE_AND_WAKEUP = 1,
-- 
2.25.1

  parent reply	other threads:[~2021-09-16 16:51 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-09-16 16:49 [PATCH v2 00/11] wilc1000: add chip wakeup support and few fixes Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 01/11] wilc1000: move 'deinit_lock' lock init/destroy inside module probe Ajay.Kathat
2021-09-21 15:08   ` Kalle Valo
2021-09-16 16:49 ` [PATCH v2 03/11] wilc1000: add new WID to pass wake_enable information to firmware Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 02/11] wilc1000: fix possible memory leak in cfg_scan_result() Ajay.Kathat
2021-09-16 16:49 ` Ajay.Kathat [this message]
2021-09-16 16:49 ` [PATCH v2 05/11] wilc1000: add reset/terminate/repeat command support for SPI bus Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 06/11] wilc1000: handle read failure issue for clockless registers Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 07/11] wilc1000: ignore clockless registers status response for SPI Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 08/11] wilc1000: invoke chip reset register before firmware download Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 09/11] wilc1000: add 'initialized' flag check before adding an element to TX queue Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 10/11] wilc1000: use correct write command sequence in wilc_spi_sync_ext() Ajay.Kathat
2021-09-16 16:49 ` [PATCH v2 11/11] wilc1000: increase config packets response wait timeout limit Ajay.Kathat

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210916164902.74629-5-ajay.kathat@microchip.com \
    --to=ajay.kathat@microchip.com \
    --cc=Claudiu.Beznea@microchip.com \
    --cc=linux-wireless@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.