All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1
@ 2021-09-20  8:40 Vyacheslav Bocharov
  2021-09-20  8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
                   ` (3 more replies)
  0 siblings, 4 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20  8:40 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic

Add support for new home automation devices manufactured by JetHome.
Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console

Changes from v2:
- fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c
- add missing files to board/amlogic/jethub-j80/MAINTAINERS
- fix unexpected unindent in doc files

Changes from v1:
- fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3)
- add lore URLs to description (patch 2/3)

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>

Vyacheslav Bocharov (3):
  ARM: amlogic: add JetHub common config header
  ARM: amlogic: add JetHub D1/H1 device support
  ARM: amlogic: add JetHub D1/H1 docs

 arch/arm/dts/Makefile                         |   2 +
 .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
 board/amlogic/jethub-j80/MAINTAINERS          |   9 +
 board/amlogic/jethub-j80/Makefile             |   6 +
 board/amlogic/jethub-j80/jethub-j80.c         |  68 ++++
 configs/jethub_j100_defconfig                 |  55 +++
 configs/jethub_j80_defconfig                  |  63 +++
 doc/board/amlogic/index.rst                   | 128 ++++---
 doc/board/amlogic/jethub-j100.rst             | 108 ++++++
 doc/board/amlogic/jethub-j80.rst              |  97 +++++
 include/configs/jethub.h                      |  40 ++
 12 files changed, 1115 insertions(+), 63 deletions(-)
 create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
 create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
 create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
 create mode 100644 board/amlogic/jethub-j80/Makefile
 create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
 create mode 100644 configs/jethub_j100_defconfig
 create mode 100644 configs/jethub_j80_defconfig
 create mode 100644 doc/board/amlogic/jethub-j100.rst
 create mode 100644 doc/board/amlogic/jethub-j80.rst
 create mode 100644 include/configs/jethub.h

-- 
2.30.2


^ permalink raw reply	[flat|nested] 6+ messages in thread
* [PATCH v3 1/3] ARM: amlogic: add JetHub common config header
  2021-09-20  8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
@ 2021-09-20  8:40 ` Vyacheslav Bocharov
  2021-09-20 12:30   ` Neil Armstrong
  2021-09-20  8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
                   ` (2 subsequent siblings)
  3 siblings, 1 reply; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20  8:40 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic

JetHub devices uses its own boot sequence with "rescue" button

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
---
 include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)
 create mode 100644 include/configs/jethub.h

diff --git a/include/configs/jethub.h b/include/configs/jethub.h
new file mode 100644
index 0000000000..35f85095ac
--- /dev/null
+++ b/include/configs/jethub.h
@@ -0,0 +1,40 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Configuration for JetHome devices
+ * Copyright (C) 2021 Vyacheslav Bocharov
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+#ifndef __JETHUB_CONFIG_H
+#define __JETHUB_CONFIG_H
+
+#if defined(CONFIG_MESON_AXG)
+#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
+	"bootcmd_rescue=" \
+		"if gpio input 10; then " \
+		"run bootcmd_usb0;" \
+		"fi;\0"
+#else
+#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
+	"bootcmd_rescue=" \
+		"if test \"${userbutton}\" = \"true\"; then " \
+		"run bootcmd_mmc0; " \
+		"fi;\0"
+#endif
+
+#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \
+	"rescue "
+
+#ifndef BOOT_TARGET_DEVICES
+#define BOOT_TARGET_DEVICES(func) \
+	func(RESCUE, rescue, na) \
+	func(MMC, mmc, 1) \
+	func(MMC, mmc, 0) \
+	BOOT_TARGET_DEVICES_USB(func) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+#endif
+
+#include <configs/meson64.h>
+
+#endif /* __JETHUB_CONFIG_H */
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 6+ messages in thread
* [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support
  2021-09-20  8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
  2021-09-20  8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
@ 2021-09-20  8:40 ` Vyacheslav Bocharov
  2021-09-20  8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
  2021-09-21  7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
  3 siblings, 0 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20  8:40 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic

Add support for new home automation devices.

JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE

JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console

Patches from:
- JetHub H1
  https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in
  https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
  https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in
  https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
 arch/arm/dts/Makefile                         |   2 +
 .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
 .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
 board/amlogic/jethub-j80/MAINTAINERS          |   9 +
 board/amlogic/jethub-j80/Makefile             |   6 +
 board/amlogic/jethub-j80/jethub-j80.c         |  68 ++++
 configs/jethub_j100_defconfig                 |  55 +++
 configs/jethub_j80_defconfig                  |  63 +++
 8 files changed, 805 insertions(+)
 create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
 create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
 create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
 create mode 100644 board/amlogic/jethub-j80/Makefile
 create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
 create mode 100644 configs/jethub_j100_defconfig
 create mode 100644 configs/jethub_j80_defconfig

diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index f0160d2dc0..d1893a9812 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -169,10 +169,12 @@ dtb-$(CONFIG_ARCH_MESON) += \
 	meson-gxl-s905x-libretech-cc-v2.dtb \
 	meson-gxl-s905x-khadas-vim.dtb \
 	meson-gxl-s905d-libretech-pc.dtb \
+	meson-gxl-s905w-jethome-jethub-j80.dtb \
 	meson-gxm-khadas-vim2.dtb \
 	meson-gxm-s912-libretech-pc.dtb \
 	meson-gxm-wetek-core2.dtb \
 	meson-axg-s400.dtb \
+	meson-axg-jethome-jethub-j100.dtb \
 	meson-g12a-u200.dtb \
 	meson-g12a-sei510.dtb \
 	meson-g12b-gtking.dtb \
diff --git a/arch/arm/dts/meson-axg-jethome-jethub-j100.dts b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts
new file mode 100644
index 0000000000..5783732dc6
--- /dev/null
+++ b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts
@@ -0,0 +1,361 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub J100";
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* 1024MB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		cpu_cooling_maps: cooling-maps {
+			map0 {
+				trip = <&cpu_passive>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+
+			map1 {
+				trip = <&cpu_hot>;
+				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+		#gpio-cells = <1>;
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
diff --git a/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
new file mode 100644
index 0000000000..6eafb90869
--- /dev/null
+++ b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2020 JetHome
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl";
+	model = "JetHome JetHub J80";
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x1000000>;
+		};
+	};
+
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial1 = &uart_A;    /* Bluetooth */
+		serial2 = &uart_AO_B; /* Wireless module 1 */
+		serial3 = &uart_C;    /* Wireless module 2 */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+};
+
+&efuse {
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@C {
+		reg = <0xc 0x6>;
+	};
+};
+
+&sn {
+	reg = <0x32 0x20>;
+};
+
+&eth_mac {
+	reg = <0x0 0x6>;
+};
+
+&bid {
+	reg = <0x12 0x20>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&clkc CLKID_FCLK_DIV4>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao18>;
+};
+
+/* Wireless SDIO Module */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* Console UART */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* S905W only has access to its internal PHY */
+&ethmac {
+	status = "okay";
+	phy-mode = "rmii";
+	phy-handle = <&internal_phy>;
+};
+
+&internal_phy {
+	status = "okay";
+	pinctrl-0 = <&eth_link_led_pins>, <&eth_act_led_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&uart_C {
+	status = "okay";
+	pinctrl-0 = <&uart_c_pins>;
+	pinctrl-names = "default";
+};
+
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+&i2c_B {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c_b_pins>;
+
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
diff --git a/board/amlogic/jethub-j80/MAINTAINERS b/board/amlogic/jethub-j80/MAINTAINERS
new file mode 100644
index 0000000000..459e9f89da
--- /dev/null
+++ b/board/amlogic/jethub-j80/MAINTAINERS
@@ -0,0 +1,9 @@
+JetHome JetHub
+M:	Vyacheslav Bocharov <adeep@lexina.in>
+S:	Maintained
+L:	u-boot-amlogic@groups.io
+F:	board/amlogic/jethub-j80/
+F:	configs/jethub_j80_defconfig
+F:	configs/jethub_j100_defconfig
+F:	doc/board/amlogic/jethub-j80.rst
+F:	doc/board/amlogic/jethub-j100.rst
diff --git a/board/amlogic/jethub-j80/Makefile b/board/amlogic/jethub-j80/Makefile
new file mode 100644
index 0000000000..a727a4b222
--- /dev/null
+++ b/board/amlogic/jethub-j80/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2021 Vyacheslav Bocharov
+# Author: Vyacheslav Bocharov <adeep@lexina.in>
+
+obj-y	:= jethub-j80.o
diff --git a/board/amlogic/jethub-j80/jethub-j80.c b/board/amlogic/jethub-j80/jethub-j80.c
new file mode 100644
index 0000000000..ae402303aa
--- /dev/null
+++ b/board/amlogic/jethub-j80/jethub-j80.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2021 Vyacheslav Bocharov
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <adc.h>
+#include <env.h>
+#include <init.h>
+#include <net.h>
+#include <asm/io.h>
+#include <asm/arch/gx.h>
+#include <asm/arch/sm.h>
+#include <asm/arch/eth.h>
+#include <asm/arch/mem.h>
+
+#define EFUSE_SN_OFFSET		50
+#define EFUSE_SN_SIZE		32
+#define EFUSE_MAC_OFFSET	0
+#define EFUSE_MAC_SIZE		6
+#define EFUSE_USID_OFFSET	18
+#define EFUSE_USID_SIZE		32
+
+int misc_init_r(void)
+{
+	u8 mac_addr[EFUSE_MAC_SIZE];
+	char serial[EFUSE_SN_SIZE];
+	char usid[EFUSE_USID_SIZE];
+	ssize_t len;
+	unsigned int adcval;
+	int ret;
+	char value[16];
+
+	if (!eth_env_get_enetaddr("ethaddr", mac_addr)) {
+		len = meson_sm_read_efuse(EFUSE_MAC_OFFSET,
+					  mac_addr, EFUSE_MAC_SIZE);
+		if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr))
+			eth_env_set_enetaddr("ethaddr", mac_addr);
+		else
+			meson_generate_serial_ethaddr();
+	}
+
+	if (!env_get("serial")) {
+		len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial,
+					  EFUSE_SN_SIZE);
+		if (len == EFUSE_SN_SIZE)
+			env_set("serial", serial);
+	}
+
+	if (!env_get("usid")) {
+		len = meson_sm_read_efuse(EFUSE_USID_OFFSET, usid,
+					  EFUSE_USID_SIZE);
+		if (len == EFUSE_USID_SIZE)
+			env_set("usid", usid);
+	}
+
+	ret = adc_channel_single_shot("adc@8680", 0, &adcval);
+	if (adcval < 3000)
+		env_set("userbutton", "true");
+	else
+		env_set("userbutton", "false");
+
+	return 0;
+}
diff --git a/configs/jethub_j100_defconfig b/configs/jethub_j100_defconfig
new file mode 100644
index 0000000000..290ce4db85
--- /dev/null
+++ b/configs/jethub_j100_defconfig
@@ -0,0 +1,55 @@
+CONFIG_ARM=y
+CONFIG_SYS_CONFIG_NAME="jethub"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-axg-jethome-jethub-j100"
+CONFIG_MESON_AXG=y
+CONFIG_DEBUG_UART_BASE=0xff803000
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" jethubj100"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_GPIO=y
+CONFIG_RANDOM_UUID=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MTD_UBI=y
+CONFIG_PHY_REALTEK=y
+CONFIG_DM_ETH=y
+CONFIG_ETH_DESIGNWARE_MESON8B=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_AXG=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_GXL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/jethub_j80_defconfig b/configs/jethub_j80_defconfig
new file mode 100644
index 0000000000..7db05af3b0
--- /dev/null
+++ b/configs/jethub_j80_defconfig
@@ -0,0 +1,63 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="jethub-j80"
+CONFIG_SYS_CONFIG_NAME="jethub"
+CONFIG_ARCH_MESON=y
+CONFIG_SYS_TEXT_BASE=0x01000000
+CONFIG_NR_DRAM_BANKS=1
+CONFIG_ENV_SIZE=0x2000
+CONFIG_DM_GPIO=y
+CONFIG_DEFAULT_DEVICE_TREE="meson-gxl-s905w-jethome-jethub-j80"
+CONFIG_MESON_GXL=y
+CONFIG_DEBUG_UART_BASE=0xc81004c0
+CONFIG_DEBUG_UART_CLOCK=24000000
+CONFIG_IDENT_STRING=" jethubj80"
+CONFIG_DEBUG_UART=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_CONSOLE_MUX=y
+# CONFIG_DISPLAY_CPUINFO is not set
+CONFIG_MISC_INIT_R=y
+# CONFIG_CMD_BDI is not set
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_ADC=y
+CONFIG_CMD_GPIO=y
+CONFIG_RANDOM_UUID=y
+# CONFIG_CMD_LOADS is not set
+CONFIG_CMD_MMC=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_USB_MASS_STORAGE=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_PARTITION_TYPE_GUID=y
+CONFIG_OF_CONTROL=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_SARADC_MESON=y
+CONFIG_MMC_MESON_GX=y
+CONFIG_MTD_UBI=y
+CONFIG_PHY_MESON_GXL=y
+CONFIG_DM_ETH=y
+CONFIG_DM_MDIO=y
+CONFIG_DM_MDIO_MUX=y
+CONFIG_ETH_DESIGNWARE_MESON8B=y
+CONFIG_MDIO_MUX_MMIOREG=y
+CONFIG_MESON_GXL_USB_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_MESON_GXL=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_RESET=y
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_DEBUG_UART_SKIP_INIT=y
+CONFIG_MESON_SERIAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_DWC2=y
+CONFIG_USB_DWC3=y
+# CONFIG_USB_DWC3_GADGET is not set
+CONFIG_USB_DWC3_MESON_GXL=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e
+CONFIG_USB_GADGET_PRODUCT_NUM=0xfada
+CONFIG_USB_GADGET_DWC2_OTG=y
+CONFIG_USB_GADGET_DOWNLOAD=y
+CONFIG_OF_LIBFDT_OVERLAY=y
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 6+ messages in thread
* [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs
  2021-09-20  8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
  2021-09-20  8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
  2021-09-20  8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
@ 2021-09-20  8:40 ` Vyacheslav Bocharov
  2021-09-21  7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
  3 siblings, 0 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20  8:40 UTC (permalink / raw)
  To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic

Fix doc/board/amlogic/index.rst:
- Add S905W to S905X column.
- Add JetHub devices to the corresponding columns.
- Fix tabs to spaces for table alignment

Add doc/board/amlogic files:
- jethub-j100.rst
- jethub-j80.rst

Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
---
 doc/board/amlogic/index.rst       | 128 +++++++++++++++---------------
 doc/board/amlogic/jethub-j100.rst | 108 +++++++++++++++++++++++++
 doc/board/amlogic/jethub-j80.rst  |  97 ++++++++++++++++++++++
 3 files changed, 270 insertions(+), 63 deletions(-)
 create mode 100644 doc/board/amlogic/jethub-j100.rst
 create mode 100644 doc/board/amlogic/jethub-j80.rst

diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst
index 2913ab281a..c18f1b7e71 100644
--- a/doc/board/amlogic/index.rst
+++ b/doc/board/amlogic/index.rst
@@ -10,69 +10,69 @@ An up-do-date matrix is also available on: http://linux-meson.com
 
 This matrix concerns the actual source code version.
 
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-|                            	| S905      | S905X           | S912         | A113X      | S905X2     | S922X       | S905X3       |
-|        			|	    | S805X   	      | S905D        |	          | S905D2     | A311D       | S905D3       |
-|        			|	    |		      |	             |            | S905Y2     |	     |              |
-+===============================+===========+=================+==============+============+============+=============+==============+
-| Boards                       	| Odroid-C2 | P212            | Khadas VIM2  | S400       | U200       | Odroid-N2   | SEI610       |
-|        			| Nanopi-K2 | Khadas-VIM      | Libretech-PC |	          | SEI510     | Khadas-VIM3 | Khadas-VIM3L |
-|        			| P200	    | LibreTech-CC v1 |	WeTek Core2  |	          |            | GT-King/Pro | Odroid-C4    |
-|        			| P201	    | LibreTech-AC v2 |	             |	          |            | GSKing-X    | Odroid-HC4   |
-|                               |           |                 |              |            |            |             | BananaPi-M5  |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| UART                       	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Pinctrl/GPIO               	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Clock Control              	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| PWM                        	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Reset Control              	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Infrared Decoder           	| No        | No              | No           | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Ethernet                   	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Multi-core                 	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Fuse access                	| **Yes**   | **Yes**         |**Yes**       |**Yes**     |**Yes**     |**Yes**      | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SPI (FC)                  	| **Yes**   | **Yes**         | **Yes**      | **Yes**    |**Yes**     | **Yes**     | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SPI (CC)                   	| No        | No              | No           | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| I2C                       	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| USB                       	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| USB OTG                  	| No        | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| eMMC                      	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SDCard                    	| **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| NAND                      	| No        | No              | No           | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| ADC                       	| **Yes**   | **Yes**         | **Yes**      | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| CVBS Output                	| **Yes**   | **Yes**         | **Yes**      | *N/A*      | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| HDMI Output                	| **Yes**   | **Yes**         | **Yes**      | *N/A*      | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| CEC                        	| No        | No              | No           | *N/A*      | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| Thermal Sensor             	| No        | No              | No           | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| LCD/LVDS Output            	| No        | *N/A*           | No           | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| MIPI DSI Output            	| *N/A*     | *N/A*           | *N/A*        | No         | No         | No          | No           |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| SoC (version) information     | **Yes**   | **Yes**         | **Yes**      | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
-| PCIe (+NVMe)                  | *N/A*     | *N/A*           | *N/A*        | **Yes**    | **Yes**    | **Yes**     | **Yes**      |
-+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+|                               | S905      | S905X           | S912         | A113X       | S905X2     | S922X       | S905X3       |
+|                               |           | S805X           | S905D        |             | S905D2     | A311D       | S905D3       |
+|                               |           | S905W           |              |             | S905Y2     |             |              |
++===============================+===========+=================+==============+=============+============+=============+==============+
+| Boards                        | Odroid-C2 | P212            | Khadas VIM2  | S400        | U200       | Odroid-N2   | SEI610       |
+|                               | Nanopi-K2 | Khadas-VIM      | Libretech-PC | JetHub J100 | SEI510     | Khadas-VIM3 | Khadas-VIM3L |
+|                               | P200      | LibreTech-CC v1 | WeTek Core2  |             |            | GT-King/Pro | Odroid-C4    |
+|                               | P201      | LibreTech-AC v2 |              |             |            | GSKing-X    | Odroid-HC4   |
+|                               |           | JetHub J80      |              |             |            |             | BananaPi-M5  |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| UART                          | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Pinctrl/GPIO                  | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Clock Control                 | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| PWM                           | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Reset Control                 | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Infrared Decoder              | No        | No              | No           | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Ethernet                      | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Multi-core                    | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Fuse access                   | **Yes**   | **Yes**         |**Yes**       |**Yes**      |**Yes**     |**Yes**      | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SPI (FC)                      | **Yes**   | **Yes**         | **Yes**      | **Yes**     |**Yes**     | **Yes**     | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SPI (CC)                      | No        | No              | No           | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| I2C                           | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| USB                           | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| USB OTG                       | No        | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| eMMC                          | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SDCard                        | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| NAND                          | No        | No              | No           | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| ADC                           | **Yes**   | **Yes**         | **Yes**      | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| CVBS Output                   | **Yes**   | **Yes**         | **Yes**      | *N/A*       | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| HDMI Output                   | **Yes**   | **Yes**         | **Yes**      | *N/A*       | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| CEC                           | No        | No              | No           | *N/A*       | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| Thermal Sensor                | No        | No              | No           | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| LCD/LVDS Output               | No        | *N/A*           | No           | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| MIPI DSI Output               | *N/A*     | *N/A*           | *N/A*        | No          | No         | No          | No           |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| SoC (version) information     | **Yes**   | **Yes**         | **Yes**      | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
+| PCIe (+NVMe)                  | *N/A*     | *N/A*           | *N/A*        | **Yes**     | **Yes**    | **Yes**     | **Yes**      |
++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+
 
 Board Documentation
 -------------------
@@ -82,6 +82,8 @@ Board Documentation
 
    beelink-gtking
    beelink-gtkingpro
+   jethub-j100
+   jethub-j80
    khadas-vim2
    khadas-vim3l
    khadas-vim3
diff --git a/doc/board/amlogic/jethub-j100.rst b/doc/board/amlogic/jethub-j100.rst
new file mode 100644
index 0000000000..58602787d3
--- /dev/null
+++ b/doc/board/amlogic/jethub-j100.rst
@@ -0,0 +1,108 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for JetHub J100
+=======================
+
+JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
+controller manufactured by JetHome with the following specifications:
+
+ - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
+ - no video out
+ - 512Mb/1GB DDR3
+ - 8/16GB eMMC flash
+ - 1 x USB 2.0
+ - 1 x 10/100Mbps ethernet
+ - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE
+   802.11a/b/g/n/ac, Bluetooth 4.2.
+ - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output
+   power and Zigbee 3.0 support.
+ - 2 x gpio LEDS
+ - GPIO user Button
+ - 1 x 1-Wire
+ - 2 x RS-485
+ - 4 x dry contact digital GPIO inputs
+ - 3 x relay GPIO outputs
+ - DC source with a voltage of 9 to 56 V / Passive POE
+ - DIN Rail Mounting case
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+    $ export CROSS_COMPILE=aarch64-none-elf-
+    $ make jethub_j100_defconfig
+    $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain binaries
+from the git tree published by the board vendor:
+
+.. code-block:: bash
+
+    $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot
+    $ cd jethub-u-boot
+    $ export FIPDIR=$PWD
+
+Go back to mainline U-boot source tree then :
+
+.. code-block:: bash
+
+    $ mkdir fip
+
+    $ cp $FIPDIR/j100/bl2.bin fip/
+    $ cp $FIPDIR/j100/acs.bin fip/
+    $ cp $FIPDIR/j100/bl21.bin fip/
+    $ cp $FIPDIR/j100/bl30.bin fip/
+    $ cp $FIPDIR/j100/bl301.bin fip/
+    $ cp $FIPDIR/j100/bl31.img fip/
+    $ cp u-boot.bin fip/bl33.bin
+
+    $ $FIPDIR/blx_fix.sh \
+        fip/bl30.bin \
+        fip/zero_tmp \
+        fip/bl30_zero.bin \
+        fip/bl301.bin \
+        fip/bl301_zero.bin \
+        fip/bl30_new.bin \
+        bl30
+
+    $ $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+    $ $FIPDIR/blx_fix.sh \
+        fip/bl2_acs.bin \
+        fip/zero_tmp \
+        fip/bl2_zero.bin \
+        fip/bl21.bin \
+        fip/bl21_zero.bin \
+        fip/bl2_new.bin \
+        bl2
+
+    $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl30_new.bin \
+                                        --output fip/bl30_new.bin.enc \
+                                        --level v3 --type bl30
+    $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl31.img \
+                                        --output fip/bl31.img.enc \
+                                        --level v3 --type bl31
+    $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl33.bin --compress lz4 \
+                                        --output fip/bl33.bin.enc \
+                                        --level v3 --type bl33
+    $ $FIPDIR/j100/aml_encrypt_axg --bl2sig --input fip/bl2_new.bin \
+                                        --output fip/bl2.n.bin.sig
+    $ $FIPDIR/j100/aml_encrypt_axg --bootmk \
+                --output fip/u-boot.bin \
+                --bl2 fip/bl2.n.bin.sig \
+                --bl30 fip/bl30_new.bin.enc \
+                --bl31 fip/bl31.img.enc \
+                --bl33 fip/bl33.bin.enc --level v3
+
+and then write the image to eMMC with:
+
+.. code-block:: bash
+
+    $ DEV=/dev/your_emmc_device
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
diff --git a/doc/board/amlogic/jethub-j80.rst b/doc/board/amlogic/jethub-j80.rst
new file mode 100644
index 0000000000..6b7bdc78b1
--- /dev/null
+++ b/doc/board/amlogic/jethub-j80.rst
@@ -0,0 +1,97 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+U-Boot for JetHub J80
+======================
+
+JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
+controller manufactured by JetHome with the following specifications:
+
+ - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
+ - No video out
+ - 1GB DDR3
+ - 8/16GB eMMC flash
+ - 2 x USB 2.0
+ - 1 x 10/100Mbps ethernet
+ - SDIO WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
+ - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output
+   power and Zigbee 3.0 support.
+ - MicroSD 2.x/3.x/4.x DS/HS cards.
+ - 1 x gpio LED
+ - ADC user Button
+ - DC source 5V microUSB
+ - Square plastic case
+
+U-Boot compilation
+------------------
+
+.. code-block:: bash
+
+    $ export CROSS_COMPILE=aarch64-none-elf-
+    $ make jethub_j80_defconfig
+    $ make
+
+Image creation
+--------------
+
+Amlogic doesn't provide sources for the firmware and for tools needed
+to create the bootloader image, so it is necessary to obtain binaries
+from the git tree published by the board vendor:
+
+.. code-block:: bash
+
+    $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot
+    $ cd jethub-u-boot
+    $ export FIPDIR=$PWD
+
+Go back to mainline U-Boot source tree then :
+
+.. code-block:: bash
+
+    $ mkdir fip
+
+    $ cp $FIPDIR/j80/bl2.bin fip/
+    $ cp $FIPDIR/j80/acs.bin fip/
+    $ cp $FIPDIR/j80/bl21.bin fip/
+    $ cp $FIPDIR/j80/bl30.bin fip/
+    $ cp $FIPDIR/j80/bl301.bin fip/
+    $ cp $FIPDIR/j80/bl31.img fip/
+    $ cp u-boot.bin fip/bl33.bin
+
+    $ $FIPDIR/blx_fix.sh \
+        fip/bl30.bin \
+        fip/zero_tmp \
+        fip/bl30_zero.bin \
+        fip/bl301.bin \
+        fip/bl301_zero.bin \
+        fip/bl30_new.bin \
+        bl30
+
+    $ python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0
+
+    $ $FIPDIR/blx_fix.sh \
+        fip/bl2_acs.bin \
+        fip/zero_tmp \
+        fip/bl2_zero.bin \
+        fip/bl21.bin \
+        fip/bl21_zero.bin \
+        fip/bl2_new.bin \
+        bl2
+
+    $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin
+    $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl31.img
+    $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl33.bin --compress lz4
+    $ $FIPDIR/j80/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig
+    $ $FIPDIR/j80/aml_encrypt_gxl --bootmk \
+                --output fip/u-boot.bin \
+                --bl2 fip/bl2.n.bin.sig \
+                --bl30 fip/bl30_new.bin.enc \
+                --bl31 fip/bl31.img.enc \
+                --bl33 fip/bl33.bin.enc
+
+and then write the image to SD/eMMC with:
+
+.. code-block:: bash
+
+    $ DEV=/dev/your_sd_device
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1
+    $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444
-- 
2.30.2


^ permalink raw reply related	[flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/3] ARM: amlogic: add JetHub common config header
  2021-09-20  8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
@ 2021-09-20 12:30   ` Neil Armstrong
  0 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2021-09-20 12:30 UTC (permalink / raw)
  To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic

On 20/09/2021 10:40, Vyacheslav Bocharov wrote:
> JetHub devices uses its own boot sequence with "rescue" button
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> ---
>  include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 40 insertions(+)
>  create mode 100644 include/configs/jethub.h
> 
> diff --git a/include/configs/jethub.h b/include/configs/jethub.h
> new file mode 100644
> index 0000000000..35f85095ac
> --- /dev/null
> +++ b/include/configs/jethub.h
> @@ -0,0 +1,40 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Configuration for JetHome devices
> + * Copyright (C) 2021 Vyacheslav Bocharov
> + * Author: Vyacheslav Bocharov <adeep@lexina.in>
> + */
> +
> +#ifndef __JETHUB_CONFIG_H
> +#define __JETHUB_CONFIG_H
> +
> +#if defined(CONFIG_MESON_AXG)
> +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
> +	"bootcmd_rescue=" \
> +		"if gpio input 10; then " \
> +		"run bootcmd_usb0;" \
> +		"fi;\0"
> +#else
> +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \
> +	"bootcmd_rescue=" \
> +		"if test \"${userbutton}\" = \"true\"; then " \
> +		"run bootcmd_mmc0; " \
> +		"fi;\0"
> +#endif
> +
> +#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \
> +	"rescue "
> +
> +#ifndef BOOT_TARGET_DEVICES
> +#define BOOT_TARGET_DEVICES(func) \
> +	func(RESCUE, rescue, na) \
> +	func(MMC, mmc, 1) \
> +	func(MMC, mmc, 0) \
> +	BOOT_TARGET_DEVICES_USB(func) \
> +	func(PXE, pxe, na) \
> +	func(DHCP, dhcp, na)
> +#endif
> +
> +#include <configs/meson64.h>
> +
> +#endif /* __JETHUB_CONFIG_H */
> 

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>

^ permalink raw reply	[flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1
  2021-09-20  8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
                   ` (2 preceding siblings ...)
  2021-09-20  8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
@ 2021-09-21  7:27 ` Neil Armstrong
  3 siblings, 0 replies; 6+ messages in thread
From: Neil Armstrong @ 2021-09-21  7:27 UTC (permalink / raw)
  To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic

On 20/09/2021 10:40, Vyacheslav Bocharov wrote:
> Add support for new home automation devices manufactured by JetHome.
> Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong
> 
> JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
> - DIN Rail Mounting case
> - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 512Mb/1GB DDR3
> - 8/16GB eMMC flash
> - 1 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
> - 2 x gpio LEDS
> - GPIO user Button
> - 1 x 1-Wire
> - 2 x RS-485
> - 4 x dry contact digital GPIO inputs
> - 3 x relay GPIO outputs
> - DC source with a voltage of 9 to 56 V / Passive POE
> 
> JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
> - Square plastic case
> - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
> - no video out
> - 1GB DDR3
> - 8/16GB eMMC flash
> - 2 x USB 2.0
> - 1 x 10/100Mbps ethernet
> - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
> - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
> - MicroSD 2.x/3.x/4.x DS/HS cards.
> - 1 x gpio LED
> - ADC user Button
> - DC source 5V microUSB with serial console
> 
> Changes from v2:
> - fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c
> - add missing files to board/amlogic/jethub-j80/MAINTAINERS
> - fix unexpected unindent in doc files
> 
> Changes from v1:
> - fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3)
> - add lore URLs to description (patch 2/3)
> 
> Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
> 
> Vyacheslav Bocharov (3):
>   ARM: amlogic: add JetHub common config header
>   ARM: amlogic: add JetHub D1/H1 device support
>   ARM: amlogic: add JetHub D1/H1 docs
> 
>  arch/arm/dts/Makefile                         |   2 +
>  .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
>  .../meson-gxl-s905w-jethome-jethub-j80.dts    | 241 ++++++++++++
>  board/amlogic/jethub-j80/MAINTAINERS          |   9 +
>  board/amlogic/jethub-j80/Makefile             |   6 +
>  board/amlogic/jethub-j80/jethub-j80.c         |  68 ++++
>  configs/jethub_j100_defconfig                 |  55 +++
>  configs/jethub_j80_defconfig                  |  63 +++
>  doc/board/amlogic/index.rst                   | 128 ++++---
>  doc/board/amlogic/jethub-j100.rst             | 108 ++++++
>  doc/board/amlogic/jethub-j80.rst              |  97 +++++
>  include/configs/jethub.h                      |  40 ++
>  12 files changed, 1115 insertions(+), 63 deletions(-)
>  create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
>  create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
>  create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
>  create mode 100644 board/amlogic/jethub-j80/Makefile
>  create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
>  create mode 100644 configs/jethub_j100_defconfig
>  create mode 100644 configs/jethub_j80_defconfig
>  create mode 100644 doc/board/amlogic/jethub-j100.rst
>  create mode 100644 doc/board/amlogic/jethub-j80.rst
>  create mode 100644 include/configs/jethub.h
> 


Applied to u-boot-amlogic-next

Neil

^ permalink raw reply	[flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-09-21  7:28 UTC | newest]

Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-20  8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov
2021-09-20  8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
2021-09-20 12:30   ` Neil Armstrong
2021-09-20  8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov
2021-09-20  8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov
2021-09-21  7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.