* [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1
@ 2021-09-20 8:40 Vyacheslav Bocharov
2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw)
To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic
Add support for new home automation devices manufactured by JetHome.
Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Changes from v2:
- fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c
- add missing files to board/amlogic/jethub-j80/MAINTAINERS
- fix unexpected unindent in doc files
Changes from v1:
- fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3)
- add lore URLs to description (patch 2/3)
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Vyacheslav Bocharov (3):
ARM: amlogic: add JetHub common config header
ARM: amlogic: add JetHub D1/H1 device support
ARM: amlogic: add JetHub D1/H1 docs
arch/arm/dts/Makefile | 2 +
.../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++
.../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++
board/amlogic/jethub-j80/MAINTAINERS | 9 +
board/amlogic/jethub-j80/Makefile | 6 +
board/amlogic/jethub-j80/jethub-j80.c | 68 ++++
configs/jethub_j100_defconfig | 55 +++
configs/jethub_j80_defconfig | 63 +++
doc/board/amlogic/index.rst | 128 ++++---
doc/board/amlogic/jethub-j100.rst | 108 ++++++
doc/board/amlogic/jethub-j80.rst | 97 +++++
include/configs/jethub.h | 40 ++
12 files changed, 1115 insertions(+), 63 deletions(-)
create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts
create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts
create mode 100644 board/amlogic/jethub-j80/MAINTAINERS
create mode 100644 board/amlogic/jethub-j80/Makefile
create mode 100644 board/amlogic/jethub-j80/jethub-j80.c
create mode 100644 configs/jethub_j100_defconfig
create mode 100644 configs/jethub_j80_defconfig
create mode 100644 doc/board/amlogic/jethub-j100.rst
create mode 100644 doc/board/amlogic/jethub-j80.rst
create mode 100644 include/configs/jethub.h
--
2.30.2
^ permalink raw reply [flat|nested] 6+ messages in thread* [PATCH v3 1/3] ARM: amlogic: add JetHub common config header 2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov @ 2021-09-20 8:40 ` Vyacheslav Bocharov 2021-09-20 12:30 ` Neil Armstrong 2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov ` (2 subsequent siblings) 3 siblings, 1 reply; 6+ messages in thread From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw) To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic JetHub devices uses its own boot sequence with "rescue" button Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> --- include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) create mode 100644 include/configs/jethub.h diff --git a/include/configs/jethub.h b/include/configs/jethub.h new file mode 100644 index 0000000000..35f85095ac --- /dev/null +++ b/include/configs/jethub.h @@ -0,0 +1,40 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * Configuration for JetHome devices + * Copyright (C) 2021 Vyacheslav Bocharov + * Author: Vyacheslav Bocharov <adeep@lexina.in> + */ + +#ifndef __JETHUB_CONFIG_H +#define __JETHUB_CONFIG_H + +#if defined(CONFIG_MESON_AXG) +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \ + "bootcmd_rescue=" \ + "if gpio input 10; then " \ + "run bootcmd_usb0;" \ + "fi;\0" +#else +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \ + "bootcmd_rescue=" \ + "if test \"${userbutton}\" = \"true\"; then " \ + "run bootcmd_mmc0; " \ + "fi;\0" +#endif + +#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \ + "rescue " + +#ifndef BOOT_TARGET_DEVICES +#define BOOT_TARGET_DEVICES(func) \ + func(RESCUE, rescue, na) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 0) \ + BOOT_TARGET_DEVICES_USB(func) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) +#endif + +#include <configs/meson64.h> + +#endif /* __JETHUB_CONFIG_H */ -- 2.30.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 1/3] ARM: amlogic: add JetHub common config header 2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov @ 2021-09-20 12:30 ` Neil Armstrong 0 siblings, 0 replies; 6+ messages in thread From: Neil Armstrong @ 2021-09-20 12:30 UTC (permalink / raw) To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic On 20/09/2021 10:40, Vyacheslav Bocharov wrote: > JetHub devices uses its own boot sequence with "rescue" button > > Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> > --- > include/configs/jethub.h | 40 ++++++++++++++++++++++++++++++++++++++++ > 1 file changed, 40 insertions(+) > create mode 100644 include/configs/jethub.h > > diff --git a/include/configs/jethub.h b/include/configs/jethub.h > new file mode 100644 > index 0000000000..35f85095ac > --- /dev/null > +++ b/include/configs/jethub.h > @@ -0,0 +1,40 @@ > +/* SPDX-License-Identifier: GPL-2.0+ */ > +/* > + * Configuration for JetHome devices > + * Copyright (C) 2021 Vyacheslav Bocharov > + * Author: Vyacheslav Bocharov <adeep@lexina.in> > + */ > + > +#ifndef __JETHUB_CONFIG_H > +#define __JETHUB_CONFIG_H > + > +#if defined(CONFIG_MESON_AXG) > +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \ > + "bootcmd_rescue=" \ > + "if gpio input 10; then " \ > + "run bootcmd_usb0;" \ > + "fi;\0" > +#else > +#define BOOTENV_DEV_RESCUE(devtypeu, devtypel, instance) \ > + "bootcmd_rescue=" \ > + "if test \"${userbutton}\" = \"true\"; then " \ > + "run bootcmd_mmc0; " \ > + "fi;\0" > +#endif > + > +#define BOOTENV_DEV_NAME_RESCUE(devtypeu, devtypel, instance) \ > + "rescue " > + > +#ifndef BOOT_TARGET_DEVICES > +#define BOOT_TARGET_DEVICES(func) \ > + func(RESCUE, rescue, na) \ > + func(MMC, mmc, 1) \ > + func(MMC, mmc, 0) \ > + BOOT_TARGET_DEVICES_USB(func) \ > + func(PXE, pxe, na) \ > + func(DHCP, dhcp, na) > +#endif > + > +#include <configs/meson64.h> > + > +#endif /* __JETHUB_CONFIG_H */ > Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support 2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov @ 2021-09-20 8:40 ` Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov 2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong 3 siblings, 0 replies; 6+ messages in thread From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw) To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic Add support for new home automation devices. JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features: - DIN Rail Mounting case - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz - no video out - 512Mb/1GB DDR3 - 8/16GB eMMC flash - 1 x USB 2.0 - 1 x 10/100Mbps ethernet - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2. - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. - 2 x gpio LEDS - GPIO user Button - 1 x 1-Wire - 2 x RS-485 - 4 x dry contact digital GPIO inputs - 3 x relay GPIO outputs - DC source with a voltage of 9 to 56 V / Passive POE JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features: - Square plastic case - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz - no video out - 1GB DDR3 - 8/16GB eMMC flash - 2 x USB 2.0 - 1 x 10/100Mbps ethernet - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0. - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. - MicroSD 2.x/3.x/4.x DS/HS cards. - 1 x gpio LED - ADC user Button - DC source 5V microUSB with serial console Patches from: - JetHub H1 https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in https://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607 - JetHub D1 https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in https://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79 Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> --- arch/arm/dts/Makefile | 2 + .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++ .../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++ board/amlogic/jethub-j80/MAINTAINERS | 9 + board/amlogic/jethub-j80/Makefile | 6 + board/amlogic/jethub-j80/jethub-j80.c | 68 ++++ configs/jethub_j100_defconfig | 55 +++ configs/jethub_j80_defconfig | 63 +++ 8 files changed, 805 insertions(+) create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts create mode 100644 board/amlogic/jethub-j80/MAINTAINERS create mode 100644 board/amlogic/jethub-j80/Makefile create mode 100644 board/amlogic/jethub-j80/jethub-j80.c create mode 100644 configs/jethub_j100_defconfig create mode 100644 configs/jethub_j80_defconfig diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index f0160d2dc0..d1893a9812 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -169,10 +169,12 @@ dtb-$(CONFIG_ARCH_MESON) += \ meson-gxl-s905x-libretech-cc-v2.dtb \ meson-gxl-s905x-khadas-vim.dtb \ meson-gxl-s905d-libretech-pc.dtb \ + meson-gxl-s905w-jethome-jethub-j80.dtb \ meson-gxm-khadas-vim2.dtb \ meson-gxm-s912-libretech-pc.dtb \ meson-gxm-wetek-core2.dtb \ meson-axg-s400.dtb \ + meson-axg-jethome-jethub-j100.dtb \ meson-g12a-u200.dtb \ meson-g12a-sei510.dtb \ meson-g12b-gtking.dtb \ diff --git a/arch/arm/dts/meson-axg-jethome-jethub-j100.dts b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts new file mode 100644 index 0000000000..5783732dc6 --- /dev/null +++ b/arch/arm/dts/meson-axg-jethome-jethub-j100.dts @@ -0,0 +1,361 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in> + * Copyright (c) 2020 JetHome + * Author: Aleksandr Kazantsev <ak@tvip.ru> + * Author: Alexey Shevelkin <ash@tvip.ru> + * Author: Vyacheslav Bocharov <adeep@lexina.in> + */ + +/dts-v1/; + +#include "meson-axg.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg"; + model = "JetHome JetHub J100"; + aliases { + serial0 = &uart_AO; /* Console */ + serial1 = &uart_AO_B; /* External UART (Wireless Module) */ + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + /* 1024MB RAM */ + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + reserved-memory { + linux,cma { + size = <0x0 0x400000>; + }; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "VCC5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vcc_5v>; + regulator-always-on; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + usb_pwr: regulator-usb_pwr { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + regulator-always-on; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */ + }; + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <250>; + polling-delay = <1000>; + thermal-sensors = <&scpi_sensors 0>; + trips { + cpu_passive: cpu-passive { + temperature = <70000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + cpu_hot: cpu-hot { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "hot"; + }; + + cpu_critical: cpu-critical { + temperature = <100000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + }; + + cpu_cooling_maps: cooling-maps { + map0 { + trip = <&cpu_passive>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&cpu_hot>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + }; + onewire { + compatible = "w1-gpio"; + gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>; + #gpio-cells = <1>; + }; +}; + +&efuse { + sn: sn@32 { + reg = <0x32 0x20>; + }; + + eth_mac: eth_mac@0 { + reg = <0x0 0x6>; + }; + + bt_mac: bt_mac@6 { + reg = <0x6 0x6>; + }; + + wifi_mac: wifi_mac@c { + reg = <0xc 0x6>; + }; + + bid: bid@12 { + reg = <0x12 0x20>; + }; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rmii_x_pins>; + pinctrl-names = "default"; + phy-handle = <ð_phy0>; + phy-mode = "rmii"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + /* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */ + eth_phy0: ethernet-phy@0 { + /* compatible = "ethernet-phy-id0243.0c54";*/ + max-speed = <100>; + reg = <0>; + + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>; + }; + }; +}; + +/* Internal I2C bus (on CPU module) */ +&i2c1 { + status = "okay"; + pinctrl-0 = <&i2c1_z_pins>; + pinctrl-names = "default"; + + /* RTC */ + pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + status = "okay"; + }; +}; + +/* Peripheral I2C bus (on motherboard) */ +&i2c_AO { + status = "okay"; + pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>; + pinctrl-names = "default"; +}; + +&pwm_ab { + status = "okay"; + pinctrl-0 = <&pwm_a_x20_pins>; + pinctrl-names = "default"; +}; + +/* wifi module */ +&sd_emmc_b { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + sd-uhs-sdr104; + max-frequency = <200000000>; + non-removable; + disable-wp; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + }; +}; + +/* emmc storage */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <200000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* UART Bluetooth */ +&uart_B { + status = "okay"; + pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>; + }; +}; + +/* UART Console */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +/* UART Wireless module */ +&uart_AO_B { + status = "okay"; + pinctrl-0 = <&uart_ao_b_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + phy-supply = <&usb_pwr>; +}; + +&spicc1 { + status = "okay"; + pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>; + pinctrl-names = "default"; +}; + +&gpio { + gpio-line-names = + "", "", "", "", "", // 0 - 4 + "", "", "", "", "", // 5 - 9 + "UserButton", "", "", "", "", // 10 - 14 + "", "", "", "", "", // 15 - 19 + "", "", "", "", "", // 20 - 24 + "", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29 + "Output1", "", "", "", "", // 30 - 34 + "", "ZigBeeBOOT", "", "", "", // 35 - 39 + "", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44 + "Input2", "Input1", "", "", "", // 45 - 49 + "", "", "", "", "", // 50 - 54 + "", "", "", "", "", // 55 - 59 + "", "", "", "", "", // 60 - 64 + "", "", "", "", "", // 65 - 69 + "", "", "", "", "", // 70 - 74 + "", "", "", "", "", // 75 - 79 + "", "", "", "", "", // 80 - 84 + "", ""; // 85-86 +}; + +&cpu0 { + #cooling-cells = <2>; +}; + +&cpu1 { + #cooling-cells = <2>; +}; + +&cpu2 { + #cooling-cells = <2>; +}; + +&cpu3 { + #cooling-cells = <2>; +}; diff --git a/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts new file mode 100644 index 0000000000..6eafb90869 --- /dev/null +++ b/arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts @@ -0,0 +1,241 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in> + * Copyright (c) 2020 JetHome + * Author: Aleksandr Kazantsev <ak@tvip.ru> + * Author: Alexey Shevelkin <ash@tvip.ru> + * Author: Vyacheslav Bocharov <adeep@lexina.in> + */ + +/dts-v1/; + +#include "meson-gxl.dtsi" + +/ { + compatible = "jethome,jethub-j80", "amlogic,s905w", "amlogic,meson-gxl"; + model = "JetHome JetHub J80"; + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + reserved-memory { + linux,cma { + size = <0x0 0x1000000>; + }; + }; + + aliases { + serial0 = &uart_AO; /* Console */ + serial1 = &uart_A; /* Bluetooth */ + serial2 = &uart_AO_B; /* Wireless module 1 */ + serial3 = &uart_C; /* Wireless module 2 */ + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + vddio_ao18: regulator-vddio_ao18 { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_AO18"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddio_boot: regulator-vddio_boot { + compatible = "regulator-fixed"; + regulator-name = "VDDIO_BOOT"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + wifi32k: wifi32k { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */ + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>; + clocks = <&wifi32k>; + clock-names = "ext_clock"; + }; +}; + +&efuse { + bt_mac: bt_mac@6 { + reg = <0x6 0x6>; + }; + + wifi_mac: wifi_mac@C { + reg = <0xc 0x6>; + }; +}; + +&sn { + reg = <0x32 0x20>; +}; + +ð_mac { + reg = <0x0 0x6>; +}; + +&bid { + reg = <0x12 0x20>; +}; + +&usb { + status = "okay"; + dr_mode = "host"; +}; + +&pwm_ef { + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; + clocks = <&clkc CLKID_FCLK_DIV4>; + clock-names = "clkin0"; +}; + +&saradc { + status = "okay"; + vref-supply = <&vddio_ao18>; +}; + +/* Wireless SDIO Module */ +&sd_emmc_a { + status = "okay"; + pinctrl-0 = <&sdio_pins>; + pinctrl-1 = <&sdio_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + #address-cells = <1>; + #size-cells = <0>; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + + non-removable; + disable-wp; + + /* WiFi firmware requires power to be kept while in suspend */ + keep-power-in-suspend; + + mmc-pwrseq = <&sdio_pwrseq>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <50000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>; + + vmmc-supply = <&vddao_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + max-frequency = <200000000>; + non-removable; + disable-wp; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&vddio_boot>; +}; + +/* Console UART */ +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +/* S905W only has access to its internal PHY */ +ðmac { + status = "okay"; + phy-mode = "rmii"; + phy-handle = <&internal_phy>; +}; + +&internal_phy { + status = "okay"; + pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>; + pinctrl-names = "default"; +}; + +&uart_A { + status = "okay"; + pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; + +&uart_C { + status = "okay"; + pinctrl-0 = <&uart_c_pins>; + pinctrl-names = "default"; +}; + +&uart_AO_B { + status = "okay"; + pinctrl-0 = <&uart_ao_b_pins>, <&uart_ao_b_cts_rts_pins>; + pinctrl-names = "default"; + uart-has-rtscts; +}; + +&i2c_B { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_b_pins>; + + pcf8563: pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + status = "okay"; + }; +}; diff --git a/board/amlogic/jethub-j80/MAINTAINERS b/board/amlogic/jethub-j80/MAINTAINERS new file mode 100644 index 0000000000..459e9f89da --- /dev/null +++ b/board/amlogic/jethub-j80/MAINTAINERS @@ -0,0 +1,9 @@ +JetHome JetHub +M: Vyacheslav Bocharov <adeep@lexina.in> +S: Maintained +L: u-boot-amlogic@groups.io +F: board/amlogic/jethub-j80/ +F: configs/jethub_j80_defconfig +F: configs/jethub_j100_defconfig +F: doc/board/amlogic/jethub-j80.rst +F: doc/board/amlogic/jethub-j100.rst diff --git a/board/amlogic/jethub-j80/Makefile b/board/amlogic/jethub-j80/Makefile new file mode 100644 index 0000000000..a727a4b222 --- /dev/null +++ b/board/amlogic/jethub-j80/Makefile @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0+ +# +# (C) Copyright 2021 Vyacheslav Bocharov +# Author: Vyacheslav Bocharov <adeep@lexina.in> + +obj-y := jethub-j80.o diff --git a/board/amlogic/jethub-j80/jethub-j80.c b/board/amlogic/jethub-j80/jethub-j80.c new file mode 100644 index 0000000000..ae402303aa --- /dev/null +++ b/board/amlogic/jethub-j80/jethub-j80.c @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2021 Vyacheslav Bocharov + * Author: Vyacheslav Bocharov <adeep@lexina.in> + * Author: Neil Armstrong <narmstrong@baylibre.com> + * + */ + +#include <common.h> +#include <dm.h> +#include <adc.h> +#include <env.h> +#include <init.h> +#include <net.h> +#include <asm/io.h> +#include <asm/arch/gx.h> +#include <asm/arch/sm.h> +#include <asm/arch/eth.h> +#include <asm/arch/mem.h> + +#define EFUSE_SN_OFFSET 50 +#define EFUSE_SN_SIZE 32 +#define EFUSE_MAC_OFFSET 0 +#define EFUSE_MAC_SIZE 6 +#define EFUSE_USID_OFFSET 18 +#define EFUSE_USID_SIZE 32 + +int misc_init_r(void) +{ + u8 mac_addr[EFUSE_MAC_SIZE]; + char serial[EFUSE_SN_SIZE]; + char usid[EFUSE_USID_SIZE]; + ssize_t len; + unsigned int adcval; + int ret; + char value[16]; + + if (!eth_env_get_enetaddr("ethaddr", mac_addr)) { + len = meson_sm_read_efuse(EFUSE_MAC_OFFSET, + mac_addr, EFUSE_MAC_SIZE); + if (len == EFUSE_MAC_SIZE && is_valid_ethaddr(mac_addr)) + eth_env_set_enetaddr("ethaddr", mac_addr); + else + meson_generate_serial_ethaddr(); + } + + if (!env_get("serial")) { + len = meson_sm_read_efuse(EFUSE_SN_OFFSET, serial, + EFUSE_SN_SIZE); + if (len == EFUSE_SN_SIZE) + env_set("serial", serial); + } + + if (!env_get("usid")) { + len = meson_sm_read_efuse(EFUSE_USID_OFFSET, usid, + EFUSE_USID_SIZE); + if (len == EFUSE_USID_SIZE) + env_set("usid", usid); + } + + ret = adc_channel_single_shot("adc@8680", 0, &adcval); + if (adcval < 3000) + env_set("userbutton", "true"); + else + env_set("userbutton", "false"); + + return 0; +} diff --git a/configs/jethub_j100_defconfig b/configs/jethub_j100_defconfig new file mode 100644 index 0000000000..290ce4db85 --- /dev/null +++ b/configs/jethub_j100_defconfig @@ -0,0 +1,55 @@ +CONFIG_ARM=y +CONFIG_SYS_CONFIG_NAME="jethub" +CONFIG_ARCH_MESON=y +CONFIG_SYS_TEXT_BASE=0x01000000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ENV_SIZE=0x2000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="meson-axg-jethome-jethub-j100" +CONFIG_MESON_AXG=y +CONFIG_DEBUG_UART_BASE=0xff803000 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_IDENT_STRING=" jethubj100" +CONFIG_DEBUG_UART=y +CONFIG_OF_BOARD_SETUP=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_MISC_INIT_R=y +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_IMI is not set +CONFIG_CMD_GPIO=y +CONFIG_RANDOM_UUID=y +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_REGULATOR=y +CONFIG_PARTITION_TYPE_GUID=y +CONFIG_OF_CONTROL=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_MMC_MESON_GX=y +CONFIG_MTD_UBI=y +CONFIG_PHY_REALTEK=y +CONFIG_DM_ETH=y +CONFIG_ETH_DESIGNWARE_MESON8B=y +CONFIG_MESON_GXL_USB_PHY=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_MESON_AXG=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_RESET=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_DEBUG_UART_SKIP_INIT=y +CONFIG_MESON_SERIAL=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_DWC3_MESON_GXL=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_OF_LIBFDT_OVERLAY=y diff --git a/configs/jethub_j80_defconfig b/configs/jethub_j80_defconfig new file mode 100644 index 0000000000..7db05af3b0 --- /dev/null +++ b/configs/jethub_j80_defconfig @@ -0,0 +1,63 @@ +CONFIG_ARM=y +CONFIG_SYS_BOARD="jethub-j80" +CONFIG_SYS_CONFIG_NAME="jethub" +CONFIG_ARCH_MESON=y +CONFIG_SYS_TEXT_BASE=0x01000000 +CONFIG_NR_DRAM_BANKS=1 +CONFIG_ENV_SIZE=0x2000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="meson-gxl-s905w-jethome-jethub-j80" +CONFIG_MESON_GXL=y +CONFIG_DEBUG_UART_BASE=0xc81004c0 +CONFIG_DEBUG_UART_CLOCK=24000000 +CONFIG_IDENT_STRING=" jethubj80" +CONFIG_DEBUG_UART=y +CONFIG_OF_BOARD_SETUP=y +CONFIG_CONSOLE_MUX=y +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_MISC_INIT_R=y +# CONFIG_CMD_BDI is not set +# CONFIG_CMD_IMI is not set +CONFIG_CMD_ADC=y +CONFIG_CMD_GPIO=y +CONFIG_RANDOM_UUID=y +# CONFIG_CMD_LOADS is not set +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_REGULATOR=y +CONFIG_PARTITION_TYPE_GUID=y +CONFIG_OF_CONTROL=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_NET_RANDOM_ETHADDR=y +CONFIG_SARADC_MESON=y +CONFIG_MMC_MESON_GX=y +CONFIG_MTD_UBI=y +CONFIG_PHY_MESON_GXL=y +CONFIG_DM_ETH=y +CONFIG_DM_MDIO=y +CONFIG_DM_MDIO_MUX=y +CONFIG_ETH_DESIGNWARE_MESON8B=y +CONFIG_MDIO_MUX_MMIOREG=y +CONFIG_MESON_GXL_USB_PHY=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_MESON_GXL=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_RESET=y +CONFIG_DEBUG_UART_ANNOUNCE=y +CONFIG_DEBUG_UART_SKIP_INIT=y +CONFIG_MESON_SERIAL=y +CONFIG_USB=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC3=y +# CONFIG_USB_DWC3_GADGET is not set +CONFIG_USB_DWC3_MESON_GXL=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_VENDOR_NUM=0x1b8e +CONFIG_USB_GADGET_PRODUCT_NUM=0xfada +CONFIG_USB_GADGET_DWC2_OTG=y +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_OF_LIBFDT_OVERLAY=y -- 2.30.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs 2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov @ 2021-09-20 8:40 ` Vyacheslav Bocharov 2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong 3 siblings, 0 replies; 6+ messages in thread From: Vyacheslav Bocharov @ 2021-09-20 8:40 UTC (permalink / raw) To: Neil Armstrong; +Cc: u-boot, u-boot-amlogic Fix doc/board/amlogic/index.rst: - Add S905W to S905X column. - Add JetHub devices to the corresponding columns. - Fix tabs to spaces for table alignment Add doc/board/amlogic files: - jethub-j100.rst - jethub-j80.rst Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> --- doc/board/amlogic/index.rst | 128 +++++++++++++++--------------- doc/board/amlogic/jethub-j100.rst | 108 +++++++++++++++++++++++++ doc/board/amlogic/jethub-j80.rst | 97 ++++++++++++++++++++++ 3 files changed, 270 insertions(+), 63 deletions(-) create mode 100644 doc/board/amlogic/jethub-j100.rst create mode 100644 doc/board/amlogic/jethub-j80.rst diff --git a/doc/board/amlogic/index.rst b/doc/board/amlogic/index.rst index 2913ab281a..c18f1b7e71 100644 --- a/doc/board/amlogic/index.rst +++ b/doc/board/amlogic/index.rst @@ -10,69 +10,69 @@ An up-do-date matrix is also available on: http://linux-meson.com This matrix concerns the actual source code version. -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| | S905 | S905X | S912 | A113X | S905X2 | S922X | S905X3 | -| | | S805X | S905D | | S905D2 | A311D | S905D3 | -| | | | | | S905Y2 | | | -+===============================+===========+=================+==============+============+============+=============+==============+ -| Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 | -| | Nanopi-K2 | Khadas-VIM | Libretech-PC | | SEI510 | Khadas-VIM3 | Khadas-VIM3L | -| | P200 | LibreTech-CC v1 | WeTek Core2 | | | GT-King/Pro | Odroid-C4 | -| | P201 | LibreTech-AC v2 | | | | GSKing-X | Odroid-HC4 | -| | | | | | | | BananaPi-M5 | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Pinctrl/GPIO | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Clock Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| PWM | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Reset Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Infrared Decoder | No | No | No | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Ethernet | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Multi-core | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Fuse access | **Yes** | **Yes** |**Yes** |**Yes** |**Yes** |**Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| SPI (FC) | **Yes** | **Yes** | **Yes** | **Yes** |**Yes** | **Yes** | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| SPI (CC) | No | No | No | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| I2C | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| USB | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| USB OTG | No | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| eMMC | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| SDCard | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| NAND | No | No | No | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| ADC | **Yes** | **Yes** | **Yes** | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| CVBS Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| HDMI Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| CEC | No | No | No | *N/A* | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| Thermal Sensor | No | No | No | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| LCD/LVDS Output | No | *N/A* | No | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| MIPI DSI Output | *N/A* | *N/A* | *N/A* | No | No | No | No | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| SoC (version) information | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ -| PCIe (+NVMe) | *N/A* | *N/A* | *N/A* | **Yes** | **Yes** | **Yes** | **Yes** | -+-------------------------------+-----------+-----------------+--------------+------------+------------+-------------+--------------+ ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| | S905 | S905X | S912 | A113X | S905X2 | S922X | S905X3 | +| | | S805X | S905D | | S905D2 | A311D | S905D3 | +| | | S905W | | | S905Y2 | | | ++===============================+===========+=================+==============+=============+============+=============+==============+ +| Boards | Odroid-C2 | P212 | Khadas VIM2 | S400 | U200 | Odroid-N2 | SEI610 | +| | Nanopi-K2 | Khadas-VIM | Libretech-PC | JetHub J100 | SEI510 | Khadas-VIM3 | Khadas-VIM3L | +| | P200 | LibreTech-CC v1 | WeTek Core2 | | | GT-King/Pro | Odroid-C4 | +| | P201 | LibreTech-AC v2 | | | | GSKing-X | Odroid-HC4 | +| | | JetHub J80 | | | | | BananaPi-M5 | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| UART | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Pinctrl/GPIO | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Clock Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| PWM | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Reset Control | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Infrared Decoder | No | No | No | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Ethernet | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Multi-core | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Fuse access | **Yes** | **Yes** |**Yes** |**Yes** |**Yes** |**Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| SPI (FC) | **Yes** | **Yes** | **Yes** | **Yes** |**Yes** | **Yes** | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| SPI (CC) | No | No | No | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| I2C | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| USB | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| USB OTG | No | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| eMMC | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| SDCard | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| NAND | No | No | No | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| ADC | **Yes** | **Yes** | **Yes** | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| CVBS Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| HDMI Output | **Yes** | **Yes** | **Yes** | *N/A* | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| CEC | No | No | No | *N/A* | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| Thermal Sensor | No | No | No | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| LCD/LVDS Output | No | *N/A* | No | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| MIPI DSI Output | *N/A* | *N/A* | *N/A* | No | No | No | No | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| SoC (version) information | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ +| PCIe (+NVMe) | *N/A* | *N/A* | *N/A* | **Yes** | **Yes** | **Yes** | **Yes** | ++-------------------------------+-----------+-----------------+--------------+-------------+------------+-------------+--------------+ Board Documentation ------------------- @@ -82,6 +82,8 @@ Board Documentation beelink-gtking beelink-gtkingpro + jethub-j100 + jethub-j80 khadas-vim2 khadas-vim3l khadas-vim3 diff --git a/doc/board/amlogic/jethub-j100.rst b/doc/board/amlogic/jethub-j100.rst new file mode 100644 index 0000000000..58602787d3 --- /dev/null +++ b/doc/board/amlogic/jethub-j100.rst @@ -0,0 +1,108 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for JetHub J100 +======================= + +JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation +controller manufactured by JetHome with the following specifications: + + - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz + - no video out + - 512Mb/1GB DDR3 + - 8/16GB eMMC flash + - 1 x USB 2.0 + - 1 x 10/100Mbps ethernet + - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE + 802.11a/b/g/n/ac, Bluetooth 4.2. + - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output + power and Zigbee 3.0 support. + - 2 x gpio LEDS + - GPIO user Button + - 1 x 1-Wire + - 2 x RS-485 + - 4 x dry contact digital GPIO inputs + - 3 x relay GPIO outputs + - DC source with a voltage of 9 to 56 V / Passive POE + - DIN Rail Mounting case + +U-Boot compilation +------------------ + +.. code-block:: bash + + $ export CROSS_COMPILE=aarch64-none-elf- + $ make jethub_j100_defconfig + $ make + +Image creation +-------------- + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain binaries +from the git tree published by the board vendor: + +.. code-block:: bash + + $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot + $ cd jethub-u-boot + $ export FIPDIR=$PWD + +Go back to mainline U-boot source tree then : + +.. code-block:: bash + + $ mkdir fip + + $ cp $FIPDIR/j100/bl2.bin fip/ + $ cp $FIPDIR/j100/acs.bin fip/ + $ cp $FIPDIR/j100/bl21.bin fip/ + $ cp $FIPDIR/j100/bl30.bin fip/ + $ cp $FIPDIR/j100/bl301.bin fip/ + $ cp $FIPDIR/j100/bl31.img fip/ + $ cp u-boot.bin fip/bl33.bin + + $ $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + $ $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + $ $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl30_new.bin \ + --output fip/bl30_new.bin.enc \ + --level v3 --type bl30 + $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl31.img \ + --output fip/bl31.img.enc \ + --level v3 --type bl31 + $ $FIPDIR/j100/aml_encrypt_axg --bl3sig --input fip/bl33.bin --compress lz4 \ + --output fip/bl33.bin.enc \ + --level v3 --type bl33 + $ $FIPDIR/j100/aml_encrypt_axg --bl2sig --input fip/bl2_new.bin \ + --output fip/bl2.n.bin.sig + $ $FIPDIR/j100/aml_encrypt_axg --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc --level v3 + +and then write the image to eMMC with: + +.. code-block:: bash + + $ DEV=/dev/your_emmc_device + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 diff --git a/doc/board/amlogic/jethub-j80.rst b/doc/board/amlogic/jethub-j80.rst new file mode 100644 index 0000000000..6b7bdc78b1 --- /dev/null +++ b/doc/board/amlogic/jethub-j80.rst @@ -0,0 +1,97 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +U-Boot for JetHub J80 +====================== + +JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation +controller manufactured by JetHome with the following specifications: + + - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz + - No video out + - 1GB DDR3 + - 8/16GB eMMC flash + - 2 x USB 2.0 + - 1 x 10/100Mbps ethernet + - SDIO WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0. + - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output + power and Zigbee 3.0 support. + - MicroSD 2.x/3.x/4.x DS/HS cards. + - 1 x gpio LED + - ADC user Button + - DC source 5V microUSB + - Square plastic case + +U-Boot compilation +------------------ + +.. code-block:: bash + + $ export CROSS_COMPILE=aarch64-none-elf- + $ make jethub_j80_defconfig + $ make + +Image creation +-------------- + +Amlogic doesn't provide sources for the firmware and for tools needed +to create the bootloader image, so it is necessary to obtain binaries +from the git tree published by the board vendor: + +.. code-block:: bash + + $ git clone https://github.com/jethome-ru/jethub-aml-tools jethub-u-boot + $ cd jethub-u-boot + $ export FIPDIR=$PWD + +Go back to mainline U-Boot source tree then : + +.. code-block:: bash + + $ mkdir fip + + $ cp $FIPDIR/j80/bl2.bin fip/ + $ cp $FIPDIR/j80/acs.bin fip/ + $ cp $FIPDIR/j80/bl21.bin fip/ + $ cp $FIPDIR/j80/bl30.bin fip/ + $ cp $FIPDIR/j80/bl301.bin fip/ + $ cp $FIPDIR/j80/bl31.img fip/ + $ cp u-boot.bin fip/bl33.bin + + $ $FIPDIR/blx_fix.sh \ + fip/bl30.bin \ + fip/zero_tmp \ + fip/bl30_zero.bin \ + fip/bl301.bin \ + fip/bl301_zero.bin \ + fip/bl30_new.bin \ + bl30 + + $ python $FIPDIR/acs_tool.pyc fip/bl2.bin fip/bl2_acs.bin fip/acs.bin 0 + + $ $FIPDIR/blx_fix.sh \ + fip/bl2_acs.bin \ + fip/zero_tmp \ + fip/bl2_zero.bin \ + fip/bl21.bin \ + fip/bl21_zero.bin \ + fip/bl2_new.bin \ + bl2 + + $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl30_new.bin + $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl31.img + $ $FIPDIR/j80/aml_encrypt_gxl --bl3enc --input fip/bl33.bin --compress lz4 + $ $FIPDIR/j80/aml_encrypt_gxl --bl2sig --input fip/bl2_new.bin --output fip/bl2.n.bin.sig + $ $FIPDIR/j80/aml_encrypt_gxl --bootmk \ + --output fip/u-boot.bin \ + --bl2 fip/bl2.n.bin.sig \ + --bl30 fip/bl30_new.bin.enc \ + --bl31 fip/bl31.img.enc \ + --bl33 fip/bl33.bin.enc + +and then write the image to SD/eMMC with: + +.. code-block:: bash + + $ DEV=/dev/your_sd_device + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=512 skip=1 seek=1 + $ dd if=fip/u-boot.bin.sd.bin of=$DEV conv=fsync,notrunc bs=1 count=444 -- 2.30.2 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov ` (2 preceding siblings ...) 2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov @ 2021-09-21 7:27 ` Neil Armstrong 3 siblings, 0 replies; 6+ messages in thread From: Neil Armstrong @ 2021-09-21 7:27 UTC (permalink / raw) To: Vyacheslav Bocharov; +Cc: u-boot, u-boot-amlogic On 20/09/2021 10:40, Vyacheslav Bocharov wrote: > Add support for new home automation devices manufactured by JetHome. > Patches prepared for use with the "ARM: meson: Sync Amlogic DT from Linux 5.14" patch series by Neil Armstrong > > JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features: > - DIN Rail Mounting case > - Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz > - no video out > - 512Mb/1GB DDR3 > - 8/16GB eMMC flash > - 1 x USB 2.0 > - 1 x 10/100Mbps ethernet > - WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2. > - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. > - 2 x gpio LEDS > - GPIO user Button > - 1 x 1-Wire > - 2 x RS-485 > - 4 x dry contact digital GPIO inputs > - 3 x relay GPIO outputs > - DC source with a voltage of 9 to 56 V / Passive POE > > JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features: > - Square plastic case > - Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz > - no video out > - 1GB DDR3 > - 8/16GB eMMC flash > - 2 x USB 2.0 > - 1 x 10/100Mbps ethernet > - WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0. > - TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support. > - MicroSD 2.x/3.x/4.x DS/HS cards. > - 1 x gpio LED > - ADC user Button > - DC source 5V microUSB with serial console > > Changes from v2: > - fix "Alignment should match open parenthesis" in board/amlogic/jethub-j80/jethub-j80.c > - add missing files to board/amlogic/jethub-j80/MAINTAINERS > - fix unexpected unindent in doc files > > Changes from v1: > - fix BOOT_TARGET_DEVICES in jethub.h (patch 1/3) > - add lore URLs to description (patch 2/3) > > Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in> > > Vyacheslav Bocharov (3): > ARM: amlogic: add JetHub common config header > ARM: amlogic: add JetHub D1/H1 device support > ARM: amlogic: add JetHub D1/H1 docs > > arch/arm/dts/Makefile | 2 + > .../arm/dts/meson-axg-jethome-jethub-j100.dts | 361 ++++++++++++++++++ > .../meson-gxl-s905w-jethome-jethub-j80.dts | 241 ++++++++++++ > board/amlogic/jethub-j80/MAINTAINERS | 9 + > board/amlogic/jethub-j80/Makefile | 6 + > board/amlogic/jethub-j80/jethub-j80.c | 68 ++++ > configs/jethub_j100_defconfig | 55 +++ > configs/jethub_j80_defconfig | 63 +++ > doc/board/amlogic/index.rst | 128 ++++--- > doc/board/amlogic/jethub-j100.rst | 108 ++++++ > doc/board/amlogic/jethub-j80.rst | 97 +++++ > include/configs/jethub.h | 40 ++ > 12 files changed, 1115 insertions(+), 63 deletions(-) > create mode 100644 arch/arm/dts/meson-axg-jethome-jethub-j100.dts > create mode 100644 arch/arm/dts/meson-gxl-s905w-jethome-jethub-j80.dts > create mode 100644 board/amlogic/jethub-j80/MAINTAINERS > create mode 100644 board/amlogic/jethub-j80/Makefile > create mode 100644 board/amlogic/jethub-j80/jethub-j80.c > create mode 100644 configs/jethub_j100_defconfig > create mode 100644 configs/jethub_j80_defconfig > create mode 100644 doc/board/amlogic/jethub-j100.rst > create mode 100644 doc/board/amlogic/jethub-j80.rst > create mode 100644 include/configs/jethub.h > Applied to u-boot-amlogic-next Neil ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2021-09-21 7:28 UTC | newest] Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2021-09-20 8:40 [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 1/3] ARM: amlogic: add JetHub common config header Vyacheslav Bocharov 2021-09-20 12:30 ` Neil Armstrong 2021-09-20 8:40 ` [PATCH v3 2/3] ARM: amlogic: add JetHub D1/H1 device support Vyacheslav Bocharov 2021-09-20 8:40 ` [PATCH v3 3/3] ARM: amlogic: add JetHub D1/H1 docs Vyacheslav Bocharov 2021-09-21 7:27 ` [PATCH v3 0/3] ARM: meson: add support for JetHub D1/H1 Neil Armstrong
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.