[PATCH 0/3] Add support for the Mercury+ AA1 module

[PATCH 0/3] Add support for the Mercury+ AA1 module

[Paweł Anikiel]

The following patches add support for the Mercury+ AA1 with an
Arria 10 SoCFPGA, namely a device tree, and a fix regarding the
Arria 10 reset manager driver.

Paweł Anikiel (3):
  dt-bindings: mtd: spi-nor: add n25q00 schema
  dts: socfpga: Add Mercury+ AA1 devicetree
  reset: socfpga: add empty driver allowing consumers to probe

 .../bindings/mtd/jedec,spi-nor.yaml           |   2 +-
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 drivers/reset/reset-socfpga.c                 |  26 ++++
 4 files changed, 155 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

-- 
2.25.1

[PATCH 0/3] Add support for the Mercury+ AA1 module

[Paweł Anikiel]

The following patches add support for the Mercury+ AA1 with an
Arria 10 SoCFPGA, namely a device tree, and a fix regarding the
Arria 10 reset manager driver.

Paweł Anikiel (3):
  dt-bindings: mtd: spi-nor: add n25q00 schema
  dts: socfpga: Add Mercury+ AA1 devicetree
  reset: socfpga: add empty driver allowing consumers to probe

 .../bindings/mtd/jedec,spi-nor.yaml           |   2 +-
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 drivers/reset/reset-socfpga.c                 |  26 ++++
 4 files changed, 155 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH 0/3] Add support for the Mercury+ AA1 module

[Paweł Anikiel]

The following patches add support for the Mercury+ AA1 with an
Arria 10 SoCFPGA, namely a device tree, and a fix regarding the
Arria 10 reset manager driver.

Paweł Anikiel (3):
  dt-bindings: mtd: spi-nor: add n25q00 schema
  dts: socfpga: Add Mercury+ AA1 devicetree
  reset: socfpga: add empty driver allowing consumers to probe

 .../bindings/mtd/jedec,spi-nor.yaml           |   2 +-
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 drivers/reset/reset-socfpga.c                 |  26 ++++
 4 files changed, 155 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Paweł Anikiel]

Add schema for the n25q00 NOR flash memory.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index ed590d7c6e37..efb3c5e05c5a 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -18,7 +18,7 @@ properties:
       - items:
           - pattern: "^((((micron|spansion|st),)?\
               (m25p(40|80|16|32|64|128)|\
-              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
+              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
               atmel,at25df(321a|641|081a)|\
               everspin,mr25h(10|40|128|256)|\
               (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
-- 
2.25.1

[PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Paweł Anikiel]

Add schema for the n25q00 NOR flash memory.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index ed590d7c6e37..efb3c5e05c5a 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -18,7 +18,7 @@ properties:
       - items:
           - pattern: "^((((micron|spansion|st),)?\
               (m25p(40|80|16|32|64|128)|\
-              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
+              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
               atmel,at25df(321a|641|081a)|\
               everspin,mr25h(10|40|128|256)|\
               (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Paweł Anikiel]

Add schema for the n25q00 NOR flash memory.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
index ed590d7c6e37..efb3c5e05c5a 100644
--- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
+++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
@@ -18,7 +18,7 @@ properties:
       - items:
           - pattern: "^((((micron|spansion|st),)?\
               (m25p(40|80|16|32|64|128)|\
-              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
+              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
               atmel,at25df(321a|641|081a)|\
               everspin,mr25h(10|40|128|256)|\
               (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Paweł Anikiel]

Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 2 files changed, 128 insertions(+)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e0934180724..0a7809eb3795 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_arria10_socdk_nand.dtb \
 	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_arria10_mercury_aa1.dtb \
 	socfpga_cyclone5_chameleon96.dtb \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
new file mode 100644
index 000000000000..c13f16afa72f
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "socfpga_arria10.dtsi"
+
+/ {
+
+	model = "Enclustra Mercury AA1";
+	compatible = "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial1 = &uart1;
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&osc1 {
+	clock-frequency = <33330000>;
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+/* Following mappings are taken from arria10 socdk dts */
+&mmc {
+	status = "okay";
+	cap-sd-highspeed;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&eccmgr {
+	sdmmca-ecc@ff8c2c00 {
+		compatible = "altr,socfpga-sdmmc-ecc";
+		reg = <0xff8c2c00 0x400>;
+		altr,ecc-parent = <&mmc>;
+		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+			     <47 IRQ_TYPE_LEVEL_HIGH>,
+			     <16 IRQ_TYPE_LEVEL_HIGH>,
+			     <48 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>; /* probe for phy addr */
+
+	max-frame-size = <3800>;
+	status = "okay";
+
+	phy-handle = <&phy3>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy3: ethernet-phy@3 {
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <1860>; /* 960ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	isl12022: isl12022@6f {
+		status = "okay";
+		compatible = "isil,isl12022";
+		reg = <0x6f>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "disabled";
+
+	flash0: n25q00@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q00";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		m25p,fast-read;
+		cdns,read-delay = <4>;
+		cdns,tshsl-ns = <200>;
+		cdns,tsd2d-ns = <255>;
+		cdns,tchsh-ns = <20>;
+		cdns,tslch-ns = <20>;
+
+		part0: qspi-boot@0 {
+			label = "Flash 0 Raw Data";
+			reg = <0x0 0x01340000>;
+		};
+		part1: qspi-rootfs@1320000 {
+			label = "Flash 1 jffs2 Filesystem";
+			reg = <0x01340000 0x2cc0000>;
+		};
+	};
+};
-- 
2.25.1

[PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Paweł Anikiel]

Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 2 files changed, 128 insertions(+)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e0934180724..0a7809eb3795 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_arria10_socdk_nand.dtb \
 	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_arria10_mercury_aa1.dtb \
 	socfpga_cyclone5_chameleon96.dtb \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
new file mode 100644
index 000000000000..c13f16afa72f
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "socfpga_arria10.dtsi"
+
+/ {
+
+	model = "Enclustra Mercury AA1";
+	compatible = "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial1 = &uart1;
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&osc1 {
+	clock-frequency = <33330000>;
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+/* Following mappings are taken from arria10 socdk dts */
+&mmc {
+	status = "okay";
+	cap-sd-highspeed;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&eccmgr {
+	sdmmca-ecc@ff8c2c00 {
+		compatible = "altr,socfpga-sdmmc-ecc";
+		reg = <0xff8c2c00 0x400>;
+		altr,ecc-parent = <&mmc>;
+		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+			     <47 IRQ_TYPE_LEVEL_HIGH>,
+			     <16 IRQ_TYPE_LEVEL_HIGH>,
+			     <48 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>; /* probe for phy addr */
+
+	max-frame-size = <3800>;
+	status = "okay";
+
+	phy-handle = <&phy3>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy3: ethernet-phy@3 {
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <1860>; /* 960ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	isl12022: isl12022@6f {
+		status = "okay";
+		compatible = "isil,isl12022";
+		reg = <0x6f>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "disabled";
+
+	flash0: n25q00@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q00";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		m25p,fast-read;
+		cdns,read-delay = <4>;
+		cdns,tshsl-ns = <200>;
+		cdns,tsd2d-ns = <255>;
+		cdns,tchsh-ns = <20>;
+		cdns,tslch-ns = <20>;
+
+		part0: qspi-boot@0 {
+			label = "Flash 0 Raw Data";
+			reg = <0x0 0x01340000>;
+		};
+		part1: qspi-rootfs@1320000 {
+			label = "Flash 1 jffs2 Filesystem";
+			reg = <0x01340000 0x2cc0000>;
+		};
+	};
+};
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Paweł Anikiel]

Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
 2 files changed, 128 insertions(+)
 create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e0934180724..0a7809eb3795 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_arria10_socdk_nand.dtb \
 	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
+	socfpga_arria10_mercury_aa1.dtb \
 	socfpga_cyclone5_chameleon96.dtb \
 	socfpga_cyclone5_mcvevk.dtb \
 	socfpga_cyclone5_socdk.dtb \
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
new file mode 100644
index 000000000000..c13f16afa72f
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "socfpga_arria10.dtsi"
+
+/ {
+
+	model = "Enclustra Mercury AA1";
+	compatible = "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial1 = &uart1;
+	};
+
+	memory {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&osc1 {
+	clock-frequency = <33330000>;
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+/* Following mappings are taken from arria10 socdk dts */
+&mmc {
+	status = "okay";
+	cap-sd-highspeed;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&eccmgr {
+	sdmmca-ecc@ff8c2c00 {
+		compatible = "altr,socfpga-sdmmc-ecc";
+		reg = <0xff8c2c00 0x400>;
+		altr,ecc-parent = <&mmc>;
+		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+			     <47 IRQ_TYPE_LEVEL_HIGH>,
+			     <16 IRQ_TYPE_LEVEL_HIGH>,
+			     <48 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>; /* probe for phy addr */
+
+	max-frame-size = <3800>;
+	status = "okay";
+
+	phy-handle = <&phy3>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy3: ethernet-phy@3 {
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <1860>; /* 960ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	isl12022: isl12022@6f {
+		status = "okay";
+		compatible = "isil,isl12022";
+		reg = <0x6f>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&qspi {
+	status = "disabled";
+
+	flash0: n25q00@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "n25q00";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		m25p,fast-read;
+		cdns,read-delay = <4>;
+		cdns,tshsl-ns = <200>;
+		cdns,tsd2d-ns = <255>;
+		cdns,tchsh-ns = <20>;
+		cdns,tslch-ns = <20>;
+
+		part0: qspi-boot@0 {
+			label = "Flash 0 Raw Data";
+			reg = <0x0 0x01340000>;
+		};
+		part1: qspi-rootfs@1320000 {
+			label = "Flash 1 jffs2 Filesystem";
+			reg = <0x01340000 0x2cc0000>;
+		};
+	};
+};
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

The early reset driver doesn't ever probe, which causes consuming
devices to be unable to probe. Add an empty driver to set this device
as available, allowing consumers to probe.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
index 2a72f861f798..8c6492e5693c 100644
--- a/drivers/reset/reset-socfpga.c
+++ b/drivers/reset/reset-socfpga.c
@@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
 	for_each_matching_node(np, socfpga_early_reset_dt_ids)
 		a10_reset_init(np);
 }
+
+/*
+ * The early driver is problematic, because it doesn't register
+ * itself as a driver. This causes certain device links to prevent
+ * consumer devices from probing. The hacky solution is to register
+ * an empty driver, whose only job is to attach itself to the reset
+ * manager and call probe.
+ */
+static const struct of_device_id socfpga_reset_dt_ids[] = {
+	{ .compatible = "altr,rst-mgr", },
+	{ /* sentinel */ },
+};
+
+static int reset_simple_probe(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver reset_socfpga_driver = {
+	.probe	= reset_simple_probe,
+	.driver = {
+		.name		= "socfpga-reset",
+		.of_match_table	= socfpga_reset_dt_ids,
+	},
+};
+builtin_platform_driver(reset_socfpga_driver);
-- 
2.25.1

[PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

The early reset driver doesn't ever probe, which causes consuming
devices to be unable to probe. Add an empty driver to set this device
as available, allowing consumers to probe.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
index 2a72f861f798..8c6492e5693c 100644
--- a/drivers/reset/reset-socfpga.c
+++ b/drivers/reset/reset-socfpga.c
@@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
 	for_each_matching_node(np, socfpga_early_reset_dt_ids)
 		a10_reset_init(np);
 }
+
+/*
+ * The early driver is problematic, because it doesn't register
+ * itself as a driver. This causes certain device links to prevent
+ * consumer devices from probing. The hacky solution is to register
+ * an empty driver, whose only job is to attach itself to the reset
+ * manager and call probe.
+ */
+static const struct of_device_id socfpga_reset_dt_ids[] = {
+	{ .compatible = "altr,rst-mgr", },
+	{ /* sentinel */ },
+};
+
+static int reset_simple_probe(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver reset_socfpga_driver = {
+	.probe	= reset_simple_probe,
+	.driver = {
+		.name		= "socfpga-reset",
+		.of_match_table	= socfpga_reset_dt_ids,
+	},
+};
+builtin_platform_driver(reset_socfpga_driver);
-- 
2.25.1


______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

[PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

The early reset driver doesn't ever probe, which causes consuming
devices to be unable to probe. Add an empty driver to set this device
as available, allowing consumers to probe.

Signed-off-by: Paweł Anikiel <pan@semihalf.com>
---
 drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)

diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
index 2a72f861f798..8c6492e5693c 100644
--- a/drivers/reset/reset-socfpga.c
+++ b/drivers/reset/reset-socfpga.c
@@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
 	for_each_matching_node(np, socfpga_early_reset_dt_ids)
 		a10_reset_init(np);
 }
+
+/*
+ * The early driver is problematic, because it doesn't register
+ * itself as a driver. This causes certain device links to prevent
+ * consumer devices from probing. The hacky solution is to register
+ * an empty driver, whose only job is to attach itself to the reset
+ * manager and call probe.
+ */
+static const struct of_device_id socfpga_reset_dt_ids[] = {
+	{ .compatible = "altr,rst-mgr", },
+	{ /* sentinel */ },
+};
+
+static int reset_simple_probe(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver reset_socfpga_driver = {
+	.probe	= reset_simple_probe,
+	.driver = {
+		.name		= "socfpga-reset",
+		.of_match_table	= socfpga_reset_dt_ids,
+	},
+};
+builtin_platform_driver(reset_socfpga_driver);
-- 
2.25.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Rob Herring]

On Mon, Sep 20, 2021 at 02:41:40PM +0200, Paweł Anikiel wrote:
> Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
> Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
> Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
> Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
>  2 files changed, 128 insertions(+)
>  create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e0934180724..0a7809eb3795 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
>  	socfpga_arria10_socdk_nand.dtb \
>  	socfpga_arria10_socdk_qspi.dtb \
>  	socfpga_arria10_socdk_sdmmc.dtb \
> +	socfpga_arria10_mercury_aa1.dtb \
>  	socfpga_cyclone5_chameleon96.dtb \
>  	socfpga_cyclone5_mcvevk.dtb \
>  	socfpga_cyclone5_socdk.dtb \
> diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> new file mode 100644
> index 000000000000..c13f16afa72f
> --- /dev/null
> +++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> @@ -0,0 +1,127 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include "socfpga_arria10.dtsi"
> +
> +/ {
> +
> +	model = "Enclustra Mercury AA1";
> +	compatible = "altr,socfpga-arria10", "altr,socfpga";
> +
> +	aliases {
> +		ethernet0 = &gmac0;
> +		serial1 = &uart1;
> +	};
> +
> +	memory {

memory@0

> +		name = "memory";
> +		device_type = "memory";
> +		reg = <0x0 0x80000000>; /* 2GB */
> +	};
> +
> +	chosen {
> +		stdout-path = "serial1:115200n8";
> +	};
> +};
> +
> +&osc1 {
> +	clock-frequency = <33330000>;
> +};
> +
> +&usb0 {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +/* Following mappings are taken from arria10 socdk dts */
> +&mmc {
> +	status = "okay";
> +	cap-sd-highspeed;
> +	broken-cd;
> +	bus-width = <4>;
> +};
> +
> +&eccmgr {
> +	sdmmca-ecc@ff8c2c00 {
> +		compatible = "altr,socfpga-sdmmc-ecc";
> +		reg = <0xff8c2c00 0x400>;
> +		altr,ecc-parent = <&mmc>;
> +		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
> +			     <47 IRQ_TYPE_LEVEL_HIGH>,
> +			     <16 IRQ_TYPE_LEVEL_HIGH>,
> +			     <48 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-mode = "rgmii";
> +	phy-addr = <0xffffffff>; /* probe for phy addr */
> +
> +	max-frame-size = <3800>;
> +	status = "okay";
> +
> +	phy-handle = <&phy3>;
> +
> +	mdio0 {

'mdio' doesn't work?

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +		phy3: ethernet-phy@3 {
> +			txd0-skew-ps = <0>; /* -420ps */
> +			txd1-skew-ps = <0>; /* -420ps */
> +			txd2-skew-ps = <0>; /* -420ps */
> +			txd3-skew-ps = <0>; /* -420ps */
> +			rxd0-skew-ps = <420>; /* 0ps */
> +			rxd1-skew-ps = <420>; /* 0ps */
> +			rxd2-skew-ps = <420>; /* 0ps */
> +			rxd3-skew-ps = <420>; /* 0ps */
> +			txen-skew-ps = <0>; /* -420ps */
> +			txc-skew-ps = <1860>; /* 960ps */
> +			rxdv-skew-ps = <420>; /* 0ps */
> +			rxc-skew-ps = <1680>; /* 780ps */
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +	isl12022: isl12022@6f {
> +		status = "okay";
> +		compatible = "isil,isl12022";
> +		reg = <0x6f>;
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&qspi {
> +	status = "disabled";
> +
> +	flash0: n25q00@0 {

flash@0

> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "n25q00";
> +		reg = <0>;
> +		spi-max-frequency = <50000000>;
> +		cdns,page-size = <256>;
> +		cdns,block-size = <16>;
> +		m25p,fast-read;
> +		cdns,read-delay = <4>;
> +		cdns,tshsl-ns = <200>;
> +		cdns,tsd2d-ns = <255>;
> +		cdns,tchsh-ns = <20>;
> +		cdns,tslch-ns = <20>;
> +
> +		part0: qspi-boot@0 {

Put these under a 'partitions' node.

> +			label = "Flash 0 Raw Data";
> +			reg = <0x0 0x01340000>;
> +		};
> +		part1: qspi-rootfs@1320000 {
> +			label = "Flash 1 jffs2 Filesystem";
> +			reg = <0x01340000 0x2cc0000>;
> +		};
> +	};
> +};
> -- 
> 2.25.1
> 
> 
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Rob Herring]

On Mon, Sep 20, 2021 at 02:41:40PM +0200, Paweł Anikiel wrote:
> Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
> Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
> Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
> Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
>  2 files changed, 128 insertions(+)
>  create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e0934180724..0a7809eb3795 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
>  	socfpga_arria10_socdk_nand.dtb \
>  	socfpga_arria10_socdk_qspi.dtb \
>  	socfpga_arria10_socdk_sdmmc.dtb \
> +	socfpga_arria10_mercury_aa1.dtb \
>  	socfpga_cyclone5_chameleon96.dtb \
>  	socfpga_cyclone5_mcvevk.dtb \
>  	socfpga_cyclone5_socdk.dtb \
> diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> new file mode 100644
> index 000000000000..c13f16afa72f
> --- /dev/null
> +++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> @@ -0,0 +1,127 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include "socfpga_arria10.dtsi"
> +
> +/ {
> +
> +	model = "Enclustra Mercury AA1";
> +	compatible = "altr,socfpga-arria10", "altr,socfpga";
> +
> +	aliases {
> +		ethernet0 = &gmac0;
> +		serial1 = &uart1;
> +	};
> +
> +	memory {

memory@0

> +		name = "memory";
> +		device_type = "memory";
> +		reg = <0x0 0x80000000>; /* 2GB */
> +	};
> +
> +	chosen {
> +		stdout-path = "serial1:115200n8";
> +	};
> +};
> +
> +&osc1 {
> +	clock-frequency = <33330000>;
> +};
> +
> +&usb0 {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +/* Following mappings are taken from arria10 socdk dts */
> +&mmc {
> +	status = "okay";
> +	cap-sd-highspeed;
> +	broken-cd;
> +	bus-width = <4>;
> +};
> +
> +&eccmgr {
> +	sdmmca-ecc@ff8c2c00 {
> +		compatible = "altr,socfpga-sdmmc-ecc";
> +		reg = <0xff8c2c00 0x400>;
> +		altr,ecc-parent = <&mmc>;
> +		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
> +			     <47 IRQ_TYPE_LEVEL_HIGH>,
> +			     <16 IRQ_TYPE_LEVEL_HIGH>,
> +			     <48 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-mode = "rgmii";
> +	phy-addr = <0xffffffff>; /* probe for phy addr */
> +
> +	max-frame-size = <3800>;
> +	status = "okay";
> +
> +	phy-handle = <&phy3>;
> +
> +	mdio0 {

'mdio' doesn't work?

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +		phy3: ethernet-phy@3 {
> +			txd0-skew-ps = <0>; /* -420ps */
> +			txd1-skew-ps = <0>; /* -420ps */
> +			txd2-skew-ps = <0>; /* -420ps */
> +			txd3-skew-ps = <0>; /* -420ps */
> +			rxd0-skew-ps = <420>; /* 0ps */
> +			rxd1-skew-ps = <420>; /* 0ps */
> +			rxd2-skew-ps = <420>; /* 0ps */
> +			rxd3-skew-ps = <420>; /* 0ps */
> +			txen-skew-ps = <0>; /* -420ps */
> +			txc-skew-ps = <1860>; /* 960ps */
> +			rxdv-skew-ps = <420>; /* 0ps */
> +			rxc-skew-ps = <1680>; /* 780ps */
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +	isl12022: isl12022@6f {
> +		status = "okay";
> +		compatible = "isil,isl12022";
> +		reg = <0x6f>;
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&qspi {
> +	status = "disabled";
> +
> +	flash0: n25q00@0 {

flash@0

> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "n25q00";
> +		reg = <0>;
> +		spi-max-frequency = <50000000>;
> +		cdns,page-size = <256>;
> +		cdns,block-size = <16>;
> +		m25p,fast-read;
> +		cdns,read-delay = <4>;
> +		cdns,tshsl-ns = <200>;
> +		cdns,tsd2d-ns = <255>;
> +		cdns,tchsh-ns = <20>;
> +		cdns,tslch-ns = <20>;
> +
> +		part0: qspi-boot@0 {

Put these under a 'partitions' node.

> +			label = "Flash 0 Raw Data";
> +			reg = <0x0 0x01340000>;
> +		};
> +		part1: qspi-rootfs@1320000 {
> +			label = "Flash 1 jffs2 Filesystem";
> +			reg = <0x01340000 0x2cc0000>;
> +		};
> +	};
> +};
> -- 
> 2.25.1
> 
> 
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 2/3] dts: socfpga: Add Mercury+ AA1 devicetree

[Rob Herring]

On Mon, Sep 20, 2021 at 02:41:40PM +0200, Paweł Anikiel wrote:
> Add support for the Mercury+ AA1 module for Arria 10 SoC FPGA.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> Signed-off-by: Joanna Brozek <jbrozek@antmicro.com>
> Signed-off-by: Mariusz Glebocki <mglebocki@antmicro.com>
> Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
> Signed-off-by: Maciej Mikunda <mmikunda@antmicro.com>
> ---
>  arch/arm/boot/dts/Makefile                    |   1 +
>  .../boot/dts/socfpga_arria10_mercury_aa1.dts  | 127 ++++++++++++++++++
>  2 files changed, 128 insertions(+)
>  create mode 100644 arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e0934180724..0a7809eb3795 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1078,6 +1078,7 @@ dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
>  	socfpga_arria10_socdk_nand.dtb \
>  	socfpga_arria10_socdk_qspi.dtb \
>  	socfpga_arria10_socdk_sdmmc.dtb \
> +	socfpga_arria10_mercury_aa1.dtb \
>  	socfpga_cyclone5_chameleon96.dtb \
>  	socfpga_cyclone5_mcvevk.dtb \
>  	socfpga_cyclone5_socdk.dtb \
> diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> new file mode 100644
> index 000000000000..c13f16afa72f
> --- /dev/null
> +++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
> @@ -0,0 +1,127 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/dts-v1/;
> +
> +#include "socfpga_arria10.dtsi"
> +
> +/ {
> +
> +	model = "Enclustra Mercury AA1";
> +	compatible = "altr,socfpga-arria10", "altr,socfpga";
> +
> +	aliases {
> +		ethernet0 = &gmac0;
> +		serial1 = &uart1;
> +	};
> +
> +	memory {

memory@0

> +		name = "memory";
> +		device_type = "memory";
> +		reg = <0x0 0x80000000>; /* 2GB */
> +	};
> +
> +	chosen {
> +		stdout-path = "serial1:115200n8";
> +	};
> +};
> +
> +&osc1 {
> +	clock-frequency = <33330000>;
> +};
> +
> +&usb0 {
> +	status = "okay";
> +	dr_mode = "host";
> +};
> +
> +/* Following mappings are taken from arria10 socdk dts */
> +&mmc {
> +	status = "okay";
> +	cap-sd-highspeed;
> +	broken-cd;
> +	bus-width = <4>;
> +};
> +
> +&eccmgr {
> +	sdmmca-ecc@ff8c2c00 {
> +		compatible = "altr,socfpga-sdmmc-ecc";
> +		reg = <0xff8c2c00 0x400>;
> +		altr,ecc-parent = <&mmc>;
> +		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
> +			     <47 IRQ_TYPE_LEVEL_HIGH>,
> +			     <16 IRQ_TYPE_LEVEL_HIGH>,
> +			     <48 IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +};
> +
> +&gmac0 {
> +	phy-mode = "rgmii";
> +	phy-addr = <0xffffffff>; /* probe for phy addr */
> +
> +	max-frame-size = <3800>;
> +	status = "okay";
> +
> +	phy-handle = <&phy3>;
> +
> +	mdio0 {

'mdio' doesn't work?

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +		phy3: ethernet-phy@3 {
> +			txd0-skew-ps = <0>; /* -420ps */
> +			txd1-skew-ps = <0>; /* -420ps */
> +			txd2-skew-ps = <0>; /* -420ps */
> +			txd3-skew-ps = <0>; /* -420ps */
> +			rxd0-skew-ps = <420>; /* 0ps */
> +			rxd1-skew-ps = <420>; /* 0ps */
> +			rxd2-skew-ps = <420>; /* 0ps */
> +			rxd3-skew-ps = <420>; /* 0ps */
> +			txen-skew-ps = <0>; /* -420ps */
> +			txc-skew-ps = <1860>; /* 960ps */
> +			rxdv-skew-ps = <420>; /* 0ps */
> +			rxc-skew-ps = <1680>; /* 780ps */
> +			reg = <3>;
> +		};
> +	};
> +};
> +
> +&i2c1 {
> +	status = "okay";
> +	isl12022: isl12022@6f {
> +		status = "okay";
> +		compatible = "isil,isl12022";
> +		reg = <0x6f>;
> +	};
> +};
> +
> +&uart1 {
> +	status = "okay";
> +};
> +
> +&qspi {
> +	status = "disabled";
> +
> +	flash0: n25q00@0 {

flash@0

> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "n25q00";
> +		reg = <0>;
> +		spi-max-frequency = <50000000>;
> +		cdns,page-size = <256>;
> +		cdns,block-size = <16>;
> +		m25p,fast-read;
> +		cdns,read-delay = <4>;
> +		cdns,tshsl-ns = <200>;
> +		cdns,tsd2d-ns = <255>;
> +		cdns,tchsh-ns = <20>;
> +		cdns,tslch-ns = <20>;
> +
> +		part0: qspi-boot@0 {

Put these under a 'partitions' node.

> +			label = "Flash 0 Raw Data";
> +			reg = <0x0 0x01340000>;
> +		};
> +		part1: qspi-rootfs@1320000 {
> +			label = "Flash 1 jffs2 Filesystem";
> +			reg = <0x01340000 0x2cc0000>;
> +		};
> +	};
> +};
> -- 
> 2.25.1
> 
> 
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Rob Herring]

On Mon, 20 Sep 2021 14:41:39 +0200, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Rob Herring]

On Mon, 20 Sep 2021 14:41:39 +0200, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Rob Herring]

On Mon, 20 Sep 2021 14:41:39 +0200, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Pratyush Yadav]

+Tudor

On 20/09/21 02:41PM, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> index ed590d7c6e37..efb3c5e05c5a 100644
> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> @@ -18,7 +18,7 @@ properties:
>        - items:
>            - pattern: "^((((micron|spansion|st),)?\
>                (m25p(40|80|16|32|64|128)|\
> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\

IIUC this is supposed to only be for legacy/old flashes that started out 
using flash-specific compatibles. Any new flashes should simply use 
jedec,spi-nor unless there is a legitimate reason to do so.

Until you justify that reason,

Nacked-by: Pratyush Yadav <p.yadav@ti.com>

>                atmel,at25df(321a|641|081a)|\
>                everspin,mr25h(10|40|128|256)|\
>                (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
> -- 
> 2.25.1

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Pratyush Yadav]

+Tudor

On 20/09/21 02:41PM, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> index ed590d7c6e37..efb3c5e05c5a 100644
> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> @@ -18,7 +18,7 @@ properties:
>        - items:
>            - pattern: "^((((micron|spansion|st),)?\
>                (m25p(40|80|16|32|64|128)|\
> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\

IIUC this is supposed to only be for legacy/old flashes that started out 
using flash-specific compatibles. Any new flashes should simply use 
jedec,spi-nor unless there is a legitimate reason to do so.

Until you justify that reason,

Nacked-by: Pratyush Yadav <p.yadav@ti.com>

>                atmel,at25df(321a|641|081a)|\
>                everspin,mr25h(10|40|128|256)|\
>                (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
> -- 
> 2.25.1

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Pratyush Yadav]

+Tudor

On 20/09/21 02:41PM, Paweł Anikiel wrote:
> Add schema for the n25q00 NOR flash memory.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> index ed590d7c6e37..efb3c5e05c5a 100644
> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
> @@ -18,7 +18,7 @@ properties:
>        - items:
>            - pattern: "^((((micron|spansion|st),)?\
>                (m25p(40|80|16|32|64|128)|\
> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\

IIUC this is supposed to only be for legacy/old flashes that started out 
using flash-specific compatibles. Any new flashes should simply use 
jedec,spi-nor unless there is a legitimate reason to do so.

Until you justify that reason,

Nacked-by: Pratyush Yadav <p.yadav@ti.com>

>                atmel,at25df(321a|641|081a)|\
>                everspin,mr25h(10|40|128|256)|\
>                (mxicy|macronix),mx25l(4005a|1606e|6405d|8005|12805d|25635e)|\
> -- 
> 2.25.1

-- 
Regards,
Pratyush Yadav
Texas Instruments Inc.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

Hi Paweł,

On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> The early reset driver doesn't ever probe, which causes consuming
> devices to be unable to probe. Add an empty driver to set this device
> as available, allowing consumers to probe.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> index 2a72f861f798..8c6492e5693c 100644
> --- a/drivers/reset/reset-socfpga.c
> +++ b/drivers/reset/reset-socfpga.c
> @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
>  	for_each_matching_node(np, socfpga_early_reset_dt_ids)
>  		a10_reset_init(np);
>  }
> +
> +/*
> + * The early driver is problematic, because it doesn't register
> + * itself as a driver. This causes certain device links to prevent
> + * consumer devices from probing. The hacky solution is to register
> + * an empty driver, whose only job is to attach itself to the reset
> + * manager and call probe.
> + */
> +static const struct of_device_id socfpga_reset_dt_ids[] = {
> +	{ .compatible = "altr,rst-mgr", },
> +	{ /* sentinel */ },
> +};
> +
> +static int reset_simple_probe(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static struct platform_driver reset_socfpga_driver = {
> +	.probe	= reset_simple_probe,
> +	.driver = {
> +		.name		= "socfpga-reset",
> +		.of_match_table	= socfpga_reset_dt_ids,
> +	},
> +};
> +builtin_platform_driver(reset_socfpga_driver);

If we can just let devlink delay all consumers until the empty driver is
probed, does the reset controller have to be registered early at all?

regards
Philipp

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

Hi Paweł,

On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> The early reset driver doesn't ever probe, which causes consuming
> devices to be unable to probe. Add an empty driver to set this device
> as available, allowing consumers to probe.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> index 2a72f861f798..8c6492e5693c 100644
> --- a/drivers/reset/reset-socfpga.c
> +++ b/drivers/reset/reset-socfpga.c
> @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
>  	for_each_matching_node(np, socfpga_early_reset_dt_ids)
>  		a10_reset_init(np);
>  }
> +
> +/*
> + * The early driver is problematic, because it doesn't register
> + * itself as a driver. This causes certain device links to prevent
> + * consumer devices from probing. The hacky solution is to register
> + * an empty driver, whose only job is to attach itself to the reset
> + * manager and call probe.
> + */
> +static const struct of_device_id socfpga_reset_dt_ids[] = {
> +	{ .compatible = "altr,rst-mgr", },
> +	{ /* sentinel */ },
> +};
> +
> +static int reset_simple_probe(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static struct platform_driver reset_socfpga_driver = {
> +	.probe	= reset_simple_probe,
> +	.driver = {
> +		.name		= "socfpga-reset",
> +		.of_match_table	= socfpga_reset_dt_ids,
> +	},
> +};
> +builtin_platform_driver(reset_socfpga_driver);

If we can just let devlink delay all consumers until the empty driver is
probed, does the reset controller have to be registered early at all?

regards
Philipp

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

Hi Paweł,

On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> The early reset driver doesn't ever probe, which causes consuming
> devices to be unable to probe. Add an empty driver to set this device
> as available, allowing consumers to probe.
> 
> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> ---
>  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
> 
> diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> index 2a72f861f798..8c6492e5693c 100644
> --- a/drivers/reset/reset-socfpga.c
> +++ b/drivers/reset/reset-socfpga.c
> @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
>  	for_each_matching_node(np, socfpga_early_reset_dt_ids)
>  		a10_reset_init(np);
>  }
> +
> +/*
> + * The early driver is problematic, because it doesn't register
> + * itself as a driver. This causes certain device links to prevent
> + * consumer devices from probing. The hacky solution is to register
> + * an empty driver, whose only job is to attach itself to the reset
> + * manager and call probe.
> + */
> +static const struct of_device_id socfpga_reset_dt_ids[] = {
> +	{ .compatible = "altr,rst-mgr", },
> +	{ /* sentinel */ },
> +};
> +
> +static int reset_simple_probe(struct platform_device *pdev)
> +{
> +	return 0;
> +}
> +
> +static struct platform_driver reset_socfpga_driver = {
> +	.probe	= reset_simple_probe,
> +	.driver = {
> +		.name		= "socfpga-reset",
> +		.of_match_table	= socfpga_reset_dt_ids,
> +	},
> +};
> +builtin_platform_driver(reset_socfpga_driver);

If we can just let devlink delay all consumers until the empty driver is
probed, does the reset controller have to be registered early at all?

regards
Philipp

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

On Tue, 2021-10-05 at 13:12 +0200, Paweł Anikiel wrote:
> On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
> > Hi Paweł,
> > 
> > On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > > The early reset driver doesn't ever probe, which causes consuming
> > > devices to be unable to probe. Add an empty driver to set this device
> > > as available, allowing consumers to probe.
> > > 
> > > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > > ---
> > >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> > >  1 file changed, 26 insertions(+)
> > > 
> > > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > > index 2a72f861f798..8c6492e5693c 100644
> > > --- a/drivers/reset/reset-socfpga.c
> > > +++ b/drivers/reset/reset-socfpga.c
> > > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> > >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> > >               a10_reset_init(np);
> > >  }
> > > +
> > > +/*
> > > + * The early driver is problematic, because it doesn't register
> > > + * itself as a driver. This causes certain device links to prevent
> > > + * consumer devices from probing. The hacky solution is to register
> > > + * an empty driver, whose only job is to attach itself to the reset
> > > + * manager and call probe.
> > > + */
> > > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > > +     { .compatible = "altr,rst-mgr", },
> > > +     { /* sentinel */ },
> > > +};
> > > +
> > > +static int reset_simple_probe(struct platform_device *pdev)
> > > +{
> > > +     return 0;
> > > +}
> > > +
> > > +static struct platform_driver reset_socfpga_driver = {
> > > +     .probe  = reset_simple_probe,
> > > +     .driver = {
> > > +             .name           = "socfpga-reset",
> > > +             .of_match_table = socfpga_reset_dt_ids,
> > > +     },
> > > +};
> > > +builtin_platform_driver(reset_socfpga_driver);
> > 
> > If we can just let devlink delay all consumers until the empty driver is
> > probed, does the reset controller have to be registered early at all?
> > 
> > regards
> > Philipp
> 
> I asked Dinh if the reset controller code needs to be called early:
> 
> > That's correct. It's for one of the SP timers.

Ah, right, those call of_reset_control_get() from TIMER_OF_DECLARE().
Thank you, I'll apply this to reset/fixes.

regards
Philipp

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

On Tue, 2021-10-05 at 13:12 +0200, Paweł Anikiel wrote:
> On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
> > Hi Paweł,
> > 
> > On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > > The early reset driver doesn't ever probe, which causes consuming
> > > devices to be unable to probe. Add an empty driver to set this device
> > > as available, allowing consumers to probe.
> > > 
> > > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > > ---
> > >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> > >  1 file changed, 26 insertions(+)
> > > 
> > > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > > index 2a72f861f798..8c6492e5693c 100644
> > > --- a/drivers/reset/reset-socfpga.c
> > > +++ b/drivers/reset/reset-socfpga.c
> > > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> > >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> > >               a10_reset_init(np);
> > >  }
> > > +
> > > +/*
> > > + * The early driver is problematic, because it doesn't register
> > > + * itself as a driver. This causes certain device links to prevent
> > > + * consumer devices from probing. The hacky solution is to register
> > > + * an empty driver, whose only job is to attach itself to the reset
> > > + * manager and call probe.
> > > + */
> > > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > > +     { .compatible = "altr,rst-mgr", },
> > > +     { /* sentinel */ },
> > > +};
> > > +
> > > +static int reset_simple_probe(struct platform_device *pdev)
> > > +{
> > > +     return 0;
> > > +}
> > > +
> > > +static struct platform_driver reset_socfpga_driver = {
> > > +     .probe  = reset_simple_probe,
> > > +     .driver = {
> > > +             .name           = "socfpga-reset",
> > > +             .of_match_table = socfpga_reset_dt_ids,
> > > +     },
> > > +};
> > > +builtin_platform_driver(reset_socfpga_driver);
> > 
> > If we can just let devlink delay all consumers until the empty driver is
> > probed, does the reset controller have to be registered early at all?
> > 
> > regards
> > Philipp
> 
> I asked Dinh if the reset controller code needs to be called early:
> 
> > That's correct. It's for one of the SP timers.

Ah, right, those call of_reset_control_get() from TIMER_OF_DECLARE().
Thank you, I'll apply this to reset/fixes.

regards
Philipp

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Philipp Zabel]

On Tue, 2021-10-05 at 13:12 +0200, Paweł Anikiel wrote:
> On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
> > Hi Paweł,
> > 
> > On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > > The early reset driver doesn't ever probe, which causes consuming
> > > devices to be unable to probe. Add an empty driver to set this device
> > > as available, allowing consumers to probe.
> > > 
> > > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > > ---
> > >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> > >  1 file changed, 26 insertions(+)
> > > 
> > > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > > index 2a72f861f798..8c6492e5693c 100644
> > > --- a/drivers/reset/reset-socfpga.c
> > > +++ b/drivers/reset/reset-socfpga.c
> > > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> > >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> > >               a10_reset_init(np);
> > >  }
> > > +
> > > +/*
> > > + * The early driver is problematic, because it doesn't register
> > > + * itself as a driver. This causes certain device links to prevent
> > > + * consumer devices from probing. The hacky solution is to register
> > > + * an empty driver, whose only job is to attach itself to the reset
> > > + * manager and call probe.
> > > + */
> > > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > > +     { .compatible = "altr,rst-mgr", },
> > > +     { /* sentinel */ },
> > > +};
> > > +
> > > +static int reset_simple_probe(struct platform_device *pdev)
> > > +{
> > > +     return 0;
> > > +}
> > > +
> > > +static struct platform_driver reset_socfpga_driver = {
> > > +     .probe  = reset_simple_probe,
> > > +     .driver = {
> > > +             .name           = "socfpga-reset",
> > > +             .of_match_table = socfpga_reset_dt_ids,
> > > +     },
> > > +};
> > > +builtin_platform_driver(reset_socfpga_driver);
> > 
> > If we can just let devlink delay all consumers until the empty driver is
> > probed, does the reset controller have to be registered early at all?
> > 
> > regards
> > Philipp
> 
> I asked Dinh if the reset controller code needs to be called early:
> 
> > That's correct. It's for one of the SP timers.

Ah, right, those call of_reset_control_get() from TIMER_OF_DECLARE().
Thank you, I'll apply this to reset/fixes.

regards
Philipp

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
>
> Hi Paweł,
>
> On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > The early reset driver doesn't ever probe, which causes consuming
> > devices to be unable to probe. Add an empty driver to set this device
> > as available, allowing consumers to probe.
> >
> > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > ---
> >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> >  1 file changed, 26 insertions(+)
> >
> > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > index 2a72f861f798..8c6492e5693c 100644
> > --- a/drivers/reset/reset-socfpga.c
> > +++ b/drivers/reset/reset-socfpga.c
> > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> >               a10_reset_init(np);
> >  }
> > +
> > +/*
> > + * The early driver is problematic, because it doesn't register
> > + * itself as a driver. This causes certain device links to prevent
> > + * consumer devices from probing. The hacky solution is to register
> > + * an empty driver, whose only job is to attach itself to the reset
> > + * manager and call probe.
> > + */
> > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > +     { .compatible = "altr,rst-mgr", },
> > +     { /* sentinel */ },
> > +};
> > +
> > +static int reset_simple_probe(struct platform_device *pdev)
> > +{
> > +     return 0;
> > +}
> > +
> > +static struct platform_driver reset_socfpga_driver = {
> > +     .probe  = reset_simple_probe,
> > +     .driver = {
> > +             .name           = "socfpga-reset",
> > +             .of_match_table = socfpga_reset_dt_ids,
> > +     },
> > +};
> > +builtin_platform_driver(reset_socfpga_driver);
>
> If we can just let devlink delay all consumers until the empty driver is
> probed, does the reset controller have to be registered early at all?
>
> regards
> Philipp

I asked Dinh if the reset controller code needs to be called early:

>That's correct. It's for one of the SP timers.
>
>On 9/16/21 6:13 AM, Paweł Anikiel wrote:
>> Hi,
>>
>> I would like to ask you about the following commit:
>>> commit b3ca9888f35fa6919569cf27c929dc0ac49e9716
>>> Author: Dinh Nguyen <dinguyen@kernel.org>
>>> Date:   Tue Nov 13 12:50:48 2018 -0600
>>>
>>>      reset: socfpga: add an early reset driver for SoCFPGA
>>>
>>>      Create a separate reset driver that uses the reset operations in
>>>      reset-simple. The reset driver for the SoCFPGA platform needs to
>>>      register early in order to be able bring online timers that needed
>>>      early in the kernel bootup.
>>>      [...]
>> Which online timers is this commit message referring to? I couldn't find
>> any information about this. Without this patch the kernel seems to work
>> fine on an Arria 10 (with Mercury AA1 module). What's the exact reason
>> a regular platform driver isn't sufficient?
>>
>> Best regards,
>> Paweł
>>

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
>
> Hi Paweł,
>
> On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > The early reset driver doesn't ever probe, which causes consuming
> > devices to be unable to probe. Add an empty driver to set this device
> > as available, allowing consumers to probe.
> >
> > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > ---
> >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> >  1 file changed, 26 insertions(+)
> >
> > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > index 2a72f861f798..8c6492e5693c 100644
> > --- a/drivers/reset/reset-socfpga.c
> > +++ b/drivers/reset/reset-socfpga.c
> > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> >               a10_reset_init(np);
> >  }
> > +
> > +/*
> > + * The early driver is problematic, because it doesn't register
> > + * itself as a driver. This causes certain device links to prevent
> > + * consumer devices from probing. The hacky solution is to register
> > + * an empty driver, whose only job is to attach itself to the reset
> > + * manager and call probe.
> > + */
> > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > +     { .compatible = "altr,rst-mgr", },
> > +     { /* sentinel */ },
> > +};
> > +
> > +static int reset_simple_probe(struct platform_device *pdev)
> > +{
> > +     return 0;
> > +}
> > +
> > +static struct platform_driver reset_socfpga_driver = {
> > +     .probe  = reset_simple_probe,
> > +     .driver = {
> > +             .name           = "socfpga-reset",
> > +             .of_match_table = socfpga_reset_dt_ids,
> > +     },
> > +};
> > +builtin_platform_driver(reset_socfpga_driver);
>
> If we can just let devlink delay all consumers until the empty driver is
> probed, does the reset controller have to be registered early at all?
>
> regards
> Philipp

I asked Dinh if the reset controller code needs to be called early:

>That's correct. It's for one of the SP timers.
>
>On 9/16/21 6:13 AM, Paweł Anikiel wrote:
>> Hi,
>>
>> I would like to ask you about the following commit:
>>> commit b3ca9888f35fa6919569cf27c929dc0ac49e9716
>>> Author: Dinh Nguyen <dinguyen@kernel.org>
>>> Date:   Tue Nov 13 12:50:48 2018 -0600
>>>
>>>      reset: socfpga: add an early reset driver for SoCFPGA
>>>
>>>      Create a separate reset driver that uses the reset operations in
>>>      reset-simple. The reset driver for the SoCFPGA platform needs to
>>>      register early in order to be able bring online timers that needed
>>>      early in the kernel bootup.
>>>      [...]
>> Which online timers is this commit message referring to? I couldn't find
>> any information about this. Without this patch the kernel seems to work
>> fine on an Arria 10 (with Mercury AA1 module). What's the exact reason
>> a regular platform driver isn't sufficient?
>>
>> Best regards,
>> Paweł
>>

______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 3/3] reset: socfpga: add empty driver allowing consumers to probe

[Paweł Anikiel]

On Tue, Oct 5, 2021 at 11:34 AM Philipp Zabel <p.zabel@pengutronix.de> wrote:
>
> Hi Paweł,
>
> On Mon, 2021-09-20 at 14:41 +0200, Paweł Anikiel wrote:
> > The early reset driver doesn't ever probe, which causes consuming
> > devices to be unable to probe. Add an empty driver to set this device
> > as available, allowing consumers to probe.
> >
> > Signed-off-by: Paweł Anikiel <pan@semihalf.com>
> > ---
> >  drivers/reset/reset-socfpga.c | 26 ++++++++++++++++++++++++++
> >  1 file changed, 26 insertions(+)
> >
> > diff --git a/drivers/reset/reset-socfpga.c b/drivers/reset/reset-socfpga.c
> > index 2a72f861f798..8c6492e5693c 100644
> > --- a/drivers/reset/reset-socfpga.c
> > +++ b/drivers/reset/reset-socfpga.c
> > @@ -92,3 +92,29 @@ void __init socfpga_reset_init(void)
> >       for_each_matching_node(np, socfpga_early_reset_dt_ids)
> >               a10_reset_init(np);
> >  }
> > +
> > +/*
> > + * The early driver is problematic, because it doesn't register
> > + * itself as a driver. This causes certain device links to prevent
> > + * consumer devices from probing. The hacky solution is to register
> > + * an empty driver, whose only job is to attach itself to the reset
> > + * manager and call probe.
> > + */
> > +static const struct of_device_id socfpga_reset_dt_ids[] = {
> > +     { .compatible = "altr,rst-mgr", },
> > +     { /* sentinel */ },
> > +};
> > +
> > +static int reset_simple_probe(struct platform_device *pdev)
> > +{
> > +     return 0;
> > +}
> > +
> > +static struct platform_driver reset_socfpga_driver = {
> > +     .probe  = reset_simple_probe,
> > +     .driver = {
> > +             .name           = "socfpga-reset",
> > +             .of_match_table = socfpga_reset_dt_ids,
> > +     },
> > +};
> > +builtin_platform_driver(reset_socfpga_driver);
>
> If we can just let devlink delay all consumers until the empty driver is
> probed, does the reset controller have to be registered early at all?
>
> regards
> Philipp

I asked Dinh if the reset controller code needs to be called early:

>That's correct. It's for one of the SP timers.
>
>On 9/16/21 6:13 AM, Paweł Anikiel wrote:
>> Hi,
>>
>> I would like to ask you about the following commit:
>>> commit b3ca9888f35fa6919569cf27c929dc0ac49e9716
>>> Author: Dinh Nguyen <dinguyen@kernel.org>
>>> Date:   Tue Nov 13 12:50:48 2018 -0600
>>>
>>>      reset: socfpga: add an early reset driver for SoCFPGA
>>>
>>>      Create a separate reset driver that uses the reset operations in
>>>      reset-simple. The reset driver for the SoCFPGA platform needs to
>>>      register early in order to be able bring online timers that needed
>>>      early in the kernel bootup.
>>>      [...]
>> Which online timers is this commit message referring to? I couldn't find
>> any information about this. Without this patch the kernel seems to work
>> fine on an Arria 10 (with Mercury AA1 module). What's the exact reason
>> a regular platform driver isn't sufficient?
>>
>> Best regards,
>> Paweł
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Tudor.Ambarus]

On 9/23/21 9:59 PM, Pratyush Yadav wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> 
> +Tudor
> 
> On 20/09/21 02:41PM, Paweł Anikiel wrote:
>> Add schema for the n25q00 NOR flash memory.
>>
>> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
>> ---
>>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> index ed590d7c6e37..efb3c5e05c5a 100644
>> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> @@ -18,7 +18,7 @@ properties:
>>        - items:
>>            - pattern: "^((((micron|spansion|st),)?\
>>                (m25p(40|80|16|32|64|128)|\
>> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
>> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
> 
> IIUC this is supposed to only be for legacy/old flashes that started out
> using flash-specific compatibles. Any new flashes should simply use
> jedec,spi-nor unless there is a legitimate reason to do so.

that's correct, the generic compatible should suffice for these flashes.

> 
> Until you justify that reason,
> 
> Nacked-by: Pratyush Yadav <p.yadav@ti.com>

I agree.

Cheers,
ta

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Tudor.Ambarus]

On 9/23/21 9:59 PM, Pratyush Yadav wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> 
> +Tudor
> 
> On 20/09/21 02:41PM, Paweł Anikiel wrote:
>> Add schema for the n25q00 NOR flash memory.
>>
>> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
>> ---
>>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> index ed590d7c6e37..efb3c5e05c5a 100644
>> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> @@ -18,7 +18,7 @@ properties:
>>        - items:
>>            - pattern: "^((((micron|spansion|st),)?\
>>                (m25p(40|80|16|32|64|128)|\
>> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
>> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
> 
> IIUC this is supposed to only be for legacy/old flashes that started out
> using flash-specific compatibles. Any new flashes should simply use
> jedec,spi-nor unless there is a legitimate reason to do so.

that's correct, the generic compatible should suffice for these flashes.

> 
> Until you justify that reason,
> 
> Nacked-by: Pratyush Yadav <p.yadav@ti.com>

I agree.

Cheers,
ta
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/

Re: [PATCH 1/3] dt-bindings: mtd: spi-nor: add n25q00 schema

[Tudor.Ambarus]

On 9/23/21 9:59 PM, Pratyush Yadav wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know the content is safe
> 
> +Tudor
> 
> On 20/09/21 02:41PM, Paweł Anikiel wrote:
>> Add schema for the n25q00 NOR flash memory.
>>
>> Signed-off-by: Paweł Anikiel <pan@semihalf.com>
>> ---
>>  Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml | 2 +-
>>  1 file changed, 1 insertion(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> index ed590d7c6e37..efb3c5e05c5a 100644
>> --- a/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> +++ b/Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml
>> @@ -18,7 +18,7 @@ properties:
>>        - items:
>>            - pattern: "^((((micron|spansion|st),)?\
>>                (m25p(40|80|16|32|64|128)|\
>> -              n25q(32b|064|128a11|128a13|256a|512a|164k)))|\
>> +              n25q(00|32b|064|128a11|128a13|256a|512a|164k)))|\
> 
> IIUC this is supposed to only be for legacy/old flashes that started out
> using flash-specific compatibles. Any new flashes should simply use
> jedec,spi-nor unless there is a legitimate reason to do so.

that's correct, the generic compatible should suffice for these flashes.

> 
> Until you justify that reason,
> 
> Nacked-by: Pratyush Yadav <p.yadav@ti.com>

I agree.

Cheers,
ta
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel