[PATCH v8 0/3] Add APNE PCMCIA 100 Mbit support

[PATCH v8 0/3] Add APNE PCMCIA 100 Mbit support

[Michael Schmitz]

The first patch enables the use of core PCMCIA code to parse
config table entries in Amiga drivers. The remaining two patches
add 16 bit IO support to the m68k low-level IO access code, and 
add code to the APNE driver to autoprobe for 16 bit IO on cards
that support it (the 100 Mbit cards). The core PCMCIA config
table parser is utilized for this (may be built as a module).

Tested by Alex on a 100 Mbit card. Not yet tested on 10 Mbit
cards - if any of those also have the 16 bit IO feature set
in their config table, this patch series would break on those
cards. 

Note that only patch 3 has been sent to netdev. Please CC
linux-m68k when providing comments.

Cheers,

   Michael

[PATCH v7 1/3] m68k: amiga/pcmcia - add 16 bit detection interface to amipcmcia.h

[Michael Schmitz]

Add the interface definitions for 16 bit card autoprobing (using
the generic PCMCIA cftable entry parser) to amipcmcia.h for use
by apne.c.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

--

Changes from v7:

- add interface definitions only, move actual code to apne.c
---
 arch/m68k/include/asm/amipcmcia.h | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/m68k/include/asm/amipcmcia.h b/arch/m68k/include/asm/amipcmcia.h
index 6f1ec1887d82..ecaeb583004f 100644
--- a/arch/m68k/include/asm/amipcmcia.h
+++ b/arch/m68k/include/asm/amipcmcia.h
@@ -64,6 +64,7 @@ static inline void pcmcia_disable_irq(void)
 #define PCMCIA_SPEED_250NS	250
 #define PCMCIA_SPEED_720NS	720
 
+#ifndef _LINUX_CISTPL_H
 /* PCMCIA Tuple codes */
 
 #define CISTPL_NULL		0x00
@@ -106,5 +107,8 @@ static inline void pcmcia_disable_irq(void)
 #define CISTPL_FUNCID_NETWORK	0x06
 #define CISTPL_FUNCID_AIMS	0x07
 #define CISTPL_FUNCID_SCSI	0x08
+#else	/* defined _LINUX_CISTPL_H */
+extern int pcmcia_parse_tuple(tuple_t *cftuple, cisparse_t *cfparse);
+#endif
 
 #endif
-- 
2.17.1

[PATCH v7 2/3] m68k: io_mm.h - add APNE 100 MBit support

[Michael Schmitz]

Add code to support 10 Mbit and 100 Mbit mode for APNE driver.

A new ISA type ISA_TYPE_AG16 dynamically switches the Amiga
ISA inb accessor to word access as required by the 100 Mbit cards.

Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
100 MBit card support" submitted to netdev 2018/09/16 by Alex
Kazik <alex@kazik.de>.

Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

--
Changes from v4:

Geert Uytterhoeven:
- drop CONFIG_APNE100MBIT ifdefs

Changes from v3:

Finn Thain:
- revert isa_inb() define reordering
- omit redundant #ifdef around ISA_TYPE_AG16 case labels

Changes from v1:

Andreas Schwab:
- remove redundant fallthrough annotations

Changes from RFC:

Geert Uytterhoeven:
- rename ISA_TYPE_AG100 to ISA_TYPE_AG16 (16 bit cards)
- move ISA_TYPE_AG16 case inside #ifdef CONFIG_AMIGA_PCMCIA
- change #if defined(CONFIG_APNE_100MBIT) to #ifdef
- fix parentheses in isa_inb() define
- omit comment about compiler optimization

- add ISA_TYPE_AG16 case to isa_delay()
---
 arch/m68k/include/asm/io_mm.h | 16 +++++++++++-----
 1 file changed, 11 insertions(+), 5 deletions(-)

diff --git a/arch/m68k/include/asm/io_mm.h b/arch/m68k/include/asm/io_mm.h
index 9c521b048e57..68922ef42e04 100644
--- a/arch/m68k/include/asm/io_mm.h
+++ b/arch/m68k/include/asm/io_mm.h
@@ -65,12 +65,10 @@
 #define AG_ISA_IO_B(ioaddr) ( GAYLE_IO+(ioaddr)+(((ioaddr)&1)*GAYLE_ODD) )
 #define AG_ISA_IO_W(ioaddr) ( GAYLE_IO+(ioaddr) )
 
-#ifndef MULTI_ISA
-#define MULTI_ISA 0
-#else
+#ifdef MULTI_ISA
 #undef MULTI_ISA
-#define MULTI_ISA 1
 #endif
+#define MULTI_ISA 1	/* Need MULTI_ISA for 16 bit PCMCIA card support ! */
 #endif /* AMIGA_PCMCIA */
 
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -101,6 +99,8 @@
 #define ISA_TYPE_Q40  (1)
 #define ISA_TYPE_AG   (2)
 #define ISA_TYPE_ENEC (3)
+#define ISA_TYPE_AG16 (4)	/* for 100 MBit APNE card */
+
 
 #if defined(CONFIG_Q40) && !defined(MULTI_ISA)
 #define ISA_TYPE ISA_TYPE_Q40
@@ -136,6 +136,7 @@ static inline u8 __iomem *isa_itb(unsigned long addr)
     case ISA_TYPE_Q40: return (u8 __iomem *)Q40_ISA_IO_B(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u8 __iomem *)AG_ISA_IO_B(addr);
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -155,6 +156,7 @@ static inline u16 __iomem *isa_itw(unsigned long addr)
     case ISA_TYPE_Q40: return (u16 __iomem *)Q40_ISA_IO_W(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u16 __iomem *)AG_ISA_IO_W(addr);
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -171,6 +173,7 @@ static inline u32 __iomem *isa_itl(unsigned long addr)
   switch(ISA_TYPE)
     {
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u32 __iomem *)AG_ISA_IO_W(addr);
 #endif
     }
@@ -184,6 +187,7 @@ static inline u8 __iomem *isa_mtb(unsigned long addr)
     case ISA_TYPE_Q40: return (u8 __iomem *)Q40_ISA_MEM_B(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u8 __iomem *)addr;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -203,6 +207,7 @@ static inline u16 __iomem *isa_mtw(unsigned long addr)
     case ISA_TYPE_Q40: return (u16 __iomem *)Q40_ISA_MEM_W(addr);
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16:
     case ISA_TYPE_AG: return (u16 __iomem *)addr;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
@@ -216,7 +221,7 @@ static inline u16 __iomem *isa_mtw(unsigned long addr)
 }
 
 
-#define isa_inb(port)      in_8(isa_itb(port))
+#define isa_inb(port)      ((ISA_TYPE == ISA_TYPE_AG16) ? ((port) & 1 ? isa_inw((port) - 1) & 0xff : isa_inw(port) >> 8) : in_8(isa_itb(port)))
 #define isa_inw(port)      (ISA_SEX ? in_be16(isa_itw(port)) : in_le16(isa_itw(port)))
 #define isa_inl(port)      (ISA_SEX ? in_be32(isa_itl(port)) : in_le32(isa_itl(port)))
 #define isa_outb(val,port) out_8(isa_itb(port),(val))
@@ -270,6 +275,7 @@ static inline void isa_delay(void)
     case ISA_TYPE_Q40: isa_outb(0,0x80); break;
 #endif
 #ifdef CONFIG_AMIGA_PCMCIA
+    case ISA_TYPE_AG16: break;
     case ISA_TYPE_AG: break;
 #endif
 #ifdef CONFIG_ATARI_ROM_ISA
-- 
2.17.1

[PATCH v7 3/3] net/8390: apne.c - add 100 Mbit support to apne.c driver

[Michael Schmitz]

Add module parameter, IO mode autoprobe and PCMCIA reset code
required to support 100 Mbit PCMCIA ethernet cards on Amiga.

Select core PCMCIA support modules for use by APNE driver.

10 Mbit and 100 Mbit mode are supported by the same module.
Use the core PCMCIA cftable parser to detect 16 bit cards,
and automatically enable 16 bit ISA IO access for those cards
by changing isa_type at runtime. Code to reset the PCMCIA
hardware required for 16 bit cards is also added to the driver
probe.

An optional module parameter switches Amiga ISA IO accessors
to 8 or 16 bit access in case autoprobe fails.

Patch modified after patch "[PATCH RFC net-next] Amiga PCMCIA
100 MBit card support" submitted to netdev 2018/09/16 by Alex
Kazik <alex@kazik.de>.

CC: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/1622958877-2026-1-git-send-email-schmitzmic@gmail.com
Tested-by: Alex Kazik <alex@kazik.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>

--

Changes from v7:

- move 'select' for PCCARD and PCMCIA to 8390 Kconfig, so
  Amiga pcmcia.c may remain built-in while core PCMCIA
  code can be built as modules if APNE driver is a module.
- move 16 bit mode autoprobe code from amiga/pcmcia.c to this
  driver, to allow the core PCMCIA code we depend on to be
  built as modules.
- change module parameter type from bool to int to allow for
  tri-state semantics (autoprobe, 8 bit, 16 bit).

Changes from v6:

- use 16 bit mode autoprobe based on PCMCIA config table data

Changes from v5:

- move autoprobe code to new patch in this series

Geert Uytterhoeven:
- reword Kconfig help text

Finn Thain:
- style fixes, use msec_to_jiffies in timeout calc

Alex Kazik:
- revert module parameter permission change

Changes from v4:

Geert Uytterhoeven:
- remove APNE100MBIT config option, always include 16 bit support
- change module parameter permissions
- try autoprobing for 16 bit mode early on in device probe

Changes from v3:

- change module parameter name to match Kconfig help

Finn Thain:
- fix coding style in new card reset code block
- allow reset of isa_type by module parameter

Changes from v1:

- fix module parameter name in Kconfig help text

Alex Kazik:
- change module parameter type to bool, fix module parameter
  permission

Changes from RFC:

Geert Uytterhoeven:
- change APNE_100MBIT to depend on APNE
- change '---help---' to 'help' (former no longer supported)
- fix whitespace errors
- fix module_param_named() arg count
- protect all added code by #ifdef CONFIG_APNE_100MBIT

change module parameter - 0 for 8 bit, 1 for 16 bit, else autoprobe
---
 drivers/net/ethernet/8390/Kconfig |  9 ++++
 drivers/net/ethernet/8390/apne.c  | 69 +++++++++++++++++++++++++++++++
 2 files changed, 78 insertions(+)

diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index a4130e643342..b22c3cf96560 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -136,6 +136,8 @@ config NE2K_PCI
 config APNE
 	tristate "PCMCIA NE2000 support"
 	depends on AMIGA_PCMCIA
+	select PCCARD
+	select PCMCIA
 	select CRC32
 	help
 	  If you have a PCMCIA NE2000 compatible adapter, say Y.  Otherwise,
@@ -144,6 +146,13 @@ config APNE
 	  To compile this driver as a module, choose M here: the module
 	  will be called apne.
 
+	  The driver also supports 10/100Mbit cards (e.g. Netgear FA411,
+	  CNet Singlepoint). To activate 100 Mbit support, use the kernel
+	  option apne.100mbit=1 (builtin) at boot time, or the apne.100mbit
+	  module parameter. The driver will attempt to autoprobe 100 Mbit
+	  mode, so this option may not be necessary. Use apne.100mbit=0
+	  should autoprobe mis-detect a 100 Mbit card.
+
 config PCMCIA_PCNET
 	tristate "NE2000 compatible PCMCIA support"
 	depends on PCMCIA
diff --git a/drivers/net/ethernet/8390/apne.c b/drivers/net/ethernet/8390/apne.c
index da1ae37a9d73..115c008a129c 100644
--- a/drivers/net/ethernet/8390/apne.c
+++ b/drivers/net/ethernet/8390/apne.c
@@ -38,6 +38,7 @@
 #include <linux/etherdevice.h>
 #include <linux/interrupt.h>
 #include <linux/jiffies.h>
+#include <pcmcia/cistpl.h>
 
 #include <asm/io.h>
 #include <asm/setup.h>
@@ -87,6 +88,7 @@ static void apne_block_output(struct net_device *dev, const int count,
 static irqreturn_t apne_interrupt(int irq, void *dev_id);
 
 static int init_pcmcia(void);
+static int pcmcia_is_16bit(void);
 
 /* IO base address used for nic */
 
@@ -119,6 +121,10 @@ static u32 apne_msg_enable;
 module_param_named(msg_enable, apne_msg_enable, uint, 0444);
 MODULE_PARM_DESC(msg_enable, "Debug message level (see linux/netdevice.h for bitmap)");
 
+static u32 apne_100_mbit = -1;
+module_param_named(100_mbit, apne_100_mbit, uint, 0444);
+MODULE_PARM_DESC(100_mbit, "Enable 100 Mbit support");
+
 static struct net_device * __init apne_probe(void)
 {
 	struct net_device *dev;
@@ -140,6 +146,13 @@ static struct net_device * __init apne_probe(void)
 
 	pr_info("Looking for PCMCIA ethernet card : ");
 
+	if (apne_100_mbit == 1)
+		isa_type = ISA_TYPE_AG16;
+	else if (apne_100_mbit == 0)
+		isa_type = ISA_TYPE_AG;
+	else
+		pr_cont(" (autoprobing 16 bit mode) ");
+
 	/* check if a card is inserted */
 	if (!(PCMCIA_INSERTED)) {
 		pr_cont("NO PCMCIA card inserted\n");
@@ -167,6 +180,14 @@ static struct net_device * __init apne_probe(void)
 
 	pr_cont("ethernet PCMCIA card inserted\n");
 
+#if IS_ENABLED(CONFIG_PCMCIA)
+	if (apne_100_mbit < 0 && pcmcia_is_16bit()) {
+		pr_info("16-bit PCMCIA card detected!\n");
+		isa_type = ISA_TYPE_AG16;
+		apne_100_mbit = 1;
+	}
+#endif
+
 	if (!init_pcmcia()) {
 		/* XXX: shouldn't we re-enable irq here? */
 		free_netdev(dev);
@@ -583,6 +604,16 @@ static int init_pcmcia(void)
 #endif
 	u_long offset;
 
+	/* reset card (idea taken from CardReset by Artur Pogoda) */
+	if (isa_type == ISA_TYPE_AG16) {
+		u_char tmp = gayle.intreq;
+
+		gayle.intreq = 0xff;
+		mdelay(1);
+		gayle.intreq = tmp;
+		mdelay(300);
+	}
+
 	pcmcia_reset();
 	pcmcia_program_voltage(PCMCIA_0V);
 	pcmcia_access_speed(PCMCIA_SPEED_250NS);
@@ -616,4 +647,42 @@ static int init_pcmcia(void)
 	return 1;
 }
 
+#if IS_ENABLED(CONFIG_PCMCIA)
+static int pcmcia_is_16bit(void)
+{
+	u_char cftuple[258];
+	int cftuple_len;
+	tuple_t cftable_tuple;
+	cistpl_cftable_entry_t cftable_entry;
+
+	cftuple_len = pcmcia_copy_tuple(CISTPL_CFTABLE_ENTRY, cftuple, 256);
+	if (cftuple_len < 3)
+		return 0;
+#ifdef DEBUG
+	else
+		print_hex_dump(KERN_WARNING, "cftable: ", DUMP_PREFIX_NONE, 8,
+			       sizeof(char), cftuple, cftuple_len, false);
+#endif
+
+	/* build tuple_t struct and call pcmcia_parse_tuple */
+	cftable_tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY;
+	cftable_tuple.TupleCode = CISTPL_CFTABLE_ENTRY;
+	cftable_tuple.TupleData = &cftuple[2];
+	cftable_tuple.TupleDataLen = cftuple_len - 2;
+	cftable_tuple.TupleDataMax = cftuple_len - 2;
+
+	if (pcmcia_parse_tuple(&cftable_tuple, (cisparse_t *)&cftable_entry))
+		return 0;
+
+#ifdef DEBUG
+	pr_info("IO flags: %x\n", cftable_entry.io.flags);
+#endif
+
+	if (cftable_entry.io.flags & CISTPL_IO_16BIT)
+		return 1;
+
+	return 0;
+}
+#endif
+
 MODULE_LICENSE("GPL");
-- 
2.17.1

Re: [PATCH v8 0/3] Add APNE PCMCIA 100 Mbit support

[Michael Schmitz]

Ignore the earlier ping - this one's the correct one.

Is there anything that I can do to help move this series along?

Cheers,

	Michael

On 28/09/21 19:57, Michael Schmitz wrote:
> The first patch enables the use of core PCMCIA code to parse
> config table entries in Amiga drivers. The remaining two patches
> add 16 bit IO support to the m68k low-level IO access code, and
> add code to the APNE driver to autoprobe for 16 bit IO on cards
> that support it (the 100 Mbit cards). The core PCMCIA config
> table parser is utilized for this (may be built as a module).
>
> Tested by Alex on a 100 Mbit card. Not yet tested on 10 Mbit
> cards - if any of those also have the 16 bit IO feature set
> in their config table, this patch series would break on those
> cards.
>
> Note that only patch 3 has been sent to netdev. Please CC
> linux-m68k when providing comments.
>
> Cheers,
>
>    Michael
>
>

[PATCH v8 0/3] Add APNE PCMCIA 100 Mbit support

[Michael Schmitz]

The first patch enables the use of core PCMCIA code to parse
config table entries in Amiga drivers. The remaining two patches
add 16 bit IO support to the m68k low-level IO access code, and 
add code to the APNE driver to autoprobe for 16 bit IO on cards
that support it (the 100 Mbit cards). The core PCMCIA config
table parser is utilized for this (may be built as a module).

Tested by Alex on a 100 Mbit card. Not yet tested on 10 Mbit
cards - if any of those also have the 16 bit IO feature set
in their config table, this patch series would break on those
cards. 

Note that only patch 3 has been sent to netdev. Please CC
linux-m68k when providing comments.

Cheers,

   Michael