* [PATCH 0/7] Support for some TQMa8M* boards
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This patch set adds support for the following modules:
* TQMa8Mx
* TQMa8MxML
* TQMa8MxNL
Each of the modules is available with different i.MX8M variants, the
bootloader modifies the device tree and disabled paripherals which
are not available on the actual hardware.
All of them can be attached to the same mainboard MBa8Mx, although
TQMa8MxML & TQMa8MxNL need an adapter. For that reason there is a single
mainboard .dtsi file named mba8mx.dtsi.
There is a .dtsi file for each module named imx8m?-tmqa8m*.dts.
Finally there is the final .dts file which includes the mainboard and
the attached module and contains the missing connection, prominently clk
and pinctrl defines.
Alexander Stein (7):
dt-bindings: arm: fsl: add TQMa8MxML boards
arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx
dt-bindings: arm: fsl: add TQMa8MxNL boards
arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
dt-bindings: arm: fsl: add TQMa8Mx boards
arm64: dts: freescale: add initial tree for TQMa8Mx with i.MX8M
.../devicetree/bindings/arm/fsl.yaml | 31 ++
arch/arm64/boot/dts/freescale/Makefile | 3 +
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++
.../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 +++++++++++++++
.../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++
.../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 +++++++++++++++
.../dts/freescale/imx8mq-tqma8mq-mba8mx.dts | 416 ++++++++++++++++++
.../boot/dts/freescale/imx8mq-tqma8mq.dtsi | 369 ++++++++++++++++
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++
arch/arm64/configs/defconfig | 5 +
10 files changed, 2346 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 0/7] Support for some TQMa8M* boards
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This patch set adds support for the following modules:
* TQMa8Mx
* TQMa8MxML
* TQMa8MxNL
Each of the modules is available with different i.MX8M variants, the
bootloader modifies the device tree and disabled paripherals which
are not available on the actual hardware.
All of them can be attached to the same mainboard MBa8Mx, although
TQMa8MxML & TQMa8MxNL need an adapter. For that reason there is a single
mainboard .dtsi file named mba8mx.dtsi.
There is a .dtsi file for each module named imx8m?-tmqa8m*.dts.
Finally there is the final .dts file which includes the mainboard and
the attached module and contains the missing connection, prominently clk
and pinctrl defines.
Alexander Stein (7):
dt-bindings: arm: fsl: add TQMa8MxML boards
arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx
dt-bindings: arm: fsl: add TQMa8MxNL boards
arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
dt-bindings: arm: fsl: add TQMa8Mx boards
arm64: dts: freescale: add initial tree for TQMa8Mx with i.MX8M
.../devicetree/bindings/arm/fsl.yaml | 31 ++
arch/arm64/boot/dts/freescale/Makefile | 3 +
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++
.../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 +++++++++++++++
.../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++
.../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 +++++++++++++++
.../dts/freescale/imx8mq-tqma8mq-mba8mx.dts | 416 ++++++++++++++++++
.../boot/dts/freescale/imx8mq-tqma8mq.dtsi | 369 ++++++++++++++++
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++
arch/arm64/configs/defconfig | 5 +
10 files changed, 2346 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* [PATCH 1/7] dt-bindings: arm: fsl: add TQMa8MxML boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8MxML is a SOM family using NXP i.MX8MM[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mm-<SOM>" for the module and
"tq,imx8mm-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 60f4862ba15e..42de579724bf 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -742,6 +742,17 @@ properties:
- const: variscite,var-som-mx8mm
- const: fsl,imx8mm
+ - description:
+ TQMa8MxML is a series of SOM featuring NXP i.MX8MM system-on-chip
+ variants. It is designed to be soldered on different carrier boards.
+ All variants (TQMa8M[Q,D,S][L]ML) use the same device tree, hence only
+ one compatible is needed.
+ items:
+ - enum:
+ - tq,imx8mm-tqma8mqml-mba8mx # TQ-Systems GmbH i.MX8MM TQMa8MQML SOM on MBa8Mx
+ - const: tq,imx8mm-tqma8mqml # TQ-Systems GmbH i.MX8MM TQMa8MQML SOM
+ - const: fsl,imx8mm
+
- description: i.MX8MN based Boards
items:
- enum:
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 1/7] dt-bindings: arm: fsl: add TQMa8MxML boards
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8MxML is a SOM family using NXP i.MX8MM[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mm-<SOM>" for the module and
"tq,imx8mm-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 60f4862ba15e..42de579724bf 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -742,6 +742,17 @@ properties:
- const: variscite,var-som-mx8mm
- const: fsl,imx8mm
+ - description:
+ TQMa8MxML is a series of SOM featuring NXP i.MX8MM system-on-chip
+ variants. It is designed to be soldered on different carrier boards.
+ All variants (TQMa8M[Q,D,S][L]ML) use the same device tree, hence only
+ one compatible is needed.
+ items:
+ - enum:
+ - tq,imx8mm-tqma8mqml-mba8mx # TQ-Systems GmbH i.MX8MM TQMa8MQML SOM on MBa8Mx
+ - const: tq,imx8mm-tqma8mqml # TQ-Systems GmbH i.MX8MM TQMa8MQML SOM
+ - const: fsl,imx8mm
+
- description: i.MX8MN based Boards
items:
- enum:
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8MQML module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++++
.../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 ++++++++++++++++++
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++++
4 files changed, 895 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..032588e83f12 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
new file mode 100644
index 000000000000..a0e22bef188e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
+ compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc1;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+};
+
+&i2c1 {
+ expander2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+ <&clk IMX8MM_AUDIO_PLL2_OUT>;
+};
+
+&uart1 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&uart2 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006
+ MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006
+ >;
+ };
+
+ pinctrl_expander: expandergrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
+ MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
+ MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004
+ MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004
+ MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
+ MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
+ MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
+ MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
+ MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
+ MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
+ MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
+ MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
+ MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 000000000000..5d947ca7b1bc
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+ compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ /* identical to buck4_reg, but should never change */
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM / VPU */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
+ MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004
+ MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
new file mode 100644
index 000000000000..5b46ab79f05d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/* TQ-Systems GmbH MBa8Mx baseboard */
+
+/ {
+ beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm4 0 250000 0>;
+ beeper-hz = <4000>;
+ amp-supply = <®_vcc_3v3>;
+ };
+
+ chosen {
+ bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
+ stdout-path = &uart3;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiobutton>;
+ autorepeat;
+
+ switch1 {
+ label = "switch1";
+ linux,code = <BTN_0>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ btn2: switch2 {
+ label = "switch2";
+ linux,code = <BTN_1>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ switch3 {
+ label = "switch3";
+ linux,code = <BTN_2>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ gpio_leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioled>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2: led2 {
+ label = "led2";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_hub_vbus: regulator-hub-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_HUB_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "SN65DSI83_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vcc_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "tqm-tlv320aic32";
+ ssi-controller = <&sai3>;
+ audio-codec = <&codec>;
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vcc_3v3>;
+ fsl,magic-packet;
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@e {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0xe>;
+ interrupt-parent = <&expander2>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,dp83867-rxctrl-strap-quirk;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ enet-phy-lane-no-swap;
+ reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <500000>;
+ reset-deassert-us = <500>;
+ };
+ };
+};
+
+&i2c1 {
+ expander0: gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ sd-mux-oe-hog {
+ gpio-hog;
+ gpios = <8 0>;
+ output-low;
+ line-name = "SD_MUX_EN#";
+ };
+
+ boot-cfg-oe-hog {
+ gpio-hog;
+ gpios = <12 0>;
+ output-high;
+ line-name = "BOOT_CFG_OE#";
+ };
+
+ rst-usb-hub-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ output-high;
+ line-name = "RST_USB_HUB#";
+ };
+ };
+
+ expander1: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ codec: tlv320aic3x04@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
+ iov-supply = <®_vcc_3v3>;
+ ldoin-supply = <®_vcc_3v3>;
+ };
+
+ sensor1: sensor@1f {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1f>;
+ };
+
+ eeprom3: eeprom@57 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ #sound-dai-cells = <0>;
+ assigned-clock-rates = <49152000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+/* console */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+/* UART4 is assigned to Cortex-M4 */
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-mmc;
+ no-sdio;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8MQML module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++++
.../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 ++++++++++++++++++
arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++++
4 files changed, 895 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index db9e36ebe932..032588e83f12 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
new file mode 100644
index 000000000000..a0e22bef188e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
+ compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc1;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+};
+
+&i2c1 {
+ expander2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+ <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+ <&clk IMX8MM_AUDIO_PLL2_OUT>;
+};
+
+&uart1 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&uart2 {
+ assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006
+ MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006
+ MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006
+ MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006
+ MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006
+ MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006
+ MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006
+ >;
+ };
+
+ pinctrl_expander: expandergrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
+ MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
+ MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
+ MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
+ MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
+ MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
+ MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
+ MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
+ MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
+ MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
+ MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
+ MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
+ MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
+ MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
+ MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
+ MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
+ MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004
+ MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004
+ MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004
+ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004
+ MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
+ MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
+ MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
+ MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
+ MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
+ MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
+ MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
+ MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
+ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
+ MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
+ MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 000000000000..5d947ca7b1bc
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+ compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ /* identical to buck4_reg, but should never change */
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXML_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM / VPU */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
+ MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
+ MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
+ MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
+ MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004
+ MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004
+ MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
+ MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ /* option USDHC3_RESET_B not defined, only in RM */
+ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
new file mode 100644
index 000000000000..5b46ab79f05d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
@@ -0,0 +1,285 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/* TQ-Systems GmbH MBa8Mx baseboard */
+
+/ {
+ beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm4 0 250000 0>;
+ beeper-hz = <4000>;
+ amp-supply = <®_vcc_3v3>;
+ };
+
+ chosen {
+ bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
+ stdout-path = &uart3;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpiobutton>;
+ autorepeat;
+
+ switch1 {
+ label = "switch1";
+ linux,code = <BTN_0>;
+ gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ btn2: switch2 {
+ label = "switch2";
+ linux,code = <BTN_1>;
+ gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+
+ switch3 {
+ label = "switch3";
+ linux,code = <BTN_2>;
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ wakeup-source;
+ };
+ };
+
+ gpio_leds: gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpioled>;
+
+ led1 {
+ label = "led1";
+ gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2: led2 {
+ label = "led2";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_hub_vbus: regulator-hub-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_HUB_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "SN65DSI83_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vcc_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "MBA8MX_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "tqm-tlv320aic32";
+ ssi-controller = <&sai3>;
+ audio-codec = <&codec>;
+ };
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_vcc_3v3>;
+ fsl,magic-packet;
+ mac-address = [ 00 00 00 00 00 00 ];
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@e {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0xe>;
+ interrupt-parent = <&expander2>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,dp83867-rxctrl-strap-quirk;
+ ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+ enet-phy-lane-no-swap;
+ reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <500000>;
+ reset-deassert-us = <500>;
+ };
+ };
+};
+
+&i2c1 {
+ expander0: gpio@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ sd-mux-oe-hog {
+ gpio-hog;
+ gpios = <8 0>;
+ output-low;
+ line-name = "SD_MUX_EN#";
+ };
+
+ boot-cfg-oe-hog {
+ gpio-hog;
+ gpios = <12 0>;
+ output-high;
+ line-name = "BOOT_CFG_OE#";
+ };
+
+ rst-usb-hub-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ output-high;
+ line-name = "RST_USB_HUB#";
+ };
+ };
+
+ expander1: gpio@24 {
+ compatible = "nxp,pca9555";
+ reg = <0x24>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ codec: tlv320aic3x04@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
+ iov-supply = <®_vcc_3v3>;
+ ldoin-supply = <®_vcc_3v3>;
+ };
+
+ sensor1: sensor@1f {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1f>;
+ };
+
+ eeprom3: eeprom@57 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x57>;
+ pagesize = <16>;
+ };
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>;
+ status = "okay";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>;
+ status = "okay";
+};
+
+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ #sound-dai-cells = <0>;
+ assigned-clock-rates = <49152000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+/* console */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+/* UART4 is assigned to Cortex-M4 */
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ bus-width = <4>;
+ cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-mmc;
+ no-sdio;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 3/7] arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
With the device tree in place, enable missing drivers as modules, if
possible. PHY driver needs built-in for interrupt support.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/configs/defconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 156d96afbbfc..2e5de4456725 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -366,6 +366,7 @@ CONFIG_MICROSEMI_PHY=y
CONFIG_AT803X_PHY=y
CONFIG_REALTEK_PHY=y
CONFIG_ROCKCHIP_PHY=y
+CONFIG_DP83867_PHY=y
CONFIG_VITESSE_PHY=y
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
@@ -399,6 +400,7 @@ CONFIG_TOUCHSCREEN_EDT_FT5X06=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PM8941_PWRKEY=y
CONFIG_INPUT_PM8XXX_VIBRATOR=m
+CONFIG_INPUT_PWM_BEEPER=m
CONFIG_INPUT_PWM_VIBRA=m
CONFIG_INPUT_HISI_POWERKEY=y
# CONFIG_SERIO_SERPORT is not set
@@ -555,6 +557,7 @@ CONFIG_BATTERY_MAX17042=m
CONFIG_CHARGER_BQ25890=m
CONFIG_CHARGER_BQ25980=m
CONFIG_SENSORS_ARM_SCPI=y
+CONFIG_SENSORS_JC42=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_PWM_FAN=m
CONFIG_SENSORS_RASPBERRYPI_HWMON=m
@@ -784,6 +787,7 @@ CONFIG_SND_SOC_RT5659=m
CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
CONFIG_SND_SOC_SIMPLE_MUX=m
CONFIG_SND_SOC_TAS571X=m
+CONFIG_SND_SOC_TLV320AIC32X4_I2C=m
CONFIG_SND_SOC_WCD934X=m
CONFIG_SND_SOC_WM8904=m
CONFIG_SND_SOC_WM8960=m
@@ -898,6 +902,7 @@ CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_HYM8563=m
CONFIG_RTC_DRV_MAX77686=y
CONFIG_RTC_DRV_RK808=m
+CONFIG_RTC_DRV_PCF85063=m
CONFIG_RTC_DRV_PCF85363=m
CONFIG_RTC_DRV_M41T80=m
CONFIG_RTC_DRV_RX8581=m
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 3/7] arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
With the device tree in place, enable missing drivers as modules, if
possible. PHY driver needs built-in for interrupt support.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/configs/defconfig | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index 156d96afbbfc..2e5de4456725 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -366,6 +366,7 @@ CONFIG_MICROSEMI_PHY=y
CONFIG_AT803X_PHY=y
CONFIG_REALTEK_PHY=y
CONFIG_ROCKCHIP_PHY=y
+CONFIG_DP83867_PHY=y
CONFIG_VITESSE_PHY=y
CONFIG_USB_PEGASUS=m
CONFIG_USB_RTL8150=m
@@ -399,6 +400,7 @@ CONFIG_TOUCHSCREEN_EDT_FT5X06=m
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PM8941_PWRKEY=y
CONFIG_INPUT_PM8XXX_VIBRATOR=m
+CONFIG_INPUT_PWM_BEEPER=m
CONFIG_INPUT_PWM_VIBRA=m
CONFIG_INPUT_HISI_POWERKEY=y
# CONFIG_SERIO_SERPORT is not set
@@ -555,6 +557,7 @@ CONFIG_BATTERY_MAX17042=m
CONFIG_CHARGER_BQ25890=m
CONFIG_CHARGER_BQ25980=m
CONFIG_SENSORS_ARM_SCPI=y
+CONFIG_SENSORS_JC42=m
CONFIG_SENSORS_LM90=m
CONFIG_SENSORS_PWM_FAN=m
CONFIG_SENSORS_RASPBERRYPI_HWMON=m
@@ -784,6 +787,7 @@ CONFIG_SND_SOC_RT5659=m
CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
CONFIG_SND_SOC_SIMPLE_MUX=m
CONFIG_SND_SOC_TAS571X=m
+CONFIG_SND_SOC_TLV320AIC32X4_I2C=m
CONFIG_SND_SOC_WCD934X=m
CONFIG_SND_SOC_WM8904=m
CONFIG_SND_SOC_WM8960=m
@@ -898,6 +902,7 @@ CONFIG_RTC_DRV_DS1307=m
CONFIG_RTC_DRV_HYM8563=m
CONFIG_RTC_DRV_MAX77686=y
CONFIG_RTC_DRV_RK808=m
+CONFIG_RTC_DRV_PCF85063=m
CONFIG_RTC_DRV_PCF85363=m
CONFIG_RTC_DRV_M41T80=m
CONFIG_RTC_DRV_RX8581=m
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 4/7] dt-bindings: arm: fsl: add TQMa8MxNL boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8MxNL is a SOM family using NXP i.MX8MN[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mn-<SOM>" for the module and
"tq,imx8mn-<SOM>-<SBC>" for mainboards
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 42de579724bf..ed6f090df397 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -768,6 +768,17 @@ properties:
- const: variscite,var-som-mx8mn
- const: fsl,imx8mn
+ - description:
+ TQMa8MxNL is a series of SOM featuring NXP i.MX8MN system-on-chip
+ variants. It is designed to be soldered on different carrier boards.
+ All variants (TQMa8M[Q,D,S][L]NL) use the same device tree, hence only
+ one compatible is needed.
+ items:
+ - enum:
+ - tq,imx8mn-tqma8mqnl-mba8mx # TQ-Systems GmbH i.MX8MN TQMa8MQNL SOM on MBa8Mx
+ - const: tq,imx8mn-tqma8mqnl # TQ-Systems GmbH i.MX8MN TQMa8MQNL SOM
+ - const: fsl,imx8mn
+
- description: i.MX8MP based Boards
items:
- enum:
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 4/7] dt-bindings: arm: fsl: add TQMa8MxNL boards
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8MxNL is a SOM family using NXP i.MX8MN[Q,QL,DL,S,SL] CPU
MBa8Mx is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mn-<SOM>" for the module and
"tq,imx8mn-<SOM>-<SBC>" for mainboards
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 42de579724bf..ed6f090df397 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -768,6 +768,17 @@ properties:
- const: variscite,var-som-mx8mn
- const: fsl,imx8mn
+ - description:
+ TQMa8MxNL is a series of SOM featuring NXP i.MX8MN system-on-chip
+ variants. It is designed to be soldered on different carrier boards.
+ All variants (TQMa8M[Q,D,S][L]NL) use the same device tree, hence only
+ one compatible is needed.
+ items:
+ - enum:
+ - tq,imx8mn-tqma8mqnl-mba8mx # TQ-Systems GmbH i.MX8MN TQMa8MQNL SOM on MBa8Mx
+ - const: tq,imx8mn-tqma8mqnl # TQ-Systems GmbH i.MX8MN TQMa8MQNL SOM
+ - const: fsl,imx8mn
+
- description: i.MX8MP based Boards
items:
- enum:
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 5/7] arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8MQNL module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++++
.../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 ++++++++++++++++++
3 files changed, 629 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 032588e83f12..ed166e6d20f6 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
new file mode 100644
index 000000000000..3733f79b29cf
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn-tqma8mqnl.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
+ compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc1;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
+};
+
+/* Located on TQMa8MxML-ADAP */
+&gpio2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0hub_sel>;
+
+ sel-usb-hub-hog {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
+&i2c1 {
+ expander2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
+ <&clk IMX8MN_AUDIO_PLL2_OUT>;
+};
+
+&usbotg1 {
+ dr_mode = "host";
+ disable-over-current;
+ power-active-high;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000146
+ MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000146
+ MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000146
+ MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000146
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000146
+ MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000146
+ MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000146
+ MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000146
+ >;
+ };
+
+ pinctrl_expander2: expander2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
+ MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
+ MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
+ MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
+ MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
+ MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
+ MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
+ MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
+ MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
+ MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
+ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
+ MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
+ MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
+ MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
+ MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
+ MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
+ MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001C4
+ MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001C4
+ MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001C4
+ MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001C4
+ MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001C4
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
+ MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
+ MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
+ MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
+ MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
+ MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
+ MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
+ MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
+ MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
+ MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
+ MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_usb0hub_sel: usb0hub_sel {
+ fsl,pins = <
+ /* SEL_USB_HUB_B */
+ MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x84
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84
+ MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84
+ MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x1C4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
new file mode 100644
index 000000000000..ab474529d66f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mn.dtsi"
+
+/ {
+ model = "TQ-Systems i.MX8MN TQMa8MxNL";
+ compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXNL_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXNL_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 .. 0.95 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84
+ MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84
+ MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84
+ MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84
+ MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84
+ MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4
+ MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4
+ MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 5/7] arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8MQNL module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++++
.../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 ++++++++++++++++++
3 files changed, 629 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 032588e83f12..ed166e6d20f6 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
new file mode 100644
index 000000000000..3733f79b29cf
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn-tqma8mqnl.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
+ compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc3;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc1;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ startup-delay-us = <100>;
+ off-on-delay-us = <12000>;
+ };
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
+};
+
+/* Located on TQMa8MxML-ADAP */
+&gpio2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb0hub_sel>;
+
+ sel-usb-hub-hog {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+};
+
+&i2c1 {
+ expander2: gpio@27 {
+ compatible = "nxp,pca9555";
+ reg = <0x27>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
+ <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
+ <&clk IMX8MN_AUDIO_PLL2_OUT>;
+};
+
+&usbotg1 {
+ dr_mode = "host";
+ disable-over-current;
+ power-active-high;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000146
+ MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000146
+ MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000146
+ MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000146
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000146
+ MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000146
+ MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000146
+ MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000146
+ >;
+ };
+
+ pinctrl_expander2: expander2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
+ MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
+ MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
+ MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
+ MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
+ MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
+ MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
+ MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
+ MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
+ MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
+ MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
+ MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
+ MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
+ MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
+ MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
+ MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
+ MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001C4
+ MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001C4
+ MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001C4
+ MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001C4
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001C4
+ MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001C4
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
+ MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
+ MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
+ MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
+ MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
+ MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
+ MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
+ MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
+ MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
+ MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
+ MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
+ >;
+ };
+
+ pinctrl_usb0hub_sel: usb0hub_sel {
+ fsl,pins = <
+ /* SEL_USB_HUB_B */
+ MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x84
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84
+ MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84
+ MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x1C4
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
+ MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
+ MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
+ MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
+ MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
+ MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
+ MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
new file mode 100644
index 000000000000..ab474529d66f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
@@ -0,0 +1,345 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mn.dtsi"
+
+/ {
+ model = "TQ-Systems i.MX8MN TQMa8MxNL";
+ compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXNL_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MXNL_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pca9450: pmic@25 {
+ compatible = "nxp,pca9450a";
+ reg = <0x25>;
+
+ /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+ pinctrl-0 = <&pinctrl_pmic>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio1>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ /* V_0V85_SOC: 0.85 .. 0.95 */
+ buck1_reg: BUCK1 {
+ regulator-name = "BUCK1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VDD_ARM */
+ buck2_reg: BUCK2 {
+ regulator-name = "BUCK2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ nxp,dvs-run-voltage = <950000>;
+ nxp,dvs-standby-voltage = <850000>;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
+ buck3_reg: BUCK3 {
+ regulator-name = "BUCK3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <950000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <3125>;
+ };
+
+ /* VCC3V3 -> VMMC, ... must not be changed */
+ buck4_reg: BUCK4 {
+ regulator-name = "BUCK4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+ buck5_reg: BUCK5 {
+ regulator-name = "BUCK5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V1 -> RAM, ... must not be changed */
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_SNVS */
+ ldo1_reg: LDO1 {
+ regulator-name = "LDO1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V8_SNVS */
+ ldo2_reg: LDO2 {
+ regulator-name = "LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_1V8_ANA */
+ ldo3_reg: LDO3 {
+ regulator-name = "LDO3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* V_0V9_MIPI */
+ ldo4_reg: LDO4 {
+ regulator-name = "LDO4";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ /* VCC SD IO - switched using SD2 VSELECT */
+ ldo5_reg: LDO5 {
+ regulator-name = "LDO5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ read-only;
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_flexspi: flexspigrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84
+ MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84
+ MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84
+ MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84
+ MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84
+ MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4
+ MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4
+ MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4
+ >;
+ };
+
+ pinctrl_pmic: pmicgrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
+ MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
+ MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
+ MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
+ MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
+ MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
+ MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
+ MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
+ MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
+ MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
+ MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
+ MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 6/7] dt-bindings: arm: fsl: add TQMa8Mx boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8Mx is a SOM family using NXP i.MX8M[Q,QL, D] CPU
MBa8Mx is a evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mq-<SOM>" for the module and
"tq,imx8mq-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index ed6f090df397..18034b23ca08 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -815,6 +815,15 @@ properties:
- const: purism,librem5
- const: fsl,imx8mq
+ - description:
+ TQMa8Mx is a series of SOM featuring NXP i.MX8MQ system-on-chip
+ variants. It is designed to be clicked on different carrier boards.
+ items:
+ - enum:
+ - tq,imx8mq-tqma8mq-mba8mx # TQ-Systems GmbH i.MX8MQ TQMa8Mx SOM on MBa8Mx
+ - const: tq,imx8mq-tqma8mq # TQ-Systems GmbH i.MX8MQ TQMa8Mx SOM
+ - const: fsl,imx8mq
+
- description: Zodiac Inflight Innovations Ultra Boards
items:
- enum:
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 6/7] dt-bindings: arm: fsl: add TQMa8Mx boards
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
TQMa8Mx is a SOM family using NXP i.MX8M[Q,QL, D] CPU
MBa8Mx is a evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mq-<SOM>" for the module and
"tq,imx8mq-<SOM>-<SBC>" for the module on that mainboard
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index ed6f090df397..18034b23ca08 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -815,6 +815,15 @@ properties:
- const: purism,librem5
- const: fsl,imx8mq
+ - description:
+ TQMa8Mx is a series of SOM featuring NXP i.MX8MQ system-on-chip
+ variants. It is designed to be clicked on different carrier boards.
+ items:
+ - enum:
+ - tq,imx8mq-tqma8mq-mba8mx # TQ-Systems GmbH i.MX8MQ TQMa8Mx SOM on MBa8Mx
+ - const: tq,imx8mq-tqma8mq # TQ-Systems GmbH i.MX8MQ TQMa8Mx SOM
+ - const: fsl,imx8mq
+
- description: Zodiac Inflight Innovations Ultra Boards
items:
- enum:
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 7/7] arm64: dts: freescale: add initial tree for TQMa8Mx with i.MX8M
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-06 13:23 ` Alexander Stein
-1 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8Mx module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mq-tqma8mq-mba8mx.dts | 416 ++++++++++++++++++
.../boot/dts/freescale/imx8mq-tqma8mq.dtsi | 369 ++++++++++++++++
3 files changed, 786 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index ed166e6d20f6..7776bb6aeee9 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-tqma8mq-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-mnt-reform2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
new file mode 100644
index 000000000000..d105969fddbb
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mq-tqma8mq.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ on MBa8Mx";
+ compatible = "tq,imx8mq-tqma8mq-mba8mx", "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ extcon_usbotg: extcon-usbotg0 {
+ compatible = "linux,extcon-usb-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbcon0>;
+ id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pcie0_refclk: pcie0-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ pcie1_refclk: pcie1-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ reg_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regotgvbus>;
+ regulator-name = "MBA8MQ_OTG_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&btn2 {
+ gpios = <&gpio3 17 GPIO_ACTIVE_LOW>;
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MQ_CLK_SAI3_ROOT>;
+};
+
+&i2c1 {
+ expander2: gpio@25 {
+ compatible = "nxp,pca9555";
+ reg = <0x25>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ mpcie-rst-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ output-high;
+ line-name = "MPCIE_RST#";
+ };
+ };
+};
+
+&irqsteer {
+ status = "okay";
+};
+
+&gpio_leds {
+ led3 {
+ label = "led3";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&led2 {
+ gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0 {
+ reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE1_AUX>,
+ <&clk IMX8MQ_CLK_PCIE1_PHY>,
+ <&pcie0_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ epdev_on-supply = <®_vcc_3v3>;
+ hard-wired = <1>;
+ status = "okay";
+};
+
+/*
+ * miniPCIe, also usable for cards with USB. Therefore configure the reset as
+ * static gpio hog.
+ */
+&pcie1 {
+ clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE2_AUX>,
+ <&clk IMX8MQ_CLK_PCIE2_PHY>,
+ <&pcie1_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ epdev_on-supply = <®_vcc_3v3>;
+ hard-wired = <1>;
+ status = "okay";
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MQ_CLK_SAI3_IPG>, <&clk IMX8MQ_CLK_DUMMY>,
+ <&clk IMX8MQ_CLK_SAI3_ROOT>, <&clk IMX8MQ_CLK_DUMMY>,
+ <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_AUDIO_PLL1_OUT>,
+ <&clk IMX8MQ_AUDIO_PLL2_OUT>;
+};
+
+&uart1 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+&uart2 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+/* console */
+&uart3 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+ assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+};
+
+&usb3_phy0 {
+ vbus-supply = <®_otg_vbus>;
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ /* we implement dual role but not full featured OTG */
+ extcon = <&extcon_usbotg>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ /*
+ * TODO: OC not supported due to non matching active polarity
+ * pinctrl-names = "default";
+ * pinctrl-0 = <&pinctrl_usb0>;
+ */
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&vpu {
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x0000004e
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x0000004e
+ >;
+ };
+
+ pinctrl_expander: expandergrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0xd6
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x41
+ MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x41
+ MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x41
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x41
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41
+ MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000067
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000067
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000067
+ MX8MQ_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000067
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000067
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000067
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000067
+ MX8MQ_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000067
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO14_PWM3_OUT 0x16
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO15_PWM4_OUT 0x16
+ >;
+ };
+
+ pinctrl_regotgvbus: reggotgvbusgrp {
+ fsl,pins = <
+ /* USB1 OTG PWR as GPIO */
+ MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x06
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0xc1
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6
+ MX8MQ_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX 0x79
+ >;
+ };
+
+ /*
+ * TODO: OC detection is not functional yet since signal is expected to
+ * be low active. HW on MBa8Mx has high active signalling
+ * See: https://community.nxp.com/message/1247228?commentID=1247228#comment-1247228
+ */
+ pinctrl_usb0: usb0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x01
+ >;
+ };
+
+ pinctrl_usbcon0: usb0congrp {
+ fsl,pins = <
+ /* ID: floating / high: device, low: host -> use PU */
+ MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xe6
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
new file mode 100644
index 000000000000..d7efdb9f9c1a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
@@ -0,0 +1,369 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ";
+ compatible = "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MX_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MX_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vdd_arm: regulator-vdd-arm {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dvfs>;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "TQMa8Mx_DVFS";
+ regulator-type = "voltage";
+ regulator-settling-time-us = <150000>;
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ states = <900000 0x1 1000000 0x0>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_1 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_2 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_3 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pfuze100: pmic@8 {
+ compatible = "fsl,pfuze100";
+ fsl,pfuze-support-disable-sw;
+ reg = <0x8>;
+
+ regulators {
+ /* VDD_GPU */
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ /* VDD_VPU */
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ /* NVCC_DRAM */
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ /* VDD_DRAM */
+ sw3a_reg: sw3ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ /* 1.8 V for QSPI NOR, e-MMC IO, must not be changed */
+ nvcc_1v8_reg: sw4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-always-on;
+ };
+
+ /* not used */
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ /* VDD_PHY_0V9 */
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <975000>;
+ regulator-always-on;
+ };
+
+ /* VDD_PHY_1V8 */
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1675000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ /* VDDA_1V8 */
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1625000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ /* VDD_PHY_3V3 */
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3625000>;
+ regulator-always-on;
+ };
+
+ /* not used */
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupt-names = "irq";
+ interrupt-parent = <&gpio1>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ read-only;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&pcie0 {
+ /* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+ vph-supply = <&vgen5_reg>;
+};
+
+&pcie1 {
+ /* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+ vph-supply = <&vgen5_reg>;
+};
+
+&qspi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ assigned-clocks = <&clk IMX8MQ_CLK_QSPI>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/* Attention: wdog reset forcing POR needs baseboard support */
+&wdog1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_dvfs: dvfsgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x16
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000074
+ MX8MQ_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000074
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x97
+ MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x97
+ MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x97
+ MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x97
+ MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x97
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x41
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 26+ messages in thread
* [PATCH 7/7] arm64: dts: freescale: add initial tree for TQMa8Mx with i.MX8M
@ 2021-10-06 13:23 ` Alexander Stein
0 siblings, 0 replies; 26+ messages in thread
From: Alexander Stein @ 2021-10-06 13:23 UTC (permalink / raw)
To: Rob Herring, Shawn Guo, Sascha Hauer, Catalin Marinas, Will Deacon
Cc: Alexander Stein, Pengutronix Kernel Team, Fabio Estevam,
NXP Linux Team, devicetree, linux-kernel, linux-arm-kernel
This adds support for TQMa8Mx module on MBa8Mx board.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../dts/freescale/imx8mq-tqma8mq-mba8mx.dts | 416 ++++++++++++++++++
.../boot/dts/freescale/imx8mq-tqma8mq.dtsi | 369 ++++++++++++++++
3 files changed, 786 insertions(+)
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index ed166e6d20f6..7776bb6aeee9 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -60,6 +60,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-tqma8mq-mba8mx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-mnt-reform2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
new file mode 100644
index 000000000000..d105969fddbb
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
@@ -0,0 +1,416 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mq-tqma8mq.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ on MBa8Mx";
+ compatible = "tq,imx8mq-tqma8mq-mba8mx", "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+ aliases {
+ eeprom0 = &eeprom3;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ rtc0 = &pcf85063;
+ rtc1 = &snvs_rtc;
+ };
+
+ extcon_usbotg: extcon-usbotg0 {
+ compatible = "linux,extcon-usb-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbcon0>;
+ id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+
+ pcie0_refclk: pcie0-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ pcie1_refclk: pcie1-refclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ };
+
+ reg_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_regotgvbus>;
+ regulator-name = "MBA8MQ_OTG_VBUS";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usdhc2_vmmc: regulator-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&btn2 {
+ gpios = <&gpio3 17 GPIO_ACTIVE_LOW>;
+};
+
+&codec {
+ clock-names = "mclk";
+ clocks = <&clk IMX8MQ_CLK_SAI3_ROOT>;
+};
+
+&i2c1 {
+ expander2: gpio@25 {
+ compatible = "nxp,pca9555";
+ reg = <0x25>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ vcc-supply = <®_vcc_3v3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ mpcie-rst-hog {
+ gpio-hog;
+ gpios = <13 0>;
+ output-high;
+ line-name = "MPCIE_RST#";
+ };
+ };
+};
+
+&irqsteer {
+ status = "okay";
+};
+
+&gpio_leds {
+ led3 {
+ label = "led3";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&led2 {
+ gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0 {
+ reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
+ clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE1_AUX>,
+ <&clk IMX8MQ_CLK_PCIE1_PHY>,
+ <&pcie0_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ epdev_on-supply = <®_vcc_3v3>;
+ hard-wired = <1>;
+ status = "okay";
+};
+
+/*
+ * miniPCIe, also usable for cards with USB. Therefore configure the reset as
+ * static gpio hog.
+ */
+&pcie1 {
+ clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+ <&clk IMX8MQ_CLK_PCIE2_AUX>,
+ <&clk IMX8MQ_CLK_PCIE2_PHY>,
+ <&pcie1_refclk>;
+ clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+ epdev_on-supply = <®_vcc_3v3>;
+ hard-wired = <1>;
+ status = "okay";
+};
+
+&sai3 {
+ assigned-clocks = <&clk IMX8MQ_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+ clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+ clocks = <&clk IMX8MQ_CLK_SAI3_IPG>, <&clk IMX8MQ_CLK_DUMMY>,
+ <&clk IMX8MQ_CLK_SAI3_ROOT>, <&clk IMX8MQ_CLK_DUMMY>,
+ <&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_AUDIO_PLL1_OUT>,
+ <&clk IMX8MQ_AUDIO_PLL2_OUT>;
+};
+
+&uart1 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+&uart2 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+/* console */
+&uart3 {
+ assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+ assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+};
+
+&usb3_phy0 {
+ vbus-supply = <®_otg_vbus>;
+ status = "okay";
+};
+
+&usb_dwc3_0 {
+ /* we implement dual role but not full featured OTG */
+ extcon = <&extcon_usbotg>;
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ /*
+ * TODO: OC not supported due to non matching active polarity
+ * pinctrl-names = "default";
+ * pinctrl-0 = <&pinctrl_usb0>;
+ */
+ disable-over-current;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb3_phy1 {
+ status = "okay";
+};
+
+&usb_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&vpu {
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x0000004e
+ MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x0000004e
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x0000004e
+ MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x0000004e
+ >;
+ };
+
+ pinctrl_expander: expandergrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0xd6
+ >;
+ };
+
+ pinctrl_fec1: fec1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3
+ MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23
+ MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
+ MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
+ MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
+ MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
+ MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
+ MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
+ MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
+ MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
+ MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
+ MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
+ MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
+ MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
+ >;
+ };
+
+ pinctrl_gpiobutton: gpiobuttongrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x41
+ MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x41
+ MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x41
+ >;
+ };
+
+ pinctrl_gpioled: gpioledgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x41
+ MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41
+ MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x41
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000067
+ MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000067
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000067
+ MX8MQ_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000067
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000067
+ MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000067
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000067
+ MX8MQ_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000067
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO14_PWM3_OUT 0x16
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO15_PWM4_OUT 0x16
+ >;
+ };
+
+ pinctrl_regotgvbus: reggotgvbusgrp {
+ fsl,pins = <
+ /* USB1 OTG PWR as GPIO */
+ MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x06
+ >;
+ };
+
+ pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0xc1
+ >;
+ };
+
+ pinctrl_sai3: sai3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6
+ MX8MQ_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0xd6
+ MX8MQ_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6
+ MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6
+ MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x79
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX 0x79
+ MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX 0x79
+ >;
+ };
+
+ /*
+ * TODO: OC detection is not functional yet since signal is expected to
+ * be low active. HW on MBa8Mx has high active signalling
+ * See: https://community.nxp.com/message/1247228?commentID=1247228#comment-1247228
+ */
+ pinctrl_usb0: usb0grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x01
+ >;
+ };
+
+ pinctrl_usbcon0: usb0congrp {
+ fsl,pins = <
+ /* ID: floating / high: device, low: host -> use PU */
+ MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10 0xe6
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x85
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc5
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc5
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc5
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc5
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc5
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f
+ MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc7
+ MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc7
+ MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc7
+ MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc7
+ MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc7
+ MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1
+ >;
+ };
+
+ pinctrl_usdhc2_gpio: usdhc2grpgpio {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41
+ >;
+ };
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
new file mode 100644
index 000000000000..d7efdb9f9c1a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
@@ -0,0 +1,369 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+ model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ";
+ compatible = "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+ chosen {
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* our minimum RAM config will be 1024 MiB */
+ reg = <0x00000000 0x40000000 0 0x40000000>;
+ };
+
+ /* e-MMC IO, needed for HS modes */
+ reg_vcc1v8: regulator-vcc1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MX_VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ reg_vcc3v3: regulator-vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "TQMA8MX_VCC3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vdd_arm: regulator-vdd-arm {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_dvfs>;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-name = "TQMa8Mx_DVFS";
+ regulator-type = "voltage";
+ regulator-settling-time-us = <150000>;
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ states = <900000 0x1 1000000 0x0>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* global autoconfigured region for contiguous allocations */
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ /* 640 MiB */
+ size = <0 0x28000000>;
+ /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+ alloc-ranges = <0 0x40000000 0 0x78000000>;
+ linux,cma-default;
+ };
+ };
+};
+
+&A53_0 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_1 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_2 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&A53_3 {
+ cpu-supply = <®_vdd_arm>;
+};
+
+&pgc_gpu {
+ power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+ power-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pfuze100: pmic@8 {
+ compatible = "fsl,pfuze100";
+ fsl,pfuze-support-disable-sw;
+ reg = <0x8>;
+
+ regulators {
+ /* VDD_GPU */
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ /* VDD_VPU */
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ /* NVCC_DRAM */
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ /* VDD_DRAM */
+ sw3a_reg: sw3ab {
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ /* 1.8 V for QSPI NOR, e-MMC IO, must not be changed */
+ nvcc_1v8_reg: sw4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-always-on;
+ };
+
+ /* not used */
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ /* VDD_PHY_0V9 */
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <975000>;
+ regulator-always-on;
+ };
+
+ /* VDD_PHY_1V8 */
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1675000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-always-on;
+ };
+
+ /* VDDA_1V8 */
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1625000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-always-on;
+ };
+
+ /* VDD_PHY_3V3 */
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3625000>;
+ regulator-always-on;
+ };
+
+ /* not used */
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ };
+ };
+
+ sensor0: temperature-sensor-eeprom@1b {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1b>;
+ };
+
+ pcf85063: rtc@51 {
+ compatible = "nxp,pcf85063a";
+ reg = <0x51>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rtc>;
+ interrupt-names = "irq";
+ interrupt-parent = <&gpio1>;
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+ quartz-load-femtofarads = <7000>;
+ };
+
+ eeprom1: eeprom@53 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ read-only;
+ };
+
+ eeprom0: eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ pagesize = <32>;
+ };
+};
+
+&pcie0 {
+ /* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+ vph-supply = <&vgen5_reg>;
+};
+
+&pcie1 {
+ /* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+ vph-supply = <&vgen5_reg>;
+};
+
+&qspi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ assigned-clocks = <&clk IMX8MQ_CLK_QSPI>;
+ assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>;
+ status = "okay";
+
+ flash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <84000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ no-sd;
+ no-sdio;
+ vmmc-supply = <®_vcc3v3>;
+ vqmmc-supply = <®_vcc1v8>;
+ status = "okay";
+};
+
+/* Attention: wdog reset forcing POR needs baseboard support */
+&wdog1 {
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_dvfs: dvfsgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x16
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f
+ MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000074
+ MX8MQ_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000074
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x97
+ MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
+ MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x97
+ MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x97
+ MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x97
+ MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x97
+ >;
+ };
+
+ pinctrl_rtc: rtcgrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1 0x41
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x85
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc5
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc5
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc5
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc5
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc5
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc5
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc5
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc5
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc5
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x85
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x87
+ MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc7
+ MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc7
+ MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc7
+ MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc7
+ MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc7
+ MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc7
+ MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc7
+ MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc7
+ MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc7
+ MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x87
+ MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 26+ messages in thread
* Re: [PATCH 1/7] dt-bindings: arm: fsl: add TQMa8MxML boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-14 19:55 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:55 UTC (permalink / raw)
To: Alexander Stein
Cc: Will Deacon, Fabio Estevam, Rob Herring, Pengutronix Kernel Team,
devicetree, NXP Linux Team, Shawn Guo, linux-arm-kernel,
Catalin Marinas, linux-kernel, Sascha Hauer
On Wed, 06 Oct 2021 15:23:03 +0200, Alexander Stein wrote:
> TQMa8MxML is a SOM family using NXP i.MX8MM[Q,QL,DL,S,SL] CPU
> MBa8Mx is an evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mm-<SOM>" for the module and
> "tq,imx8mm-<SOM>-<SBC>" for the module on that mainboard
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 1/7] dt-bindings: arm: fsl: add TQMa8MxML boards
@ 2021-10-14 19:55 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:55 UTC (permalink / raw)
To: Alexander Stein
Cc: Will Deacon, Fabio Estevam, Rob Herring, Pengutronix Kernel Team,
devicetree, NXP Linux Team, Shawn Guo, linux-arm-kernel,
Catalin Marinas, linux-kernel, Sascha Hauer
On Wed, 06 Oct 2021 15:23:03 +0200, Alexander Stein wrote:
> TQMa8MxML is a SOM family using NXP i.MX8MM[Q,QL,DL,S,SL] CPU
> MBa8Mx is an evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mm-<SOM>" for the module and
> "tq,imx8mm-<SOM>-<SBC>" for the module on that mainboard
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 4/7] dt-bindings: arm: fsl: add TQMa8MxNL boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-14 19:55 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:55 UTC (permalink / raw)
To: Alexander Stein
Cc: Will Deacon, Fabio Estevam, devicetree, Shawn Guo, linux-kernel,
Sascha Hauer, NXP Linux Team, Pengutronix Kernel Team,
linux-arm-kernel, Catalin Marinas, Rob Herring
On Wed, 06 Oct 2021 15:23:06 +0200, Alexander Stein wrote:
> TQMa8MxNL is a SOM family using NXP i.MX8MN[Q,QL,DL,S,SL] CPU
> MBa8Mx is an evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mn-<SOM>" for the module and
> "tq,imx8mn-<SOM>-<SBC>" for mainboards
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 4/7] dt-bindings: arm: fsl: add TQMa8MxNL boards
@ 2021-10-14 19:55 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:55 UTC (permalink / raw)
To: Alexander Stein
Cc: Will Deacon, Fabio Estevam, devicetree, Shawn Guo, linux-kernel,
Sascha Hauer, NXP Linux Team, Pengutronix Kernel Team,
linux-arm-kernel, Catalin Marinas, Rob Herring
On Wed, 06 Oct 2021 15:23:06 +0200, Alexander Stein wrote:
> TQMa8MxNL is a SOM family using NXP i.MX8MN[Q,QL,DL,S,SL] CPU
> MBa8Mx is an evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mn-<SOM>" for the module and
> "tq,imx8mn-<SOM>-<SBC>" for mainboards
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 11 +++++++++++
> 1 file changed, 11 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 6/7] dt-bindings: arm: fsl: add TQMa8Mx boards
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-14 19:56 ` Rob Herring
-1 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:56 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Shawn Guo, linux-kernel, devicetree,
Catalin Marinas, Will Deacon, NXP Linux Team, linux-arm-kernel,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
On Wed, 06 Oct 2021 15:23:08 +0200, Alexander Stein wrote:
> TQMa8Mx is a SOM family using NXP i.MX8M[Q,QL, D] CPU
> MBa8Mx is a evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mq-<SOM>" for the module and
> "tq,imx8mq-<SOM>-<SBC>" for the module on that mainboard
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 6/7] dt-bindings: arm: fsl: add TQMa8Mx boards
@ 2021-10-14 19:56 ` Rob Herring
0 siblings, 0 replies; 26+ messages in thread
From: Rob Herring @ 2021-10-14 19:56 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Shawn Guo, linux-kernel, devicetree,
Catalin Marinas, Will Deacon, NXP Linux Team, linux-arm-kernel,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam
On Wed, 06 Oct 2021 15:23:08 +0200, Alexander Stein wrote:
> TQMa8Mx is a SOM family using NXP i.MX8M[Q,QL, D] CPU
> MBa8Mx is a evaluation mainbord for this SOM
>
> The SOM needs a mainboard, therefore we provide two compatibles here:
>
> "tq,imx8mq-<SOM>" for the module and
> "tq,imx8mq-<SOM>-<SBC>" for the module on that mainboard
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Documentation/devicetree/bindings/arm/fsl.yaml | 9 +++++++++
> 1 file changed, 9 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-15 2:34 ` Shawn Guo
-1 siblings, 0 replies; 26+ messages in thread
From: Shawn Guo @ 2021-10-15 2:34 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Sascha Hauer, Catalin Marinas, Will Deacon,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel
On Wed, Oct 06, 2021 at 03:23:04PM +0200, Alexander Stein wrote:
> This adds support for TQMa8MQML module on MBa8Mx board.
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++++
> .../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 ++++++++++++++++++
> arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++++
> 4 files changed, 895 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..032588e83f12 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
Keep the list sort alphabetically.
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> new file mode 100644
> index 000000000000..a0e22bef188e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> @@ -0,0 +1,259 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm-tqma8mqml.dtsi"
> +#include "mba8mx.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
> + compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> + aliases {
> + eeprom0 = &eeprom3;
> + mmc0 = &usdhc3;
> + mmc1 = &usdhc2;
> + mmc2 = &usdhc1;
> + rtc0 = &pcf85063;
> + rtc1 = &snvs_rtc;
> + };
> +
> + reg_usdhc2_vmmc: regulator-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + };
> +};
> +
> +&codec {
> + clock-names = "mclk";
> + clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
> +};
> +
> +&i2c1 {
> + expander2: gpio@27 {
> + compatible = "nxp,pca9555";
> + reg = <0x27>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_expander>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&sai3 {
> + assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
> + clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
> + <&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
> + <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
> + <&clk IMX8MM_AUDIO_PLL2_OUT>;
> +};
> +
> +&uart1 {
> + assigned-clocks = <&clk IMX8MM_CLK_UART1>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&uart2 {
> + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&iomuxc {
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006
> + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006
> + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006
> + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006
> + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006
> + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006
> + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006
> + >;
> + };
> +
> + pinctrl_expander: expandergrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
> + >;
> + };
> +
> + pinctrl_gpiobutton: gpiobuttongrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
> + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
> + MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
> + >;
> + };
> +
> + pinctrl_gpioled: gpioledgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
> + MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004
> + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004
> + MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004
> + MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
> + >;
> + };
> +
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
> + >;
> + };
> +
> + pinctrl_sai3: sai3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
> + MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
> + MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
> + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
> + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
> + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
> + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
> + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
> + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
> + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
Does it pass the 'grp$' pattern check in fsl,imx8mn-pinctrl.yaml?
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> new file mode 100644
> index 000000000000..5d947ca7b1bc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> @@ -0,0 +1,350 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
> + compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> + chosen {
> + };
Is it useful?
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* our minimum RAM config will be 1024 MiB */
> + reg = <0x00000000 0x40000000 0 0x40000000>;
> + };
> +
> + /* e-MMC IO, needed for HS modes */
> + reg_vcc1v8: regulator-vcc1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXML_VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + /* identical to buck4_reg, but should never change */
> + reg_vcc3v3: regulator-vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXML_VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* global autoconfigured region for contiguous allocations */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + /* 640 MiB */
> + size = <0 0x28000000>;
> + /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
> + alloc-ranges = <0 0x40000000 0 0x78000000>;
> + linux,cma-default;
> + };
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi>;
> + status = "okay";
> +
> + flash0: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <84000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + sensor0: temperature-sensor-eeprom@1b {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1b>;
> + };
> +
> + pca9450: pmic@25 {
> + compatible = "nxp,pca9450a";
> + reg = <0x25>;
> +
> + /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
> + pinctrl-0 = <&pinctrl_pmic>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio1>;
> + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + /* V_0V85_SOC: 0.85 */
> + buck1_reg: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VDD_ARM */
> + buck2_reg: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* V_0V85_GPU / DRAM / VPU */
> + buck3_reg: BUCK3 {
> + regulator-name = "BUCK3";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VCC3V3 -> VMMC, ... must not be changed */
> + buck4_reg: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
> + buck5_reg: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V1 -> RAM, ... must not be changed */
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_SNVS */
> + ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V8_SNVS */
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_ANA */
> + ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V9_MIPI */
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* VCC SD IO - switched using SD2 VSELECT */
> + ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
> +
> +
> + pcf85063: rtc@51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + quartz-load-femtofarads = <7000>;
> + };
> +
> + eeprom1: eeprom@53 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + read-only;
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +
> + eeprom0: eeprom@57 {
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + pagesize = <32>;
> + };
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + vmmc-supply = <®_vcc3v3>;
> + vqmmc-supply = <®_vcc1v8>;
> + status = "okay";
> +};
> +
> +/*
> + * Attention:
> + * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
> + * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
> + */
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_flexspi: flexspigrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
> + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
> + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
> + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
> + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
> + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004
> + MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> new file mode 100644
> index 000000000000..5b46ab79f05d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> @@ -0,0 +1,285 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/* TQ-Systems GmbH MBa8Mx baseboard */
> +
> +/ {
> + beeper {
> + compatible = "pwm-beeper";
> + pwms = <&pwm4 0 250000 0>;
> + beeper-hz = <4000>;
> + amp-supply = <®_vcc_3v3>;
> + };
> +
> + chosen {
> + bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
> + stdout-path = &uart3;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpiobutton>;
> + autorepeat;
> +
> + switch1 {
> + label = "switch1";
> + linux,code = <BTN_0>;
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> +
> + btn2: switch2 {
> + label = "switch2";
> + linux,code = <BTN_1>;
> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> +
> + switch3 {
> + label = "switch3";
> + linux,code = <BTN_2>;
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> + };
> +
> + gpio_leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpioled>;
> +
> + led1 {
> + label = "led1";
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + led2: led2 {
> + label = "led2";
> + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + reg_hub_vbus: regulator-hub-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "MBA8MX_HUB_VBUS";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "SN65DSI83_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_vcc_3v3: regulator-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MBA8MX_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + sound {
> + compatible = "fsl,imx-audio-tlv320aic32x4";
> + model = "tqm-tlv320aic32";
> + ssi-controller = <&sai3>;
> + audio-codec = <&codec>;
> + };
> +};
> +
> +&ecspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + phy-supply = <®_vcc_3v3>;
> + fsl,magic-packet;
> + mac-address = [ 00 00 00 00 00 00 ];
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@e {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0xe>;
> + interrupt-parent = <&expander2>;
> + interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,dp83867-rxctrl-strap-quirk;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + enet-phy-lane-no-swap;
> + reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <500000>;
> + reset-deassert-us = <500>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + expander0: gpio@23 {
> + compatible = "nxp,pca9555";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + sd-mux-oe-hog {
> + gpio-hog;
> + gpios = <8 0>;
> + output-low;
> + line-name = "SD_MUX_EN#";
> + };
> +
> + boot-cfg-oe-hog {
> + gpio-hog;
> + gpios = <12 0>;
> + output-high;
> + line-name = "BOOT_CFG_OE#";
> + };
> +
> + rst-usb-hub-hog {
> + gpio-hog;
> + gpios = <13 0>;
> + output-high;
> + line-name = "RST_USB_HUB#";
> + };
> + };
> +
> + expander1: gpio@24 {
> + compatible = "nxp,pca9555";
> + reg = <0x24>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-1 = <&pinctrl_i2c2_gpio>;
> + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + codec: tlv320aic3x04@18 {
Node name should be generic, i.e. 'audio-codec'.
Shawn
> + compatible = "ti,tlv320aic32x4";
> + reg = <0x18>;
> + reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
> + iov-supply = <®_vcc_3v3>;
> + ldoin-supply = <®_vcc_3v3>;
> + };
> +
> + sensor1: sensor@1f {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1f>;
> + };
> +
> + eeprom3: eeprom@57 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> + scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm3>;
> + status = "okay";
> +};
> +
> +&pwm4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm4>;
> + status = "okay";
> +};
> +
> +&sai3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai3>;
> + #sound-dai-cells = <0>;
> + assigned-clock-rates = <49152000>;
> + status = "okay";
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +/* console */
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +/* UART4 is assigned to Cortex-M4 */
> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + no-mmc;
> + no-sdio;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM
@ 2021-10-15 2:34 ` Shawn Guo
0 siblings, 0 replies; 26+ messages in thread
From: Shawn Guo @ 2021-10-15 2:34 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Sascha Hauer, Catalin Marinas, Will Deacon,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel
On Wed, Oct 06, 2021 at 03:23:04PM +0200, Alexander Stein wrote:
> This adds support for TQMa8MQML module on MBa8Mx board.
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-tqma8mqml-mba8mx.dts | 259 +++++++++++++
> .../boot/dts/freescale/imx8mm-tqma8mqml.dtsi | 350 ++++++++++++++++++
> arch/arm64/boot/dts/freescale/mba8mx.dtsi | 285 ++++++++++++++
> 4 files changed, 895 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> create mode 100644 arch/arm64/boot/dts/freescale/mba8mx.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index db9e36ebe932..032588e83f12 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
Keep the list sort alphabetically.
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> new file mode 100644
> index 000000000000..a0e22bef188e
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
> @@ -0,0 +1,259 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mm-tqma8mqml.dtsi"
> +#include "mba8mx.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
> + compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> + aliases {
> + eeprom0 = &eeprom3;
> + mmc0 = &usdhc3;
> + mmc1 = &usdhc2;
> + mmc2 = &usdhc1;
> + rtc0 = &pcf85063;
> + rtc1 = &snvs_rtc;
> + };
> +
> + reg_usdhc2_vmmc: regulator-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + };
> +};
> +
> +&codec {
> + clock-names = "mclk";
> + clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
> +};
> +
> +&i2c1 {
> + expander2: gpio@27 {
> + compatible = "nxp,pca9555";
> + reg = <0x27>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_expander>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&sai3 {
> + assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
> + clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
> + <&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
> + <&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
> + <&clk IMX8MM_AUDIO_PLL2_OUT>;
> +};
> +
> +&uart1 {
> + assigned-clocks = <&clk IMX8MM_CLK_UART1>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&uart2 {
> + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
> +};
> +
> +&iomuxc {
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000006
> + MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000006
> + MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000006
> + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000006
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000006
> + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000006
> + MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000006
> + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000006
> + >;
> + };
> +
> + pinctrl_expander: expandergrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
> + >;
> + };
> +
> + pinctrl_gpiobutton: gpiobuttongrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
> + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
> + MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
> + >;
> + };
> +
> + pinctrl_gpioled: gpioledgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
> + MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000004
> + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16 0x40000004
> + MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000004
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x40000004
> + MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x40000004
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
> + >;
> + };
> +
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
> + >;
> + };
> +
> + pinctrl_sai3: sai3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
> + MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
> + MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
> + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
> + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
> + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
> + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
> + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
> + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
> + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
Does it pass the 'grp$' pattern check in fsl,imx8mn-pinctrl.yaml?
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> new file mode 100644
> index 000000000000..5d947ca7b1bc
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
> @@ -0,0 +1,350 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
> + compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
> +
> + chosen {
> + };
Is it useful?
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* our minimum RAM config will be 1024 MiB */
> + reg = <0x00000000 0x40000000 0 0x40000000>;
> + };
> +
> + /* e-MMC IO, needed for HS modes */
> + reg_vcc1v8: regulator-vcc1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXML_VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + /* identical to buck4_reg, but should never change */
> + reg_vcc3v3: regulator-vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXML_VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* global autoconfigured region for contiguous allocations */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + /* 640 MiB */
> + size = <0 0x28000000>;
> + /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
> + alloc-ranges = <0 0x40000000 0 0x78000000>;
> + linux,cma-default;
> + };
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi>;
> + status = "okay";
> +
> + flash0: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <84000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + sensor0: temperature-sensor-eeprom@1b {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1b>;
> + };
> +
> + pca9450: pmic@25 {
> + compatible = "nxp,pca9450a";
> + reg = <0x25>;
> +
> + /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
> + pinctrl-0 = <&pinctrl_pmic>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio1>;
> + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + /* V_0V85_SOC: 0.85 */
> + buck1_reg: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VDD_ARM */
> + buck2_reg: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* V_0V85_GPU / DRAM / VPU */
> + buck3_reg: BUCK3 {
> + regulator-name = "BUCK3";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VCC3V3 -> VMMC, ... must not be changed */
> + buck4_reg: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
> + buck5_reg: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V1 -> RAM, ... must not be changed */
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_SNVS */
> + ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V8_SNVS */
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_ANA */
> + ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V9_MIPI */
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* VCC SD IO - switched using SD2 VSELECT */
> + ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
> +
> +
> + pcf85063: rtc@51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + quartz-load-femtofarads = <7000>;
> + };
> +
> + eeprom1: eeprom@53 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + read-only;
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +
> + eeprom0: eeprom@57 {
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + pagesize = <32>;
> + };
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + vmmc-supply = <®_vcc3v3>;
> + vqmmc-supply = <®_vcc1v8>;
> + status = "okay";
> +};
> +
> +/*
> + * Attention:
> + * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
> + * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
> + */
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_flexspi: flexspigrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82
> + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82
> + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82
> + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82
> + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82
> + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000004
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x40000004
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x40000004
> + MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x40000004
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x94
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + /* option USDHC3_RESET_B not defined, only in RM */
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x84
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> new file mode 100644
> index 000000000000..5b46ab79f05d
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
> @@ -0,0 +1,285 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include <dt-bindings/net/ti-dp83867.h>
> +
> +/* TQ-Systems GmbH MBa8Mx baseboard */
> +
> +/ {
> + beeper {
> + compatible = "pwm-beeper";
> + pwms = <&pwm4 0 250000 0>;
> + beeper-hz = <4000>;
> + amp-supply = <®_vcc_3v3>;
> + };
> +
> + chosen {
> + bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
> + stdout-path = &uart3;
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpiobutton>;
> + autorepeat;
> +
> + switch1 {
> + label = "switch1";
> + linux,code = <BTN_0>;
> + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> +
> + btn2: switch2 {
> + label = "switch2";
> + linux,code = <BTN_1>;
> + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> +
> + switch3 {
> + label = "switch3";
> + linux,code = <BTN_2>;
> + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
> + wakeup-source;
> + };
> + };
> +
> + gpio_leds: gpio-leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpioled>;
> +
> + led1 {
> + label = "led1";
> + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "default-on";
> + };
> +
> + led2: led2 {
> + label = "led2";
> + gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + reg_hub_vbus: regulator-hub-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "MBA8MX_HUB_VBUS";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + };
> +
> + reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "SN65DSI83_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> + reg_vcc_3v3: regulator-3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "MBA8MX_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + sound {
> + compatible = "fsl,imx-audio-tlv320aic32x4";
> + model = "tqm-tlv320aic32";
> + ssi-controller = <&sai3>;
> + audio-codec = <&codec>;
> + };
> +};
> +
> +&ecspi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1>;
> + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&ecspi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2>;
> + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> + phy-mode = "rgmii-id";
> + phy-handle = <ðphy0>;
> + phy-supply = <®_vcc_3v3>;
> + fsl,magic-packet;
> + mac-address = [ 00 00 00 00 00 00 ];
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy0: ethernet-phy@e {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <0xe>;
> + interrupt-parent = <&expander2>;
> + interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
> + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
> + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
> + ti,dp83867-rxctrl-strap-quirk;
> + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
> + enet-phy-lane-no-swap;
> + reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
> + reset-assert-us = <500000>;
> + reset-deassert-us = <500>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + expander0: gpio@23 {
> + compatible = "nxp,pca9555";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + sd-mux-oe-hog {
> + gpio-hog;
> + gpios = <8 0>;
> + output-low;
> + line-name = "SD_MUX_EN#";
> + };
> +
> + boot-cfg-oe-hog {
> + gpio-hog;
> + gpios = <12 0>;
> + output-high;
> + line-name = "BOOT_CFG_OE#";
> + };
> +
> + rst-usb-hub-hog {
> + gpio-hog;
> + gpios = <13 0>;
> + output-high;
> + line-name = "RST_USB_HUB#";
> + };
> + };
> +
> + expander1: gpio@24 {
> + compatible = "nxp,pca9555";
> + reg = <0x24>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + pinctrl-1 = <&pinctrl_i2c2_gpio>;
> + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + codec: tlv320aic3x04@18 {
Node name should be generic, i.e. 'audio-codec'.
Shawn
> + compatible = "ti,tlv320aic32x4";
> + reg = <0x18>;
> + reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
> + iov-supply = <®_vcc_3v3>;
> + ldoin-supply = <®_vcc_3v3>;
> + };
> +
> + sensor1: sensor@1f {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1f>;
> + };
> +
> + eeprom3: eeprom@57 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + reg = <0x57>;
> + pagesize = <16>;
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_gpio>;
> + scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm3>;
> + status = "okay";
> +};
> +
> +&pwm4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm4>;
> + status = "okay";
> +};
> +
> +&sai3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_sai3>;
> + #sound-dai-cells = <0>;
> + assigned-clock-rates = <49152000>;
> + status = "okay";
> +};
> +
> +&snvs_pwrkey {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + status = "okay";
> +};
> +
> +/* console */
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart3>;
> + status = "okay";
> +};
> +
> +/* UART4 is assigned to Cortex-M4 */
> +
> +&usdhc2 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + disable-wp;
> + no-mmc;
> + no-sdio;
> + vmmc-supply = <®_usdhc2_vmmc>;
> + status = "okay";
> +};
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 5/7] arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
2021-10-06 13:23 ` Alexander Stein
@ 2021-10-15 2:41 ` Shawn Guo
-1 siblings, 0 replies; 26+ messages in thread
From: Shawn Guo @ 2021-10-15 2:41 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Sascha Hauer, Catalin Marinas, Will Deacon,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel
On Wed, Oct 06, 2021 at 03:23:07PM +0200, Alexander Stein wrote:
> This adds support for TQMa8MQNL module on MBa8Mx board.
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++++
> .../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 ++++++++++++++++++
> 3 files changed, 629 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 032588e83f12..ed166e6d20f6 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> new file mode 100644
> index 000000000000..3733f79b29cf
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> @@ -0,0 +1,283 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mn-tqma8mqnl.dtsi"
> +#include "mba8mx.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
> + compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
> +
> + aliases {
> + eeprom0 = &eeprom3;
> + mmc0 = &usdhc3;
> + mmc1 = &usdhc2;
> + mmc2 = &usdhc1;
> + rtc0 = &pcf85063;
> + rtc1 = &snvs_rtc;
> + };
> +
> + reg_usdhc2_vmmc: regulator-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + };
> +};
> +
> +&codec {
> + clock-names = "mclk";
> + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
One level indent is enough.
> +};
> +
> +/* Located on TQMa8MxML-ADAP */
> +&gpio2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb0hub_sel>;
> +
> + sel-usb-hub-hog {
> + gpio-hog;
> + gpios = <1 GPIO_ACTIVE_HIGH>;
> + output-high;
> + };
> +};
> +
> +&i2c1 {
> + expander2: gpio@27 {
> + compatible = "nxp,pca9555";
> + reg = <0x27>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_expander2>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&sai3 {
> + assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
> + clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
> + <&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
> + <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
> + <&clk IMX8MN_AUDIO_PLL2_OUT>;
> +};
> +
> +&usbotg1 {
> + dr_mode = "host";
> + disable-over-current;
> + power-active-high;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000146
> + MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000146
> + MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000146
> + MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000146
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000146
> + MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000146
> + MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000146
> + MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000146
> + >;
> + };
> +
> + pinctrl_expander2: expander2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
> + MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
> + MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
> + MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
> + MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
> + MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
> + MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
> + MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
> + MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
> + MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
> + MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
> + MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
> + MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
> + MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
> + >;
> + };
> +
> + pinctrl_gpiobutton: gpiobuttongrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
> + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
> + MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
> + >;
> + };
> +
> + pinctrl_gpioled: gpioledgrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
> + MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001C4
> + MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001C4
> + MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001C4
> + MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001C4
> + MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001C4
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
> + >;
> + };
> +
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
> + >;
> + };
> +
> + pinctrl_sai3: sai3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
> + MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
> + MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
> + MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
> + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
> + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
> + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
> + MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
> + MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
> + MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
> + MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_usb0hub_sel: usb0hub_sel {
Doesn't match 'grp$' pattern.
> + fsl,pins = <
> + /* SEL_USB_HUB_B */
> + MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x84
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84
> + MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84
> + MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x1C4
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
> new file mode 100644
> index 000000000000..ab474529d66f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
> @@ -0,0 +1,345 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include "imx8mn.dtsi"
> +
> +/ {
> + model = "TQ-Systems i.MX8MN TQMa8MxNL";
> + compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
> +
> + chosen {
> + };
Really needed?
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* our minimum RAM config will be 1024 MiB */
> + reg = <0x00000000 0x40000000 0 0x40000000>;
> + };
> +
> + /* e-MMC IO, needed for HS modes */
> + reg_vcc1v8: regulator-vcc1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXNL_VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
always-on is meaningless for a fixed regulator that doesn't have any
on/off control.
Shawn
> + };
> +
> + reg_vcc3v3: regulator-vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXNL_VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* global autoconfigured region for contiguous allocations */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + /* 640 MiB */
> + size = <0 0x28000000>;
> + /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
> + alloc-ranges = <0 0x40000000 0 0x78000000>;
> + linux,cma-default;
> + };
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi>;
> + status = "okay";
> +
> + flash0: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <84000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + sensor0: temperature-sensor-eeprom@1b {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1b>;
> + };
> +
> + pca9450: pmic@25 {
> + compatible = "nxp,pca9450a";
> + reg = <0x25>;
> +
> + /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
> + pinctrl-0 = <&pinctrl_pmic>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio1>;
> + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + /* V_0V85_SOC: 0.85 .. 0.95 */
> + buck1_reg: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VDD_ARM */
> + buck2_reg: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
> + buck3_reg: BUCK3 {
> + regulator-name = "BUCK3";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VCC3V3 -> VMMC, ... must not be changed */
> + buck4_reg: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
> + buck5_reg: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V1 -> RAM, ... must not be changed */
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_SNVS */
> + ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V8_SNVS */
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_ANA */
> + ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V9_MIPI */
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* VCC SD IO - switched using SD2 VSELECT */
> + ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
> +
> + pcf85063: rtc@51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + quartz-load-femtofarads = <7000>;
> + };
> +
> + eeprom1: eeprom@53 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + read-only;
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +
> + eeprom0: eeprom@57 {
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + pagesize = <32>;
> + };
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + vmmc-supply = <®_vcc3v3>;
> + vqmmc-supply = <®_vcc1v8>;
> + status = "okay";
> +};
> +
> +/*
> + * Attention:
> + * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
> + * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
> + */
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_flexspi: flexspigrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84
> + MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84
> + MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84
> + MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84
> + MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84
> + MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4
> + MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4
> + MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
> + >;
> + };
> +};
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 26+ messages in thread
* Re: [PATCH 5/7] arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN
@ 2021-10-15 2:41 ` Shawn Guo
0 siblings, 0 replies; 26+ messages in thread
From: Shawn Guo @ 2021-10-15 2:41 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Sascha Hauer, Catalin Marinas, Will Deacon,
Pengutronix Kernel Team, Fabio Estevam, NXP Linux Team,
devicetree, linux-kernel, linux-arm-kernel
On Wed, Oct 06, 2021 at 03:23:07PM +0200, Alexander Stein wrote:
> This adds support for TQMa8MQNL module on MBa8Mx board.
>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts | 283 ++++++++++++++
> .../boot/dts/freescale/imx8mn-tqma8mqnl.dtsi | 345 ++++++++++++++++++
> 3 files changed, 629 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 032588e83f12..ed166e6d20f6 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -48,6 +48,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> new file mode 100644
> index 000000000000..3733f79b29cf
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
> @@ -0,0 +1,283 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +/dts-v1/;
> +
> +#include "imx8mn-tqma8mqnl.dtsi"
> +#include "mba8mx.dtsi"
> +
> +/ {
> + model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
> + compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
> +
> + aliases {
> + eeprom0 = &eeprom3;
> + mmc0 = &usdhc3;
> + mmc1 = &usdhc2;
> + mmc2 = &usdhc1;
> + rtc0 = &pcf85063;
> + rtc1 = &snvs_rtc;
> + };
> +
> + reg_usdhc2_vmmc: regulator-vmmc {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
> + regulator-name = "VSD_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + startup-delay-us = <100>;
> + off-on-delay-us = <12000>;
> + };
> +};
> +
> +&codec {
> + clock-names = "mclk";
> + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
One level indent is enough.
> +};
> +
> +/* Located on TQMa8MxML-ADAP */
> +&gpio2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb0hub_sel>;
> +
> + sel-usb-hub-hog {
> + gpio-hog;
> + gpios = <1 GPIO_ACTIVE_HIGH>;
> + output-high;
> + };
> +};
> +
> +&i2c1 {
> + expander2: gpio@27 {
> + compatible = "nxp,pca9555";
> + reg = <0x27>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + vcc-supply = <®_vcc_3v3>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_expander2>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&sai3 {
> + assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
> + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
> + clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
> + clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
> + <&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
> + <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
> + <&clk IMX8MN_AUDIO_PLL2_OUT>;
> +};
> +
> +&usbotg1 {
> + dr_mode = "host";
> + disable-over-current;
> + power-active-high;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK 0x00000146
> + MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x00000146
> + MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO 0x00000146
> + MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x00000146
> + >;
> + };
> +
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x00000146
> + MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x00000146
> + MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x00000146
> + MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x00000146
> + >;
> + };
> +
> + pinctrl_expander2: expander2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x94
> + >;
> + };
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x40000002
> + MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x40000002
> + MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x14
> + MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x14
> + MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x14
> + MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x14
> + MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x90
> + MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x90
> + MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x90
> + MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x90
> + MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x14
> + MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x90
> + MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x90
> + MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x14
> + >;
> + };
> +
> + pinctrl_gpiobutton: gpiobuttongrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x84
> + MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x84
> + MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0 0x84
> + >;
> + };
> +
> + pinctrl_gpioled: gpioledgrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x84
> + MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14 0x84
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001C4
> + MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c2_gpio: i2c2gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16 0x400001C4
> + MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001C4
> + MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001C4
> + >;
> + };
> +
> + pinctrl_i2c3_gpio: i2c3gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001C4
> + MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001C4
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT 0x14
> + >;
> + };
> +
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT 0x14
> + >;
> + };
> +
> + pinctrl_sai3: sai3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0x94
> + MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK 0x94
> + MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC 0x94
> + MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0x94
> + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0x94
> + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0x94
> + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0x94
> + >;
> + };
> +
> + pinctrl_uart1: uart1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x16
> + MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x16
> + MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX 0x16
> + MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX 0x16
> + MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX 0x16
> + >;
> + };
> +
> + pinctrl_usb0hub_sel: usb0hub_sel {
Doesn't match 'grp$' pattern.
> + fsl,pins = <
> + /* SEL_USB_HUB_B */
> + MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1 0x84
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x84
> + MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x84
> + MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID 0x1C4
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x1d4
> + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x84
> + >;
> + };
> +
> + pinctrl_usdhc2_gpio: usdhc2grpgpio {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12 0x84
> + >;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
> new file mode 100644
> index 000000000000..ab474529d66f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
> @@ -0,0 +1,345 @@
> +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
> +/*
> + * Copyright 2020-2021 TQ-Systems GmbH
> + */
> +
> +#include "imx8mn.dtsi"
> +
> +/ {
> + model = "TQ-Systems i.MX8MN TQMa8MxNL";
> + compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
> +
> + chosen {
> + };
Really needed?
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* our minimum RAM config will be 1024 MiB */
> + reg = <0x00000000 0x40000000 0 0x40000000>;
> + };
> +
> + /* e-MMC IO, needed for HS modes */
> + reg_vcc1v8: regulator-vcc1v8 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXNL_VCC1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
always-on is meaningless for a fixed regulator that doesn't have any
on/off control.
Shawn
> + };
> +
> + reg_vcc3v3: regulator-vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "TQMA8MXNL_VCC3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* global autoconfigured region for contiguous allocations */
> + linux,cma {
> + compatible = "shared-dma-pool";
> + reusable;
> + /* 640 MiB */
> + size = <0 0x28000000>;
> + /* 1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
> + alloc-ranges = <0 0x40000000 0 0x78000000>;
> + linux,cma-default;
> + };
> + };
> +};
> +
> +&A53_0 {
> + cpu-supply = <&buck2_reg>;
> +};
> +
> +&flexspi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexspi>;
> + status = "okay";
> +
> + flash0: flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <84000000>;
> + spi-tx-bus-width = <4>;
> + spi-rx-bus-width = <4>;
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> + status = "okay";
> +
> + sensor0: temperature-sensor-eeprom@1b {
> + compatible = "nxp,se97", "jedec,jc-42.4-temp";
> + reg = <0x1b>;
> + };
> +
> + pca9450: pmic@25 {
> + compatible = "nxp,pca9450a";
> + reg = <0x25>;
> +
> + /* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
> + pinctrl-0 = <&pinctrl_pmic>;
> + pinctrl-names = "default";
> + interrupt-parent = <&gpio1>;
> + interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
> +
> + regulators {
> + /* V_0V85_SOC: 0.85 .. 0.95 */
> + buck1_reg: BUCK1 {
> + regulator-name = "BUCK1";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VDD_ARM */
> + buck2_reg: BUCK2 {
> + regulator-name = "BUCK2";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + nxp,dvs-run-voltage = <950000>;
> + nxp,dvs-standby-voltage = <850000>;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
> + buck3_reg: BUCK3 {
> + regulator-name = "BUCK3";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <950000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <3125>;
> + };
> +
> + /* VCC3V3 -> VMMC, ... must not be changed */
> + buck4_reg: BUCK4 {
> + regulator-name = "BUCK4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
> + buck5_reg: BUCK5 {
> + regulator-name = "BUCK5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V1 -> RAM, ... must not be changed */
> + buck6_reg: BUCK6 {
> + regulator-name = "BUCK6";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_SNVS */
> + ldo1_reg: LDO1 {
> + regulator-name = "LDO1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V8_SNVS */
> + ldo2_reg: LDO2 {
> + regulator-name = "LDO2";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <850000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_1V8_ANA */
> + ldo3_reg: LDO3 {
> + regulator-name = "LDO3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* V_0V9_MIPI */
> + ldo4_reg: LDO4 {
> + regulator-name = "LDO4";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + /* VCC SD IO - switched using SD2 VSELECT */
> + ldo5_reg: LDO5 {
> + regulator-name = "LDO5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + };
> + };
> + };
> +
> + pcf85063: rtc@51 {
> + compatible = "nxp,pcf85063a";
> + reg = <0x51>;
> + quartz-load-femtofarads = <7000>;
> + };
> +
> + eeprom1: eeprom@53 {
> + compatible = "nxp,se97b", "atmel,24c02";
> + read-only;
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +
> + eeprom0: eeprom@57 {
> + compatible = "atmel,24c64";
> + reg = <0x57>;
> + pagesize = <32>;
> + };
> +};
> +
> +&usdhc3 {
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
> + bus-width = <8>;
> + non-removable;
> + no-sd;
> + no-sdio;
> + vmmc-supply = <®_vcc3v3>;
> + vqmmc-supply = <®_vcc1v8>;
> + status = "okay";
> +};
> +
> +/*
> + * Attention:
> + * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
> + * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
> + */
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl_flexspi: flexspigrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x84
> + MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84
> + MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84
> + MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84
> + MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84
> + MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c4
> + MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c4
> + >;
> + };
> +
> + pinctrl_i2c1_gpio: i2c1gpiogrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c4
> + MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c4
> + >;
> + };
> +
> + pinctrl_pmic: pmicgrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x84
> + >;
> + };
> +
> + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
> + fsl,pins = <
> + MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d4
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d2
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x1d6
> + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d2
> + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4
> + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4
> + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4
> + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4
> + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x84
> + MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B 0x84
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x84
> + >;
> + };
> +};
> --
> 2.25.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 26+ messages in thread
end of thread, other threads:[~2021-10-15 2:43 UTC | newest]
Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-10-06 13:23 [PATCH 0/7] Support for some TQMa8M* boards Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-06 13:23 ` [PATCH 1/7] dt-bindings: arm: fsl: add TQMa8MxML boards Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-14 19:55 ` Rob Herring
2021-10-14 19:55 ` Rob Herring
2021-10-06 13:23 ` [PATCH 2/7] arm64: dts: freescale: add initial tree for TQMa8MQML with i.MX8MM Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-15 2:34 ` Shawn Guo
2021-10-15 2:34 ` Shawn Guo
2021-10-06 13:23 ` [PATCH 3/7] arm64: defconfig: enable drivers for TQ TQMa8MxML-MBa8Mx Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-06 13:23 ` [PATCH 4/7] dt-bindings: arm: fsl: add TQMa8MxNL boards Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-14 19:55 ` Rob Herring
2021-10-14 19:55 ` Rob Herring
2021-10-06 13:23 ` [PATCH 5/7] arm64: dts: freescale: add initial tree for TQMa8MQNL with i.MX8MN Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-15 2:41 ` Shawn Guo
2021-10-15 2:41 ` Shawn Guo
2021-10-06 13:23 ` [PATCH 6/7] dt-bindings: arm: fsl: add TQMa8Mx boards Alexander Stein
2021-10-06 13:23 ` Alexander Stein
2021-10-14 19:56 ` Rob Herring
2021-10-14 19:56 ` Rob Herring
2021-10-06 13:23 ` [PATCH 7/7] arm64: dts: freescale: add initial tree for TQMa8Mx with i.MX8M Alexander Stein
2021-10-06 13:23 ` Alexander Stein
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.