[PATCH v3 0/4] ti-sn65dsi83 patches

[PATCH v3 0/4] ti-sn65dsi83 patches

[Alexander Stein]

Changes in V3 of this set:
* Do not require vcc-supply in bindings, making it purely optional
* Move regulator enable/disable to sn65dsi83_atomic_pre_enable and
  sn65dsi83_atomic_disable

Changes in V2 of this set:
* Add patch from Laurent for fixing the binding regarding optional GPIO
* Reorder patches so bindings are changed beforehand
* Add small fixes from Sam's review

Alexander Stein (3):
  drm/bridge: ti-sn65dsi83: Make enable GPIO optional
  dt-bindings: drm/bridge: ti-sn65dsi83: Add vcc supply bindings
  drm/bridge: ti-sn65dsi83: Add vcc supply regulator support

Laurent Pinchart (1):
  dt-bindings: display: bridge: sn65dsi83: Make enable GPIO optional

 .../bindings/display/bridge/ti,sn65dsi83.yaml |  5 ++++-
 drivers/gpu/drm/bridge/ti-sn65dsi83.c         | 21 ++++++++++++++++++-
 2 files changed, 24 insertions(+), 2 deletions(-)

-- 
2.25.1

[PATCH v3 1/4] dt-bindings: display: bridge: sn65dsi83: Make enable GPIO optional

[Alexander Stein]

From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

The SN65DSI8x EN signal may be tied to VCC, or otherwise controlled by
means not available to the kernel. Make the GPIO optional.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml         | 1 -
 1 file changed, 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
index 07b20383cbca..a5779bf17849 100644
--- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
@@ -93,7 +93,6 @@ properties:
 required:
   - compatible
   - reg
-  - enable-gpios
   - ports
 
 allOf:
-- 
2.25.1

[PATCH v3 2/4] drm/bridge: ti-sn65dsi83: Make enable GPIO optional

[Alexander Stein]

The enable signal may not be controllable by the kernel. Make it
optional.
This is a similar to commit bbda1704fc15 ("drm/bridge: ti-sn65dsi86: Make
enable GPIO optional")

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 drivers/gpu/drm/bridge/ti-sn65dsi83.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
index a32f70bc68ea..9072342566f3 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
@@ -671,7 +671,8 @@ static int sn65dsi83_probe(struct i2c_client *client,
 		model = id->driver_data;
 	}
 
-	ctx->enable_gpio = devm_gpiod_get(ctx->dev, "enable", GPIOD_OUT_LOW);
+	ctx->enable_gpio = devm_gpiod_get_optional(ctx->dev, "enable",
+						   GPIOD_OUT_LOW);
 	if (IS_ERR(ctx->enable_gpio))
 		return PTR_ERR(ctx->enable_gpio);
 
-- 
2.25.1

[PATCH v3 3/4] dt-bindings: drm/bridge: ti-sn65dsi83: Add vcc supply bindings

[Alexander Stein]

Add a VCC regulator which needs to be enabled before the EN pin is
released.

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml      | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
index a5779bf17849..f1e4f149ccb4 100644
--- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
@@ -32,6 +32,9 @@ properties:
     maxItems: 1
     description: GPIO specifier for bridge_en pin (active high).
 
+  vcc-supply:
+    description: A 1.8V power supply (see regulator/regulator.yaml).
+
   ports:
     $ref: /schemas/graph.yaml#/properties/ports
 
@@ -134,6 +137,7 @@ examples:
             reg = <0x2d>;
 
             enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+            vcc-supply = <&reg_sn65dsi83_1v8>;
 
             ports {
                 #address-cells = <1>;
-- 
2.25.1

[PATCH v3 4/4] drm/bridge: ti-sn65dsi83: Add vcc supply regulator support

[Alexander Stein]

VCC needs to be enabled before releasing the enable GPIO.

Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
 drivers/gpu/drm/bridge/ti-sn65dsi83.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
index 9072342566f3..c55c45d5d29a 100644
--- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
+++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
@@ -33,6 +33,7 @@
 #include <linux/of_device.h>
 #include <linux/of_graph.h>
 #include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
 
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_bridge.h>
@@ -143,6 +144,7 @@ struct sn65dsi83 {
 	struct mipi_dsi_device		*dsi;
 	struct drm_bridge		*panel_bridge;
 	struct gpio_desc		*enable_gpio;
+	struct regulator		*vcc;
 	int				dsi_lanes;
 	bool				lvds_dual_link;
 	bool				lvds_dual_link_even_odd_swap;
@@ -292,6 +294,11 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
 					struct drm_bridge_state *old_bridge_state)
 {
 	struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
+	int ret;
+
+	ret = regulator_enable(ctx->vcc);
+	if (ret)
+		dev_err(ctx->dev, "Failed to enable vcc: %i\n", ret);
 
 	/*
 	 * Reset the chip, pull EN line low for t_reset=10ms,
@@ -536,9 +543,14 @@ static void sn65dsi83_atomic_post_disable(struct drm_bridge *bridge,
 					  struct drm_bridge_state *old_bridge_state)
 {
 	struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
+	int ret;
 
 	/* Put the chip in reset, pull EN line low. */
 	gpiod_set_value(ctx->enable_gpio, 0);
+
+	ret = regulator_disable(ctx->vcc);
+	if (ret)
+		dev_err(ctx->dev, "Failed to disable vcc: %i\n", ret);
 }
 
 static enum drm_mode_status
@@ -647,6 +659,12 @@ static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model)
 
 	ctx->panel_bridge = panel_bridge;
 
+	ctx->vcc = devm_regulator_get(dev, "vcc");
+	if (IS_ERR(ctx->vcc))
+		return dev_err_probe(dev, PTR_ERR(ctx->vcc),
+				     "Failed to get supply 'vcc': %pe\n",
+				     ctx->vcc);
+
 	return 0;
 }
 
-- 
2.25.1

Re: [PATCH v3 1/4] dt-bindings: display: bridge: sn65dsi83: Make enable GPIO optional

[Rob Herring]

On Tue, 19 Oct 2021 08:52:36 +0200, Alexander Stein wrote:
> From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> 
> The SN65DSI8x EN signal may be tied to VCC, or otherwise controlled by
> means not available to the kernel. Make the GPIO optional.
> 
> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
>  .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml         | 1 -
>  1 file changed, 1 deletion(-)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 3/4] dt-bindings: drm/bridge: ti-sn65dsi83: Add vcc supply bindings

[Rob Herring]

On Tue, 19 Oct 2021 08:52:38 +0200, Alexander Stein wrote:
> Add a VCC regulator which needs to be enabled before the EN pin is
> released.
> 
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
>  .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml      | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 3/4] dt-bindings: drm/bridge: ti-sn65dsi83: Add vcc supply bindings

[Laurent Pinchart]

Hi Alexander,

Thank you for the patch.

On Tue, Oct 19, 2021 at 08:52:38AM +0200, Alexander Stein wrote:
> Add a VCC regulator which needs to be enabled before the EN pin is
> released.
> 
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
>  .../devicetree/bindings/display/bridge/ti,sn65dsi83.yaml      | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
> index a5779bf17849..f1e4f149ccb4 100644
> --- a/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
> +++ b/Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml
> @@ -32,6 +32,9 @@ properties:
>      maxItems: 1
>      description: GPIO specifier for bridge_en pin (active high).
>  
> +  vcc-supply:
> +    description: A 1.8V power supply (see regulator/regulator.yaml).

I would have dropped the part between parentheses as it's kind of
implied, but I don't mind much.

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> +
>    ports:
>      $ref: /schemas/graph.yaml#/properties/ports
>  
> @@ -134,6 +137,7 @@ examples:
>              reg = <0x2d>;
>  
>              enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
> +            vcc-supply = <&reg_sn65dsi83_1v8>;
>  
>              ports {
>                  #address-cells = <1>;

-- 
Regards,

Laurent Pinchart

Re: [PATCH v3 4/4] drm/bridge: ti-sn65dsi83: Add vcc supply regulator support

[Laurent Pinchart]

Hi Alexander,

Thank you for the patch.

On Tue, Oct 19, 2021 at 08:52:39AM +0200, Alexander Stein wrote:
> VCC needs to be enabled before releasing the enable GPIO.
> 
> Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>

Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

> ---
>  drivers/gpu/drm/bridge/ti-sn65dsi83.c | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi83.c b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> index 9072342566f3..c55c45d5d29a 100644
> --- a/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> +++ b/drivers/gpu/drm/bridge/ti-sn65dsi83.c
> @@ -33,6 +33,7 @@
>  #include <linux/of_device.h>
>  #include <linux/of_graph.h>
>  #include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
>  
>  #include <drm/drm_atomic_helper.h>
>  #include <drm/drm_bridge.h>
> @@ -143,6 +144,7 @@ struct sn65dsi83 {
>  	struct mipi_dsi_device		*dsi;
>  	struct drm_bridge		*panel_bridge;
>  	struct gpio_desc		*enable_gpio;
> +	struct regulator		*vcc;
>  	int				dsi_lanes;
>  	bool				lvds_dual_link;
>  	bool				lvds_dual_link_even_odd_swap;
> @@ -292,6 +294,11 @@ static void sn65dsi83_atomic_pre_enable(struct drm_bridge *bridge,
>  					struct drm_bridge_state *old_bridge_state)
>  {
>  	struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
> +	int ret;
> +
> +	ret = regulator_enable(ctx->vcc);
> +	if (ret)
> +		dev_err(ctx->dev, "Failed to enable vcc: %i\n", ret);
>  
>  	/*
>  	 * Reset the chip, pull EN line low for t_reset=10ms,
> @@ -536,9 +543,14 @@ static void sn65dsi83_atomic_post_disable(struct drm_bridge *bridge,
>  					  struct drm_bridge_state *old_bridge_state)
>  {
>  	struct sn65dsi83 *ctx = bridge_to_sn65dsi83(bridge);
> +	int ret;
>  
>  	/* Put the chip in reset, pull EN line low. */
>  	gpiod_set_value(ctx->enable_gpio, 0);
> +
> +	ret = regulator_disable(ctx->vcc);
> +	if (ret)
> +		dev_err(ctx->dev, "Failed to disable vcc: %i\n", ret);
>  }
>  
>  static enum drm_mode_status
> @@ -647,6 +659,12 @@ static int sn65dsi83_parse_dt(struct sn65dsi83 *ctx, enum sn65dsi83_model model)
>  
>  	ctx->panel_bridge = panel_bridge;
>  
> +	ctx->vcc = devm_regulator_get(dev, "vcc");
> +	if (IS_ERR(ctx->vcc))
> +		return dev_err_probe(dev, PTR_ERR(ctx->vcc),
> +				     "Failed to get supply 'vcc': %pe\n",
> +				     ctx->vcc);
> +
>  	return 0;
>  }
>  

-- 
Regards,

Laurent Pinchart