* [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250
@ 2022-01-02 15:58 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-02 15:58 UTC (permalink / raw)
To: Krzysztof Kozlowski, Andi Shyti, Mark Brown, Rob Herring,
linux-spi, linux-samsung-soc, devicetree, linux-kernel,
linux-arm-kernel
"dmas" property should be rather an array of phandles, as dtschema
points.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
---
arch/arm/boot/dts/exynos5250.dtsi | 9 +++------
1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 139778928b93..102bb57bf704 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -496,8 +496,7 @@ spi_0: spi@12d20000 {
status = "disabled";
reg = <0x12d20000 0x100>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma0 5
- &pdma0 4>;
+ dmas = <&pdma0 5>, <&pdma0 4>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
@@ -512,8 +511,7 @@ spi_1: spi@12d30000 {
status = "disabled";
reg = <0x12d30000 0x100>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma1 5
- &pdma1 4>;
+ dmas = <&pdma1 5>, <&pdma1 4>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
@@ -528,8 +526,7 @@ spi_2: spi@12d40000 {
status = "disabled";
reg = <0x12d40000 0x100>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma0 7
- &pdma0 6>;
+ dmas = <&pdma0 7>, <&pdma0 6>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250
@ 2022-01-02 15:58 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-02 15:58 UTC (permalink / raw)
To: Krzysztof Kozlowski, Andi Shyti, Mark Brown, Rob Herring,
linux-spi, linux-samsung-soc, devicetree, linux-kernel,
linux-arm-kernel
"dmas" property should be rather an array of phandles, as dtschema
points.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
---
arch/arm/boot/dts/exynos5250.dtsi | 9 +++------
1 file changed, 3 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 139778928b93..102bb57bf704 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -496,8 +496,7 @@ spi_0: spi@12d20000 {
status = "disabled";
reg = <0x12d20000 0x100>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma0 5
- &pdma0 4>;
+ dmas = <&pdma0 5>, <&pdma0 4>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
@@ -512,8 +511,7 @@ spi_1: spi@12d30000 {
status = "disabled";
reg = <0x12d30000 0x100>;
interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma1 5
- &pdma1 4>;
+ dmas = <&pdma1 5>, <&pdma1 4>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
@@ -528,8 +526,7 @@ spi_2: spi@12d40000 {
status = "disabled";
reg = <0x12d40000 0x100>;
interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
- dmas = <&pdma0 7
- &pdma0 6>;
+ dmas = <&pdma0 7>, <&pdma0 6>;
dma-names = "tx", "rx";
#address-cells = <1>;
#size-cells = <0>;
--
2.32.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
2022-01-02 15:58 ` Krzysztof Kozlowski
@ 2022-01-02 15:58 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-02 15:58 UTC (permalink / raw)
To: Krzysztof Kozlowski, Andi Shyti, Mark Brown, Rob Herring,
linux-spi, linux-samsung-soc, devicetree, linux-kernel,
linux-arm-kernel
Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
controller bindings to DT schema format
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
---
.../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
.../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
MAINTAINERS | 2 +-
3 files changed, 221 insertions(+), 123 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
new file mode 100644
index 000000000000..195bfafe05fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
@@ -0,0 +1,220 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S3C/S5P/Exynos SoC SPI controller
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description:
+ All the SPI controller nodes should be represented in the aliases node using
+ the following format 'spi{n}' where n is a unique number for the alias.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - samsung,s3c2443-spi
+ - samsung,s3c6410-spi
+ - samsung,s5pv210-spi
+ - samsung,exynos5433-spi
+ - const: samsung,exynos7-spi
+ deprecated: true
+
+ clocks:
+ minItems: 2
+ maxItems: 3
+
+ clock-names:
+ minItems: 2
+ maxItems: 3
+
+ cs-gpios: true
+
+ dmas:
+ minItems: 2
+ maxItems: 2
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ interrupts:
+ maxItems: 1
+
+ no-cs-readback:
+ description:
+ The CS line is disconnected, therefore the device should not operate
+ based on CS signalling.
+ type: boolean
+
+ num-cs:
+ minimum: 1
+ maximum: 4
+ default: 1
+
+ samsung,spi-src-clk:
+ description:
+ If the spi controller includes a internal clock mux to select the clock
+ source for the spi bus clock, this property can be used to indicate the
+ clock to be used for driving the spi bus clock. If not specified, the
+ clock number 0 is used as default.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ "^.*@[0-9a-f]+$":
+ type: object
+
+ allOf:
+ - $ref: spi-peripheral-props.yaml
+
+ properties:
+ controller-data:
+ type: object
+ additionalProperties: false
+
+ properties:
+ samsung,spi-feedback-delay:
+ description: |
+ The sampling phase shift to be applied on the miso line (to account
+ for any lag in the miso line). Valid values:
+ - 0: No phase shift.
+ - 1: 90 degree phase shift sampling.
+ - 2: 180 degree phase shift sampling.
+ - 3: 270 degree phase shift sampling.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ required:
+ - samsung,spi-feedback-delay
+
+ required:
+ - controller-data
+
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - clocks
+ - clock-names
+ - dmas
+ - dma-names
+ - interrupts
+ - reg
+
+allOf:
+ - $ref: spi-controller.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos5433-spi
+ then:
+ properties:
+ clocks:
+ minItems: 3
+ maxItems: 3
+ clock-names:
+ items:
+ - const: spi
+ - enum:
+ - spi_busclk0
+ - spi_busclk1
+ - spi_busclk2
+ - spi_busclk3
+ - const: spi_ioclk
+ else:
+ properties:
+ clocks:
+ minItems: 2
+ maxItems: 2
+ clock-names:
+ items:
+ - const: spi
+ - enum:
+ - spi_busclk0
+ - spi_busclk1
+ - spi_busclk2
+ - spi_busclk3
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos5433.h>
+ #include <dt-bindings/clock/samsung,s2mps11.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi@14d30000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d30000 0x100>;
+ interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&pdma0 11>, <&pdma0 10>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
+ clock-names = "spi",
+ "spi_busclk0",
+ "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ num-cs = <1>;
+
+ cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ audio-codec@0 {
+ compatible = "wlf,wm5110";
+ reg = <0x0>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpa0>;
+ interrupts = <4 IRQ_TYPE_NONE>;
+ clocks = <&pmu_system_controller 0>,
+ <&s2mps13_osc S2MPS11_CLK_BT>;
+ clock-names = "mclk1", "mclk2";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ wlf,micd-detect-debounce = <300>;
+ wlf,micd-bias-start-time = <0x1>;
+ wlf,micd-rate = <0x7>;
+ wlf,micd-dbtime = <0x2>;
+ wlf,micd-force-micbias;
+ wlf,micd-configs = <0x0 1 0>;
+ wlf,hpdet-channel = <1>;
+ wlf,gpsw = <0x1>;
+ wlf,inmode = <2 0 2 0>;
+
+ wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
+ wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
+
+ /* core supplies */
+ AVDD-supply = <&ldo18_reg>;
+ DBVDD1-supply = <&ldo18_reg>;
+ CPVDD-supply = <&ldo18_reg>;
+ DBVDD2-supply = <&ldo18_reg>;
+ DBVDD3-supply = <&ldo18_reg>;
+ SPKVDDL-supply = <&ldo18_reg>;
+ SPKVDDR-supply = <&ldo18_reg>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt
deleted file mode 100644
index 49028a4f5df1..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-samsung.txt
+++ /dev/null
@@ -1,122 +0,0 @@
-* Samsung SPI Controller
-
-The Samsung SPI controller is used to interface with various devices such as flash
-and display controllers using the SPI communication interface.
-
-Required SoC Specific Properties:
-
-- compatible: should be one of the following.
- - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
- - samsung,s3c6410-spi: for s3c6410 platforms
- - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
- - samsung,exynos5433-spi: for exynos5433 compatible controllers
- - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED>
-
-- reg: physical base address of the controller and length of memory mapped
- region.
-
-- interrupts: The interrupt number to the cpu. The interrupt specifier format
- depends on the interrupt controller.
-
-- dmas : Two or more DMA channel specifiers following the convention outlined
- in bindings/dma/dma.txt
-
-- dma-names: Names for the dma channels. There must be at least one channel
- named "tx" for transmit and named "rx" for receive.
-
-- clocks: specifies the clock IDs provided to the SPI controller; they are
- required for interacting with the controller itself, for synchronizing the bus
- and as I/O clock (the latter is required by exynos5433 and exynos7).
-
-- clock-names: string names of the clocks in the 'clocks' property; for all the
- the devices the names must be "spi", "spi_busclkN" (where N is determined by
- "samsung,spi-src-clk"), while Exynos5433 should specify a third clock
- "spi_ioclk" for the I/O clock.
-
-Required Board Specific Properties:
-
-- #address-cells: should be 1.
-- #size-cells: should be 0.
-
-Optional Board Specific Properties:
-
-- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
- select the clock source for the spi bus clock, this property can be used to
- indicate the clock to be used for driving the spi bus clock. If not specified,
- the clock number 0 is used as default.
-
-- num-cs: Specifies the number of chip select lines supported. If
- not specified, the default number of chip select lines is set to 1.
-
-- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)
-
-- no-cs-readback: the CS line is disconnected, therefore the device should not
- operate based on CS signalling.
-
-SPI Controller specific data in SPI slave nodes:
-
-- The spi slave nodes should provide the following information which is required
- by the spi controller.
-
- - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
- miso line (to account for any lag in the miso line). The following are the
- valid values.
-
- - 0: No phase shift.
- - 1: 90 degree phase shift sampling.
- - 2: 180 degree phase shift sampling.
- - 3: 270 degree phase shift sampling.
-
-Aliases:
-
-- All the SPI controller nodes should be represented in the aliases node using
- the following format 'spi{n}' where n is a unique number for the alias.
-
-
-Example:
-
-- SoC Specific Portion:
-
- spi_0: spi@12d20000 {
- compatible = "samsung,exynos4210-spi";
- reg = <0x12d20000 0x100>;
- interrupts = <0 66 0>;
- dmas = <&pdma0 5
- &pdma0 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
-- Board Specific Portion:
-
- spi_0: spi@12d20000 {
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_bus>;
- cs-gpios = <&gpa2 5 0>;
-
- w25q80bw@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "w25x80";
- reg = <0>;
- spi-max-frequency = <10000>;
-
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
-
- partition@0 {
- label = "U-Boot";
- reg = <0x0 0x40000>;
- read-only;
- };
-
- partition@40000 {
- label = "Kernel";
- reg = <0x40000 0xc0000>;
- };
- };
- };
diff --git a/MAINTAINERS b/MAINTAINERS
index af392bd04874..572eb97f1855 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17058,7 +17058,7 @@ M: Andi Shyti <andi@etezian.org>
L: linux-spi@vger.kernel.org
L: linux-samsung-soc@vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/spi/spi-samsung.txt
+F: Documentation/devicetree/bindings/spi/samsung,spi.yaml
F: drivers/spi/spi-s3c*
F: include/linux/platform_data/spi-s3c64xx.h
F: include/linux/spi/s3c24xx-fiq.h
--
2.32.0
^ permalink raw reply related [flat|nested] 14+ messages in thread
* [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
@ 2022-01-02 15:58 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-02 15:58 UTC (permalink / raw)
To: Krzysztof Kozlowski, Andi Shyti, Mark Brown, Rob Herring,
linux-spi, linux-samsung-soc, devicetree, linux-kernel,
linux-arm-kernel
Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
controller bindings to DT schema format
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
---
.../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
.../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
MAINTAINERS | 2 +-
3 files changed, 221 insertions(+), 123 deletions(-)
create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
new file mode 100644
index 000000000000..195bfafe05fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
@@ -0,0 +1,220 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung S3C/S5P/Exynos SoC SPI controller
+
+maintainers:
+ - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description:
+ All the SPI controller nodes should be represented in the aliases node using
+ the following format 'spi{n}' where n is a unique number for the alias.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - samsung,s3c2443-spi
+ - samsung,s3c6410-spi
+ - samsung,s5pv210-spi
+ - samsung,exynos5433-spi
+ - const: samsung,exynos7-spi
+ deprecated: true
+
+ clocks:
+ minItems: 2
+ maxItems: 3
+
+ clock-names:
+ minItems: 2
+ maxItems: 3
+
+ cs-gpios: true
+
+ dmas:
+ minItems: 2
+ maxItems: 2
+
+ dma-names:
+ items:
+ - const: tx
+ - const: rx
+
+ interrupts:
+ maxItems: 1
+
+ no-cs-readback:
+ description:
+ The CS line is disconnected, therefore the device should not operate
+ based on CS signalling.
+ type: boolean
+
+ num-cs:
+ minimum: 1
+ maximum: 4
+ default: 1
+
+ samsung,spi-src-clk:
+ description:
+ If the spi controller includes a internal clock mux to select the clock
+ source for the spi bus clock, this property can be used to indicate the
+ clock to be used for driving the spi bus clock. If not specified, the
+ clock number 0 is used as default.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ default: 0
+
+ reg:
+ maxItems: 1
+
+patternProperties:
+ "^.*@[0-9a-f]+$":
+ type: object
+
+ allOf:
+ - $ref: spi-peripheral-props.yaml
+
+ properties:
+ controller-data:
+ type: object
+ additionalProperties: false
+
+ properties:
+ samsung,spi-feedback-delay:
+ description: |
+ The sampling phase shift to be applied on the miso line (to account
+ for any lag in the miso line). Valid values:
+ - 0: No phase shift.
+ - 1: 90 degree phase shift sampling.
+ - 2: 180 degree phase shift sampling.
+ - 3: 270 degree phase shift sampling.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [0, 1, 2, 3]
+
+ required:
+ - samsung,spi-feedback-delay
+
+ required:
+ - controller-data
+
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - clocks
+ - clock-names
+ - dmas
+ - dma-names
+ - interrupts
+ - reg
+
+allOf:
+ - $ref: spi-controller.yaml#
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: samsung,exynos5433-spi
+ then:
+ properties:
+ clocks:
+ minItems: 3
+ maxItems: 3
+ clock-names:
+ items:
+ - const: spi
+ - enum:
+ - spi_busclk0
+ - spi_busclk1
+ - spi_busclk2
+ - spi_busclk3
+ - const: spi_ioclk
+ else:
+ properties:
+ clocks:
+ minItems: 2
+ maxItems: 2
+ clock-names:
+ items:
+ - const: spi
+ - enum:
+ - spi_busclk0
+ - spi_busclk1
+ - spi_busclk2
+ - spi_busclk3
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/exynos5433.h>
+ #include <dt-bindings/clock/samsung,s2mps11.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ spi@14d30000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d30000 0x100>;
+ interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&pdma0 11>, <&pdma0 10>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
+ clock-names = "spi",
+ "spi_busclk0",
+ "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ num-cs = <1>;
+
+ cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ audio-codec@0 {
+ compatible = "wlf,wm5110";
+ reg = <0x0>;
+ spi-max-frequency = <20000000>;
+ interrupt-parent = <&gpa0>;
+ interrupts = <4 IRQ_TYPE_NONE>;
+ clocks = <&pmu_system_controller 0>,
+ <&s2mps13_osc S2MPS11_CLK_BT>;
+ clock-names = "mclk1", "mclk2";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ wlf,micd-detect-debounce = <300>;
+ wlf,micd-bias-start-time = <0x1>;
+ wlf,micd-rate = <0x7>;
+ wlf,micd-dbtime = <0x2>;
+ wlf,micd-force-micbias;
+ wlf,micd-configs = <0x0 1 0>;
+ wlf,hpdet-channel = <1>;
+ wlf,gpsw = <0x1>;
+ wlf,inmode = <2 0 2 0>;
+
+ wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
+ wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
+
+ /* core supplies */
+ AVDD-supply = <&ldo18_reg>;
+ DBVDD1-supply = <&ldo18_reg>;
+ CPVDD-supply = <&ldo18_reg>;
+ DBVDD2-supply = <&ldo18_reg>;
+ DBVDD3-supply = <&ldo18_reg>;
+ SPKVDDL-supply = <&ldo18_reg>;
+ SPKVDDR-supply = <&ldo18_reg>;
+
+ controller-data {
+ samsung,spi-feedback-delay = <0>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt
deleted file mode 100644
index 49028a4f5df1..000000000000
--- a/Documentation/devicetree/bindings/spi/spi-samsung.txt
+++ /dev/null
@@ -1,122 +0,0 @@
-* Samsung SPI Controller
-
-The Samsung SPI controller is used to interface with various devices such as flash
-and display controllers using the SPI communication interface.
-
-Required SoC Specific Properties:
-
-- compatible: should be one of the following.
- - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
- - samsung,s3c6410-spi: for s3c6410 platforms
- - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
- - samsung,exynos5433-spi: for exynos5433 compatible controllers
- - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED>
-
-- reg: physical base address of the controller and length of memory mapped
- region.
-
-- interrupts: The interrupt number to the cpu. The interrupt specifier format
- depends on the interrupt controller.
-
-- dmas : Two or more DMA channel specifiers following the convention outlined
- in bindings/dma/dma.txt
-
-- dma-names: Names for the dma channels. There must be at least one channel
- named "tx" for transmit and named "rx" for receive.
-
-- clocks: specifies the clock IDs provided to the SPI controller; they are
- required for interacting with the controller itself, for synchronizing the bus
- and as I/O clock (the latter is required by exynos5433 and exynos7).
-
-- clock-names: string names of the clocks in the 'clocks' property; for all the
- the devices the names must be "spi", "spi_busclkN" (where N is determined by
- "samsung,spi-src-clk"), while Exynos5433 should specify a third clock
- "spi_ioclk" for the I/O clock.
-
-Required Board Specific Properties:
-
-- #address-cells: should be 1.
-- #size-cells: should be 0.
-
-Optional Board Specific Properties:
-
-- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
- select the clock source for the spi bus clock, this property can be used to
- indicate the clock to be used for driving the spi bus clock. If not specified,
- the clock number 0 is used as default.
-
-- num-cs: Specifies the number of chip select lines supported. If
- not specified, the default number of chip select lines is set to 1.
-
-- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)
-
-- no-cs-readback: the CS line is disconnected, therefore the device should not
- operate based on CS signalling.
-
-SPI Controller specific data in SPI slave nodes:
-
-- The spi slave nodes should provide the following information which is required
- by the spi controller.
-
- - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
- miso line (to account for any lag in the miso line). The following are the
- valid values.
-
- - 0: No phase shift.
- - 1: 90 degree phase shift sampling.
- - 2: 180 degree phase shift sampling.
- - 3: 270 degree phase shift sampling.
-
-Aliases:
-
-- All the SPI controller nodes should be represented in the aliases node using
- the following format 'spi{n}' where n is a unique number for the alias.
-
-
-Example:
-
-- SoC Specific Portion:
-
- spi_0: spi@12d20000 {
- compatible = "samsung,exynos4210-spi";
- reg = <0x12d20000 0x100>;
- interrupts = <0 66 0>;
- dmas = <&pdma0 5
- &pdma0 4>;
- dma-names = "tx", "rx";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
-- Board Specific Portion:
-
- spi_0: spi@12d20000 {
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_bus>;
- cs-gpios = <&gpa2 5 0>;
-
- w25q80bw@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "w25x80";
- reg = <0>;
- spi-max-frequency = <10000>;
-
- controller-data {
- samsung,spi-feedback-delay = <0>;
- };
-
- partition@0 {
- label = "U-Boot";
- reg = <0x0 0x40000>;
- read-only;
- };
-
- partition@40000 {
- label = "Kernel";
- reg = <0x40000 0xc0000>;
- };
- };
- };
diff --git a/MAINTAINERS b/MAINTAINERS
index af392bd04874..572eb97f1855 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17058,7 +17058,7 @@ M: Andi Shyti <andi@etezian.org>
L: linux-spi@vger.kernel.org
L: linux-samsung-soc@vger.kernel.org
S: Maintained
-F: Documentation/devicetree/bindings/spi/spi-samsung.txt
+F: Documentation/devicetree/bindings/spi/samsung,spi.yaml
F: drivers/spi/spi-s3c*
F: include/linux/platform_data/spi-s3c64xx.h
F: include/linux/spi/s3c24xx-fiq.h
--
2.32.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 14+ messages in thread
* Re: [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250
2022-01-02 15:58 ` Krzysztof Kozlowski
@ 2022-01-03 9:40 ` Andi Shyti
-1 siblings, 0 replies; 14+ messages in thread
From: Andi Shyti @ 2022-01-03 9:40 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
Hi Krzysztof,
On Sun, Jan 02, 2022 at 04:58:06PM +0100, Krzysztof Kozlowski wrote:
> "dmas" property should be rather an array of phandles, as dtschema
> points.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Thanks,
Andi
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250
@ 2022-01-03 9:40 ` Andi Shyti
0 siblings, 0 replies; 14+ messages in thread
From: Andi Shyti @ 2022-01-03 9:40 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
Hi Krzysztof,
On Sun, Jan 02, 2022 at 04:58:06PM +0100, Krzysztof Kozlowski wrote:
> "dmas" property should be rather an array of phandles, as dtschema
> points.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Andi Shyti <andi@etezian.org>
Thanks,
Andi
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
2022-01-02 15:58 ` Krzysztof Kozlowski
@ 2022-01-03 14:41 ` Sam Protsenko
-1 siblings, 0 replies; 14+ messages in thread
From: Sam Protsenko @ 2022-01-03 14:41 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
On Sun, 2 Jan 2022 at 17:58, Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
>
> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
> controller bindings to DT schema format
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> ---
> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
> MAINTAINERS | 2 +-
> 3 files changed, 221 insertions(+), 123 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> new file mode 100644
> index 000000000000..195bfafe05fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> @@ -0,0 +1,220 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung S3C/S5P/Exynos SoC SPI controller
> +
> +maintainers:
> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> +
> +description:
> + All the SPI controller nodes should be represented in the aliases node using
> + the following format 'spi{n}' where n is a unique number for the alias.
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - samsung,s3c2443-spi
Maybe add the list of supported platforms for each compatible (in a
comment on the same line), like it was done in .txt binding?
Other than that:
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
> + - samsung,s3c6410-spi
> + - samsung,s5pv210-spi
> + - samsung,exynos5433-spi
> + - const: samsung,exynos7-spi
> + deprecated: true
> +
> + clocks:
> + minItems: 2
> + maxItems: 3
> +
> + clock-names:
> + minItems: 2
> + maxItems: 3
> +
> + cs-gpios: true
> +
> + dmas:
> + minItems: 2
> + maxItems: 2
> +
> + dma-names:
> + items:
> + - const: tx
> + - const: rx
> +
> + interrupts:
> + maxItems: 1
> +
> + no-cs-readback:
> + description:
> + The CS line is disconnected, therefore the device should not operate
> + based on CS signalling.
> + type: boolean
> +
> + num-cs:
> + minimum: 1
> + maximum: 4
> + default: 1
> +
> + samsung,spi-src-clk:
> + description:
> + If the spi controller includes a internal clock mux to select the clock
> + source for the spi bus clock, this property can be used to indicate the
> + clock to be used for driving the spi bus clock. If not specified, the
> + clock number 0 is used as default.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + reg:
> + maxItems: 1
> +
> +patternProperties:
> + "^.*@[0-9a-f]+$":
> + type: object
> +
> + allOf:
> + - $ref: spi-peripheral-props.yaml
> +
> + properties:
> + controller-data:
> + type: object
> + additionalProperties: false
> +
> + properties:
> + samsung,spi-feedback-delay:
> + description: |
> + The sampling phase shift to be applied on the miso line (to account
> + for any lag in the miso line). Valid values:
> + - 0: No phase shift.
> + - 1: 90 degree phase shift sampling.
> + - 2: 180 degree phase shift sampling.
> + - 3: 270 degree phase shift sampling.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - samsung,spi-feedback-delay
> +
> + required:
> + - controller-data
> +
> + unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - dmas
> + - dma-names
> + - interrupts
> + - reg
> +
> +allOf:
> + - $ref: spi-controller.yaml#
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: samsung,exynos5433-spi
> + then:
> + properties:
> + clocks:
> + minItems: 3
> + maxItems: 3
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> + - const: spi_ioclk
> + else:
> + properties:
> + clocks:
> + minItems: 2
> + maxItems: 2
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/exynos5433.h>
> + #include <dt-bindings/clock/samsung,s2mps11.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + spi@14d30000 {
> + compatible = "samsung,exynos5433-spi";
> + reg = <0x14d30000 0x100>;
> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&pdma0 11>, <&pdma0 10>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
> + clock-names = "spi",
> + "spi_busclk0",
> + "spi_ioclk";
> + samsung,spi-src-clk = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_bus>;
> + num-cs = <1>;
> +
> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + audio-codec@0 {
> + compatible = "wlf,wm5110";
> + reg = <0x0>;
> + spi-max-frequency = <20000000>;
> + interrupt-parent = <&gpa0>;
> + interrupts = <4 IRQ_TYPE_NONE>;
> + clocks = <&pmu_system_controller 0>,
> + <&s2mps13_osc S2MPS11_CLK_BT>;
> + clock-names = "mclk1", "mclk2";
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + wlf,micd-detect-debounce = <300>;
> + wlf,micd-bias-start-time = <0x1>;
> + wlf,micd-rate = <0x7>;
> + wlf,micd-dbtime = <0x2>;
> + wlf,micd-force-micbias;
> + wlf,micd-configs = <0x0 1 0>;
> + wlf,hpdet-channel = <1>;
> + wlf,gpsw = <0x1>;
> + wlf,inmode = <2 0 2 0>;
> +
> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
> +
> + /* core supplies */
> + AVDD-supply = <&ldo18_reg>;
> + DBVDD1-supply = <&ldo18_reg>;
> + CPVDD-supply = <&ldo18_reg>;
> + DBVDD2-supply = <&ldo18_reg>;
> + DBVDD3-supply = <&ldo18_reg>;
> + SPKVDDL-supply = <&ldo18_reg>;
> + SPKVDDR-supply = <&ldo18_reg>;
> +
> + controller-data {
> + samsung,spi-feedback-delay = <0>;
> + };
> + };
> + };
> diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt
> deleted file mode 100644
> index 49028a4f5df1..000000000000
> --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt
> +++ /dev/null
> @@ -1,122 +0,0 @@
> -* Samsung SPI Controller
> -
> -The Samsung SPI controller is used to interface with various devices such as flash
> -and display controllers using the SPI communication interface.
> -
> -Required SoC Specific Properties:
> -
> -- compatible: should be one of the following.
> - - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
> - - samsung,s3c6410-spi: for s3c6410 platforms
> - - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
> - - samsung,exynos5433-spi: for exynos5433 compatible controllers
> - - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED>
> -
> -- reg: physical base address of the controller and length of memory mapped
> - region.
> -
> -- interrupts: The interrupt number to the cpu. The interrupt specifier format
> - depends on the interrupt controller.
> -
> -- dmas : Two or more DMA channel specifiers following the convention outlined
> - in bindings/dma/dma.txt
> -
> -- dma-names: Names for the dma channels. There must be at least one channel
> - named "tx" for transmit and named "rx" for receive.
> -
> -- clocks: specifies the clock IDs provided to the SPI controller; they are
> - required for interacting with the controller itself, for synchronizing the bus
> - and as I/O clock (the latter is required by exynos5433 and exynos7).
> -
> -- clock-names: string names of the clocks in the 'clocks' property; for all the
> - the devices the names must be "spi", "spi_busclkN" (where N is determined by
> - "samsung,spi-src-clk"), while Exynos5433 should specify a third clock
> - "spi_ioclk" for the I/O clock.
> -
> -Required Board Specific Properties:
> -
> -- #address-cells: should be 1.
> -- #size-cells: should be 0.
> -
> -Optional Board Specific Properties:
> -
> -- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
> - select the clock source for the spi bus clock, this property can be used to
> - indicate the clock to be used for driving the spi bus clock. If not specified,
> - the clock number 0 is used as default.
> -
> -- num-cs: Specifies the number of chip select lines supported. If
> - not specified, the default number of chip select lines is set to 1.
> -
> -- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)
> -
> -- no-cs-readback: the CS line is disconnected, therefore the device should not
> - operate based on CS signalling.
> -
> -SPI Controller specific data in SPI slave nodes:
> -
> -- The spi slave nodes should provide the following information which is required
> - by the spi controller.
> -
> - - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
> - miso line (to account for any lag in the miso line). The following are the
> - valid values.
> -
> - - 0: No phase shift.
> - - 1: 90 degree phase shift sampling.
> - - 2: 180 degree phase shift sampling.
> - - 3: 270 degree phase shift sampling.
> -
> -Aliases:
> -
> -- All the SPI controller nodes should be represented in the aliases node using
> - the following format 'spi{n}' where n is a unique number for the alias.
> -
> -
> -Example:
> -
> -- SoC Specific Portion:
> -
> - spi_0: spi@12d20000 {
> - compatible = "samsung,exynos4210-spi";
> - reg = <0x12d20000 0x100>;
> - interrupts = <0 66 0>;
> - dmas = <&pdma0 5
> - &pdma0 4>;
> - dma-names = "tx", "rx";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> -- Board Specific Portion:
> -
> - spi_0: spi@12d20000 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_bus>;
> - cs-gpios = <&gpa2 5 0>;
> -
> - w25q80bw@0 {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "w25x80";
> - reg = <0>;
> - spi-max-frequency = <10000>;
> -
> - controller-data {
> - samsung,spi-feedback-delay = <0>;
> - };
> -
> - partition@0 {
> - label = "U-Boot";
> - reg = <0x0 0x40000>;
> - read-only;
> - };
> -
> - partition@40000 {
> - label = "Kernel";
> - reg = <0x40000 0xc0000>;
> - };
> - };
> - };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index af392bd04874..572eb97f1855 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17058,7 +17058,7 @@ M: Andi Shyti <andi@etezian.org>
> L: linux-spi@vger.kernel.org
> L: linux-samsung-soc@vger.kernel.org
> S: Maintained
> -F: Documentation/devicetree/bindings/spi/spi-samsung.txt
> +F: Documentation/devicetree/bindings/spi/samsung,spi.yaml
> F: drivers/spi/spi-s3c*
> F: include/linux/platform_data/spi-s3c64xx.h
> F: include/linux/spi/s3c24xx-fiq.h
> --
> 2.32.0
>
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
@ 2022-01-03 14:41 ` Sam Protsenko
0 siblings, 0 replies; 14+ messages in thread
From: Sam Protsenko @ 2022-01-03 14:41 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
On Sun, 2 Jan 2022 at 17:58, Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
>
> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
> controller bindings to DT schema format
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> ---
> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
> MAINTAINERS | 2 +-
> 3 files changed, 221 insertions(+), 123 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> new file mode 100644
> index 000000000000..195bfafe05fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> @@ -0,0 +1,220 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung S3C/S5P/Exynos SoC SPI controller
> +
> +maintainers:
> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> +
> +description:
> + All the SPI controller nodes should be represented in the aliases node using
> + the following format 'spi{n}' where n is a unique number for the alias.
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - samsung,s3c2443-spi
Maybe add the list of supported platforms for each compatible (in a
comment on the same line), like it was done in .txt binding?
Other than that:
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
> + - samsung,s3c6410-spi
> + - samsung,s5pv210-spi
> + - samsung,exynos5433-spi
> + - const: samsung,exynos7-spi
> + deprecated: true
> +
> + clocks:
> + minItems: 2
> + maxItems: 3
> +
> + clock-names:
> + minItems: 2
> + maxItems: 3
> +
> + cs-gpios: true
> +
> + dmas:
> + minItems: 2
> + maxItems: 2
> +
> + dma-names:
> + items:
> + - const: tx
> + - const: rx
> +
> + interrupts:
> + maxItems: 1
> +
> + no-cs-readback:
> + description:
> + The CS line is disconnected, therefore the device should not operate
> + based on CS signalling.
> + type: boolean
> +
> + num-cs:
> + minimum: 1
> + maximum: 4
> + default: 1
> +
> + samsung,spi-src-clk:
> + description:
> + If the spi controller includes a internal clock mux to select the clock
> + source for the spi bus clock, this property can be used to indicate the
> + clock to be used for driving the spi bus clock. If not specified, the
> + clock number 0 is used as default.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + reg:
> + maxItems: 1
> +
> +patternProperties:
> + "^.*@[0-9a-f]+$":
> + type: object
> +
> + allOf:
> + - $ref: spi-peripheral-props.yaml
> +
> + properties:
> + controller-data:
> + type: object
> + additionalProperties: false
> +
> + properties:
> + samsung,spi-feedback-delay:
> + description: |
> + The sampling phase shift to be applied on the miso line (to account
> + for any lag in the miso line). Valid values:
> + - 0: No phase shift.
> + - 1: 90 degree phase shift sampling.
> + - 2: 180 degree phase shift sampling.
> + - 3: 270 degree phase shift sampling.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - samsung,spi-feedback-delay
> +
> + required:
> + - controller-data
> +
> + unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - dmas
> + - dma-names
> + - interrupts
> + - reg
> +
> +allOf:
> + - $ref: spi-controller.yaml#
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: samsung,exynos5433-spi
> + then:
> + properties:
> + clocks:
> + minItems: 3
> + maxItems: 3
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> + - const: spi_ioclk
> + else:
> + properties:
> + clocks:
> + minItems: 2
> + maxItems: 2
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/exynos5433.h>
> + #include <dt-bindings/clock/samsung,s2mps11.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + spi@14d30000 {
> + compatible = "samsung,exynos5433-spi";
> + reg = <0x14d30000 0x100>;
> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&pdma0 11>, <&pdma0 10>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
> + clock-names = "spi",
> + "spi_busclk0",
> + "spi_ioclk";
> + samsung,spi-src-clk = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_bus>;
> + num-cs = <1>;
> +
> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> +
> + audio-codec@0 {
> + compatible = "wlf,wm5110";
> + reg = <0x0>;
> + spi-max-frequency = <20000000>;
> + interrupt-parent = <&gpa0>;
> + interrupts = <4 IRQ_TYPE_NONE>;
> + clocks = <&pmu_system_controller 0>,
> + <&s2mps13_osc S2MPS11_CLK_BT>;
> + clock-names = "mclk1", "mclk2";
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + wlf,micd-detect-debounce = <300>;
> + wlf,micd-bias-start-time = <0x1>;
> + wlf,micd-rate = <0x7>;
> + wlf,micd-dbtime = <0x2>;
> + wlf,micd-force-micbias;
> + wlf,micd-configs = <0x0 1 0>;
> + wlf,hpdet-channel = <1>;
> + wlf,gpsw = <0x1>;
> + wlf,inmode = <2 0 2 0>;
> +
> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
> +
> + /* core supplies */
> + AVDD-supply = <&ldo18_reg>;
> + DBVDD1-supply = <&ldo18_reg>;
> + CPVDD-supply = <&ldo18_reg>;
> + DBVDD2-supply = <&ldo18_reg>;
> + DBVDD3-supply = <&ldo18_reg>;
> + SPKVDDL-supply = <&ldo18_reg>;
> + SPKVDDR-supply = <&ldo18_reg>;
> +
> + controller-data {
> + samsung,spi-feedback-delay = <0>;
> + };
> + };
> + };
> diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt
> deleted file mode 100644
> index 49028a4f5df1..000000000000
> --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt
> +++ /dev/null
> @@ -1,122 +0,0 @@
> -* Samsung SPI Controller
> -
> -The Samsung SPI controller is used to interface with various devices such as flash
> -and display controllers using the SPI communication interface.
> -
> -Required SoC Specific Properties:
> -
> -- compatible: should be one of the following.
> - - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
> - - samsung,s3c6410-spi: for s3c6410 platforms
> - - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
> - - samsung,exynos5433-spi: for exynos5433 compatible controllers
> - - samsung,exynos7-spi: for exynos7 platforms <DEPRECATED>
> -
> -- reg: physical base address of the controller and length of memory mapped
> - region.
> -
> -- interrupts: The interrupt number to the cpu. The interrupt specifier format
> - depends on the interrupt controller.
> -
> -- dmas : Two or more DMA channel specifiers following the convention outlined
> - in bindings/dma/dma.txt
> -
> -- dma-names: Names for the dma channels. There must be at least one channel
> - named "tx" for transmit and named "rx" for receive.
> -
> -- clocks: specifies the clock IDs provided to the SPI controller; they are
> - required for interacting with the controller itself, for synchronizing the bus
> - and as I/O clock (the latter is required by exynos5433 and exynos7).
> -
> -- clock-names: string names of the clocks in the 'clocks' property; for all the
> - the devices the names must be "spi", "spi_busclkN" (where N is determined by
> - "samsung,spi-src-clk"), while Exynos5433 should specify a third clock
> - "spi_ioclk" for the I/O clock.
> -
> -Required Board Specific Properties:
> -
> -- #address-cells: should be 1.
> -- #size-cells: should be 0.
> -
> -Optional Board Specific Properties:
> -
> -- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
> - select the clock source for the spi bus clock, this property can be used to
> - indicate the clock to be used for driving the spi bus clock. If not specified,
> - the clock number 0 is used as default.
> -
> -- num-cs: Specifies the number of chip select lines supported. If
> - not specified, the default number of chip select lines is set to 1.
> -
> -- cs-gpios: should specify GPIOs used for chipselects (see spi-bus.txt)
> -
> -- no-cs-readback: the CS line is disconnected, therefore the device should not
> - operate based on CS signalling.
> -
> -SPI Controller specific data in SPI slave nodes:
> -
> -- The spi slave nodes should provide the following information which is required
> - by the spi controller.
> -
> - - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
> - miso line (to account for any lag in the miso line). The following are the
> - valid values.
> -
> - - 0: No phase shift.
> - - 1: 90 degree phase shift sampling.
> - - 2: 180 degree phase shift sampling.
> - - 3: 270 degree phase shift sampling.
> -
> -Aliases:
> -
> -- All the SPI controller nodes should be represented in the aliases node using
> - the following format 'spi{n}' where n is a unique number for the alias.
> -
> -
> -Example:
> -
> -- SoC Specific Portion:
> -
> - spi_0: spi@12d20000 {
> - compatible = "samsung,exynos4210-spi";
> - reg = <0x12d20000 0x100>;
> - interrupts = <0 66 0>;
> - dmas = <&pdma0 5
> - &pdma0 4>;
> - dma-names = "tx", "rx";
> - #address-cells = <1>;
> - #size-cells = <0>;
> - };
> -
> -- Board Specific Portion:
> -
> - spi_0: spi@12d20000 {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&spi0_bus>;
> - cs-gpios = <&gpa2 5 0>;
> -
> - w25q80bw@0 {
> - #address-cells = <1>;
> - #size-cells = <1>;
> - compatible = "w25x80";
> - reg = <0>;
> - spi-max-frequency = <10000>;
> -
> - controller-data {
> - samsung,spi-feedback-delay = <0>;
> - };
> -
> - partition@0 {
> - label = "U-Boot";
> - reg = <0x0 0x40000>;
> - read-only;
> - };
> -
> - partition@40000 {
> - label = "Kernel";
> - reg = <0x40000 0xc0000>;
> - };
> - };
> - };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index af392bd04874..572eb97f1855 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -17058,7 +17058,7 @@ M: Andi Shyti <andi@etezian.org>
> L: linux-spi@vger.kernel.org
> L: linux-samsung-soc@vger.kernel.org
> S: Maintained
> -F: Documentation/devicetree/bindings/spi/spi-samsung.txt
> +F: Documentation/devicetree/bindings/spi/samsung,spi.yaml
> F: drivers/spi/spi-s3c*
> F: include/linux/platform_data/spi-s3c64xx.h
> F: include/linux/spi/s3c24xx-fiq.h
> --
> 2.32.0
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
2022-01-02 15:58 ` Krzysztof Kozlowski
@ 2022-01-04 16:47 ` Rob Herring
-1 siblings, 0 replies; 14+ messages in thread
From: Rob Herring @ 2022-01-04 16:47 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, linux-spi, linux-samsung-soc, devicetree,
linux-kernel, linux-arm-kernel
On Sun, Jan 02, 2022 at 04:58:07PM +0100, Krzysztof Kozlowski wrote:
> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
> controller bindings to DT schema format
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> ---
> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
> MAINTAINERS | 2 +-
> 3 files changed, 221 insertions(+), 123 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> new file mode 100644
> index 000000000000..195bfafe05fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> @@ -0,0 +1,220 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung S3C/S5P/Exynos SoC SPI controller
> +
> +maintainers:
> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> +
> +description:
> + All the SPI controller nodes should be represented in the aliases node using
> + the following format 'spi{n}' where n is a unique number for the alias.
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - samsung,s3c2443-spi
> + - samsung,s3c6410-spi
> + - samsung,s5pv210-spi
> + - samsung,exynos5433-spi
> + - const: samsung,exynos7-spi
> + deprecated: true
> +
> + clocks:
> + minItems: 2
> + maxItems: 3
> +
> + clock-names:
> + minItems: 2
> + maxItems: 3
> +
> + cs-gpios: true
> +
> + dmas:
> + minItems: 2
> + maxItems: 2
> +
> + dma-names:
> + items:
> + - const: tx
> + - const: rx
> +
> + interrupts:
> + maxItems: 1
> +
> + no-cs-readback:
> + description:
> + The CS line is disconnected, therefore the device should not operate
> + based on CS signalling.
> + type: boolean
> +
> + num-cs:
> + minimum: 1
> + maximum: 4
> + default: 1
> +
> + samsung,spi-src-clk:
> + description:
> + If the spi controller includes a internal clock mux to select the clock
> + source for the spi bus clock, this property can be used to indicate the
> + clock to be used for driving the spi bus clock. If not specified, the
> + clock number 0 is used as default.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + reg:
> + maxItems: 1
> +
> +patternProperties:
> + "^.*@[0-9a-f]+$":
> + type: object
> +
> + allOf:
> + - $ref: spi-peripheral-props.yaml
> +
> + properties:
> + controller-data:
> + type: object
> + additionalProperties: false
> +
> + properties:
> + samsung,spi-feedback-delay:
All this has to go in it's own schema which then needs to be added to
spi-peripheral-props.yaml.
> + description: |
> + The sampling phase shift to be applied on the miso line (to account
> + for any lag in the miso line). Valid values:
> + - 0: No phase shift.
> + - 1: 90 degree phase shift sampling.
> + - 2: 180 degree phase shift sampling.
> + - 3: 270 degree phase shift sampling.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - samsung,spi-feedback-delay
> +
> + required:
> + - controller-data
Not really great that this is required and there's not some default that
works.
> +
> + unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - dmas
> + - dma-names
> + - interrupts
> + - reg
> +
> +allOf:
> + - $ref: spi-controller.yaml#
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: samsung,exynos5433-spi
> + then:
> + properties:
> + clocks:
> + minItems: 3
> + maxItems: 3
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> + - const: spi_ioclk
> + else:
> + properties:
> + clocks:
> + minItems: 2
> + maxItems: 2
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/exynos5433.h>
> + #include <dt-bindings/clock/samsung,s2mps11.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + spi@14d30000 {
> + compatible = "samsung,exynos5433-spi";
> + reg = <0x14d30000 0x100>;
> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&pdma0 11>, <&pdma0 10>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
> + clock-names = "spi",
> + "spi_busclk0",
> + "spi_ioclk";
> + samsung,spi-src-clk = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_bus>;
> + num-cs = <1>;
> +
> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
> + status = "okay";
Don't need 'status' in examples.
> + audio-codec@0 {
> + compatible = "wlf,wm5110";
> + reg = <0x0>;
> + spi-max-frequency = <20000000>;
> + interrupt-parent = <&gpa0>;
> + interrupts = <4 IRQ_TYPE_NONE>;
> + clocks = <&pmu_system_controller 0>,
> + <&s2mps13_osc S2MPS11_CLK_BT>;
> + clock-names = "mclk1", "mclk2";
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + wlf,micd-detect-debounce = <300>;
> + wlf,micd-bias-start-time = <0x1>;
> + wlf,micd-rate = <0x7>;
> + wlf,micd-dbtime = <0x2>;
> + wlf,micd-force-micbias;
> + wlf,micd-configs = <0x0 1 0>;
> + wlf,hpdet-channel = <1>;
> + wlf,gpsw = <0x1>;
> + wlf,inmode = <2 0 2 0>;
> +
> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
> +
> + /* core supplies */
> + AVDD-supply = <&ldo18_reg>;
> + DBVDD1-supply = <&ldo18_reg>;
> + CPVDD-supply = <&ldo18_reg>;
> + DBVDD2-supply = <&ldo18_reg>;
> + DBVDD3-supply = <&ldo18_reg>;
> + SPKVDDL-supply = <&ldo18_reg>;
> + SPKVDDR-supply = <&ldo18_reg>;
> +
> + controller-data {
The schema didn't get checked since spi-peripheral-props.yaml isn't
yet in my tree, but I'd expect this to be a warning. If not its schema
needs to be a bit stricter. The schema for "wlf,wm5110" will need to
reference spi-peripheral-props.yaml. (Actually, all SPI peripheral
device schemas will need a reference in theory, but really we only care
for devices used with controllers with extra properties).
Rob
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
@ 2022-01-04 16:47 ` Rob Herring
0 siblings, 0 replies; 14+ messages in thread
From: Rob Herring @ 2022-01-04 16:47 UTC (permalink / raw)
To: Krzysztof Kozlowski
Cc: Andi Shyti, Mark Brown, linux-spi, linux-samsung-soc, devicetree,
linux-kernel, linux-arm-kernel
On Sun, Jan 02, 2022 at 04:58:07PM +0100, Krzysztof Kozlowski wrote:
> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
> controller bindings to DT schema format
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> ---
> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
> MAINTAINERS | 2 +-
> 3 files changed, 221 insertions(+), 123 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>
> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> new file mode 100644
> index 000000000000..195bfafe05fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
> @@ -0,0 +1,220 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Samsung S3C/S5P/Exynos SoC SPI controller
> +
> +maintainers:
> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
> +
> +description:
> + All the SPI controller nodes should be represented in the aliases node using
> + the following format 'spi{n}' where n is a unique number for the alias.
> +
> +properties:
> + compatible:
> + oneOf:
> + - enum:
> + - samsung,s3c2443-spi
> + - samsung,s3c6410-spi
> + - samsung,s5pv210-spi
> + - samsung,exynos5433-spi
> + - const: samsung,exynos7-spi
> + deprecated: true
> +
> + clocks:
> + minItems: 2
> + maxItems: 3
> +
> + clock-names:
> + minItems: 2
> + maxItems: 3
> +
> + cs-gpios: true
> +
> + dmas:
> + minItems: 2
> + maxItems: 2
> +
> + dma-names:
> + items:
> + - const: tx
> + - const: rx
> +
> + interrupts:
> + maxItems: 1
> +
> + no-cs-readback:
> + description:
> + The CS line is disconnected, therefore the device should not operate
> + based on CS signalling.
> + type: boolean
> +
> + num-cs:
> + minimum: 1
> + maximum: 4
> + default: 1
> +
> + samsung,spi-src-clk:
> + description:
> + If the spi controller includes a internal clock mux to select the clock
> + source for the spi bus clock, this property can be used to indicate the
> + clock to be used for driving the spi bus clock. If not specified, the
> + clock number 0 is used as default.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + default: 0
> +
> + reg:
> + maxItems: 1
> +
> +patternProperties:
> + "^.*@[0-9a-f]+$":
> + type: object
> +
> + allOf:
> + - $ref: spi-peripheral-props.yaml
> +
> + properties:
> + controller-data:
> + type: object
> + additionalProperties: false
> +
> + properties:
> + samsung,spi-feedback-delay:
All this has to go in it's own schema which then needs to be added to
spi-peripheral-props.yaml.
> + description: |
> + The sampling phase shift to be applied on the miso line (to account
> + for any lag in the miso line). Valid values:
> + - 0: No phase shift.
> + - 1: 90 degree phase shift sampling.
> + - 2: 180 degree phase shift sampling.
> + - 3: 270 degree phase shift sampling.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - samsung,spi-feedback-delay
> +
> + required:
> + - controller-data
Not really great that this is required and there's not some default that
works.
> +
> + unevaluatedProperties: false
> +
> +required:
> + - compatible
> + - clocks
> + - clock-names
> + - dmas
> + - dma-names
> + - interrupts
> + - reg
> +
> +allOf:
> + - $ref: spi-controller.yaml#
> + - if:
> + properties:
> + compatible:
> + contains:
> + const: samsung,exynos5433-spi
> + then:
> + properties:
> + clocks:
> + minItems: 3
> + maxItems: 3
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> + - const: spi_ioclk
> + else:
> + properties:
> + clocks:
> + minItems: 2
> + maxItems: 2
> + clock-names:
> + items:
> + - const: spi
> + - enum:
> + - spi_busclk0
> + - spi_busclk1
> + - spi_busclk2
> + - spi_busclk3
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/clock/exynos5433.h>
> + #include <dt-bindings/clock/samsung,s2mps11.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> + #include <dt-bindings/gpio/gpio.h>
> +
> + spi@14d30000 {
> + compatible = "samsung,exynos5433-spi";
> + reg = <0x14d30000 0x100>;
> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
> + dmas = <&pdma0 11>, <&pdma0 10>;
> + dma-names = "tx", "rx";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_SPI1>,
> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
> + clock-names = "spi",
> + "spi_busclk0",
> + "spi_ioclk";
> + samsung,spi-src-clk = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_bus>;
> + num-cs = <1>;
> +
> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
> + status = "okay";
Don't need 'status' in examples.
> + audio-codec@0 {
> + compatible = "wlf,wm5110";
> + reg = <0x0>;
> + spi-max-frequency = <20000000>;
> + interrupt-parent = <&gpa0>;
> + interrupts = <4 IRQ_TYPE_NONE>;
> + clocks = <&pmu_system_controller 0>,
> + <&s2mps13_osc S2MPS11_CLK_BT>;
> + clock-names = "mclk1", "mclk2";
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + wlf,micd-detect-debounce = <300>;
> + wlf,micd-bias-start-time = <0x1>;
> + wlf,micd-rate = <0x7>;
> + wlf,micd-dbtime = <0x2>;
> + wlf,micd-force-micbias;
> + wlf,micd-configs = <0x0 1 0>;
> + wlf,hpdet-channel = <1>;
> + wlf,gpsw = <0x1>;
> + wlf,inmode = <2 0 2 0>;
> +
> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
> +
> + /* core supplies */
> + AVDD-supply = <&ldo18_reg>;
> + DBVDD1-supply = <&ldo18_reg>;
> + CPVDD-supply = <&ldo18_reg>;
> + DBVDD2-supply = <&ldo18_reg>;
> + DBVDD3-supply = <&ldo18_reg>;
> + SPKVDDL-supply = <&ldo18_reg>;
> + SPKVDDR-supply = <&ldo18_reg>;
> +
> + controller-data {
The schema didn't get checked since spi-peripheral-props.yaml isn't
yet in my tree, but I'd expect this to be a warning. If not its schema
needs to be a bit stricter. The schema for "wlf,wm5110" will need to
reference spi-peripheral-props.yaml. (Actually, all SPI peripheral
device schemas will need a reference in theory, but really we only care
for devices used with controllers with extra properties).
Rob
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
2022-01-03 14:41 ` Sam Protsenko
@ 2022-01-10 15:10 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-10 15:10 UTC (permalink / raw)
To: Sam Protsenko
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
On 03/01/2022 15:41, Sam Protsenko wrote:
> On Sun, 2 Jan 2022 at 17:58, Krzysztof Kozlowski
> <krzysztof.kozlowski@canonical.com> wrote:
>>
>> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
>> controller bindings to DT schema format
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> ---
>> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
>> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
>> MAINTAINERS | 2 +-
>> 3 files changed, 221 insertions(+), 123 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>>
>> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> new file mode 100644
>> index 000000000000..195bfafe05fd
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> @@ -0,0 +1,220 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Samsung S3C/S5P/Exynos SoC SPI controller
>> +
>> +maintainers:
>> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> +
>> +description:
>> + All the SPI controller nodes should be represented in the aliases node using
>> + the following format 'spi{n}' where n is a unique number for the alias.
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - enum:
>> + - samsung,s3c2443-spi
>
> Maybe add the list of supported platforms for each compatible (in a
> comment on the same line), like it was done in .txt binding?
>
> Other than that:
>
Sure.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
@ 2022-01-10 15:10 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-10 15:10 UTC (permalink / raw)
To: Sam Protsenko
Cc: Andi Shyti, Mark Brown, Rob Herring, linux-spi,
linux-samsung-soc, devicetree, linux-kernel, linux-arm-kernel
On 03/01/2022 15:41, Sam Protsenko wrote:
> On Sun, 2 Jan 2022 at 17:58, Krzysztof Kozlowski
> <krzysztof.kozlowski@canonical.com> wrote:
>>
>> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
>> controller bindings to DT schema format
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> ---
>> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
>> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
>> MAINTAINERS | 2 +-
>> 3 files changed, 221 insertions(+), 123 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>>
>> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> new file mode 100644
>> index 000000000000..195bfafe05fd
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> @@ -0,0 +1,220 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Samsung S3C/S5P/Exynos SoC SPI controller
>> +
>> +maintainers:
>> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> +
>> +description:
>> + All the SPI controller nodes should be represented in the aliases node using
>> + the following format 'spi{n}' where n is a unique number for the alias.
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - enum:
>> + - samsung,s3c2443-spi
>
> Maybe add the list of supported platforms for each compatible (in a
> comment on the same line), like it was done in .txt binding?
>
> Other than that:
>
Sure.
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
2022-01-04 16:47 ` Rob Herring
@ 2022-01-10 15:52 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-10 15:52 UTC (permalink / raw)
To: Rob Herring
Cc: Andi Shyti, Mark Brown, linux-spi, linux-samsung-soc, devicetree,
linux-kernel, linux-arm-kernel
On 04/01/2022 17:47, Rob Herring wrote:
> On Sun, Jan 02, 2022 at 04:58:07PM +0100, Krzysztof Kozlowski wrote:
>> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
>> controller bindings to DT schema format
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> ---
>> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
>> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
>> MAINTAINERS | 2 +-
>> 3 files changed, 221 insertions(+), 123 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>>
>> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> new file mode 100644
>> index 000000000000..195bfafe05fd
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> @@ -0,0 +1,220 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Samsung S3C/S5P/Exynos SoC SPI controller
>> +
>> +maintainers:
>> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> +
>> +description:
>> + All the SPI controller nodes should be represented in the aliases node using
>> + the following format 'spi{n}' where n is a unique number for the alias.
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - enum:
>> + - samsung,s3c2443-spi
>> + - samsung,s3c6410-spi
>> + - samsung,s5pv210-spi
>> + - samsung,exynos5433-spi
>> + - const: samsung,exynos7-spi
>> + deprecated: true
>> +
>> + clocks:
>> + minItems: 2
>> + maxItems: 3
>> +
>> + clock-names:
>> + minItems: 2
>> + maxItems: 3
>> +
>> + cs-gpios: true
>> +
>> + dmas:
>> + minItems: 2
>> + maxItems: 2
>> +
>> + dma-names:
>> + items:
>> + - const: tx
>> + - const: rx
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + no-cs-readback:
>> + description:
>> + The CS line is disconnected, therefore the device should not operate
>> + based on CS signalling.
>> + type: boolean
>> +
>> + num-cs:
>> + minimum: 1
>> + maximum: 4
>> + default: 1
>> +
>> + samsung,spi-src-clk:
>> + description:
>> + If the spi controller includes a internal clock mux to select the clock
>> + source for the spi bus clock, this property can be used to indicate the
>> + clock to be used for driving the spi bus clock. If not specified, the
>> + clock number 0 is used as default.
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + default: 0
>> +
>> + reg:
>> + maxItems: 1
>> +
>> +patternProperties:
>> + "^.*@[0-9a-f]+$":
>> + type: object
>> +
>> + allOf:
>> + - $ref: spi-peripheral-props.yaml
>> +
>> + properties:
>> + controller-data:
>> + type: object
>> + additionalProperties: false
>> +
>> + properties:
>> + samsung,spi-feedback-delay:
>
> All this has to go in it's own schema which then needs to be added to
> spi-peripheral-props.yaml.
OK
>
>> + description: |
>> + The sampling phase shift to be applied on the miso line (to account
>> + for any lag in the miso line). Valid values:
>> + - 0: No phase shift.
>> + - 1: 90 degree phase shift sampling.
>> + - 2: 180 degree phase shift sampling.
>> + - 3: 270 degree phase shift sampling.
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + enum: [0, 1, 2, 3]
>> +
>> + required:
>> + - samsung,spi-feedback-delay
>> +
>> + required:
>> + - controller-data
>
> Not really great that this is required and there's not some default that
> works.
I can make it optional with new kernel. I'll send a follow up patch for
this.
>
>> +
>> + unevaluatedProperties: false
>> +
>> +required:
>> + - compatible
>> + - clocks
>> + - clock-names
>> + - dmas
>> + - dma-names
>> + - interrupts
>> + - reg
>> +
>> +allOf:
>> + - $ref: spi-controller.yaml#
>> + - if:
>> + properties:
>> + compatible:
>> + contains:
>> + const: samsung,exynos5433-spi
>> + then:
>> + properties:
>> + clocks:
>> + minItems: 3
>> + maxItems: 3
>> + clock-names:
>> + items:
>> + - const: spi
>> + - enum:
>> + - spi_busclk0
>> + - spi_busclk1
>> + - spi_busclk2
>> + - spi_busclk3
>> + - const: spi_ioclk
>> + else:
>> + properties:
>> + clocks:
>> + minItems: 2
>> + maxItems: 2
>> + clock-names:
>> + items:
>> + - const: spi
>> + - enum:
>> + - spi_busclk0
>> + - spi_busclk1
>> + - spi_busclk2
>> + - spi_busclk3
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/exynos5433.h>
>> + #include <dt-bindings/clock/samsung,s2mps11.h>
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/gpio/gpio.h>
>> +
>> + spi@14d30000 {
>> + compatible = "samsung,exynos5433-spi";
>> + reg = <0x14d30000 0x100>;
>> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
>> + dmas = <&pdma0 11>, <&pdma0 10>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
>> + <&cmu_peric CLK_SCLK_SPI1>,
>> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
>> + clock-names = "spi",
>> + "spi_busclk0",
>> + "spi_ioclk";
>> + samsung,spi-src-clk = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi1_bus>;
>> + num-cs = <1>;
>> +
>> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
>> + status = "okay";
>
> Don't need 'status' in examples.
Sure
>
>> + audio-codec@0 {
>> + compatible = "wlf,wm5110";
>> + reg = <0x0>;
>> + spi-max-frequency = <20000000>;
>> + interrupt-parent = <&gpa0>;
>> + interrupts = <4 IRQ_TYPE_NONE>;
>> + clocks = <&pmu_system_controller 0>,
>> + <&s2mps13_osc S2MPS11_CLK_BT>;
>> + clock-names = "mclk1", "mclk2";
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + wlf,micd-detect-debounce = <300>;
>> + wlf,micd-bias-start-time = <0x1>;
>> + wlf,micd-rate = <0x7>;
>> + wlf,micd-dbtime = <0x2>;
>> + wlf,micd-force-micbias;
>> + wlf,micd-configs = <0x0 1 0>;
>> + wlf,hpdet-channel = <1>;
>> + wlf,gpsw = <0x1>;
>> + wlf,inmode = <2 0 2 0>;
>> +
>> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
>> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
>> +
>> + /* core supplies */
>> + AVDD-supply = <&ldo18_reg>;
>> + DBVDD1-supply = <&ldo18_reg>;
>> + CPVDD-supply = <&ldo18_reg>;
>> + DBVDD2-supply = <&ldo18_reg>;
>> + DBVDD3-supply = <&ldo18_reg>;
>> + SPKVDDL-supply = <&ldo18_reg>;
>> + SPKVDDR-supply = <&ldo18_reg>;
>> +
>> + controller-data {
>
> The schema didn't get checked since spi-peripheral-props.yaml isn't
> yet in my tree, but I'd expect this to be a warning. If not its schema
> needs to be a bit stricter. The schema for "wlf,wm5110" will need to
> reference spi-peripheral-props.yaml. (Actually, all SPI peripheral
> device schemas will need a reference in theory, but really we only care
> for devices used with controllers with extra properties).
I did not see any warnings. I'll modify the wm5110.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 14+ messages in thread
* Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
@ 2022-01-10 15:52 ` Krzysztof Kozlowski
0 siblings, 0 replies; 14+ messages in thread
From: Krzysztof Kozlowski @ 2022-01-10 15:52 UTC (permalink / raw)
To: Rob Herring
Cc: Andi Shyti, Mark Brown, linux-spi, linux-samsung-soc, devicetree,
linux-kernel, linux-arm-kernel
On 04/01/2022 17:47, Rob Herring wrote:
> On Sun, Jan 02, 2022 at 04:58:07PM +0100, Krzysztof Kozlowski wrote:
>> Convert the Samsung SoC (S3C24xx, S3C64xx, S5Pv210, Exynos) SPI
>> controller bindings to DT schema format
>>
>> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> ---
>> .../devicetree/bindings/spi/samsung,spi.yaml | 220 ++++++++++++++++++
>> .../devicetree/bindings/spi/spi-samsung.txt | 122 ----------
>> MAINTAINERS | 2 +-
>> 3 files changed, 221 insertions(+), 123 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> delete mode 100644 Documentation/devicetree/bindings/spi/spi-samsung.txt
>>
>> diff --git a/Documentation/devicetree/bindings/spi/samsung,spi.yaml b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> new file mode 100644
>> index 000000000000..195bfafe05fd
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/spi/samsung,spi.yaml
>> @@ -0,0 +1,220 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/spi/samsung,spi.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Samsung S3C/S5P/Exynos SoC SPI controller
>> +
>> +maintainers:
>> + - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
>> +
>> +description:
>> + All the SPI controller nodes should be represented in the aliases node using
>> + the following format 'spi{n}' where n is a unique number for the alias.
>> +
>> +properties:
>> + compatible:
>> + oneOf:
>> + - enum:
>> + - samsung,s3c2443-spi
>> + - samsung,s3c6410-spi
>> + - samsung,s5pv210-spi
>> + - samsung,exynos5433-spi
>> + - const: samsung,exynos7-spi
>> + deprecated: true
>> +
>> + clocks:
>> + minItems: 2
>> + maxItems: 3
>> +
>> + clock-names:
>> + minItems: 2
>> + maxItems: 3
>> +
>> + cs-gpios: true
>> +
>> + dmas:
>> + minItems: 2
>> + maxItems: 2
>> +
>> + dma-names:
>> + items:
>> + - const: tx
>> + - const: rx
>> +
>> + interrupts:
>> + maxItems: 1
>> +
>> + no-cs-readback:
>> + description:
>> + The CS line is disconnected, therefore the device should not operate
>> + based on CS signalling.
>> + type: boolean
>> +
>> + num-cs:
>> + minimum: 1
>> + maximum: 4
>> + default: 1
>> +
>> + samsung,spi-src-clk:
>> + description:
>> + If the spi controller includes a internal clock mux to select the clock
>> + source for the spi bus clock, this property can be used to indicate the
>> + clock to be used for driving the spi bus clock. If not specified, the
>> + clock number 0 is used as default.
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + default: 0
>> +
>> + reg:
>> + maxItems: 1
>> +
>> +patternProperties:
>> + "^.*@[0-9a-f]+$":
>> + type: object
>> +
>> + allOf:
>> + - $ref: spi-peripheral-props.yaml
>> +
>> + properties:
>> + controller-data:
>> + type: object
>> + additionalProperties: false
>> +
>> + properties:
>> + samsung,spi-feedback-delay:
>
> All this has to go in it's own schema which then needs to be added to
> spi-peripheral-props.yaml.
OK
>
>> + description: |
>> + The sampling phase shift to be applied on the miso line (to account
>> + for any lag in the miso line). Valid values:
>> + - 0: No phase shift.
>> + - 1: 90 degree phase shift sampling.
>> + - 2: 180 degree phase shift sampling.
>> + - 3: 270 degree phase shift sampling.
>> + $ref: /schemas/types.yaml#/definitions/uint32
>> + enum: [0, 1, 2, 3]
>> +
>> + required:
>> + - samsung,spi-feedback-delay
>> +
>> + required:
>> + - controller-data
>
> Not really great that this is required and there's not some default that
> works.
I can make it optional with new kernel. I'll send a follow up patch for
this.
>
>> +
>> + unevaluatedProperties: false
>> +
>> +required:
>> + - compatible
>> + - clocks
>> + - clock-names
>> + - dmas
>> + - dma-names
>> + - interrupts
>> + - reg
>> +
>> +allOf:
>> + - $ref: spi-controller.yaml#
>> + - if:
>> + properties:
>> + compatible:
>> + contains:
>> + const: samsung,exynos5433-spi
>> + then:
>> + properties:
>> + clocks:
>> + minItems: 3
>> + maxItems: 3
>> + clock-names:
>> + items:
>> + - const: spi
>> + - enum:
>> + - spi_busclk0
>> + - spi_busclk1
>> + - spi_busclk2
>> + - spi_busclk3
>> + - const: spi_ioclk
>> + else:
>> + properties:
>> + clocks:
>> + minItems: 2
>> + maxItems: 2
>> + clock-names:
>> + items:
>> + - const: spi
>> + - enum:
>> + - spi_busclk0
>> + - spi_busclk1
>> + - spi_busclk2
>> + - spi_busclk3
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> + - |
>> + #include <dt-bindings/clock/exynos5433.h>
>> + #include <dt-bindings/clock/samsung,s2mps11.h>
>> + #include <dt-bindings/interrupt-controller/arm-gic.h>
>> + #include <dt-bindings/gpio/gpio.h>
>> +
>> + spi@14d30000 {
>> + compatible = "samsung,exynos5433-spi";
>> + reg = <0x14d30000 0x100>;
>> + interrupts = <GIC_SPI 433 IRQ_TYPE_LEVEL_HIGH>;
>> + dmas = <&pdma0 11>, <&pdma0 10>;
>> + dma-names = "tx", "rx";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&cmu_peric CLK_PCLK_SPI1>,
>> + <&cmu_peric CLK_SCLK_SPI1>,
>> + <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
>> + clock-names = "spi",
>> + "spi_busclk0",
>> + "spi_ioclk";
>> + samsung,spi-src-clk = <0>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&spi1_bus>;
>> + num-cs = <1>;
>> +
>> + cs-gpios = <&gpd6 3 GPIO_ACTIVE_HIGH>;
>> + status = "okay";
>
> Don't need 'status' in examples.
Sure
>
>> + audio-codec@0 {
>> + compatible = "wlf,wm5110";
>> + reg = <0x0>;
>> + spi-max-frequency = <20000000>;
>> + interrupt-parent = <&gpa0>;
>> + interrupts = <4 IRQ_TYPE_NONE>;
>> + clocks = <&pmu_system_controller 0>,
>> + <&s2mps13_osc S2MPS11_CLK_BT>;
>> + clock-names = "mclk1", "mclk2";
>> +
>> + gpio-controller;
>> + #gpio-cells = <2>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + wlf,micd-detect-debounce = <300>;
>> + wlf,micd-bias-start-time = <0x1>;
>> + wlf,micd-rate = <0x7>;
>> + wlf,micd-dbtime = <0x2>;
>> + wlf,micd-force-micbias;
>> + wlf,micd-configs = <0x0 1 0>;
>> + wlf,hpdet-channel = <1>;
>> + wlf,gpsw = <0x1>;
>> + wlf,inmode = <2 0 2 0>;
>> +
>> + wlf,reset = <&gpc0 7 GPIO_ACTIVE_HIGH>;
>> + wlf,ldoena = <&gpf0 0 GPIO_ACTIVE_HIGH>;
>> +
>> + /* core supplies */
>> + AVDD-supply = <&ldo18_reg>;
>> + DBVDD1-supply = <&ldo18_reg>;
>> + CPVDD-supply = <&ldo18_reg>;
>> + DBVDD2-supply = <&ldo18_reg>;
>> + DBVDD3-supply = <&ldo18_reg>;
>> + SPKVDDL-supply = <&ldo18_reg>;
>> + SPKVDDR-supply = <&ldo18_reg>;
>> +
>> + controller-data {
>
> The schema didn't get checked since spi-peripheral-props.yaml isn't
> yet in my tree, but I'd expect this to be a warning. If not its schema
> needs to be a bit stricter. The schema for "wlf,wm5110" will need to
> reference spi-peripheral-props.yaml. (Actually, all SPI peripheral
> device schemas will need a reference in theory, but really we only care
> for devices used with controllers with extra properties).
I did not see any warnings. I'll modify the wm5110.
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2022-01-10 15:58 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-01-02 15:58 [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250 Krzysztof Kozlowski
2022-01-02 15:58 ` Krzysztof Kozlowski
2022-01-02 15:58 ` [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema Krzysztof Kozlowski
2022-01-02 15:58 ` Krzysztof Kozlowski
2022-01-03 14:41 ` Sam Protsenko
2022-01-03 14:41 ` Sam Protsenko
2022-01-10 15:10 ` Krzysztof Kozlowski
2022-01-10 15:10 ` Krzysztof Kozlowski
2022-01-04 16:47 ` Rob Herring
2022-01-04 16:47 ` Rob Herring
2022-01-10 15:52 ` Krzysztof Kozlowski
2022-01-10 15:52 ` Krzysztof Kozlowski
2022-01-03 9:40 ` [PATCH 1/2] ARM: dts: exynos: split dmas into array of phandles in Exynos5250 Andi Shyti
2022-01-03 9:40 ` Andi Shyti
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.