From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: X-Spam-Checker-Version: SpamAssassin 3.4.0 (2014-02-07) on aws-us-west-2-korg-lkml-1.web.codeaurora.org Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by smtp.lore.kernel.org (Postfix) with ESMTP id 2627AC433EF for ; Mon, 21 Feb 2022 11:39:13 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1356536AbiBULje (ORCPT ); Mon, 21 Feb 2022 06:39:34 -0500 Received: from mxb-00190b01.gslb.pphosted.com ([23.128.96.19]:59062 "EHLO lindbergh.monkeyblade.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S231761AbiBULjd (ORCPT ); Mon, 21 Feb 2022 06:39:33 -0500 Received: from relay4-d.mail.gandi.net (relay4-d.mail.gandi.net [217.70.183.196]) by lindbergh.monkeyblade.net (Postfix) with ESMTPS id A6ABE1ADA7 for ; Mon, 21 Feb 2022 03:39:09 -0800 (PST) Received: (Authenticated sender: jacopo@jmondi.org) by mail.gandi.net (Postfix) with ESMTPSA id 93C88E0009; Mon, 21 Feb 2022 11:39:04 +0000 (UTC) Date: Mon, 21 Feb 2022 12:39:03 +0100 From: Jacopo Mondi To: Laurent Pinchart Cc: Steve Longerbeam , sakari.ailus@iki.fi, hverkuil-cisco@xs4all.nl, mirela.rabulea@nxp.com, xavier.roumegue@oss.nxp.com, tomi.valkeinen@ideasonboard.com, hugues.fruchet@st.com, prabhakar.mahadev-lad.rj@bp.renesas.com, aford173@gmail.com, festevam@gmail.com, Eugen.Hristev@microchip.com, jbrunet@baylibre.com, Mauro Carvalho Chehab , linux-media@vger.kernel.org Subject: Re: [PATCH v2 07/23] media: ov5640: Rework CSI-2 clock tree Message-ID: <20220221113903.msstecnvjn7xrimq@uno.localdomain> References: <20220210110458.152494-1-jacopo@jmondi.org> <20220210110458.152494-8-jacopo@jmondi.org> MIME-Version: 1.0 Content-Type: text/plain; charset=utf-8 Content-Disposition: inline In-Reply-To: Precedence: bulk List-ID: X-Mailing-List: linux-media@vger.kernel.org Hi Laurent On Sun, Feb 20, 2022 at 02:17:12PM +0200, Laurent Pinchart wrote: > Hi Jacopo, > > Thank you for the patch. > > On Thu, Feb 10, 2022 at 12:04:42PM +0100, Jacopo Mondi wrote: > > Re-work the ov5640_set_mipi_pclk() function to calculate the > > PLL configuration using the pixel_rate and link_freq values set at > > s_fmt time. > > > > Rework the DVP clock mode settings to calculate the pixel clock > > internally and remove the assumption on the 16bpp format. > > > > Tested in MIPI CSI-2 mode with 1 and 2 data lanes with: > > - all the sensor supported resolutions in UYVY and RGB565 formats. > > - resolutions >= 1280x720 in RAW Bayer format. > > - resolutions < 1280x720 in RGB888 format. > > > > Signed-off-by: Jacopo Mondi > > --- > > drivers/media/i2c/ov5640.c | 189 ++++++++++++++++++------------------- > > 1 file changed, 90 insertions(+), 99 deletions(-) > > > > diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c > > index 50b611697470..eb4789ae6abf 100644 > > --- a/drivers/media/i2c/ov5640.c > > +++ b/drivers/media/i2c/ov5640.c > > @@ -90,6 +90,7 @@ > > #define OV5640_REG_POLARITY_CTRL00 0x4740 > > #define OV5640_REG_MIPI_CTRL00 0x4800 > > #define OV5640_REG_DEBUG_MODE 0x4814 > > +#define OV5640_REG_PCLK_PERIOD 0x4837 > > #define OV5640_REG_ISP_FORMAT_MUX_CTRL 0x501f > > #define OV5640_REG_PRE_ISP_TEST_SET1 0x503d > > #define OV5640_REG_SDE_CTRL0 0x5580 > > @@ -922,20 +923,10 @@ static int ov5640_mod_reg(struct ov5640_dev *sensor, u16 reg, > > * +-----+-----+ > > * +------------> PCLK > > * > > - * This is deviating from the datasheet at least for the register > > - * 0x3108, since it's said here that the PCLK would be clocked from > > - * the PLL. > > - * > > - * There seems to be also (unverified) constraints: > > + * There seems to be also constraints: > > * - the PLL pre-divider output rate should be in the 4-27MHz range > > * - the PLL multiplier output rate should be in the 500-1000MHz range > > * - PCLK >= SCLK * 2 in YUV, >= SCLK in Raw or JPEG > > - * > > - * In the two latter cases, these constraints are met since our > > - * factors are hardcoded. If we were to change that, we would need to > > - * take this into account. The only varying parts are the PLL > > - * multiplier and the system clock divider, which are shared between > > - * all these clocks so won't cause any issue. > > */ > > > > /* > > @@ -954,13 +945,6 @@ static int ov5640_mod_reg(struct ov5640_dev *sensor, u16 reg, > > #define OV5640_SYSDIV_MIN 1 > > #define OV5640_SYSDIV_MAX 16 > > > > -/* > > - * Hardcode these values for scaler and non-scaler modes. > > - * FIXME: to be re-calcualted for 1 data lanes setups > > - */ > > -#define OV5640_MIPI_DIV_PCLK 2 > > -#define OV5640_MIPI_DIV_SCLK 1 > > - > > /* > > * This is supposed to be ranging from 1 to 2, but the value is always > > * set to 2 in the vendor kernels. > > @@ -1071,69 +1055,77 @@ static unsigned long ov5640_calc_sys_clk(struct ov5640_dev *sensor, > > * ov5640_set_mipi_pclk() - Calculate the clock tree configuration values > > * for the MIPI CSI-2 output. > > * > > - * @rate: The requested bandwidth per lane in bytes per second. > > - * 'Bandwidth Per Lane' is calculated as: > > - * bpl = HTOT * VTOT * FPS * bpp / num_lanes; > > - * > > - * This function use the requested bandwidth to calculate: > > - * - sample_rate = bpl / (bpp / num_lanes); > > - * = bpl / (PLL_RDIV * BIT_DIV * PCLK_DIV * MIPI_DIV / num_lanes); > > - * > > - * - mipi_sclk = bpl / MIPI_DIV / 2; ( / 2 is for CSI-2 DDR) > > - * > > - * with these fixed parameters: > > - * PLL_RDIV = 2; > > - * BIT_DIVIDER = 2; (MIPI_BIT_MODE == 8 ? 2 : 2,5); > > - * PCLK_DIV = 1; > > - * > > - * The MIPI clock generation differs for modes that use the scaler and modes > > - * that do not. In case the scaler is in use, the MIPI_SCLK generates the MIPI > > - * BIT CLk, and thus: > > - * > > - * - mipi_sclk = bpl / MIPI_DIV / 2; > > - * MIPI_DIV = 1; > > - * > > - * For modes that do not go through the scaler, the MIPI BIT CLOCK is generated > > - * from the pixel clock, and thus: > > - * > > - * - sample_rate = bpl / (bpp / num_lanes); > > - * = bpl / (2 * 2 * 1 * MIPI_DIV / num_lanes); > > - * = bpl / (4 * MIPI_DIV / num_lanes); > > - * - MIPI_DIV = bpp / (4 * num_lanes); > > - * > > - * FIXME: this have been tested with 16bpp and 2 lanes setup only. > > - * MIPI_DIV is fixed to value 2, but it -might- be changed according to the > > - * above formula for setups with 1 lane or image formats with different bpp. > > - * > > - * FIXME: this deviates from the sensor manual documentation which is quite > > - * thin on the MIPI clock tree generation part. > > + * FIXME: tested with 2 lanes only. > > Not true anymore, is it ? > Yes, I can drop this > > */ > > -static int ov5640_set_mipi_pclk(struct ov5640_dev *sensor, > > - unsigned long rate) > > +static int ov5640_set_mipi_pclk(struct ov5640_dev *sensor) > > { > > - const struct ov5640_mode_info *mode = sensor->current_mode; > > + u8 bit_div, mipi_div, p_div, sclk_div, sclk2x_div, root_div; > > + struct v4l2_mbus_framefmt *fmt = &sensor->fmt; > > u8 prediv, mult, sysdiv; > > - u8 mipi_div; > > + unsigned long sysclk; > > + unsigned long sample_rate; > > + u8 pclk_period; > > + s64 link_freq; > > int ret; > > > > + /* Use the link frequency computed at ov5640_update_pixel_rate() time. */ > > + link_freq = ov5640_csi2_link_freqs[sensor->ctrls.link_freq->cur.val]; > > + > > /* > > - * 1280x720 is reported to use 'SUBSAMPLING' only, > > - * but according to the sensor manual it goes through the > > - * scaler before subsampling. > > + * - mipi_div - Additional divider for the MIPI lane clock. > > + * > > + * Higher link frequencies would make sysclk > 1GHz. > > + * Keep the sysclk low and do not divide in the MIPI domain. > > */ > > - if (mode->dn_mode == SCALING || > > - (mode->id == OV5640_MODE_720P_1280_720)) > > - mipi_div = OV5640_MIPI_DIV_SCLK; > > + if (link_freq > OV5640_LINK_RATE_MAX) > > + mipi_div = 1; > > else > > - mipi_div = OV5640_MIPI_DIV_PCLK; > > + mipi_div = 2; > > > > - ov5640_calc_sys_clk(sensor, rate, &prediv, &mult, &sysdiv); > > + sysclk = link_freq * mipi_div; > > + ov5640_calc_sys_clk(sensor, sysclk, &prediv, &mult, &sysdiv); > > > > - ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL0, > > - 0x0f, OV5640_PLL_CTRL0_MIPI_MODE_8BIT); > > + /* > > + * Adjust PLL parameters to maintain the MIPI_SCLK-to-PCLK ratio; > > s/;/:/ ? > > > + * > > + * - root_div = 2 (fixed) > > + * - bit_div : MIPI 8-bit = 2 > > + * MIPI 10-bit = 2.5 > > + * - p_div = 1 (fixed) > > + * - pll_div = (2 lanes ? mipi_div : 2 * mipi_div) > > There's no pll_div variable in the code, nothing called "PLL div" in > comments, and nothing in the datasheet either as far as I can tell. > Based on your reply to the v1 review, I think you mean "p_div" instead > of "pll_div". Also, you mentioned there that P_DIV is equal to Yeah it's P_DIV > > - 1 data lane = MIPI_DIV (0x3035[3:0]) > - 2 data lane = 2 * MIPI_DIV > > while here you write the opposite. MIPI_DIV * number data lanes seems > more logical to me, as the CSI-2 clock frequency should be lower with > more data lanes. You could thus write > > * - p_div is set by the sensor to mipi_div * number of data lanes > > Let's add a blank line here, and > > * > * This results in the following MIPI_SCLK depending on the number > * of lanes: > * I said so as I got the same reasoning: more lanes = lower pclk freq But the PLL diagram where I got that comment from says P_DIV = mipi2lanes ? r03035[3:0] : 2*r3035[3:0] Should I assume a typo in the (found on the internet, never really confirmed) PLL clock diagram ? Actually being this the pixel clock divider, and being the pixel clock fed from the sysclk that feed the MIPI clk as well, doesn't it make sense to have a faster pixel clock when 2 lanes are available to be capable of reaching higher pixel rates ? Thing is that this register automatically takes a value, so might it be a protection to guarantee that with 1 data lane the pixels are clocked out slow enough for the CSI-2 bus to cope ? > > > + * 2 lanes: MIPI_SCLK = (4 or 5) * PCLK > > + * 1 lanes: MIPI_SCLK = (8 or 10) * PCLK > > + */ > > + root_div = OV5640_PLL_CTRL3_PLL_ROOT_DIV_2; > > + bit_div = OV5640_PLL_CTRL0_MIPI_MODE_8BIT; > > + p_div = OV5640_PLL_SYS_ROOT_DIVIDER_BYPASS; > > > > - ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL1, > > - 0xff, sysdiv << 4 | mipi_div); > > + /* > > + * Scaler clock: > > + * - YUV: PCLK >= 2 * SCLK > > + * - RAW or JPEG: PCLK >= SCLK > > + * - sclk2x_div = sclk_div / 2 > > + * > > + * TODO: test with JPEG. > > + */ > > + sclk_div = ilog2(OV5640_SCLK_ROOT_DIV); > > + sclk2x_div = ilog2(OV5640_SCLK2X_ROOT_DIV); > > + > > + /* > > + * Set the sample period expressed in ns with 1-bit decimal > > + * (0x01=0.5ns). > > + */ > > + sample_rate = ov5640_pixel_rates[sensor->current_mode->pixel_rate] > > + * (ov5640_code_to_bpp(fmt->code) / 8); > > + pclk_period = 2000000000U / sample_rate; > > + > > + /* Program the clock tree registers. */ > > + ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL0, 0x0f, bit_div); > > + if (ret) > > + return ret; > > + > > + ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL1, 0xff, > > + (sysdiv << 4) | mipi_div); > > if (ret) > > return ret; > > > > @@ -1141,13 +1133,27 @@ static int ov5640_set_mipi_pclk(struct ov5640_dev *sensor, > > if (ret) > > return ret; > > > > - ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL3, > > - 0x1f, OV5640_PLL_CTRL3_PLL_ROOT_DIV_2 | prediv); > > + ret = ov5640_mod_reg(sensor, OV5640_REG_SC_PLL_CTRL3, 0x1f, > > + root_div | prediv); > > + if (ret) > > + return ret; > > + > > + ret = ov5640_mod_reg(sensor, OV5640_REG_SYS_ROOT_DIVIDER, 0x3f, > > + (p_div << 4) | (sclk2x_div << 2) | sclk_div); > > Bits 5:4 of this register are named "PCLK root divider" in the > datasheet. Can you rename the variable to pclk_div to match the clock > tree diagram in the driver that names it "PCLK Div" ? Another option > would be to name ie pclk_root_div and update the clock tree diagram > accordingly. The p_div mention in the comment above should be renamed > too. There already is a root_div, I would avoid repeating it. I'll go for pclk_div. > > > if (ret) > > return ret; > > > > - return ov5640_mod_reg(sensor, OV5640_REG_SYS_ROOT_DIVIDER, > > - 0x30, OV5640_PLL_SYS_ROOT_DIVIDER_BYPASS); > > + return ov5640_write_reg(sensor, OV5640_REG_PCLK_PERIOD, pclk_period); > > +} > > + > > +static u32 ov5640_calc_pixel_rate(struct ov5640_dev *sensor) > > +{ > > + u32 rate; > > + > > + rate = sensor->current_mode->vtot * sensor->current_mode->htot; > > + rate *= ov5640_framerates[sensor->current_fr]; > > + > > + return rate; > > } > > > > static unsigned long ov5640_calc_pclk(struct ov5640_dev *sensor, > > @@ -1167,11 +1173,16 @@ static unsigned long ov5640_calc_pclk(struct ov5640_dev *sensor, > > return _rate / *pll_rdiv / *bit_div / *pclk_div; > > } > > > > -static int ov5640_set_dvp_pclk(struct ov5640_dev *sensor, unsigned long rate) > > +static int ov5640_set_dvp_pclk(struct ov5640_dev *sensor) > > { > > u8 prediv, mult, sysdiv, pll_rdiv, bit_div, pclk_div; > > + u32 rate; > > int ret; > > > > + rate = ov5640_calc_pixel_rate(sensor); > > + rate *= ov5640_code_to_bpp(sensor->fmt.code); > > + rate /= sensor->ep.bus.parallel.bus_width; > > + > > ov5640_calc_pclk(sensor, rate, &prediv, &mult, &sysdiv, &pll_rdiv, > > &bit_div, &pclk_div); > > > > @@ -1696,16 +1707,6 @@ ov5640_find_mode(struct ov5640_dev *sensor, enum ov5640_frame_rate fr, > > return mode; > > } > > > > -static u64 ov5640_calc_pixel_rate(struct ov5640_dev *sensor) > > -{ > > - u64 rate; > > - > > - rate = sensor->current_mode->vtot * sensor->current_mode->htot; > > - rate *= ov5640_framerates[sensor->current_fr]; > > - > > - return rate; > > -} > > - > > /* > > * sensor changes between scaling and subsampling, go through > > * exposure calculation > > @@ -1887,7 +1888,6 @@ static int ov5640_set_mode(struct ov5640_dev *sensor) > > enum ov5640_downsize_mode dn_mode, orig_dn_mode; > > bool auto_gain = sensor->ctrls.auto_gain->val == 1; > > bool auto_exp = sensor->ctrls.auto_exp->val == V4L2_EXPOSURE_AUTO; > > - unsigned long rate; > > int ret; > > > > dn_mode = mode->dn_mode; > > @@ -1906,19 +1906,10 @@ static int ov5640_set_mode(struct ov5640_dev *sensor) > > goto restore_auto_gain; > > } > > > > - /* > > - * All the formats we support have 16 bits per pixel, seems to require > > - * the same rate than YUV, so we can just use 16 bpp all the time. > > - */ > > - rate = ov5640_calc_pixel_rate(sensor) * 16; > > - if (ov5640_is_csi2(sensor)) { > > - rate = rate / sensor->ep.bus.mipi_csi2.num_data_lanes; > > - ret = ov5640_set_mipi_pclk(sensor, rate); > > - } else { > > - rate = rate / sensor->ep.bus.parallel.bus_width; > > - ret = ov5640_set_dvp_pclk(sensor, rate); > > - } > > - > > + if (ov5640_is_csi2(sensor)) > > + ret = ov5640_set_mipi_pclk(sensor); > > + else > > + ret = ov5640_set_dvp_pclk(sensor); > > if (ret < 0) > > return 0; > > > > -- > Regards, > > Laurent Pinchart