* [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Hi everyone,
thanks for your feedback on v1.
Changes in v2:
* Acked-by: Rob Herring to PATCH 1
* Removed 'status' property for non-disabled devices in PATCH 2
* Removed superfluous blank lines in PATCH 2
* Removed doubled status = "disabled" in PATCH 2
* Moved 'chosen' node up in PATCH 2
* Removed unit-address for GPIO buttons in PATCH 2
* Removed internal (und unsupported) SPI device node in PATCH 2
* Removed QSPI flash partitions in PATCH 2
* Rename audio-codec node name in PATCH 2
Below is the summary from v1 which has not changed.
This patch series adds support for the TQ-Systems TQMa6ULx & TQMa6ULxL modules.
Admittedly the name can be confusing, so I'll explain in more detail.
TQMa6ULx [1] is the module series using i.MX6UL. The 'x' is a placeholder for
different variants which have a different µC. TQMa6UL1 is using MCIMX6G1 which
has some peripheries disabled, more about it below. TQMa6UL2 (and TQMa6UL3)
has a full feature set and are treated identical on Linux side.
TQMa6ULxL [2] is the LGA variant of TQMa6ULx with a differnt module PCB, but
still common parts. There is no variant using MCIMX6G1.
TQMa6ULLx [1] is identical to TQMa6ULx, but using an i.MX6ULL instead.
There is no TQMa6UL1L.
TQMa6ULLxL [2] is identical to TQMa6ULxL, but using an i.MX6ULL instead.
There is no TQMa6ULL1L.
There are also 2 different mainboards namely MBAa6ULx & MBa6ULxL ('x' here is
not a placeholder, but part of the name). MBAa6ULx is for non-LGA variants
TQMa6ULx & TQMa6ULLx, while MBa6ULxL is used for TQMa6ULxL & TQMa6ULLxL.
It is also possible to mount a TQMa6ULxL to MBa6ULx using an LGA adapter
providing the sockets.
TQMa6UL1 uses MCIMX6G1 which has FEC2, CAN2, CSI and LCDIF disabled by fuses.
This wouldn't be a problem at all, iff fec would support EPROBE_DEFER for
Ethernet PHYs on a different MDIO bus. Both PHYs are connected to the same MDIO
bus. This is not a proble, but as FEC2 has the lower base address than FEC1
it is probed first. For this reason the PHYs have to be attached to FEC2 or
things wont work. But exactly this breaks on TQMa6UL1 which has no FEC2 at all.
There is a suggestion for fec driver at [3] but without solution (yet).
This is the single reason there is a 'tq,imx6ul-tqma6ul1' compatible.
In order for things to work, the PHYs have to be deleted from fec2 & mdio
subnode and added to fec1 again.
Regardings the file structure there is a .dtsi file for
* common common parts on all 4 module variants (LGA & non-LGA, imx6ul & imx6ull):
imx6ul-tqma6ul-common.dtsi
* common to non-LGA variants only: imx6ul-tqma6ulx-common.dtsi
* common to LGA variants only: imx6ul-tqma6ulxl-common.dtsi
This is valid for both TQMa6ULx and TQMa6ULLx. To not introduce another file
name separation, 'imx6ul-' is the prefix for common parts for imx6ul as well
as imx6ull.
Best regards,
Alexander
[1] https://www.tq-group.com/de/produkte/tq-embedded/arm-architektur/tqma6ulx/
[2] https://www.tq-group.com/de/produkte/tq-embedded/arm-architektur/tqma6ulxl/
[3] https://lkml.org/lkml/2021/10/14/430
Alexander Stein (4):
ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
Matthias Schiffer (1):
dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
.../devicetree/bindings/arm/fsl.yaml | 37 ++
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi | 211 +++++++
arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts | 55 ++
arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi | 37 ++
arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi | 71 +++
.../arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi | 71 +++
arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi | 43 ++
.../arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi | 48 ++
.../boot/dts/imx6ull-tqma6ull2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi | 76 +++
.../boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi | 76 +++
arch/arm/boot/dts/mba6ulx.dtsi | 571 ++++++++++++++++++
16 files changed, 1361 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
create mode 100644 arch/arm/boot/dts/mba6ulx.dtsi
--
2.25.1
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Hi everyone,
thanks for your feedback on v1.
Changes in v2:
* Acked-by: Rob Herring to PATCH 1
* Removed 'status' property for non-disabled devices in PATCH 2
* Removed superfluous blank lines in PATCH 2
* Removed doubled status = "disabled" in PATCH 2
* Moved 'chosen' node up in PATCH 2
* Removed unit-address for GPIO buttons in PATCH 2
* Removed internal (und unsupported) SPI device node in PATCH 2
* Removed QSPI flash partitions in PATCH 2
* Rename audio-codec node name in PATCH 2
Below is the summary from v1 which has not changed.
This patch series adds support for the TQ-Systems TQMa6ULx & TQMa6ULxL modules.
Admittedly the name can be confusing, so I'll explain in more detail.
TQMa6ULx [1] is the module series using i.MX6UL. The 'x' is a placeholder for
different variants which have a different µC. TQMa6UL1 is using MCIMX6G1 which
has some peripheries disabled, more about it below. TQMa6UL2 (and TQMa6UL3)
has a full feature set and are treated identical on Linux side.
TQMa6ULxL [2] is the LGA variant of TQMa6ULx with a differnt module PCB, but
still common parts. There is no variant using MCIMX6G1.
TQMa6ULLx [1] is identical to TQMa6ULx, but using an i.MX6ULL instead.
There is no TQMa6UL1L.
TQMa6ULLxL [2] is identical to TQMa6ULxL, but using an i.MX6ULL instead.
There is no TQMa6ULL1L.
There are also 2 different mainboards namely MBAa6ULx & MBa6ULxL ('x' here is
not a placeholder, but part of the name). MBAa6ULx is for non-LGA variants
TQMa6ULx & TQMa6ULLx, while MBa6ULxL is used for TQMa6ULxL & TQMa6ULLxL.
It is also possible to mount a TQMa6ULxL to MBa6ULx using an LGA adapter
providing the sockets.
TQMa6UL1 uses MCIMX6G1 which has FEC2, CAN2, CSI and LCDIF disabled by fuses.
This wouldn't be a problem at all, iff fec would support EPROBE_DEFER for
Ethernet PHYs on a different MDIO bus. Both PHYs are connected to the same MDIO
bus. This is not a proble, but as FEC2 has the lower base address than FEC1
it is probed first. For this reason the PHYs have to be attached to FEC2 or
things wont work. But exactly this breaks on TQMa6UL1 which has no FEC2 at all.
There is a suggestion for fec driver at [3] but without solution (yet).
This is the single reason there is a 'tq,imx6ul-tqma6ul1' compatible.
In order for things to work, the PHYs have to be deleted from fec2 & mdio
subnode and added to fec1 again.
Regardings the file structure there is a .dtsi file for
* common common parts on all 4 module variants (LGA & non-LGA, imx6ul & imx6ull):
imx6ul-tqma6ul-common.dtsi
* common to non-LGA variants only: imx6ul-tqma6ulx-common.dtsi
* common to LGA variants only: imx6ul-tqma6ulxl-common.dtsi
This is valid for both TQMa6ULx and TQMa6ULLx. To not introduce another file
name separation, 'imx6ul-' is the prefix for common parts for imx6ul as well
as imx6ull.
Best regards,
Alexander
[1] https://www.tq-group.com/de/produkte/tq-embedded/arm-architektur/tqma6ulx/
[2] https://www.tq-group.com/de/produkte/tq-embedded/arm-architektur/tqma6ulxl/
[3] https://lkml.org/lkml/2021/10/14/430
Alexander Stein (4):
ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
Matthias Schiffer (1):
dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
.../devicetree/bindings/arm/fsl.yaml | 37 ++
arch/arm/boot/dts/Makefile | 5 +
arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi | 211 +++++++
arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts | 55 ++
arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi | 37 ++
arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi | 71 +++
.../arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi | 71 +++
arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi | 43 ++
.../arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi | 48 ++
.../boot/dts/imx6ull-tqma6ull2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi | 76 +++
.../boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi | 76 +++
arch/arm/boot/dts/mba6ulx.dtsi | 571 ++++++++++++++++++
16 files changed, 1361 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
create mode 100644 arch/arm/boot/dts/mba6ulx.dtsi
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread
* [PATCH v2 1/5] dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 16:04 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Matthias Schiffer, devicetree, linux-arm-kernel, Rob Herring,
Alexander Stein
From: Matthias Schiffer <matthias.schiffer@tq-group.com>
TQMa6ULx is a SOM family using NXP i.MX6UL CPU family.
TQMa6ULLx is a SOM family using NXP i.MX6ULL CPU family.
Both are available as a socket type as well as an LGA type.
For both variants there are the mainboards MBa6ULx and MBa6ULxL, trailing
'L' is LGA version.
Finally there is the possibility to use the socket module with an LGA
adapter on the MBa6ULxL.
The SOM needs a mainboard, therefore we provide compatibles using this
naming schema:
"tq,imx6ul-<SOM>" for the module and
"tq,imx6ul-<SOM>-<SBC>" for when mounted on the mainboard.
The i.MX6ULL version is done similar.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Acked-by: Rob Herring
.../devicetree/bindings/arm/fsl.yaml | 37 +++++++++++++++++++
1 file changed, 37 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 23e678232451..9343b64ce55e 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -613,6 +613,28 @@ properties:
- const: kontron,imx6ul-n6310-som
- const: fsl,imx6ul
+ - description: TQ-Systems TQMa6UL1 SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul1-mba6ulx
+ - const: tq,imx6ul-tqma6ul1 # MCIMX6G1
+ - const: fsl,imx6ul
+
+ - description: TQ-Systems TQMa6UL2 SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul2-mba6ulx
+ - const: tq,imx6ul-tqma6ul2 # MCIMX6G2
+ - const: fsl,imx6ul
+
+ - description: TQ-Systems TQMa6ULxL SoM on MBa6ULx[L] board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul2l-mba6ulx # using LGA adapter
+ - tq,imx6ul-tqma6ul2l-mba6ulxl
+ - const: tq,imx6ul-tqma6ul2l # MCIMX6G2, LGA SoM variant
+ - const: fsl,imx6ul
+
- description: i.MX6ULL based Boards
items:
- enum:
@@ -667,6 +689,21 @@ properties:
- const: kontron,imx6ull-n6411-som
- const: fsl,imx6ull
+ - description: TQ Systems TQMa6ULLx SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ull-tqma6ull2-mba6ulx
+ - const: tq,imx6ull-tqma6ull2 # MCIMX6Y2
+ - const: fsl,imx6ull
+
+ - description: TQ Systems TQMa6ULLxL SoM on MBa6ULx[L] board
+ items:
+ - enum:
+ - tq,imx6ull-tqma6ull2l-mba6ulx # using LGA adapter
+ - tq,imx6ull-tqma6ull2l-mba6ulxl
+ - const: tq,imx6ull-tqma6ull2l # MCIMX6Y2, LGA SoM variant
+ - const: fsl,imx6ull
+
- description: i.MX6ULZ based Boards
items:
- enum:
--
2.25.1
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 1/5] dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Matthias Schiffer, devicetree, linux-arm-kernel, Rob Herring,
Alexander Stein
From: Matthias Schiffer <matthias.schiffer@tq-group.com>
TQMa6ULx is a SOM family using NXP i.MX6UL CPU family.
TQMa6ULLx is a SOM family using NXP i.MX6ULL CPU family.
Both are available as a socket type as well as an LGA type.
For both variants there are the mainboards MBa6ULx and MBa6ULxL, trailing
'L' is LGA version.
Finally there is the possibility to use the socket module with an LGA
adapter on the MBa6ULxL.
The SOM needs a mainboard, therefore we provide compatibles using this
naming schema:
"tq,imx6ul-<SOM>" for the module and
"tq,imx6ul-<SOM>-<SBC>" for when mounted on the mainboard.
The i.MX6ULL version is done similar.
Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Acked-by: Rob Herring
.../devicetree/bindings/arm/fsl.yaml | 37 +++++++++++++++++++
1 file changed, 37 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 23e678232451..9343b64ce55e 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -613,6 +613,28 @@ properties:
- const: kontron,imx6ul-n6310-som
- const: fsl,imx6ul
+ - description: TQ-Systems TQMa6UL1 SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul1-mba6ulx
+ - const: tq,imx6ul-tqma6ul1 # MCIMX6G1
+ - const: fsl,imx6ul
+
+ - description: TQ-Systems TQMa6UL2 SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul2-mba6ulx
+ - const: tq,imx6ul-tqma6ul2 # MCIMX6G2
+ - const: fsl,imx6ul
+
+ - description: TQ-Systems TQMa6ULxL SoM on MBa6ULx[L] board
+ items:
+ - enum:
+ - tq,imx6ul-tqma6ul2l-mba6ulx # using LGA adapter
+ - tq,imx6ul-tqma6ul2l-mba6ulxl
+ - const: tq,imx6ul-tqma6ul2l # MCIMX6G2, LGA SoM variant
+ - const: fsl,imx6ul
+
- description: i.MX6ULL based Boards
items:
- enum:
@@ -667,6 +689,21 @@ properties:
- const: kontron,imx6ull-n6411-som
- const: fsl,imx6ull
+ - description: TQ Systems TQMa6ULLx SoM on MBa6ULx board
+ items:
+ - enum:
+ - tq,imx6ull-tqma6ull2-mba6ulx
+ - const: tq,imx6ull-tqma6ull2 # MCIMX6Y2
+ - const: fsl,imx6ull
+
+ - description: TQ Systems TQMa6ULLxL SoM on MBa6ULx[L] board
+ items:
+ - enum:
+ - tq,imx6ull-tqma6ull2l-mba6ulx # using LGA adapter
+ - tq,imx6ull-tqma6ull2l-mba6ulxl
+ - const: tq,imx6ull-tqma6ull2l # MCIMX6Y2, LGA SoM variant
+ - const: fsl,imx6ull
+
- description: i.MX6ULZ based Boards
items:
- enum:
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 2/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 16:04 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULx SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Removed 'status' property for non-disabled devices
* Removed superfluous blank lines
* Removed doubled status = "disabled"
* Moved 'chosen' node up
* Removed unit-address for GPIO buttons
* Removed internal (und unsupported) SPI device node
* Removed QSPI flash partitions
* Rename audio-codec node name
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi | 211 +++++++
arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts | 55 ++
arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi | 37 ++
arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi | 71 +++
arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi | 43 ++
arch/arm/boot/dts/mba6ulx.dtsi | 571 ++++++++++++++++++
8 files changed, 1005 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
create mode 100644 arch/arm/boot/dts/mba6ulx.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6a920b1a83bb..ce4673e270a2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -686,6 +686,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-kontron-n6310-s.dtb \
imx6ul-kontron-n6310-s-43.dtb \
imx6ul-liteboard.dtb \
+ imx6ul-tqma6ul1-mba6ulx.dtb \
+ imx6ul-tqma6ul2-mba6ulx.dtb \
imx6ul-opos6uldev.dtb \
imx6ul-pico-dwarf.dtb \
imx6ul-pico-hobbit.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
new file mode 100644
index 000000000000..eca94ed6451b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULxL
+ * - TQMa6ULLx
+ * - TQMa6ULLxL
+ */
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ pinctrl-1 = <&pinctrl_i2c4_recovery>;
+ scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pfuze3000: pmic@8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ reg_sw1a: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <6250>;
+ /* not used */
+ };
+
+ reg_sw1b_core: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ reg_sw2: sw2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_sw3_ddr: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_swbst: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ /* not used */
+ };
+
+ reg_snvs_3v0: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vrefddr: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vccsd: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_v33_3v3: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vldo1_3v3: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ /* not used */
+ };
+
+ reg_vldo2: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ /* not used */
+ };
+
+ reg_vldo3: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ /* not used */
+ };
+
+ reg_vldo4: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ jc42_1a: eeprom-temperature-sensor@1a {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1a>;
+ };
+
+ m24c64_50: eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+
+ m24c02_52: eeprom@52 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ read-only;
+ };
+
+ rtc0: rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+
+ /*
+ * PMIC & temperature sensor IRQ
+ * Both do currently not use IRQ
+ * potentially dangerous if used on baseboard
+ */
+ pmic-int-hog {
+ gpio-hog;
+ gpios = <24 0>;
+ input;
+ };
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <33000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ reg = <0>;
+ };
+};
+
+/* eMMC */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+ bus-width = <8>;
+ disable-wp;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001b8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c4_recovery: i2c4recoverygrp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x4001b8b0
+ MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21 0x4001b8b0
+ >;
+ };
+
+ pinctrl_pmic: pmic {
+ fsl,pins = <
+ /* PMIC irq */
+ MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x1b099
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
new file mode 100644
index 000000000000..f2a5f17f312e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul1.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL1 SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul1-mba6ulx", "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)
+ * and need to be disabled here again
+ */
+&can2 {
+ status = "disabled";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_mdc>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ max-speed = <100>;
+ reg = <0>;
+ };
+ };
+};
+
+&fec2 {
+ /delete-property/ phy-handle;
+ /delete-node/ mdio;
+};
+
+&iomuxc {
+ pinctrl_enet1_mdc: enet1mdcgrp {
+ fsl,pins = <
+ /* mdio */
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
new file mode 100644
index 000000000000..24192d012ef7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul-tqma6ul2.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL1 SoM";
+ compatible = "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * There are no module specific differences compared to TQMa6UL2,
+ * only external interfaces differ
+ */
+
+/*
+ * Devices not available on i.MX6ULG1 and should not be enabled on
+ * mainboard level (again)
+ */
+&can2 {
+ status = "disabled";
+};
+
+&csi {
+ status = "disabled";
+};
+
+&fec2 {
+ status = "disabled";
+};
+
+&lcdif {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
new file mode 100644
index 000000000000..0757df2b8f48
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULx SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul2-mba6ulx", "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
new file mode 100644
index 000000000000..e2e95dd92263
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL2 SoM";
+ compatible = "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
+
+&usdhc2 {
+ fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017051
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017051
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017051
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017051
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017051
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017051
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017051
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017051
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017051
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017051
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170e1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170e1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170e1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170e1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170e1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170e1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170e1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170e1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170e1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170e1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
new file mode 100644
index 000000000000..5afb9046c202
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULLx
+ */
+
+&m24c64_50 {
+ vcc-supply = <®_sw2>;
+};
+
+&m24c02_52 {
+ vcc-supply = <®_sw2>;
+};
+
+®_sw2 {
+ regulator-boot-on;
+ regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+ vmmc-supply = <®_sw2>;
+ vqmmc-supply = <®_vldo4>;
+};
+
+&iomuxc {
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70b9
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70b9
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70b9
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70b9
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/mba6ulx.dtsi b/arch/arm/boot/dts/mba6ulx.dtsi
new file mode 100644
index 000000000000..941f8725032c
--- /dev/null
+++ b/arch/arm/boot/dts/mba6ulx.dtsi
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+ model = "TQ-Systems MBA6ULx Baseboard";
+
+ aliases {
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ rtc0 = &rtc0;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <®_mba6ul_3v3>;
+ enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+
+ beeper: beeper {
+ compatible = "gpio-beeper";
+ gpios = <&expander_out1 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_buttons: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_buttons>;
+
+ button {
+ label = "s14";
+ linux,code = <KEY_1>;
+ gpios = <&expander_in0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "s6";
+ linux,code = <KEY_2>;
+ gpios = <&expander_in0 1 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "s7";
+ linux,code = <KEY_3>;
+ gpios = <&expander_in0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "POWER";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ led1 {
+ label = "led1";
+ gpios = <&expander_out1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&expander_out1 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_lcd_pwr: regulator-lcd-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-pwr";
+ gpio = <&expander_out0 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+
+ reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_mpcie: regulator-mpcie-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "mpcie-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander_out0 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ startup-delay-us = <500000>;
+ vin-supply = <®_mba6ul_3v3>;
+ };
+
+ reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+ compatible = "regulator-fixed";
+ gpio = <&expander_out1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "otg2-vbus-supply-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_mpcie>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0x6000000>;
+ linux,cma-default;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "imx-audio-tlv320aic32x4";
+ ssi-controller = <&sai1>;
+ audio-codec = <&tlv320aic32x4>;
+ audio-asrc = <&asrc>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_mba6ul_3v3>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_mba6ul_3v3>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <768000000>;
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ num-cs = <1>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_mba6ul_3v3>;
+ phy-reset-gpios = <&expander_out1 1 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_mdc>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_mba6ul_3v3>;
+ phy-reset-gpios = <&expander_out1 2 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ reg = <0>;
+ max-speed = <100>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+ reg = <1>;
+ max-speed = <100>;
+ };
+ };
+};
+
+&i2c4 {
+ tlv320aic32x4: audio-codec@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ clocks = <&clks IMX6UL_CLK_SAI1>;
+ clock-names = "mclk";
+ ldoin-supply = <®_mba6ul_3v3>;
+ iov-supply = <®_mba6ul_3v3>;
+ };
+
+ jc42: temperature-sensor@19 {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x19>;
+ };
+
+ expander_out0: gpio-expander@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ expander_in0: gpio-expander@21 {
+ compatible = "nxp,pca9554";
+ reg = <0x21>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander_in0>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ enet1_int-hog {
+ gpio-hog;
+ gpios = <6 0>;
+ input;
+ };
+
+ enet2_int-hog {
+ gpio-hog;
+ gpios = <7 0>;
+ input;
+ };
+ };
+
+ expander_out1: gpio-expander@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ analog_touch: touchscreen@41 {
+ compatible = "st,stmpe811";
+ reg = <0x41>;
+ interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpio4>;
+ interrupt-controller;
+ status = "disabled";
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */
+ st,ave-ctrl = <3>; /* 8 sample average control */
+ st,fraction-z = <7>; /* 7 length fractional part in z */
+ /*
+ * 50 mA typical 80 mA max touchscreen drivers
+ * current limit value
+ */
+ st,i-drive = <1>;
+ st,mod-12b = <1>; /* 12-bit ADC */
+ st,ref-sel = <0>; /* internal ADC reference */
+ st,sample-time = <4>; /* ADC converstion time: 80 clocks */
+ st,settling = <3>; /* 1 ms panel driver settling time */
+ st,touch-det-delay = <5>; /* 5 ms touch detect interrupt delay */
+ };
+ };
+
+ /* NXP SE97BTP with temperature sensor + eeprom */
+ se97b: eeprom@51 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&sai1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ assigned-clocks = <&clks IMX6UL_CLK_SAI1_SEL>,
+ <&clks IMX6UL_CLK_SAI1>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <0>, <24000000>;
+ fsl,sai-mclk-direction-output;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ /* for DTE mode, add below change */
+ /* fsl,dte-mode; */
+ /* pinctrl-0 = <&pinctrl_uart6dte>; */
+ uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-active-low;
+ rs485-rx-during-tx;
+ status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ power-active-high;
+ over-current-active-low;
+ /* we implement only dual role but not a fully featured OTG */
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+ disable-over-current;
+ vbus-supply = <®_otg2vbus_5v0>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ vmmc-supply = <®_mba6ul_3v3>;
+ vqmmc-supply = <®_vccsd>;
+ no-1-8-v;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog1>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_buttons: buttonsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x100b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x1b020
+ MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x1b020
+ MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x1b020
+ MX6UL_PAD_UART4_RX_DATA__ECSPI2_SS0 0x1b020
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b0a8
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0a0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0a0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b0a8
+ >;
+ };
+
+ pinctrl_enet2_mdc: enet2mdcgrp {
+ fsl,pins = <
+ /* mdio */
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_expander_in0: expanderin0grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x1b0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ /* 100 k PD, DSE 120 OHM, SPPEED LO */
+ MX6UL_PAD_GPIO1_IO09__PWM2_OUT 0x00003050
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK 0x1b0b1
+ MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC 0x1b0b1
+ MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA 0x1f0b8
+ MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA 0x110b0
+ MX6UL_PAD_CSI_DATA01__SAI1_MCLK 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x1b0b1
+ MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x1b0b1
+ MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS 0x1b0b1
+ MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart6dte: uart6dte {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__UART6_DTE_TX 0x1b0b1
+ MX6UL_PAD_CSI_MCLK__UART6_DTE_RX 0x1b0b1
+ MX6UL_PAD_CSI_HSYNC__UART6_DTE_RTS 0x1b0b1
+ MX6UL_PAD_CSI_VSYNC__UART6_DTE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x00017059
+ MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC 0x0001b0b0
+ MX6UL_PAD_GPIO1_IO04__USB_OTG1_PWR 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x00017059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x00017059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x00017059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x00017059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x00017059
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170b9
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170f9
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_wdog1: wdog1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0001b099
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 2/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULx SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* Removed 'status' property for non-disabled devices
* Removed superfluous blank lines
* Removed doubled status = "disabled"
* Moved 'chosen' node up
* Removed unit-address for GPIO buttons
* Removed internal (und unsupported) SPI device node
* Removed QSPI flash partitions
* Rename audio-codec node name
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi | 211 +++++++
arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts | 55 ++
arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi | 37 ++
arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts | 15 +
arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi | 71 +++
arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi | 43 ++
arch/arm/boot/dts/mba6ulx.dtsi | 571 ++++++++++++++++++
8 files changed, 1005 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
create mode 100644 arch/arm/boot/dts/mba6ulx.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 6a920b1a83bb..ce4673e270a2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -686,6 +686,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-kontron-n6310-s.dtb \
imx6ul-kontron-n6310-s-43.dtb \
imx6ul-liteboard.dtb \
+ imx6ul-tqma6ul1-mba6ulx.dtb \
+ imx6ul-tqma6ul2-mba6ulx.dtb \
imx6ul-opos6uldev.dtb \
imx6ul-pico-dwarf.dtb \
imx6ul-pico-hobbit.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
new file mode 100644
index 000000000000..eca94ed6451b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULxL
+ * - TQMa6ULLx
+ * - TQMa6ULLxL
+ */
+
+/ {
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ pinctrl-1 = <&pinctrl_i2c4_recovery>;
+ scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ status = "okay";
+
+ pfuze3000: pmic@8 {
+ compatible = "fsl,pfuze3000";
+ reg = <0x08>;
+
+ regulators {
+ reg_sw1a: sw1a {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-ramp-delay = <6250>;
+ /* not used */
+ };
+
+ reg_sw1b_core: sw1b {
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1475000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ reg_sw2: sw2 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_sw3_ddr: sw3 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1650000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_swbst: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ /* not used */
+ };
+
+ reg_snvs_3v0: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vrefddr: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_vccsd: vccsd {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_v33_3v3: v33 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_vldo1_3v3: vldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ /* not used */
+ };
+
+ reg_vldo2: vldo2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ /* not used */
+ };
+
+ reg_vldo3: vldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ /* not used */
+ };
+
+ reg_vldo4: vldo4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ jc42_1a: eeprom-temperature-sensor@1a {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x1a>;
+ };
+
+ m24c64_50: eeprom@50 {
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ pagesize = <32>;
+ };
+
+ m24c02_52: eeprom@52 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ read-only;
+ };
+
+ rtc0: rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+&gpio4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pmic>;
+
+ /*
+ * PMIC & temperature sensor IRQ
+ * Both do currently not use IRQ
+ * potentially dangerous if used on baseboard
+ */
+ pmic-int-hog {
+ gpio-hog;
+ gpios = <24 0>;
+ input;
+ };
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <33000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ reg = <0>;
+ };
+};
+
+/* eMMC */
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+ bus-width = <8>;
+ disable-wp;
+ non-removable;
+ no-sdio;
+ no-sd;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001b8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c4_recovery: i2c4recoverygrp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20 0x4001b8b0
+ MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21 0x4001b8b0
+ >;
+ };
+
+ pinctrl_pmic: pmic {
+ fsl,pins = <
+ /* PMIC irq */
+ MX6UL_PAD_CSI_DATA03__GPIO4_IO24 0x1b099
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
new file mode 100644
index 000000000000..f2a5f17f312e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul1.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL1 SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul1-mba6ulx", "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)
+ * and need to be disabled here again
+ */
+&can2 {
+ status = "disabled";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_mdc>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ max-speed = <100>;
+ reg = <0>;
+ };
+ };
+};
+
+&fec2 {
+ /delete-property/ phy-handle;
+ /delete-node/ mdio;
+};
+
+&iomuxc {
+ pinctrl_enet1_mdc: enet1mdcgrp {
+ fsl,pins = <
+ /* mdio */
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
new file mode 100644
index 000000000000..24192d012ef7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul-tqma6ul2.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL1 SoM";
+ compatible = "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * There are no module specific differences compared to TQMa6UL2,
+ * only external interfaces differ
+ */
+
+/*
+ * Devices not available on i.MX6ULG1 and should not be enabled on
+ * mainboard level (again)
+ */
+&can2 {
+ status = "disabled";
+};
+
+&csi {
+ status = "disabled";
+};
+
+&fec2 {
+ status = "disabled";
+};
+
+&lcdif {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
new file mode 100644
index 000000000000..0757df2b8f48
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULx SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul2-mba6ulx", "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
new file mode 100644
index 000000000000..e2e95dd92263
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL2 SoM";
+ compatible = "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
+
+&usdhc2 {
+ fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017051
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017051
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017051
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017051
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017051
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017051
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017051
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017051
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017051
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017051
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170e1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170e1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170e1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170e1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170e1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170e1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170e1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170e1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170e1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170e1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
new file mode 100644
index 000000000000..5afb9046c202
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULLx
+ */
+
+&m24c64_50 {
+ vcc-supply = <®_sw2>;
+};
+
+&m24c02_52 {
+ vcc-supply = <®_sw2>;
+};
+
+®_sw2 {
+ regulator-boot-on;
+ regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+ vmmc-supply = <®_sw2>;
+ vqmmc-supply = <®_vldo4>;
+};
+
+&iomuxc {
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70b9
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70b9
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70b9
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70b9
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/mba6ulx.dtsi b/arch/arm/boot/dts/mba6ulx.dtsi
new file mode 100644
index 000000000000..941f8725032c
--- /dev/null
+++ b/arch/arm/boot/dts/mba6ulx.dtsi
@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+ model = "TQ-Systems MBA6ULx Baseboard";
+
+ aliases {
+ mmc0 = &usdhc2;
+ mmc1 = &usdhc1;
+ rtc0 = &rtc0;
+ rtc1 = &snvs_rtc;
+ };
+
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ power-supply = <®_mba6ul_3v3>;
+ enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+ };
+
+ beeper: beeper {
+ compatible = "gpio-beeper";
+ gpios = <&expander_out1 6 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio_buttons: gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_buttons>;
+
+ button {
+ label = "s14";
+ linux,code = <KEY_1>;
+ gpios = <&expander_in0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "s6";
+ linux,code = <KEY_2>;
+ gpios = <&expander_in0 1 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "s7";
+ linux,code = <KEY_3>;
+ gpios = <&expander_in0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ button {
+ label = "POWER";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ gpio-key,wakeup;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ status = "okay";
+
+ led1 {
+ label = "led1";
+ gpios = <&expander_out1 4 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ led2 {
+ label = "led2";
+ gpios = <&expander_out1 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ reg_lcd_pwr: regulator-lcd-pwr {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-pwr";
+ gpio = <&expander_out0 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ status = "disabled";
+ };
+
+ reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "supply-mba6ul-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_mpcie: regulator-mpcie-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "mpcie-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&expander_out0 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ startup-delay-us = <500000>;
+ vin-supply = <®_mba6ul_3v3>;
+ };
+
+ reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+ compatible = "regulator-fixed";
+ gpio = <&expander_out1 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-name = "otg2-vbus-supply-5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_mpcie>;
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ reusable;
+ size = <0x6000000>;
+ linux,cma-default;
+ };
+ };
+
+ sound {
+ compatible = "fsl,imx-audio-tlv320aic32x4";
+ model = "imx-audio-tlv320aic32x4";
+ ssi-controller = <&sai1>;
+ audio-codec = <&tlv320aic32x4>;
+ audio-asrc = <&asrc>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ xceiver-supply = <®_mba6ul_3v3>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ xceiver-supply = <®_mba6ul_3v3>;
+ status = "okay";
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <768000000>;
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ num-cs = <1>;
+ status = "okay";
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ phy-supply = <®_mba6ul_3v3>;
+ phy-reset-gpios = <&expander_out1 1 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_mdc>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ phy-supply = <®_mba6ul_3v3>;
+ phy-reset-gpios = <&expander_out1 2 GPIO_ACTIVE_LOW>;
+ phy-reset-duration = <25>;
+ phy-reset-post-delay = <1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ reg = <0>;
+ max-speed = <100>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+ reg = <1>;
+ max-speed = <100>;
+ };
+ };
+};
+
+&i2c4 {
+ tlv320aic32x4: audio-codec@18 {
+ compatible = "ti,tlv320aic32x4";
+ reg = <0x18>;
+ clocks = <&clks IMX6UL_CLK_SAI1>;
+ clock-names = "mclk";
+ ldoin-supply = <®_mba6ul_3v3>;
+ iov-supply = <®_mba6ul_3v3>;
+ };
+
+ jc42: temperature-sensor@19 {
+ compatible = "nxp,se97", "jedec,jc-42.4-temp";
+ reg = <0x19>;
+ };
+
+ expander_out0: gpio-expander@20 {
+ compatible = "nxp,pca9554";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ expander_in0: gpio-expander@21 {
+ compatible = "nxp,pca9554";
+ reg = <0x21>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_expander_in0>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ enet1_int-hog {
+ gpio-hog;
+ gpios = <6 0>;
+ input;
+ };
+
+ enet2_int-hog {
+ gpio-hog;
+ gpios = <7 0>;
+ input;
+ };
+ };
+
+ expander_out1: gpio-expander@22 {
+ compatible = "nxp,pca9554";
+ reg = <0x22>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ analog_touch: touchscreen@41 {
+ compatible = "st,stmpe811";
+ reg = <0x41>;
+ interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpio4>;
+ interrupt-controller;
+ status = "disabled";
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ st,adc-freq = <1>; /* 3.25 MHz ADC clock speed */
+ st,ave-ctrl = <3>; /* 8 sample average control */
+ st,fraction-z = <7>; /* 7 length fractional part in z */
+ /*
+ * 50 mA typical 80 mA max touchscreen drivers
+ * current limit value
+ */
+ st,i-drive = <1>;
+ st,mod-12b = <1>; /* 12-bit ADC */
+ st,ref-sel = <0>; /* internal ADC reference */
+ st,sample-time = <4>; /* ADC converstion time: 80 clocks */
+ st,settling = <3>; /* 1 ms panel driver settling time */
+ st,touch-det-delay = <5>; /* 5 ms touch detect interrupt delay */
+ };
+ };
+
+ /* NXP SE97BTP with temperature sensor + eeprom */
+ se97b: eeprom@51 {
+ compatible = "nxp,se97b", "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&sai1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai1>;
+ assigned-clocks = <&clks IMX6UL_CLK_SAI1_SEL>,
+ <&clks IMX6UL_CLK_SAI1>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <0>, <24000000>;
+ fsl,sai-mclk-direction-output;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart6>;
+ /* for DTE mode, add below change */
+ /* fsl,dte-mode; */
+ /* pinctrl-0 = <&pinctrl_uart6dte>; */
+ uart-has-rtscts;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rts-active-low;
+ rs485-rx-during-tx;
+ status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_otg1>;
+ power-active-high;
+ over-current-active-low;
+ /* we implement only dual role but not a fully featured OTG */
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ dr_mode = "otg";
+ status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+ disable-over-current;
+ vbus-supply = <®_otg2vbus_5v0>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ vmmc-supply = <®_mba6ul_3v3>;
+ vqmmc-supply = <®_vccsd>;
+ no-1-8-v;
+ no-mmc;
+ no-sdio;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog1>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_buttons: buttonsgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0x100b0
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK 0x1b020
+ MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO 0x1b020
+ MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI 0x1b020
+ MX6UL_PAD_UART4_RX_DATA__ECSPI2_SS0 0x1b020
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b0a8
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0a0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0a0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b0a8
+ >;
+ };
+
+ pinctrl_enet2_mdc: enet2mdcgrp {
+ fsl,pins = <
+ /* mdio */
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_expander_in0: expanderin0grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x1b0b1
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ /* 100 k PD, DSE 120 OHM, SPPEED LO */
+ MX6UL_PAD_GPIO1_IO09__PWM2_OUT 0x00003050
+ >;
+ };
+
+ pinctrl_sai1: sai1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK 0x1b0b1
+ MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC 0x1b0b1
+ MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA 0x1f0b8
+ MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA 0x110b0
+ MX6UL_PAD_CSI_DATA01__SAI1_MCLK 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart6: uart6grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__UART6_DCE_TX 0x1b0b1
+ MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX 0x1b0b1
+ MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS 0x1b0b1
+ MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart6dte: uart6dte {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__UART6_DTE_TX 0x1b0b1
+ MX6UL_PAD_CSI_MCLK__UART6_DTE_RX 0x1b0b1
+ MX6UL_PAD_CSI_HSYNC__UART6_DTE_RTS 0x1b0b1
+ MX6UL_PAD_CSI_VSYNC__UART6_DTE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usb_otg1: usbotg1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID 0x00017059
+ MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC 0x0001b0b0
+ MX6UL_PAD_GPIO1_IO04__USB_OTG1_PWR 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x00017059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x00017059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x00017059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x00017059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x00017059
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170b9
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x00017069
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x000170f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x000170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x000170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x000170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x000170f9
+ /* WP */
+ MX6UL_PAD_UART1_CTS_B__GPIO1_IO18 0x0001b099
+ /* CD */
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x0001b099
+ >;
+ };
+
+ pinctrl_wdog1: wdog1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B 0x0001b099
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 3/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 16:04 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULxL SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi | 71 +++++++++++++++++++
.../arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi | 48 +++++++++++++
4 files changed, 135 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ce4673e270a2..4112b618a539 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -688,6 +688,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-liteboard.dtb \
imx6ul-tqma6ul1-mba6ulx.dtb \
imx6ul-tqma6ul2-mba6ulx.dtb \
+ imx6ul-tqma6ul2l-mba6ulx.dtb \
imx6ul-opos6uldev.dtb \
imx6ul-pico-dwarf.dtb \
imx6ul-pico-hobbit.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
new file mode 100644
index 000000000000..9d9b6b744a1c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6UL2L SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul2l-mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
new file mode 100644
index 000000000000..caf2c5d03f7e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL2L SoM";
+ compatible = "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017051
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017051
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017051
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017051
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017051
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017051
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017051
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017051
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017051
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017051
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170e1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
new file mode 100644
index 000000000000..ba84a4f70ebd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULxL
+ * - TQMa6ULLxL
+ */
+
+/ {
+ reg_vin: reg-vin {
+ compatible = "regulator-fixed";
+ regulator-name = "VIN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&m24c64_50 {
+ vcc-supply = <®_vin>;
+};
+
+&m24c02_52 {
+ vcc-supply = <®_vin>;
+};
+
+/* eMMC */
+&usdhc2 {
+ vmmc-supply = <®_vin>;
+ vqmmc-supply = <®_vldo4>;
+};
+
+&iomuxc {
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a9
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a9
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a9
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a9
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a9
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 3/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULxL SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi | 71 +++++++++++++++++++
.../arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi | 48 +++++++++++++
4 files changed, 135 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
create mode 100644 arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ce4673e270a2..4112b618a539 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -688,6 +688,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-liteboard.dtb \
imx6ul-tqma6ul1-mba6ulx.dtb \
imx6ul-tqma6ul2-mba6ulx.dtb \
+ imx6ul-tqma6ul2l-mba6ulx.dtb \
imx6ul-opos6uldev.dtb \
imx6ul-pico-dwarf.dtb \
imx6ul-pico-hobbit.dtb \
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
new file mode 100644
index 000000000000..9d9b6b744a1c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6UL2L SoM on MBa6ULx board";
+ compatible = "tq,imx6ul-tqma6ul2l-mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
new file mode 100644
index 000000000000..caf2c5d03f7e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6UL2L SoM";
+ compatible = "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017051
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017051
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017051
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017051
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017051
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017051
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017051
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017051
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017051
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017051
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170e1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
new file mode 100644
index 000000000000..ba84a4f70ebd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULxL
+ * - TQMa6ULLxL
+ */
+
+/ {
+ reg_vin: reg-vin {
+ compatible = "regulator-fixed";
+ regulator-name = "VIN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+};
+
+&m24c64_50 {
+ vcc-supply = <®_vin>;
+};
+
+&m24c02_52 {
+ vcc-supply = <®_vin>;
+};
+
+/* eMMC */
+&usdhc2 {
+ vmmc-supply = <®_vin>;
+ vqmmc-supply = <®_vldo4>;
+};
+
+&iomuxc {
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a9
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a9
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a9
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a9
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a9
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 4/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 16:04 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULLx SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-tqma6ull2-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi | 76 +++++++++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4112b618a539..3a6eccb6371a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -709,6 +709,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
+ imx6ull-tqma6ull2-mba6ulx.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
new file mode 100644
index 000000000000..e593b7036fc7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULL2 SoM on MBa6ULx board";
+ compatible = "tq,imx6ull-tqma6ull2-mba6ulx", "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
new file mode 100644
index 000000000000..326e6da91ed4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULL2 SoM";
+ compatible = "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+ /* Errata ERR010450 Workaround */
+ max-frequency = <99000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+ assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017031
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017039
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017039
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017039
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017039
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017039
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017039
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017039
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017039
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017039
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 4/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULLx SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-tqma6ull2-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi | 76 +++++++++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4112b618a539..3a6eccb6371a 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -709,6 +709,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-nand.dtb \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
+ imx6ull-tqma6ull2-mba6ulx.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
new file mode 100644
index 000000000000..e593b7036fc7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULL2 SoM on MBa6ULx board";
+ compatible = "tq,imx6ull-tqma6ull2-mba6ulx", "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
new file mode 100644
index 000000000000..326e6da91ed4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+ model = "TQ-Systems TQMa6ULL2 SoM";
+ compatible = "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+ /* Errata ERR010450 Workaround */
+ max-frequency = <99000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+ assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017031
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017039
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017039
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017039
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017039
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017039
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017039
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017039
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017039
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017039
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 5/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 16:04 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULLxL SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi | 76 +++++++++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3a6eccb6371a..9bf89273ae71 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -710,6 +710,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
imx6ull-tqma6ull2-mba6ulx.dtb \
+ imx6ull-tqma6ull2l-mba6ulx.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
new file mode 100644
index 000000000000..33437aae9822
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6ULL2L SoM on MBa6ULx board";
+ compatible = "tq,imx6ull-tqma6ull2l-mba6ulx", "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
new file mode 100644
index 000000000000..8e4d5cd18614
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6ULL2L SoM";
+ compatible = "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+ /* Errata ERR010450 Workaround */
+ max-frequency = <99000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+ assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017031
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017039
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017039
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017039
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017039
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017039
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017039
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017039
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017039
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017039
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
--
2.25.1
^ permalink raw reply related [flat|nested] 20+ messages in thread
* [PATCH v2 5/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
@ 2022-02-21 16:04 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-21 16:04 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Alexander Stein, devicetree, linux-arm-kernel
Add device trees for the MBa6ULx mainboard with TQMa6ULLxL SoMs.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
---
Changes in v2:
* None
arch/arm/boot/dts/Makefile | 1 +
.../boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts | 15 ++++
arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi | 76 +++++++++++++++++++
3 files changed, 92 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
create mode 100644 arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3a6eccb6371a..9bf89273ae71 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -710,6 +710,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ull-phytec-segin-ff-rdk-emmc.dtb \
imx6ull-phytec-segin-lc-rdk-nand.dtb \
imx6ull-tqma6ull2-mba6ulx.dtb \
+ imx6ull-tqma6ull2l-mba6ulx.dtb \
imx6ulz-14x14-evk.dtb \
imx6ulz-bsh-smm-m2.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
new file mode 100644
index 000000000000..33437aae9822
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6ULL2L SoM on MBa6ULx board";
+ compatible = "tq,imx6ull-tqma6ull2l-mba6ulx", "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
new file mode 100644
index 000000000000..8e4d5cd18614
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+ model = "TQ Systems TQMa6ULL2L SoM";
+ compatible = "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
+
+&usdhc2 {
+ fsl,tuning-step= <6>;
+ /* Errata ERR010450 Workaround */
+ max-frequency = <99000000>;
+ assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+ assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x00017031
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x00017039
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x00017039
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x00017039
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x00017039
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x00017039
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x00017039
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x00017039
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x00017039
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x00017039
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x000170f1
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x000170f1
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x000170f1
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x000170f1
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x000170f1
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x000170f1
+ MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x000170f1
+ MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x000170f1
+ MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x000170f1
+ MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x000170f1
+ /* rst */
+ MX6UL_PAD_NAND_ALE__GPIO4_IO10 0x0001b051
+ >;
+ };
+};
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 20+ messages in thread
* Re: [PATCH v2 1/5] dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-21 17:21 ` Krzysztof Kozlowski
-1 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2022-02-21 17:21 UTC (permalink / raw)
To: Alexander Stein, Rob Herring, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Matthias Schiffer, devicetree, linux-arm-kernel, Rob Herring
On 21/02/2022 17:04, Alexander Stein wrote:
> From: Matthias Schiffer <matthias.schiffer@tq-group.com>
>
> TQMa6ULx is a SOM family using NXP i.MX6UL CPU family.
> TQMa6ULLx is a SOM family using NXP i.MX6ULL CPU family.
> Both are available as a socket type as well as an LGA type.
> For both variants there are the mainboards MBa6ULx and MBa6ULxL, trailing
> 'L' is LGA version.
> Finally there is the possibility to use the socket module with an LGA
> adapter on the MBa6ULxL.
>
> The SOM needs a mainboard, therefore we provide compatibles using this
> naming schema:
>
> "tq,imx6ul-<SOM>" for the module and
> "tq,imx6ul-<SOM>-<SBC>" for when mounted on the mainboard.
> The i.MX6ULL version is done similar.
>
> Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Changes in v2:
> * Acked-by: Rob Herring
>
> .../devicetree/bindings/arm/fsl.yaml | 37 +++++++++++++++++++
> 1 file changed, 37 insertions(+)
>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v2 1/5] dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
@ 2022-02-21 17:21 ` Krzysztof Kozlowski
0 siblings, 0 replies; 20+ messages in thread
From: Krzysztof Kozlowski @ 2022-02-21 17:21 UTC (permalink / raw)
To: Alexander Stein, Rob Herring, Shawn Guo, Sascha Hauer, Fabio Estevam
Cc: Matthias Schiffer, devicetree, linux-arm-kernel, Rob Herring
On 21/02/2022 17:04, Alexander Stein wrote:
> From: Matthias Schiffer <matthias.schiffer@tq-group.com>
>
> TQMa6ULx is a SOM family using NXP i.MX6UL CPU family.
> TQMa6ULLx is a SOM family using NXP i.MX6ULL CPU family.
> Both are available as a socket type as well as an LGA type.
> For both variants there are the mainboards MBa6ULx and MBa6ULxL, trailing
> 'L' is LGA version.
> Finally there is the possibility to use the socket module with an LGA
> adapter on the MBa6ULxL.
>
> The SOM needs a mainboard, therefore we provide compatibles using this
> naming schema:
>
> "tq,imx6ul-<SOM>" for the module and
> "tq,imx6ul-<SOM>-<SBC>" for when mounted on the mainboard.
> The i.MX6ULL version is done similar.
>
> Signed-off-by: Matthias Schiffer <matthias.schiffer@tq-group.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
> ---
> Changes in v2:
> * Acked-by: Rob Herring
>
> .../devicetree/bindings/arm/fsl.yaml | 37 +++++++++++++++++++
> 1 file changed, 37 insertions(+)
>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
2022-02-21 16:04 ` Alexander Stein
@ 2022-02-22 2:28 ` Shawn Guo
-1 siblings, 0 replies; 20+ messages in thread
From: Shawn Guo @ 2022-02-22 2:28 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> Alexander Stein (4):
> ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
>
> Matthias Schiffer (1):
> dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
Applied all, thanks!
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
@ 2022-02-22 2:28 ` Shawn Guo
0 siblings, 0 replies; 20+ messages in thread
From: Shawn Guo @ 2022-02-22 2:28 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> Alexander Stein (4):
> ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
>
> Matthias Schiffer (1):
> dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
Applied all, thanks!
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
2022-02-22 2:28 ` Shawn Guo
@ 2022-02-22 2:34 ` Shawn Guo
-1 siblings, 0 replies; 20+ messages in thread
From: Shawn Guo @ 2022-02-22 2:34 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
On Tue, Feb 22, 2022 at 10:28:39AM +0800, Shawn Guo wrote:
> On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> > Alexander Stein (4):
> > ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> > ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> > ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> > ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
> >
> > Matthias Schiffer (1):
> > dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
>
> Applied all, thanks!
I replied too soon.
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dtb] Error 2
make[2]: *** Waiting for unfinished jobs....
DTC arch/arm/boot/dts/imx6ul-pico-dwarf.dtb
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dtb] Error 2
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dtb] Error 2
make[1]: *** [/home/r65073/repos/korg/imx/Makefile:1370: dtbs] Error 2
make[1]: Leaving directory '/home/r65073/repos/korg/imx/IMX6'
make: *** [Makefile:219: __sub-make] Error 2
Shawn
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
@ 2022-02-22 2:34 ` Shawn Guo
0 siblings, 0 replies; 20+ messages in thread
From: Shawn Guo @ 2022-02-22 2:34 UTC (permalink / raw)
To: Alexander Stein
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
On Tue, Feb 22, 2022 at 10:28:39AM +0800, Shawn Guo wrote:
> On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> > Alexander Stein (4):
> > ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> > ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> > ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> > ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
> >
> > Matthias Schiffer (1):
> > dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
>
> Applied all, thanks!
I replied too soon.
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dtb] Error 2
make[2]: *** Waiting for unfinished jobs....
DTC arch/arm/boot/dts/imx6ul-pico-dwarf.dtb
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dtb] Error 2
../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names): /gpio-keys/button: Duplicate node name
ERROR: Input tree has errors, aborting (use -f to force output)
make[2]: *** [../scripts/Makefile.lib:351: arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dtb] Error 2
make[1]: *** [/home/r65073/repos/korg/imx/Makefile:1370: dtbs] Error 2
make[1]: Leaving directory '/home/r65073/repos/korg/imx/IMX6'
make: *** [Makefile:219: __sub-make] Error 2
Shawn
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: (EXT) Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
2022-02-22 2:34 ` Shawn Guo
@ 2022-02-22 7:01 ` Alexander Stein
-1 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-22 7:01 UTC (permalink / raw)
To: Shawn Guo
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
Hi Shawn,
Am Dienstag, 22. Februar 2022, 03:34:23 CET schrieb Shawn Guo:
> On Tue, Feb 22, 2022 at 10:28:39AM +0800, Shawn Guo wrote:
> > On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> > > Alexander Stein (4):
> > > ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> > > ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> > > ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> > > ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
> > >
> > > Matthias Schiffer (1):
> > > dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
> >
> > Applied all, thanks!
>
> I replied too soon.
>
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dtb] Error 2 make[2]: *** Waiting
> for unfinished jobs....
> DTC arch/arm/boot/dts/imx6ul-pico-dwarf.dtb
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dtb] Error 2
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dtb] Error 2 make[1]: ***
> [/home/r65073/repos/korg/imx/Makefile:1370: dtbs] Error 2 make[1]: Leaving
> directory '/home/r65073/repos/korg/imx/IMX6'
> make: *** [Makefile:219: __sub-make] Error 2
Ah, thanks for pointing this out. Sorry, this is the result from trying to
trigger a dtbs_check warning.
Will send a fixed version.
Sorry for the noise.
Regards,
Alexander
^ permalink raw reply [flat|nested] 20+ messages in thread
* Re: (EXT) Re: [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules
@ 2022-02-22 7:01 ` Alexander Stein
0 siblings, 0 replies; 20+ messages in thread
From: Alexander Stein @ 2022-02-22 7:01 UTC (permalink / raw)
To: Shawn Guo
Cc: Rob Herring, Krzysztof Kozlowski, Sascha Hauer, Fabio Estevam,
devicetree, linux-arm-kernel
Hi Shawn,
Am Dienstag, 22. Februar 2022, 03:34:23 CET schrieb Shawn Guo:
> On Tue, Feb 22, 2022 at 10:28:39AM +0800, Shawn Guo wrote:
> > On Mon, Feb 21, 2022 at 05:04:14PM +0100, Alexander Stein wrote:
> > > Alexander Stein (4):
> > > ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees
> > > ARM: dts: imx6ul: add TQ-Systems MBa6ULxL device trees
> > > ARM: dts: imx6ull: add TQ-Systems MBa6ULLx device trees
> > > ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL device trees
> > >
> > > Matthias Schiffer (1):
> > > dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L)
> >
> > Applied all, thanks!
>
> I replied too soon.
>
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dtb] Error 2 make[2]: *** Waiting
> for unfinished jobs....
> DTC arch/arm/boot/dts/imx6ul-pico-dwarf.dtb
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dtb] Error 2
> ../arch/arm/boot/dts/mba6ulx.dtsi:46.10-50.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:52.10-56.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name
> ../arch/arm/boot/dts/mba6ulx.dtsi:58.10-63.5: ERROR (duplicate_node_names):
> /gpio-keys/button: Duplicate node name ERROR: Input tree has errors,
> aborting (use -f to force output)
> make[2]: *** [../scripts/Makefile.lib:351:
> arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dtb] Error 2 make[1]: ***
> [/home/r65073/repos/korg/imx/Makefile:1370: dtbs] Error 2 make[1]: Leaving
> directory '/home/r65073/repos/korg/imx/IMX6'
> make: *** [Makefile:219: __sub-make] Error 2
Ah, thanks for pointing this out. Sorry, this is the result from trying to
trigger a dtbs_check warning.
Will send a fixed version.
Sorry for the noise.
Regards,
Alexander
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 20+ messages in thread
end of thread, other threads:[~2022-02-22 7:03 UTC | newest]
Thread overview: 20+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-02-21 16:04 [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-21 16:04 ` [PATCH v2 1/5] dt-bindings: arm: fsl: add TQ Systems boards based on i.MX6UL(L) Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-21 17:21 ` Krzysztof Kozlowski
2022-02-21 17:21 ` Krzysztof Kozlowski
2022-02-21 16:04 ` [PATCH v2 2/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULx device trees Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-21 16:04 ` [PATCH v2 3/5] ARM: dts: imx6ul: add TQ-Systems MBa6ULxL " Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-21 16:04 ` [PATCH v2 4/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLx " Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-21 16:04 ` [PATCH v2 5/5] ARM: dts: imx6ull: add TQ-Systems MBa6ULLxL " Alexander Stein
2022-02-21 16:04 ` Alexander Stein
2022-02-22 2:28 ` [PATCH v2 0/5] Support for TQMa6ULx & TQMa6ULxL modules Shawn Guo
2022-02-22 2:28 ` Shawn Guo
2022-02-22 2:34 ` Shawn Guo
2022-02-22 2:34 ` Shawn Guo
2022-02-22 7:01 ` (EXT) " Alexander Stein
2022-02-22 7:01 ` Alexander Stein
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.