[PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Add support for backlight. This panel supports backlight control
through the QCOM WLED driver in Xiaomi Poco F1 device.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
 drivers/gpu/drm/panel/panel-novatek-nt36672a.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
index 231f371901e8..6d6ce42787e2 100644
--- a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
+++ b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
@@ -628,6 +628,10 @@ static int nt36672a_panel_add(struct nt36672a_panel *pinfo)
 
 	drm_panel_init(&pinfo->base, dev, &panel_funcs, DRM_MODE_CONNECTOR_DSI);
 
+	ret = drm_panel_of_backlight(&pinfo->base);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get backlight\n");
+
 	drm_panel_add(&pinfo->base);
 
 	return 0;
-- 
2.35.1

[PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Add support for backlight. This panel supports backlight control
through the QCOM WLED driver in Xiaomi Poco F1 device.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
 drivers/gpu/drm/panel/panel-novatek-nt36672a.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
index 231f371901e8..6d6ce42787e2 100644
--- a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
+++ b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
@@ -628,6 +628,10 @@ static int nt36672a_panel_add(struct nt36672a_panel *pinfo)
 
 	drm_panel_init(&pinfo->base, dev, &panel_funcs, DRM_MODE_CONNECTOR_DSI);
 
+	ret = drm_panel_of_backlight(&pinfo->base);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to get backlight\n");
+
 	drm_panel_add(&pinfo->base);
 
 	return 0;
-- 
2.35.1

[PATCH v2 2/3] dt-bindings: display: novatek,nt36672a: add backlight property

[Joel Selvaraj]

Add backlight property and update example to include it.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
 .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
index 563766d283f6..41ee3157a1cd 100644
--- a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
+++ b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
@@ -46,6 +46,7 @@ properties:
 
   reg: true
   port: true
+  backlight: true
 
 required:
   - compatible
@@ -73,6 +74,7 @@ examples:
             vddpos-supply = <&lab>;
             vddneg-supply = <&ibb>;
 
+            backlight = <&pmi8998_wled>;
             reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
 
             port {
-- 
2.35.1

[PATCH v2 2/3] dt-bindings: display: novatek, nt36672a: add backlight property

[Joel Selvaraj]

Add backlight property and update example to include it.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
 .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
index 563766d283f6..41ee3157a1cd 100644
--- a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
+++ b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
@@ -46,6 +46,7 @@ properties:
 
   reg: true
   port: true
+  backlight: true
 
 required:
   - compatible
@@ -73,6 +74,7 @@ examples:
             vddpos-supply = <&lab>;
             vddneg-supply = <&ibb>;
 
+            backlight = <&pmi8998_wled>;
             reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
 
             port {
-- 
2.35.1

[PATCH v2 3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel

[Joel Selvaraj]

Xiaomi Poco F1 uses the QCOM WLED driver for backlight control.
Enable and link it to the panel to use it.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
Changes in v2:
 - Remove qcom,enabled-strings property as either it or qcom,num-strings
   should be present. qcom,num-strings is specified and sufficient.
   (Marijn Suijten's Suggestion)

 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 798fc72578a7..d88dc07205f7 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -231,6 +231,7 @@ panel@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		backlight = <&pmi8998_wled>;
 		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
 
 		port {
@@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active {
 	};
 };
 
+&pmi8998_wled {
+	status = "okay";
+	qcom,current-boost-limit = <970>;
+	qcom,ovp-millivolt = <29600>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+	qcom,switching-freq = <600>;
+	qcom,external-pfet;
+	qcom,cabc;
+};
+
 &pm8998_pon {
 	resin {
 		compatible = "qcom,pm8941-resin";
-- 
2.35.1

[PATCH v2 3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel

[Joel Selvaraj]

Xiaomi Poco F1 uses the QCOM WLED driver for backlight control.
Enable and link it to the panel to use it.

Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
---
Changes in v2:
 - Remove qcom,enabled-strings property as either it or qcom,num-strings
   should be present. qcom,num-strings is specified and sufficient.
   (Marijn Suijten's Suggestion)

 arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 798fc72578a7..d88dc07205f7 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -231,6 +231,7 @@ panel@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		backlight = <&pmi8998_wled>;
 		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
 
 		port {
@@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active {
 	};
 };
 
+&pmi8998_wled {
+	status = "okay";
+	qcom,current-boost-limit = <970>;
+	qcom,ovp-millivolt = <29600>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+	qcom,switching-freq = <600>;
+	qcom,external-pfet;
+	qcom,cabc;
+};
+
 &pm8998_pon {
 	resin {
 		compatible = "qcom,pm8941-resin";
-- 
2.35.1

Re: [PATCH v2 2/3] dt-bindings: display: novatek,nt36672a: add backlight property

[Rob Herring]

On Fri, 01 Apr 2022 05:48:09 +0530, Joel Selvaraj wrote:
> Add backlight property and update example to include it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
> ---
>  .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v2 2/3] dt-bindings: display: novatek,nt36672a: add backlight property

[Rob Herring]

On Fri, 01 Apr 2022 05:48:09 +0530, Joel Selvaraj wrote:
> Add backlight property and update example to include it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>
> ---
>  .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring <robh@kernel.org>

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Marijn Suijten]

On 2022-04-01 05:48:08, Joel Selvaraj wrote:
> Add support for backlight. This panel supports backlight control
> through the QCOM WLED driver in Xiaomi Poco F1 device.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
>  drivers/gpu/drm/panel/panel-novatek-nt36672a.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> index 231f371901e8..6d6ce42787e2 100644
> --- a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> +++ b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> @@ -628,6 +628,10 @@ static int nt36672a_panel_add(struct nt36672a_panel *pinfo)
>  
>  	drm_panel_init(&pinfo->base, dev, &panel_funcs, DRM_MODE_CONNECTOR_DSI);
>  
> +	ret = drm_panel_of_backlight(&pinfo->base);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to get backlight\n");
> +
>  	drm_panel_add(&pinfo->base);
>  
>  	return 0;
> -- 
> 2.35.1
> 

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Marijn Suijten]

On 2022-04-01 05:48:08, Joel Selvaraj wrote:
> Add support for backlight. This panel supports backlight control
> through the QCOM WLED driver in Xiaomi Poco F1 device.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
>  drivers/gpu/drm/panel/panel-novatek-nt36672a.c | 4 ++++
>  1 file changed, 4 insertions(+)
> 
> diff --git a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> index 231f371901e8..6d6ce42787e2 100644
> --- a/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> +++ b/drivers/gpu/drm/panel/panel-novatek-nt36672a.c
> @@ -628,6 +628,10 @@ static int nt36672a_panel_add(struct nt36672a_panel *pinfo)
>  
>  	drm_panel_init(&pinfo->base, dev, &panel_funcs, DRM_MODE_CONNECTOR_DSI);
>  
> +	ret = drm_panel_of_backlight(&pinfo->base);
> +	if (ret)
> +		return dev_err_probe(dev, ret, "Failed to get backlight\n");
> +
>  	drm_panel_add(&pinfo->base);
>  
>  	return 0;
> -- 
> 2.35.1
> 

Re: [PATCH v2 3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel

[Marijn Suijten]

On 2022-04-01 05:48:10, Joel Selvaraj wrote:
> Xiaomi Poco F1 uses the QCOM WLED driver for backlight control.
> Enable and link it to the panel to use it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
> Changes in v2:
>  - Remove qcom,enabled-strings property as either it or qcom,num-strings
>    should be present. qcom,num-strings is specified and sufficient.
>    (Marijn Suijten's Suggestion)

Thanks :)

>  arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> index 798fc72578a7..d88dc07205f7 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> @@ -231,6 +231,7 @@ panel@0 {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
>  
> +		backlight = <&pmi8998_wled>;
>  		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
>  
>  		port {
> @@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active {
>  	};
>  };
>  
> +&pmi8998_wled {
> +	status = "okay";
> +	qcom,current-boost-limit = <970>;
> +	qcom,ovp-millivolt = <29600>;
> +	qcom,current-limit-microamp = <20000>;
> +	qcom,num-strings = <2>;
> +	qcom,switching-freq = <600>;
> +	qcom,external-pfet;
> +	qcom,cabc;

Unlike the number of connected strings and configured ovp/current
limits, aren't external-pfet (and probably switching-freq, perhaps CABC)
hardware features that are common across all users of `pmi8998`?

- Marijn

> +};
> +
>  &pm8998_pon {
>  	resin {
>  		compatible = "qcom,pm8941-resin";
> -- 
> 2.35.1
> 

Re: [PATCH v2 3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel

[Marijn Suijten]

On 2022-04-01 05:48:10, Joel Selvaraj wrote:
> Xiaomi Poco F1 uses the QCOM WLED driver for backlight control.
> Enable and link it to the panel to use it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
> Changes in v2:
>  - Remove qcom,enabled-strings property as either it or qcom,num-strings
>    should be present. qcom,num-strings is specified and sufficient.
>    (Marijn Suijten's Suggestion)

Thanks :)

>  arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts | 12 ++++++++++++
>  1 file changed, 12 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> index 798fc72578a7..d88dc07205f7 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
> @@ -231,6 +231,7 @@ panel@0 {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
>  
> +		backlight = <&pmi8998_wled>;
>  		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
>  
>  		port {
> @@ -314,6 +315,17 @@ vol_up_pin_a: vol-up-active {
>  	};
>  };
>  
> +&pmi8998_wled {
> +	status = "okay";
> +	qcom,current-boost-limit = <970>;
> +	qcom,ovp-millivolt = <29600>;
> +	qcom,current-limit-microamp = <20000>;
> +	qcom,num-strings = <2>;
> +	qcom,switching-freq = <600>;
> +	qcom,external-pfet;
> +	qcom,cabc;

Unlike the number of connected strings and configured ovp/current
limits, aren't external-pfet (and probably switching-freq, perhaps CABC)
hardware features that are common across all users of `pmi8998`?

- Marijn

> +};
> +
>  &pm8998_pon {
>  	resin {
>  		compatible = "qcom,pm8941-resin";
> -- 
> 2.35.1
> 

Re: [PATCH v2 2/3] dt-bindings: display: novatek,nt36672a: add backlight property

[Marijn Suijten]

On 2022-04-01 05:48:09, Joel Selvaraj wrote:
> Add backlight property and update example to include it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
>  .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> index 563766d283f6..41ee3157a1cd 100644
> --- a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> @@ -46,6 +46,7 @@ properties:
>  
>    reg: true
>    port: true
> +  backlight: true
>  
>  required:
>    - compatible
> @@ -73,6 +74,7 @@ examples:
>              vddpos-supply = <&lab>;
>              vddneg-supply = <&ibb>;
>  
> +            backlight = <&pmi8998_wled>;
>              reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
>  
>              port {
> -- 
> 2.35.1
> 

Re: [PATCH v2 2/3] dt-bindings: display: novatek,nt36672a: add backlight property

[Marijn Suijten]

On 2022-04-01 05:48:09, Joel Selvaraj wrote:
> Add backlight property and update example to include it.
> 
> Signed-off-by: Joel Selvaraj <jo@jsfamily.in>

Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>

> ---
>  .../devicetree/bindings/display/panel/novatek,nt36672a.yaml     | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> index 563766d283f6..41ee3157a1cd 100644
> --- a/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> +++ b/Documentation/devicetree/bindings/display/panel/novatek,nt36672a.yaml
> @@ -46,6 +46,7 @@ properties:
>  
>    reg: true
>    port: true
> +  backlight: true
>  
>  required:
>    - compatible
> @@ -73,6 +74,7 @@ examples:
>              vddpos-supply = <&lab>;
>              vddneg-supply = <&ibb>;
>  
> +            backlight = <&pmi8998_wled>;
>              reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
>  
>              port {
> -- 
> 2.35.1
> 

Re: (subset) [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Bjorn Andersson]

On Fri, 1 Apr 2022 05:48:08 +0530, Joel Selvaraj wrote:
> Add support for backlight. This panel supports backlight control
> through the QCOM WLED driver in Xiaomi Poco F1 device.
> 
> 

Applied, thanks!

[3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel
      commit: 89561886191c0dcb6ce1491f14552eac16e14a80

Best regards,
-- 
Bjorn Andersson <bjorn.andersson@linaro.org>

Re: (subset) [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Bjorn Andersson]

On Fri, 1 Apr 2022 05:48:08 +0530, Joel Selvaraj wrote:
> Add support for backlight. This panel supports backlight control
> through the QCOM WLED driver in Xiaomi Poco F1 device.
> 
> 

Applied, thanks!

[3/3] arm64: dts: qcom: sdm845-xiaomi-beryllium: enable qcom wled backlight and link to panel
      commit: 89561886191c0dcb6ce1491f14552eac16e14a80

Best regards,
-- 
Bjorn Andersson <bjorn.andersson@linaro.org>

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi,

I can see that the dts changes from this patch series has been applied 
to 5.19-rc1 release. However, this patch that has the related change to 
the panel driver, is not applied in the 5.19-rc1 release. Any particular 
reason why it's not picked up? or just that, it got missed out? Kindly 
let me know if changes are required from my end.

With Regards,
Joel Selvaraj

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi,

I can see that the dts changes from this patch series has been applied 
to 5.19-rc1 release. However, this patch that has the related change to 
the panel driver, is not applied in the 5.19-rc1 release. Any particular 
reason why it's not picked up? or just that, it got missed out? Kindly 
let me know if changes are required from my end.

With Regards,
Joel Selvaraj

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Sumit Semwal]

Hi Joel,

On Wed, 8 Jun 2022 at 00:01, Joel Selvaraj <jo@jsfamily.in> wrote:
>
> Hi,
>
> I can see that the dts changes from this patch series has been applied
> to 5.19-rc1 release. However, this patch that has the related change to
> the panel driver, is not applied in the 5.19-rc1 release. Any particular
> reason why it's not picked up? or just that, it got missed out? Kindly
> let me know if changes are required from my end.

This is entirely my fault - It somehow missed my radar, and I didn't
queue it up. I will push it via drm-misc tree tonight. Apologies
again!
>
> With Regards,
> Joel Selvaraj

Best,
Sumit.

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Sumit Semwal]

Hi Joel,

On Wed, 8 Jun 2022 at 00:01, Joel Selvaraj <jo@jsfamily.in> wrote:
>
> Hi,
>
> I can see that the dts changes from this patch series has been applied
> to 5.19-rc1 release. However, this patch that has the related change to
> the panel driver, is not applied in the 5.19-rc1 release. Any particular
> reason why it's not picked up? or just that, it got missed out? Kindly
> let me know if changes are required from my end.

This is entirely my fault - It somehow missed my radar, and I didn't
queue it up. I will push it via drm-misc tree tonight. Apologies
again!
>
> With Regards,
> Joel Selvaraj

Best,
Sumit.

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi Sumit,

On 08/06/22 22:00, Sumit Semwal wrote:
> This is entirely my fault - It somehow missed my radar, and I didn't
> queue it up. I will push it via drm-misc tree tonight. Apologies
> again!

No problem. Thanks for the update! So it will land on upcoming 5.19-rcs 
or 5.20-rc?

> Best,
> Sumit.

Best Regards,
Joel Selvaraj

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi Sumit,

On 08/06/22 22:00, Sumit Semwal wrote:
> This is entirely my fault - It somehow missed my radar, and I didn't
> queue it up. I will push it via drm-misc tree tonight. Apologies
> again!

No problem. Thanks for the update! So it will land on upcoming 5.19-rcs 
or 5.20-rc?

> Best,
> Sumit.

Best Regards,
Joel Selvaraj

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Sumit Semwal]

Hi Joel,

On Wed, 8 Jun 2022 at 22:10, Joel Selvaraj <jo@jsfamily.in> wrote:
>
> Hi Sumit,
>
> On 08/06/22 22:00, Sumit Semwal wrote:
> > This is entirely my fault - It somehow missed my radar, and I didn't
> > queue it up. I will push it via drm-misc tree tonight. Apologies
> > again!
>
> No problem. Thanks for the update! So it will land on upcoming 5.19-rcs
> or 5.20-rc?
Not for 5.19-rcs for sure, but I think it should make it for 5.20-rcs?
>
> > Best,
> > Sumit.
>
> Best Regards,
> Joel Selvaraj

Best,
Sumit.

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Sumit Semwal]

Hi Joel,

On Wed, 8 Jun 2022 at 22:10, Joel Selvaraj <jo@jsfamily.in> wrote:
>
> Hi Sumit,
>
> On 08/06/22 22:00, Sumit Semwal wrote:
> > This is entirely my fault - It somehow missed my radar, and I didn't
> > queue it up. I will push it via drm-misc tree tonight. Apologies
> > again!
>
> No problem. Thanks for the update! So it will land on upcoming 5.19-rcs
> or 5.20-rc?
Not for 5.19-rcs for sure, but I think it should make it for 5.20-rcs?
>
> > Best,
> > Sumit.
>
> Best Regards,
> Joel Selvaraj

Best,
Sumit.

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi Sumit,

On 08/06/22 23:22, Sumit Semwal wrote:
> Not for 5.19-rcs for sure, but I think it should make it for 5.20-rcs?

Ok. No problem. Thanks.

> Best,
> Sumit.

Best Regards,
Joel Selvaraj

Re: [PATCH v2 1/3] drm/panel: nt36672a: add backlight support

[Joel Selvaraj]

Hi Sumit,

On 08/06/22 23:22, Sumit Semwal wrote:
> Not for 5.19-rcs for sure, but I think it should make it for 5.20-rcs?

Ok. No problem. Thanks.

> Best,
> Sumit.

Best Regards,
Joel Selvaraj