All of lore.kernel.org
 help / color / mirror / Atom feed
From: "Joseph S. Barrera III" <joebar@chromium.org>
To: LKML <linux-kernel@vger.kernel.org>
Cc: Douglas Anderson <dianders@chromium.org>,
	Alexandru M Stan <amstan@chromium.org>,
	"Joseph S. Barrera III" <joebar@chromium.org>,
	Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	devicetree@vger.kernel.org, linux-arm-msm@vger.kernel.org
Subject: [PATCH v5 3/5] arm64: dts: qcom: sc7180: Add quackingstick dts files
Date: Tue, 10 May 2022 15:44:25 -0700	[thread overview]
Message-ID: <20220510154406.v5.3.I0977b1a08830d0caa8bfb1bdedb4ecceac709a7f@changeid> (raw)
In-Reply-To: <20220510154406.v5.1.Id769ddc5dbf570ccb511db96da59f97d08f75a9c@changeid>

Quackingstick is a trogdor-based board. These dts files are copies from
the downstream Chrome OS 5.4 kernel, but with downstream bits removed.

Signed-off-by: Joseph S. Barrera III <joebar@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

---

Changes in v5:
- Removed extra newline
- Added comment that compatible will be filled in per-board

Changes in v4:
- Added missing version history

Changes in v3:
- First inclusion in this series

 arch/arm64/boot/dts/qcom/Makefile             |   2 +
 .../sc7180-trogdor-quackingstick-r0-lte.dts   |  38 ++
 .../qcom/sc7180-trogdor-quackingstick-r0.dts  |  26 ++
 .../qcom/sc7180-trogdor-quackingstick.dtsi    | 324 ++++++++++++++++++
 4 files changed, 390 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 2330b5ea13bf..5cfd6316768c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -85,6 +85,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r2-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-quackingstick-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-quackingstick-r0-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev0-boe.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev0-inx.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-boe.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts
new file mode 100644
index 000000000000..35e8945fc56d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x600 => 1536
+ *  - bits 11..8: Panel ID: 0x6 (AUO)
+ */
+
+#include "sc7180-trogdor-quackingstick-r0.dts"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Quackingstick (rev0+) with LTE";
+	compatible = "google,quackingstick-sku1536", "qcom,sc7180";
+};
+
+&ap_sar_sensor {
+	compatible = "semtech,sx9324";
+	semtech,ph0-pin = <3 1 3>;
+	semtech,ph1-pin = <2 1 2>;
+	semtech,ph2-pin = <3 3 1>;
+	semtech,ph3-pin = <1 3 3>;
+	semtech,ph01-resolution = <1024>;
+	semtech,ph23-resolution = <1024>;
+	semtech,startup-sensor = <1>;
+	semtech,ph01-proxraw-strength = <3>;
+	semtech,ph23-proxraw-strength = <3>;
+	semtech,avg-pos-strength = <256>;
+
+	/delete-property/ svdd-supply;
+	vdd-supply = <&pp1800_prox>;
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts
new file mode 100644
index 000000000000..5c81e44ed4a5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x601 => 1537
+ *  - bits 11..8: Panel ID: 0x6 (AUO)
+ */
+
+#include "sc7180-trogdor-quackingstick.dtsi"
+
+/ {
+	model = "Google Quackingstick (rev0+)";
+	compatible = "google,quackingstick-sku1537", "qcom,sc7180";
+};
+
+&dsi_phy {
+	qcom,phy-rescode-offset-top = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
+	qcom,phy-rescode-offset-bot = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
+	qcom,phy-drive-ldo-level = <375>;
+};
+
+&panel {
+	compatible = "auo,b101uan08.3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
new file mode 100644
index 000000000000..d39f43757932
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
@@ -0,0 +1,324 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180.dtsi"
+
+ap_ec_spi: &spi6 {};
+ap_h1_spi: &spi0 {};
+
+#include "sc7180-trogdor.dtsi"
+
+/ {
+	ppvar_lcd: ppvar-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_lcd";
+
+		gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ppvar_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	v1p8_disp: v1p8-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p8_disp";
+
+		gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pp1800_disp_on>;
+
+		vin-supply = <&pp3300_a>;
+	};
+};
+
+&ap_tp_i2c {
+	status = "disabled";
+};
+
+&backlight {
+	pwms = <&cros_ec_pwm 0>;
+};
+
+&camcc {
+	status = "okay";
+};
+
+&dsi0 {
+	panel: panel@0 {
+		/* Compatible will be filled in per-board */
+		reg = <0>;
+		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_rst>;
+		avdd-supply = <&ppvar_lcd>;
+		pp1800-supply = <&v1p8_disp>;
+		pp3300-supply = <&pp3300_dx_edp>;
+		backlight = <&backlight>;
+		rotation = <270>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&sdhc_2 {
+	status = "okay";
+};
+
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+pp3300_disp_on: &pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+
+tp_en: &en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "AMP_EN",
+			  "P_SENSOR_INT_L",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "",
+			  "",
+			  "AMP_DIN",
+			  "PEN_DET_ODL",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RST",
+			  "UIM2_PRESENT_L",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "PP1800_DISP_ON",
+			  "LCD_RST",
+			  "PPVAR_LCD_EN",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_TS_I2C_SDA",
+			  "AP_TS_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	lcd_rst: lcd-rst {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	ppvar_lcd_en: ppvar-lcd-en {
+		pinmux {
+			pins = "gpio88";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio88";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	pp1800_disp_on: pp1800-disp-on {
+		pinmux {
+			pins = "gpio86";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio86";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
-- 
2.31.0


  parent reply	other threads:[~2022-05-10 22:46 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-05-10 22:44 [PATCH v5 1/5] arm64: dts: qcom: sc7180: Add wormdingler dts files Joseph S. Barrera III
2022-05-10 22:44 ` [PATCH v5 2/5] arm64: dts: qcom: sc7180: Add mrbland " Joseph S. Barrera III
2022-05-10 22:44 ` Joseph S. Barrera III [this message]
2022-05-18 13:52   ` [PATCH v5 3/5] arm64: dts: qcom: sc7180: Add quackingstick " Doug Anderson
2022-05-10 22:44 ` [PATCH v5 4/5] arm64: dts: qcom: sc7180: Add pazquel " Joseph S. Barrera III
2022-05-10 22:44 ` [PATCH v5 5/5] arm64: dts: qcom: sc7180: Add kingoftown " Joseph S. Barrera III
2022-05-12 22:19 ` [PATCH v5 1/5] arm64: dts: qcom: sc7180: Add wormdingler " Doug Anderson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220510154406.v5.3.I0977b1a08830d0caa8bfb1bdedb4ecceac709a7f@changeid \
    --to=joebar@chromium.org \
    --cc=agross@kernel.org \
    --cc=amstan@chromium.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dianders@chromium.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.