[merged mm-stable] kasan-move-boot-parameters-section-in-documentation.patch removed from -mm tree

[Andrew Morton <akpm@linux-foundation.org>]

The quilt patch titled
     Subject: kasan: move boot parameters section in documentation
has been removed from the -mm tree.  Its filename was
     kasan-move-boot-parameters-section-in-documentation.patch

This patch was dropped because it was merged into the mm-stable branch\nof git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

------------------------------------------------------
From: Andrey Konovalov <andreyknvl@google.com>
Subject: kasan: move boot parameters section in documentation

Move the "Boot parameters" section in KASAN documentation next to the
section that describes KASAN build options.

No content changes.

Link: https://lkml.kernel.org/r/870628e1293b4f44edf7cbcb92374ff9eb7503d7.1652203271.git.andreyknvl@google.com
Link: https://lkml.kernel.org/r/ec9c923f35e7c5312836c4624a7f317dc1ee2c1c.1652123204.git.andreyknvl@google.com
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Marco Elver <elver@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
---

 Documentation/dev-tools/kasan.rst |   82 ++++++++++++++--------------
 1 file changed, 41 insertions(+), 41 deletions(-)

--- a/Documentation/dev-tools/kasan.rst~kasan-move-boot-parameters-section-in-documentation
+++ a/Documentation/dev-tools/kasan.rst
@@ -94,6 +94,47 @@ To include alloc and free stack traces o
 enable ``CONFIG_STACKTRACE``. To include alloc and free stack traces of affected
 physical pages, enable ``CONFIG_PAGE_OWNER`` and boot with ``page_owner=on``.
 
+Boot parameters
+~~~~~~~~~~~~~~~
+
+KASAN is affected by the generic ``panic_on_warn`` command line parameter.
+When it is enabled, KASAN panics the kernel after printing a bug report.
+
+By default, KASAN prints a bug report only for the first invalid memory access.
+With ``kasan_multi_shot``, KASAN prints a report on every invalid access. This
+effectively disables ``panic_on_warn`` for KASAN reports.
+
+Alternatively, independent of ``panic_on_warn``, the ``kasan.fault=`` boot
+parameter can be used to control panic and reporting behaviour:
+
+- ``kasan.fault=report`` or ``=panic`` controls whether to only print a KASAN
+  report or also panic the kernel (default: ``report``). The panic happens even
+  if ``kasan_multi_shot`` is enabled.
+
+Hardware Tag-Based KASAN mode (see the section about various modes below) is
+intended for use in production as a security mitigation. Therefore, it supports
+additional boot parameters that allow disabling KASAN or controlling features:
+
+- ``kasan=off`` or ``=on`` controls whether KASAN is enabled (default: ``on``).
+
+- ``kasan.mode=sync``, ``=async`` or ``=asymm`` controls whether KASAN
+  is configured in synchronous, asynchronous or asymmetric mode of
+  execution (default: ``sync``).
+  Synchronous mode: a bad access is detected immediately when a tag
+  check fault occurs.
+  Asynchronous mode: a bad access detection is delayed. When a tag check
+  fault occurs, the information is stored in hardware (in the TFSR_EL1
+  register for arm64). The kernel periodically checks the hardware and
+  only reports tag faults during these checks.
+  Asymmetric mode: a bad access is detected synchronously on reads and
+  asynchronously on writes.
+
+- ``kasan.vmalloc=off`` or ``=on`` disables or enables tagging of vmalloc
+  allocations (default: ``on``).
+
+- ``kasan.stacktrace=off`` or ``=on`` disables or enables alloc and free stack
+  traces collection (default: ``on``).
+
 Error reports
 ~~~~~~~~~~~~~
 
@@ -208,47 +249,6 @@ traces point to places in code that inte
 directly present in the bad access stack trace. Currently, this includes
 call_rcu() and workqueue queuing.
 
-Boot parameters
-~~~~~~~~~~~~~~~
-
-KASAN is affected by the generic ``panic_on_warn`` command line parameter.
-When it is enabled, KASAN panics the kernel after printing a bug report.
-
-By default, KASAN prints a bug report only for the first invalid memory access.
-With ``kasan_multi_shot``, KASAN prints a report on every invalid access. This
-effectively disables ``panic_on_warn`` for KASAN reports.
-
-Alternatively, independent of ``panic_on_warn``, the ``kasan.fault=`` boot
-parameter can be used to control panic and reporting behaviour:
-
-- ``kasan.fault=report`` or ``=panic`` controls whether to only print a KASAN
-  report or also panic the kernel (default: ``report``). The panic happens even
-  if ``kasan_multi_shot`` is enabled.
-
-Hardware Tag-Based KASAN mode (see the section about various modes below) is
-intended for use in production as a security mitigation. Therefore, it supports
-additional boot parameters that allow disabling KASAN or controlling features:
-
-- ``kasan=off`` or ``=on`` controls whether KASAN is enabled (default: ``on``).
-
-- ``kasan.mode=sync``, ``=async`` or ``=asymm`` controls whether KASAN
-  is configured in synchronous, asynchronous or asymmetric mode of
-  execution (default: ``sync``).
-  Synchronous mode: a bad access is detected immediately when a tag
-  check fault occurs.
-  Asynchronous mode: a bad access detection is delayed. When a tag check
-  fault occurs, the information is stored in hardware (in the TFSR_EL1
-  register for arm64). The kernel periodically checks the hardware and
-  only reports tag faults during these checks.
-  Asymmetric mode: a bad access is detected synchronously on reads and
-  asynchronously on writes.
-
-- ``kasan.vmalloc=off`` or ``=on`` disables or enables tagging of vmalloc
-  allocations (default: ``on``).
-
-- ``kasan.stacktrace=off`` or ``=on`` disables or enables alloc and free stack
-  traces collection (default: ``on``).
-
 Implementation details
 ----------------------
 
_

Patches currently in -mm which might be from andreyknvl@google.com are