All of lore.kernel.org
 help / color / mirror / Atom feed
From: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <bjorn.andersson@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	Marijn Suijten <marijn.suijten@somainline.org>
Subject: [PATCH v7 11/11] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support
Date: Sat, 21 May 2022 23:27:08 +0300	[thread overview]
Message-ID: <20220521202708.1509308-12-dmitry.baryshkov@linaro.org> (raw)
In-Reply-To: <20220521202708.1509308-1-dmitry.baryshkov@linaro.org>

The IFC6560 is a board from Inforce Computing, built around the SDA660
SoC. This patch describes core clocks, some regulators from the two
PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.

The regulator settings are inherited from prior work by Konrad Dybcio
and AngeloGioacchino Del Regno.

Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 .../boot/dts/qcom/sda660-inforce-ifc6560.dts  | 461 ++++++++++++++++++
 2 files changed, 462 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 2f8aec2cc6db..12bb2f8bdac2 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
diff --git a/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
new file mode 100644
index 000000000000..28050bc5f081
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/ {
+	model = "Inforce 6560 Single Board Computer";
+	compatible = "inforce,ifc6560", "qcom,sda660";
+	chassis-type = "embedded"; /* SBC */
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		volup {
+			label = "Volume Up";
+			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	/*
+	 * Until we hook up type-c detection, we
+	 * have to stick with this. But it works.
+	 */
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	v3p3_bck_bst: v3p3-bck-bst-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3p3_bck_bst";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v1p2_ldo: v1p2-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p2_ldo";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v5p0_boost: v5p0-boost-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v5p0_boost";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/ifc6560/adsp.mbn";
+};
+
+&blsp_i2c6 {
+	status = "okay";
+
+	adv7533: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>, <0x66>;
+		reg-names = "main", "edid";
+
+		interrupt-parent = <&pm660l_gpios>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+		/*
+		 * Limit to 3 lanes to prevent the bridge from changing amount
+		 * of lanes in the fly. MSM DSI host doesn't like that.
+		 */
+		adi,dsi-lanes = <3>;
+		avdd-supply = <&vreg_l13a_1p8>;
+		dvdd-supply = <&vreg_l13a_1p8>;
+		pvdd-supply = <&vreg_l13a_1p8>;
+		a2vdd-supply = <&vreg_l13a_1p8>;
+		v3p3-supply = <&v3p3_bck_bst>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp1_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_l13a_1p8>;
+		vddxo-supply = <&vreg_l9a_1p8>;
+		vddrf-supply = <&vreg_l6a_1p3>;
+		vddch0-supply = <&vreg_l19a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l1a_1p225>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&adv7533_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vcca-supply = <&vreg_l1b_0p925>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmss_smmu {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEUP>;
+};
+
+&qusb2phy0 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&qusb2phy1 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&rpm_requests {
+	pm660-regulators {
+		compatible = "qcom,rpm-pm660-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+		vdd_l5-supply = <&vreg_s2b_1p05>;
+		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+		vreg_s4a_2p04: s4 {
+			regulator-min-microvolt = <1805000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+		};
+
+		vreg_s5a_1p35: s5 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1a_1p225: l1 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a_1p3: l6 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1368000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l8a_1p8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-system-load = <325000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1804000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13a_1p8: l13 {
+			/* This gives power to the LPDDR4: never turn it off! */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1944000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vreg_l19a_3p3: l19 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pm660l-regulators {
+		compatible = "qcom,rpm-pm660l-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+		vdd_l2-supply = <&vreg_bob>;
+		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+		vdd_l4_l6-supply = <&vreg_bob>;
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_s2b_1p05: s2 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1b_0p925: l1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <925000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l2b_2p95: l2 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4b_2p95: l4 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+
+			regulator-min-microamp = <200>;
+			regulator-max-microamp = <600000>;
+			regulator-system-load = <570000>;
+			regulator-allow-set-load;
+		};
+
+		/*
+		 * Downstream specifies a range of 1721-3600mV,
+		 * but the only assigned consumers are SDHCI2 VMMC
+		 * and Coresight QPDI that both request pinned 2.95V.
+		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
+		 * make the mmc driver happy.
+		 */
+		vreg_l5b_2p95: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-system-load = <800000>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7b_3p125: l7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3125000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8b_3p3: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3624000>;
+			regulator-enable-ramp-delay = <500>;
+			regulator-ramp-delay = <0>;
+		};
+	};
+};
+
+&sdc2_state_on {
+	sd-cd {
+		pins = "gpio54";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+};
+
+&sdc2_state_off {
+	sd-cd {
+		pins = "gpio54";
+		bias-disable;
+		drive-strength = <2>;
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+
+	vmmc-supply = <&vreg_l4b_2p95>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&vreg_l5b_2p95>;
+	vqmmc-supply = <&vreg_l2b_2p95>;
+
+	cd-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+	no-sdio;
+	no-emmc;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <8 4>;
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
+};
-- 
2.35.1


  parent reply	other threads:[~2022-05-21 20:27 UTC|newest]

Thread overview: 15+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-05-21 20:26 [PATCH v7 00/11] arm64: dts: qcom: " Dmitry Baryshkov
2022-05-21 20:26 ` [PATCH v7 01/11] arm64: dts: qcom: sdm630: disable dsi0/dsi0_phy by default Dmitry Baryshkov
2022-05-21 20:26 ` [PATCH v7 02/11] arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy " Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 03/11] arm64: dts: qcom: sdm630: disable GPU " Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 04/11] arm64: dts: qcom: sdm630: fix the qusb2phy ref clock Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 05/11] arm64: dts: qcom: sdm630: rename qusb2phy to qusb2phy0 Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 06/11] arm64: dts: qcom: sdm630: add second (HS) USB host support Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 07/11] arm64: dts: qcom: sdm630: fix gpu's interconnect path Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 08/11] arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf Dmitry Baryshkov
2022-05-22 22:22   ` Marijn Suijten
2022-05-21 20:27 ` [PATCH v7 09/11] arm64: dts: qcom: sdm660: move SDHC2 card detect pinconf to board files Dmitry Baryshkov
2022-05-21 20:27 ` [PATCH v7 10/11] dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board Dmitry Baryshkov
2022-05-24  2:04   ` Rob Herring
2022-05-21 20:27 ` Dmitry Baryshkov [this message]
2022-07-03  3:56 ` [PATCH v7 00/11] arm64: dts: qcom: initial Inforce IFC6560 board support Bjorn Andersson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220521202708.1509308-12-dmitry.baryshkov@linaro.org \
    --to=dmitry.baryshkov@linaro.org \
    --cc=agross@kernel.org \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=marijn.suijten@somainline.org \
    --cc=robh+dt@kernel.org \
    --subject='Re: [PATCH v7 11/11] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support' \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.