This work is largely based on the previous work by Bjorn Andersson ([1]) Changes since v6: - Rebase on top of linux-next - Reorder last two patches to have bindings come before the dts (Marijn) - Add missed R-b tags, excuse me Marijn. Changes since v5: - Drop icc patch, as there are questions whether the original paths are valid. It will be submitted separately. Changes since v4: - Remove unused mdp and sd-card-det-n DT nodes from the ifc6560 dts (thanks to Konrad). Changes since v3 (most points based on review by Marijn): - Fixed a typo in dsi0 patch - Fixed indentation here and there - Renamed qusb2phy to qusb2phy0 to play better with qusb2phy1 - Fixed the ICC path for the GPU - Fixed sdhc2 pinconf for sdm636-sony-xperia-ganges-mermaid - Moved SDHC2 card detect gpio pin to board files Changes since v2: - Removed useless enablement of mdp node from the board file. It is already enabled in the SoC dtsi file. Changes since v1 (mostly based on Kondrad's review): - Also disabled dsi0/dsi0 phy in sdm630.dtsi - Removed the clock from BAM DMA devices rather than disabling them completely - Replaced numbers with symbolic names for interconnects in sdm630.dtsi - Switched to "qcom,sda660" as a fallback compatible string - Added dt-bindings for the qcom,sda660 compat - Removed extra nesting level from the adsp firmware path - Replaced numbers with proper symbolic names in the board file - Added chassis-type property - Changed the order of blsp entries in the board file - Removed spurious newlines - Changed the order of regulator properties - Changed the DSI data-lines to list all four lanes. Still use just three lanes for the adv bridge (and describe the reason in the comment) Changes since Bjorn's v2: - Disable dsi1, dsi1 phy, GPU by default in sdm660.dtsi/sdm630.dtsi - Fix qusb2phy ref clock - Added USB2 host support to sdm630.dtsi - Renamed DTS to follow SoC-vendor-board pattern - Fixed vph_pwr voltage - Removed extra/unrelated comments - Added keys, USB2, USB3, - Added configuration for the attached HDMI bridge - Enabled MDP, MDSS and DSI0/DSI0 PHY devices - Removed uart pinctrl and /reserved-mem nodes (present in main dtsi file) - Added card detection for the SDCC2 - Disabled BLSP BAM DMA devices, they make the board reset during boot [1] https://lore.kernel.org/linux-arm-msm/20210825221110.1498718-1-bjorn.andersson@linaro.org/#t Dmitry Baryshkov (11): arm64: dts: qcom: sdm630: disable dsi0/dsi0_phy by default arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default arm64: dts: qcom: sdm630: disable GPU by default arm64: dts: qcom: sdm630: fix the qusb2phy ref clock arm64: dts: qcom: sdm630: rename qusb2phy to qusb2phy0 arm64: dts: qcom: sdm630: add second (HS) USB host support arm64: dts: qcom: sdm630: fix gpu's interconnect path arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf arm64: dts: qcom: sdm660: move SDHC2 card detect pinconf to board files dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support .../devicetree/bindings/arm/qcom.yaml | 6 + arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sda660-inforce-ifc6560.dts | 461 ++++++++++++++++++ .../dts/qcom/sdm630-sony-xperia-nile.dtsi | 18 +- arch/arm64/boot/dts/qcom/sdm630.dtsi | 81 ++- .../sdm636-sony-xperia-ganges-mermaid.dts | 2 +- .../boot/dts/qcom/sdm660-xiaomi-lavender.dts | 18 +- arch/arm64/boot/dts/qcom/sdm660.dtsi | 3 + 8 files changed, 571 insertions(+), 19 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts -- 2.35.1
Follow the typical practice and keep DSI0/DSI0 PHY disabled by default. They should be enabled in the board DT files. No existing boards use them at this moment. Suggested-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index b72e8e6c52f3..80d5eae9bc75 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -1563,6 +1563,8 @@ dsi0: dsi@c994000 { phys = <&dsi0_phy>; phy-names = "dsi"; + status = "disabled"; + ports { #address-cells = <1>; #size-cells = <0>; @@ -1596,6 +1598,7 @@ dsi0_phy: dsi-phy@c994400 { clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>; clock-names = "iface", "ref"; + status = "disabled"; }; }; -- 2.35.1
Follow the typical practice and keep DSI1/DSI1 PHY disabled by default. They should be enabled in the board DT files. No existing boards use them at this moment. Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm660.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm660.dtsi b/arch/arm64/boot/dts/qcom/sdm660.dtsi index 1d748c5305f4..c92f1cef3d3c 100644 --- a/arch/arm64/boot/dts/qcom/sdm660.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm660.dtsi @@ -192,6 +192,8 @@ dsi1: dsi@c996000 { phys = <&dsi1_phy>; phy-names = "dsi"; + status = "disabled"; + ports { #address-cells = <1>; #size-cells = <0>; @@ -225,6 +227,7 @@ dsi1_phy: dsi-phy@c996400 { clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>; clock-names = "iface", "ref"; + status = "disabled"; }; }; -- 2.35.1
The SoC's device tree file disables gpucc and adreno's SMMU by default. So let's disable the GPU too. Moreover it looks like SMMU might be not usable without additional patches (which means that GPU is unusable too). No board uses GPU at this moment. Fixes: 5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration") Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 80d5eae9bc75..ac4e688a717a 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -1050,6 +1050,8 @@ adreno_gpu: gpu@5000000 { operating-points-v2 = <&gpu_sdm630_opp_table>; + status = "disabled"; + gpu_sdm630_opp_table: opp-table { compatible = "operating-points-v2"; opp-775000000 { -- 2.35.1
According to the downstram DT file, the qusb2phy ref clock should be GCC_RX0_USB2_CLKREF_CLK, not GCC_RX1_USB2_CLKREF_CLK. Fixes: c65a4ed2ea8b ("arm64: dts: qcom: sdm630: Add USB configuration") Cc: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index ac4e688a717a..0ffd8e382d8c 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -1266,7 +1266,7 @@ qusb2phy: phy@c012000 { #phy-cells = <0>; clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, - <&gcc GCC_RX1_USB2_CLKREF_CLK>; + <&gcc GCC_RX0_USB2_CLKREF_CLK>; clock-names = "cfg_ahb", "ref"; resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; -- 2.35.1
In preparation to adding second USB host/PHY pair, change first USB PHY's label to qusb2phy0. Suggested-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi | 2 +- arch/arm64/boot/dts/qcom/sdm630.dtsi | 4 ++-- arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts | 2 +- 3 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi index 42af1fade461..00baacf28c63 100644 --- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi @@ -224,7 +224,7 @@ &pon_resin { linux,code = <KEY_VOLUMEUP>; }; -&qusb2phy { +&qusb2phy0 { status = "okay"; vdd-supply = <&vreg_l1b_0p925>; diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 0ffd8e382d8c..f4d09784ff29 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -1254,13 +1254,13 @@ usb3_dwc3: usb@a800000 { * haven't seen any devices making use of it. */ maximum-speed = "high-speed"; - phys = <&qusb2phy>; + phys = <&qusb2phy0>; phy-names = "usb2-phy"; snps,hird-threshold = /bits/ 8 <0>; }; }; - qusb2phy: phy@c012000 { + qusb2phy0: phy@c012000 { compatible = "qcom,sdm660-qusb2-phy"; reg = <0x0c012000 0x180>; #phy-cells = <0>; diff --git a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts index dcbaacf18f66..9280c1f0c334 100644 --- a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts +++ b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts @@ -103,7 +103,7 @@ &pon_resin { linux,code = <KEY_VOLUMEDOWN>; }; -&qusb2phy { +&qusb2phy0 { status = "okay"; vdd-supply = <&vreg_l1b_0p925>; -- 2.35.1
Add DT entries for the second DWC3 USB host, which is limited to the USB2.0 (HighSpeed), and the corresponding QUSB PHY. Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 55 ++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index f4d09784ff29..11ec8b3cfe38 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -1274,6 +1274,20 @@ qusb2phy0: phy@c012000 { status = "disabled"; }; + qusb2phy1: phy@c014000 { + compatible = "qcom,sdm660-qusb2-phy"; + reg = <0x0c014000 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_RX1_USB2_CLKREF_CLK>; + clock-names = "cfg_ahb", "ref"; + + resets = <&gcc GCC_QUSB2PHY_SEC_BCR>; + nvmem-cells = <&qusb2_hstx_trim>; + status = "disabled"; + }; + sdhc_2: sdhci@c084000 { compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; reg = <0x0c084000 0x1000>; @@ -1379,6 +1393,47 @@ opp-384000000 { }; }; + usb2: usb@c2f8800 { + compatible = "qcom,sdm660-dwc3", "qcom,dwc3"; + reg = <0x0c2f8800 0x400>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_CFG_NOC_USB2_AXI_CLK>, + <&gcc GCC_USB20_MASTER_CLK>, + <&gcc GCC_USB20_MOCK_UTMI_CLK>, + <&gcc GCC_USB20_SLEEP_CLK>; + clock-names = "cfg_noc", "core", + "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>, + <&gcc GCC_USB20_MASTER_CLK>; + assigned-clock-rates = <19200000>, <60000000>; + + interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hs_phy_irq"; + + qcom,select-utmi-as-pipe-clk; + + resets = <&gcc GCC_USB_20_BCR>; + + usb2_dwc3: usb@c200000 { + compatible = "snps,dwc3"; + reg = <0x0c200000 0xc8d0>; + interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + + /* This is the HS-only host */ + maximum-speed = "high-speed"; + phys = <&qusb2phy1>; + phy-names = "usb2-phy"; + snps,hird-threshold = /bits/ 8 <0>; + }; + }; + mmcc: clock-controller@c8c0000 { compatible = "qcom,mmcc-sdm630"; reg = <0x0c8c0000 0x40000>; -- 2.35.1
ICC path for the GPU incorrectly states <&gnoc 1 &bimc 5>, which is a path from SLAVE_GNOC_BIMC to SLAVE_EBI. According to the downstream kernel sources, the GPU uses MASTER_OXILI here, which is equivalent to <&bimc 1 ...>. While we are at it, use defined names instead of the numbers for this interconnect path. Fixes: 5cf69dcbec8b ("arm64: dts: qcom: sdm630: Add Adreno 508 GPU configuration") Reported-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 11ec8b3cfe38..1c887b9055b3 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -8,6 +8,7 @@ #include <dt-bindings/clock/qcom,gpucc-sdm660.h> #include <dt-bindings/clock/qcom,mmcc-sdm660.h> #include <dt-bindings/clock/qcom,rpmcc.h> +#include <dt-bindings/interconnect/qcom,sdm660.h> #include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> @@ -1045,7 +1046,7 @@ adreno_gpu: gpu@5000000 { nvmem-cells = <&gpu_speed_bin>; nvmem-cell-names = "speed_bin"; - interconnects = <&gnoc 1 &bimc 5>; + interconnects = <&bimc MASTER_OXILI &bimc SLAVE_EBI>; interconnect-names = "gfx-mem"; operating-points-v2 = <&gpu_sdm630_opp_table>; -- 2.35.1
Fix the device tree node in the &sdc2_state_on override. The sdm630 uses 'clk' rather than 'pinconf-clk'. Fixes: 4c1d849ec047 ("arm64: dts: qcom: sdm630-xperia: Retire sdm630-sony-xperia-ganges.dtsi") Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts index b96da53f2f1e..58f687fc49e0 100644 --- a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts +++ b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts @@ -19,7 +19,7 @@ / { }; &sdc2_state_on { - pinconf-clk { + clk { drive-strength = <14>; }; }; -- 2.35.1
This results in dts duplication, but per mutual agreement card detect pin configuration belongs to the board files. Move it from the SoC dtsi to the board DT files. Suggested-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- .../boot/dts/qcom/sdm630-sony-xperia-nile.dtsi | 16 ++++++++++++++++ arch/arm64/boot/dts/qcom/sdm630.dtsi | 12 ------------ .../boot/dts/qcom/sdm660-xiaomi-lavender.dts | 16 ++++++++++++++++ 3 files changed, 32 insertions(+), 12 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi index 00baacf28c63..ccde9951e4fb 100644 --- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi @@ -549,6 +549,22 @@ vreg_l19a_3p3: l19 { }; }; +&sdc2_state_on { + sd-cd { + pins = "gpio54"; + bias-pull-up; + drive-strength = <2>; + }; +}; + +&sdc2_state_off { + sd-cd { + pins = "gpio54"; + bias-disable; + drive-strength = <2>; + }; +}; + &sdhc_1 { status = "okay"; supports-cqe; diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 1c887b9055b3..55de345895e6 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -983,12 +983,6 @@ data { bias-pull-up; drive-strength = <10>; }; - - sd-cd { - pins = "gpio54"; - bias-pull-up; - drive-strength = <2>; - }; }; sdc2_state_off: sdc2-off { @@ -1009,12 +1003,6 @@ data { bias-pull-up; drive-strength = <2>; }; - - sd-cd { - pins = "gpio54"; - bias-disable; - drive-strength = <2>; - }; }; }; diff --git a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts index 9280c1f0c334..2b1216502eb0 100644 --- a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts +++ b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts @@ -363,6 +363,22 @@ vreg_l19a_3p3: l19 { }; }; +&sdc2_state_on { + sd-cd { + pins = "gpio54"; + bias-pull-up; + drive-strength = <2>; + }; +}; + +&sdc2_state_off { + sd-cd { + pins = "gpio54"; + bias-disable; + drive-strength = <2>; + }; +}; + &sdhc_1 { status = "okay"; supports-cqe; -- 2.35.1
Add binding documentation for the Inforce IFC6560 board which uses Snapdragon SDA660. Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index 5c06d1bfc046..29ce543da391 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -44,6 +44,7 @@ description: | sc7280 sc8180x sc8280xp + sda660 sdm630 sdm632 sdm660 @@ -241,6 +242,11 @@ properties: - qcom,sc8280xp-qrd - const: qcom,sc8280xp + - items: + - enum: + - inforce,ifc6560 + - const: qcom,sda660 + - items: - enum: - fairphone,fp3 -- 2.35.1
The IFC6560 is a board from Inforce Computing, built around the SDA660 SoC. This patch describes core clocks, some regulators from the two PMICs, debug uart, storage, bluetooth and audio DSP remoteproc. The regulator settings are inherited from prior work by Konrad Dybcio and AngeloGioacchino Del Regno. Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sda660-inforce-ifc6560.dts | 461 ++++++++++++++++++ 2 files changed, 462 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 2f8aec2cc6db..12bb2f8bdac2 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -89,6 +89,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc7280-herobrine-villager-r0.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-idp2.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7280-crd-r3.dtb +dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-ganges-kirin.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-discovery.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm630-sony-xperia-nile-pioneer.dtb diff --git a/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts new file mode 100644 index 000000000000..28050bc5f081 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts @@ -0,0 +1,461 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Ltd. + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org> + * Copyright (c) 2020, AngeloGioacchino Del Regno + * <angelogioacchino.delregno@somainline.org> + */ + +/dts-v1/; + +#include "sdm660.dtsi" +#include "pm660.dtsi" +#include "pm660l.dtsi" + +/ { + model = "Inforce 6560 Single Board Computer"; + compatible = "inforce,ifc6560", "qcom,sda660"; + chassis-type = "embedded"; /* SBC */ + + aliases { + serial0 = &blsp1_uart2; + serial1 = &blsp2_uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + volup { + label = "Volume Up"; + gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + }; + }; + + /* + * Until we hook up type-c detection, we + * have to stick with this. But it works. + */ + extcon_usb: extcon-usb { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>; + }; + + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <&adv7533_out>; + }; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3800000>; + regulator-max-microvolt = <3800000>; + + regulator-always-on; + regulator-boot-on; + }; + + v3p3_bck_bst: v3p3-bck-bst-regulator { + compatible = "regulator-fixed"; + regulator-name = "v3p3_bck_bst"; + + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + vin-supply = <&vph_pwr>; + }; + + v1p2_ldo: v1p2-ldo-regulator { + compatible = "regulator-fixed"; + regulator-name = "v1p2_ldo"; + + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + vin-supply = <&vph_pwr>; + }; + + v5p0_boost: v5p0-boost-regulator { + compatible = "regulator-fixed"; + regulator-name = "v5p0_boost"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + vin-supply = <&vph_pwr>; + }; +}; + +&adsp_pil { + firmware-name = "qcom/ifc6560/adsp.mbn"; +}; + +&blsp_i2c6 { + status = "okay"; + + adv7533: hdmi@39 { + compatible = "adi,adv7535"; + reg = <0x39>, <0x66>; + reg-names = "main", "edid"; + + interrupt-parent = <&pm660l_gpios>; + interrupts = <11 IRQ_TYPE_EDGE_FALLING>; + + clocks = <&rpmcc RPM_SMD_BB_CLK2>; + clock-names = "cec"; + /* + * Limit to 3 lanes to prevent the bridge from changing amount + * of lanes in the fly. MSM DSI host doesn't like that. + */ + adi,dsi-lanes = <3>; + avdd-supply = <&vreg_l13a_1p8>; + dvdd-supply = <&vreg_l13a_1p8>; + pvdd-supply = <&vreg_l13a_1p8>; + a2vdd-supply = <&vreg_l13a_1p8>; + v3p3-supply = <&v3p3_bck_bst>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + adv7533_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + adv7533_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + }; + }; +}; + +&blsp1_dma { + /* + * The board will lock up if we toggle the BLSP clock, unless the + * BAM DMA interconnects support is in place. + */ + /delete-property/ clocks; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp2_dma { + /* + * The board will lock up if we toggle the BLSP clock, unless the + * BAM DMA interconnects support is in place. + */ + /delete-property/ clocks; +}; + +&blsp2_uart1 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_l13a_1p8>; + vddxo-supply = <&vreg_l9a_1p8>; + vddrf-supply = <&vreg_l6a_1p3>; + vddch0-supply = <&vreg_l19a_3p3>; + max-speed = <3200000>; + }; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l1a_1p225>; +}; + +&dsi0_out { + remote-endpoint = <&adv7533_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vcca-supply = <&vreg_l1b_0p925>; +}; + +&mdss { + status = "okay"; +}; + +&mmss_smmu { + status = "okay"; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + status = "okay"; + + linux,code = <KEY_VOLUMEUP>; +}; + +&qusb2phy0 { + status = "okay"; + + vdd-supply = <&vreg_l1b_0p925>; + vdda-phy-dpdm-supply = <&vreg_l7b_3p125>; +}; + +&qusb2phy1 { + status = "okay"; + + vdd-supply = <&vreg_l1b_0p925>; + vdda-phy-dpdm-supply = <&vreg_l7b_3p125>; +}; + +&rpm_requests { + pm660-regulators { + compatible = "qcom,rpm-pm660-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + + vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>; + vdd_l2_l3-supply = <&vreg_s2b_1p05>; + vdd_l5-supply = <&vreg_s2b_1p05>; + vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>; + vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>; + + vreg_s4a_2p04: s4 { + regulator-min-microvolt = <1805000>; + regulator-max-microvolt = <2040000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + regulator-always-on; + }; + + vreg_s5a_1p35: s5 { + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1350000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + }; + + vreg_l1a_1p225: l1 { + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1250000>; + regulator-enable-ramp-delay = <250>; + regulator-allow-set-load; + }; + + vreg_l6a_1p3: l6 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1368000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l8a_1p8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-system-load = <325000>; + regulator-allow-set-load; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1804000>; + regulator-max-microvolt = <1896000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l13a_1p8: l13 { + /* This gives power to the LPDDR4: never turn it off! */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1944000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-always-on; + regulator-boot-on; + }; + + vreg_l19a_3p3: l19 { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3400000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + }; + + pm660l-regulators { + compatible = "qcom,rpm-pm660l-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + + vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>; + vdd_l2-supply = <&vreg_bob>; + vdd_l3_l5_l7_l8-supply = <&vreg_bob>; + vdd_l4_l6-supply = <&vreg_bob>; + vdd_bob-supply = <&vph_pwr>; + + vreg_s2b_1p05: s2 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-enable-ramp-delay = <200>; + regulator-ramp-delay = <0>; + }; + + vreg_l1b_0p925: l1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <925000>; + regulator-enable-ramp-delay = <250>; + regulator-allow-set-load; + }; + + vreg_l2b_2p95: l2 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <3100000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l4b_2p95: l4 { + regulator-min-microvolt = <2944000>; + regulator-max-microvolt = <2952000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + + regulator-min-microamp = <200>; + regulator-max-microamp = <600000>; + regulator-system-load = <570000>; + regulator-allow-set-load; + }; + + /* + * Downstream specifies a range of 1721-3600mV, + * but the only assigned consumers are SDHCI2 VMMC + * and Coresight QPDI that both request pinned 2.95V. + * Tighten the range to 1.8-3.328 (closest to 3.3) to + * make the mmc driver happy. + */ + vreg_l5b_2p95: l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3328000>; + regulator-enable-ramp-delay = <250>; + regulator-system-load = <800000>; + regulator-ramp-delay = <0>; + regulator-allow-set-load; + }; + + vreg_l7b_3p125: l7 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3125000>; + regulator-enable-ramp-delay = <250>; + }; + + vreg_l8b_3p3: l8 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3400000>; + regulator-enable-ramp-delay = <250>; + regulator-ramp-delay = <0>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3624000>; + regulator-enable-ramp-delay = <500>; + regulator-ramp-delay = <0>; + }; + }; +}; + +&sdc2_state_on { + sd-cd { + pins = "gpio54"; + bias-pull-up; + drive-strength = <2>; + }; +}; + +&sdc2_state_off { + sd-cd { + pins = "gpio54"; + bias-disable; + drive-strength = <2>; + }; +}; + +&sdhc_1 { + status = "okay"; + supports-cqe; + + vmmc-supply = <&vreg_l4b_2p95>; + vqmmc-supply = <&vreg_l8a_1p8>; + + mmc-ddr-1_8v; + mmc-hs400-1_8v; + mmc-hs400-enhanced-strobe; +}; + +&sdhc_2 { + status = "okay"; + + vmmc-supply = <&vreg_l5b_2p95>; + vqmmc-supply = <&vreg_l2b_2p95>; + + cd-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>; + no-sdio; + no-emmc; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <8 4>; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_dwc3 { + dr_mode = "host"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "peripheral"; + extcon = <&extcon_usb>; +}; -- 2.35.1
On 2022-05-21 23:27:05, Dmitry Baryshkov wrote: > Fix the device tree node in the &sdc2_state_on override. The sdm630 uses > 'clk' rather than 'pinconf-clk'. > > Fixes: 4c1d849ec047 ("arm64: dts: qcom: sdm630-xperia: Retire sdm630-sony-xperia-ganges.dtsi") > Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> > Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org> > --- > arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts | 2 +- > 1 file changed, 1 insertion(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts > index b96da53f2f1e..58f687fc49e0 100644 > --- a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts > +++ b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts > @@ -19,7 +19,7 @@ / { > }; > > &sdc2_state_on { > - pinconf-clk { > + clk { > drive-strength = <14>; > }; > }; > -- > 2.35.1 >
On Sat, 21 May 2022 23:27:07 +0300, Dmitry Baryshkov wrote:
> Add binding documentation for the Inforce IFC6560 board which uses
> Snapdragon SDA660.
>
> Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> ---
> Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++
> 1 file changed, 6 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
On Sat, 21 May 2022 23:26:57 +0300, Dmitry Baryshkov wrote:
> This work is largely based on the previous work by Bjorn Andersson ([1])
>
> Changes since v6:
> - Rebase on top of linux-next
> - Reorder last two patches to have bindings come before the dts (Marijn)
> - Add missed R-b tags, excuse me Marijn.
>
> [...]
Applied, thanks!
[01/11] arm64: dts: qcom: sdm630: disable dsi0/dsi0_phy by default
commit: 79d8e016fddfe0315c4b682a891b446ec748a6e5
[02/11] arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default
commit: 7d8ee8e5db53b99cb522dd5126dc80fa5726aa07
[03/11] arm64: dts: qcom: sdm630: disable GPU by default
commit: 1c047919763b4548381d1ab3320af1df66ab83df
[04/11] arm64: dts: qcom: sdm630: fix the qusb2phy ref clock
commit: 924bbd8dd60e094344711c3526a5b308d71dc008
[05/11] arm64: dts: qcom: sdm630: rename qusb2phy to qusb2phy0
commit: 696dea7e1c3a568b125baee98bbf6b8db09a7afb
[06/11] arm64: dts: qcom: sdm630: add second (HS) USB host support
commit: 8b6da22e6a44b597a0a4e2d60d81303090b6d24e
[07/11] arm64: dts: qcom: sdm630: fix gpu's interconnect path
commit: 3cd1c4f41d64a40ea6bc4575ae28e37542123d77
[08/11] arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf
commit: 3a04cec9cba393abfe70fc62e523f381c9baec2e
[09/11] arm64: dts: qcom: sdm660: move SDHC2 card detect pinconf to board files
commit: 5e9bc1ba7ace0793b62e612eb48b7774a13e7f74
[10/11] dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board
commit: bbd5a68919081d2fea6b0a6d6ab4c34effbf2847
[11/11] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support
commit: 34279d6e3f32c7b2dd1192d8ba3e1d28b6ac775e
Best regards,
--
Bjorn Andersson <bjorn.andersson@linaro.org>