Re: [PATCH v3 12/17] dt-bindings: PCI: dwc: Add Baikal-T1 PCIe Root Port bindings

[Serge Semin <fancer.lancer@gmail.com>]

On Wed, Jun 15, 2022 at 10:37:12AM -0600, Rob Herring wrote:
> On Fri, Jun 10, 2022 at 11:57:00AM +0300, Serge Semin wrote:
> > Baikal-T1 SoC is equipped with DWC PCIe v4.60a Root Port controller, which
> > link can be trained to work on up to Gen.3 speed over up to x4 lanes. The
> > controller is supposed to be fed up with four clock sources: DBI
> > peripheral clock, AXI application Tx/Rx clocks and external PHY/core
> > reference clock generating the 100MHz signal. In addition to that the
> > platform provide a way to reset each part of the controller:
> > sticky/non-sticky bits, host controller core, PIPE interface, PCS/PHY and
> > Hot/Power reset signal. The Root Port controller is equipped with multiple
> > IRQ lines like MSI, system AER, PME, HP, Bandwidth change, Link
> > equalization request and eDMA ones. The registers space is accessed over
> > the DBI interface. There can be no more than four inbound or outbound iATU
> > windows configured.
> > 
> > Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
> > 
> > ---
> > 
> > Changelog v2:
> > - Rename 'syscon' property to 'baikal,bt1-syscon'.
> > - Fix the 'compatible' property definition to being more specific about
> >   what strings are supposed to be used. Due to that we had to add the
> >   select property to evaluate the schema against the Baikal-T1 PCIe DT
> >   nodes only.
> > ---
> >  .../bindings/pci/baikal,bt1-pcie.yaml         | 154 ++++++++++++++++++
> >  1 file changed, 154 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml b/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml
> > new file mode 100644
> > index 000000000000..23bd1d0aa5c5
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/baikal,bt1-pcie.yaml
> > @@ -0,0 +1,154 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pci/baikal,bt1-pcie.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Baikal-T1 PCIe Root Port Controller
> > +
> > +maintainers:
> > +  - Serge Semin <fancer.lancer@gmail.com>
> > +
> > +description:
> > +  Embedded into Baikal-T1 SoC Root Complex controller. It's based on the
> > +  DWC RC PCIe v4.60a IP-core, which is configured to have just a single Root
> > +  Port function and is capable of establishing the link up to Gen.3 speed
> > +  on x4 lanes. It doesn't have embedded clock and reset control module, so
> > +  the proper interface initialization is supposed to be performed by software.
> > +
> > +select:
> > +  properties:
> > +    compatible:
> > +      contains:
> > +        const: baikal,bt1-pcie
> > +
> > +  required:
> > +    - compatible
> > +
> > +allOf:
> > +  - $ref: /schemas/pci/snps,dw-pcie.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    items:
> > +      - const: baikal,bt1-pcie
> > +      - const: snps,dw-pcie-4.60a
> 

> Pointless, you can read the version.

The IP-core version CSR was first introduced in v4.70a. So by using
the version-based compatible string I advertise the actual IP-core
version.

> 
> > +      - const: snps,dw-pcie
> 

> Pointless, because what can you do with this by itself?

In general many things. For instance implement some IP-core specific
quirks in the generic part of the PCIe subsystem, visually identify
the device origin, etc.

> 
> > +
> > +  reg:
> > +    description:
> > +      DBI, DBI2 and at least 4KB outbound iATU-capable region.
> > +    maxItems: 3
> > +
> > +  reg-names:
> > +    minItems: 3
> > +    maxItems: 3
> > +    items:
> > +      enum: [ dbi, dbi2, config ]
> 

> This should define the order.

Please, tell me why do you persist in the items being ordered? The
driver permits the relaxed order of the resources. Thus there is no
much need in such constraint. At least I can't find any.

> 
> > +
> > +  interrupts:
> > +    description:
> > +      MSI, AER, PME, Hot-plug, Link Bandwidth Management, Link Equalization
> > +      request and eight Read/Write eDMA IRQ lines are available.
> > +    maxItems: 14
> > +
> > +  interrupt-names:
> > +    minItems: 14
> > +    maxItems: 14
> > +    items:
> > +      oneOf:
> > +        - pattern: '^dma[0-7]$'
> > +        - enum: [ msi, aer, pme, hp, bw_mg, l_eq ]
> 

> Define the order.

Fourteen IRQs? dma0, dma1, dma2, ..., msi, aer, ..., l_eq?

> 
> > +
> > +  clocks:
> > +    description:
> > +      DBI (attached to the APB bus), AXI-bus master and slave interfaces
> > +      are fed up by the dedicated application clocks. A common reference
> > +      clock signal is supposed to be attached to the corresponding Ref-pad
> > +      of the SoC. It will be redistributed amongst the controller core
> > +      sub-modules (pipe, core, aux, etc).
> > +    minItems: 4
> > +    maxItems: 4
> > +
> > +  clock-names:
> > +    minItems: 4
> > +    maxItems: 4
> > +    items:
> > +      enum: [ dbi, mstr, slv, ref ]
> > +
> > +  resets:
> > +    description:
> > +      A comprehensive controller reset logic is supposed to be implemented
> > +      by software, so almost all the possible application and core reset
> > +      signals are exposed via the system CCU module.
> > +    minItems: 9
> > +    maxItems: 9
> > +
> > +  reset-names:
> > +    minItems: 9
> > +    maxItems: 9
> > +    items:
> > +      enum: [ mstr, slv, pwr, hot, phy, core, pipe, sticky, non-sticky ]
> > +
> > +  baikal,bt1-syscon:
> > +    $ref: /schemas/types.yaml#/definitions/phandle
> > +    description:
> > +      Phandle to the Baikal-T1 System Controller DT node. It's required to
> > +      access some additional PM, Reset-related and LTSSM signals.
> > +
> > +  num-lanes:
> > +    maximum: 4
> > +
> > +  max-link-speed:
> > +    maximum: 3
> > +
> 

> > +  num-ob-windows:
> > +    const: 4
> > +
> > +  num-ib-windows:
> > +    const: 4
> 
> Remove these. They are deprecated and shouldn't be in new bindings.

Aren't they deprecated in the framework of the DT nodes only?
Can't I still use them here to signify the number of iATU windows?

-Sergey

> 
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - reg-names
> > +  - interrupts
> > +  - interrupt-names
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    pcie@1f052000 {
> > +      compatible = "baikal,bt1-pcie", "snps,dw-pcie-4.60a", "snps,dw-pcie";
> > +      device_type = "pci";
> > +      reg = <0x1f052000 0x1000>, <0x1f053000 0x1000>, <0x1bdbf000 0x1000>;
> > +      reg-names = "dbi", "dbi2", "config";
> > +      #address-cells = <3>;
> > +      #size-cells = <2>;
> > +      ranges = <0x81000000 0 0x00000000 0x1bdb0000 0 0x00008000>,
> > +               <0x82000000 0 0x20000000 0x08000000 0 0x13db0000>;
> > +      bus-range = <0x0 0xff>;
> > +
> > +      interrupts = <0 80 4>, <0 81 4>, <0 82 4>, <0 83 4>,
> > +                   <0 84 4>, <0 85 4>, <0 86 4>, <0 87 4>,
> > +                   <0 88 4>, <0 89 4>, <0 90 4>, <0 91 4>,
> > +                   <0 92 4>, <0 93 4>;
> > +      interrupt-names = "dma0", "dma1", "dma2", "dma3", "dma4", "dma5", "dma6",
> > +                        "dma7", "msi", "aer", "pme", "hp", "bw_mg", "l_eq";
> > +
> > +      clocks = <&ccu_sys 1>, <&ccu_axi 6>, <&ccu_axi 7>, <&clk_pcie>;
> > +      clock-names = "dbi", "mstr", "slv", "ref";
> > +
> > +      resets = <&ccu_axi 6>, <&ccu_axi 7>, <&ccu_sys 7>, <&ccu_sys 10>,
> > +               <&ccu_sys 4>, <&ccu_sys 6>, <&ccu_sys 5>, <&ccu_sys 8>,
> > +               <&ccu_sys 9>;
> > +      reset-names = "mstr", "slv", "pwr", "hot", "phy", "core", "pipe",
> > +                    "sticky", "non-sticky";
> > +
> > +      reset-gpios = <&port0 0 1>;
> > +
> > +      num-lanes = <4>;
> > +      max-link-speed = <3>;
> > +    };
> > +...
> > -- 
> > 2.35.1
> > 
> >