All of lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH] serial: mvebu-uart: correctly report configured baudrate value
@ 2022-06-28 10:09 Pali Rohár
  2022-06-28 10:23 ` Ilpo Järvinen
  0 siblings, 1 reply; 3+ messages in thread
From: Pali Rohár @ 2022-06-28 10:09 UTC (permalink / raw)
  To: Ilpo Järvinen, Greg Kroah-Hartman, Jiri Slaby, Allen Yan,
	Miquel Raynal, Gregory CLEMENT
  Cc: linux-serial, linux-kernel

Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
be called with the baudrate value which was set to hardware. Linux then
report exact values via ioctl(TCGETS2) to userspace.

Change mvebu_uart_baud_rate_set() function to return baudrate value which
was set to hardware and propagate this value to above mentioned functions.

With this change userspace would see precise value in termios c_ospeed
field.

Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
---
 drivers/tty/serial/mvebu-uart.c | 25 +++++++++++++------------
 1 file changed, 13 insertions(+), 12 deletions(-)

diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
index 0429c2a54290..93489fe334d0 100644
--- a/drivers/tty/serial/mvebu-uart.c
+++ b/drivers/tty/serial/mvebu-uart.c
@@ -470,14 +470,14 @@ static void mvebu_uart_shutdown(struct uart_port *port)
 	}
 }
 
-static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
+static unsigned int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
 {
 	unsigned int d_divisor, m_divisor;
 	unsigned long flags;
 	u32 brdv, osamp;
 
 	if (!port->uartclk)
-		return -EOPNOTSUPP;
+		return 0;
 
 	/*
 	 * The baudrate is derived from the UART clock thanks to divisors:
@@ -548,7 +548,7 @@ static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
 			(m_divisor << 16) | (m_divisor << 24);
 	writel(osamp, port->membase + UART_OSAMP);
 
-	return 0;
+	return DIV_ROUND_CLOSEST(port->uartclk, d_divisor * m_divisor);
 }
 
 static void mvebu_uart_set_termios(struct uart_port *port,
@@ -587,15 +587,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
 	max_baud = port->uartclk / 80;
 
 	baud = uart_get_baud_rate(port, termios, old, min_baud, max_baud);
-	if (mvebu_uart_baud_rate_set(port, baud)) {
-		/* No clock available, baudrate cannot be changed */
-		if (old)
-			baud = uart_get_baud_rate(port, old, NULL,
-						  min_baud, max_baud);
-	} else {
-		tty_termios_encode_baud_rate(termios, baud, baud);
-		uart_update_timeout(port, termios->c_cflag, baud);
-	}
+	baud = mvebu_uart_baud_rate_set(port, baud);
+
+	/* In case baudrate cannot be changed, report previous old value */
+	if (baud == 0 && old)
+		baud = tty_termios_baud_rate(old);
 
 	/* Only the following flag changes are supported */
 	if (old) {
@@ -606,6 +602,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
 		termios->c_cflag |= CS8;
 	}
 
+	if (baud != 0) {
+		tty_termios_encode_baud_rate(termios, baud, baud);
+		uart_update_timeout(port, termios->c_cflag, baud);
+	}
+
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
-- 
2.20.1


^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] serial: mvebu-uart: correctly report configured baudrate value
  2022-06-28 10:09 [PATCH] serial: mvebu-uart: correctly report configured baudrate value Pali Rohár
@ 2022-06-28 10:23 ` Ilpo Järvinen
  2022-06-30  8:35   ` Pali Rohár
  0 siblings, 1 reply; 3+ messages in thread
From: Ilpo Järvinen @ 2022-06-28 10:23 UTC (permalink / raw)
  To: Pali Rohár
  Cc: Greg Kroah-Hartman, Jiri Slaby, Allen Yan, Miquel Raynal,
	Gregory CLEMENT, linux-serial, LKML

[-- Attachment #1: Type: text/plain, Size: 3073 bytes --]

On Tue, 28 Jun 2022, Pali Rohár wrote:

> Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
> be called with the baudrate value which was set to hardware. Linux then
> report exact values via ioctl(TCGETS2) to userspace.
> 
> Change mvebu_uart_baud_rate_set() function to return baudrate value which
> was set to hardware and propagate this value to above mentioned functions.
> 
> With this change userspace would see precise value in termios c_ospeed
> field.
> 
> Signed-off-by: Pali Rohár <pali@kernel.org>
> Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")

Look better than my patch covering cases I didn't even realize
existed. Thanks.

Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

-- 
 i.


> ---
>  drivers/tty/serial/mvebu-uart.c | 25 +++++++++++++------------
>  1 file changed, 13 insertions(+), 12 deletions(-)
> 
> diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
> index 0429c2a54290..93489fe334d0 100644
> --- a/drivers/tty/serial/mvebu-uart.c
> +++ b/drivers/tty/serial/mvebu-uart.c
> @@ -470,14 +470,14 @@ static void mvebu_uart_shutdown(struct uart_port *port)
>  	}
>  }
>  
> -static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
> +static unsigned int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
>  {
>  	unsigned int d_divisor, m_divisor;
>  	unsigned long flags;
>  	u32 brdv, osamp;
>  
>  	if (!port->uartclk)
> -		return -EOPNOTSUPP;
> +		return 0;
>  
>  	/*
>  	 * The baudrate is derived from the UART clock thanks to divisors:
> @@ -548,7 +548,7 @@ static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
>  			(m_divisor << 16) | (m_divisor << 24);
>  	writel(osamp, port->membase + UART_OSAMP);
>  
> -	return 0;
> +	return DIV_ROUND_CLOSEST(port->uartclk, d_divisor * m_divisor);
>  }
>  
>  static void mvebu_uart_set_termios(struct uart_port *port,
> @@ -587,15 +587,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
>  	max_baud = port->uartclk / 80;
>  
>  	baud = uart_get_baud_rate(port, termios, old, min_baud, max_baud);
> -	if (mvebu_uart_baud_rate_set(port, baud)) {
> -		/* No clock available, baudrate cannot be changed */
> -		if (old)
> -			baud = uart_get_baud_rate(port, old, NULL,
> -						  min_baud, max_baud);
> -	} else {
> -		tty_termios_encode_baud_rate(termios, baud, baud);
> -		uart_update_timeout(port, termios->c_cflag, baud);
> -	}
> +	baud = mvebu_uart_baud_rate_set(port, baud);
> +
> +	/* In case baudrate cannot be changed, report previous old value */
> +	if (baud == 0 && old)
> +		baud = tty_termios_baud_rate(old);
>  
>  	/* Only the following flag changes are supported */
>  	if (old) {
> @@ -606,6 +602,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
>  		termios->c_cflag |= CS8;
>  	}
>  
> +	if (baud != 0) {
> +		tty_termios_encode_baud_rate(termios, baud, baud);
> +		uart_update_timeout(port, termios->c_cflag, baud);
> +	}
> +
>  	spin_unlock_irqrestore(&port->lock, flags);
>  }
>  
> 

^ permalink raw reply	[flat|nested] 3+ messages in thread

* Re: [PATCH] serial: mvebu-uart: correctly report configured baudrate value
  2022-06-28 10:23 ` Ilpo Järvinen
@ 2022-06-30  8:35   ` Pali Rohár
  0 siblings, 0 replies; 3+ messages in thread
From: Pali Rohár @ 2022-06-30  8:35 UTC (permalink / raw)
  To: Ilpo Järvinen
  Cc: Greg Kroah-Hartman, Jiri Slaby, Allen Yan, Miquel Raynal,
	Gregory CLEMENT, linux-serial, LKML

On Tuesday 28 June 2022 13:23:34 Ilpo Järvinen wrote:
> On Tue, 28 Jun 2022, Pali Rohár wrote:
> 
> > Functions tty_termios_encode_baud_rate() and uart_update_timeout() should
> > be called with the baudrate value which was set to hardware. Linux then
> > report exact values via ioctl(TCGETS2) to userspace.
> > 
> > Change mvebu_uart_baud_rate_set() function to return baudrate value which
> > was set to hardware and propagate this value to above mentioned functions.
> > 
> > With this change userspace would see precise value in termios c_ospeed
> > field.
> > 
> > Signed-off-by: Pali Rohár <pali@kernel.org>
> > Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
> 
> Look better than my patch covering cases I didn't even realize
> existed. Thanks.
> 
> Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>

Thanks for review!

Now I now why I have not sent this patch earlier. This patch hit bug
described and fixed by commit "serial: core: Fix initializing and
restoring termios speed":
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=027b57170bf8bb6999a28e4a5f3d78bf1db0f90c

Above commit is already in master since v5.16 and IIRC it was also
backported to stable trees.

So applying and testing this patch should be fine also in old trees now.

> -- 
>  i.
> 
> 
> > ---
> >  drivers/tty/serial/mvebu-uart.c | 25 +++++++++++++------------
> >  1 file changed, 13 insertions(+), 12 deletions(-)
> > 
> > diff --git a/drivers/tty/serial/mvebu-uart.c b/drivers/tty/serial/mvebu-uart.c
> > index 0429c2a54290..93489fe334d0 100644
> > --- a/drivers/tty/serial/mvebu-uart.c
> > +++ b/drivers/tty/serial/mvebu-uart.c
> > @@ -470,14 +470,14 @@ static void mvebu_uart_shutdown(struct uart_port *port)
> >  	}
> >  }
> >  
> > -static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
> > +static unsigned int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
> >  {
> >  	unsigned int d_divisor, m_divisor;
> >  	unsigned long flags;
> >  	u32 brdv, osamp;
> >  
> >  	if (!port->uartclk)
> > -		return -EOPNOTSUPP;
> > +		return 0;
> >  
> >  	/*
> >  	 * The baudrate is derived from the UART clock thanks to divisors:
> > @@ -548,7 +548,7 @@ static int mvebu_uart_baud_rate_set(struct uart_port *port, unsigned int baud)
> >  			(m_divisor << 16) | (m_divisor << 24);
> >  	writel(osamp, port->membase + UART_OSAMP);
> >  
> > -	return 0;
> > +	return DIV_ROUND_CLOSEST(port->uartclk, d_divisor * m_divisor);
> >  }
> >  
> >  static void mvebu_uart_set_termios(struct uart_port *port,
> > @@ -587,15 +587,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
> >  	max_baud = port->uartclk / 80;
> >  
> >  	baud = uart_get_baud_rate(port, termios, old, min_baud, max_baud);
> > -	if (mvebu_uart_baud_rate_set(port, baud)) {
> > -		/* No clock available, baudrate cannot be changed */
> > -		if (old)
> > -			baud = uart_get_baud_rate(port, old, NULL,
> > -						  min_baud, max_baud);
> > -	} else {
> > -		tty_termios_encode_baud_rate(termios, baud, baud);
> > -		uart_update_timeout(port, termios->c_cflag, baud);
> > -	}
> > +	baud = mvebu_uart_baud_rate_set(port, baud);
> > +
> > +	/* In case baudrate cannot be changed, report previous old value */
> > +	if (baud == 0 && old)
> > +		baud = tty_termios_baud_rate(old);
> >  
> >  	/* Only the following flag changes are supported */
> >  	if (old) {
> > @@ -606,6 +602,11 @@ static void mvebu_uart_set_termios(struct uart_port *port,
> >  		termios->c_cflag |= CS8;
> >  	}
> >  
> > +	if (baud != 0) {
> > +		tty_termios_encode_baud_rate(termios, baud, baud);
> > +		uart_update_timeout(port, termios->c_cflag, baud);
> > +	}
> > +
> >  	spin_unlock_irqrestore(&port->lock, flags);
> >  }
> >  
> > 


^ permalink raw reply	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2022-06-30  8:35 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-06-28 10:09 [PATCH] serial: mvebu-uart: correctly report configured baudrate value Pali Rohár
2022-06-28 10:23 ` Ilpo Järvinen
2022-06-30  8:35   ` Pali Rohár

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.