* [PATCH V3 0/3] drm/panel: Add NewVision NV3051D Panels
@ 2022-09-26 19:14 ` Chris Morgan
0 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, robh+dt, daniel, airlied,
sam, thierry.reding, maccraft123mc, Chris Morgan
From: Chris Morgan <macromorgan@hotmail.com>
Add the NewVision NV3051D panel as found on the Anbernic RG353P and
RG353V. The underlying LCD panel itself is unknown (the NV3051D is
the controller), so the device name is used for the panel with a
fallback to the driver IC.
Changes from V2:
- Ensured dt_binding_check and dtbs_check successfully passed.
- Corrected some minor formatting issues in documentation.
- Added another mode per userspace request for 100hz. I was unable
to find a supported 50hz mode that would also work, so for now
only 60hz, 100hz, and 120hz are supported.
Changes from V1:
- Changed compatible string to the driver IC.
- Updated documentation to use new compatible string with board
name.
- Refactored somewhat to make it easier to support other LCD panels
with this kernel module.
- Added support for 60hz mode. Adjusted pixel clock to ensure proper
60hz and 120hz (previously was running at 124hz).
- Added vendor prefix for NewVision. Anbernic vendor prefix added in
https://lore.kernel.org/linux-devicetree/20220906210324.28986-2-macroalpha82@gmail.com
Chris Morgan (3):
dt-bindings: vendor-prefixes: add NewVision vendor prefix
dt-bindings: display: panel: Add NewVision NV3051D bindings
drm/panel: Add NewVision NV3051D MIPI-DSI LCD panel
.../display/panel/newvision,nv3051d.yaml | 63 +++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-newvision-nv3051d.c | 525 ++++++++++++++++++
5 files changed, 600 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3051d.c
--
2.25.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V3 0/3] drm/panel: Add NewVision NV3051D Panels
@ 2022-09-26 19:14 ` Chris Morgan
0 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, Chris Morgan, robh+dt,
thierry.reding, sam, maccraft123mc
From: Chris Morgan <macromorgan@hotmail.com>
Add the NewVision NV3051D panel as found on the Anbernic RG353P and
RG353V. The underlying LCD panel itself is unknown (the NV3051D is
the controller), so the device name is used for the panel with a
fallback to the driver IC.
Changes from V2:
- Ensured dt_binding_check and dtbs_check successfully passed.
- Corrected some minor formatting issues in documentation.
- Added another mode per userspace request for 100hz. I was unable
to find a supported 50hz mode that would also work, so for now
only 60hz, 100hz, and 120hz are supported.
Changes from V1:
- Changed compatible string to the driver IC.
- Updated documentation to use new compatible string with board
name.
- Refactored somewhat to make it easier to support other LCD panels
with this kernel module.
- Added support for 60hz mode. Adjusted pixel clock to ensure proper
60hz and 120hz (previously was running at 124hz).
- Added vendor prefix for NewVision. Anbernic vendor prefix added in
https://lore.kernel.org/linux-devicetree/20220906210324.28986-2-macroalpha82@gmail.com
Chris Morgan (3):
dt-bindings: vendor-prefixes: add NewVision vendor prefix
dt-bindings: display: panel: Add NewVision NV3051D bindings
drm/panel: Add NewVision NV3051D MIPI-DSI LCD panel
.../display/panel/newvision,nv3051d.yaml | 63 +++
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-newvision-nv3051d.c | 525 ++++++++++++++++++
5 files changed, 600 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3051d.c
--
2.25.1
^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH V3 1/3] dt-bindings: vendor-prefixes: add NewVision vendor prefix
2022-09-26 19:14 ` Chris Morgan
@ 2022-09-26 19:14 ` Chris Morgan
-1 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, robh+dt, daniel, airlied,
sam, thierry.reding, maccraft123mc, Chris Morgan,
Krzysztof Kozlowski
From: Chris Morgan <macromorgan@hotmail.com>
NewVision (also sometimes written as New Vision) is a company based in
Shenzen that manufactures ICs for controlling LCD panels.
https://www.newvisiondisplay.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 2f0151e9f6be..d9c38e214863 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -873,6 +873,8 @@ patternProperties:
description: Shenzhen Netxeon Technology CO., LTD
"^neweast,.*":
description: Guangdong Neweast Optoelectronics CO., LTD
+ "^newvision,.*":
+ description: New Vision Display (Shenzhen) Co., Ltd.
"^nexbox,.*":
description: Nexbox
"^nextthing,.*":
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V3 1/3] dt-bindings: vendor-prefixes: add NewVision vendor prefix
@ 2022-09-26 19:14 ` Chris Morgan
0 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, Chris Morgan,
Krzysztof Kozlowski, robh+dt, thierry.reding, sam, maccraft123mc
From: Chris Morgan <macromorgan@hotmail.com>
NewVision (also sometimes written as New Vision) is a company based in
Shenzen that manufactures ICs for controlling LCD panels.
https://www.newvisiondisplay.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index 2f0151e9f6be..d9c38e214863 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -873,6 +873,8 @@ patternProperties:
description: Shenzhen Netxeon Technology CO., LTD
"^neweast,.*":
description: Guangdong Neweast Optoelectronics CO., LTD
+ "^newvision,.*":
+ description: New Vision Display (Shenzhen) Co., Ltd.
"^nexbox,.*":
description: Nexbox
"^nextthing,.*":
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V3 2/3] dt-bindings: display: panel: Add NewVision NV3051D bindings
2022-09-26 19:14 ` Chris Morgan
@ 2022-09-26 19:14 ` Chris Morgan
-1 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, robh+dt, daniel, airlied,
sam, thierry.reding, maccraft123mc, Chris Morgan
From: Chris Morgan <macromorgan@hotmail.com>
Add documentation for the NewVision NV3051D panel bindings.
Note that for the two expected consumers of this panel binding
the underlying LCD model is unknown. Name "anbernic,rg353p-panel"
is used because the hardware itself is known as "anbernic,rg353p".
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
.../display/panel/newvision,nv3051d.yaml | 63 +++++++++++++++++++
1 file changed, 63 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml b/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
new file mode 100644
index 000000000000..407de7fb5499
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/newvision,nv3051d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NewVision NV3051D based LCD panel
+
+description: |
+ The NewVision NV3051D is a driver chip used to drive DSI panels. For now,
+ this driver only supports the 640x480 panels found in the Anbernic RG353
+ based devices.
+
+maintainers:
+ - Chris Morgan <macromorgan@hotmail.com>
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - anbernic,rg353p-panel
+ - anbernic,rg353v-panel
+ - const: newvision,nv3051d
+
+ reg: true
+ backlight: true
+ port: true
+ reset-gpios: true
+ vdd-supply: true
+
+required:
+ - compatible
+ - reg
+ - backlight
+ - vdd-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "anbernic,rg353p-panel", "newvision,nv3051d";
+ reg = <0>;
+ backlight = <&backlight>;
+ reset-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&vcc3v3_lcd>;
+
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
+ };
+ };
+ };
+
+...
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V3 2/3] dt-bindings: display: panel: Add NewVision NV3051D bindings
@ 2022-09-26 19:14 ` Chris Morgan
0 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, Chris Morgan, robh+dt,
thierry.reding, sam, maccraft123mc
From: Chris Morgan <macromorgan@hotmail.com>
Add documentation for the NewVision NV3051D panel bindings.
Note that for the two expected consumers of this panel binding
the underlying LCD model is unknown. Name "anbernic,rg353p-panel"
is used because the hardware itself is known as "anbernic,rg353p".
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
.../display/panel/newvision,nv3051d.yaml | 63 +++++++++++++++++++
1 file changed, 63 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml b/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
new file mode 100644
index 000000000000..407de7fb5499
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
@@ -0,0 +1,63 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/newvision,nv3051d.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NewVision NV3051D based LCD panel
+
+description: |
+ The NewVision NV3051D is a driver chip used to drive DSI panels. For now,
+ this driver only supports the 640x480 panels found in the Anbernic RG353
+ based devices.
+
+maintainers:
+ - Chris Morgan <macromorgan@hotmail.com>
+
+allOf:
+ - $ref: panel-common.yaml#
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - anbernic,rg353p-panel
+ - anbernic,rg353v-panel
+ - const: newvision,nv3051d
+
+ reg: true
+ backlight: true
+ port: true
+ reset-gpios: true
+ vdd-supply: true
+
+required:
+ - compatible
+ - reg
+ - backlight
+ - vdd-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ dsi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ panel@0 {
+ compatible = "anbernic,rg353p-panel", "newvision,nv3051d";
+ reg = <0>;
+ backlight = <&backlight>;
+ reset-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+ vdd-supply = <&vcc3v3_lcd>;
+
+ port {
+ mipi_in_panel: endpoint {
+ remote-endpoint = <&mipi_out_panel>;
+ };
+ };
+ };
+ };
+
+...
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V3 3/3] drm/panel: Add NewVision NV3051D MIPI-DSI LCD panel
2022-09-26 19:14 ` Chris Morgan
@ 2022-09-26 19:14 ` Chris Morgan
-1 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, robh+dt, daniel, airlied,
sam, thierry.reding, maccraft123mc, Chris Morgan
From: Chris Morgan <macromorgan@hotmail.com>
Support NewVision NV3051D panels as found on the Anbernic RG353P and
RG353V. The underlying LCD part number for the RG353x devices is
unknown, so the device name and a fallback for the driver IC is
used instead.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-newvision-nv3051d.c | 525 ++++++++++++++++++
3 files changed, 535 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3051d.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index a9043eacce97..7258d28dda2f 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -296,6 +296,15 @@ config DRM_PANEL_NEC_NL8048HL11
panel (found on the Zoom2/3/3630 SDP boards). To compile this driver
as a module, choose M here.
+config DRM_PANEL_NEWVISION_NV3051D
+ tristate "NewVision NV3051D DSI panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ This driver supports the NV3051D based panel found on the Anbernic
+ RG353P and RG353V.
+
config DRM_PANEL_NEWVISION_NV3052C
tristate "NewVision NV3052C RGB/SPI panel"
depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 34e717382dbb..cb03b3a82738 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) += panel-leadtek-ltk500hd1829.o
obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o
obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
+obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3051D) += panel-newvision-nv3051d.o
obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3052C) += panel-newvision-nv3052c.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35560) += panel-novatek-nt35560.o
diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
new file mode 100644
index 000000000000..a15b6e4cb668
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NV3051D MIPI-DSI panel driver for Anbernic RG353x
+ * Copyright (C) 2022 Chris Morgan
+ *
+ * based on
+ *
+ * Elida kd35t133 3.5" MIPI-DSI panel driver
+ * Copyright (C) Theobroma Systems 2020
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/display_timing.h>
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct nv3051d_panel_info {
+ const struct drm_display_mode *display_modes;
+ unsigned int num_modes;
+ u16 width_mm, height_mm;
+ u32 bus_flags;
+};
+
+struct panel_nv3051d {
+ struct device *dev;
+ struct drm_panel panel;
+ struct gpio_desc *reset_gpio;
+ const struct nv3051d_panel_info *panel_info;
+ struct regulator *vdd;
+ bool prepared;
+};
+
+static inline struct panel_nv3051d *panel_to_panelnv3051d(struct drm_panel *panel)
+{
+ return container_of(panel, struct panel_nv3051d, panel);
+}
+
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \
+ static const u8 b[] = { cmd, seq }; \
+ int ret; \
+ ret = mipi_dsi_dcs_write_buffer(dsi, b, ARRAY_SIZE(b)); \
+ if (ret < 0) \
+ return ret; \
+ } while (0)
+
+static int panel_nv3051d_init_sequence(struct panel_nv3051d *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ /*
+ * Init sequence was supplied by device vendor with no
+ * documentation.
+ */
+
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x01);
+ dsi_dcs_write_seq(dsi, 0xE3, 0x00);
+ dsi_dcs_write_seq(dsi, 0x03, 0x40);
+ dsi_dcs_write_seq(dsi, 0x04, 0x00);
+ dsi_dcs_write_seq(dsi, 0x05, 0x03);
+ dsi_dcs_write_seq(dsi, 0x24, 0x12);
+ dsi_dcs_write_seq(dsi, 0x25, 0x1E);
+ dsi_dcs_write_seq(dsi, 0x26, 0x28);
+ dsi_dcs_write_seq(dsi, 0x27, 0x52);
+ dsi_dcs_write_seq(dsi, 0x28, 0x57);
+ dsi_dcs_write_seq(dsi, 0x29, 0x01);
+ dsi_dcs_write_seq(dsi, 0x2A, 0xDF);
+ dsi_dcs_write_seq(dsi, 0x38, 0x9C);
+ dsi_dcs_write_seq(dsi, 0x39, 0xA7);
+ dsi_dcs_write_seq(dsi, 0x3A, 0x53);
+ dsi_dcs_write_seq(dsi, 0x44, 0x00);
+ dsi_dcs_write_seq(dsi, 0x49, 0x3C);
+ dsi_dcs_write_seq(dsi, 0x59, 0xFE);
+ dsi_dcs_write_seq(dsi, 0x5C, 0x00);
+ dsi_dcs_write_seq(dsi, 0x91, 0x77);
+ dsi_dcs_write_seq(dsi, 0x92, 0x77);
+ dsi_dcs_write_seq(dsi, 0xA0, 0x55);
+ dsi_dcs_write_seq(dsi, 0xA1, 0x50);
+ dsi_dcs_write_seq(dsi, 0xA4, 0x9C);
+ dsi_dcs_write_seq(dsi, 0xA7, 0x02);
+ dsi_dcs_write_seq(dsi, 0xA8, 0x01);
+ dsi_dcs_write_seq(dsi, 0xA9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xAA, 0xFC);
+ dsi_dcs_write_seq(dsi, 0xAB, 0x28);
+ dsi_dcs_write_seq(dsi, 0xAC, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAD, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAE, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAF, 0x03);
+ dsi_dcs_write_seq(dsi, 0xB0, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x26);
+ dsi_dcs_write_seq(dsi, 0xB2, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x33);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x26);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x26);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x02);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xD1, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x29);
+ dsi_dcs_write_seq(dsi, 0xD4, 0x2B);
+ dsi_dcs_write_seq(dsi, 0xB2, 0x0C);
+ dsi_dcs_write_seq(dsi, 0xD2, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xB3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xD3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x11);
+ dsi_dcs_write_seq(dsi, 0xD6, 0x0D);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x32);
+ dsi_dcs_write_seq(dsi, 0xD7, 0x30);
+ dsi_dcs_write_seq(dsi, 0xC1, 0x04);
+ dsi_dcs_write_seq(dsi, 0xE1, 0x06);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xD8, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xB9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xD9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xBD, 0x13);
+ dsi_dcs_write_seq(dsi, 0xDD, 0x13);
+ dsi_dcs_write_seq(dsi, 0xBC, 0x11);
+ dsi_dcs_write_seq(dsi, 0xDC, 0x11);
+ dsi_dcs_write_seq(dsi, 0xBB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xBA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xBE, 0x18);
+ dsi_dcs_write_seq(dsi, 0xDE, 0x18);
+ dsi_dcs_write_seq(dsi, 0xBF, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDF, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xC0, 0x17);
+ dsi_dcs_write_seq(dsi, 0xE0, 0x17);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x3B);
+ dsi_dcs_write_seq(dsi, 0xD5, 0x3C);
+ dsi_dcs_write_seq(dsi, 0xB0, 0x0B);
+ dsi_dcs_write_seq(dsi, 0xD0, 0x0C);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x03);
+ dsi_dcs_write_seq(dsi, 0x00, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x01, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x02, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x03, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x04, 0x61);
+ dsi_dcs_write_seq(dsi, 0x05, 0x80);
+ dsi_dcs_write_seq(dsi, 0x06, 0xC7);
+ dsi_dcs_write_seq(dsi, 0x07, 0x01);
+ dsi_dcs_write_seq(dsi, 0x08, 0x82);
+ dsi_dcs_write_seq(dsi, 0x09, 0x83);
+ dsi_dcs_write_seq(dsi, 0x30, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x31, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x32, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x33, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x34, 0x61);
+ dsi_dcs_write_seq(dsi, 0x35, 0xC5);
+ dsi_dcs_write_seq(dsi, 0x36, 0x80);
+ dsi_dcs_write_seq(dsi, 0x37, 0x23);
+ dsi_dcs_write_seq(dsi, 0x40, 0x82);
+ dsi_dcs_write_seq(dsi, 0x41, 0x83);
+ dsi_dcs_write_seq(dsi, 0x42, 0x80);
+ dsi_dcs_write_seq(dsi, 0x43, 0x81);
+ dsi_dcs_write_seq(dsi, 0x44, 0x11);
+ dsi_dcs_write_seq(dsi, 0x45, 0xF2);
+ dsi_dcs_write_seq(dsi, 0x46, 0xF1);
+ dsi_dcs_write_seq(dsi, 0x47, 0x11);
+ dsi_dcs_write_seq(dsi, 0x48, 0xF4);
+ dsi_dcs_write_seq(dsi, 0x49, 0xF3);
+ dsi_dcs_write_seq(dsi, 0x50, 0x02);
+ dsi_dcs_write_seq(dsi, 0x51, 0x01);
+ dsi_dcs_write_seq(dsi, 0x52, 0x04);
+ dsi_dcs_write_seq(dsi, 0x53, 0x03);
+ dsi_dcs_write_seq(dsi, 0x54, 0x11);
+ dsi_dcs_write_seq(dsi, 0x55, 0xF6);
+ dsi_dcs_write_seq(dsi, 0x56, 0xF5);
+ dsi_dcs_write_seq(dsi, 0x57, 0x11);
+ dsi_dcs_write_seq(dsi, 0x58, 0xF8);
+ dsi_dcs_write_seq(dsi, 0x59, 0xF7);
+ dsi_dcs_write_seq(dsi, 0x7E, 0x02);
+ dsi_dcs_write_seq(dsi, 0x7F, 0x80);
+ dsi_dcs_write_seq(dsi, 0xE0, 0x5A);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x00);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x04);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x07);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x06);
+ dsi_dcs_write_seq(dsi, 0xB9, 0x05);
+ dsi_dcs_write_seq(dsi, 0xBA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xC7, 0x00);
+ dsi_dcs_write_seq(dsi, 0xCA, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xCB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xCC, 0x04);
+ dsi_dcs_write_seq(dsi, 0xCD, 0x07);
+ dsi_dcs_write_seq(dsi, 0xCE, 0x06);
+ dsi_dcs_write_seq(dsi, 0xCF, 0x05);
+ dsi_dcs_write_seq(dsi, 0xD0, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x81, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x84, 0x0E);
+ dsi_dcs_write_seq(dsi, 0x85, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x86, 0x07);
+ dsi_dcs_write_seq(dsi, 0x87, 0x04);
+ dsi_dcs_write_seq(dsi, 0x88, 0x05);
+ dsi_dcs_write_seq(dsi, 0x89, 0x06);
+ dsi_dcs_write_seq(dsi, 0x8A, 0x00);
+ dsi_dcs_write_seq(dsi, 0x97, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x9A, 0x0E);
+ dsi_dcs_write_seq(dsi, 0x9B, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x9C, 0x07);
+ dsi_dcs_write_seq(dsi, 0x9D, 0x04);
+ dsi_dcs_write_seq(dsi, 0x9E, 0x05);
+ dsi_dcs_write_seq(dsi, 0x9F, 0x06);
+ dsi_dcs_write_seq(dsi, 0xA0, 0x00);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x02);
+ dsi_dcs_write_seq(dsi, 0x01, 0x01);
+ dsi_dcs_write_seq(dsi, 0x02, 0xDA);
+ dsi_dcs_write_seq(dsi, 0x03, 0xBA);
+ dsi_dcs_write_seq(dsi, 0x04, 0xA8);
+ dsi_dcs_write_seq(dsi, 0x05, 0x9A);
+ dsi_dcs_write_seq(dsi, 0x06, 0x70);
+ dsi_dcs_write_seq(dsi, 0x07, 0xFF);
+ dsi_dcs_write_seq(dsi, 0x08, 0x91);
+ dsi_dcs_write_seq(dsi, 0x09, 0x90);
+ dsi_dcs_write_seq(dsi, 0x0A, 0xFF);
+ dsi_dcs_write_seq(dsi, 0x0B, 0x8F);
+ dsi_dcs_write_seq(dsi, 0x0C, 0x60);
+ dsi_dcs_write_seq(dsi, 0x0D, 0x58);
+ dsi_dcs_write_seq(dsi, 0x0E, 0x48);
+ dsi_dcs_write_seq(dsi, 0x0F, 0x38);
+ dsi_dcs_write_seq(dsi, 0x10, 0x2B);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x00);
+ dsi_dcs_write_seq(dsi, 0x36, 0x02);
+ dsi_dcs_write_seq(dsi, 0x3A, 0x70);
+
+ dev_dbg(ctx->dev, "Panel init sequence done\n");
+
+ return 0;
+}
+
+static int panel_nv3051d_unprepare(struct drm_panel *panel)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (!ctx->prepared)
+ return 0;
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret < 0)
+ dev_err(ctx->dev, "failed to set display off: %d\n", ret);
+
+ msleep(20);
+
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret);
+ return ret;
+ }
+
+ usleep_range(10000, 15000);
+
+ regulator_disable(ctx->vdd);
+
+ ctx->prepared = false;
+
+ return 0;
+}
+
+static int panel_nv3051d_prepare(struct drm_panel *panel)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (ctx->prepared)
+ return 0;
+
+ dev_dbg(ctx->dev, "Resetting the panel\n");
+ ret = regulator_enable(ctx->vdd);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable vdd supply: %d\n", ret);
+ return ret;
+ }
+
+ usleep_range(2000, 3000);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+ msleep(150);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+ msleep(20);
+
+ ret = panel_nv3051d_init_sequence(ctx);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to exit sleep mode: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ msleep(200);
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to set display on: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ usleep_range(10000, 15000);
+
+ ctx->prepared = true;
+
+ return 0;
+
+disable_vdd:
+ regulator_disable(ctx->vdd);
+ return ret;
+}
+
+static int panel_nv3051d_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ const struct nv3051d_panel_info *panel_info = ctx->panel_info;
+ struct drm_display_mode *mode;
+ unsigned int i;
+
+ for (i = 0; i < panel_info->num_modes; i++) {
+ mode = drm_mode_duplicate(connector->dev,
+ &panel_info->display_modes[i]);
+ if (!mode)
+ return -ENOMEM;
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER;
+ if (panel_info->num_modes == 1)
+ mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+ drm_mode_probed_add(connector, mode);
+ }
+
+ connector->display_info.bpc = 8;
+ connector->display_info.width_mm = panel_info->width_mm;
+ connector->display_info.height_mm = panel_info->height_mm;
+ connector->display_info.bus_flags = panel_info->bus_flags;
+
+ return panel_info->num_modes;
+}
+
+static const struct drm_panel_funcs panel_nv3051d_funcs = {
+ .unprepare = panel_nv3051d_unprepare,
+ .prepare = panel_nv3051d_prepare,
+ .get_modes = panel_nv3051d_get_modes,
+};
+
+static int panel_nv3051d_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct panel_nv3051d *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->dev = dev;
+
+ ctx->panel_info = of_device_get_match_data(dev);
+ if (!ctx->panel_info)
+ return -EINVAL;
+
+ ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio)) {
+ dev_err(dev, "cannot get reset gpio\n");
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ ctx->vdd = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(ctx->vdd)) {
+ ret = PTR_ERR(ctx->vdd);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vdd regulator: %d\n", ret);
+ return ret;
+ }
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
+
+ drm_panel_init(&ctx->panel, &dsi->dev, &panel_nv3051d_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return ret;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err(dev, "mipi_dsi_attach failed: %d\n", ret);
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void panel_nv3051d_shutdown(struct mipi_dsi_device *dsi)
+{
+ struct panel_nv3051d *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ ret = drm_panel_unprepare(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret);
+
+ ret = drm_panel_disable(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret);
+}
+
+static int panel_nv3051d_remove(struct mipi_dsi_device *dsi)
+{
+ struct panel_nv3051d *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ panel_nv3051d_shutdown(dsi);
+
+ ret = mipi_dsi_detach(dsi);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+ drm_panel_remove(&ctx->panel);
+
+ return 0;
+}
+
+static const struct drm_display_mode nv3051d_rgxx3_modes[] = {
+ { /* 120hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 48300,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+ { /* 100hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 40250,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+ { /* 60hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 24150,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+};
+
+static const struct nv3051d_panel_info nv3051d_rgxx3_info = {
+ .display_modes = nv3051d_rgxx3_modes,
+ .num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
+ .width_mm = 70,
+ .height_mm = 57,
+ .bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+};
+
+static const struct of_device_id newvision_nv3051d_of_match[] = {
+ { .compatible = "newvision,nv3051d", .data = &nv3051d_rgxx3_info },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, newvision_nv3051d_of_match);
+
+static struct mipi_dsi_driver newvision_nv3051d_driver = {
+ .driver = {
+ .name = "panel-newvision-nv3051d",
+ .of_match_table = newvision_nv3051d_of_match,
+ },
+ .probe = panel_nv3051d_probe,
+ .remove = panel_nv3051d_remove,
+ .shutdown = panel_nv3051d_shutdown,
+};
+module_mipi_dsi_driver(newvision_nv3051d_driver);
+
+MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>");
+MODULE_DESCRIPTION("DRM driver for Newvision NV3051D based MIPI DSI panels");
+MODULE_LICENSE("GPL");
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH V3 3/3] drm/panel: Add NewVision NV3051D MIPI-DSI LCD panel
@ 2022-09-26 19:14 ` Chris Morgan
0 siblings, 0 replies; 10+ messages in thread
From: Chris Morgan @ 2022-09-26 19:14 UTC (permalink / raw)
To: dri-devel
Cc: devicetree, krzysztof.kozlowski+dt, Chris Morgan, robh+dt,
thierry.reding, sam, maccraft123mc
From: Chris Morgan <macromorgan@hotmail.com>
Support NewVision NV3051D panels as found on the Anbernic RG353P and
RG353V. The underlying LCD part number for the RG353x devices is
unknown, so the device name and a fallback for the driver IC is
used instead.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
---
drivers/gpu/drm/panel/Kconfig | 9 +
drivers/gpu/drm/panel/Makefile | 1 +
.../gpu/drm/panel/panel-newvision-nv3051d.c | 525 ++++++++++++++++++
3 files changed, 535 insertions(+)
create mode 100644 drivers/gpu/drm/panel/panel-newvision-nv3051d.c
diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
index a9043eacce97..7258d28dda2f 100644
--- a/drivers/gpu/drm/panel/Kconfig
+++ b/drivers/gpu/drm/panel/Kconfig
@@ -296,6 +296,15 @@ config DRM_PANEL_NEC_NL8048HL11
panel (found on the Zoom2/3/3630 SDP boards). To compile this driver
as a module, choose M here.
+config DRM_PANEL_NEWVISION_NV3051D
+ tristate "NewVision NV3051D DSI panel"
+ depends on OF
+ depends on DRM_MIPI_DSI
+ depends on BACKLIGHT_CLASS_DEVICE
+ help
+ This driver supports the NV3051D based panel found on the Anbernic
+ RG353P and RG353V.
+
config DRM_PANEL_NEWVISION_NV3052C
tristate "NewVision NV3052C RGB/SPI panel"
depends on OF && SPI
diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
index 34e717382dbb..cb03b3a82738 100644
--- a/drivers/gpu/drm/panel/Makefile
+++ b/drivers/gpu/drm/panel/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_DRM_PANEL_LEADTEK_LTK500HD1829) += panel-leadtek-ltk500hd1829.o
obj-$(CONFIG_DRM_PANEL_LG_LB035Q02) += panel-lg-lb035q02.o
obj-$(CONFIG_DRM_PANEL_LG_LG4573) += panel-lg-lg4573.o
obj-$(CONFIG_DRM_PANEL_NEC_NL8048HL11) += panel-nec-nl8048hl11.o
+obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3051D) += panel-newvision-nv3051d.o
obj-$(CONFIG_DRM_PANEL_NEWVISION_NV3052C) += panel-newvision-nv3052c.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35510) += panel-novatek-nt35510.o
obj-$(CONFIG_DRM_PANEL_NOVATEK_NT35560) += panel-novatek-nt35560.o
diff --git a/drivers/gpu/drm/panel/panel-newvision-nv3051d.c b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
new file mode 100644
index 000000000000..a15b6e4cb668
--- /dev/null
+++ b/drivers/gpu/drm/panel/panel-newvision-nv3051d.c
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * NV3051D MIPI-DSI panel driver for Anbernic RG353x
+ * Copyright (C) 2022 Chris Morgan
+ *
+ * based on
+ *
+ * Elida kd35t133 3.5" MIPI-DSI panel driver
+ * Copyright (C) Theobroma Systems 2020
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/media-bus-format.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/display_timing.h>
+#include <video/mipi_display.h>
+
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_modes.h>
+#include <drm/drm_panel.h>
+
+struct nv3051d_panel_info {
+ const struct drm_display_mode *display_modes;
+ unsigned int num_modes;
+ u16 width_mm, height_mm;
+ u32 bus_flags;
+};
+
+struct panel_nv3051d {
+ struct device *dev;
+ struct drm_panel panel;
+ struct gpio_desc *reset_gpio;
+ const struct nv3051d_panel_info *panel_info;
+ struct regulator *vdd;
+ bool prepared;
+};
+
+static inline struct panel_nv3051d *panel_to_panelnv3051d(struct drm_panel *panel)
+{
+ return container_of(panel, struct panel_nv3051d, panel);
+}
+
+#define dsi_dcs_write_seq(dsi, cmd, seq...) do { \
+ static const u8 b[] = { cmd, seq }; \
+ int ret; \
+ ret = mipi_dsi_dcs_write_buffer(dsi, b, ARRAY_SIZE(b)); \
+ if (ret < 0) \
+ return ret; \
+ } while (0)
+
+static int panel_nv3051d_init_sequence(struct panel_nv3051d *ctx)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+
+ /*
+ * Init sequence was supplied by device vendor with no
+ * documentation.
+ */
+
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x01);
+ dsi_dcs_write_seq(dsi, 0xE3, 0x00);
+ dsi_dcs_write_seq(dsi, 0x03, 0x40);
+ dsi_dcs_write_seq(dsi, 0x04, 0x00);
+ dsi_dcs_write_seq(dsi, 0x05, 0x03);
+ dsi_dcs_write_seq(dsi, 0x24, 0x12);
+ dsi_dcs_write_seq(dsi, 0x25, 0x1E);
+ dsi_dcs_write_seq(dsi, 0x26, 0x28);
+ dsi_dcs_write_seq(dsi, 0x27, 0x52);
+ dsi_dcs_write_seq(dsi, 0x28, 0x57);
+ dsi_dcs_write_seq(dsi, 0x29, 0x01);
+ dsi_dcs_write_seq(dsi, 0x2A, 0xDF);
+ dsi_dcs_write_seq(dsi, 0x38, 0x9C);
+ dsi_dcs_write_seq(dsi, 0x39, 0xA7);
+ dsi_dcs_write_seq(dsi, 0x3A, 0x53);
+ dsi_dcs_write_seq(dsi, 0x44, 0x00);
+ dsi_dcs_write_seq(dsi, 0x49, 0x3C);
+ dsi_dcs_write_seq(dsi, 0x59, 0xFE);
+ dsi_dcs_write_seq(dsi, 0x5C, 0x00);
+ dsi_dcs_write_seq(dsi, 0x91, 0x77);
+ dsi_dcs_write_seq(dsi, 0x92, 0x77);
+ dsi_dcs_write_seq(dsi, 0xA0, 0x55);
+ dsi_dcs_write_seq(dsi, 0xA1, 0x50);
+ dsi_dcs_write_seq(dsi, 0xA4, 0x9C);
+ dsi_dcs_write_seq(dsi, 0xA7, 0x02);
+ dsi_dcs_write_seq(dsi, 0xA8, 0x01);
+ dsi_dcs_write_seq(dsi, 0xA9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xAA, 0xFC);
+ dsi_dcs_write_seq(dsi, 0xAB, 0x28);
+ dsi_dcs_write_seq(dsi, 0xAC, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAD, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAE, 0x06);
+ dsi_dcs_write_seq(dsi, 0xAF, 0x03);
+ dsi_dcs_write_seq(dsi, 0xB0, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x26);
+ dsi_dcs_write_seq(dsi, 0xB2, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x33);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x26);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x08);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x26);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x02);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xD1, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x29);
+ dsi_dcs_write_seq(dsi, 0xD4, 0x2B);
+ dsi_dcs_write_seq(dsi, 0xB2, 0x0C);
+ dsi_dcs_write_seq(dsi, 0xD2, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xB3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xD3, 0x28);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x11);
+ dsi_dcs_write_seq(dsi, 0xD6, 0x0D);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x32);
+ dsi_dcs_write_seq(dsi, 0xD7, 0x30);
+ dsi_dcs_write_seq(dsi, 0xC1, 0x04);
+ dsi_dcs_write_seq(dsi, 0xE1, 0x06);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xD8, 0x0A);
+ dsi_dcs_write_seq(dsi, 0xB9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xD9, 0x01);
+ dsi_dcs_write_seq(dsi, 0xBD, 0x13);
+ dsi_dcs_write_seq(dsi, 0xDD, 0x13);
+ dsi_dcs_write_seq(dsi, 0xBC, 0x11);
+ dsi_dcs_write_seq(dsi, 0xDC, 0x11);
+ dsi_dcs_write_seq(dsi, 0xBB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xBA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xBE, 0x18);
+ dsi_dcs_write_seq(dsi, 0xDE, 0x18);
+ dsi_dcs_write_seq(dsi, 0xBF, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xDF, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xC0, 0x17);
+ dsi_dcs_write_seq(dsi, 0xE0, 0x17);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x3B);
+ dsi_dcs_write_seq(dsi, 0xD5, 0x3C);
+ dsi_dcs_write_seq(dsi, 0xB0, 0x0B);
+ dsi_dcs_write_seq(dsi, 0xD0, 0x0C);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x03);
+ dsi_dcs_write_seq(dsi, 0x00, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x01, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x02, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x03, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x04, 0x61);
+ dsi_dcs_write_seq(dsi, 0x05, 0x80);
+ dsi_dcs_write_seq(dsi, 0x06, 0xC7);
+ dsi_dcs_write_seq(dsi, 0x07, 0x01);
+ dsi_dcs_write_seq(dsi, 0x08, 0x82);
+ dsi_dcs_write_seq(dsi, 0x09, 0x83);
+ dsi_dcs_write_seq(dsi, 0x30, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x31, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x32, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x33, 0x2A);
+ dsi_dcs_write_seq(dsi, 0x34, 0x61);
+ dsi_dcs_write_seq(dsi, 0x35, 0xC5);
+ dsi_dcs_write_seq(dsi, 0x36, 0x80);
+ dsi_dcs_write_seq(dsi, 0x37, 0x23);
+ dsi_dcs_write_seq(dsi, 0x40, 0x82);
+ dsi_dcs_write_seq(dsi, 0x41, 0x83);
+ dsi_dcs_write_seq(dsi, 0x42, 0x80);
+ dsi_dcs_write_seq(dsi, 0x43, 0x81);
+ dsi_dcs_write_seq(dsi, 0x44, 0x11);
+ dsi_dcs_write_seq(dsi, 0x45, 0xF2);
+ dsi_dcs_write_seq(dsi, 0x46, 0xF1);
+ dsi_dcs_write_seq(dsi, 0x47, 0x11);
+ dsi_dcs_write_seq(dsi, 0x48, 0xF4);
+ dsi_dcs_write_seq(dsi, 0x49, 0xF3);
+ dsi_dcs_write_seq(dsi, 0x50, 0x02);
+ dsi_dcs_write_seq(dsi, 0x51, 0x01);
+ dsi_dcs_write_seq(dsi, 0x52, 0x04);
+ dsi_dcs_write_seq(dsi, 0x53, 0x03);
+ dsi_dcs_write_seq(dsi, 0x54, 0x11);
+ dsi_dcs_write_seq(dsi, 0x55, 0xF6);
+ dsi_dcs_write_seq(dsi, 0x56, 0xF5);
+ dsi_dcs_write_seq(dsi, 0x57, 0x11);
+ dsi_dcs_write_seq(dsi, 0x58, 0xF8);
+ dsi_dcs_write_seq(dsi, 0x59, 0xF7);
+ dsi_dcs_write_seq(dsi, 0x7E, 0x02);
+ dsi_dcs_write_seq(dsi, 0x7F, 0x80);
+ dsi_dcs_write_seq(dsi, 0xE0, 0x5A);
+ dsi_dcs_write_seq(dsi, 0xB1, 0x00);
+ dsi_dcs_write_seq(dsi, 0xB4, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xB5, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xB6, 0x04);
+ dsi_dcs_write_seq(dsi, 0xB7, 0x07);
+ dsi_dcs_write_seq(dsi, 0xB8, 0x06);
+ dsi_dcs_write_seq(dsi, 0xB9, 0x05);
+ dsi_dcs_write_seq(dsi, 0xBA, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xC7, 0x00);
+ dsi_dcs_write_seq(dsi, 0xCA, 0x0E);
+ dsi_dcs_write_seq(dsi, 0xCB, 0x0F);
+ dsi_dcs_write_seq(dsi, 0xCC, 0x04);
+ dsi_dcs_write_seq(dsi, 0xCD, 0x07);
+ dsi_dcs_write_seq(dsi, 0xCE, 0x06);
+ dsi_dcs_write_seq(dsi, 0xCF, 0x05);
+ dsi_dcs_write_seq(dsi, 0xD0, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x81, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x84, 0x0E);
+ dsi_dcs_write_seq(dsi, 0x85, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x86, 0x07);
+ dsi_dcs_write_seq(dsi, 0x87, 0x04);
+ dsi_dcs_write_seq(dsi, 0x88, 0x05);
+ dsi_dcs_write_seq(dsi, 0x89, 0x06);
+ dsi_dcs_write_seq(dsi, 0x8A, 0x00);
+ dsi_dcs_write_seq(dsi, 0x97, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x9A, 0x0E);
+ dsi_dcs_write_seq(dsi, 0x9B, 0x0F);
+ dsi_dcs_write_seq(dsi, 0x9C, 0x07);
+ dsi_dcs_write_seq(dsi, 0x9D, 0x04);
+ dsi_dcs_write_seq(dsi, 0x9E, 0x05);
+ dsi_dcs_write_seq(dsi, 0x9F, 0x06);
+ dsi_dcs_write_seq(dsi, 0xA0, 0x00);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x02);
+ dsi_dcs_write_seq(dsi, 0x01, 0x01);
+ dsi_dcs_write_seq(dsi, 0x02, 0xDA);
+ dsi_dcs_write_seq(dsi, 0x03, 0xBA);
+ dsi_dcs_write_seq(dsi, 0x04, 0xA8);
+ dsi_dcs_write_seq(dsi, 0x05, 0x9A);
+ dsi_dcs_write_seq(dsi, 0x06, 0x70);
+ dsi_dcs_write_seq(dsi, 0x07, 0xFF);
+ dsi_dcs_write_seq(dsi, 0x08, 0x91);
+ dsi_dcs_write_seq(dsi, 0x09, 0x90);
+ dsi_dcs_write_seq(dsi, 0x0A, 0xFF);
+ dsi_dcs_write_seq(dsi, 0x0B, 0x8F);
+ dsi_dcs_write_seq(dsi, 0x0C, 0x60);
+ dsi_dcs_write_seq(dsi, 0x0D, 0x58);
+ dsi_dcs_write_seq(dsi, 0x0E, 0x48);
+ dsi_dcs_write_seq(dsi, 0x0F, 0x38);
+ dsi_dcs_write_seq(dsi, 0x10, 0x2B);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x30);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x52);
+ dsi_dcs_write_seq(dsi, 0xFF, 0x00);
+ dsi_dcs_write_seq(dsi, 0x36, 0x02);
+ dsi_dcs_write_seq(dsi, 0x3A, 0x70);
+
+ dev_dbg(ctx->dev, "Panel init sequence done\n");
+
+ return 0;
+}
+
+static int panel_nv3051d_unprepare(struct drm_panel *panel)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (!ctx->prepared)
+ return 0;
+
+ ret = mipi_dsi_dcs_set_display_off(dsi);
+ if (ret < 0)
+ dev_err(ctx->dev, "failed to set display off: %d\n", ret);
+
+ msleep(20);
+
+ ret = mipi_dsi_dcs_enter_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret);
+ return ret;
+ }
+
+ usleep_range(10000, 15000);
+
+ regulator_disable(ctx->vdd);
+
+ ctx->prepared = false;
+
+ return 0;
+}
+
+static int panel_nv3051d_prepare(struct drm_panel *panel)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ int ret;
+
+ if (ctx->prepared)
+ return 0;
+
+ dev_dbg(ctx->dev, "Resetting the panel\n");
+ ret = regulator_enable(ctx->vdd);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to enable vdd supply: %d\n", ret);
+ return ret;
+ }
+
+ usleep_range(2000, 3000);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 1);
+ msleep(150);
+ gpiod_set_value_cansleep(ctx->reset_gpio, 0);
+ msleep(20);
+
+ ret = panel_nv3051d_init_sequence(ctx);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to exit sleep mode: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ msleep(200);
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret < 0) {
+ dev_err(ctx->dev, "Failed to set display on: %d\n", ret);
+ goto disable_vdd;
+ }
+
+ usleep_range(10000, 15000);
+
+ ctx->prepared = true;
+
+ return 0;
+
+disable_vdd:
+ regulator_disable(ctx->vdd);
+ return ret;
+}
+
+static int panel_nv3051d_get_modes(struct drm_panel *panel,
+ struct drm_connector *connector)
+{
+ struct panel_nv3051d *ctx = panel_to_panelnv3051d(panel);
+ const struct nv3051d_panel_info *panel_info = ctx->panel_info;
+ struct drm_display_mode *mode;
+ unsigned int i;
+
+ for (i = 0; i < panel_info->num_modes; i++) {
+ mode = drm_mode_duplicate(connector->dev,
+ &panel_info->display_modes[i]);
+ if (!mode)
+ return -ENOMEM;
+
+ drm_mode_set_name(mode);
+
+ mode->type = DRM_MODE_TYPE_DRIVER;
+ if (panel_info->num_modes == 1)
+ mode->type |= DRM_MODE_TYPE_PREFERRED;
+
+ drm_mode_probed_add(connector, mode);
+ }
+
+ connector->display_info.bpc = 8;
+ connector->display_info.width_mm = panel_info->width_mm;
+ connector->display_info.height_mm = panel_info->height_mm;
+ connector->display_info.bus_flags = panel_info->bus_flags;
+
+ return panel_info->num_modes;
+}
+
+static const struct drm_panel_funcs panel_nv3051d_funcs = {
+ .unprepare = panel_nv3051d_unprepare,
+ .prepare = panel_nv3051d_prepare,
+ .get_modes = panel_nv3051d_get_modes,
+};
+
+static int panel_nv3051d_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct panel_nv3051d *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ ctx->dev = dev;
+
+ ctx->panel_info = of_device_get_match_data(dev);
+ if (!ctx->panel_info)
+ return -EINVAL;
+
+ ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(ctx->reset_gpio)) {
+ dev_err(dev, "cannot get reset gpio\n");
+ return PTR_ERR(ctx->reset_gpio);
+ }
+
+ ctx->vdd = devm_regulator_get(dev, "vdd");
+ if (IS_ERR(ctx->vdd)) {
+ ret = PTR_ERR(ctx->vdd);
+ if (ret != -EPROBE_DEFER)
+ dev_err(dev, "Failed to request vdd regulator: %d\n", ret);
+ return ret;
+ }
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
+
+ drm_panel_init(&ctx->panel, &dsi->dev, &panel_nv3051d_funcs,
+ DRM_MODE_CONNECTOR_DSI);
+
+ ret = drm_panel_of_backlight(&ctx->panel);
+ if (ret)
+ return ret;
+
+ drm_panel_add(&ctx->panel);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err(dev, "mipi_dsi_attach failed: %d\n", ret);
+ drm_panel_remove(&ctx->panel);
+ return ret;
+ }
+
+ return 0;
+}
+
+static void panel_nv3051d_shutdown(struct mipi_dsi_device *dsi)
+{
+ struct panel_nv3051d *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ ret = drm_panel_unprepare(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret);
+
+ ret = drm_panel_disable(&ctx->panel);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret);
+}
+
+static int panel_nv3051d_remove(struct mipi_dsi_device *dsi)
+{
+ struct panel_nv3051d *ctx = mipi_dsi_get_drvdata(dsi);
+ int ret;
+
+ panel_nv3051d_shutdown(dsi);
+
+ ret = mipi_dsi_detach(dsi);
+ if (ret < 0)
+ dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret);
+
+ drm_panel_remove(&ctx->panel);
+
+ return 0;
+}
+
+static const struct drm_display_mode nv3051d_rgxx3_modes[] = {
+ { /* 120hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 48300,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+ { /* 100hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 40250,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+ { /* 60hz */
+ .hdisplay = 640,
+ .hsync_start = 640 + 40,
+ .hsync_end = 640 + 40 + 2,
+ .htotal = 640 + 40 + 2 + 80,
+ .vdisplay = 480,
+ .vsync_start = 480 + 18,
+ .vsync_end = 480 + 18 + 2,
+ .vtotal = 480 + 18 + 2 + 28,
+ .clock = 24150,
+ .flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
+ },
+};
+
+static const struct nv3051d_panel_info nv3051d_rgxx3_info = {
+ .display_modes = nv3051d_rgxx3_modes,
+ .num_modes = ARRAY_SIZE(nv3051d_rgxx3_modes),
+ .width_mm = 70,
+ .height_mm = 57,
+ .bus_flags = DRM_BUS_FLAG_DE_LOW | DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE,
+};
+
+static const struct of_device_id newvision_nv3051d_of_match[] = {
+ { .compatible = "newvision,nv3051d", .data = &nv3051d_rgxx3_info },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, newvision_nv3051d_of_match);
+
+static struct mipi_dsi_driver newvision_nv3051d_driver = {
+ .driver = {
+ .name = "panel-newvision-nv3051d",
+ .of_match_table = newvision_nv3051d_of_match,
+ },
+ .probe = panel_nv3051d_probe,
+ .remove = panel_nv3051d_remove,
+ .shutdown = panel_nv3051d_shutdown,
+};
+module_mipi_dsi_driver(newvision_nv3051d_driver);
+
+MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>");
+MODULE_DESCRIPTION("DRM driver for Newvision NV3051D based MIPI DSI panels");
+MODULE_LICENSE("GPL");
--
2.25.1
^ permalink raw reply related [flat|nested] 10+ messages in thread
* Re: [PATCH V3 2/3] dt-bindings: display: panel: Add NewVision NV3051D bindings
2022-09-26 19:14 ` Chris Morgan
@ 2022-09-29 21:54 ` Rob Herring
-1 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2022-09-29 21:54 UTC (permalink / raw)
To: Chris Morgan
Cc: devicetree, daniel, krzysztof.kozlowski+dt, Chris Morgan,
airlied, sam, maccraft123mc, dri-devel, robh+dt, thierry.reding
On Mon, 26 Sep 2022 14:14:27 -0500, Chris Morgan wrote:
> From: Chris Morgan <macromorgan@hotmail.com>
>
> Add documentation for the NewVision NV3051D panel bindings.
> Note that for the two expected consumers of this panel binding
> the underlying LCD model is unknown. Name "anbernic,rg353p-panel"
> is used because the hardware itself is known as "anbernic,rg353p".
>
> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> ---
> .../display/panel/newvision,nv3051d.yaml | 63 +++++++++++++++++++
> 1 file changed, 63 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 10+ messages in thread
* Re: [PATCH V3 2/3] dt-bindings: display: panel: Add NewVision NV3051D bindings
@ 2022-09-29 21:54 ` Rob Herring
0 siblings, 0 replies; 10+ messages in thread
From: Rob Herring @ 2022-09-29 21:54 UTC (permalink / raw)
To: Chris Morgan
Cc: devicetree, krzysztof.kozlowski+dt, dri-devel, robh+dt,
thierry.reding, Chris Morgan, sam, maccraft123mc
On Mon, 26 Sep 2022 14:14:27 -0500, Chris Morgan wrote:
> From: Chris Morgan <macromorgan@hotmail.com>
>
> Add documentation for the NewVision NV3051D panel bindings.
> Note that for the two expected consumers of this panel binding
> the underlying LCD model is unknown. Name "anbernic,rg353p-panel"
> is used because the hardware itself is known as "anbernic,rg353p".
>
> Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
> ---
> .../display/panel/newvision,nv3051d.yaml | 63 +++++++++++++++++++
> 1 file changed, 63 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/newvision,nv3051d.yaml
>
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2022-09-29 21:55 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-26 19:14 [PATCH V3 0/3] drm/panel: Add NewVision NV3051D Panels Chris Morgan
2022-09-26 19:14 ` Chris Morgan
2022-09-26 19:14 ` [PATCH V3 1/3] dt-bindings: vendor-prefixes: add NewVision vendor prefix Chris Morgan
2022-09-26 19:14 ` Chris Morgan
2022-09-26 19:14 ` [PATCH V3 2/3] dt-bindings: display: panel: Add NewVision NV3051D bindings Chris Morgan
2022-09-26 19:14 ` Chris Morgan
2022-09-29 21:54 ` Rob Herring
2022-09-29 21:54 ` Rob Herring
2022-09-26 19:14 ` [PATCH V3 3/3] drm/panel: Add NewVision NV3051D MIPI-DSI LCD panel Chris Morgan
2022-09-26 19:14 ` Chris Morgan
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.