[PATCH AUTOSEL 4.19 01/11] ARM: dts: imx7d-sdb: config the max pressure for tsc2046

[PATCH AUTOSEL 4.19 01/11] ARM: dts: imx7d-sdb: config the max pressure for tsc2046

[Sasha Levin]

From: Haibo Chen <haibo.chen@nxp.com>

[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]

Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,

[17:19:39.183] event1  - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1  - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1  - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1  - not using input device '/dev/input/event1'

This will then cause the APP weston-touch-calibrator can't list touch devices.

root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.

And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 317f1bcc56e2..bd2c3c8f4ebb 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -163,12 +163,7 @@ tsc2046@0 {
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
 		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
-- 
2.35.1

[PATCH AUTOSEL 4.19 01/11] ARM: dts: imx7d-sdb: config the max pressure for tsc2046

[Sasha Levin]

From: Haibo Chen <haibo.chen@nxp.com>

[ Upstream commit e7c4ebe2f9cd68588eb24ba4ed122e696e2d5272 ]

Use the general touchscreen method to config the max pressure for
touch tsc2046(data sheet suggest 8 bit pressure), otherwise, for
ABS_PRESSURE, when config the same max and min value, weston will
meet the following issue,

[17:19:39.183] event1  - ADS7846 Touchscreen: is tagged by udev as: Touchscreen
[17:19:39.183] event1  - ADS7846 Touchscreen: kernel bug: device has min == max on ABS_PRESSURE
[17:19:39.183] event1  - ADS7846 Touchscreen: was rejected
[17:19:39.183] event1  - not using input device '/dev/input/event1'

This will then cause the APP weston-touch-calibrator can't list touch devices.

root@imx6ul7d:~# weston-touch-calibrator
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
No devices listed.

And accroding to binding Doc, "ti,x-max", "ti,y-max", "ti,pressure-max"
belong to the deprecated properties, so remove them. Also for "ti,x-min",
"ti,y-min", "ti,x-plate-ohms", the value set in dts equal to the default
value in driver, so are redundant, also remove here.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx7d-sdb.dts | 7 +------
 1 file changed, 1 insertion(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 317f1bcc56e2..bd2c3c8f4ebb 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -163,12 +163,7 @@ tsc2046@0 {
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
 		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 02/11] soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF

[Sasha Levin]

From: Jean Delvare <jdelvare@suse.de>

[ Upstream commit 2778caedb5667239823a29148dfc48b26a8b3c2a ]

With the following configuration options:
CONFIG_OF is not set
CONFIG_MTK_PMIC_WRAP=y
CONFIG_MTK_SCPSYS=y
we get the following build warnings:

  CC      drivers/soc/mediatek/mtk-pmic-wrap.o
drivers/soc/mediatek/mtk-pmic-wrap.c:2138:34: warning: ‘of_pwrap_match_tbl’ defined but not used [-Wunused-const-variable=]
drivers/soc/mediatek/mtk-pmic-wrap.c:1953:34: warning: ‘of_slave_match_tbl’ defined but not used [-Wunused-const-variable=]
  CC      drivers/soc/mediatek/mtk-scpsys.o
drivers/soc/mediatek/mtk-scpsys.c:1084:34: warning: ‘of_scpsys_match_tbl’ defined but not used [-Wunused-const-variable=]

Looking at the code, both drivers can only bind to OF-defined device
nodes, so these drivers are useless without OF and should therefore
depend on it.

Also drop of_match_ptr() from both drivers. We already know what it
will resolve to, so we might as well save cpp some work.

Developers or QA teams who wish to test-build the code can still do
so by enabling CONFIG_OF, which is available on all architectures and
has no dependencies.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202207240252.ZY5hSCNB-lkp@intel.com/
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chenglin Xu <chenglin.xu@mediatek.com>
Link: https://lore.kernel.org/r/20220730144833.0a0d9825@endymion.delvare
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/mediatek/Kconfig         | 2 ++
 drivers/soc/mediatek/mtk-pmic-wrap.c | 2 +-
 drivers/soc/mediatek/mtk-scpsys.c    | 2 +-
 3 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
index a7d0667338f2..2bb92efd01a8 100644
--- a/drivers/soc/mediatek/Kconfig
+++ b/drivers/soc/mediatek/Kconfig
@@ -15,6 +15,7 @@ config MTK_INFRACFG
 config MTK_PMIC_WRAP
 	tristate "MediaTek PMIC Wrapper Support"
 	depends on RESET_CONTROLLER
+	depends on OF
 	select REGMAP
 	help
 	  Say yes here to add support for MediaTek PMIC Wrapper found
@@ -24,6 +25,7 @@ config MTK_PMIC_WRAP
 config MTK_SCPSYS
 	bool "MediaTek SCPSYS Support"
 	default ARCH_MEDIATEK
+	depends on OF
 	select REGMAP
 	select MTK_INFRACFG
 	select PM_GENERIC_DOMAINS if PM
diff --git a/drivers/soc/mediatek/mtk-pmic-wrap.c b/drivers/soc/mediatek/mtk-pmic-wrap.c
index 011a40b5fb49..0e7dc2f01296 100644
--- a/drivers/soc/mediatek/mtk-pmic-wrap.c
+++ b/drivers/soc/mediatek/mtk-pmic-wrap.c
@@ -1672,7 +1672,7 @@ static int pwrap_probe(struct platform_device *pdev)
 static struct platform_driver pwrap_drv = {
 	.driver = {
 		.name = "mt-pmic-pwrap",
-		.of_match_table = of_match_ptr(of_pwrap_match_tbl),
+		.of_match_table = of_pwrap_match_tbl,
 	},
 	.probe = pwrap_probe,
 };
diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
index ef54f1638d20..06543e41d015 100644
--- a/drivers/soc/mediatek/mtk-scpsys.c
+++ b/drivers/soc/mediatek/mtk-scpsys.c
@@ -1071,7 +1071,7 @@ static struct platform_driver scpsys_drv = {
 		.name = "mtk-scpsys",
 		.suppress_bind_attrs = true,
 		.owner = THIS_MODULE,
-		.of_match_table = of_match_ptr(of_scpsys_match_tbl),
+		.of_match_table = of_scpsys_match_tbl,
 	},
 };
 builtin_platform_driver(scpsys_drv);
-- 
2.35.1

[PATCH AUTOSEL 4.19 02/11] soc: mediatek: Let PMIC Wrapper and SCPSYS depend on OF

[Sasha Levin]

From: Jean Delvare <jdelvare@suse.de>

[ Upstream commit 2778caedb5667239823a29148dfc48b26a8b3c2a ]

With the following configuration options:
CONFIG_OF is not set
CONFIG_MTK_PMIC_WRAP=y
CONFIG_MTK_SCPSYS=y
we get the following build warnings:

  CC      drivers/soc/mediatek/mtk-pmic-wrap.o
drivers/soc/mediatek/mtk-pmic-wrap.c:2138:34: warning: ‘of_pwrap_match_tbl’ defined but not used [-Wunused-const-variable=]
drivers/soc/mediatek/mtk-pmic-wrap.c:1953:34: warning: ‘of_slave_match_tbl’ defined but not used [-Wunused-const-variable=]
  CC      drivers/soc/mediatek/mtk-scpsys.o
drivers/soc/mediatek/mtk-scpsys.c:1084:34: warning: ‘of_scpsys_match_tbl’ defined but not used [-Wunused-const-variable=]

Looking at the code, both drivers can only bind to OF-defined device
nodes, so these drivers are useless without OF and should therefore
depend on it.

Also drop of_match_ptr() from both drivers. We already know what it
will resolve to, so we might as well save cpp some work.

Developers or QA teams who wish to test-build the code can still do
so by enabling CONFIG_OF, which is available on all architectures and
has no dependencies.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/all/202207240252.ZY5hSCNB-lkp@intel.com/
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Chenglin Xu <chenglin.xu@mediatek.com>
Link: https://lore.kernel.org/r/20220730144833.0a0d9825@endymion.delvare
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/mediatek/Kconfig         | 2 ++
 drivers/soc/mediatek/mtk-pmic-wrap.c | 2 +-
 drivers/soc/mediatek/mtk-scpsys.c    | 2 +-
 3 files changed, 4 insertions(+), 2 deletions(-)

diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
index a7d0667338f2..2bb92efd01a8 100644
--- a/drivers/soc/mediatek/Kconfig
+++ b/drivers/soc/mediatek/Kconfig
@@ -15,6 +15,7 @@ config MTK_INFRACFG
 config MTK_PMIC_WRAP
 	tristate "MediaTek PMIC Wrapper Support"
 	depends on RESET_CONTROLLER
+	depends on OF
 	select REGMAP
 	help
 	  Say yes here to add support for MediaTek PMIC Wrapper found
@@ -24,6 +25,7 @@ config MTK_PMIC_WRAP
 config MTK_SCPSYS
 	bool "MediaTek SCPSYS Support"
 	default ARCH_MEDIATEK
+	depends on OF
 	select REGMAP
 	select MTK_INFRACFG
 	select PM_GENERIC_DOMAINS if PM
diff --git a/drivers/soc/mediatek/mtk-pmic-wrap.c b/drivers/soc/mediatek/mtk-pmic-wrap.c
index 011a40b5fb49..0e7dc2f01296 100644
--- a/drivers/soc/mediatek/mtk-pmic-wrap.c
+++ b/drivers/soc/mediatek/mtk-pmic-wrap.c
@@ -1672,7 +1672,7 @@ static int pwrap_probe(struct platform_device *pdev)
 static struct platform_driver pwrap_drv = {
 	.driver = {
 		.name = "mt-pmic-pwrap",
-		.of_match_table = of_match_ptr(of_pwrap_match_tbl),
+		.of_match_table = of_pwrap_match_tbl,
 	},
 	.probe = pwrap_probe,
 };
diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
index ef54f1638d20..06543e41d015 100644
--- a/drivers/soc/mediatek/mtk-scpsys.c
+++ b/drivers/soc/mediatek/mtk-scpsys.c
@@ -1071,7 +1071,7 @@ static struct platform_driver scpsys_drv = {
 		.name = "mtk-scpsys",
 		.suppress_bind_attrs = true,
 		.owner = THIS_MODULE,
-		.of_match_table = of_match_ptr(of_scpsys_match_tbl),
+		.of_match_table = of_scpsys_match_tbl,
 	},
 };
 builtin_platform_driver(scpsys_drv);
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 03/11] ARM: dts: imx6q: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 0193ee6fe964..a28dce3c6457 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -158,6 +158,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 4.19 03/11] ARM: dts: imx6q: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit b11d083c5dcec7c42fe982c854706d404ddd3a5f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6q.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 0193ee6fe964..a28dce3c6457 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -158,6 +158,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 04/11] ARM: dts: imx6dl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index f0607eb41df4..079f77c7e0f0 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -81,6 +81,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 4.19 04/11] ARM: dts: imx6dl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit f5848b95633d598bacf0500e0108dc5961af88c0 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index f0607eb41df4..079f77c7e0f0 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -81,6 +81,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 05/11] ARM: dts: imx6qp: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi
index d91f92f944c5..3633383db706 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@ soc {
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 4.19 05/11] ARM: dts: imx6qp: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 088fe5237435ee2f7ed4450519b2ef58b94c832f ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@940000: '#address-cells' is a required property
sram@940000: '#size-cells' is a required property
sram@940000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qp.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi
index d91f92f944c5..3633383db706 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@ soc {
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 06/11] ARM: dts: imx6sl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 9d19183f40e1..afde0ed6d71a 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -118,6 +118,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 4.19 06/11] ARM: dts: imx6sl: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 60c9213a1d9941a8b33db570796c3f9be8984974 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sl.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index 9d19183f40e1..afde0ed6d71a 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -118,6 +118,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 07/11] ARM: dts: imx6sll: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 7492a83ed9b7a151e2dd11d64b06da7a7f0fa7f9 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 7c7d5c47578e..d7d092a5522a 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -131,6 +131,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		L2: l2-cache@a02000 {
-- 
2.35.1

[PATCH AUTOSEL 4.19 07/11] ARM: dts: imx6sll: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 7492a83ed9b7a151e2dd11d64b06da7a7f0fa7f9 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sll.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index 7c7d5c47578e..d7d092a5522a 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -131,6 +131,9 @@ soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		L2: l2-cache@a02000 {
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 08/11] ARM: dts: imx6sx: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 415432c008b2bce8138841356ba444631cabaa50 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index ae0728df542e..b9ab1118be30 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -167,12 +167,18 @@ soc {
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
-- 
2.35.1

[PATCH AUTOSEL 4.19 08/11] ARM: dts: imx6sx: add missing properties for sram

[Sasha Levin]

From: Alexander Stein <alexander.stein@ew.tq-group.com>

[ Upstream commit 415432c008b2bce8138841356ba444631cabaa50 ]

All 3 properties are required by sram.yaml. Fixes the dtbs_check warning:
sram@900000: '#address-cells' is a required property
sram@900000: '#size-cells' is a required property
sram@900000: 'ranges' is a required property

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6sx.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index ae0728df542e..b9ab1118be30 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -167,12 +167,18 @@ soc {
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 09/11] ARM: orion: fix include path

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 63872304bdb3decd5454f4dd210c25395278ed13 ]

Now that CONFIG_ARCH_MULTIPLATFORM can be disabled anywhere,
there is a build failure for plat-orion:

arch/arm/plat-orion/irq.c:19:10: fatal error: plat/irq.h: No such file or directory

Make the include path unconditional.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/plat-orion/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/plat-orion/Makefile b/arch/arm/plat-orion/Makefile
index 9433605cd290..06c3530d8ad5 100644
--- a/arch/arm/plat-orion/Makefile
+++ b/arch/arm/plat-orion/Makefile
@@ -1,7 +1,7 @@
 #
 # Makefile for the linux kernel.
 #
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+ccflags-y := -I$(srctree)/$(src)/include
 
 orion-gpio-$(CONFIG_GPIOLIB)      += gpio.o
 obj-$(CONFIG_PLAT_ORION_LEGACY)   += irq.o pcie.o time.o common.o mpp.o
-- 
2.35.1

[PATCH AUTOSEL 4.19 09/11] ARM: orion: fix include path

[Sasha Levin]

From: Arnd Bergmann <arnd@arndb.de>

[ Upstream commit 63872304bdb3decd5454f4dd210c25395278ed13 ]

Now that CONFIG_ARCH_MULTIPLATFORM can be disabled anywhere,
there is a build failure for plat-orion:

arch/arm/plat-orion/irq.c:19:10: fatal error: plat/irq.h: No such file or directory

Make the include path unconditional.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/plat-orion/Makefile | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/plat-orion/Makefile b/arch/arm/plat-orion/Makefile
index 9433605cd290..06c3530d8ad5 100644
--- a/arch/arm/plat-orion/Makefile
+++ b/arch/arm/plat-orion/Makefile
@@ -1,7 +1,7 @@
 #
 # Makefile for the linux kernel.
 #
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+ccflags-y := -I$(srctree)/$(src)/include
 
 orion-gpio-$(CONFIG_GPIOLIB)      += gpio.o
 obj-$(CONFIG_PLAT_ORION_LEGACY)   += irq.o pcie.o time.o common.o mpp.o
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Sasha Levin]

From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

[ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]

PXs3 reference board can change each USB port 0 and 1 to device mode
with jumpers. Prepare devicetree sources for USB port 0 and 1.

This specifies dr_mode, pinctrl, and some quirks and removes nodes for
unused phys and vbus-supply properties.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-8-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
 arch/arm64/boot/dts/socionext/Makefile        |  4 +-
 .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
 .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
 4 files changed, 94 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts

diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
index 51f0e69f49fd..21cc91110439 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
@@ -156,11 +156,21 @@ pinctrl_usb0: usb0 {
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index d45441249cb5..c922d9303b69 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -4,4 +4,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld11-ref.dtb \
 	uniphier-ld20-global.dtb \
 	uniphier-ld20-ref.dtb \
-	uniphier-pxs3-ref.dtb
+	uniphier-pxs3-ref.dtb \
+	uniphier-pxs3-ref-gadget0.dtb \
+	uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
new file mode 100644
index 000000000000..7069f51bc120
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #0)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb0_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+};
+
+&usb0_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb0_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb0_hsphy1;
+/delete-node/ &usb0_ssphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
new file mode 100644
index 000000000000..a3cfa8113ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #1)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb1_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb1_hsphy0>, <&usb1_ssphy0>;
+};
+
+&usb1_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb1_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb1_hsphy1;
-- 
2.35.1

[PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Sasha Levin]

From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>

[ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]

PXs3 reference board can change each USB port 0 and 1 to device mode
with jumpers. Prepare devicetree sources for USB port 0 and 1.

This specifies dr_mode, pinctrl, and some quirks and removes nodes for
unused phys and vbus-supply properties.

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-8-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
 arch/arm64/boot/dts/socionext/Makefile        |  4 +-
 .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
 .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
 4 files changed, 94 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
 create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts

diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
index 51f0e69f49fd..21cc91110439 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
@@ -156,11 +156,21 @@ pinctrl_usb0: usb0 {
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index d45441249cb5..c922d9303b69 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -4,4 +4,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld11-ref.dtb \
 	uniphier-ld20-global.dtb \
 	uniphier-ld20-ref.dtb \
-	uniphier-pxs3-ref.dtb
+	uniphier-pxs3-ref.dtb \
+	uniphier-pxs3-ref-gadget0.dtb \
+	uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
new file mode 100644
index 000000000000..7069f51bc120
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #0)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb0_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+};
+
+&usb0_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb0_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb0_hsphy1;
+/delete-node/ &usb0_ssphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
new file mode 100644
index 000000000000..a3cfa8113ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #1)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb1_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb1_hsphy0>, <&usb1_ssphy0>;
+};
+
+&usb1_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb1_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb1_hsphy1;
-- 
2.35.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 4.19 11/11] selftests/cpu-hotplug: Use return instead of exit

[Sasha Levin]

From: Zhao Gongyi <zhaogongyi@huawei.com>

[ Upstream commit 972cf4ce51ef5532d56822af17defb148aac0ccb ]

Some cpus will be left in offline state when online
function exits in some error conditions. Use return
instead of exit to fix it.

Signed-off-by: Zhao Gongyi <zhaogongyi@huawei.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../selftests/cpu-hotplug/cpu-on-off-test.sh        | 13 ++++++++-----
 1 file changed, 8 insertions(+), 5 deletions(-)

diff --git a/tools/testing/selftests/cpu-hotplug/cpu-on-off-test.sh b/tools/testing/selftests/cpu-hotplug/cpu-on-off-test.sh
index 0d26b5e3f966..940b68c940bb 100755
--- a/tools/testing/selftests/cpu-hotplug/cpu-on-off-test.sh
+++ b/tools/testing/selftests/cpu-hotplug/cpu-on-off-test.sh
@@ -4,6 +4,7 @@
 SYSFS=
 # Kselftest framework requirement - SKIP code is 4.
 ksft_skip=4
+retval=0
 
 prerequisite()
 {
@@ -102,10 +103,10 @@ online_cpu_expect_success()
 
 	if ! online_cpu $cpu; then
 		echo $FUNCNAME $cpu: unexpected fail >&2
-		exit 1
+		retval=1
 	elif ! cpu_is_online $cpu; then
 		echo $FUNCNAME $cpu: unexpected offline >&2
-		exit 1
+		retval=1
 	fi
 }
 
@@ -128,10 +129,10 @@ offline_cpu_expect_success()
 
 	if ! offline_cpu $cpu; then
 		echo $FUNCNAME $cpu: unexpected fail >&2
-		exit 1
+		retval=1
 	elif ! cpu_is_offline $cpu; then
 		echo $FUNCNAME $cpu: unexpected offline >&2
-		exit 1
+		retval=1
 	fi
 }
 
@@ -201,7 +202,7 @@ if [ $allcpus -eq 0 ]; then
 		offline_cpu_expect_success $present_max
 		online_cpu $present_max
 	fi
-	exit 0
+	exit $retval
 else
 	echo "Full scope test: all hotplug cpus"
 	echo -e "\t online all offline cpus"
@@ -291,3 +292,5 @@ done
 
 echo 0 > $NOTIFIER_ERR_INJECT_DIR/actions/CPU_DOWN_PREPARE/error
 /sbin/modprobe -q -r cpu-notifier-error-inject
+
+exit $retval
-- 
2.35.1

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Pavel Machek]

[-- Attachment #1: Type: text/plain, Size: 1049 bytes --]

Hi!

> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> 
> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
> 
> PXs3 reference board can change each USB port 0 and 1 to device mode
> with jumpers. Prepare devicetree sources for USB port 0 and 1.
> 
> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
> unused phys and vbus-supply properties.

Why was this autoselected? It is a new feature, not a bugfix.

Best regards,
								Pavel

>  arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
>  arch/arm64/boot/dts/socionext/Makefile        |  4 +-
>  .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
>  .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
>  4 files changed, 94 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 195 bytes --]

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Pavel Machek]

[-- Attachment #1.1: Type: text/plain, Size: 1049 bytes --]

Hi!

> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> 
> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
> 
> PXs3 reference board can change each USB port 0 and 1 to device mode
> with jumpers. Prepare devicetree sources for USB port 0 and 1.
> 
> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
> unused phys and vbus-supply properties.

Why was this autoselected? It is a new feature, not a bugfix.

Best regards,
								Pavel

>  arch/arm/boot/dts/uniphier-pinctrl.dtsi       | 10 +++++
>  arch/arm64/boot/dts/socionext/Makefile        |  4 +-
>  .../socionext/uniphier-pxs3-ref-gadget0.dts   | 41 +++++++++++++++++++
>  .../socionext/uniphier-pxs3-ref-gadget1.dts   | 40 ++++++++++++++++++
>  4 files changed, 94 insertions(+), 1 deletion(-)
>  create mode 100644 arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts

-- 
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 195 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Arnd Bergmann]

On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
> Hi!
>
>> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
>> 
>> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
>> 
>> PXs3 reference board can change each USB port 0 and 1 to device mode
>> with jumpers. Prepare devicetree sources for USB port 0 and 1.
>> 
>> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
>> unused phys and vbus-supply properties.
>
> Why was this autoselected? It is a new feature, not a bugfix.

It also caused a regression now according to the build bots. I 
have not checked, but I assume there are some other patches that
this depends on.

     Arnd

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Arnd Bergmann]

On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
> Hi!
>
>> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
>> 
>> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
>> 
>> PXs3 reference board can change each USB port 0 and 1 to device mode
>> with jumpers. Prepare devicetree sources for USB port 0 and 1.
>> 
>> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
>> unused phys and vbus-supply properties.
>
> Why was this autoselected? It is a new feature, not a bugfix.

It also caused a regression now according to the build bots. I 
have not checked, but I assume there are some other patches that
this depends on.

     Arnd

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Greg KH]

On Fri, Oct 21, 2022 at 08:29:30AM +0200, Arnd Bergmann wrote:
> On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
> > Hi!
> >
> >> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> >> 
> >> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
> >> 
> >> PXs3 reference board can change each USB port 0 and 1 to device mode
> >> with jumpers. Prepare devicetree sources for USB port 0 and 1.
> >> 
> >> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
> >> unused phys and vbus-supply properties.
> >
> > Why was this autoselected? It is a new feature, not a bugfix.
> 
> It also caused a regression now according to the build bots. I 
> have not checked, but I assume there are some other patches that
> this depends on.

Ok, let me go drop this from all trees now, thanks.

greg k-h

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Greg KH]

On Fri, Oct 21, 2022 at 08:29:30AM +0200, Arnd Bergmann wrote:
> On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
> > Hi!
> >
> >> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
> >> 
> >> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
> >> 
> >> PXs3 reference board can change each USB port 0 and 1 to device mode
> >> with jumpers. Prepare devicetree sources for USB port 0 and 1.
> >> 
> >> This specifies dr_mode, pinctrl, and some quirks and removes nodes for
> >> unused phys and vbus-supply properties.
> >
> > Why was this autoselected? It is a new feature, not a bugfix.
> 
> It also caused a regression now according to the build bots. I 
> have not checked, but I assume there are some other patches that
> this depends on.

Ok, let me go drop this from all trees now, thanks.

greg k-h

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Kunihiko Hayashi]

On 2022/10/21 15:54, Greg KH wrote:
> On Fri, Oct 21, 2022 at 08:29:30AM +0200, Arnd Bergmann wrote:
>> On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
>>> Hi!
>>>
>>>> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
>>>>
>>>> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
>>>>
>>>> PXs3 reference board can change each USB port 0 and 1 to device mode
>>>> with jumpers. Prepare devicetree sources for USB port 0 and 1.
>>>>
>>>> This specifies dr_mode, pinctrl, and some quirks and removes nodes
> for
>>>> unused phys and vbus-supply properties.
>>>
>>> Why was this autoselected? It is a new feature, not a bugfix.
>>
>> It also caused a regression now according to the build bots. I
>> have not checked, but I assume there are some other patches that
>> this depends on.
> 
> Ok, let me go drop this from all trees now, thanks.
Sorry for late.
Right, this is not a "fixes" patch, so please drop it from stable.

Thank you,

---
Best Regards
Kunihiko Hayashi

Re: [PATCH AUTOSEL 4.19 10/11] arm64: dts: uniphier: Add USB-device support for PXs3 reference board

[Kunihiko Hayashi]

On 2022/10/21 15:54, Greg KH wrote:
> On Fri, Oct 21, 2022 at 08:29:30AM +0200, Arnd Bergmann wrote:
>> On Mon, Oct 17, 2022, at 13:23, Pavel Machek wrote:
>>> Hi!
>>>
>>>> From: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
>>>>
>>>> [ Upstream commit 19fee1a1096d21ab1f1e712148b5417bda2939a2 ]
>>>>
>>>> PXs3 reference board can change each USB port 0 and 1 to device mode
>>>> with jumpers. Prepare devicetree sources for USB port 0 and 1.
>>>>
>>>> This specifies dr_mode, pinctrl, and some quirks and removes nodes
> for
>>>> unused phys and vbus-supply properties.
>>>
>>> Why was this autoselected? It is a new feature, not a bugfix.
>>
>> It also caused a regression now according to the build bots. I
>> have not checked, but I assume there are some other patches that
>> this depends on.
> 
> Ok, let me go drop this from all trees now, thanks.
Sorry for late.
Right, this is not a "fixes" patch, so please drop it from stable.

Thank you,

---
Best Regards
Kunihiko Hayashi

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel