* [PATCHv4 00/13] Introduce RK806 Support
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Hi,
The Rockchip RK3588 Evaluation Boards use SPI connected RK806
PMICs. Downstream this is handled by a new driver, but apart
from being SPI connected this chip is quite similar to the
ther Rockchip PMICs (also RK806 is promoted to also support
I2C). Thus this series instead updates the RK808 driver(s).
Changelog since PATCHv3:
* https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
* Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
* Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
since the patchset touches all the child drivers anyways.
* rebase to v6.1-rc1
* collected a couple of Acks
* update rk806 DT binding according to DT maintainer feedback
* add missing pinmux config to the rk806 DT binding
* update rk806_spi_bus_write and rk806_spi_bus_read
* replaced some constants with sizeof or defines
* used capitalized comments
* rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
why I prefixed it with regmap_ in the first place
* use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
the switching regulators to correctly report the state
* reordered the first few patches grouping the MFD patches together
Changelog since PATCHv2:
* https://lore.kernel.org/all/20220908003107.220143-1-sebastian.reichel@collabora.com/
* Change DT binding to not allow nldo-reg6
* Fix DT binding to check for [np]ldo-reg instead of [np]ldo_reg
* remove rk806_get_voltage_sel_regmap in favour of regulator_get_voltage_sel_regmap
* drop rk806_set_voltage in favour of regulator_set_voltage_sel_regmap
* use regulator_set_ramp_delay_regmap
* drop possibly incorrect printing of chip id register address in case of errors
Changelog since PATCHv1:
* https://lore.kernel.org/all/20220831215437.117880-1-sebastian.reichel@collabora.com/
* Collect Acked-by
* Avoid if/else checks for regulator id in rk806 regulator driver
* Fix indentation in DTS example section of the rk806 binding
* Use absolute path for regulator.yaml referencing in the rk806 binding
* Reduce pattern for DCDC regulators to only allow 1-10
* replace uppercase name with lowercase ones in regulator names
* replace _ with - in regulator names
-- Sebastian
Sebastian Reichel (13):
clk: RK808: reduce 'struct rk808' usage
regulator: rk808: reduce 'struct rk808' usage
rtc: rk808: reduce 'struct rk808' usage
mfd: rk808: convert to device managed resources
mfd: rk808: use dev_err_probe
mfd: rk808: replace 'struct i2c_client' with 'struct device'
mfd: rk808: split into core and i2c
dt-bindings: mfd: add rk806 binding
mfd: rk8xx: add rk806 support
pinctrl: rk805: add rk806 pinctrl support
regulator: rk808: Use dev_err_probe
regulator: expose regulator_find_closest_bigger
regulator: rk808: add rk806 support
.../bindings/mfd/rockchip,rk806.yaml | 405 +++++++++++++++++
drivers/clk/Kconfig | 2 +-
drivers/clk/clk-rk808.c | 34 +-
drivers/input/misc/Kconfig | 2 +-
drivers/mfd/Kconfig | 21 +-
drivers/mfd/Makefile | 4 +-
drivers/mfd/{rk808.c => rk8xx-core.c} | 351 +++++----------
drivers/mfd/rk8xx-i2c.c | 209 +++++++++
drivers/mfd/rk8xx-spi.c | 115 +++++
drivers/pinctrl/Kconfig | 2 +-
drivers/pinctrl/pinctrl-rk805.c | 189 +++++++-
drivers/power/supply/Kconfig | 2 +-
drivers/regulator/Kconfig | 2 +-
drivers/regulator/helpers.c | 22 +-
drivers/regulator/rk808-regulator.c | 409 ++++++++++++++++-
drivers/rtc/Kconfig | 2 +-
drivers/rtc/rtc-rk808.c | 47 +-
include/linux/mfd/rk808.h | 417 +++++++++++++++++-
include/linux/regulator/driver.h | 2 +
sound/soc/codecs/Kconfig | 2 +-
20 files changed, 1913 insertions(+), 326 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
rename drivers/mfd/{rk808.c => rk8xx-core.c} (70%)
create mode 100644 drivers/mfd/rk8xx-i2c.c
create mode 100644 drivers/mfd/rk8xx-spi.c
--
2.35.1
^ permalink raw reply [flat|nested] 44+ messages in thread
* [PATCHv4 00/13] Introduce RK806 Support
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Hi,
The Rockchip RK3588 Evaluation Boards use SPI connected RK806
PMICs. Downstream this is handled by a new driver, but apart
from being SPI connected this chip is quite similar to the
ther Rockchip PMICs (also RK806 is promoted to also support
I2C). Thus this series instead updates the RK808 driver(s).
Changelog since PATCHv3:
* https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
* Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
* Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
since the patchset touches all the child drivers anyways.
* rebase to v6.1-rc1
* collected a couple of Acks
* update rk806 DT binding according to DT maintainer feedback
* add missing pinmux config to the rk806 DT binding
* update rk806_spi_bus_write and rk806_spi_bus_read
* replaced some constants with sizeof or defines
* used capitalized comments
* rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
why I prefixed it with regmap_ in the first place
* use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
the switching regulators to correctly report the state
* reordered the first few patches grouping the MFD patches together
Changelog since PATCHv2:
* https://lore.kernel.org/all/20220908003107.220143-1-sebastian.reichel@collabora.com/
* Change DT binding to not allow nldo-reg6
* Fix DT binding to check for [np]ldo-reg instead of [np]ldo_reg
* remove rk806_get_voltage_sel_regmap in favour of regulator_get_voltage_sel_regmap
* drop rk806_set_voltage in favour of regulator_set_voltage_sel_regmap
* use regulator_set_ramp_delay_regmap
* drop possibly incorrect printing of chip id register address in case of errors
Changelog since PATCHv1:
* https://lore.kernel.org/all/20220831215437.117880-1-sebastian.reichel@collabora.com/
* Collect Acked-by
* Avoid if/else checks for regulator id in rk806 regulator driver
* Fix indentation in DTS example section of the rk806 binding
* Use absolute path for regulator.yaml referencing in the rk806 binding
* Reduce pattern for DCDC regulators to only allow 1-10
* replace uppercase name with lowercase ones in regulator names
* replace _ with - in regulator names
-- Sebastian
Sebastian Reichel (13):
clk: RK808: reduce 'struct rk808' usage
regulator: rk808: reduce 'struct rk808' usage
rtc: rk808: reduce 'struct rk808' usage
mfd: rk808: convert to device managed resources
mfd: rk808: use dev_err_probe
mfd: rk808: replace 'struct i2c_client' with 'struct device'
mfd: rk808: split into core and i2c
dt-bindings: mfd: add rk806 binding
mfd: rk8xx: add rk806 support
pinctrl: rk805: add rk806 pinctrl support
regulator: rk808: Use dev_err_probe
regulator: expose regulator_find_closest_bigger
regulator: rk808: add rk806 support
.../bindings/mfd/rockchip,rk806.yaml | 405 +++++++++++++++++
drivers/clk/Kconfig | 2 +-
drivers/clk/clk-rk808.c | 34 +-
drivers/input/misc/Kconfig | 2 +-
drivers/mfd/Kconfig | 21 +-
drivers/mfd/Makefile | 4 +-
drivers/mfd/{rk808.c => rk8xx-core.c} | 351 +++++----------
drivers/mfd/rk8xx-i2c.c | 209 +++++++++
drivers/mfd/rk8xx-spi.c | 115 +++++
drivers/pinctrl/Kconfig | 2 +-
drivers/pinctrl/pinctrl-rk805.c | 189 +++++++-
drivers/power/supply/Kconfig | 2 +-
drivers/regulator/Kconfig | 2 +-
drivers/regulator/helpers.c | 22 +-
drivers/regulator/rk808-regulator.c | 409 ++++++++++++++++-
drivers/rtc/Kconfig | 2 +-
drivers/rtc/rtc-rk808.c | 47 +-
include/linux/mfd/rk808.h | 417 +++++++++++++++++-
include/linux/regulator/driver.h | 2 +
sound/soc/codecs/Kconfig | 2 +-
20 files changed, 1913 insertions(+), 326 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
rename drivers/mfd/{rk808.c => rk8xx-core.c} (70%)
create mode 100644 drivers/mfd/rk8xx-i2c.c
create mode 100644 drivers/mfd/rk8xx-spi.c
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* [PATCHv4 01/13] clk: RK808: reduce 'struct rk808' usage
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/clk/clk-rk808.c | 34 ++++++++++++++++------------------
1 file changed, 16 insertions(+), 18 deletions(-)
diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
index 32f833d732ed..f7412b137e5e 100644
--- a/drivers/clk/clk-rk808.c
+++ b/drivers/clk/clk-rk808.c
@@ -12,10 +12,9 @@
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/mfd/rk808.h>
-#include <linux/i2c.h>
struct rk808_clkout {
- struct rk808 *rk808;
+ struct regmap *regmap;
struct clk_hw clkout1_hw;
struct clk_hw clkout2_hw;
};
@@ -31,9 +30,8 @@ static int rk808_clkout2_enable(struct clk_hw *hw, bool enable)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
- return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
+ return regmap_update_bits(rk808_clkout->regmap, RK808_CLK32OUT_REG,
CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
}
@@ -52,10 +50,9 @@ static int rk808_clkout2_is_prepared(struct clk_hw *hw)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
uint32_t val;
- int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
+ int ret = regmap_read(rk808_clkout->regmap, RK808_CLK32OUT_REG, &val);
if (ret < 0)
return ret;
@@ -93,9 +90,8 @@ static int rk817_clkout2_enable(struct clk_hw *hw, bool enable)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
- return regmap_update_bits(rk808->regmap, RK817_SYS_CFG(1),
+ return regmap_update_bits(rk808_clkout->regmap, RK817_SYS_CFG(1),
RK817_CLK32KOUT2_EN,
enable ? RK817_CLK32KOUT2_EN : 0);
}
@@ -115,10 +111,9 @@ static int rk817_clkout2_is_prepared(struct clk_hw *hw)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
unsigned int val;
- int ret = regmap_read(rk808->regmap, RK817_SYS_CFG(1), &val);
+ int ret = regmap_read(rk808_clkout->regmap, RK817_SYS_CFG(1), &val);
if (ret < 0)
return 0;
@@ -153,18 +148,21 @@ static const struct clk_ops *rkpmic_get_ops(long variant)
static int rk808_clkout_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
- struct i2c_client *client = rk808->i2c;
- struct device_node *node = client->dev.of_node;
+ struct device *dev = &pdev->dev;
struct clk_init_data init = {};
struct rk808_clkout *rk808_clkout;
int ret;
- rk808_clkout = devm_kzalloc(&client->dev,
+ dev->of_node = pdev->dev.parent->of_node;
+
+ rk808_clkout = devm_kzalloc(dev,
sizeof(*rk808_clkout), GFP_KERNEL);
if (!rk808_clkout)
return -ENOMEM;
- rk808_clkout->rk808 = rk808;
+ rk808_clkout->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!rk808_clkout->regmap)
+ return -ENODEV;
init.parent_names = NULL;
init.num_parents = 0;
@@ -173,10 +171,10 @@ static int rk808_clkout_probe(struct platform_device *pdev)
rk808_clkout->clkout1_hw.init = &init;
/* optional override of the clockname */
- of_property_read_string_index(node, "clock-output-names",
+ of_property_read_string_index(dev->of_node, "clock-output-names",
0, &init.name);
- ret = devm_clk_hw_register(&client->dev, &rk808_clkout->clkout1_hw);
+ ret = devm_clk_hw_register(dev, &rk808_clkout->clkout1_hw);
if (ret)
return ret;
@@ -185,10 +183,10 @@ static int rk808_clkout_probe(struct platform_device *pdev)
rk808_clkout->clkout2_hw.init = &init;
/* optional override of the clockname */
- of_property_read_string_index(node, "clock-output-names",
+ of_property_read_string_index(dev->of_node, "clock-output-names",
1, &init.name);
- ret = devm_clk_hw_register(&client->dev, &rk808_clkout->clkout2_hw);
+ ret = devm_clk_hw_register(dev, &rk808_clkout->clkout2_hw);
if (ret)
return ret;
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 01/13] clk: RK808: reduce 'struct rk808' usage
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/clk/clk-rk808.c | 34 ++++++++++++++++------------------
1 file changed, 16 insertions(+), 18 deletions(-)
diff --git a/drivers/clk/clk-rk808.c b/drivers/clk/clk-rk808.c
index 32f833d732ed..f7412b137e5e 100644
--- a/drivers/clk/clk-rk808.c
+++ b/drivers/clk/clk-rk808.c
@@ -12,10 +12,9 @@
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/mfd/rk808.h>
-#include <linux/i2c.h>
struct rk808_clkout {
- struct rk808 *rk808;
+ struct regmap *regmap;
struct clk_hw clkout1_hw;
struct clk_hw clkout2_hw;
};
@@ -31,9 +30,8 @@ static int rk808_clkout2_enable(struct clk_hw *hw, bool enable)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
- return regmap_update_bits(rk808->regmap, RK808_CLK32OUT_REG,
+ return regmap_update_bits(rk808_clkout->regmap, RK808_CLK32OUT_REG,
CLK32KOUT2_EN, enable ? CLK32KOUT2_EN : 0);
}
@@ -52,10 +50,9 @@ static int rk808_clkout2_is_prepared(struct clk_hw *hw)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
uint32_t val;
- int ret = regmap_read(rk808->regmap, RK808_CLK32OUT_REG, &val);
+ int ret = regmap_read(rk808_clkout->regmap, RK808_CLK32OUT_REG, &val);
if (ret < 0)
return ret;
@@ -93,9 +90,8 @@ static int rk817_clkout2_enable(struct clk_hw *hw, bool enable)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
- return regmap_update_bits(rk808->regmap, RK817_SYS_CFG(1),
+ return regmap_update_bits(rk808_clkout->regmap, RK817_SYS_CFG(1),
RK817_CLK32KOUT2_EN,
enable ? RK817_CLK32KOUT2_EN : 0);
}
@@ -115,10 +111,9 @@ static int rk817_clkout2_is_prepared(struct clk_hw *hw)
struct rk808_clkout *rk808_clkout = container_of(hw,
struct rk808_clkout,
clkout2_hw);
- struct rk808 *rk808 = rk808_clkout->rk808;
unsigned int val;
- int ret = regmap_read(rk808->regmap, RK817_SYS_CFG(1), &val);
+ int ret = regmap_read(rk808_clkout->regmap, RK817_SYS_CFG(1), &val);
if (ret < 0)
return 0;
@@ -153,18 +148,21 @@ static const struct clk_ops *rkpmic_get_ops(long variant)
static int rk808_clkout_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
- struct i2c_client *client = rk808->i2c;
- struct device_node *node = client->dev.of_node;
+ struct device *dev = &pdev->dev;
struct clk_init_data init = {};
struct rk808_clkout *rk808_clkout;
int ret;
- rk808_clkout = devm_kzalloc(&client->dev,
+ dev->of_node = pdev->dev.parent->of_node;
+
+ rk808_clkout = devm_kzalloc(dev,
sizeof(*rk808_clkout), GFP_KERNEL);
if (!rk808_clkout)
return -ENOMEM;
- rk808_clkout->rk808 = rk808;
+ rk808_clkout->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!rk808_clkout->regmap)
+ return -ENODEV;
init.parent_names = NULL;
init.num_parents = 0;
@@ -173,10 +171,10 @@ static int rk808_clkout_probe(struct platform_device *pdev)
rk808_clkout->clkout1_hw.init = &init;
/* optional override of the clockname */
- of_property_read_string_index(node, "clock-output-names",
+ of_property_read_string_index(dev->of_node, "clock-output-names",
0, &init.name);
- ret = devm_clk_hw_register(&client->dev, &rk808_clkout->clkout1_hw);
+ ret = devm_clk_hw_register(dev, &rk808_clkout->clkout1_hw);
if (ret)
return ret;
@@ -185,10 +183,10 @@ static int rk808_clkout_probe(struct platform_device *pdev)
rk808_clkout->clkout2_hw.init = &init;
/* optional override of the clockname */
- of_property_read_string_index(node, "clock-output-names",
+ of_property_read_string_index(dev->of_node, "clock-output-names",
1, &init.name);
- ret = devm_clk_hw_register(&client->dev, &rk808_clkout->clkout2_hw);
+ ret = devm_clk_hw_register(dev, &rk808_clkout->clkout2_hw);
if (ret)
return ret;
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 02/13] regulator: rk808: reduce 'struct rk808' usage
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 20 ++++++++++++--------
1 file changed, 12 insertions(+), 8 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index 127dc2e2e690..ce9c64cadeba 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -14,7 +14,6 @@
#include <linux/delay.h>
#include <linux/gpio.h>
-#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
@@ -1286,19 +1285,23 @@ static int rk808_regulator_dt_parse_pdata(struct device *dev,
static int rk808_regulator_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
- struct i2c_client *client = rk808->i2c;
struct regulator_config config = {};
struct regulator_dev *rk808_rdev;
struct rk808_regulator_data *pdata;
const struct regulator_desc *regulators;
+ struct regmap *regmap;
int ret, i, nregulators;
+ regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!regmap)
+ return -ENODEV;
+
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
- ret = rk808_regulator_dt_parse_pdata(&pdev->dev, &client->dev,
- rk808->regmap, pdata);
+ ret = rk808_regulator_dt_parse_pdata(&pdev->dev, pdev->dev.parent,
+ regmap, pdata);
if (ret < 0)
return ret;
@@ -1326,21 +1329,22 @@ static int rk808_regulator_probe(struct platform_device *pdev)
nregulators = RK818_NUM_REGULATORS;
break;
default:
- dev_err(&client->dev, "unsupported RK8XX ID %lu\n",
+ dev_err(&pdev->dev, "unsupported RK8XX ID %lu\n",
rk808->variant);
return -EINVAL;
}
- config.dev = &client->dev;
+ config.dev = &pdev->dev;
+ config.dev->of_node = pdev->dev.parent->of_node;
config.driver_data = pdata;
- config.regmap = rk808->regmap;
+ config.regmap = regmap;
/* Instantiate the regulators */
for (i = 0; i < nregulators; i++) {
rk808_rdev = devm_regulator_register(&pdev->dev,
®ulators[i], &config);
if (IS_ERR(rk808_rdev)) {
- dev_err(&client->dev,
+ dev_err(&pdev->dev,
"failed to register %d regulator\n", i);
return PTR_ERR(rk808_rdev);
}
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 02/13] regulator: rk808: reduce 'struct rk808' usage
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 20 ++++++++++++--------
1 file changed, 12 insertions(+), 8 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index 127dc2e2e690..ce9c64cadeba 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -14,7 +14,6 @@
#include <linux/delay.h>
#include <linux/gpio.h>
-#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
@@ -1286,19 +1285,23 @@ static int rk808_regulator_dt_parse_pdata(struct device *dev,
static int rk808_regulator_probe(struct platform_device *pdev)
{
struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
- struct i2c_client *client = rk808->i2c;
struct regulator_config config = {};
struct regulator_dev *rk808_rdev;
struct rk808_regulator_data *pdata;
const struct regulator_desc *regulators;
+ struct regmap *regmap;
int ret, i, nregulators;
+ regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!regmap)
+ return -ENODEV;
+
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata)
return -ENOMEM;
- ret = rk808_regulator_dt_parse_pdata(&pdev->dev, &client->dev,
- rk808->regmap, pdata);
+ ret = rk808_regulator_dt_parse_pdata(&pdev->dev, pdev->dev.parent,
+ regmap, pdata);
if (ret < 0)
return ret;
@@ -1326,21 +1329,22 @@ static int rk808_regulator_probe(struct platform_device *pdev)
nregulators = RK818_NUM_REGULATORS;
break;
default:
- dev_err(&client->dev, "unsupported RK8XX ID %lu\n",
+ dev_err(&pdev->dev, "unsupported RK8XX ID %lu\n",
rk808->variant);
return -EINVAL;
}
- config.dev = &client->dev;
+ config.dev = &pdev->dev;
+ config.dev->of_node = pdev->dev.parent->of_node;
config.driver_data = pdata;
- config.regmap = rk808->regmap;
+ config.regmap = regmap;
/* Instantiate the regulators */
for (i = 0; i < nregulators; i++) {
rk808_rdev = devm_regulator_register(&pdev->dev,
®ulators[i], &config);
if (IS_ERR(rk808_rdev)) {
- dev_err(&client->dev,
+ dev_err(&pdev->dev,
"failed to register %d regulator\n", i);
return PTR_ERR(rk808_rdev);
}
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 03/13] rtc: rk808: reduce 'struct rk808' usage
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/rtc/rtc-rk808.c | 47 ++++++++++++++++++-----------------------
1 file changed, 20 insertions(+), 27 deletions(-)
diff --git a/drivers/rtc/rtc-rk808.c b/drivers/rtc/rtc-rk808.c
index e920da8c08da..2d9bcb3ce1e3 100644
--- a/drivers/rtc/rtc-rk808.c
+++ b/drivers/rtc/rtc-rk808.c
@@ -14,7 +14,6 @@
#include <linux/bcd.h>
#include <linux/mfd/rk808.h>
#include <linux/platform_device.h>
-#include <linux/i2c.h>
/* RTC_CTRL_REG bitfields */
#define BIT_RTC_CTRL_REG_STOP_RTC_M BIT(0)
@@ -51,7 +50,7 @@ struct rk_rtc_compat_reg {
};
struct rk808_rtc {
- struct rk808 *rk808;
+ struct regmap *regmap;
struct rtc_device *rtc;
struct rk_rtc_compat_reg *creg;
int irq;
@@ -97,12 +96,11 @@ static void gregorian_to_rockchip(struct rtc_time *tm)
static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 rtc_data[NUM_TIME_REGS];
int ret;
/* Force an update of the shadowed registers right now */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
BIT_RTC_CTRL_REG_RTC_GET_TIME);
if (ret) {
@@ -116,7 +114,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
* 32khz. If we clear the GET_TIME bit here, the time of i2c transfer
* certainly more than 31.25us: 16 * 2.5us at 400kHz bus frequency.
*/
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
0);
if (ret) {
@@ -124,7 +122,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_read(rk808->regmap, rk808_rtc->creg->seconds_reg,
+ ret = regmap_bulk_read(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bulk read rtc_data: %d\n", ret);
@@ -148,7 +146,6 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 rtc_data[NUM_TIME_REGS];
int ret;
@@ -163,7 +160,7 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
rtc_data[6] = bin2bcd(tm->tm_wday);
/* Stop RTC while updating the RTC registers */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M,
BIT_RTC_CTRL_REG_STOP_RTC_M);
if (ret) {
@@ -171,14 +168,14 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_write(rk808->regmap, rk808_rtc->creg->seconds_reg,
+ ret = regmap_bulk_write(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bull write rtc_data: %d\n", ret);
return ret;
}
/* Start RTC again */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M, 0);
if (ret) {
dev_err(dev, "Failed to update RTC control: %d\n", ret);
@@ -191,12 +188,11 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 alrm_data[NUM_ALARM_REGS];
uint32_t int_reg;
int ret;
- ret = regmap_bulk_read(rk808->regmap,
+ ret = regmap_bulk_read(rk808_rtc->regmap,
rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
if (ret) {
@@ -212,7 +208,7 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
rockchip_to_gregorian(&alrm->time);
- ret = regmap_read(rk808->regmap, rk808_rtc->creg->int_reg, &int_reg);
+ ret = regmap_read(rk808_rtc->regmap, rk808_rtc->creg->int_reg, &int_reg);
if (ret) {
dev_err(dev, "Failed to read RTC INT REG: %d\n", ret);
return ret;
@@ -228,10 +224,9 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
{
- struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M, 0);
return ret;
@@ -239,10 +234,9 @@ static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
{
- struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
@@ -252,7 +246,6 @@ static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 alrm_data[NUM_ALARM_REGS];
int ret;
@@ -272,7 +265,7 @@ static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm_data[4] = bin2bcd(alrm->time.tm_mon + 1);
alrm_data[5] = bin2bcd(alrm->time.tm_year - 100);
- ret = regmap_bulk_write(rk808->regmap,
+ ret = regmap_bulk_write(rk808_rtc->regmap,
rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
if (ret) {
@@ -313,20 +306,18 @@ static int rk808_rtc_alarm_irq_enable(struct device *dev,
static irqreturn_t rk808_alarm_irq(int irq, void *data)
{
struct rk808_rtc *rk808_rtc = data;
- struct rk808 *rk808 = rk808_rtc->rk808;
- struct i2c_client *client = rk808->i2c;
int ret;
- ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
+ ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
- dev_err(&client->dev,
+ dev_err(&rk808_rtc->rtc->dev,
"%s:Failed to update RTC status: %d\n", __func__, ret);
return ret;
}
rtc_update_irq(rk808_rtc->rtc, 1, RTC_IRQF | RTC_AF);
- dev_dbg(&client->dev,
+ dev_dbg(&rk808_rtc->rtc->dev,
"%s:irq=%d\n", __func__, irq);
return IRQ_HANDLED;
}
@@ -404,10 +395,12 @@ static int rk808_rtc_probe(struct platform_device *pdev)
break;
}
platform_set_drvdata(pdev, rk808_rtc);
- rk808_rtc->rk808 = rk808;
+ rk808_rtc->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!rk808_rtc->regmap)
+ return -ENODEV;
/* start rtc running by default, and use shadowed timer. */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M |
BIT_RTC_CTRL_REG_RTC_READSEL_M,
BIT_RTC_CTRL_REG_RTC_READSEL_M);
@@ -417,7 +410,7 @@ static int rk808_rtc_probe(struct platform_device *pdev)
return ret;
}
- ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
+ ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
dev_err(&pdev->dev,
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 03/13] rtc: rk808: reduce 'struct rk808' usage
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Reduce usage of 'struct rk808' (driver data of the parent MFD), so
that only the chip variant field is still being accessed directly.
This allows restructuring the MFD driver to support SPI based
PMICs.
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/rtc/rtc-rk808.c | 47 ++++++++++++++++++-----------------------
1 file changed, 20 insertions(+), 27 deletions(-)
diff --git a/drivers/rtc/rtc-rk808.c b/drivers/rtc/rtc-rk808.c
index e920da8c08da..2d9bcb3ce1e3 100644
--- a/drivers/rtc/rtc-rk808.c
+++ b/drivers/rtc/rtc-rk808.c
@@ -14,7 +14,6 @@
#include <linux/bcd.h>
#include <linux/mfd/rk808.h>
#include <linux/platform_device.h>
-#include <linux/i2c.h>
/* RTC_CTRL_REG bitfields */
#define BIT_RTC_CTRL_REG_STOP_RTC_M BIT(0)
@@ -51,7 +50,7 @@ struct rk_rtc_compat_reg {
};
struct rk808_rtc {
- struct rk808 *rk808;
+ struct regmap *regmap;
struct rtc_device *rtc;
struct rk_rtc_compat_reg *creg;
int irq;
@@ -97,12 +96,11 @@ static void gregorian_to_rockchip(struct rtc_time *tm)
static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 rtc_data[NUM_TIME_REGS];
int ret;
/* Force an update of the shadowed registers right now */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
BIT_RTC_CTRL_REG_RTC_GET_TIME);
if (ret) {
@@ -116,7 +114,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
* 32khz. If we clear the GET_TIME bit here, the time of i2c transfer
* certainly more than 31.25us: 16 * 2.5us at 400kHz bus frequency.
*/
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_RTC_GET_TIME,
0);
if (ret) {
@@ -124,7 +122,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_read(rk808->regmap, rk808_rtc->creg->seconds_reg,
+ ret = regmap_bulk_read(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bulk read rtc_data: %d\n", ret);
@@ -148,7 +146,6 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 rtc_data[NUM_TIME_REGS];
int ret;
@@ -163,7 +160,7 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
rtc_data[6] = bin2bcd(tm->tm_wday);
/* Stop RTC while updating the RTC registers */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M,
BIT_RTC_CTRL_REG_STOP_RTC_M);
if (ret) {
@@ -171,14 +168,14 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
return ret;
}
- ret = regmap_bulk_write(rk808->regmap, rk808_rtc->creg->seconds_reg,
+ ret = regmap_bulk_write(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
rtc_data, NUM_TIME_REGS);
if (ret) {
dev_err(dev, "Failed to bull write rtc_data: %d\n", ret);
return ret;
}
/* Start RTC again */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M, 0);
if (ret) {
dev_err(dev, "Failed to update RTC control: %d\n", ret);
@@ -191,12 +188,11 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 alrm_data[NUM_ALARM_REGS];
uint32_t int_reg;
int ret;
- ret = regmap_bulk_read(rk808->regmap,
+ ret = regmap_bulk_read(rk808_rtc->regmap,
rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
if (ret) {
@@ -212,7 +208,7 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
rockchip_to_gregorian(&alrm->time);
- ret = regmap_read(rk808->regmap, rk808_rtc->creg->int_reg, &int_reg);
+ ret = regmap_read(rk808_rtc->regmap, rk808_rtc->creg->int_reg, &int_reg);
if (ret) {
dev_err(dev, "Failed to read RTC INT REG: %d\n", ret);
return ret;
@@ -228,10 +224,9 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
{
- struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M, 0);
return ret;
@@ -239,10 +234,9 @@ static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
{
- struct rk808 *rk808 = rk808_rtc->rk808;
int ret;
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M,
BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
@@ -252,7 +246,6 @@ static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
- struct rk808 *rk808 = rk808_rtc->rk808;
u8 alrm_data[NUM_ALARM_REGS];
int ret;
@@ -272,7 +265,7 @@ static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
alrm_data[4] = bin2bcd(alrm->time.tm_mon + 1);
alrm_data[5] = bin2bcd(alrm->time.tm_year - 100);
- ret = regmap_bulk_write(rk808->regmap,
+ ret = regmap_bulk_write(rk808_rtc->regmap,
rk808_rtc->creg->alarm_seconds_reg,
alrm_data, NUM_ALARM_REGS);
if (ret) {
@@ -313,20 +306,18 @@ static int rk808_rtc_alarm_irq_enable(struct device *dev,
static irqreturn_t rk808_alarm_irq(int irq, void *data)
{
struct rk808_rtc *rk808_rtc = data;
- struct rk808 *rk808 = rk808_rtc->rk808;
- struct i2c_client *client = rk808->i2c;
int ret;
- ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
+ ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
- dev_err(&client->dev,
+ dev_err(&rk808_rtc->rtc->dev,
"%s:Failed to update RTC status: %d\n", __func__, ret);
return ret;
}
rtc_update_irq(rk808_rtc->rtc, 1, RTC_IRQF | RTC_AF);
- dev_dbg(&client->dev,
+ dev_dbg(&rk808_rtc->rtc->dev,
"%s:irq=%d\n", __func__, irq);
return IRQ_HANDLED;
}
@@ -404,10 +395,12 @@ static int rk808_rtc_probe(struct platform_device *pdev)
break;
}
platform_set_drvdata(pdev, rk808_rtc);
- rk808_rtc->rk808 = rk808;
+ rk808_rtc->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!rk808_rtc->regmap)
+ return -ENODEV;
/* start rtc running by default, and use shadowed timer. */
- ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
+ ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
BIT_RTC_CTRL_REG_STOP_RTC_M |
BIT_RTC_CTRL_REG_RTC_READSEL_M,
BIT_RTC_CTRL_REG_RTC_READSEL_M);
@@ -417,7 +410,7 @@ static int rk808_rtc_probe(struct platform_device *pdev)
return ret;
}
- ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
+ ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
RTC_STATUS_MASK);
if (ret) {
dev_err(&pdev->dev,
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 04/13] mfd: rk808: convert to device managed resources
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Fully convert the driver to device managed resources.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 64 ++++++++++++++++-----------------------------
1 file changed, 22 insertions(+), 42 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index e00da7c7e3b1..e2e7a2c85019 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -541,13 +541,11 @@ static const struct regmap_irq_chip rk818_irq_chip = {
.init_ack_masked = true,
};
-static struct i2c_client *rk808_i2c_client;
-
-static void rk808_pm_power_off(void)
+static int rk808_power_off(struct sys_off_data *data)
{
+ struct rk808 *rk808 = data->cb_data;
int ret;
unsigned int reg, bit;
- struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
switch (rk808->variant) {
case RK805_ID:
@@ -568,16 +566,18 @@ static void rk808_pm_power_off(void)
bit = DEV_OFF;
break;
default:
- return;
+ return NOTIFY_DONE;
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808_i2c_client->dev, "Failed to shutdown device!\n");
+ dev_err(&rk808->i2c->dev, "Failed to shutdown device!\n");
+
+ return NOTIFY_DONE;
}
-static int rk808_restart_notify(struct notifier_block *this, unsigned long mode, void *cmd)
+static int rk808_restart(struct sys_off_data *data)
{
- struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+ struct rk808 *rk808 = data->cb_data;
unsigned int reg, bit;
int ret;
@@ -593,16 +593,11 @@ static int rk808_restart_notify(struct notifier_block *this, unsigned long mode,
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808_i2c_client->dev, "Failed to restart device!\n");
+ dev_err(&rk808->i2c->dev, "Failed to restart device!\n");
return NOTIFY_DONE;
}
-static struct notifier_block rk808_restart_handler = {
- .notifier_call = rk808_restart_notify,
- .priority = 192,
-};
-
static void rk8xx_shutdown(struct i2c_client *client)
{
struct rk808 *rk808 = i2c_get_clientdata(client);
@@ -739,9 +734,9 @@ static int rk808_probe(struct i2c_client *client,
return -EINVAL;
}
- ret = regmap_add_irq_chip(rk808->regmap, client->irq,
- IRQF_ONESHOT, -1,
- rk808->regmap_irq_chip, &rk808->irq_data);
+ ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
+ IRQF_ONESHOT, -1,
+ rk808->regmap_irq_chip, &rk808->irq_data);
if (ret) {
dev_err(&client->dev, "Failed to add irq_chip %d\n", ret);
return ret;
@@ -765,17 +760,23 @@ static int rk808_probe(struct i2c_client *client,
regmap_irq_get_domain(rk808->irq_data));
if (ret) {
dev_err(&client->dev, "failed to add MFD devices %d\n", ret);
- goto err_irq;
+ return ret;
}
if (of_property_read_bool(np, "rockchip,system-power-controller")) {
- rk808_i2c_client = client;
- pm_power_off = rk808_pm_power_off;
+ ret = devm_register_sys_off_handler(&client->dev,
+ SYS_OFF_MODE_POWER_OFF_PREPARE, SYS_OFF_PRIO_HIGH,
+ &rk808_power_off, rk808);
+ if (ret)
+ return dev_err_probe(&client->dev, ret,
+ "failed to register poweroff handler\n");
switch (rk808->variant) {
case RK809_ID:
case RK817_ID:
- ret = register_restart_handler(&rk808_restart_handler);
+ ret = devm_register_sys_off_handler(&client->dev,
+ SYS_OFF_MODE_RESTART, SYS_OFF_PRIO_HIGH,
+ &rk808_restart, rk808);
if (ret)
dev_warn(&client->dev, "failed to register rst handler, %d\n", ret);
break;
@@ -786,26 +787,6 @@ static int rk808_probe(struct i2c_client *client,
}
return 0;
-
-err_irq:
- regmap_del_irq_chip(client->irq, rk808->irq_data);
- return ret;
-}
-
-static void rk808_remove(struct i2c_client *client)
-{
- struct rk808 *rk808 = i2c_get_clientdata(client);
-
- regmap_del_irq_chip(client->irq, rk808->irq_data);
-
- /**
- * pm_power_off may points to a function from another module.
- * Check if the pointer is set by us and only then overwrite it.
- */
- if (pm_power_off == rk808_pm_power_off)
- pm_power_off = NULL;
-
- unregister_restart_handler(&rk808_restart_handler);
}
static int __maybe_unused rk8xx_suspend(struct device *dev)
@@ -862,7 +843,6 @@ static struct i2c_driver rk808_i2c_driver = {
.pm = &rk8xx_pm_ops,
},
.probe = rk808_probe,
- .remove = rk808_remove,
.shutdown = rk8xx_shutdown,
};
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 04/13] mfd: rk808: convert to device managed resources
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Fully convert the driver to device managed resources.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 64 ++++++++++++++++-----------------------------
1 file changed, 22 insertions(+), 42 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index e00da7c7e3b1..e2e7a2c85019 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -541,13 +541,11 @@ static const struct regmap_irq_chip rk818_irq_chip = {
.init_ack_masked = true,
};
-static struct i2c_client *rk808_i2c_client;
-
-static void rk808_pm_power_off(void)
+static int rk808_power_off(struct sys_off_data *data)
{
+ struct rk808 *rk808 = data->cb_data;
int ret;
unsigned int reg, bit;
- struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
switch (rk808->variant) {
case RK805_ID:
@@ -568,16 +566,18 @@ static void rk808_pm_power_off(void)
bit = DEV_OFF;
break;
default:
- return;
+ return NOTIFY_DONE;
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808_i2c_client->dev, "Failed to shutdown device!\n");
+ dev_err(&rk808->i2c->dev, "Failed to shutdown device!\n");
+
+ return NOTIFY_DONE;
}
-static int rk808_restart_notify(struct notifier_block *this, unsigned long mode, void *cmd)
+static int rk808_restart(struct sys_off_data *data)
{
- struct rk808 *rk808 = i2c_get_clientdata(rk808_i2c_client);
+ struct rk808 *rk808 = data->cb_data;
unsigned int reg, bit;
int ret;
@@ -593,16 +593,11 @@ static int rk808_restart_notify(struct notifier_block *this, unsigned long mode,
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808_i2c_client->dev, "Failed to restart device!\n");
+ dev_err(&rk808->i2c->dev, "Failed to restart device!\n");
return NOTIFY_DONE;
}
-static struct notifier_block rk808_restart_handler = {
- .notifier_call = rk808_restart_notify,
- .priority = 192,
-};
-
static void rk8xx_shutdown(struct i2c_client *client)
{
struct rk808 *rk808 = i2c_get_clientdata(client);
@@ -739,9 +734,9 @@ static int rk808_probe(struct i2c_client *client,
return -EINVAL;
}
- ret = regmap_add_irq_chip(rk808->regmap, client->irq,
- IRQF_ONESHOT, -1,
- rk808->regmap_irq_chip, &rk808->irq_data);
+ ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
+ IRQF_ONESHOT, -1,
+ rk808->regmap_irq_chip, &rk808->irq_data);
if (ret) {
dev_err(&client->dev, "Failed to add irq_chip %d\n", ret);
return ret;
@@ -765,17 +760,23 @@ static int rk808_probe(struct i2c_client *client,
regmap_irq_get_domain(rk808->irq_data));
if (ret) {
dev_err(&client->dev, "failed to add MFD devices %d\n", ret);
- goto err_irq;
+ return ret;
}
if (of_property_read_bool(np, "rockchip,system-power-controller")) {
- rk808_i2c_client = client;
- pm_power_off = rk808_pm_power_off;
+ ret = devm_register_sys_off_handler(&client->dev,
+ SYS_OFF_MODE_POWER_OFF_PREPARE, SYS_OFF_PRIO_HIGH,
+ &rk808_power_off, rk808);
+ if (ret)
+ return dev_err_probe(&client->dev, ret,
+ "failed to register poweroff handler\n");
switch (rk808->variant) {
case RK809_ID:
case RK817_ID:
- ret = register_restart_handler(&rk808_restart_handler);
+ ret = devm_register_sys_off_handler(&client->dev,
+ SYS_OFF_MODE_RESTART, SYS_OFF_PRIO_HIGH,
+ &rk808_restart, rk808);
if (ret)
dev_warn(&client->dev, "failed to register rst handler, %d\n", ret);
break;
@@ -786,26 +787,6 @@ static int rk808_probe(struct i2c_client *client,
}
return 0;
-
-err_irq:
- regmap_del_irq_chip(client->irq, rk808->irq_data);
- return ret;
-}
-
-static void rk808_remove(struct i2c_client *client)
-{
- struct rk808 *rk808 = i2c_get_clientdata(client);
-
- regmap_del_irq_chip(client->irq, rk808->irq_data);
-
- /**
- * pm_power_off may points to a function from another module.
- * Check if the pointer is set by us and only then overwrite it.
- */
- if (pm_power_off == rk808_pm_power_off)
- pm_power_off = NULL;
-
- unregister_restart_handler(&rk808_restart_handler);
}
static int __maybe_unused rk8xx_suspend(struct device *dev)
@@ -862,7 +843,6 @@ static struct i2c_driver rk808_i2c_driver = {
.pm = &rk8xx_pm_ops,
},
.probe = rk808_probe,
- .remove = rk808_remove,
.shutdown = rk8xx_shutdown,
};
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 05/13] mfd: rk808: use dev_err_probe
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Use dev_err_probe instead of dev_err in probe function,
which simplifies code a little bit and prints the error
code.
Also drop possibly incorrect printing of chip id registers
while touching the error message.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 48 +++++++++++++++------------------------------
1 file changed, 16 insertions(+), 32 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index e2e7a2c85019..5e0e5f320525 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -664,18 +664,12 @@ static int rk808_probe(struct i2c_client *client,
/* Read chip variant */
msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
- if (msb < 0) {
- dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
- RK808_ID_MSB);
- return msb;
- }
+ if (msb < 0)
+ return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
- if (lsb < 0) {
- dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
- RK808_ID_LSB);
- return lsb;
- }
+ if (lsb < 0)
+ return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
rk808->variant = ((msb << 8) | lsb) & RK8XX_ID_MSK;
dev_info(&client->dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
@@ -724,44 +718,34 @@ static int rk808_probe(struct i2c_client *client,
i2c_set_clientdata(client, rk808);
rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
- if (IS_ERR(rk808->regmap)) {
- dev_err(&client->dev, "regmap initialization failed\n");
- return PTR_ERR(rk808->regmap);
- }
+ if (IS_ERR(rk808->regmap))
+ return dev_err_probe(&client->dev, PTR_ERR(rk808->regmap),
+ "regmap initialization failed\n");
- if (!client->irq) {
- dev_err(&client->dev, "No interrupt support, no core IRQ\n");
- return -EINVAL;
- }
+ if (!client->irq)
+ return dev_err_probe(&client->dev, -EINVAL, "No interrupt support, no core IRQ\n");
ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
IRQF_ONESHOT, -1,
rk808->regmap_irq_chip, &rk808->irq_data);
- if (ret) {
- dev_err(&client->dev, "Failed to add irq_chip %d\n", ret);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "Failed to add irq_chip\n");
for (i = 0; i < nr_pre_init_regs; i++) {
ret = regmap_update_bits(rk808->regmap,
pre_init_reg[i].addr,
pre_init_reg[i].mask,
pre_init_reg[i].value);
- if (ret) {
- dev_err(&client->dev,
- "0x%x write err\n",
- pre_init_reg[i].addr);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "0x%x write err\n",
+ pre_init_reg[i].addr);
}
ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
- if (ret) {
- dev_err(&client->dev, "failed to add MFD devices %d\n", ret);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "failed to add MFD devices\n");
if (of_property_read_bool(np, "rockchip,system-power-controller")) {
ret = devm_register_sys_off_handler(&client->dev,
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 05/13] mfd: rk808: use dev_err_probe
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Use dev_err_probe instead of dev_err in probe function,
which simplifies code a little bit and prints the error
code.
Also drop possibly incorrect printing of chip id registers
while touching the error message.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 48 +++++++++++++++------------------------------
1 file changed, 16 insertions(+), 32 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index e2e7a2c85019..5e0e5f320525 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -664,18 +664,12 @@ static int rk808_probe(struct i2c_client *client,
/* Read chip variant */
msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
- if (msb < 0) {
- dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
- RK808_ID_MSB);
- return msb;
- }
+ if (msb < 0)
+ return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
- if (lsb < 0) {
- dev_err(&client->dev, "failed to read the chip id at 0x%x\n",
- RK808_ID_LSB);
- return lsb;
- }
+ if (lsb < 0)
+ return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
rk808->variant = ((msb << 8) | lsb) & RK8XX_ID_MSK;
dev_info(&client->dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
@@ -724,44 +718,34 @@ static int rk808_probe(struct i2c_client *client,
i2c_set_clientdata(client, rk808);
rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
- if (IS_ERR(rk808->regmap)) {
- dev_err(&client->dev, "regmap initialization failed\n");
- return PTR_ERR(rk808->regmap);
- }
+ if (IS_ERR(rk808->regmap))
+ return dev_err_probe(&client->dev, PTR_ERR(rk808->regmap),
+ "regmap initialization failed\n");
- if (!client->irq) {
- dev_err(&client->dev, "No interrupt support, no core IRQ\n");
- return -EINVAL;
- }
+ if (!client->irq)
+ return dev_err_probe(&client->dev, -EINVAL, "No interrupt support, no core IRQ\n");
ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
IRQF_ONESHOT, -1,
rk808->regmap_irq_chip, &rk808->irq_data);
- if (ret) {
- dev_err(&client->dev, "Failed to add irq_chip %d\n", ret);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "Failed to add irq_chip\n");
for (i = 0; i < nr_pre_init_regs; i++) {
ret = regmap_update_bits(rk808->regmap,
pre_init_reg[i].addr,
pre_init_reg[i].mask,
pre_init_reg[i].value);
- if (ret) {
- dev_err(&client->dev,
- "0x%x write err\n",
- pre_init_reg[i].addr);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "0x%x write err\n",
+ pre_init_reg[i].addr);
}
ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
- if (ret) {
- dev_err(&client->dev, "failed to add MFD devices %d\n", ret);
- return ret;
- }
+ if (ret)
+ return dev_err_probe(&client->dev, ret, "failed to add MFD devices\n");
if (of_property_read_bool(np, "rockchip,system-power-controller")) {
ret = devm_register_sys_off_handler(&client->dev,
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 06/13] mfd: rk808: replace 'struct i2c_client' with 'struct device'
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Put 'struct device' pointer into the MFD platform_data instead
of the 'struct i2c_client' pointer. This simplifies the code
and prepares the MFD for SPI support.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 6 +++---
include/linux/mfd/rk808.h | 2 +-
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index 5e0e5f320525..b154ca96d812 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -570,7 +570,7 @@ static int rk808_power_off(struct sys_off_data *data)
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808->i2c->dev, "Failed to shutdown device!\n");
+ dev_err(rk808->dev, "Failed to shutdown device!\n");
return NOTIFY_DONE;
}
@@ -593,7 +593,7 @@ static int rk808_restart(struct sys_off_data *data)
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808->i2c->dev, "Failed to restart device!\n");
+ dev_err(rk808->dev, "Failed to restart device!\n");
return NOTIFY_DONE;
}
@@ -714,7 +714,7 @@ static int rk808_probe(struct i2c_client *client,
return -EINVAL;
}
- rk808->i2c = client;
+ rk808->dev = &client->dev;
i2c_set_clientdata(client, rk808);
rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 9af1f3105f80..a89ddd9ba68e 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -787,7 +787,7 @@ enum {
};
struct rk808 {
- struct i2c_client *i2c;
+ struct device *dev;
struct regmap_irq_chip_data *irq_data;
struct regmap *regmap;
long variant;
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 06/13] mfd: rk808: replace 'struct i2c_client' with 'struct device'
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Put 'struct device' pointer into the MFD platform_data instead
of the 'struct i2c_client' pointer. This simplifies the code
and prepares the MFD for SPI support.
Acked-for-MFD-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/rk808.c | 6 +++---
include/linux/mfd/rk808.h | 2 +-
2 files changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk808.c
index 5e0e5f320525..b154ca96d812 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk808.c
@@ -570,7 +570,7 @@ static int rk808_power_off(struct sys_off_data *data)
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808->i2c->dev, "Failed to shutdown device!\n");
+ dev_err(rk808->dev, "Failed to shutdown device!\n");
return NOTIFY_DONE;
}
@@ -593,7 +593,7 @@ static int rk808_restart(struct sys_off_data *data)
}
ret = regmap_update_bits(rk808->regmap, reg, bit, bit);
if (ret)
- dev_err(&rk808->i2c->dev, "Failed to restart device!\n");
+ dev_err(rk808->dev, "Failed to restart device!\n");
return NOTIFY_DONE;
}
@@ -714,7 +714,7 @@ static int rk808_probe(struct i2c_client *client,
return -EINVAL;
}
- rk808->i2c = client;
+ rk808->dev = &client->dev;
i2c_set_clientdata(client, rk808);
rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 9af1f3105f80..a89ddd9ba68e 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -787,7 +787,7 @@ enum {
};
struct rk808 {
- struct i2c_client *i2c;
+ struct device *dev;
struct regmap_irq_chip_data *irq_data;
struct regmap *regmap;
long variant;
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 07/13] mfd: rk808: split into core and i2c
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Split rk808 into a core and an i2c part in preperation for
SPI support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/clk/Kconfig | 2 +-
drivers/input/misc/Kconfig | 2 +-
drivers/mfd/Kconfig | 7 +-
drivers/mfd/Makefile | 3 +-
drivers/mfd/{rk808.c => rk8xx-core.c} | 210 ++++----------------------
drivers/mfd/rk8xx-i2c.c | 209 +++++++++++++++++++++++++
drivers/pinctrl/Kconfig | 2 +-
drivers/power/supply/Kconfig | 2 +-
drivers/regulator/Kconfig | 2 +-
drivers/rtc/Kconfig | 2 +-
include/linux/mfd/rk808.h | 6 +
sound/soc/codecs/Kconfig | 2 +-
12 files changed, 263 insertions(+), 186 deletions(-)
rename drivers/mfd/{rk808.c => rk8xx-core.c} (75%)
create mode 100644 drivers/mfd/rk8xx-i2c.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index d79905f3e174..8448d616b9aa 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -83,7 +83,7 @@ config COMMON_CLK_MAX9485
config COMMON_CLK_RK808
tristate "Clock driver for RK805/RK808/RK809/RK817/RK818"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
This driver supports RK805, RK809 and RK817, RK808 and RK818 crystal oscillator clock.
These multi-function devices have two fixed-rate oscillators, clocked at 32KHz each.
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index 9f088900f863..1899afeaec47 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -588,7 +588,7 @@ config INPUT_PWM_VIBRA
config INPUT_RK805_PWRKEY
tristate "Rockchip RK805 PMIC power key support"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Select this option to enable power key driver for RK805.
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8b93856de432..8e3de443cc3d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1201,12 +1201,17 @@ config MFD_RC5T583
Additional drivers must be enabled in order to use the
different functionality of the device.
-config MFD_RK808
+config MFD_RK8XX
+ bool
+ select MFD_CORE
+
+config MFD_RK8XX_I2C
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
depends on I2C && OF
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
+ select MFD_RK8XX
help
If you say yes here you get support for the RK805, RK808, RK809,
RK817 and RK818 Power Management chips.
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 7ed3ef4a698c..edf84e870f98 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -223,7 +223,8 @@ obj-$(CONFIG_MFD_PALMAS) += palmas.o
obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
obj-$(CONFIG_MFD_NTXEC) += ntxec.o
obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
-obj-$(CONFIG_MFD_RK808) += rk808.o
+obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
+obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
obj-$(CONFIG_MFD_SYSCON) += syscon.o
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk8xx-core.c
similarity index 75%
rename from drivers/mfd/rk808.c
rename to drivers/mfd/rk8xx-core.c
index b154ca96d812..098506972710 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk8xx-core.c
@@ -3,16 +3,9 @@
* MFD core driver for Rockchip RK808/RK818
*
* Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
- *
- * Author: Chris Zhong <zyw@rock-chips.com>
- * Author: Zhang Qing <zhangqing@rock-chips.com>
- *
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
- *
- * Author: Wadim Egorov <w.egorov@phytec.de>
*/
-#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/mfd/rk808.h>
#include <linux/mfd/core.h>
@@ -27,92 +20,6 @@ struct rk808_reg_data {
int value;
};
-static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
-{
- /*
- * Notes:
- * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
- * we don't use that feature. It's better to cache.
- * - It's unlikely we care that RK808_DEVCTRL_REG is volatile since
- * bits are cleared in case when we shutoff anyway, but better safe.
- */
-
- switch (reg) {
- case RK808_SECONDS_REG ... RK808_WEEKS_REG:
- case RK808_RTC_STATUS_REG:
- case RK808_VB_MON_REG:
- case RK808_THERMAL_REG:
- case RK808_DCDC_UV_STS_REG:
- case RK808_LDO_UV_STS_REG:
- case RK808_DCDC_PG_REG:
- case RK808_LDO_PG_REG:
- case RK808_DEVCTRL_REG:
- case RK808_INT_STS_REG1:
- case RK808_INT_STS_REG2:
- return true;
- }
-
- return false;
-}
-
-static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
-{
- /*
- * Notes:
- * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
- * we don't use that feature. It's better to cache.
- */
-
- switch (reg) {
- case RK817_SECONDS_REG ... RK817_WEEKS_REG:
- case RK817_RTC_STATUS_REG:
- case RK817_CODEC_DTOP_LPT_SRST:
- case RK817_GAS_GAUGE_ADC_CONFIG0 ... RK817_GAS_GAUGE_CUR_ADC_K0:
- case RK817_PMIC_CHRG_STS:
- case RK817_PMIC_CHRG_OUT:
- case RK817_PMIC_CHRG_IN:
- case RK817_INT_STS_REG0:
- case RK817_INT_STS_REG1:
- case RK817_INT_STS_REG2:
- case RK817_SYS_STS:
- return true;
- }
-
- return false;
-}
-
-static const struct regmap_config rk818_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK818_USB_CTRL_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk805_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK805_OFF_SOURCE_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk808_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK808_IO_POL_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk817_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK817_GPIO_INT_CFG,
- .cache_type = REGCACHE_NONE,
- .volatile_reg = rk817_is_volatile_reg,
-};
-
static const struct resource rtc_resources[] = {
DEFINE_RES_IRQ(RK808_IRQ_RTC_ALARM),
};
@@ -598,9 +505,9 @@ static int rk808_restart(struct sys_off_data *data)
return NOTIFY_DONE;
}
-static void rk8xx_shutdown(struct i2c_client *client)
+void rk8xx_shutdown(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(client);
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret;
switch (rk808->variant) {
@@ -621,62 +528,31 @@ static void rk8xx_shutdown(struct i2c_client *client)
return;
}
if (ret)
- dev_warn(&client->dev,
+ dev_warn(dev,
"Cannot switch to power down function\n");
}
+EXPORT_SYMBOL_GPL(rk8xx_shutdown);
-static const struct of_device_id rk808_of_match[] = {
- { .compatible = "rockchip,rk805" },
- { .compatible = "rockchip,rk808" },
- { .compatible = "rockchip,rk809" },
- { .compatible = "rockchip,rk817" },
- { .compatible = "rockchip,rk818" },
- { },
-};
-MODULE_DEVICE_TABLE(of, rk808_of_match);
-
-static int rk808_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap *regmap)
{
- struct device_node *np = client->dev.of_node;
struct rk808 *rk808;
const struct rk808_reg_data *pre_init_reg;
const struct mfd_cell *cells;
int nr_pre_init_regs;
int nr_cells;
- int msb, lsb;
- unsigned char pmic_id_msb, pmic_id_lsb;
int ret;
int i;
- rk808 = devm_kzalloc(&client->dev, sizeof(*rk808), GFP_KERNEL);
+ rk808 = devm_kzalloc(dev, sizeof(*rk808), GFP_KERNEL);
if (!rk808)
return -ENOMEM;
-
- if (of_device_is_compatible(np, "rockchip,rk817") ||
- of_device_is_compatible(np, "rockchip,rk809")) {
- pmic_id_msb = RK817_ID_MSB;
- pmic_id_lsb = RK817_ID_LSB;
- } else {
- pmic_id_msb = RK808_ID_MSB;
- pmic_id_lsb = RK808_ID_LSB;
- }
-
- /* Read chip variant */
- msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
- if (msb < 0)
- return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
-
- lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
- if (lsb < 0)
- return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
-
- rk808->variant = ((msb << 8) | lsb) & RK8XX_ID_MSK;
- dev_info(&client->dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
+ rk808->dev = dev;
+ rk808->variant = variant;
+ rk808->regmap = regmap;
+ dev_set_drvdata(dev, rk808);
switch (rk808->variant) {
case RK805_ID:
- rk808->regmap_cfg = &rk805_regmap_config;
rk808->regmap_irq_chip = &rk805_irq_chip;
pre_init_reg = rk805_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk805_pre_init_reg);
@@ -684,7 +560,6 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk805s);
break;
case RK808_ID:
- rk808->regmap_cfg = &rk808_regmap_config;
rk808->regmap_irq_chip = &rk808_irq_chip;
pre_init_reg = rk808_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg);
@@ -692,7 +567,6 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk808s);
break;
case RK818_ID:
- rk808->regmap_cfg = &rk818_regmap_config;
rk808->regmap_irq_chip = &rk818_irq_chip;
pre_init_reg = rk818_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg);
@@ -701,7 +575,6 @@ static int rk808_probe(struct i2c_client *client,
break;
case RK809_ID:
case RK817_ID:
- rk808->regmap_cfg = &rk817_regmap_config;
rk808->regmap_irq_chip = &rk817_irq_chip;
pre_init_reg = rk817_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk817_pre_init_reg);
@@ -709,27 +582,20 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk817s);
break;
default:
- dev_err(&client->dev, "Unsupported RK8XX ID %lu\n",
- rk808->variant);
+ dev_err(dev, "Unsupported RK8XX ID %lu\n", rk808->variant);
return -EINVAL;
}
- rk808->dev = &client->dev;
- i2c_set_clientdata(client, rk808);
-
- rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
- if (IS_ERR(rk808->regmap))
- return dev_err_probe(&client->dev, PTR_ERR(rk808->regmap),
- "regmap initialization failed\n");
+ dev_info(dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
- if (!client->irq)
- return dev_err_probe(&client->dev, -EINVAL, "No interrupt support, no core IRQ\n");
+ if (!irq)
+ return dev_err_probe(dev, -EINVAL, "No interrupt support, no core IRQ\n");
- ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
+ ret = devm_regmap_add_irq_chip(dev, rk808->regmap, irq,
IRQF_ONESHOT, -1,
rk808->regmap_irq_chip, &rk808->irq_data);
if (ret)
- return dev_err_probe(&client->dev, ret, "Failed to add irq_chip\n");
+ return dev_err_probe(dev, ret, "Failed to add irq_chip\n");
for (i = 0; i < nr_pre_init_regs; i++) {
ret = regmap_update_bits(rk808->regmap,
@@ -737,45 +603,46 @@ static int rk808_probe(struct i2c_client *client,
pre_init_reg[i].mask,
pre_init_reg[i].value);
if (ret)
- return dev_err_probe(&client->dev, ret, "0x%x write err\n",
+ return dev_err_probe(dev, ret, "0x%x write err\n",
pre_init_reg[i].addr);
}
- ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
+ ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
if (ret)
- return dev_err_probe(&client->dev, ret, "failed to add MFD devices\n");
+ return dev_err_probe(dev, ret, "failed to add MFD devices\n");
- if (of_property_read_bool(np, "rockchip,system-power-controller")) {
- ret = devm_register_sys_off_handler(&client->dev,
+ if (device_property_read_bool(dev, "rockchip,system-power-controller")) {
+ ret = devm_register_sys_off_handler(dev,
SYS_OFF_MODE_POWER_OFF_PREPARE, SYS_OFF_PRIO_HIGH,
&rk808_power_off, rk808);
if (ret)
- return dev_err_probe(&client->dev, ret,
+ return dev_err_probe(dev, ret,
"failed to register poweroff handler\n");
switch (rk808->variant) {
case RK809_ID:
case RK817_ID:
- ret = devm_register_sys_off_handler(&client->dev,
+ ret = devm_register_sys_off_handler(dev,
SYS_OFF_MODE_RESTART, SYS_OFF_PRIO_HIGH,
&rk808_restart, rk808);
if (ret)
- dev_warn(&client->dev, "failed to register rst handler, %d\n", ret);
+ dev_warn(dev, "failed to register rst handler, %d\n", ret);
break;
default:
- dev_dbg(&client->dev, "pmic controlled board reset not supported\n");
+ dev_dbg(dev, "pmic controlled board reset not supported\n");
break;
}
}
return 0;
}
+EXPORT_SYMBOL_GPL(rk8xx_probe);
-static int __maybe_unused rk8xx_suspend(struct device *dev)
+int rk8xx_suspend(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(to_i2c_client(dev));
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret = 0;
switch (rk808->variant) {
@@ -798,10 +665,11 @@ static int __maybe_unused rk8xx_suspend(struct device *dev)
return ret;
}
+EXPORT_SYMBOL_GPL(rk8xx_suspend);
-static int __maybe_unused rk8xx_resume(struct device *dev)
+int rk8xx_resume(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(to_i2c_client(dev));
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret = 0;
switch (rk808->variant) {
@@ -818,22 +686,10 @@ static int __maybe_unused rk8xx_resume(struct device *dev)
return ret;
}
-static SIMPLE_DEV_PM_OPS(rk8xx_pm_ops, rk8xx_suspend, rk8xx_resume);
-
-static struct i2c_driver rk808_i2c_driver = {
- .driver = {
- .name = "rk808",
- .of_match_table = rk808_of_match,
- .pm = &rk8xx_pm_ops,
- },
- .probe = rk808_probe,
- .shutdown = rk8xx_shutdown,
-};
-
-module_i2c_driver(rk808_i2c_driver);
+EXPORT_SYMBOL_GPL(rk8xx_resume);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
-MODULE_DESCRIPTION("RK808/RK818 PMIC driver");
+MODULE_DESCRIPTION("RK8xx PMIC core");
diff --git a/drivers/mfd/rk8xx-i2c.c b/drivers/mfd/rk8xx-i2c.c
new file mode 100644
index 000000000000..7babb0e1e64c
--- /dev/null
+++ b/drivers/mfd/rk8xx-i2c.c
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Rockchip RK808/RK818 Core (I2C) driver
+ *
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ *
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ * Author: Zhang Qing <zhangqing@rock-chips.com>
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ */
+
+#include <linux/i2c.h>
+#include <linux/mfd/rk808.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+
+static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Notes:
+ * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ * - It's unlikely we care that RK808_DEVCTRL_REG is volatile since
+ * bits are cleared in case when we shutoff anyway, but better safe.
+ */
+
+ switch (reg) {
+ case RK808_SECONDS_REG ... RK808_WEEKS_REG:
+ case RK808_RTC_STATUS_REG:
+ case RK808_VB_MON_REG:
+ case RK808_THERMAL_REG:
+ case RK808_DCDC_UV_STS_REG:
+ case RK808_LDO_UV_STS_REG:
+ case RK808_DCDC_PG_REG:
+ case RK808_LDO_PG_REG:
+ case RK808_DEVCTRL_REG:
+ case RK808_INT_STS_REG1:
+ case RK808_INT_STS_REG2:
+ return true;
+ }
+
+ return false;
+}
+
+static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Notes:
+ * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ */
+
+ switch (reg) {
+ case RK817_SECONDS_REG ... RK817_WEEKS_REG:
+ case RK817_RTC_STATUS_REG:
+ case RK817_CODEC_DTOP_LPT_SRST:
+ case RK817_GAS_GAUGE_ADC_CONFIG0 ... RK817_GAS_GAUGE_CUR_ADC_K0:
+ case RK817_PMIC_CHRG_STS:
+ case RK817_PMIC_CHRG_OUT:
+ case RK817_PMIC_CHRG_IN:
+ case RK817_INT_STS_REG0:
+ case RK817_INT_STS_REG1:
+ case RK817_INT_STS_REG2:
+ case RK817_SYS_STS:
+ return true;
+ }
+
+ return false;
+}
+
+
+static const struct regmap_config rk818_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK818_USB_CTRL_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk805_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK805_OFF_SOURCE_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk808_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK808_IO_POL_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk817_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK817_GPIO_INT_CFG,
+ .cache_type = REGCACHE_NONE,
+ .volatile_reg = rk817_is_volatile_reg,
+};
+
+static int rk8xx_i2c_get_variant(struct i2c_client *client)
+{
+ u8 pmic_id_msb, pmic_id_lsb;
+ int msb, lsb;
+
+ if (of_device_is_compatible(client->dev.of_node, "rockchip,rk817") ||
+ of_device_is_compatible(client->dev.of_node, "rockchip,rk809")) {
+ pmic_id_msb = RK817_ID_MSB;
+ pmic_id_lsb = RK817_ID_LSB;
+ } else {
+ pmic_id_msb = RK808_ID_MSB;
+ pmic_id_lsb = RK808_ID_LSB;
+ }
+
+ /* Read chip variant */
+ msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
+ if (msb < 0)
+ return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
+
+ lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
+ if (lsb < 0)
+ return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
+
+ return ((msb << 8) | lsb) & RK8XX_ID_MSK;
+}
+
+static int rk8xx_i2c_probe(struct i2c_client *client)
+{
+ const struct regmap_config *regmap_cfg;
+ struct regmap *regmap;
+ int variant;
+
+ variant = rk8xx_i2c_get_variant(client);
+ if (variant < 0)
+ return variant;
+
+ switch (variant) {
+ case RK805_ID:
+ regmap_cfg = &rk805_regmap_config;
+ break;
+ case RK808_ID:
+ regmap_cfg = &rk808_regmap_config;
+ break;
+ case RK818_ID:
+ regmap_cfg = &rk818_regmap_config;
+ break;
+ case RK809_ID:
+ case RK817_ID:
+ regmap_cfg = &rk817_regmap_config;
+ break;
+ default:
+ return dev_err_probe(&client->dev, -EINVAL, "Unsupported RK8XX ID %x\n", variant);
+ }
+
+ regmap = devm_regmap_init_i2c(client, regmap_cfg);
+ if (IS_ERR(regmap))
+ return dev_err_probe(&client->dev, PTR_ERR(regmap),
+ "regmap initialization failed\n");
+
+ return rk8xx_probe(&client->dev, variant, client->irq, regmap);
+}
+
+static void rk8xx_i2c_shutdown(struct i2c_client *client)
+{
+ rk8xx_shutdown(&client->dev);
+}
+
+static int __maybe_unused rk8xx_i2c_suspend(struct device *dev)
+{
+ return rk8xx_suspend(dev);
+}
+
+static int __maybe_unused rk8xx_i2c_resume(struct device *dev)
+{
+ return rk8xx_resume(dev);
+}
+static SIMPLE_DEV_PM_OPS(rk8xx_i2c_pm_ops, rk8xx_i2c_suspend, rk8xx_i2c_resume);
+
+static const struct of_device_id rk8xx_i2c_of_match[] = {
+ { .compatible = "rockchip,rk805" },
+ { .compatible = "rockchip,rk808" },
+ { .compatible = "rockchip,rk809" },
+ { .compatible = "rockchip,rk817" },
+ { .compatible = "rockchip,rk818" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, rk8xx_i2c_of_match);
+
+static struct i2c_driver rk8xx_i2c_driver = {
+ .driver = {
+ .name = "rk8xx-i2c",
+ .of_match_table = rk8xx_i2c_of_match,
+ .pm = &rk8xx_i2c_pm_ops,
+ },
+ .probe_new = rk8xx_i2c_probe,
+ .shutdown = rk8xx_i2c_shutdown,
+};
+module_i2c_driver(rk8xx_i2c_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
+MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
+MODULE_DESCRIPTION("RK8xx I2C PMIC driver");
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index f71fefff400f..3618660b6a5c 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -396,7 +396,7 @@ config PINCTRL_PISTACHIO
config PINCTRL_RK805
tristate "Pinctrl and GPIO driver for RK805 PMIC"
- depends on MFD_RK808
+ depends on MFD_RK8XX
select GPIOLIB
select PINMUX
select GENERIC_PINCONF
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 0bbfe6a7ce4d..306a9b1f897e 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -725,7 +725,7 @@ config CHARGER_BQ256XX
config CHARGER_RK817
tristate "Rockchip RK817 PMIC Battery Charger"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Say Y to include support for Rockchip RK817 Battery Charger.
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 070e4403c6c2..d5eb240a1bb1 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1039,7 +1039,7 @@ config REGULATOR_RC5T583
config REGULATOR_RK808
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power regulators"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Select this option to enable the power regulator of ROCKCHIP
PMIC RK805,RK809&RK817,RK808 and RK818.
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index bb63edb507da..09f59059a60f 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -395,7 +395,7 @@ config RTC_DRV_NCT3018Y
config RTC_DRV_RK808
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 RTC"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
If you say yes here you will get support for the
RTC of RK805, RK809 and RK817, RK808 and RK818 PMIC.
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index a89ddd9ba68e..4183427a80fe 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -794,4 +794,10 @@ struct rk808 {
const struct regmap_config *regmap_cfg;
const struct regmap_irq_chip *regmap_irq_chip;
};
+
+void rk8xx_shutdown(struct device *dev);
+int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap *regmap);
+int rk8xx_suspend(struct device *dev);
+int rk8xx_resume(struct device *dev);
+
#endif /* __LINUX_REGULATOR_RK808_H */
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index e3b90c425faf..fec157721703 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -1210,7 +1210,7 @@ config SND_SOC_RK3328
config SND_SOC_RK817
tristate "Rockchip RK817 audio CODEC"
- depends on MFD_RK808 || COMPILE_TEST
+ depends on MFD_RK8XX || COMPILE_TEST
config SND_SOC_RL6231
tristate
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 07/13] mfd: rk808: split into core and i2c
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Split rk808 into a core and an i2c part in preperation for
SPI support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/clk/Kconfig | 2 +-
drivers/input/misc/Kconfig | 2 +-
drivers/mfd/Kconfig | 7 +-
drivers/mfd/Makefile | 3 +-
drivers/mfd/{rk808.c => rk8xx-core.c} | 210 ++++----------------------
drivers/mfd/rk8xx-i2c.c | 209 +++++++++++++++++++++++++
drivers/pinctrl/Kconfig | 2 +-
drivers/power/supply/Kconfig | 2 +-
drivers/regulator/Kconfig | 2 +-
drivers/rtc/Kconfig | 2 +-
include/linux/mfd/rk808.h | 6 +
sound/soc/codecs/Kconfig | 2 +-
12 files changed, 263 insertions(+), 186 deletions(-)
rename drivers/mfd/{rk808.c => rk8xx-core.c} (75%)
create mode 100644 drivers/mfd/rk8xx-i2c.c
diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
index d79905f3e174..8448d616b9aa 100644
--- a/drivers/clk/Kconfig
+++ b/drivers/clk/Kconfig
@@ -83,7 +83,7 @@ config COMMON_CLK_MAX9485
config COMMON_CLK_RK808
tristate "Clock driver for RK805/RK808/RK809/RK817/RK818"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
This driver supports RK805, RK809 and RK817, RK808 and RK818 crystal oscillator clock.
These multi-function devices have two fixed-rate oscillators, clocked at 32KHz each.
diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index 9f088900f863..1899afeaec47 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -588,7 +588,7 @@ config INPUT_PWM_VIBRA
config INPUT_RK805_PWRKEY
tristate "Rockchip RK805 PMIC power key support"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Select this option to enable power key driver for RK805.
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8b93856de432..8e3de443cc3d 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1201,12 +1201,17 @@ config MFD_RC5T583
Additional drivers must be enabled in order to use the
different functionality of the device.
-config MFD_RK808
+config MFD_RK8XX
+ bool
+ select MFD_CORE
+
+config MFD_RK8XX_I2C
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
depends on I2C && OF
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
+ select MFD_RK8XX
help
If you say yes here you get support for the RK805, RK808, RK809,
RK817 and RK818 Power Management chips.
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 7ed3ef4a698c..edf84e870f98 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -223,7 +223,8 @@ obj-$(CONFIG_MFD_PALMAS) += palmas.o
obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
obj-$(CONFIG_MFD_NTXEC) += ntxec.o
obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
-obj-$(CONFIG_MFD_RK808) += rk808.o
+obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
+obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
obj-$(CONFIG_MFD_SYSCON) += syscon.o
diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk8xx-core.c
similarity index 75%
rename from drivers/mfd/rk808.c
rename to drivers/mfd/rk8xx-core.c
index b154ca96d812..098506972710 100644
--- a/drivers/mfd/rk808.c
+++ b/drivers/mfd/rk8xx-core.c
@@ -3,16 +3,9 @@
* MFD core driver for Rockchip RK808/RK818
*
* Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
- *
- * Author: Chris Zhong <zyw@rock-chips.com>
- * Author: Zhang Qing <zhangqing@rock-chips.com>
- *
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
- *
- * Author: Wadim Egorov <w.egorov@phytec.de>
*/
-#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/mfd/rk808.h>
#include <linux/mfd/core.h>
@@ -27,92 +20,6 @@ struct rk808_reg_data {
int value;
};
-static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
-{
- /*
- * Notes:
- * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
- * we don't use that feature. It's better to cache.
- * - It's unlikely we care that RK808_DEVCTRL_REG is volatile since
- * bits are cleared in case when we shutoff anyway, but better safe.
- */
-
- switch (reg) {
- case RK808_SECONDS_REG ... RK808_WEEKS_REG:
- case RK808_RTC_STATUS_REG:
- case RK808_VB_MON_REG:
- case RK808_THERMAL_REG:
- case RK808_DCDC_UV_STS_REG:
- case RK808_LDO_UV_STS_REG:
- case RK808_DCDC_PG_REG:
- case RK808_LDO_PG_REG:
- case RK808_DEVCTRL_REG:
- case RK808_INT_STS_REG1:
- case RK808_INT_STS_REG2:
- return true;
- }
-
- return false;
-}
-
-static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
-{
- /*
- * Notes:
- * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
- * we don't use that feature. It's better to cache.
- */
-
- switch (reg) {
- case RK817_SECONDS_REG ... RK817_WEEKS_REG:
- case RK817_RTC_STATUS_REG:
- case RK817_CODEC_DTOP_LPT_SRST:
- case RK817_GAS_GAUGE_ADC_CONFIG0 ... RK817_GAS_GAUGE_CUR_ADC_K0:
- case RK817_PMIC_CHRG_STS:
- case RK817_PMIC_CHRG_OUT:
- case RK817_PMIC_CHRG_IN:
- case RK817_INT_STS_REG0:
- case RK817_INT_STS_REG1:
- case RK817_INT_STS_REG2:
- case RK817_SYS_STS:
- return true;
- }
-
- return false;
-}
-
-static const struct regmap_config rk818_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK818_USB_CTRL_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk805_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK805_OFF_SOURCE_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk808_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK808_IO_POL_REG,
- .cache_type = REGCACHE_RBTREE,
- .volatile_reg = rk808_is_volatile_reg,
-};
-
-static const struct regmap_config rk817_regmap_config = {
- .reg_bits = 8,
- .val_bits = 8,
- .max_register = RK817_GPIO_INT_CFG,
- .cache_type = REGCACHE_NONE,
- .volatile_reg = rk817_is_volatile_reg,
-};
-
static const struct resource rtc_resources[] = {
DEFINE_RES_IRQ(RK808_IRQ_RTC_ALARM),
};
@@ -598,9 +505,9 @@ static int rk808_restart(struct sys_off_data *data)
return NOTIFY_DONE;
}
-static void rk8xx_shutdown(struct i2c_client *client)
+void rk8xx_shutdown(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(client);
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret;
switch (rk808->variant) {
@@ -621,62 +528,31 @@ static void rk8xx_shutdown(struct i2c_client *client)
return;
}
if (ret)
- dev_warn(&client->dev,
+ dev_warn(dev,
"Cannot switch to power down function\n");
}
+EXPORT_SYMBOL_GPL(rk8xx_shutdown);
-static const struct of_device_id rk808_of_match[] = {
- { .compatible = "rockchip,rk805" },
- { .compatible = "rockchip,rk808" },
- { .compatible = "rockchip,rk809" },
- { .compatible = "rockchip,rk817" },
- { .compatible = "rockchip,rk818" },
- { },
-};
-MODULE_DEVICE_TABLE(of, rk808_of_match);
-
-static int rk808_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap *regmap)
{
- struct device_node *np = client->dev.of_node;
struct rk808 *rk808;
const struct rk808_reg_data *pre_init_reg;
const struct mfd_cell *cells;
int nr_pre_init_regs;
int nr_cells;
- int msb, lsb;
- unsigned char pmic_id_msb, pmic_id_lsb;
int ret;
int i;
- rk808 = devm_kzalloc(&client->dev, sizeof(*rk808), GFP_KERNEL);
+ rk808 = devm_kzalloc(dev, sizeof(*rk808), GFP_KERNEL);
if (!rk808)
return -ENOMEM;
-
- if (of_device_is_compatible(np, "rockchip,rk817") ||
- of_device_is_compatible(np, "rockchip,rk809")) {
- pmic_id_msb = RK817_ID_MSB;
- pmic_id_lsb = RK817_ID_LSB;
- } else {
- pmic_id_msb = RK808_ID_MSB;
- pmic_id_lsb = RK808_ID_LSB;
- }
-
- /* Read chip variant */
- msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
- if (msb < 0)
- return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
-
- lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
- if (lsb < 0)
- return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
-
- rk808->variant = ((msb << 8) | lsb) & RK8XX_ID_MSK;
- dev_info(&client->dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
+ rk808->dev = dev;
+ rk808->variant = variant;
+ rk808->regmap = regmap;
+ dev_set_drvdata(dev, rk808);
switch (rk808->variant) {
case RK805_ID:
- rk808->regmap_cfg = &rk805_regmap_config;
rk808->regmap_irq_chip = &rk805_irq_chip;
pre_init_reg = rk805_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk805_pre_init_reg);
@@ -684,7 +560,6 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk805s);
break;
case RK808_ID:
- rk808->regmap_cfg = &rk808_regmap_config;
rk808->regmap_irq_chip = &rk808_irq_chip;
pre_init_reg = rk808_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk808_pre_init_reg);
@@ -692,7 +567,6 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk808s);
break;
case RK818_ID:
- rk808->regmap_cfg = &rk818_regmap_config;
rk808->regmap_irq_chip = &rk818_irq_chip;
pre_init_reg = rk818_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk818_pre_init_reg);
@@ -701,7 +575,6 @@ static int rk808_probe(struct i2c_client *client,
break;
case RK809_ID:
case RK817_ID:
- rk808->regmap_cfg = &rk817_regmap_config;
rk808->regmap_irq_chip = &rk817_irq_chip;
pre_init_reg = rk817_pre_init_reg;
nr_pre_init_regs = ARRAY_SIZE(rk817_pre_init_reg);
@@ -709,27 +582,20 @@ static int rk808_probe(struct i2c_client *client,
nr_cells = ARRAY_SIZE(rk817s);
break;
default:
- dev_err(&client->dev, "Unsupported RK8XX ID %lu\n",
- rk808->variant);
+ dev_err(dev, "Unsupported RK8XX ID %lu\n", rk808->variant);
return -EINVAL;
}
- rk808->dev = &client->dev;
- i2c_set_clientdata(client, rk808);
-
- rk808->regmap = devm_regmap_init_i2c(client, rk808->regmap_cfg);
- if (IS_ERR(rk808->regmap))
- return dev_err_probe(&client->dev, PTR_ERR(rk808->regmap),
- "regmap initialization failed\n");
+ dev_info(dev, "chip id: 0x%x\n", (unsigned int)rk808->variant);
- if (!client->irq)
- return dev_err_probe(&client->dev, -EINVAL, "No interrupt support, no core IRQ\n");
+ if (!irq)
+ return dev_err_probe(dev, -EINVAL, "No interrupt support, no core IRQ\n");
- ret = devm_regmap_add_irq_chip(&client->dev, rk808->regmap, client->irq,
+ ret = devm_regmap_add_irq_chip(dev, rk808->regmap, irq,
IRQF_ONESHOT, -1,
rk808->regmap_irq_chip, &rk808->irq_data);
if (ret)
- return dev_err_probe(&client->dev, ret, "Failed to add irq_chip\n");
+ return dev_err_probe(dev, ret, "Failed to add irq_chip\n");
for (i = 0; i < nr_pre_init_regs; i++) {
ret = regmap_update_bits(rk808->regmap,
@@ -737,45 +603,46 @@ static int rk808_probe(struct i2c_client *client,
pre_init_reg[i].mask,
pre_init_reg[i].value);
if (ret)
- return dev_err_probe(&client->dev, ret, "0x%x write err\n",
+ return dev_err_probe(dev, ret, "0x%x write err\n",
pre_init_reg[i].addr);
}
- ret = devm_mfd_add_devices(&client->dev, PLATFORM_DEVID_NONE,
+ ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
if (ret)
- return dev_err_probe(&client->dev, ret, "failed to add MFD devices\n");
+ return dev_err_probe(dev, ret, "failed to add MFD devices\n");
- if (of_property_read_bool(np, "rockchip,system-power-controller")) {
- ret = devm_register_sys_off_handler(&client->dev,
+ if (device_property_read_bool(dev, "rockchip,system-power-controller")) {
+ ret = devm_register_sys_off_handler(dev,
SYS_OFF_MODE_POWER_OFF_PREPARE, SYS_OFF_PRIO_HIGH,
&rk808_power_off, rk808);
if (ret)
- return dev_err_probe(&client->dev, ret,
+ return dev_err_probe(dev, ret,
"failed to register poweroff handler\n");
switch (rk808->variant) {
case RK809_ID:
case RK817_ID:
- ret = devm_register_sys_off_handler(&client->dev,
+ ret = devm_register_sys_off_handler(dev,
SYS_OFF_MODE_RESTART, SYS_OFF_PRIO_HIGH,
&rk808_restart, rk808);
if (ret)
- dev_warn(&client->dev, "failed to register rst handler, %d\n", ret);
+ dev_warn(dev, "failed to register rst handler, %d\n", ret);
break;
default:
- dev_dbg(&client->dev, "pmic controlled board reset not supported\n");
+ dev_dbg(dev, "pmic controlled board reset not supported\n");
break;
}
}
return 0;
}
+EXPORT_SYMBOL_GPL(rk8xx_probe);
-static int __maybe_unused rk8xx_suspend(struct device *dev)
+int rk8xx_suspend(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(to_i2c_client(dev));
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret = 0;
switch (rk808->variant) {
@@ -798,10 +665,11 @@ static int __maybe_unused rk8xx_suspend(struct device *dev)
return ret;
}
+EXPORT_SYMBOL_GPL(rk8xx_suspend);
-static int __maybe_unused rk8xx_resume(struct device *dev)
+int rk8xx_resume(struct device *dev)
{
- struct rk808 *rk808 = i2c_get_clientdata(to_i2c_client(dev));
+ struct rk808 *rk808 = dev_get_drvdata(dev);
int ret = 0;
switch (rk808->variant) {
@@ -818,22 +686,10 @@ static int __maybe_unused rk8xx_resume(struct device *dev)
return ret;
}
-static SIMPLE_DEV_PM_OPS(rk8xx_pm_ops, rk8xx_suspend, rk8xx_resume);
-
-static struct i2c_driver rk808_i2c_driver = {
- .driver = {
- .name = "rk808",
- .of_match_table = rk808_of_match,
- .pm = &rk8xx_pm_ops,
- },
- .probe = rk808_probe,
- .shutdown = rk8xx_shutdown,
-};
-
-module_i2c_driver(rk808_i2c_driver);
+EXPORT_SYMBOL_GPL(rk8xx_resume);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
-MODULE_DESCRIPTION("RK808/RK818 PMIC driver");
+MODULE_DESCRIPTION("RK8xx PMIC core");
diff --git a/drivers/mfd/rk8xx-i2c.c b/drivers/mfd/rk8xx-i2c.c
new file mode 100644
index 000000000000..7babb0e1e64c
--- /dev/null
+++ b/drivers/mfd/rk8xx-i2c.c
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Rockchip RK808/RK818 Core (I2C) driver
+ *
+ * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (C) 2016 PHYTEC Messtechnik GmbH
+ *
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ * Author: Zhang Qing <zhangqing@rock-chips.com>
+ * Author: Wadim Egorov <w.egorov@phytec.de>
+ */
+
+#include <linux/i2c.h>
+#include <linux/mfd/rk808.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+
+static bool rk808_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Notes:
+ * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ * - It's unlikely we care that RK808_DEVCTRL_REG is volatile since
+ * bits are cleared in case when we shutoff anyway, but better safe.
+ */
+
+ switch (reg) {
+ case RK808_SECONDS_REG ... RK808_WEEKS_REG:
+ case RK808_RTC_STATUS_REG:
+ case RK808_VB_MON_REG:
+ case RK808_THERMAL_REG:
+ case RK808_DCDC_UV_STS_REG:
+ case RK808_LDO_UV_STS_REG:
+ case RK808_DCDC_PG_REG:
+ case RK808_LDO_PG_REG:
+ case RK808_DEVCTRL_REG:
+ case RK808_INT_STS_REG1:
+ case RK808_INT_STS_REG2:
+ return true;
+ }
+
+ return false;
+}
+
+static bool rk817_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+ /*
+ * Notes:
+ * - Technically the ROUND_30s bit makes RTC_CTRL_REG volatile, but
+ * we don't use that feature. It's better to cache.
+ */
+
+ switch (reg) {
+ case RK817_SECONDS_REG ... RK817_WEEKS_REG:
+ case RK817_RTC_STATUS_REG:
+ case RK817_CODEC_DTOP_LPT_SRST:
+ case RK817_GAS_GAUGE_ADC_CONFIG0 ... RK817_GAS_GAUGE_CUR_ADC_K0:
+ case RK817_PMIC_CHRG_STS:
+ case RK817_PMIC_CHRG_OUT:
+ case RK817_PMIC_CHRG_IN:
+ case RK817_INT_STS_REG0:
+ case RK817_INT_STS_REG1:
+ case RK817_INT_STS_REG2:
+ case RK817_SYS_STS:
+ return true;
+ }
+
+ return false;
+}
+
+
+static const struct regmap_config rk818_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK818_USB_CTRL_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk805_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK805_OFF_SOURCE_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk808_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK808_IO_POL_REG,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_reg = rk808_is_volatile_reg,
+};
+
+static const struct regmap_config rk817_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = RK817_GPIO_INT_CFG,
+ .cache_type = REGCACHE_NONE,
+ .volatile_reg = rk817_is_volatile_reg,
+};
+
+static int rk8xx_i2c_get_variant(struct i2c_client *client)
+{
+ u8 pmic_id_msb, pmic_id_lsb;
+ int msb, lsb;
+
+ if (of_device_is_compatible(client->dev.of_node, "rockchip,rk817") ||
+ of_device_is_compatible(client->dev.of_node, "rockchip,rk809")) {
+ pmic_id_msb = RK817_ID_MSB;
+ pmic_id_lsb = RK817_ID_LSB;
+ } else {
+ pmic_id_msb = RK808_ID_MSB;
+ pmic_id_lsb = RK808_ID_LSB;
+ }
+
+ /* Read chip variant */
+ msb = i2c_smbus_read_byte_data(client, pmic_id_msb);
+ if (msb < 0)
+ return dev_err_probe(&client->dev, msb, "failed to read the chip id MSB\n");
+
+ lsb = i2c_smbus_read_byte_data(client, pmic_id_lsb);
+ if (lsb < 0)
+ return dev_err_probe(&client->dev, lsb, "failed to read the chip id LSB\n");
+
+ return ((msb << 8) | lsb) & RK8XX_ID_MSK;
+}
+
+static int rk8xx_i2c_probe(struct i2c_client *client)
+{
+ const struct regmap_config *regmap_cfg;
+ struct regmap *regmap;
+ int variant;
+
+ variant = rk8xx_i2c_get_variant(client);
+ if (variant < 0)
+ return variant;
+
+ switch (variant) {
+ case RK805_ID:
+ regmap_cfg = &rk805_regmap_config;
+ break;
+ case RK808_ID:
+ regmap_cfg = &rk808_regmap_config;
+ break;
+ case RK818_ID:
+ regmap_cfg = &rk818_regmap_config;
+ break;
+ case RK809_ID:
+ case RK817_ID:
+ regmap_cfg = &rk817_regmap_config;
+ break;
+ default:
+ return dev_err_probe(&client->dev, -EINVAL, "Unsupported RK8XX ID %x\n", variant);
+ }
+
+ regmap = devm_regmap_init_i2c(client, regmap_cfg);
+ if (IS_ERR(regmap))
+ return dev_err_probe(&client->dev, PTR_ERR(regmap),
+ "regmap initialization failed\n");
+
+ return rk8xx_probe(&client->dev, variant, client->irq, regmap);
+}
+
+static void rk8xx_i2c_shutdown(struct i2c_client *client)
+{
+ rk8xx_shutdown(&client->dev);
+}
+
+static int __maybe_unused rk8xx_i2c_suspend(struct device *dev)
+{
+ return rk8xx_suspend(dev);
+}
+
+static int __maybe_unused rk8xx_i2c_resume(struct device *dev)
+{
+ return rk8xx_resume(dev);
+}
+static SIMPLE_DEV_PM_OPS(rk8xx_i2c_pm_ops, rk8xx_i2c_suspend, rk8xx_i2c_resume);
+
+static const struct of_device_id rk8xx_i2c_of_match[] = {
+ { .compatible = "rockchip,rk805" },
+ { .compatible = "rockchip,rk808" },
+ { .compatible = "rockchip,rk809" },
+ { .compatible = "rockchip,rk817" },
+ { .compatible = "rockchip,rk818" },
+ { },
+};
+MODULE_DEVICE_TABLE(of, rk8xx_i2c_of_match);
+
+static struct i2c_driver rk8xx_i2c_driver = {
+ .driver = {
+ .name = "rk8xx-i2c",
+ .of_match_table = rk8xx_i2c_of_match,
+ .pm = &rk8xx_i2c_pm_ops,
+ },
+ .probe_new = rk8xx_i2c_probe,
+ .shutdown = rk8xx_i2c_shutdown,
+};
+module_i2c_driver(rk8xx_i2c_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
+MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
+MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
+MODULE_DESCRIPTION("RK8xx I2C PMIC driver");
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index f71fefff400f..3618660b6a5c 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -396,7 +396,7 @@ config PINCTRL_PISTACHIO
config PINCTRL_RK805
tristate "Pinctrl and GPIO driver for RK805 PMIC"
- depends on MFD_RK808
+ depends on MFD_RK8XX
select GPIOLIB
select PINMUX
select GENERIC_PINCONF
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 0bbfe6a7ce4d..306a9b1f897e 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -725,7 +725,7 @@ config CHARGER_BQ256XX
config CHARGER_RK817
tristate "Rockchip RK817 PMIC Battery Charger"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Say Y to include support for Rockchip RK817 Battery Charger.
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 070e4403c6c2..d5eb240a1bb1 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1039,7 +1039,7 @@ config REGULATOR_RC5T583
config REGULATOR_RK808
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power regulators"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
Select this option to enable the power regulator of ROCKCHIP
PMIC RK805,RK809&RK817,RK808 and RK818.
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index bb63edb507da..09f59059a60f 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -395,7 +395,7 @@ config RTC_DRV_NCT3018Y
config RTC_DRV_RK808
tristate "Rockchip RK805/RK808/RK809/RK817/RK818 RTC"
- depends on MFD_RK808
+ depends on MFD_RK8XX
help
If you say yes here you will get support for the
RTC of RK805, RK809 and RK817, RK808 and RK818 PMIC.
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index a89ddd9ba68e..4183427a80fe 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -794,4 +794,10 @@ struct rk808 {
const struct regmap_config *regmap_cfg;
const struct regmap_irq_chip *regmap_irq_chip;
};
+
+void rk8xx_shutdown(struct device *dev);
+int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap *regmap);
+int rk8xx_suspend(struct device *dev);
+int rk8xx_resume(struct device *dev);
+
#endif /* __LINUX_REGULATOR_RK808_H */
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index e3b90c425faf..fec157721703 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -1210,7 +1210,7 @@ config SND_SOC_RK3328
config SND_SOC_RK817
tristate "Rockchip RK817 audio CODEC"
- depends on MFD_RK808 || COMPILE_TEST
+ depends on MFD_RK8XX || COMPILE_TEST
config SND_SOC_RL6231
tristate
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 08/13] dt-bindings: mfd: add rk806 binding
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Add DT binding document for Rockchip's RK806 PMIC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
.../bindings/mfd/rockchip,rk806.yaml | 405 ++++++++++++++++++
1 file changed, 405 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
diff --git a/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
new file mode 100644
index 000000000000..4e907dd1f7a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
@@ -0,0 +1,405 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RK806 Power Management Integrated Circuit
+
+maintainers:
+ - Sebastian Reichel <sebastian.reichel@collabora.com>
+
+description: |
+ Rockchip RK806 series PMIC. This device consists of an spi or
+ i2c controlled MFD that includes multiple switchable regulators.
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk806
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ vcc1-supply:
+ description:
+ The input supply for dcdc-reg1.
+
+ vcc2-supply:
+ description:
+ The input supply for dcdc-reg2.
+
+ vcc3-supply:
+ description:
+ The input supply for dcdc-reg3.
+
+ vcc4-supply:
+ description:
+ The input supply for dcdc-reg4.
+
+ vcc5-supply:
+ description:
+ The input supply for dcdc-reg5.
+
+ vcc6-supply:
+ description:
+ The input supply for dcdc-reg6.
+
+ vcc7-supply:
+ description:
+ The input supply for dcdc-reg7.
+
+ vcc8-supply:
+ description:
+ The input supply for dcdc-reg8.
+
+ vcc9-supply:
+ description:
+ The input supply for dcdc-reg9.
+
+ vcc10-supply:
+ description:
+ The input supply for dcdc-reg10.
+
+ vcc11-supply:
+ description:
+ The input supply for pldo-reg1, pldo-reg2 and pldo-reg3.
+
+ vcc12-supply:
+ description:
+ The input supply for pldo-reg4 and pldo-reg5.
+
+ vcc13-supply:
+ description:
+ The input supply for nldo-reg1, nldo-reg2 and nldo-reg3.
+
+ vcc14-supply:
+ description:
+ The input supply for nldo-reg4 and nldo-reg5.
+
+ vcca-supply:
+ description:
+ The input supply for pldo-reg6.
+
+ regulators:
+ type: object
+ patternProperties:
+ "^(dcdc-reg([1-9]|10)|pldo-reg[1-6]|nldo-reg[1-5])$":
+ type: object
+ $ref: /schemas/regulator/regulator.yaml#
+ unevaluatedProperties: false
+ additionalProperties: false
+
+patternProperties:
+ '-pins$':
+ type: object
+ $ref: /schemas/pinctrl/pinmux-node.yaml
+
+ properties:
+ function:
+ enum: [pin_fun0, pin_fun1, pin_fun2, pin_fun3, pin_fun4, pin_fun5]
+
+ pins:
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [gpio_pwrctrl1, gpio_pwrctrl2, gpio_pwrctrl3]
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/rockchip.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc5v0_sys>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_gpu_s0: dcdc-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_s0: dcdc-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_log_s0";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_vdenc_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu_mem_s0: dcdc-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_mem_s0: dcdc-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vdd_vdenc_mem_s0: dcdc-reg8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_vdenc_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd2_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v1_nldo_s3: dcdc-reg10 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1100000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "avcc_1v8_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd1_1v8_ddr_s3: pldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd1_1v8_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_1v8_s3: pldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_1v8_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vccio_sd_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ master_pldo6_s3: pldo-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "master_pldo6_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_0v75_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd2l_0v9_ddr_s3: nldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd2l_0v9_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ master_nldo3: nldo-reg3 {
+ regulator-name = "master_nldo3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "avdd_0v75_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdd_0v85_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+ };
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 08/13] dt-bindings: mfd: add rk806 binding
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Add DT binding document for Rockchip's RK806 PMIC.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
.../bindings/mfd/rockchip,rk806.yaml | 405 ++++++++++++++++++
1 file changed, 405 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
diff --git a/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
new file mode 100644
index 000000000000..4e907dd1f7a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
@@ -0,0 +1,405 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RK806 Power Management Integrated Circuit
+
+maintainers:
+ - Sebastian Reichel <sebastian.reichel@collabora.com>
+
+description: |
+ Rockchip RK806 series PMIC. This device consists of an spi or
+ i2c controlled MFD that includes multiple switchable regulators.
+
+properties:
+ compatible:
+ enum:
+ - rockchip,rk806
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+ vcc1-supply:
+ description:
+ The input supply for dcdc-reg1.
+
+ vcc2-supply:
+ description:
+ The input supply for dcdc-reg2.
+
+ vcc3-supply:
+ description:
+ The input supply for dcdc-reg3.
+
+ vcc4-supply:
+ description:
+ The input supply for dcdc-reg4.
+
+ vcc5-supply:
+ description:
+ The input supply for dcdc-reg5.
+
+ vcc6-supply:
+ description:
+ The input supply for dcdc-reg6.
+
+ vcc7-supply:
+ description:
+ The input supply for dcdc-reg7.
+
+ vcc8-supply:
+ description:
+ The input supply for dcdc-reg8.
+
+ vcc9-supply:
+ description:
+ The input supply for dcdc-reg9.
+
+ vcc10-supply:
+ description:
+ The input supply for dcdc-reg10.
+
+ vcc11-supply:
+ description:
+ The input supply for pldo-reg1, pldo-reg2 and pldo-reg3.
+
+ vcc12-supply:
+ description:
+ The input supply for pldo-reg4 and pldo-reg5.
+
+ vcc13-supply:
+ description:
+ The input supply for nldo-reg1, nldo-reg2 and nldo-reg3.
+
+ vcc14-supply:
+ description:
+ The input supply for nldo-reg4 and nldo-reg5.
+
+ vcca-supply:
+ description:
+ The input supply for pldo-reg6.
+
+ regulators:
+ type: object
+ patternProperties:
+ "^(dcdc-reg([1-9]|10)|pldo-reg[1-6]|nldo-reg[1-5])$":
+ type: object
+ $ref: /schemas/regulator/regulator.yaml#
+ unevaluatedProperties: false
+ additionalProperties: false
+
+patternProperties:
+ '-pins$':
+ type: object
+ $ref: /schemas/pinctrl/pinmux-node.yaml
+
+ properties:
+ function:
+ enum: [pin_fun0, pin_fun1, pin_fun2, pin_fun3, pin_fun4, pin_fun5]
+
+ pins:
+ $ref: "/schemas/types.yaml#/definitions/string"
+ enum: [gpio_pwrctrl1, gpio_pwrctrl2, gpio_pwrctrl3]
+
+allOf:
+ - $ref: /schemas/spi/spi-peripheral-props.yaml
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/pinctrl/rockchip.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/gpio/gpio.h>
+ spi {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc5v0_sys>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ regulators {
+ vdd_gpu_s0: dcdc-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_s0: dcdc-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_log_s0";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_vdenc_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_gpu_mem_s0: dcdc-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_mem_s0: dcdc-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vdd_vdenc_mem_s0: dcdc-reg8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_vdenc_mem_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd2_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_1v1_nldo_s3: dcdc-reg10 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1100000>;
+ };
+ };
+
+ avcc_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "avcc_1v8_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd1_1v8_ddr_s3: pldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd1_1v8_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_1v8_s3: pldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_1v8_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_3v3_s0: pldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vcc_3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vccio_sd_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ master_pldo6_s3: pldo-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "master_pldo6_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_0v75_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd2l_0v9_ddr_s3: nldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-name = "vdd2l_0v9_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <900000>;
+ };
+ };
+
+ master_nldo3: nldo-reg3 {
+ regulator-name = "master_nldo3";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ avdd_0v75_s0: nldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "avdd_0v75_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v85_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdd_0v85_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+ };
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 09/13] mfd: rk8xx: add rk806 support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Add support for SPI connected rk806, which is used by the RK3588
evaluation boards. The PMIC is advertised to support I2C and SPI,
but the evaluation boards all use SPI. Thus only SPI support is
added here.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/Kconfig | 14 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/rk8xx-core.c | 67 ++++++-
drivers/mfd/rk8xx-spi.c | 115 +++++++++++
include/linux/mfd/rk808.h | 409 ++++++++++++++++++++++++++++++++++++++
5 files changed, 604 insertions(+), 2 deletions(-)
create mode 100644 drivers/mfd/rk8xx-spi.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8e3de443cc3d..85cd5b476fb1 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1219,6 +1219,20 @@ config MFD_RK8XX_I2C
through I2C interface. The device supports multiple sub-devices
including interrupts, RTC, LDO & DCDC regulators, and onkey.
+config MFD_RK8XX_SPI
+ tristate "Rockchip RK806 Power Management Chip"
+ depends on SPI && OF
+ select MFD_CORE
+ select REGMAP_SPI
+ select REGMAP_IRQ
+ select MFD_RK8XX
+ help
+ If you say yes here you get support for the RK806 Power Management
+ chip.
+ This driver provides common support for accessing the device
+ through an SPI interface. The device supports multiple sub-devices
+ including interrupts, LDO & DCDC regulators, and power on-key.
+
config MFD_RN5T618
tristate "Ricoh RN5T567/618 PMIC"
depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index edf84e870f98..e4b01ece4eaa 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -225,6 +225,7 @@ obj-$(CONFIG_MFD_NTXEC) += ntxec.o
obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
+obj-$(CONFIG_MFD_RK8XX_SPI) += rk8xx-spi.o
obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
obj-$(CONFIG_MFD_SYSCON) += syscon.o
diff --git a/drivers/mfd/rk8xx-core.c b/drivers/mfd/rk8xx-core.c
index 098506972710..cdebf8e3d93c 100644
--- a/drivers/mfd/rk8xx-core.c
+++ b/drivers/mfd/rk8xx-core.c
@@ -33,6 +33,11 @@ static const struct resource rk805_key_resources[] = {
DEFINE_RES_IRQ(RK805_IRQ_PWRON_FALL),
};
+static struct resource rk806_pwrkey_resources[] = {
+ DEFINE_RES_IRQ(RK806_IRQ_PWRON_FALL),
+ DEFINE_RES_IRQ(RK806_IRQ_PWRON_RISE),
+};
+
static const struct resource rk817_pwrkey_resources[] = {
DEFINE_RES_IRQ(RK817_IRQ_PWRON_RISE),
DEFINE_RES_IRQ(RK817_IRQ_PWRON_FALL),
@@ -58,6 +63,16 @@ static const struct mfd_cell rk805s[] = {
},
};
+static const struct mfd_cell rk806s[] = {
+ { .name = "rk805-pinctrl", },
+ { .name = "rk808-regulator", },
+ {
+ .name = "rk805-pwrkey",
+ .num_resources = ARRAY_SIZE(rk806_pwrkey_resources),
+ .resources = &rk806_pwrkey_resources[0],
+ },
+};
+
static const struct mfd_cell rk808s[] = {
{ .name = "rk808-clkout", },
{ .name = "rk808-regulator", },
@@ -112,6 +127,12 @@ static const struct rk808_reg_data rk805_pre_init_reg[] = {
{RK805_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP115C},
};
+static const struct rk808_reg_data rk806_pre_init_reg[] = {
+ { RK806_GPIO_INT_CONFIG, RK806_INT_POL_MSK, RK806_INT_POL_L },
+ { RK806_SYS_CFG3, RK806_SLAVE_RESTART_FUN_MSK, RK806_SLAVE_RESTART_FUN_EN },
+ { RK806_SYS_OPTION, RK806_SYS_ENB2_2M_MSK, RK806_SYS_ENB2_2M_EN },
+};
+
static const struct rk808_reg_data rk808_pre_init_reg[] = {
{ RK808_BUCK3_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_150MA },
{ RK808_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_200MA },
@@ -262,6 +283,27 @@ static const struct regmap_irq rk805_irqs[] = {
},
};
+static const struct regmap_irq rk806_irqs[] = {
+ /* INT_STS0 IRQs */
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_FALL, 0, RK806_INT_STS_PWRON_FALL),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_RISE, 0, RK806_INT_STS_PWRON_RISE),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON, 0, RK806_INT_STS_PWRON),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_LP, 0, RK806_INT_STS_PWRON_LP),
+ REGMAP_IRQ_REG(RK806_IRQ_HOTDIE, 0, RK806_INT_STS_HOTDIE),
+ REGMAP_IRQ_REG(RK806_IRQ_VDC_RISE, 0, RK806_INT_STS_VDC_RISE),
+ REGMAP_IRQ_REG(RK806_IRQ_VDC_FALL, 0, RK806_INT_STS_VDC_FALL),
+ REGMAP_IRQ_REG(RK806_IRQ_VB_LO, 0, RK806_INT_STS_VB_LO),
+ /* INT_STS1 IRQs */
+ REGMAP_IRQ_REG(RK806_IRQ_REV0, 1, RK806_INT_STS_REV0),
+ REGMAP_IRQ_REG(RK806_IRQ_REV1, 1, RK806_INT_STS_REV1),
+ REGMAP_IRQ_REG(RK806_IRQ_REV2, 1, RK806_INT_STS_REV2),
+ REGMAP_IRQ_REG(RK806_IRQ_CRC_ERROR, 1, RK806_INT_STS_CRC_ERROR),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP3_GPIO, 1, RK806_INT_STS_SLP3_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP2_GPIO, 1, RK806_INT_STS_SLP2_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP1_GPIO, 1, RK806_INT_STS_SLP1_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_WDT, 1, RK806_INT_STS_WDT),
+};
+
static const struct regmap_irq rk808_irqs[] = {
/* INT_STS */
[RK808_IRQ_VOUT_LO] = {
@@ -412,6 +454,18 @@ static struct regmap_irq_chip rk805_irq_chip = {
.init_ack_masked = true,
};
+static struct regmap_irq_chip rk806_irq_chip = {
+ .name = "rk806",
+ .irqs = rk806_irqs,
+ .num_irqs = ARRAY_SIZE(rk806_irqs),
+ .num_regs = 2,
+ .irq_reg_stride = 2,
+ .mask_base = RK806_INT_MSK0,
+ .status_base = RK806_INT_STS0,
+ .ack_base = RK806_INT_STS0,
+ .init_ack_masked = true,
+};
+
static const struct regmap_irq_chip rk808_irq_chip = {
.name = "rk808",
.irqs = rk808_irqs,
@@ -538,6 +592,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
struct rk808 *rk808;
const struct rk808_reg_data *pre_init_reg;
const struct mfd_cell *cells;
+ bool dual_support = false;
int nr_pre_init_regs;
int nr_cells;
int ret;
@@ -559,6 +614,14 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
cells = rk805s;
nr_cells = ARRAY_SIZE(rk805s);
break;
+ case RK806_ID:
+ rk808->regmap_irq_chip = &rk806_irq_chip;
+ pre_init_reg = rk806_pre_init_reg;
+ nr_pre_init_regs = ARRAY_SIZE(rk806_pre_init_reg);
+ cells = rk806s;
+ nr_cells = ARRAY_SIZE(rk806s);
+ dual_support = true;
+ break;
case RK808_ID:
rk808->regmap_irq_chip = &rk808_irq_chip;
pre_init_reg = rk808_pre_init_reg;
@@ -592,7 +655,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
return dev_err_probe(dev, -EINVAL, "No interrupt support, no core IRQ\n");
ret = devm_regmap_add_irq_chip(dev, rk808->regmap, irq,
- IRQF_ONESHOT, -1,
+ IRQF_ONESHOT | (dual_support ? IRQF_SHARED : 0), -1,
rk808->regmap_irq_chip, &rk808->irq_data);
if (ret)
return dev_err_probe(dev, ret, "Failed to add irq_chip\n");
@@ -607,7 +670,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
pre_init_reg[i].addr);
}
- ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
+ ret = devm_mfd_add_devices(dev, dual_support ? PLATFORM_DEVID_AUTO : PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
if (ret)
diff --git a/drivers/mfd/rk8xx-spi.c b/drivers/mfd/rk8xx-spi.c
new file mode 100644
index 000000000000..79c05327eeaf
--- /dev/null
+++ b/drivers/mfd/rk8xx-spi.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockchip RK806 Core (SPI) driver
+ *
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ *
+ * Author: Xu Shengfei <xsf@rock-chips.com>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rk808.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+static const struct regmap_range rk806_volatile_ranges[] = {
+ regmap_reg_range(RK806_POWER_EN0, RK806_POWER_EN5),
+ regmap_reg_range(RK806_DVS_START_CTRL, RK806_INT_MSK1),
+};
+
+static const struct regmap_access_table rk806_volatile_table = {
+ .yes_ranges = rk806_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(rk806_volatile_ranges),
+};
+
+static const struct regmap_config rk806_regmap_config_spi = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_table = &rk806_volatile_table,
+};
+
+static int rk806_spi_bus_write(void *context, const void *vdata, size_t count)
+{
+ struct device *dev = context;
+ struct spi_device *spi = to_spi_device(dev);
+ const char *data = vdata;
+ char buffer[4] = { 0 };
+
+ /* implementation currently only supports single write */
+ if (count != 2)
+ return -EINVAL;
+
+ buffer[0] = RK806_CMD_WRITE | (count - 2);
+ buffer[1] = data[0]; /* register address */
+ buffer[2] = RK806_REG_H;
+ buffer[3] = data[1]; /* register value */
+
+ return spi_write(spi, &buffer, sizeof(buffer));
+}
+
+static int rk806_spi_bus_read(void *context, const void *vreg, size_t reg_size,
+ void *val, size_t val_size)
+{
+ struct device *dev = context;
+ struct spi_device *spi = to_spi_device(dev);
+ const char *reg = vreg;
+ char txbuf[3] = { 0 };
+
+ if (reg_size != sizeof(char) || val_size < 1)
+ return -EINVAL;
+
+ txbuf[0] = RK806_CMD_READ | (val_size - 1);
+ txbuf[1] = *reg;
+ txbuf[2] = RK806_REG_H;
+
+ return spi_write_then_read(spi, txbuf, sizeof(txbuf), val, val_size);
+}
+
+static const struct regmap_bus rk806_regmap_bus_spi = {
+ .write = rk806_spi_bus_write,
+ .read = rk806_spi_bus_read,
+ .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
+ .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
+};
+
+static int rk8xx_spi_probe(struct spi_device *spi)
+{
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init(&spi->dev, &rk806_regmap_bus_spi,
+ &spi->dev, &rk806_regmap_config_spi);
+ if (IS_ERR(regmap))
+ return dev_err_probe(&spi->dev, PTR_ERR(regmap),
+ "Failed to initialize register map\n");
+
+ return rk8xx_probe(&spi->dev, RK806_ID, spi->irq, regmap);
+}
+
+static const struct of_device_id rk8xx_spi_of_match[] = {
+ { .compatible = "rockchip,rk806", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rk8xx_spi_of_match);
+
+static const struct spi_device_id rk8xx_spi_id_table[] = {
+ { "rk806", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, rk8xx_spi_id_table);
+
+static struct spi_driver rk8xx_spi_driver = {
+ .driver = {
+ .name = "rk8xx-spi",
+ .of_match_table = rk8xx_spi_of_match,
+ },
+ .probe = rk8xx_spi_probe,
+ .id_table = rk8xx_spi_id_table,
+};
+module_spi_driver(rk8xx_spi_driver);
+
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
+MODULE_DESCRIPTION("RK8xx SPI PMIC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 4183427a80fe..78e167a92483 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -289,6 +289,414 @@ enum rk805_reg {
#define RK805_INT_ALARM_EN (1 << 3)
#define RK805_INT_TIMER_EN (1 << 2)
+/* RK806 */
+#define RK806_POWER_EN0 0x0
+#define RK806_POWER_EN1 0x1
+#define RK806_POWER_EN2 0x2
+#define RK806_POWER_EN3 0x3
+#define RK806_POWER_EN4 0x4
+#define RK806_POWER_EN5 0x5
+#define RK806_POWER_SLP_EN0 0x6
+#define RK806_POWER_SLP_EN1 0x7
+#define RK806_POWER_SLP_EN2 0x8
+#define RK806_POWER_DISCHRG_EN0 0x9
+#define RK806_POWER_DISCHRG_EN1 0xA
+#define RK806_POWER_DISCHRG_EN2 0xB
+#define RK806_BUCK_FB_CONFIG 0xC
+#define RK806_SLP_LP_CONFIG 0xD
+#define RK806_POWER_FPWM_EN0 0xE
+#define RK806_POWER_FPWM_EN1 0xF
+#define RK806_BUCK1_CONFIG 0x10
+#define RK806_BUCK2_CONFIG 0x11
+#define RK806_BUCK3_CONFIG 0x12
+#define RK806_BUCK4_CONFIG 0x13
+#define RK806_BUCK5_CONFIG 0x14
+#define RK806_BUCK6_CONFIG 0x15
+#define RK806_BUCK7_CONFIG 0x16
+#define RK806_BUCK8_CONFIG 0x17
+#define RK806_BUCK9_CONFIG 0x18
+#define RK806_BUCK10_CONFIG 0x19
+#define RK806_BUCK1_ON_VSEL 0x1A
+#define RK806_BUCK2_ON_VSEL 0x1B
+#define RK806_BUCK3_ON_VSEL 0x1C
+#define RK806_BUCK4_ON_VSEL 0x1D
+#define RK806_BUCK5_ON_VSEL 0x1E
+#define RK806_BUCK6_ON_VSEL 0x1F
+#define RK806_BUCK7_ON_VSEL 0x20
+#define RK806_BUCK8_ON_VSEL 0x21
+#define RK806_BUCK9_ON_VSEL 0x22
+#define RK806_BUCK10_ON_VSEL 0x23
+#define RK806_BUCK1_SLP_VSEL 0x24
+#define RK806_BUCK2_SLP_VSEL 0x25
+#define RK806_BUCK3_SLP_VSEL 0x26
+#define RK806_BUCK4_SLP_VSEL 0x27
+#define RK806_BUCK5_SLP_VSEL 0x28
+#define RK806_BUCK6_SLP_VSEL 0x29
+#define RK806_BUCK7_SLP_VSEL 0x2A
+#define RK806_BUCK8_SLP_VSEL 0x2B
+#define RK806_BUCK9_SLP_VSEL 0x2D
+#define RK806_BUCK10_SLP_VSEL 0x2E
+#define RK806_BUCK_DEBUG1 0x30
+#define RK806_BUCK_DEBUG2 0x31
+#define RK806_BUCK_DEBUG3 0x32
+#define RK806_BUCK_DEBUG4 0x33
+#define RK806_BUCK_DEBUG5 0x34
+#define RK806_BUCK_DEBUG6 0x35
+#define RK806_BUCK_DEBUG7 0x36
+#define RK806_BUCK_DEBUG8 0x37
+#define RK806_BUCK_DEBUG9 0x38
+#define RK806_BUCK_DEBUG10 0x39
+#define RK806_BUCK_DEBUG11 0x3A
+#define RK806_BUCK_DEBUG12 0x3B
+#define RK806_BUCK_DEBUG13 0x3C
+#define RK806_BUCK_DEBUG14 0x3D
+#define RK806_BUCK_DEBUG15 0x3E
+#define RK806_BUCK_DEBUG16 0x3F
+#define RK806_BUCK_DEBUG17 0x40
+#define RK806_BUCK_DEBUG18 0x41
+#define RK806_NLDO_IMAX 0x42
+#define RK806_NLDO1_ON_VSEL 0x43
+#define RK806_NLDO2_ON_VSEL 0x44
+#define RK806_NLDO3_ON_VSEL 0x45
+#define RK806_NLDO4_ON_VSEL 0x46
+#define RK806_NLDO5_ON_VSEL 0x47
+#define RK806_NLDO1_SLP_VSEL 0x48
+#define RK806_NLDO2_SLP_VSEL 0x49
+#define RK806_NLDO3_SLP_VSEL 0x4A
+#define RK806_NLDO4_SLP_VSEL 0x4B
+#define RK806_NLDO5_SLP_VSEL 0x4C
+#define RK806_PLDO_IMAX 0x4D
+#define RK806_PLDO1_ON_VSEL 0x4E
+#define RK806_PLDO2_ON_VSEL 0x4F
+#define RK806_PLDO3_ON_VSEL 0x50
+#define RK806_PLDO4_ON_VSEL 0x51
+#define RK806_PLDO5_ON_VSEL 0x52
+#define RK806_PLDO6_ON_VSEL 0x53
+#define RK806_PLDO1_SLP_VSEL 0x54
+#define RK806_PLDO2_SLP_VSEL 0x55
+#define RK806_PLDO3_SLP_VSEL 0x56
+#define RK806_PLDO4_SLP_VSEL 0x57
+#define RK806_PLDO5_SLP_VSEL 0x58
+#define RK806_PLDO6_SLP_VSEL 0x59
+#define RK806_CHIP_NAME 0x5A
+#define RK806_CHIP_VER 0x5B
+#define RK806_OTP_VER 0x5C
+#define RK806_SYS_STS 0x5D
+#define RK806_SYS_CFG0 0x5E
+#define RK806_SYS_CFG1 0x5F
+#define RK806_SYS_OPTION 0x61
+#define RK806_SLEEP_CONFIG0 0x62
+#define RK806_SLEEP_CONFIG1 0x63
+#define RK806_SLEEP_CTR_SEL0 0x64
+#define RK806_SLEEP_CTR_SEL1 0x65
+#define RK806_SLEEP_CTR_SEL2 0x66
+#define RK806_SLEEP_CTR_SEL3 0x67
+#define RK806_SLEEP_CTR_SEL4 0x68
+#define RK806_SLEEP_CTR_SEL5 0x69
+#define RK806_DVS_CTRL_SEL0 0x6A
+#define RK806_DVS_CTRL_SEL1 0x6B
+#define RK806_DVS_CTRL_SEL2 0x6C
+#define RK806_DVS_CTRL_SEL3 0x6D
+#define RK806_DVS_CTRL_SEL4 0x6E
+#define RK806_DVS_CTRL_SEL5 0x6F
+#define RK806_DVS_START_CTRL 0x70
+#define RK806_SLEEP_GPIO 0x71
+#define RK806_SYS_CFG3 0x72
+#define RK806_ON_SOURCE 0x74
+#define RK806_OFF_SOURCE 0x75
+#define RK806_PWRON_KEY 0x76
+#define RK806_INT_STS0 0x77
+#define RK806_INT_MSK0 0x78
+#define RK806_INT_STS1 0x79
+#define RK806_INT_MSK1 0x7A
+#define RK806_GPIO_INT_CONFIG 0x7B
+#define RK806_DATA_REG0 0x7C
+#define RK806_DATA_REG1 0x7D
+#define RK806_DATA_REG2 0x7E
+#define RK806_DATA_REG3 0x7F
+#define RK806_DATA_REG4 0x80
+#define RK806_DATA_REG5 0x81
+#define RK806_DATA_REG6 0x82
+#define RK806_DATA_REG7 0x83
+#define RK806_DATA_REG8 0x84
+#define RK806_DATA_REG9 0x85
+#define RK806_DATA_REG10 0x86
+#define RK806_DATA_REG11 0x87
+#define RK806_DATA_REG12 0x88
+#define RK806_DATA_REG13 0x89
+#define RK806_DATA_REG14 0x8A
+#define RK806_DATA_REG15 0x8B
+#define RK806_TM_REG 0x8C
+#define RK806_OTP_EN_REG 0x8D
+#define RK806_FUNC_OTP_EN_REG 0x8E
+#define RK806_TEST_REG1 0x8F
+#define RK806_TEST_REG2 0x90
+#define RK806_TEST_REG3 0x91
+#define RK806_TEST_REG4 0x92
+#define RK806_TEST_REG5 0x93
+#define RK806_BUCK_VSEL_OTP_REG0 0x94
+#define RK806_BUCK_VSEL_OTP_REG1 0x95
+#define RK806_BUCK_VSEL_OTP_REG2 0x96
+#define RK806_BUCK_VSEL_OTP_REG3 0x97
+#define RK806_BUCK_VSEL_OTP_REG4 0x98
+#define RK806_BUCK_VSEL_OTP_REG5 0x99
+#define RK806_BUCK_VSEL_OTP_REG6 0x9A
+#define RK806_BUCK_VSEL_OTP_REG7 0x9B
+#define RK806_BUCK_VSEL_OTP_REG8 0x9C
+#define RK806_BUCK_VSEL_OTP_REG9 0x9D
+#define RK806_NLDO1_VSEL_OTP_REG0 0x9E
+#define RK806_NLDO1_VSEL_OTP_REG1 0x9F
+#define RK806_NLDO1_VSEL_OTP_REG2 0xA0
+#define RK806_NLDO1_VSEL_OTP_REG3 0xA1
+#define RK806_NLDO1_VSEL_OTP_REG4 0xA2
+#define RK806_PLDO_VSEL_OTP_REG0 0xA3
+#define RK806_PLDO_VSEL_OTP_REG1 0xA4
+#define RK806_PLDO_VSEL_OTP_REG2 0xA5
+#define RK806_PLDO_VSEL_OTP_REG3 0xA6
+#define RK806_PLDO_VSEL_OTP_REG4 0xA7
+#define RK806_PLDO_VSEL_OTP_REG5 0xA8
+#define RK806_BUCK_EN_OTP_REG1 0xA9
+#define RK806_NLDO_EN_OTP_REG1 0xAA
+#define RK806_PLDO_EN_OTP_REG1 0xAB
+#define RK806_BUCK_FB_RES_OTP_REG1 0xAC
+#define RK806_OTP_RESEV_REG0 0xAD
+#define RK806_OTP_RESEV_REG1 0xAE
+#define RK806_OTP_RESEV_REG2 0xAF
+#define RK806_OTP_RESEV_REG3 0xB0
+#define RK806_OTP_RESEV_REG4 0xB1
+#define RK806_BUCK_SEQ_REG0 0xB2
+#define RK806_BUCK_SEQ_REG1 0xB3
+#define RK806_BUCK_SEQ_REG2 0xB4
+#define RK806_BUCK_SEQ_REG3 0xB5
+#define RK806_BUCK_SEQ_REG4 0xB6
+#define RK806_BUCK_SEQ_REG5 0xB7
+#define RK806_BUCK_SEQ_REG6 0xB8
+#define RK806_BUCK_SEQ_REG7 0xB9
+#define RK806_BUCK_SEQ_REG8 0xBA
+#define RK806_BUCK_SEQ_REG9 0xBB
+#define RK806_BUCK_SEQ_REG10 0xBC
+#define RK806_BUCK_SEQ_REG11 0xBD
+#define RK806_BUCK_SEQ_REG12 0xBE
+#define RK806_BUCK_SEQ_REG13 0xBF
+#define RK806_BUCK_SEQ_REG14 0xC0
+#define RK806_BUCK_SEQ_REG15 0xC1
+#define RK806_BUCK_SEQ_REG16 0xC2
+#define RK806_BUCK_SEQ_REG17 0xC3
+#define RK806_HK_TRIM_REG1 0xC4
+#define RK806_HK_TRIM_REG2 0xC5
+#define RK806_BUCK_REF_TRIM_REG1 0xC6
+#define RK806_BUCK_REF_TRIM_REG2 0xC7
+#define RK806_BUCK_REF_TRIM_REG3 0xC8
+#define RK806_BUCK_REF_TRIM_REG4 0xC9
+#define RK806_BUCK_REF_TRIM_REG5 0xCA
+#define RK806_BUCK_OSC_TRIM_REG1 0xCB
+#define RK806_BUCK_OSC_TRIM_REG2 0xCC
+#define RK806_BUCK_OSC_TRIM_REG3 0xCD
+#define RK806_BUCK_OSC_TRIM_REG4 0xCE
+#define RK806_BUCK_OSC_TRIM_REG5 0xCF
+#define RK806_BUCK_TRIM_ZCDIOS_REG1 0xD0
+#define RK806_BUCK_TRIM_ZCDIOS_REG2 0xD1
+#define RK806_NLDO_TRIM_REG1 0xD2
+#define RK806_NLDO_TRIM_REG2 0xD3
+#define RK806_NLDO_TRIM_REG3 0xD4
+#define RK806_PLDO_TRIM_REG1 0xD5
+#define RK806_PLDO_TRIM_REG2 0xD6
+#define RK806_PLDO_TRIM_REG3 0xD7
+#define RK806_TRIM_ICOMP_REG1 0xD8
+#define RK806_TRIM_ICOMP_REG2 0xD9
+#define RK806_EFUSE_CONTROL_REGH 0xDA
+#define RK806_FUSE_PROG_REG 0xDB
+#define RK806_MAIN_FSM_STS_REG 0xDD
+#define RK806_FSM_REG 0xDE
+#define RK806_TOP_RESEV_OFFR 0xEC
+#define RK806_TOP_RESEV_POR 0xED
+#define RK806_BUCK_VRSN_REG1 0xEE
+#define RK806_BUCK_VRSN_REG2 0xEF
+#define RK806_NLDO_RLOAD_SEL_REG1 0xF0
+#define RK806_PLDO_RLOAD_SEL_REG1 0xF1
+#define RK806_PLDO_RLOAD_SEL_REG2 0xF2
+#define RK806_BUCK_CMIN_MX_REG1 0xF3
+#define RK806_BUCK_CMIN_MX_REG2 0xF4
+#define RK806_BUCK_FREQ_SET_REG1 0xF5
+#define RK806_BUCK_FREQ_SET_REG2 0xF6
+#define RK806_BUCK_RS_MEABS_REG1 0xF7
+#define RK806_BUCK_RS_MEABS_REG2 0xF8
+#define RK806_BUCK_RS_ZDLEB_REG1 0xF9
+#define RK806_BUCK_RS_ZDLEB_REG2 0xFA
+#define RK806_BUCK_RSERVE_REG1 0xFB
+#define RK806_BUCK_RSERVE_REG2 0xFC
+#define RK806_BUCK_RSERVE_REG3 0xFD
+#define RK806_BUCK_RSERVE_REG4 0xFE
+#define RK806_BUCK_RSERVE_REG5 0xFF
+
+/* INT_STS Register field definitions */
+#define RK806_INT_STS_PWRON_FALL BIT(0)
+#define RK806_INT_STS_PWRON_RISE BIT(1)
+#define RK806_INT_STS_PWRON BIT(2)
+#define RK806_INT_STS_PWRON_LP BIT(3)
+#define RK806_INT_STS_HOTDIE BIT(4)
+#define RK806_INT_STS_VDC_RISE BIT(5)
+#define RK806_INT_STS_VDC_FALL BIT(6)
+#define RK806_INT_STS_VB_LO BIT(7)
+#define RK806_INT_STS_REV0 BIT(0)
+#define RK806_INT_STS_REV1 BIT(1)
+#define RK806_INT_STS_REV2 BIT(2)
+#define RK806_INT_STS_CRC_ERROR BIT(3)
+#define RK806_INT_STS_SLP3_GPIO BIT(4)
+#define RK806_INT_STS_SLP2_GPIO BIT(5)
+#define RK806_INT_STS_SLP1_GPIO BIT(6)
+#define RK806_INT_STS_WDT BIT(7)
+
+/* SPI command */
+#define RK806_CMD_READ 0
+#define RK806_CMD_WRITE BIT(7)
+#define RK806_CMD_CRC_EN BIT(6)
+#define RK806_CMD_CRC_DIS 0
+#define RK806_CMD_LEN_MSK 0x0f
+#define RK806_REG_H 0x00
+
+#define VERSION_AB 0x01
+
+enum rk806_reg_id {
+ RK806_ID_DCDC1 = 0,
+ RK806_ID_DCDC2,
+ RK806_ID_DCDC3,
+ RK806_ID_DCDC4,
+ RK806_ID_DCDC5,
+ RK806_ID_DCDC6,
+ RK806_ID_DCDC7,
+ RK806_ID_DCDC8,
+ RK806_ID_DCDC9,
+ RK806_ID_DCDC10,
+
+ RK806_ID_NLDO1,
+ RK806_ID_NLDO2,
+ RK806_ID_NLDO3,
+ RK806_ID_NLDO4,
+ RK806_ID_NLDO5,
+
+ RK806_ID_PLDO1,
+ RK806_ID_PLDO2,
+ RK806_ID_PLDO3,
+ RK806_ID_PLDO4,
+ RK806_ID_PLDO5,
+ RK806_ID_PLDO6,
+ RK806_ID_END,
+};
+
+/* Define the RK806 IRQ numbers */
+enum rk806_irqs {
+ /* INT_STS0 registers */
+ RK806_IRQ_PWRON_FALL,
+ RK806_IRQ_PWRON_RISE,
+ RK806_IRQ_PWRON,
+ RK806_IRQ_PWRON_LP,
+ RK806_IRQ_HOTDIE,
+ RK806_IRQ_VDC_RISE,
+ RK806_IRQ_VDC_FALL,
+ RK806_IRQ_VB_LO,
+
+ /* INT_STS0 registers */
+ RK806_IRQ_REV0,
+ RK806_IRQ_REV1,
+ RK806_IRQ_REV2,
+ RK806_IRQ_CRC_ERROR,
+ RK806_IRQ_SLP3_GPIO,
+ RK806_IRQ_SLP2_GPIO,
+ RK806_IRQ_SLP1_GPIO,
+ RK806_IRQ_WDT,
+};
+
+/* VCC1 Low Voltage Threshold */
+enum rk806_lv_sel {
+ VB_LO_SEL_2800,
+ VB_LO_SEL_2900,
+ VB_LO_SEL_3000,
+ VB_LO_SEL_3100,
+ VB_LO_SEL_3200,
+ VB_LO_SEL_3300,
+ VB_LO_SEL_3400,
+ VB_LO_SEL_3500,
+};
+
+/* System Shutdown Voltage Select */
+enum rk806_uv_sel {
+ VB_UV_SEL_2700,
+ VB_UV_SEL_2800,
+ VB_UV_SEL_2900,
+ VB_UV_SEL_3000,
+ VB_UV_SEL_3100,
+ VB_UV_SEL_3200,
+ VB_UV_SEL_3300,
+ VB_UV_SEL_3400,
+};
+
+/* Pin Function */
+enum rk806_pwrctrl_fun {
+ PWRCTRL_NULL_FUN,
+ PWRCTRL_SLP_FUN,
+ PWRCTRL_POWOFF_FUN,
+ PWRCTRL_RST_FUN,
+ PWRCTRL_DVS_FUN,
+ PWRCTRL_GPIO_FUN,
+};
+
+/* Pin Polarity */
+enum rk806_pin_level {
+ POL_LOW,
+ POL_HIGH,
+};
+
+enum rk806_vsel_ctr_sel {
+ CTR_BY_NO_EFFECT,
+ CTR_BY_PWRCTRL1,
+ CTR_BY_PWRCTRL2,
+ CTR_BY_PWRCTRL3,
+};
+
+enum rk806_dvs_ctr_sel {
+ CTR_SEL_NO_EFFECT,
+ CTR_SEL_DVS_START1,
+ CTR_SEL_DVS_START2,
+ CTR_SEL_DVS_START3,
+};
+
+enum rk806_pin_dr_sel {
+ RK806_PIN_INPUT,
+ RK806_PIN_OUTPUT,
+};
+
+#define RK806_INT_POL_MSK BIT(1)
+#define RK806_INT_POL_H BIT(1)
+#define RK806_INT_POL_L 0
+
+#define RK806_SLAVE_RESTART_FUN_MSK BIT(1)
+#define RK806_SLAVE_RESTART_FUN_EN BIT(1)
+#define RK806_SLAVE_RESTART_FUN_OFF 0
+
+#define RK806_SYS_ENB2_2M_MSK BIT(1)
+#define RK806_SYS_ENB2_2M_EN BIT(1)
+#define RK806_SYS_ENB2_2M_OFF 0
+
+enum rk806_int_fun {
+ RK806_INT_ONLY,
+ RK806_INT_ADN_WKUP,
+};
+
+enum rk806_dvs_mode {
+ RK806_DVS_NOT_SUPPORT,
+ RK806_DVS_START1,
+ RK806_DVS_START2,
+ RK806_DVS_START3,
+ RK806_DVS_PWRCTRL1,
+ RK806_DVS_PWRCTRL2,
+ RK806_DVS_PWRCTRL3,
+ RK806_DVS_START_PWRCTR1,
+ RK806_DVS_START_PWRCTR2,
+ RK806_DVS_START_PWRCTR3,
+ RK806_DVS_END,
+};
+
/* RK808 IRQ Definitions */
#define RK808_IRQ_VOUT_LO 0
#define RK808_IRQ_VB_LO 1
@@ -780,6 +1188,7 @@ enum {
enum {
RK805_ID = 0x8050,
+ RK806_ID = 0x8060,
RK808_ID = 0x0000,
RK809_ID = 0x8090,
RK817_ID = 0x8170,
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 09/13] mfd: rk8xx: add rk806 support
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Add support for SPI connected rk806, which is used by the RK3588
evaluation boards. The PMIC is advertised to support I2C and SPI,
but the evaluation boards all use SPI. Thus only SPI support is
added here.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/mfd/Kconfig | 14 ++
drivers/mfd/Makefile | 1 +
drivers/mfd/rk8xx-core.c | 67 ++++++-
drivers/mfd/rk8xx-spi.c | 115 +++++++++++
include/linux/mfd/rk808.h | 409 ++++++++++++++++++++++++++++++++++++++
5 files changed, 604 insertions(+), 2 deletions(-)
create mode 100644 drivers/mfd/rk8xx-spi.c
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 8e3de443cc3d..85cd5b476fb1 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1219,6 +1219,20 @@ config MFD_RK8XX_I2C
through I2C interface. The device supports multiple sub-devices
including interrupts, RTC, LDO & DCDC regulators, and onkey.
+config MFD_RK8XX_SPI
+ tristate "Rockchip RK806 Power Management Chip"
+ depends on SPI && OF
+ select MFD_CORE
+ select REGMAP_SPI
+ select REGMAP_IRQ
+ select MFD_RK8XX
+ help
+ If you say yes here you get support for the RK806 Power Management
+ chip.
+ This driver provides common support for accessing the device
+ through an SPI interface. The device supports multiple sub-devices
+ including interrupts, LDO & DCDC regulators, and power on-key.
+
config MFD_RN5T618
tristate "Ricoh RN5T567/618 PMIC"
depends on I2C
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index edf84e870f98..e4b01ece4eaa 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -225,6 +225,7 @@ obj-$(CONFIG_MFD_NTXEC) += ntxec.o
obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
+obj-$(CONFIG_MFD_RK8XX_SPI) += rk8xx-spi.o
obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
obj-$(CONFIG_MFD_SYSCON) += syscon.o
diff --git a/drivers/mfd/rk8xx-core.c b/drivers/mfd/rk8xx-core.c
index 098506972710..cdebf8e3d93c 100644
--- a/drivers/mfd/rk8xx-core.c
+++ b/drivers/mfd/rk8xx-core.c
@@ -33,6 +33,11 @@ static const struct resource rk805_key_resources[] = {
DEFINE_RES_IRQ(RK805_IRQ_PWRON_FALL),
};
+static struct resource rk806_pwrkey_resources[] = {
+ DEFINE_RES_IRQ(RK806_IRQ_PWRON_FALL),
+ DEFINE_RES_IRQ(RK806_IRQ_PWRON_RISE),
+};
+
static const struct resource rk817_pwrkey_resources[] = {
DEFINE_RES_IRQ(RK817_IRQ_PWRON_RISE),
DEFINE_RES_IRQ(RK817_IRQ_PWRON_FALL),
@@ -58,6 +63,16 @@ static const struct mfd_cell rk805s[] = {
},
};
+static const struct mfd_cell rk806s[] = {
+ { .name = "rk805-pinctrl", },
+ { .name = "rk808-regulator", },
+ {
+ .name = "rk805-pwrkey",
+ .num_resources = ARRAY_SIZE(rk806_pwrkey_resources),
+ .resources = &rk806_pwrkey_resources[0],
+ },
+};
+
static const struct mfd_cell rk808s[] = {
{ .name = "rk808-clkout", },
{ .name = "rk808-regulator", },
@@ -112,6 +127,12 @@ static const struct rk808_reg_data rk805_pre_init_reg[] = {
{RK805_THERMAL_REG, TEMP_HOTDIE_MSK, TEMP115C},
};
+static const struct rk808_reg_data rk806_pre_init_reg[] = {
+ { RK806_GPIO_INT_CONFIG, RK806_INT_POL_MSK, RK806_INT_POL_L },
+ { RK806_SYS_CFG3, RK806_SLAVE_RESTART_FUN_MSK, RK806_SLAVE_RESTART_FUN_EN },
+ { RK806_SYS_OPTION, RK806_SYS_ENB2_2M_MSK, RK806_SYS_ENB2_2M_EN },
+};
+
static const struct rk808_reg_data rk808_pre_init_reg[] = {
{ RK808_BUCK3_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_150MA },
{ RK808_BUCK4_CONFIG_REG, BUCK_ILMIN_MASK, BUCK_ILMIN_200MA },
@@ -262,6 +283,27 @@ static const struct regmap_irq rk805_irqs[] = {
},
};
+static const struct regmap_irq rk806_irqs[] = {
+ /* INT_STS0 IRQs */
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_FALL, 0, RK806_INT_STS_PWRON_FALL),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_RISE, 0, RK806_INT_STS_PWRON_RISE),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON, 0, RK806_INT_STS_PWRON),
+ REGMAP_IRQ_REG(RK806_IRQ_PWRON_LP, 0, RK806_INT_STS_PWRON_LP),
+ REGMAP_IRQ_REG(RK806_IRQ_HOTDIE, 0, RK806_INT_STS_HOTDIE),
+ REGMAP_IRQ_REG(RK806_IRQ_VDC_RISE, 0, RK806_INT_STS_VDC_RISE),
+ REGMAP_IRQ_REG(RK806_IRQ_VDC_FALL, 0, RK806_INT_STS_VDC_FALL),
+ REGMAP_IRQ_REG(RK806_IRQ_VB_LO, 0, RK806_INT_STS_VB_LO),
+ /* INT_STS1 IRQs */
+ REGMAP_IRQ_REG(RK806_IRQ_REV0, 1, RK806_INT_STS_REV0),
+ REGMAP_IRQ_REG(RK806_IRQ_REV1, 1, RK806_INT_STS_REV1),
+ REGMAP_IRQ_REG(RK806_IRQ_REV2, 1, RK806_INT_STS_REV2),
+ REGMAP_IRQ_REG(RK806_IRQ_CRC_ERROR, 1, RK806_INT_STS_CRC_ERROR),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP3_GPIO, 1, RK806_INT_STS_SLP3_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP2_GPIO, 1, RK806_INT_STS_SLP2_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_SLP1_GPIO, 1, RK806_INT_STS_SLP1_GPIO),
+ REGMAP_IRQ_REG(RK806_IRQ_WDT, 1, RK806_INT_STS_WDT),
+};
+
static const struct regmap_irq rk808_irqs[] = {
/* INT_STS */
[RK808_IRQ_VOUT_LO] = {
@@ -412,6 +454,18 @@ static struct regmap_irq_chip rk805_irq_chip = {
.init_ack_masked = true,
};
+static struct regmap_irq_chip rk806_irq_chip = {
+ .name = "rk806",
+ .irqs = rk806_irqs,
+ .num_irqs = ARRAY_SIZE(rk806_irqs),
+ .num_regs = 2,
+ .irq_reg_stride = 2,
+ .mask_base = RK806_INT_MSK0,
+ .status_base = RK806_INT_STS0,
+ .ack_base = RK806_INT_STS0,
+ .init_ack_masked = true,
+};
+
static const struct regmap_irq_chip rk808_irq_chip = {
.name = "rk808",
.irqs = rk808_irqs,
@@ -538,6 +592,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
struct rk808 *rk808;
const struct rk808_reg_data *pre_init_reg;
const struct mfd_cell *cells;
+ bool dual_support = false;
int nr_pre_init_regs;
int nr_cells;
int ret;
@@ -559,6 +614,14 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
cells = rk805s;
nr_cells = ARRAY_SIZE(rk805s);
break;
+ case RK806_ID:
+ rk808->regmap_irq_chip = &rk806_irq_chip;
+ pre_init_reg = rk806_pre_init_reg;
+ nr_pre_init_regs = ARRAY_SIZE(rk806_pre_init_reg);
+ cells = rk806s;
+ nr_cells = ARRAY_SIZE(rk806s);
+ dual_support = true;
+ break;
case RK808_ID:
rk808->regmap_irq_chip = &rk808_irq_chip;
pre_init_reg = rk808_pre_init_reg;
@@ -592,7 +655,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
return dev_err_probe(dev, -EINVAL, "No interrupt support, no core IRQ\n");
ret = devm_regmap_add_irq_chip(dev, rk808->regmap, irq,
- IRQF_ONESHOT, -1,
+ IRQF_ONESHOT | (dual_support ? IRQF_SHARED : 0), -1,
rk808->regmap_irq_chip, &rk808->irq_data);
if (ret)
return dev_err_probe(dev, ret, "Failed to add irq_chip\n");
@@ -607,7 +670,7 @@ int rk8xx_probe(struct device *dev, int variant, unsigned int irq, struct regmap
pre_init_reg[i].addr);
}
- ret = devm_mfd_add_devices(dev, PLATFORM_DEVID_NONE,
+ ret = devm_mfd_add_devices(dev, dual_support ? PLATFORM_DEVID_AUTO : PLATFORM_DEVID_NONE,
cells, nr_cells, NULL, 0,
regmap_irq_get_domain(rk808->irq_data));
if (ret)
diff --git a/drivers/mfd/rk8xx-spi.c b/drivers/mfd/rk8xx-spi.c
new file mode 100644
index 000000000000..79c05327eeaf
--- /dev/null
+++ b/drivers/mfd/rk8xx-spi.c
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Rockchip RK806 Core (SPI) driver
+ *
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ *
+ * Author: Xu Shengfei <xsf@rock-chips.com>
+ */
+
+#include <linux/interrupt.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/rk808.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/spi/spi.h>
+
+static const struct regmap_range rk806_volatile_ranges[] = {
+ regmap_reg_range(RK806_POWER_EN0, RK806_POWER_EN5),
+ regmap_reg_range(RK806_DVS_START_CTRL, RK806_INT_MSK1),
+};
+
+static const struct regmap_access_table rk806_volatile_table = {
+ .yes_ranges = rk806_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(rk806_volatile_ranges),
+};
+
+static const struct regmap_config rk806_regmap_config_spi = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_table = &rk806_volatile_table,
+};
+
+static int rk806_spi_bus_write(void *context, const void *vdata, size_t count)
+{
+ struct device *dev = context;
+ struct spi_device *spi = to_spi_device(dev);
+ const char *data = vdata;
+ char buffer[4] = { 0 };
+
+ /* implementation currently only supports single write */
+ if (count != 2)
+ return -EINVAL;
+
+ buffer[0] = RK806_CMD_WRITE | (count - 2);
+ buffer[1] = data[0]; /* register address */
+ buffer[2] = RK806_REG_H;
+ buffer[3] = data[1]; /* register value */
+
+ return spi_write(spi, &buffer, sizeof(buffer));
+}
+
+static int rk806_spi_bus_read(void *context, const void *vreg, size_t reg_size,
+ void *val, size_t val_size)
+{
+ struct device *dev = context;
+ struct spi_device *spi = to_spi_device(dev);
+ const char *reg = vreg;
+ char txbuf[3] = { 0 };
+
+ if (reg_size != sizeof(char) || val_size < 1)
+ return -EINVAL;
+
+ txbuf[0] = RK806_CMD_READ | (val_size - 1);
+ txbuf[1] = *reg;
+ txbuf[2] = RK806_REG_H;
+
+ return spi_write_then_read(spi, txbuf, sizeof(txbuf), val, val_size);
+}
+
+static const struct regmap_bus rk806_regmap_bus_spi = {
+ .write = rk806_spi_bus_write,
+ .read = rk806_spi_bus_read,
+ .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
+ .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
+};
+
+static int rk8xx_spi_probe(struct spi_device *spi)
+{
+ struct regmap *regmap;
+
+ regmap = devm_regmap_init(&spi->dev, &rk806_regmap_bus_spi,
+ &spi->dev, &rk806_regmap_config_spi);
+ if (IS_ERR(regmap))
+ return dev_err_probe(&spi->dev, PTR_ERR(regmap),
+ "Failed to initialize register map\n");
+
+ return rk8xx_probe(&spi->dev, RK806_ID, spi->irq, regmap);
+}
+
+static const struct of_device_id rk8xx_spi_of_match[] = {
+ { .compatible = "rockchip,rk806", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, rk8xx_spi_of_match);
+
+static const struct spi_device_id rk8xx_spi_id_table[] = {
+ { "rk806", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, rk8xx_spi_id_table);
+
+static struct spi_driver rk8xx_spi_driver = {
+ .driver = {
+ .name = "rk8xx-spi",
+ .of_match_table = rk8xx_spi_of_match,
+ },
+ .probe = rk8xx_spi_probe,
+ .id_table = rk8xx_spi_id_table,
+};
+module_spi_driver(rk8xx_spi_driver);
+
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
+MODULE_DESCRIPTION("RK8xx SPI PMIC driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
index 4183427a80fe..78e167a92483 100644
--- a/include/linux/mfd/rk808.h
+++ b/include/linux/mfd/rk808.h
@@ -289,6 +289,414 @@ enum rk805_reg {
#define RK805_INT_ALARM_EN (1 << 3)
#define RK805_INT_TIMER_EN (1 << 2)
+/* RK806 */
+#define RK806_POWER_EN0 0x0
+#define RK806_POWER_EN1 0x1
+#define RK806_POWER_EN2 0x2
+#define RK806_POWER_EN3 0x3
+#define RK806_POWER_EN4 0x4
+#define RK806_POWER_EN5 0x5
+#define RK806_POWER_SLP_EN0 0x6
+#define RK806_POWER_SLP_EN1 0x7
+#define RK806_POWER_SLP_EN2 0x8
+#define RK806_POWER_DISCHRG_EN0 0x9
+#define RK806_POWER_DISCHRG_EN1 0xA
+#define RK806_POWER_DISCHRG_EN2 0xB
+#define RK806_BUCK_FB_CONFIG 0xC
+#define RK806_SLP_LP_CONFIG 0xD
+#define RK806_POWER_FPWM_EN0 0xE
+#define RK806_POWER_FPWM_EN1 0xF
+#define RK806_BUCK1_CONFIG 0x10
+#define RK806_BUCK2_CONFIG 0x11
+#define RK806_BUCK3_CONFIG 0x12
+#define RK806_BUCK4_CONFIG 0x13
+#define RK806_BUCK5_CONFIG 0x14
+#define RK806_BUCK6_CONFIG 0x15
+#define RK806_BUCK7_CONFIG 0x16
+#define RK806_BUCK8_CONFIG 0x17
+#define RK806_BUCK9_CONFIG 0x18
+#define RK806_BUCK10_CONFIG 0x19
+#define RK806_BUCK1_ON_VSEL 0x1A
+#define RK806_BUCK2_ON_VSEL 0x1B
+#define RK806_BUCK3_ON_VSEL 0x1C
+#define RK806_BUCK4_ON_VSEL 0x1D
+#define RK806_BUCK5_ON_VSEL 0x1E
+#define RK806_BUCK6_ON_VSEL 0x1F
+#define RK806_BUCK7_ON_VSEL 0x20
+#define RK806_BUCK8_ON_VSEL 0x21
+#define RK806_BUCK9_ON_VSEL 0x22
+#define RK806_BUCK10_ON_VSEL 0x23
+#define RK806_BUCK1_SLP_VSEL 0x24
+#define RK806_BUCK2_SLP_VSEL 0x25
+#define RK806_BUCK3_SLP_VSEL 0x26
+#define RK806_BUCK4_SLP_VSEL 0x27
+#define RK806_BUCK5_SLP_VSEL 0x28
+#define RK806_BUCK6_SLP_VSEL 0x29
+#define RK806_BUCK7_SLP_VSEL 0x2A
+#define RK806_BUCK8_SLP_VSEL 0x2B
+#define RK806_BUCK9_SLP_VSEL 0x2D
+#define RK806_BUCK10_SLP_VSEL 0x2E
+#define RK806_BUCK_DEBUG1 0x30
+#define RK806_BUCK_DEBUG2 0x31
+#define RK806_BUCK_DEBUG3 0x32
+#define RK806_BUCK_DEBUG4 0x33
+#define RK806_BUCK_DEBUG5 0x34
+#define RK806_BUCK_DEBUG6 0x35
+#define RK806_BUCK_DEBUG7 0x36
+#define RK806_BUCK_DEBUG8 0x37
+#define RK806_BUCK_DEBUG9 0x38
+#define RK806_BUCK_DEBUG10 0x39
+#define RK806_BUCK_DEBUG11 0x3A
+#define RK806_BUCK_DEBUG12 0x3B
+#define RK806_BUCK_DEBUG13 0x3C
+#define RK806_BUCK_DEBUG14 0x3D
+#define RK806_BUCK_DEBUG15 0x3E
+#define RK806_BUCK_DEBUG16 0x3F
+#define RK806_BUCK_DEBUG17 0x40
+#define RK806_BUCK_DEBUG18 0x41
+#define RK806_NLDO_IMAX 0x42
+#define RK806_NLDO1_ON_VSEL 0x43
+#define RK806_NLDO2_ON_VSEL 0x44
+#define RK806_NLDO3_ON_VSEL 0x45
+#define RK806_NLDO4_ON_VSEL 0x46
+#define RK806_NLDO5_ON_VSEL 0x47
+#define RK806_NLDO1_SLP_VSEL 0x48
+#define RK806_NLDO2_SLP_VSEL 0x49
+#define RK806_NLDO3_SLP_VSEL 0x4A
+#define RK806_NLDO4_SLP_VSEL 0x4B
+#define RK806_NLDO5_SLP_VSEL 0x4C
+#define RK806_PLDO_IMAX 0x4D
+#define RK806_PLDO1_ON_VSEL 0x4E
+#define RK806_PLDO2_ON_VSEL 0x4F
+#define RK806_PLDO3_ON_VSEL 0x50
+#define RK806_PLDO4_ON_VSEL 0x51
+#define RK806_PLDO5_ON_VSEL 0x52
+#define RK806_PLDO6_ON_VSEL 0x53
+#define RK806_PLDO1_SLP_VSEL 0x54
+#define RK806_PLDO2_SLP_VSEL 0x55
+#define RK806_PLDO3_SLP_VSEL 0x56
+#define RK806_PLDO4_SLP_VSEL 0x57
+#define RK806_PLDO5_SLP_VSEL 0x58
+#define RK806_PLDO6_SLP_VSEL 0x59
+#define RK806_CHIP_NAME 0x5A
+#define RK806_CHIP_VER 0x5B
+#define RK806_OTP_VER 0x5C
+#define RK806_SYS_STS 0x5D
+#define RK806_SYS_CFG0 0x5E
+#define RK806_SYS_CFG1 0x5F
+#define RK806_SYS_OPTION 0x61
+#define RK806_SLEEP_CONFIG0 0x62
+#define RK806_SLEEP_CONFIG1 0x63
+#define RK806_SLEEP_CTR_SEL0 0x64
+#define RK806_SLEEP_CTR_SEL1 0x65
+#define RK806_SLEEP_CTR_SEL2 0x66
+#define RK806_SLEEP_CTR_SEL3 0x67
+#define RK806_SLEEP_CTR_SEL4 0x68
+#define RK806_SLEEP_CTR_SEL5 0x69
+#define RK806_DVS_CTRL_SEL0 0x6A
+#define RK806_DVS_CTRL_SEL1 0x6B
+#define RK806_DVS_CTRL_SEL2 0x6C
+#define RK806_DVS_CTRL_SEL3 0x6D
+#define RK806_DVS_CTRL_SEL4 0x6E
+#define RK806_DVS_CTRL_SEL5 0x6F
+#define RK806_DVS_START_CTRL 0x70
+#define RK806_SLEEP_GPIO 0x71
+#define RK806_SYS_CFG3 0x72
+#define RK806_ON_SOURCE 0x74
+#define RK806_OFF_SOURCE 0x75
+#define RK806_PWRON_KEY 0x76
+#define RK806_INT_STS0 0x77
+#define RK806_INT_MSK0 0x78
+#define RK806_INT_STS1 0x79
+#define RK806_INT_MSK1 0x7A
+#define RK806_GPIO_INT_CONFIG 0x7B
+#define RK806_DATA_REG0 0x7C
+#define RK806_DATA_REG1 0x7D
+#define RK806_DATA_REG2 0x7E
+#define RK806_DATA_REG3 0x7F
+#define RK806_DATA_REG4 0x80
+#define RK806_DATA_REG5 0x81
+#define RK806_DATA_REG6 0x82
+#define RK806_DATA_REG7 0x83
+#define RK806_DATA_REG8 0x84
+#define RK806_DATA_REG9 0x85
+#define RK806_DATA_REG10 0x86
+#define RK806_DATA_REG11 0x87
+#define RK806_DATA_REG12 0x88
+#define RK806_DATA_REG13 0x89
+#define RK806_DATA_REG14 0x8A
+#define RK806_DATA_REG15 0x8B
+#define RK806_TM_REG 0x8C
+#define RK806_OTP_EN_REG 0x8D
+#define RK806_FUNC_OTP_EN_REG 0x8E
+#define RK806_TEST_REG1 0x8F
+#define RK806_TEST_REG2 0x90
+#define RK806_TEST_REG3 0x91
+#define RK806_TEST_REG4 0x92
+#define RK806_TEST_REG5 0x93
+#define RK806_BUCK_VSEL_OTP_REG0 0x94
+#define RK806_BUCK_VSEL_OTP_REG1 0x95
+#define RK806_BUCK_VSEL_OTP_REG2 0x96
+#define RK806_BUCK_VSEL_OTP_REG3 0x97
+#define RK806_BUCK_VSEL_OTP_REG4 0x98
+#define RK806_BUCK_VSEL_OTP_REG5 0x99
+#define RK806_BUCK_VSEL_OTP_REG6 0x9A
+#define RK806_BUCK_VSEL_OTP_REG7 0x9B
+#define RK806_BUCK_VSEL_OTP_REG8 0x9C
+#define RK806_BUCK_VSEL_OTP_REG9 0x9D
+#define RK806_NLDO1_VSEL_OTP_REG0 0x9E
+#define RK806_NLDO1_VSEL_OTP_REG1 0x9F
+#define RK806_NLDO1_VSEL_OTP_REG2 0xA0
+#define RK806_NLDO1_VSEL_OTP_REG3 0xA1
+#define RK806_NLDO1_VSEL_OTP_REG4 0xA2
+#define RK806_PLDO_VSEL_OTP_REG0 0xA3
+#define RK806_PLDO_VSEL_OTP_REG1 0xA4
+#define RK806_PLDO_VSEL_OTP_REG2 0xA5
+#define RK806_PLDO_VSEL_OTP_REG3 0xA6
+#define RK806_PLDO_VSEL_OTP_REG4 0xA7
+#define RK806_PLDO_VSEL_OTP_REG5 0xA8
+#define RK806_BUCK_EN_OTP_REG1 0xA9
+#define RK806_NLDO_EN_OTP_REG1 0xAA
+#define RK806_PLDO_EN_OTP_REG1 0xAB
+#define RK806_BUCK_FB_RES_OTP_REG1 0xAC
+#define RK806_OTP_RESEV_REG0 0xAD
+#define RK806_OTP_RESEV_REG1 0xAE
+#define RK806_OTP_RESEV_REG2 0xAF
+#define RK806_OTP_RESEV_REG3 0xB0
+#define RK806_OTP_RESEV_REG4 0xB1
+#define RK806_BUCK_SEQ_REG0 0xB2
+#define RK806_BUCK_SEQ_REG1 0xB3
+#define RK806_BUCK_SEQ_REG2 0xB4
+#define RK806_BUCK_SEQ_REG3 0xB5
+#define RK806_BUCK_SEQ_REG4 0xB6
+#define RK806_BUCK_SEQ_REG5 0xB7
+#define RK806_BUCK_SEQ_REG6 0xB8
+#define RK806_BUCK_SEQ_REG7 0xB9
+#define RK806_BUCK_SEQ_REG8 0xBA
+#define RK806_BUCK_SEQ_REG9 0xBB
+#define RK806_BUCK_SEQ_REG10 0xBC
+#define RK806_BUCK_SEQ_REG11 0xBD
+#define RK806_BUCK_SEQ_REG12 0xBE
+#define RK806_BUCK_SEQ_REG13 0xBF
+#define RK806_BUCK_SEQ_REG14 0xC0
+#define RK806_BUCK_SEQ_REG15 0xC1
+#define RK806_BUCK_SEQ_REG16 0xC2
+#define RK806_BUCK_SEQ_REG17 0xC3
+#define RK806_HK_TRIM_REG1 0xC4
+#define RK806_HK_TRIM_REG2 0xC5
+#define RK806_BUCK_REF_TRIM_REG1 0xC6
+#define RK806_BUCK_REF_TRIM_REG2 0xC7
+#define RK806_BUCK_REF_TRIM_REG3 0xC8
+#define RK806_BUCK_REF_TRIM_REG4 0xC9
+#define RK806_BUCK_REF_TRIM_REG5 0xCA
+#define RK806_BUCK_OSC_TRIM_REG1 0xCB
+#define RK806_BUCK_OSC_TRIM_REG2 0xCC
+#define RK806_BUCK_OSC_TRIM_REG3 0xCD
+#define RK806_BUCK_OSC_TRIM_REG4 0xCE
+#define RK806_BUCK_OSC_TRIM_REG5 0xCF
+#define RK806_BUCK_TRIM_ZCDIOS_REG1 0xD0
+#define RK806_BUCK_TRIM_ZCDIOS_REG2 0xD1
+#define RK806_NLDO_TRIM_REG1 0xD2
+#define RK806_NLDO_TRIM_REG2 0xD3
+#define RK806_NLDO_TRIM_REG3 0xD4
+#define RK806_PLDO_TRIM_REG1 0xD5
+#define RK806_PLDO_TRIM_REG2 0xD6
+#define RK806_PLDO_TRIM_REG3 0xD7
+#define RK806_TRIM_ICOMP_REG1 0xD8
+#define RK806_TRIM_ICOMP_REG2 0xD9
+#define RK806_EFUSE_CONTROL_REGH 0xDA
+#define RK806_FUSE_PROG_REG 0xDB
+#define RK806_MAIN_FSM_STS_REG 0xDD
+#define RK806_FSM_REG 0xDE
+#define RK806_TOP_RESEV_OFFR 0xEC
+#define RK806_TOP_RESEV_POR 0xED
+#define RK806_BUCK_VRSN_REG1 0xEE
+#define RK806_BUCK_VRSN_REG2 0xEF
+#define RK806_NLDO_RLOAD_SEL_REG1 0xF0
+#define RK806_PLDO_RLOAD_SEL_REG1 0xF1
+#define RK806_PLDO_RLOAD_SEL_REG2 0xF2
+#define RK806_BUCK_CMIN_MX_REG1 0xF3
+#define RK806_BUCK_CMIN_MX_REG2 0xF4
+#define RK806_BUCK_FREQ_SET_REG1 0xF5
+#define RK806_BUCK_FREQ_SET_REG2 0xF6
+#define RK806_BUCK_RS_MEABS_REG1 0xF7
+#define RK806_BUCK_RS_MEABS_REG2 0xF8
+#define RK806_BUCK_RS_ZDLEB_REG1 0xF9
+#define RK806_BUCK_RS_ZDLEB_REG2 0xFA
+#define RK806_BUCK_RSERVE_REG1 0xFB
+#define RK806_BUCK_RSERVE_REG2 0xFC
+#define RK806_BUCK_RSERVE_REG3 0xFD
+#define RK806_BUCK_RSERVE_REG4 0xFE
+#define RK806_BUCK_RSERVE_REG5 0xFF
+
+/* INT_STS Register field definitions */
+#define RK806_INT_STS_PWRON_FALL BIT(0)
+#define RK806_INT_STS_PWRON_RISE BIT(1)
+#define RK806_INT_STS_PWRON BIT(2)
+#define RK806_INT_STS_PWRON_LP BIT(3)
+#define RK806_INT_STS_HOTDIE BIT(4)
+#define RK806_INT_STS_VDC_RISE BIT(5)
+#define RK806_INT_STS_VDC_FALL BIT(6)
+#define RK806_INT_STS_VB_LO BIT(7)
+#define RK806_INT_STS_REV0 BIT(0)
+#define RK806_INT_STS_REV1 BIT(1)
+#define RK806_INT_STS_REV2 BIT(2)
+#define RK806_INT_STS_CRC_ERROR BIT(3)
+#define RK806_INT_STS_SLP3_GPIO BIT(4)
+#define RK806_INT_STS_SLP2_GPIO BIT(5)
+#define RK806_INT_STS_SLP1_GPIO BIT(6)
+#define RK806_INT_STS_WDT BIT(7)
+
+/* SPI command */
+#define RK806_CMD_READ 0
+#define RK806_CMD_WRITE BIT(7)
+#define RK806_CMD_CRC_EN BIT(6)
+#define RK806_CMD_CRC_DIS 0
+#define RK806_CMD_LEN_MSK 0x0f
+#define RK806_REG_H 0x00
+
+#define VERSION_AB 0x01
+
+enum rk806_reg_id {
+ RK806_ID_DCDC1 = 0,
+ RK806_ID_DCDC2,
+ RK806_ID_DCDC3,
+ RK806_ID_DCDC4,
+ RK806_ID_DCDC5,
+ RK806_ID_DCDC6,
+ RK806_ID_DCDC7,
+ RK806_ID_DCDC8,
+ RK806_ID_DCDC9,
+ RK806_ID_DCDC10,
+
+ RK806_ID_NLDO1,
+ RK806_ID_NLDO2,
+ RK806_ID_NLDO3,
+ RK806_ID_NLDO4,
+ RK806_ID_NLDO5,
+
+ RK806_ID_PLDO1,
+ RK806_ID_PLDO2,
+ RK806_ID_PLDO3,
+ RK806_ID_PLDO4,
+ RK806_ID_PLDO5,
+ RK806_ID_PLDO6,
+ RK806_ID_END,
+};
+
+/* Define the RK806 IRQ numbers */
+enum rk806_irqs {
+ /* INT_STS0 registers */
+ RK806_IRQ_PWRON_FALL,
+ RK806_IRQ_PWRON_RISE,
+ RK806_IRQ_PWRON,
+ RK806_IRQ_PWRON_LP,
+ RK806_IRQ_HOTDIE,
+ RK806_IRQ_VDC_RISE,
+ RK806_IRQ_VDC_FALL,
+ RK806_IRQ_VB_LO,
+
+ /* INT_STS0 registers */
+ RK806_IRQ_REV0,
+ RK806_IRQ_REV1,
+ RK806_IRQ_REV2,
+ RK806_IRQ_CRC_ERROR,
+ RK806_IRQ_SLP3_GPIO,
+ RK806_IRQ_SLP2_GPIO,
+ RK806_IRQ_SLP1_GPIO,
+ RK806_IRQ_WDT,
+};
+
+/* VCC1 Low Voltage Threshold */
+enum rk806_lv_sel {
+ VB_LO_SEL_2800,
+ VB_LO_SEL_2900,
+ VB_LO_SEL_3000,
+ VB_LO_SEL_3100,
+ VB_LO_SEL_3200,
+ VB_LO_SEL_3300,
+ VB_LO_SEL_3400,
+ VB_LO_SEL_3500,
+};
+
+/* System Shutdown Voltage Select */
+enum rk806_uv_sel {
+ VB_UV_SEL_2700,
+ VB_UV_SEL_2800,
+ VB_UV_SEL_2900,
+ VB_UV_SEL_3000,
+ VB_UV_SEL_3100,
+ VB_UV_SEL_3200,
+ VB_UV_SEL_3300,
+ VB_UV_SEL_3400,
+};
+
+/* Pin Function */
+enum rk806_pwrctrl_fun {
+ PWRCTRL_NULL_FUN,
+ PWRCTRL_SLP_FUN,
+ PWRCTRL_POWOFF_FUN,
+ PWRCTRL_RST_FUN,
+ PWRCTRL_DVS_FUN,
+ PWRCTRL_GPIO_FUN,
+};
+
+/* Pin Polarity */
+enum rk806_pin_level {
+ POL_LOW,
+ POL_HIGH,
+};
+
+enum rk806_vsel_ctr_sel {
+ CTR_BY_NO_EFFECT,
+ CTR_BY_PWRCTRL1,
+ CTR_BY_PWRCTRL2,
+ CTR_BY_PWRCTRL3,
+};
+
+enum rk806_dvs_ctr_sel {
+ CTR_SEL_NO_EFFECT,
+ CTR_SEL_DVS_START1,
+ CTR_SEL_DVS_START2,
+ CTR_SEL_DVS_START3,
+};
+
+enum rk806_pin_dr_sel {
+ RK806_PIN_INPUT,
+ RK806_PIN_OUTPUT,
+};
+
+#define RK806_INT_POL_MSK BIT(1)
+#define RK806_INT_POL_H BIT(1)
+#define RK806_INT_POL_L 0
+
+#define RK806_SLAVE_RESTART_FUN_MSK BIT(1)
+#define RK806_SLAVE_RESTART_FUN_EN BIT(1)
+#define RK806_SLAVE_RESTART_FUN_OFF 0
+
+#define RK806_SYS_ENB2_2M_MSK BIT(1)
+#define RK806_SYS_ENB2_2M_EN BIT(1)
+#define RK806_SYS_ENB2_2M_OFF 0
+
+enum rk806_int_fun {
+ RK806_INT_ONLY,
+ RK806_INT_ADN_WKUP,
+};
+
+enum rk806_dvs_mode {
+ RK806_DVS_NOT_SUPPORT,
+ RK806_DVS_START1,
+ RK806_DVS_START2,
+ RK806_DVS_START3,
+ RK806_DVS_PWRCTRL1,
+ RK806_DVS_PWRCTRL2,
+ RK806_DVS_PWRCTRL3,
+ RK806_DVS_START_PWRCTR1,
+ RK806_DVS_START_PWRCTR2,
+ RK806_DVS_START_PWRCTR3,
+ RK806_DVS_END,
+};
+
/* RK808 IRQ Definitions */
#define RK808_IRQ_VOUT_LO 0
#define RK808_IRQ_VB_LO 1
@@ -780,6 +1188,7 @@ enum {
enum {
RK805_ID = 0x8050,
+ RK806_ID = 0x8060,
RK808_ID = 0x0000,
RK809_ID = 0x8090,
RK817_ID = 0x8170,
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 10/13] pinctrl: rk805: add rk806 pinctrl support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel, shengfei Xu
Add support for rk806 dvs pinctrl to the existing rk805
driver.
This has been implemented using shengfei Xu's rk806
specific driver from the vendor tree as reference.
Co-Developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/pinctrl/pinctrl-rk805.c | 189 ++++++++++++++++++++++++++++----
1 file changed, 168 insertions(+), 21 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-rk805.c b/drivers/pinctrl/pinctrl-rk805.c
index 7c1f7408fb9a..2639a9ee82cd 100644
--- a/drivers/pinctrl/pinctrl-rk805.c
+++ b/drivers/pinctrl/pinctrl-rk805.c
@@ -1,10 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later
/*
- * Pinctrl driver for Rockchip RK805 PMIC
+ * Pinctrl driver for Rockchip RK805/RK806 PMIC
*
* Copyright (c) 2017, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
*
* Author: Joseph Chen <chenjh@rock-chips.com>
+ * Author: Xu Shengfei <xsf@rock-chips.com>
*
* Based on the pinctrl-as3722 driver
*/
@@ -44,6 +46,7 @@ struct rk805_pin_group {
/*
* @reg: gpio setting register;
+ * @fun_reg: functions select register;
* @fun_mask: functions select mask value, when set is gpio;
* @dir_mask: input or output mask value, when set is output, otherwise input;
* @val_mask: gpio set value, when set is level high, otherwise low;
@@ -56,6 +59,7 @@ struct rk805_pin_group {
*/
struct rk805_pin_config {
u8 reg;
+ u8 fun_reg;
u8 fun_msk;
u8 dir_msk;
u8 val_msk;
@@ -80,22 +84,50 @@ enum rk805_pinmux_option {
RK805_PINMUX_GPIO,
};
+enum rk806_pinmux_option {
+ RK806_PINMUX_FUN0 = 0,
+ RK806_PINMUX_FUN1,
+ RK806_PINMUX_FUN2,
+ RK806_PINMUX_FUN3,
+ RK806_PINMUX_FUN4,
+ RK806_PINMUX_FUN5,
+};
+
enum {
RK805_GPIO0,
RK805_GPIO1,
};
+enum {
+ RK806_GPIO_DVS1,
+ RK806_GPIO_DVS2,
+ RK806_GPIO_DVS3
+};
+
static const char *const rk805_gpio_groups[] = {
"gpio0",
"gpio1",
};
+static const char *const rk806_gpio_groups[] = {
+ "gpio_pwrctrl1",
+ "gpio_pwrctrl2",
+ "gpio_pwrctrl3",
+};
+
/* RK805: 2 output only GPIOs */
static const struct pinctrl_pin_desc rk805_pins_desc[] = {
PINCTRL_PIN(RK805_GPIO0, "gpio0"),
PINCTRL_PIN(RK805_GPIO1, "gpio1"),
};
+/* RK806 */
+static const struct pinctrl_pin_desc rk806_pins_desc[] = {
+ PINCTRL_PIN(RK806_GPIO_DVS1, "gpio_pwrctrl1"),
+ PINCTRL_PIN(RK806_GPIO_DVS2, "gpio_pwrctrl2"),
+ PINCTRL_PIN(RK806_GPIO_DVS3, "gpio_pwrctrl3"),
+};
+
static const struct rk805_pin_function rk805_pin_functions[] = {
{
.name = "gpio",
@@ -105,6 +137,45 @@ static const struct rk805_pin_function rk805_pin_functions[] = {
},
};
+static const struct rk805_pin_function rk806_pin_functions[] = {
+ {
+ .name = "pin_fun0",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN0,
+ },
+ {
+ .name = "pin_fun1",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN1,
+ },
+ {
+ .name = "pin_fun2",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN2,
+ },
+ {
+ .name = "pin_fun3",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN3,
+ },
+ {
+ .name = "pin_fun4",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN4,
+ },
+ {
+ .name = "pin_fun5",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN5,
+ },
+};
+
static const struct rk805_pin_group rk805_pin_groups[] = {
{
.name = "gpio0",
@@ -118,6 +189,24 @@ static const struct rk805_pin_group rk805_pin_groups[] = {
},
};
+static const struct rk805_pin_group rk806_pin_groups[] = {
+ {
+ .name = "gpio_pwrctrl1",
+ .pins = { RK806_GPIO_DVS1 },
+ .npins = 1,
+ },
+ {
+ .name = "gpio_pwrctrl2",
+ .pins = { RK806_GPIO_DVS2 },
+ .npins = 1,
+ },
+ {
+ .name = "gpio_pwrctrl3",
+ .pins = { RK806_GPIO_DVS3 },
+ .npins = 1,
+ }
+};
+
#define RK805_GPIO0_VAL_MSK BIT(0)
#define RK805_GPIO1_VAL_MSK BIT(1)
@@ -132,6 +221,40 @@ static const struct rk805_pin_config rk805_gpio_cfgs[] = {
},
};
+#define RK806_PWRCTRL1_DR BIT(0)
+#define RK806_PWRCTRL2_DR BIT(1)
+#define RK806_PWRCTRL3_DR BIT(2)
+#define RK806_PWRCTRL1_DATA BIT(4)
+#define RK806_PWRCTRL2_DATA BIT(5)
+#define RK806_PWRCTRL3_DATA BIT(6)
+#define RK806_PWRCTRL1_FUN GENMASK(2, 0)
+#define RK806_PWRCTRL2_FUN GENMASK(6, 4)
+#define RK806_PWRCTRL3_FUN GENMASK(2, 0)
+
+static struct rk805_pin_config rk806_gpio_cfgs[] = {
+ {
+ .fun_reg = RK806_SLEEP_CONFIG0,
+ .fun_msk = RK806_PWRCTRL1_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL1_DATA,
+ .dir_msk = RK806_PWRCTRL1_DR,
+ },
+ {
+ .fun_reg = RK806_SLEEP_CONFIG0,
+ .fun_msk = RK806_PWRCTRL2_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL2_DATA,
+ .dir_msk = RK806_PWRCTRL2_DR,
+ },
+ {
+ .fun_reg = RK806_SLEEP_CONFIG1,
+ .fun_msk = RK806_PWRCTRL3_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL3_DATA,
+ .dir_msk = RK806_PWRCTRL3_DR,
+ }
+};
+
/* generic gpio chip */
static int rk805_gpio_get(struct gpio_chip *chip, unsigned int offset)
{
@@ -289,19 +412,13 @@ static int _rk805_pinctrl_set_mux(struct pinctrl_dev *pctldev,
if (!pci->pin_cfg[offset].fun_msk)
return 0;
- if (mux == RK805_PINMUX_GPIO) {
- ret = regmap_update_bits(pci->rk808->regmap,
- pci->pin_cfg[offset].reg,
- pci->pin_cfg[offset].fun_msk,
- pci->pin_cfg[offset].fun_msk);
- if (ret) {
- dev_err(pci->dev, "set gpio%d GPIO failed\n", offset);
- return ret;
- }
- } else {
- dev_err(pci->dev, "Couldn't find function mux %d\n", mux);
- return -EINVAL;
- }
+ mux <<= ffs(pci->pin_cfg[offset].fun_msk) - 1;
+ ret = regmap_update_bits(pci->rk808->regmap,
+ pci->pin_cfg[offset].fun_reg,
+ pci->pin_cfg[offset].fun_msk, mux);
+
+ if (ret)
+ dev_err(pci->dev, "set gpio%d func%d failed\n", offset, mux);
return 0;
}
@@ -317,6 +434,22 @@ static int rk805_pinctrl_set_mux(struct pinctrl_dev *pctldev,
return _rk805_pinctrl_set_mux(pctldev, offset, mux);
}
+static int rk805_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int offset)
+{
+ struct rk805_pctrl_info *pci = pinctrl_dev_get_drvdata(pctldev);
+
+ switch (pci->rk808->variant) {
+ case RK805_ID:
+ return _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
+ case RK806_ID:
+ return _rk805_pinctrl_set_mux(pctldev, offset, RK806_PINMUX_FUN5);
+ }
+
+ return -ENOTSUPP;
+}
+
static int rk805_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct pinctrl_gpio_range *range,
unsigned int offset, bool input)
@@ -324,13 +457,6 @@ static int rk805_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct rk805_pctrl_info *pci = pinctrl_dev_get_drvdata(pctldev);
int ret;
- /* switch to gpio function */
- ret = _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
- if (ret) {
- dev_err(pci->dev, "set gpio%d mux failed\n", offset);
- return ret;
- }
-
/* set direction */
if (!pci->pin_cfg[offset].dir_msk)
return 0;
@@ -352,6 +478,7 @@ static const struct pinmux_ops rk805_pinmux_ops = {
.get_function_name = rk805_pinctrl_get_func_name,
.get_function_groups = rk805_pinctrl_get_func_groups,
.set_mux = rk805_pinctrl_set_mux,
+ .gpio_request_enable = rk805_pinctrl_gpio_request_enable,
.gpio_set_direction = rk805_pmx_gpio_set_direction,
};
@@ -364,6 +491,7 @@ static int rk805_pinconf_get(struct pinctrl_dev *pctldev,
switch (param) {
case PIN_CONFIG_OUTPUT:
+ case PIN_CONFIG_INPUT_ENABLE:
arg = rk805_gpio_get(&pci->gpio_chip, pin);
break;
default:
@@ -393,6 +521,12 @@ static int rk805_pinconf_set(struct pinctrl_dev *pctldev,
rk805_gpio_set(&pci->gpio_chip, pin, arg);
rk805_pmx_gpio_set_direction(pctldev, NULL, pin, false);
break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (pci->rk808->variant != RK805_ID && arg) {
+ rk805_pmx_gpio_set_direction(pctldev, NULL, pin, true);
+ break;
+ }
+ fallthrough;
default:
dev_err(pci->dev, "Properties not supported\n");
return -ENOTSUPP;
@@ -448,6 +582,18 @@ static int rk805_pinctrl_probe(struct platform_device *pdev)
pci->pin_cfg = rk805_gpio_cfgs;
pci->gpio_chip.ngpio = ARRAY_SIZE(rk805_gpio_cfgs);
break;
+ case RK806_ID:
+ pci->pins = rk806_pins_desc;
+ pci->num_pins = ARRAY_SIZE(rk806_pins_desc);
+ pci->functions = rk806_pin_functions;
+ pci->num_functions = ARRAY_SIZE(rk806_pin_functions);
+ pci->groups = rk806_pin_groups;
+ pci->num_pin_groups = ARRAY_SIZE(rk806_pin_groups);
+ pci->pinctrl_desc.pins = rk806_pins_desc;
+ pci->pinctrl_desc.npins = ARRAY_SIZE(rk806_pins_desc);
+ pci->pin_cfg = rk806_gpio_cfgs;
+ pci->gpio_chip.ngpio = ARRAY_SIZE(rk806_gpio_cfgs);
+ break;
default:
dev_err(&pdev->dev, "unsupported RK805 ID %lu\n",
pci->rk808->variant);
@@ -488,5 +634,6 @@ static struct platform_driver rk805_pinctrl_driver = {
module_platform_driver(rk805_pinctrl_driver);
MODULE_DESCRIPTION("RK805 pin control and GPIO driver");
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
MODULE_AUTHOR("Joseph Chen <chenjh@rock-chips.com>");
MODULE_LICENSE("GPL v2");
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 10/13] pinctrl: rk805: add rk806 pinctrl support
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel, shengfei Xu
Add support for rk806 dvs pinctrl to the existing rk805
driver.
This has been implemented using shengfei Xu's rk806
specific driver from the vendor tree as reference.
Co-Developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/pinctrl/pinctrl-rk805.c | 189 ++++++++++++++++++++++++++++----
1 file changed, 168 insertions(+), 21 deletions(-)
diff --git a/drivers/pinctrl/pinctrl-rk805.c b/drivers/pinctrl/pinctrl-rk805.c
index 7c1f7408fb9a..2639a9ee82cd 100644
--- a/drivers/pinctrl/pinctrl-rk805.c
+++ b/drivers/pinctrl/pinctrl-rk805.c
@@ -1,10 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later
/*
- * Pinctrl driver for Rockchip RK805 PMIC
+ * Pinctrl driver for Rockchip RK805/RK806 PMIC
*
* Copyright (c) 2017, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
*
* Author: Joseph Chen <chenjh@rock-chips.com>
+ * Author: Xu Shengfei <xsf@rock-chips.com>
*
* Based on the pinctrl-as3722 driver
*/
@@ -44,6 +46,7 @@ struct rk805_pin_group {
/*
* @reg: gpio setting register;
+ * @fun_reg: functions select register;
* @fun_mask: functions select mask value, when set is gpio;
* @dir_mask: input or output mask value, when set is output, otherwise input;
* @val_mask: gpio set value, when set is level high, otherwise low;
@@ -56,6 +59,7 @@ struct rk805_pin_group {
*/
struct rk805_pin_config {
u8 reg;
+ u8 fun_reg;
u8 fun_msk;
u8 dir_msk;
u8 val_msk;
@@ -80,22 +84,50 @@ enum rk805_pinmux_option {
RK805_PINMUX_GPIO,
};
+enum rk806_pinmux_option {
+ RK806_PINMUX_FUN0 = 0,
+ RK806_PINMUX_FUN1,
+ RK806_PINMUX_FUN2,
+ RK806_PINMUX_FUN3,
+ RK806_PINMUX_FUN4,
+ RK806_PINMUX_FUN5,
+};
+
enum {
RK805_GPIO0,
RK805_GPIO1,
};
+enum {
+ RK806_GPIO_DVS1,
+ RK806_GPIO_DVS2,
+ RK806_GPIO_DVS3
+};
+
static const char *const rk805_gpio_groups[] = {
"gpio0",
"gpio1",
};
+static const char *const rk806_gpio_groups[] = {
+ "gpio_pwrctrl1",
+ "gpio_pwrctrl2",
+ "gpio_pwrctrl3",
+};
+
/* RK805: 2 output only GPIOs */
static const struct pinctrl_pin_desc rk805_pins_desc[] = {
PINCTRL_PIN(RK805_GPIO0, "gpio0"),
PINCTRL_PIN(RK805_GPIO1, "gpio1"),
};
+/* RK806 */
+static const struct pinctrl_pin_desc rk806_pins_desc[] = {
+ PINCTRL_PIN(RK806_GPIO_DVS1, "gpio_pwrctrl1"),
+ PINCTRL_PIN(RK806_GPIO_DVS2, "gpio_pwrctrl2"),
+ PINCTRL_PIN(RK806_GPIO_DVS3, "gpio_pwrctrl3"),
+};
+
static const struct rk805_pin_function rk805_pin_functions[] = {
{
.name = "gpio",
@@ -105,6 +137,45 @@ static const struct rk805_pin_function rk805_pin_functions[] = {
},
};
+static const struct rk805_pin_function rk806_pin_functions[] = {
+ {
+ .name = "pin_fun0",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN0,
+ },
+ {
+ .name = "pin_fun1",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN1,
+ },
+ {
+ .name = "pin_fun2",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN2,
+ },
+ {
+ .name = "pin_fun3",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN3,
+ },
+ {
+ .name = "pin_fun4",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN4,
+ },
+ {
+ .name = "pin_fun5",
+ .groups = rk806_gpio_groups,
+ .ngroups = ARRAY_SIZE(rk806_gpio_groups),
+ .mux_option = RK806_PINMUX_FUN5,
+ },
+};
+
static const struct rk805_pin_group rk805_pin_groups[] = {
{
.name = "gpio0",
@@ -118,6 +189,24 @@ static const struct rk805_pin_group rk805_pin_groups[] = {
},
};
+static const struct rk805_pin_group rk806_pin_groups[] = {
+ {
+ .name = "gpio_pwrctrl1",
+ .pins = { RK806_GPIO_DVS1 },
+ .npins = 1,
+ },
+ {
+ .name = "gpio_pwrctrl2",
+ .pins = { RK806_GPIO_DVS2 },
+ .npins = 1,
+ },
+ {
+ .name = "gpio_pwrctrl3",
+ .pins = { RK806_GPIO_DVS3 },
+ .npins = 1,
+ }
+};
+
#define RK805_GPIO0_VAL_MSK BIT(0)
#define RK805_GPIO1_VAL_MSK BIT(1)
@@ -132,6 +221,40 @@ static const struct rk805_pin_config rk805_gpio_cfgs[] = {
},
};
+#define RK806_PWRCTRL1_DR BIT(0)
+#define RK806_PWRCTRL2_DR BIT(1)
+#define RK806_PWRCTRL3_DR BIT(2)
+#define RK806_PWRCTRL1_DATA BIT(4)
+#define RK806_PWRCTRL2_DATA BIT(5)
+#define RK806_PWRCTRL3_DATA BIT(6)
+#define RK806_PWRCTRL1_FUN GENMASK(2, 0)
+#define RK806_PWRCTRL2_FUN GENMASK(6, 4)
+#define RK806_PWRCTRL3_FUN GENMASK(2, 0)
+
+static struct rk805_pin_config rk806_gpio_cfgs[] = {
+ {
+ .fun_reg = RK806_SLEEP_CONFIG0,
+ .fun_msk = RK806_PWRCTRL1_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL1_DATA,
+ .dir_msk = RK806_PWRCTRL1_DR,
+ },
+ {
+ .fun_reg = RK806_SLEEP_CONFIG0,
+ .fun_msk = RK806_PWRCTRL2_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL2_DATA,
+ .dir_msk = RK806_PWRCTRL2_DR,
+ },
+ {
+ .fun_reg = RK806_SLEEP_CONFIG1,
+ .fun_msk = RK806_PWRCTRL3_FUN,
+ .reg = RK806_SLEEP_GPIO,
+ .val_msk = RK806_PWRCTRL3_DATA,
+ .dir_msk = RK806_PWRCTRL3_DR,
+ }
+};
+
/* generic gpio chip */
static int rk805_gpio_get(struct gpio_chip *chip, unsigned int offset)
{
@@ -289,19 +412,13 @@ static int _rk805_pinctrl_set_mux(struct pinctrl_dev *pctldev,
if (!pci->pin_cfg[offset].fun_msk)
return 0;
- if (mux == RK805_PINMUX_GPIO) {
- ret = regmap_update_bits(pci->rk808->regmap,
- pci->pin_cfg[offset].reg,
- pci->pin_cfg[offset].fun_msk,
- pci->pin_cfg[offset].fun_msk);
- if (ret) {
- dev_err(pci->dev, "set gpio%d GPIO failed\n", offset);
- return ret;
- }
- } else {
- dev_err(pci->dev, "Couldn't find function mux %d\n", mux);
- return -EINVAL;
- }
+ mux <<= ffs(pci->pin_cfg[offset].fun_msk) - 1;
+ ret = regmap_update_bits(pci->rk808->regmap,
+ pci->pin_cfg[offset].fun_reg,
+ pci->pin_cfg[offset].fun_msk, mux);
+
+ if (ret)
+ dev_err(pci->dev, "set gpio%d func%d failed\n", offset, mux);
return 0;
}
@@ -317,6 +434,22 @@ static int rk805_pinctrl_set_mux(struct pinctrl_dev *pctldev,
return _rk805_pinctrl_set_mux(pctldev, offset, mux);
}
+static int rk805_pinctrl_gpio_request_enable(struct pinctrl_dev *pctldev,
+ struct pinctrl_gpio_range *range,
+ unsigned int offset)
+{
+ struct rk805_pctrl_info *pci = pinctrl_dev_get_drvdata(pctldev);
+
+ switch (pci->rk808->variant) {
+ case RK805_ID:
+ return _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
+ case RK806_ID:
+ return _rk805_pinctrl_set_mux(pctldev, offset, RK806_PINMUX_FUN5);
+ }
+
+ return -ENOTSUPP;
+}
+
static int rk805_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct pinctrl_gpio_range *range,
unsigned int offset, bool input)
@@ -324,13 +457,6 @@ static int rk805_pmx_gpio_set_direction(struct pinctrl_dev *pctldev,
struct rk805_pctrl_info *pci = pinctrl_dev_get_drvdata(pctldev);
int ret;
- /* switch to gpio function */
- ret = _rk805_pinctrl_set_mux(pctldev, offset, RK805_PINMUX_GPIO);
- if (ret) {
- dev_err(pci->dev, "set gpio%d mux failed\n", offset);
- return ret;
- }
-
/* set direction */
if (!pci->pin_cfg[offset].dir_msk)
return 0;
@@ -352,6 +478,7 @@ static const struct pinmux_ops rk805_pinmux_ops = {
.get_function_name = rk805_pinctrl_get_func_name,
.get_function_groups = rk805_pinctrl_get_func_groups,
.set_mux = rk805_pinctrl_set_mux,
+ .gpio_request_enable = rk805_pinctrl_gpio_request_enable,
.gpio_set_direction = rk805_pmx_gpio_set_direction,
};
@@ -364,6 +491,7 @@ static int rk805_pinconf_get(struct pinctrl_dev *pctldev,
switch (param) {
case PIN_CONFIG_OUTPUT:
+ case PIN_CONFIG_INPUT_ENABLE:
arg = rk805_gpio_get(&pci->gpio_chip, pin);
break;
default:
@@ -393,6 +521,12 @@ static int rk805_pinconf_set(struct pinctrl_dev *pctldev,
rk805_gpio_set(&pci->gpio_chip, pin, arg);
rk805_pmx_gpio_set_direction(pctldev, NULL, pin, false);
break;
+ case PIN_CONFIG_INPUT_ENABLE:
+ if (pci->rk808->variant != RK805_ID && arg) {
+ rk805_pmx_gpio_set_direction(pctldev, NULL, pin, true);
+ break;
+ }
+ fallthrough;
default:
dev_err(pci->dev, "Properties not supported\n");
return -ENOTSUPP;
@@ -448,6 +582,18 @@ static int rk805_pinctrl_probe(struct platform_device *pdev)
pci->pin_cfg = rk805_gpio_cfgs;
pci->gpio_chip.ngpio = ARRAY_SIZE(rk805_gpio_cfgs);
break;
+ case RK806_ID:
+ pci->pins = rk806_pins_desc;
+ pci->num_pins = ARRAY_SIZE(rk806_pins_desc);
+ pci->functions = rk806_pin_functions;
+ pci->num_functions = ARRAY_SIZE(rk806_pin_functions);
+ pci->groups = rk806_pin_groups;
+ pci->num_pin_groups = ARRAY_SIZE(rk806_pin_groups);
+ pci->pinctrl_desc.pins = rk806_pins_desc;
+ pci->pinctrl_desc.npins = ARRAY_SIZE(rk806_pins_desc);
+ pci->pin_cfg = rk806_gpio_cfgs;
+ pci->gpio_chip.ngpio = ARRAY_SIZE(rk806_gpio_cfgs);
+ break;
default:
dev_err(&pdev->dev, "unsupported RK805 ID %lu\n",
pci->rk808->variant);
@@ -488,5 +634,6 @@ static struct platform_driver rk805_pinctrl_driver = {
module_platform_driver(rk805_pinctrl_driver);
MODULE_DESCRIPTION("RK805 pin control and GPIO driver");
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
MODULE_AUTHOR("Joseph Chen <chenjh@rock-chips.com>");
MODULE_LICENSE("GPL v2");
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 11/13] regulator: rk808: Use dev_err_probe
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Print error message for potential EPROBE_DEFER error using
dev_err_probe, which captures the reason in
/sys/kernel/debug/devices_deferred and otherwise silences
the message.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 8 +++-----
1 file changed, 3 insertions(+), 5 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index ce9c64cadeba..fa9fc1aa1ae3 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -1343,11 +1343,9 @@ static int rk808_regulator_probe(struct platform_device *pdev)
for (i = 0; i < nregulators; i++) {
rk808_rdev = devm_regulator_register(&pdev->dev,
®ulators[i], &config);
- if (IS_ERR(rk808_rdev)) {
- dev_err(&pdev->dev,
- "failed to register %d regulator\n", i);
- return PTR_ERR(rk808_rdev);
- }
+ if (IS_ERR(rk808_rdev))
+ return dev_err_probe(&pdev->dev, PTR_ERR(rk808_rdev),
+ "failed to register %d regulator\n", i);
}
return 0;
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 11/13] regulator: rk808: Use dev_err_probe
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Print error message for potential EPROBE_DEFER error using
dev_err_probe, which captures the reason in
/sys/kernel/debug/devices_deferred and otherwise silences
the message.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 8 +++-----
1 file changed, 3 insertions(+), 5 deletions(-)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index ce9c64cadeba..fa9fc1aa1ae3 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -1343,11 +1343,9 @@ static int rk808_regulator_probe(struct platform_device *pdev)
for (i = 0; i < nregulators; i++) {
rk808_rdev = devm_regulator_register(&pdev->dev,
®ulators[i], &config);
- if (IS_ERR(rk808_rdev)) {
- dev_err(&pdev->dev,
- "failed to register %d regulator\n", i);
- return PTR_ERR(rk808_rdev);
- }
+ if (IS_ERR(rk808_rdev))
+ return dev_err_probe(&pdev->dev, PTR_ERR(rk808_rdev),
+ "failed to register %d regulator\n", i);
}
return 0;
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 12/13] regulator: expose regulator_find_closest_bigger
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Expose and document the table lookup logic used by
regulator_set_ramp_delay_regmap, so that it can be
reused for devices that cannot be configured via
regulator_set_ramp_delay_regmap.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/helpers.c | 22 ++++++++++++++++++----
include/linux/regulator/driver.h | 2 ++
2 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index ad2237a95572..586f42e378ee 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -902,8 +902,21 @@ bool regulator_is_equal(struct regulator *reg1, struct regulator *reg2)
}
EXPORT_SYMBOL_GPL(regulator_is_equal);
-static int find_closest_bigger(unsigned int target, const unsigned int *table,
- unsigned int num_sel, unsigned int *sel)
+/**
+ * regulator_find_closest_bigger - helper to find offset in ramp delay table
+ *
+ * @target: targeted ramp_delay
+ * @table: table with supported ramp delays
+ * @num_sel: number of entries in the table
+ * @sel: Pointer to store table offset
+ *
+ * This is the internal helper used by regulator_set_ramp_delay_regmap to
+ * map ramp delay to register value. It should only be used directly if
+ * regulator_set_ramp_delay_regmap cannot handle a specific device setup
+ * (e.g. because the value is split over multiple registers).
+ */
+int regulator_find_closest_bigger(unsigned int target, const unsigned int *table,
+ unsigned int num_sel, unsigned int *sel)
{
unsigned int s, tmp, max, maxsel = 0;
bool found = false;
@@ -933,6 +946,7 @@ static int find_closest_bigger(unsigned int target, const unsigned int *table,
return 0;
}
+EXPORT_SYMBOL_GPL(regulator_find_closest_bigger);
/**
* regulator_set_ramp_delay_regmap - set_ramp_delay() helper
@@ -951,8 +965,8 @@ int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay)
if (WARN_ON(!rdev->desc->n_ramp_values || !rdev->desc->ramp_delay_table))
return -EINVAL;
- ret = find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
- rdev->desc->n_ramp_values, &sel);
+ ret = regulator_find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
+ rdev->desc->n_ramp_values, &sel);
if (ret) {
dev_warn(rdev_get_dev(rdev),
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index f9a7461e72b8..d6a3bb39d7dc 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -757,6 +757,8 @@ int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
int min_uA, int max_uA);
int regulator_get_current_limit_regmap(struct regulator_dev *rdev);
void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
+int regulator_find_closest_bigger(unsigned int target, const unsigned int *table,
+ unsigned int num_sel, unsigned int *sel);
int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay);
int regulator_sync_voltage_rdev(struct regulator_dev *rdev);
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 12/13] regulator: expose regulator_find_closest_bigger
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel
Expose and document the table lookup logic used by
regulator_set_ramp_delay_regmap, so that it can be
reused for devices that cannot be configured via
regulator_set_ramp_delay_regmap.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/helpers.c | 22 ++++++++++++++++++----
include/linux/regulator/driver.h | 2 ++
2 files changed, 20 insertions(+), 4 deletions(-)
diff --git a/drivers/regulator/helpers.c b/drivers/regulator/helpers.c
index ad2237a95572..586f42e378ee 100644
--- a/drivers/regulator/helpers.c
+++ b/drivers/regulator/helpers.c
@@ -902,8 +902,21 @@ bool regulator_is_equal(struct regulator *reg1, struct regulator *reg2)
}
EXPORT_SYMBOL_GPL(regulator_is_equal);
-static int find_closest_bigger(unsigned int target, const unsigned int *table,
- unsigned int num_sel, unsigned int *sel)
+/**
+ * regulator_find_closest_bigger - helper to find offset in ramp delay table
+ *
+ * @target: targeted ramp_delay
+ * @table: table with supported ramp delays
+ * @num_sel: number of entries in the table
+ * @sel: Pointer to store table offset
+ *
+ * This is the internal helper used by regulator_set_ramp_delay_regmap to
+ * map ramp delay to register value. It should only be used directly if
+ * regulator_set_ramp_delay_regmap cannot handle a specific device setup
+ * (e.g. because the value is split over multiple registers).
+ */
+int regulator_find_closest_bigger(unsigned int target, const unsigned int *table,
+ unsigned int num_sel, unsigned int *sel)
{
unsigned int s, tmp, max, maxsel = 0;
bool found = false;
@@ -933,6 +946,7 @@ static int find_closest_bigger(unsigned int target, const unsigned int *table,
return 0;
}
+EXPORT_SYMBOL_GPL(regulator_find_closest_bigger);
/**
* regulator_set_ramp_delay_regmap - set_ramp_delay() helper
@@ -951,8 +965,8 @@ int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay)
if (WARN_ON(!rdev->desc->n_ramp_values || !rdev->desc->ramp_delay_table))
return -EINVAL;
- ret = find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
- rdev->desc->n_ramp_values, &sel);
+ ret = regulator_find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
+ rdev->desc->n_ramp_values, &sel);
if (ret) {
dev_warn(rdev_get_dev(rdev),
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index f9a7461e72b8..d6a3bb39d7dc 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -757,6 +757,8 @@ int regulator_set_current_limit_regmap(struct regulator_dev *rdev,
int min_uA, int max_uA);
int regulator_get_current_limit_regmap(struct regulator_dev *rdev);
void *regulator_get_init_drvdata(struct regulator_init_data *reg_init_data);
+int regulator_find_closest_bigger(unsigned int target, const unsigned int *table,
+ unsigned int num_sel, unsigned int *sel);
int regulator_set_ramp_delay_regmap(struct regulator_dev *rdev, int ramp_delay);
int regulator_sync_voltage_rdev(struct regulator_dev *rdev);
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 13/13] regulator: rk808: add rk806 support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-20 20:42 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel, shengfei Xu, Matti Vaittinen
Add rk806 support to the existing rk808 regulator
driver.
This has been implemented using shengfei Xu's rk806
specific driver from the vendor tree as reference.
Co-Developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 383 ++++++++++++++++++++++++++++
1 file changed, 383 insertions(+)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index fa9fc1aa1ae3..3d534d411104 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -3,9 +3,11 @@
* Regulator driver for Rockchip RK805/RK808/RK818
*
* Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
*
* Author: Chris Zhong <zyw@rock-chips.com>
* Author: Zhang Qing <zhangqing@rock-chips.com>
+ * Author: Xu Shengfei <xsf@rock-chips.com>
*
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
*
@@ -39,6 +41,13 @@
#define RK818_LDO3_ON_VSEL_MASK 0xf
#define RK818_BOOST_ON_VSEL_MASK 0xe0
+#define RK806_DCDC_SLP_REG_OFFSET 0x0A
+#define RK806_NLDO_SLP_REG_OFFSET 0x05
+#define RK806_PLDO_SLP_REG_OFFSET 0x06
+
+#define RK806_BUCK_SEL_CNT 0xff
+#define RK806_LDO_SEL_CNT 0xff
+
/* Ramp rate definitions for buck1 / buck2 only */
#define RK808_RAMP_RATE_OFFSET 3
#define RK808_RAMP_RATE_MASK (3 << RK808_RAMP_RATE_OFFSET)
@@ -117,6 +126,34 @@
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, 0, 0, _etime, &rk805_reg_ops)
+#define RK806_REGULATOR(_name, _supply_name, _id, _ops,\
+ _n_voltages, _vr, _er, _lr, ctrl_bit,\
+ _rr, _rm, _rt)\
+[_id] = {\
+ .name = _name,\
+ .supply_name = _supply_name,\
+ .of_match = of_match_ptr(_name),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .id = _id,\
+ .ops = &_ops,\
+ .type = REGULATOR_VOLTAGE,\
+ .n_voltages = _n_voltages,\
+ .linear_ranges = _lr,\
+ .n_linear_ranges = ARRAY_SIZE(_lr),\
+ .vsel_reg = _vr,\
+ .vsel_mask = 0xff,\
+ .enable_reg = _er,\
+ .enable_mask = ENABLE_MASK(ctrl_bit),\
+ .enable_val = ENABLE_MASK(ctrl_bit),\
+ .disable_val = DISABLE_VAL(ctrl_bit),\
+ .of_map_mode = rk8xx_regulator_of_map_mode,\
+ .ramp_reg = _rr,\
+ .ramp_mask = _rm,\
+ .ramp_delay_table = _rt, \
+ .n_ramp_values = ARRAY_SIZE(_rt), \
+ .owner = THIS_MODULE,\
+ }
+
#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, _etime) \
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
@@ -153,6 +190,17 @@
RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \
0, 0, &rk808_switch_ops)
+struct rk8xx_register_bit {
+ u8 reg;
+ u8 bit;
+};
+
+#define RK8XX_REG_BIT(_reg, _bit) \
+ { \
+ .reg = _reg, \
+ .bit = BIT(_bit), \
+ }
+
struct rk808_regulator_data {
struct gpio_desc *dvs_gpio[2];
};
@@ -216,6 +264,133 @@ static const unsigned int rk817_buck1_4_ramp_table[] = {
3000, 6300, 12500, 25000
};
+static int rk806_set_mode_dcdc(struct regulator_dev *rdev, unsigned int mode)
+{
+ int rid = rdev_get_id(rdev);
+ int ctr_bit, reg;
+
+ reg = RK806_POWER_FPWM_EN0 + rid / 8;
+ ctr_bit = rid % 8;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK << ctr_bit,
+ FPWM_MODE << ctr_bit);
+ case REGULATOR_MODE_NORMAL:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK << ctr_bit,
+ AUTO_PWM_MODE << ctr_bit);
+ default:
+ dev_err(rdev_get_dev(rdev), "mode unsupported: %u\n", mode);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static unsigned int rk806_get_mode_dcdc(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ int ctr_bit, reg;
+ unsigned int val;
+ int err;
+
+ reg = RK806_POWER_FPWM_EN0 + rid / 8;
+ ctr_bit = rid % 8;
+
+ err = regmap_read(rdev->regmap, reg, &val);
+ if (err)
+ return err;
+
+ if ((val >> ctr_bit) & FPWM_MODE)
+ return REGULATOR_MODE_FAST;
+ else
+ return REGULATOR_MODE_NORMAL;
+}
+
+static const struct rk8xx_register_bit rk806_dcdc_rate2[] = {
+ RK8XX_REG_BIT(0xEB, 0),
+ RK8XX_REG_BIT(0xEB, 1),
+ RK8XX_REG_BIT(0xEB, 2),
+ RK8XX_REG_BIT(0xEB, 3),
+ RK8XX_REG_BIT(0xEB, 4),
+ RK8XX_REG_BIT(0xEB, 5),
+ RK8XX_REG_BIT(0xEB, 6),
+ RK8XX_REG_BIT(0xEB, 7),
+ RK8XX_REG_BIT(0xEA, 0),
+ RK8XX_REG_BIT(0xEA, 1),
+};
+
+static const unsigned int rk806_ramp_delay_table_dcdc[] = {
+ 50000, 25000, 12500, 6250, 3125, 1560, 961, 390
+};
+
+static int rk806_set_ramp_delay_dcdc(struct regulator_dev *rdev, int ramp_delay)
+{
+ int rid = rdev_get_id(rdev);
+ int regval, ramp_value, ret;
+
+ ret = regulator_find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
+ rdev->desc->n_ramp_values, &ramp_value);
+ if (ret) {
+ dev_warn(rdev_get_dev(rdev),
+ "Can't set ramp-delay %u, setting %u\n", ramp_delay,
+ rdev->desc->ramp_delay_table[ramp_value]);
+ }
+
+ regval = ramp_value << (ffs(rdev->desc->ramp_mask) - 1);
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->ramp_reg,
+ rdev->desc->ramp_mask, regval);
+ if (ret)
+ return ret;
+
+ /*
+ * The above is effectively a copy of regulator_set_ramp_delay_regmap(),
+ * but that only stores the lower 2 bits for rk806 DCDC ramp. The MSB must
+ * be stored in a separate register, so this open codes the implementation
+ * to have access to the ramp_value.
+ */
+
+ regval = (ramp_value >> 2) & 0x1 ? rk806_dcdc_rate2[rid].bit : 0;
+ return regmap_update_bits(rdev->regmap, rk806_dcdc_rate2[rid].reg,
+ rk806_dcdc_rate2[rid].bit,
+ regval);
+}
+
+static const unsigned int rk806_ramp_delay_table_ldo[] = {
+ 100000, 50000, 25000, 12500, 6280, 3120, 1900, 780
+};
+
+static int rk806_set_suspend_voltage_range(struct regulator_dev *rdev, int reg_offset, int uv)
+{
+ int sel = regulator_map_voltage_linear_range(rdev, uv, uv);
+ unsigned int reg;
+
+ if (sel < 0)
+ return -EINVAL;
+
+ reg = rdev->desc->vsel_reg + reg_offset;
+
+ return regmap_update_bits(rdev->regmap, reg, rdev->desc->vsel_mask, sel);
+}
+
+static int rk806_set_suspend_voltage_range_dcdc(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_DCDC_SLP_REG_OFFSET, uv);
+}
+
+static int rk806_set_suspend_voltage_range_nldo(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_NLDO_SLP_REG_OFFSET, uv);
+}
+
+static int rk806_set_suspend_voltage_range_pldo(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_PLDO_SLP_REG_OFFSET, uv);
+}
+
static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
{
struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
@@ -393,6 +568,45 @@ static int rk805_set_suspend_disable(struct regulator_dev *rdev)
0);
}
+static const struct rk8xx_register_bit rk806_suspend_bits[] = {
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 0),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 5),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 6),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 7),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 6),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 7),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 0),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 5),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 0),
+};
+
+static int rk806_set_suspend_enable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg,
+ rk806_suspend_bits[rid].bit,
+ rk806_suspend_bits[rid].bit);
+}
+
+static int rk806_set_suspend_disable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg,
+ rk806_suspend_bits[rid].bit, 0);
+}
+
static int rk808_set_suspend_enable(struct regulator_dev *rdev)
{
unsigned int reg;
@@ -561,6 +775,64 @@ static const struct regulator_ops rk805_switch_ops = {
.set_suspend_disable = rk805_set_suspend_disable,
};
+static const struct regulator_ops rk806_ops_dcdc = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_mode = rk806_set_mode_dcdc,
+ .get_mode = rk806_get_mode_dcdc,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+
+ .set_suspend_mode = rk806_set_mode_dcdc,
+ .set_ramp_delay = rk806_set_ramp_delay_dcdc,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_dcdc,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
+static const struct regulator_ops rk806_ops_nldo = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_nldo,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
+static const struct regulator_ops rk806_ops_pldo = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_pldo,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
static const struct regulator_ops rk808_buck1_2_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -743,6 +1015,112 @@ static const struct regulator_desc rk805_reg[] = {
BIT(2), 400),
};
+static const struct linear_range rk806_buck_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 160, 6250), /* 500mV ~ 1500mV */
+ REGULATOR_LINEAR_RANGE(1500000, 161, 237, 25000), /* 1500mV ~ 3400mV */
+ REGULATOR_LINEAR_RANGE(3400000, 238, 255, 0),
+};
+
+static const struct linear_range rk806_ldo_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 232, 12500), /* 500mV ~ 3400mV */
+ REGULATOR_LINEAR_RANGE(3400000, 233, 255, 0), /* 500mV ~ 3400mV */
+};
+
+static const struct regulator_desc rk806_reg[] = {
+ RK806_REGULATOR("dcdc-reg1", "vcc1", RK806_ID_DCDC1, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK1_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK1_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg2", "vcc2", RK806_ID_DCDC2, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK2_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK2_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg3", "vcc3", RK806_ID_DCDC3, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK3_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 2,
+ RK806_BUCK3_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg4", "vcc4", RK806_ID_DCDC4, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK4_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 3,
+ RK806_BUCK4_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("dcdc-reg5", "vcc5", RK806_ID_DCDC5, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK5_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK5_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg6", "vcc6", RK806_ID_DCDC6, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK6_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK6_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg7", "vcc7", RK806_ID_DCDC7, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK7_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 2,
+ RK806_BUCK7_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg8", "vcc8", RK806_ID_DCDC8, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK8_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 3,
+ RK806_BUCK8_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("dcdc-reg9", "vcc9", RK806_ID_DCDC9, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK9_ON_VSEL,
+ RK806_POWER_EN2, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK9_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg10", "vcc10", RK806_ID_DCDC10, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK10_ON_VSEL,
+ RK806_POWER_EN2, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK10_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("nldo-reg1", "vcc13", RK806_ID_NLDO1, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO1_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg2", "vcc13", RK806_ID_NLDO2, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO2_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg3", "vcc13", RK806_ID_NLDO3, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO3_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg4", "vcc14", RK806_ID_NLDO4, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO4_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 3,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("nldo-reg5", "vcc14", RK806_ID_NLDO5, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO5_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg1", "vcc11", RK806_ID_PLDO1, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO1_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg2", "vcc11", RK806_ID_PLDO2, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO2_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg3", "vcc11", RK806_ID_PLDO3, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO3_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 3,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg4", "vcc12", RK806_ID_PLDO4, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO4_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg5", "vcc12", RK806_ID_PLDO5, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO5_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg6", "vcca", RK806_ID_PLDO6, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO6_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+};
+
+
static const struct regulator_desc rk808_reg[] = {
{
.name = "DCDC_REG1",
@@ -1312,6 +1690,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
regulators = rk805_reg;
nregulators = RK805_NUM_REGULATORS;
break;
+ case RK806_ID:
+ regulators = rk806_reg;
+ nregulators = ARRAY_SIZE(rk806_reg);
+ break;
case RK808_ID:
regulators = rk808_reg;
nregulators = RK808_NUM_REGULATORS;
@@ -1365,5 +1747,6 @@ MODULE_AUTHOR("Tony xie <tony.xie@rock-chips.com>");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:rk808-regulator");
--
2.35.1
^ permalink raw reply related [flat|nested] 44+ messages in thread
* [PATCHv4 13/13] regulator: rk808: add rk806 support
@ 2022-10-20 20:42 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-10-20 20:42 UTC (permalink / raw)
To: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones
Cc: Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, Sebastian Reichel,
kernel, shengfei Xu, Matti Vaittinen
Add rk806 support to the existing rk808 regulator
driver.
This has been implemented using shengfei Xu's rk806
specific driver from the vendor tree as reference.
Co-Developed-by: shengfei Xu <xsf@rock-chips.com>
Signed-off-by: shengfei Xu <xsf@rock-chips.com>
Reviewed-by: Matti Vaittinen <mazziesaccount@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/regulator/rk808-regulator.c | 383 ++++++++++++++++++++++++++++
1 file changed, 383 insertions(+)
diff --git a/drivers/regulator/rk808-regulator.c b/drivers/regulator/rk808-regulator.c
index fa9fc1aa1ae3..3d534d411104 100644
--- a/drivers/regulator/rk808-regulator.c
+++ b/drivers/regulator/rk808-regulator.c
@@ -3,9 +3,11 @@
* Regulator driver for Rockchip RK805/RK808/RK818
*
* Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
*
* Author: Chris Zhong <zyw@rock-chips.com>
* Author: Zhang Qing <zhangqing@rock-chips.com>
+ * Author: Xu Shengfei <xsf@rock-chips.com>
*
* Copyright (C) 2016 PHYTEC Messtechnik GmbH
*
@@ -39,6 +41,13 @@
#define RK818_LDO3_ON_VSEL_MASK 0xf
#define RK818_BOOST_ON_VSEL_MASK 0xe0
+#define RK806_DCDC_SLP_REG_OFFSET 0x0A
+#define RK806_NLDO_SLP_REG_OFFSET 0x05
+#define RK806_PLDO_SLP_REG_OFFSET 0x06
+
+#define RK806_BUCK_SEL_CNT 0xff
+#define RK806_LDO_SEL_CNT 0xff
+
/* Ramp rate definitions for buck1 / buck2 only */
#define RK808_RAMP_RATE_OFFSET 3
#define RK808_RAMP_RATE_MASK (3 << RK808_RAMP_RATE_OFFSET)
@@ -117,6 +126,34 @@
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, 0, 0, _etime, &rk805_reg_ops)
+#define RK806_REGULATOR(_name, _supply_name, _id, _ops,\
+ _n_voltages, _vr, _er, _lr, ctrl_bit,\
+ _rr, _rm, _rt)\
+[_id] = {\
+ .name = _name,\
+ .supply_name = _supply_name,\
+ .of_match = of_match_ptr(_name),\
+ .regulators_node = of_match_ptr("regulators"),\
+ .id = _id,\
+ .ops = &_ops,\
+ .type = REGULATOR_VOLTAGE,\
+ .n_voltages = _n_voltages,\
+ .linear_ranges = _lr,\
+ .n_linear_ranges = ARRAY_SIZE(_lr),\
+ .vsel_reg = _vr,\
+ .vsel_mask = 0xff,\
+ .enable_reg = _er,\
+ .enable_mask = ENABLE_MASK(ctrl_bit),\
+ .enable_val = ENABLE_MASK(ctrl_bit),\
+ .disable_val = DISABLE_VAL(ctrl_bit),\
+ .of_map_mode = rk8xx_regulator_of_map_mode,\
+ .ramp_reg = _rr,\
+ .ramp_mask = _rm,\
+ .ramp_delay_table = _rt, \
+ .n_ramp_values = ARRAY_SIZE(_rt), \
+ .owner = THIS_MODULE,\
+ }
+
#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg, \
_vmask, _ereg, _emask, _etime) \
RK8XX_DESC_COM(_id, _match, _supply, _min, _max, _step, _vreg, \
@@ -153,6 +190,17 @@
RKXX_DESC_SWITCH_COM(_id, _match, _supply, _ereg, _emask, \
0, 0, &rk808_switch_ops)
+struct rk8xx_register_bit {
+ u8 reg;
+ u8 bit;
+};
+
+#define RK8XX_REG_BIT(_reg, _bit) \
+ { \
+ .reg = _reg, \
+ .bit = BIT(_bit), \
+ }
+
struct rk808_regulator_data {
struct gpio_desc *dvs_gpio[2];
};
@@ -216,6 +264,133 @@ static const unsigned int rk817_buck1_4_ramp_table[] = {
3000, 6300, 12500, 25000
};
+static int rk806_set_mode_dcdc(struct regulator_dev *rdev, unsigned int mode)
+{
+ int rid = rdev_get_id(rdev);
+ int ctr_bit, reg;
+
+ reg = RK806_POWER_FPWM_EN0 + rid / 8;
+ ctr_bit = rid % 8;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK << ctr_bit,
+ FPWM_MODE << ctr_bit);
+ case REGULATOR_MODE_NORMAL:
+ return regmap_update_bits(rdev->regmap, reg,
+ PWM_MODE_MSK << ctr_bit,
+ AUTO_PWM_MODE << ctr_bit);
+ default:
+ dev_err(rdev_get_dev(rdev), "mode unsupported: %u\n", mode);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static unsigned int rk806_get_mode_dcdc(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ int ctr_bit, reg;
+ unsigned int val;
+ int err;
+
+ reg = RK806_POWER_FPWM_EN0 + rid / 8;
+ ctr_bit = rid % 8;
+
+ err = regmap_read(rdev->regmap, reg, &val);
+ if (err)
+ return err;
+
+ if ((val >> ctr_bit) & FPWM_MODE)
+ return REGULATOR_MODE_FAST;
+ else
+ return REGULATOR_MODE_NORMAL;
+}
+
+static const struct rk8xx_register_bit rk806_dcdc_rate2[] = {
+ RK8XX_REG_BIT(0xEB, 0),
+ RK8XX_REG_BIT(0xEB, 1),
+ RK8XX_REG_BIT(0xEB, 2),
+ RK8XX_REG_BIT(0xEB, 3),
+ RK8XX_REG_BIT(0xEB, 4),
+ RK8XX_REG_BIT(0xEB, 5),
+ RK8XX_REG_BIT(0xEB, 6),
+ RK8XX_REG_BIT(0xEB, 7),
+ RK8XX_REG_BIT(0xEA, 0),
+ RK8XX_REG_BIT(0xEA, 1),
+};
+
+static const unsigned int rk806_ramp_delay_table_dcdc[] = {
+ 50000, 25000, 12500, 6250, 3125, 1560, 961, 390
+};
+
+static int rk806_set_ramp_delay_dcdc(struct regulator_dev *rdev, int ramp_delay)
+{
+ int rid = rdev_get_id(rdev);
+ int regval, ramp_value, ret;
+
+ ret = regulator_find_closest_bigger(ramp_delay, rdev->desc->ramp_delay_table,
+ rdev->desc->n_ramp_values, &ramp_value);
+ if (ret) {
+ dev_warn(rdev_get_dev(rdev),
+ "Can't set ramp-delay %u, setting %u\n", ramp_delay,
+ rdev->desc->ramp_delay_table[ramp_value]);
+ }
+
+ regval = ramp_value << (ffs(rdev->desc->ramp_mask) - 1);
+
+ ret = regmap_update_bits(rdev->regmap, rdev->desc->ramp_reg,
+ rdev->desc->ramp_mask, regval);
+ if (ret)
+ return ret;
+
+ /*
+ * The above is effectively a copy of regulator_set_ramp_delay_regmap(),
+ * but that only stores the lower 2 bits for rk806 DCDC ramp. The MSB must
+ * be stored in a separate register, so this open codes the implementation
+ * to have access to the ramp_value.
+ */
+
+ regval = (ramp_value >> 2) & 0x1 ? rk806_dcdc_rate2[rid].bit : 0;
+ return regmap_update_bits(rdev->regmap, rk806_dcdc_rate2[rid].reg,
+ rk806_dcdc_rate2[rid].bit,
+ regval);
+}
+
+static const unsigned int rk806_ramp_delay_table_ldo[] = {
+ 100000, 50000, 25000, 12500, 6280, 3120, 1900, 780
+};
+
+static int rk806_set_suspend_voltage_range(struct regulator_dev *rdev, int reg_offset, int uv)
+{
+ int sel = regulator_map_voltage_linear_range(rdev, uv, uv);
+ unsigned int reg;
+
+ if (sel < 0)
+ return -EINVAL;
+
+ reg = rdev->desc->vsel_reg + reg_offset;
+
+ return regmap_update_bits(rdev->regmap, reg, rdev->desc->vsel_mask, sel);
+}
+
+static int rk806_set_suspend_voltage_range_dcdc(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_DCDC_SLP_REG_OFFSET, uv);
+}
+
+static int rk806_set_suspend_voltage_range_nldo(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_NLDO_SLP_REG_OFFSET, uv);
+}
+
+static int rk806_set_suspend_voltage_range_pldo(struct regulator_dev *rdev, int uv)
+{
+ return rk806_set_suspend_voltage_range(rdev, RK806_PLDO_SLP_REG_OFFSET, uv);
+}
+
static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
{
struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
@@ -393,6 +568,45 @@ static int rk805_set_suspend_disable(struct regulator_dev *rdev)
0);
}
+static const struct rk8xx_register_bit rk806_suspend_bits[] = {
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 0),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 5),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 6),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN0, 7),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 6),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 7),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 0),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN1, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 1),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 2),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 3),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 4),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 5),
+ RK8XX_REG_BIT(RK806_POWER_SLP_EN2, 0),
+};
+
+static int rk806_set_suspend_enable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg,
+ rk806_suspend_bits[rid].bit,
+ rk806_suspend_bits[rid].bit);
+}
+
+static int rk806_set_suspend_disable(struct regulator_dev *rdev)
+{
+ int rid = rdev_get_id(rdev);
+ return regmap_update_bits(rdev->regmap, rk806_suspend_bits[rid].reg,
+ rk806_suspend_bits[rid].bit, 0);
+}
+
static int rk808_set_suspend_enable(struct regulator_dev *rdev)
{
unsigned int reg;
@@ -561,6 +775,64 @@ static const struct regulator_ops rk805_switch_ops = {
.set_suspend_disable = rk805_set_suspend_disable,
};
+static const struct regulator_ops rk806_ops_dcdc = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_mode = rk806_set_mode_dcdc,
+ .get_mode = rk806_get_mode_dcdc,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = rk8xx_is_enabled_wmsk_regmap,
+
+ .set_suspend_mode = rk806_set_mode_dcdc,
+ .set_ramp_delay = rk806_set_ramp_delay_dcdc,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_dcdc,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
+static const struct regulator_ops rk806_ops_nldo = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_nldo,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
+static const struct regulator_ops rk806_ops_pldo = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+
+ .set_ramp_delay = regulator_set_ramp_delay_regmap,
+
+ .set_suspend_voltage = rk806_set_suspend_voltage_range_pldo,
+ .set_suspend_enable = rk806_set_suspend_enable,
+ .set_suspend_disable = rk806_set_suspend_disable,
+};
+
static const struct regulator_ops rk808_buck1_2_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -743,6 +1015,112 @@ static const struct regulator_desc rk805_reg[] = {
BIT(2), 400),
};
+static const struct linear_range rk806_buck_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 160, 6250), /* 500mV ~ 1500mV */
+ REGULATOR_LINEAR_RANGE(1500000, 161, 237, 25000), /* 1500mV ~ 3400mV */
+ REGULATOR_LINEAR_RANGE(3400000, 238, 255, 0),
+};
+
+static const struct linear_range rk806_ldo_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0, 232, 12500), /* 500mV ~ 3400mV */
+ REGULATOR_LINEAR_RANGE(3400000, 233, 255, 0), /* 500mV ~ 3400mV */
+};
+
+static const struct regulator_desc rk806_reg[] = {
+ RK806_REGULATOR("dcdc-reg1", "vcc1", RK806_ID_DCDC1, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK1_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK1_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg2", "vcc2", RK806_ID_DCDC2, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK2_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK2_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg3", "vcc3", RK806_ID_DCDC3, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK3_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 2,
+ RK806_BUCK3_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg4", "vcc4", RK806_ID_DCDC4, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK4_ON_VSEL,
+ RK806_POWER_EN0, rk806_buck_voltage_ranges, 3,
+ RK806_BUCK4_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("dcdc-reg5", "vcc5", RK806_ID_DCDC5, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK5_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK5_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg6", "vcc6", RK806_ID_DCDC6, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK6_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK6_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg7", "vcc7", RK806_ID_DCDC7, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK7_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 2,
+ RK806_BUCK7_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg8", "vcc8", RK806_ID_DCDC8, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK8_ON_VSEL,
+ RK806_POWER_EN1, rk806_buck_voltage_ranges, 3,
+ RK806_BUCK8_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("dcdc-reg9", "vcc9", RK806_ID_DCDC9, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK9_ON_VSEL,
+ RK806_POWER_EN2, rk806_buck_voltage_ranges, 0,
+ RK806_BUCK9_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+ RK806_REGULATOR("dcdc-reg10", "vcc10", RK806_ID_DCDC10, rk806_ops_dcdc,
+ RK806_BUCK_SEL_CNT, RK806_BUCK10_ON_VSEL,
+ RK806_POWER_EN2, rk806_buck_voltage_ranges, 1,
+ RK806_BUCK10_CONFIG, 0xc0, rk806_ramp_delay_table_dcdc),
+
+ RK806_REGULATOR("nldo-reg1", "vcc13", RK806_ID_NLDO1, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO1_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg2", "vcc13", RK806_ID_NLDO2, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO2_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg3", "vcc13", RK806_ID_NLDO3, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO3_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("nldo-reg4", "vcc14", RK806_ID_NLDO4, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO4_ON_VSEL,
+ RK806_POWER_EN3, rk806_ldo_voltage_ranges, 3,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("nldo-reg5", "vcc14", RK806_ID_NLDO5, rk806_ops_nldo,
+ RK806_LDO_SEL_CNT, RK806_NLDO5_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg1", "vcc11", RK806_ID_PLDO1, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO1_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg2", "vcc11", RK806_ID_PLDO2, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO2_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 2,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg3", "vcc11", RK806_ID_PLDO3, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO3_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 3,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg4", "vcc12", RK806_ID_PLDO4, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO4_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+ RK806_REGULATOR("pldo-reg5", "vcc12", RK806_ID_PLDO5, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO5_ON_VSEL,
+ RK806_POWER_EN5, rk806_ldo_voltage_ranges, 1,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+
+ RK806_REGULATOR("pldo-reg6", "vcca", RK806_ID_PLDO6, rk806_ops_pldo,
+ RK806_LDO_SEL_CNT, RK806_PLDO6_ON_VSEL,
+ RK806_POWER_EN4, rk806_ldo_voltage_ranges, 0,
+ 0xEA, 0x38, rk806_ramp_delay_table_ldo),
+};
+
+
static const struct regulator_desc rk808_reg[] = {
{
.name = "DCDC_REG1",
@@ -1312,6 +1690,10 @@ static int rk808_regulator_probe(struct platform_device *pdev)
regulators = rk805_reg;
nregulators = RK805_NUM_REGULATORS;
break;
+ case RK806_ID:
+ regulators = rk806_reg;
+ nregulators = ARRAY_SIZE(rk806_reg);
+ break;
case RK808_ID:
regulators = rk808_reg;
nregulators = RK808_NUM_REGULATORS;
@@ -1365,5 +1747,6 @@ MODULE_AUTHOR("Tony xie <tony.xie@rock-chips.com>");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
+MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:rk808-regulator");
--
2.35.1
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply related [flat|nested] 44+ messages in thread
* Re: [PATCHv4 08/13] dt-bindings: mfd: add rk806 binding
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-21 22:19 ` Rob Herring
-1 siblings, 0 replies; 44+ messages in thread
From: Rob Herring @ 2022-10-21 22:19 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, Oct 20, 2022 at 10:42:46PM +0200, Sebastian Reichel wrote:
> Add DT binding document for Rockchip's RK806 PMIC.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> .../bindings/mfd/rockchip,rk806.yaml | 405 ++++++++++++++++++
> 1 file changed, 405 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
> new file mode 100644
> index 000000000000..4e907dd1f7a4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
> @@ -0,0 +1,405 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: RK806 Power Management Integrated Circuit
> +
> +maintainers:
> + - Sebastian Reichel <sebastian.reichel@collabora.com>
> +
> +description: |
Don't need '|' if no formatting to preserve.
> + Rockchip RK806 series PMIC. This device consists of an spi or
> + i2c controlled MFD that includes multiple switchable regulators.
> +
> +properties:
> + compatible:
> + enum:
> + - rockchip,rk806
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + vcc1-supply:
> + description:
> + The input supply for dcdc-reg1.
> +
> + vcc2-supply:
> + description:
> + The input supply for dcdc-reg2.
> +
> + vcc3-supply:
> + description:
> + The input supply for dcdc-reg3.
> +
> + vcc4-supply:
> + description:
> + The input supply for dcdc-reg4.
> +
> + vcc5-supply:
> + description:
> + The input supply for dcdc-reg5.
> +
> + vcc6-supply:
> + description:
> + The input supply for dcdc-reg6.
> +
> + vcc7-supply:
> + description:
> + The input supply for dcdc-reg7.
> +
> + vcc8-supply:
> + description:
> + The input supply for dcdc-reg8.
> +
> + vcc9-supply:
> + description:
> + The input supply for dcdc-reg9.
> +
> + vcc10-supply:
> + description:
> + The input supply for dcdc-reg10.
> +
> + vcc11-supply:
> + description:
> + The input supply for pldo-reg1, pldo-reg2 and pldo-reg3.
> +
> + vcc12-supply:
> + description:
> + The input supply for pldo-reg4 and pldo-reg5.
> +
> + vcc13-supply:
> + description:
> + The input supply for nldo-reg1, nldo-reg2 and nldo-reg3.
> +
> + vcc14-supply:
> + description:
> + The input supply for nldo-reg4 and nldo-reg5.
> +
> + vcca-supply:
> + description:
> + The input supply for pldo-reg6.
> +
> + regulators:
> + type: object
> + patternProperties:
> + "^(dcdc-reg([1-9]|10)|pldo-reg[1-6]|nldo-reg[1-5])$":
> + type: object
> + $ref: /schemas/regulator/regulator.yaml#
> + unevaluatedProperties: false
> + additionalProperties: false
In the indented cases, this is a bit easier to read if placed before
patternProperties.
> +
> +patternProperties:
> + '-pins$':
> + type: object
additionalProperties: false
(or unevaluatedProperties if other properties besides function and pins
apply.)
> + $ref: /schemas/pinctrl/pinmux-node.yaml
> +
> + properties:
> + function:
> + enum: [pin_fun0, pin_fun1, pin_fun2, pin_fun3, pin_fun4, pin_fun5]
> +
> + pins:
> + $ref: "/schemas/types.yaml#/definitions/string"
Can drop quotes.
> + enum: [gpio_pwrctrl1, gpio_pwrctrl2, gpio_pwrctrl3]
> +
> +allOf:
> + - $ref: /schemas/spi/spi-peripheral-props.yaml
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/pinctrl/rockchip.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/gpio/gpio.h>
> + spi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmic@0 {
> + compatible = "rockchip,rk806";
> + reg = <0x0>;
> +
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc5v0_sys>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + regulators {
> + vdd_gpu_s0: dcdc-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_npu_s0: dcdc-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_npu_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_log_s0: dcdc-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_log_s0";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_vdenc_s0: dcdc-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu_mem_s0: dcdc-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_npu_mem_s0: dcdc-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_npu_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_2v0_pldo_s3: dcdc-reg7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_2v0_pldo_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2000000>;
> + };
> + };
> +
> + vdd_vdenc_mem_s0: dcdc-reg8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd2_ddr_s3: dcdc-reg9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd2_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v1_nldo_s3: dcdc-reg10 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_1v1_nldo_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1100000>;
> + };
> + };
> +
> + avcc_1v8_s0: pldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "avcc_1v8_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd1_1v8_ddr_s3: pldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd1_1v8_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_1v8_s3: pldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_1v8_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_3v3_s0: pldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_3v3_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd_s0: pldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vccio_sd_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + master_pldo6_s3: pldo-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "master_pldo6_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_0v75_s3: nldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_0v75_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd2l_0v9_ddr_s3: nldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdd2l_0v9_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + master_nldo3: nldo-reg3 {
> + regulator-name = "master_nldo3";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + avdd_0v75_s0: nldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "avdd_0v75_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v85_s0: nldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_0v85_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> + };
> --
> 2.35.1
>
>
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 08/13] dt-bindings: mfd: add rk806 binding
@ 2022-10-21 22:19 ` Rob Herring
0 siblings, 0 replies; 44+ messages in thread
From: Rob Herring @ 2022-10-21 22:19 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, Oct 20, 2022 at 10:42:46PM +0200, Sebastian Reichel wrote:
> Add DT binding document for Rockchip's RK806 PMIC.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> .../bindings/mfd/rockchip,rk806.yaml | 405 ++++++++++++++++++
> 1 file changed, 405 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
> new file mode 100644
> index 000000000000..4e907dd1f7a4
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rockchip,rk806.yaml
> @@ -0,0 +1,405 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/rockchip,rk806.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: RK806 Power Management Integrated Circuit
> +
> +maintainers:
> + - Sebastian Reichel <sebastian.reichel@collabora.com>
> +
> +description: |
Don't need '|' if no formatting to preserve.
> + Rockchip RK806 series PMIC. This device consists of an spi or
> + i2c controlled MFD that includes multiple switchable regulators.
> +
> +properties:
> + compatible:
> + enum:
> + - rockchip,rk806
> +
> + reg:
> + maxItems: 1
> +
> + interrupts:
> + maxItems: 1
> +
> + gpio-controller: true
> +
> + '#gpio-cells':
> + const: 2
> +
> + vcc1-supply:
> + description:
> + The input supply for dcdc-reg1.
> +
> + vcc2-supply:
> + description:
> + The input supply for dcdc-reg2.
> +
> + vcc3-supply:
> + description:
> + The input supply for dcdc-reg3.
> +
> + vcc4-supply:
> + description:
> + The input supply for dcdc-reg4.
> +
> + vcc5-supply:
> + description:
> + The input supply for dcdc-reg5.
> +
> + vcc6-supply:
> + description:
> + The input supply for dcdc-reg6.
> +
> + vcc7-supply:
> + description:
> + The input supply for dcdc-reg7.
> +
> + vcc8-supply:
> + description:
> + The input supply for dcdc-reg8.
> +
> + vcc9-supply:
> + description:
> + The input supply for dcdc-reg9.
> +
> + vcc10-supply:
> + description:
> + The input supply for dcdc-reg10.
> +
> + vcc11-supply:
> + description:
> + The input supply for pldo-reg1, pldo-reg2 and pldo-reg3.
> +
> + vcc12-supply:
> + description:
> + The input supply for pldo-reg4 and pldo-reg5.
> +
> + vcc13-supply:
> + description:
> + The input supply for nldo-reg1, nldo-reg2 and nldo-reg3.
> +
> + vcc14-supply:
> + description:
> + The input supply for nldo-reg4 and nldo-reg5.
> +
> + vcca-supply:
> + description:
> + The input supply for pldo-reg6.
> +
> + regulators:
> + type: object
> + patternProperties:
> + "^(dcdc-reg([1-9]|10)|pldo-reg[1-6]|nldo-reg[1-5])$":
> + type: object
> + $ref: /schemas/regulator/regulator.yaml#
> + unevaluatedProperties: false
> + additionalProperties: false
In the indented cases, this is a bit easier to read if placed before
patternProperties.
> +
> +patternProperties:
> + '-pins$':
> + type: object
additionalProperties: false
(or unevaluatedProperties if other properties besides function and pins
apply.)
> + $ref: /schemas/pinctrl/pinmux-node.yaml
> +
> + properties:
> + function:
> + enum: [pin_fun0, pin_fun1, pin_fun2, pin_fun3, pin_fun4, pin_fun5]
> +
> + pins:
> + $ref: "/schemas/types.yaml#/definitions/string"
Can drop quotes.
> + enum: [gpio_pwrctrl1, gpio_pwrctrl2, gpio_pwrctrl3]
> +
> +allOf:
> + - $ref: /schemas/spi/spi-peripheral-props.yaml
> +
> +required:
> + - compatible
> + - reg
> + - interrupts
> +
> +unevaluatedProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/pinctrl/rockchip.h>
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/gpio/gpio.h>
> + spi {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + pmic@0 {
> + compatible = "rockchip,rk806";
> + reg = <0x0>;
> +
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> +
> + vcc1-supply = <&vcc5v0_sys>;
> + vcc2-supply = <&vcc5v0_sys>;
> + vcc3-supply = <&vcc5v0_sys>;
> + vcc4-supply = <&vcc5v0_sys>;
> + vcc5-supply = <&vcc5v0_sys>;
> + vcc6-supply = <&vcc5v0_sys>;
> + vcc7-supply = <&vcc5v0_sys>;
> + vcc8-supply = <&vcc5v0_sys>;
> + vcc9-supply = <&vcc5v0_sys>;
> + vcc10-supply = <&vcc5v0_sys>;
> + vcc11-supply = <&vcc_2v0_pldo_s3>;
> + vcc12-supply = <&vcc5v0_sys>;
> + vcc13-supply = <&vcc5v0_sys>;
> + vcc14-supply = <&vcc_1v1_nldo_s3>;
> + vcca-supply = <&vcc5v0_sys>;
> +
> + regulators {
> + vdd_gpu_s0: dcdc-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_npu_s0: dcdc-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_npu_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_log_s0: dcdc-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_log_s0";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd_vdenc_s0: dcdc-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_gpu_mem_s0: dcdc-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_gpu_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_npu_mem_s0: dcdc-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_npu_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vcc_2v0_pldo_s3: dcdc-reg7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_2v0_pldo_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <2000000>;
> + };
> + };
> +
> + vdd_vdenc_mem_s0: dcdc-reg8 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <675000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_vdenc_mem_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd2_ddr_s3: dcdc-reg9 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-name = "vdd2_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + };
> + };
> +
> + vcc_1v1_nldo_s3: dcdc-reg10 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_1v1_nldo_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1100000>;
> + };
> + };
> +
> + avcc_1v8_s0: pldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "avcc_1v8_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd1_1v8_ddr_s3: pldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd1_1v8_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_1v8_s3: pldo-reg3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_1v8_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vcc_3v3_s0: pldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vcc_3v3_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vccio_sd_s0: pldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vccio_sd_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + master_pldo6_s3: pldo-reg6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "master_pldo6_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <1800000>;
> + };
> + };
> +
> + vdd_0v75_s3: nldo-reg1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-ramp-delay = <12500>;
> + regulator-name = "vdd_0v75_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <750000>;
> + };
> + };
> +
> + vdd2l_0v9_ddr_s3: nldo-reg2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-name = "vdd2l_0v9_ddr_s3";
> + regulator-state-mem {
> + regulator-on-in-suspend;
> + regulator-suspend-microvolt = <900000>;
> + };
> + };
> +
> + master_nldo3: nldo-reg3 {
> + regulator-name = "master_nldo3";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + avdd_0v75_s0: nldo-reg4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <750000>;
> + regulator-max-microvolt = <750000>;
> + regulator-name = "avdd_0v75_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_0v85_s0: nldo-reg5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <850000>;
> + regulator-name = "vdd_0v85_s0";
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> + };
> + };
> + };
> --
> 2.35.1
>
>
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 07/13] mfd: rk808: split into core and i2c
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-31 13:56 ` Lee Jones
-1 siblings, 0 replies; 44+ messages in thread
From: Lee Jones @ 2022-10-31 13:56 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, 20 Oct 2022, Sebastian Reichel wrote:
> Split rk808 into a core and an i2c part in preperation for
> SPI support.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> drivers/clk/Kconfig | 2 +-
> drivers/input/misc/Kconfig | 2 +-
> drivers/mfd/Kconfig | 7 +-
> drivers/mfd/Makefile | 3 +-
> drivers/mfd/{rk808.c => rk8xx-core.c} | 210 ++++----------------------
> drivers/mfd/rk8xx-i2c.c | 209 +++++++++++++++++++++++++
> drivers/pinctrl/Kconfig | 2 +-
> drivers/power/supply/Kconfig | 2 +-
> drivers/regulator/Kconfig | 2 +-
> drivers/rtc/Kconfig | 2 +-
> include/linux/mfd/rk808.h | 6 +
> sound/soc/codecs/Kconfig | 2 +-
> 12 files changed, 263 insertions(+), 186 deletions(-)
> rename drivers/mfd/{rk808.c => rk8xx-core.c} (75%)
> create mode 100644 drivers/mfd/rk8xx-i2c.c
>
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index d79905f3e174..8448d616b9aa 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -83,7 +83,7 @@ config COMMON_CLK_MAX9485
>
> config COMMON_CLK_RK808
> tristate "Clock driver for RK805/RK808/RK809/RK817/RK818"
> - depends on MFD_RK808
> + depends on MFD_RK8XX
> help
> This driver supports RK805, RK809 and RK817, RK808 and RK818 crystal oscillator clock.
> These multi-function devices have two fixed-rate oscillators, clocked at 32KHz each.
> diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
> index 9f088900f863..1899afeaec47 100644
> --- a/drivers/input/misc/Kconfig
> +++ b/drivers/input/misc/Kconfig
> @@ -588,7 +588,7 @@ config INPUT_PWM_VIBRA
>
> config INPUT_RK805_PWRKEY
> tristate "Rockchip RK805 PMIC power key support"
> - depends on MFD_RK808
> + depends on MFD_RK8XX
> help
> Select this option to enable power key driver for RK805.
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 8b93856de432..8e3de443cc3d 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1201,12 +1201,17 @@ config MFD_RC5T583
> Additional drivers must be enabled in order to use the
> different functionality of the device.
>
> -config MFD_RK808
> +config MFD_RK8XX
> + bool
> + select MFD_CORE
> +
> +config MFD_RK8XX_I2C
> tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
> depends on I2C && OF
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> + select MFD_RK8XX
> help
> If you say yes here you get support for the RK805, RK808, RK809,
> RK817 and RK818 Power Management chips.
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 7ed3ef4a698c..edf84e870f98 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -223,7 +223,8 @@ obj-$(CONFIG_MFD_PALMAS) += palmas.o
> obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
> obj-$(CONFIG_MFD_NTXEC) += ntxec.o
> obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
> -obj-$(CONFIG_MFD_RK808) += rk808.o
> +obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
> +obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
> obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
> obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
> obj-$(CONFIG_MFD_SYSCON) += syscon.o
> diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk8xx-core.c
> similarity index 75%
> rename from drivers/mfd/rk808.c
> rename to drivers/mfd/rk8xx-core.c
> index b154ca96d812..098506972710 100644
> --- a/drivers/mfd/rk808.c
> +++ b/drivers/mfd/rk8xx-core.c
> @@ -3,16 +3,9 @@
> * MFD core driver for Rockchip RK808/RK818
> *
> * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
> - *
> - * Author: Chris Zhong <zyw@rock-chips.com>
> - * Author: Zhang Qing <zhangqing@rock-chips.com>
> - *
> * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> - *
> - * Author: Wadim Egorov <w.egorov@phytec.de>
> */
The patch and the premise behind it look reasonable.
What's the reason for taking out the Author tags?
--
Lee Jones [李琼斯]
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 07/13] mfd: rk808: split into core and i2c
@ 2022-10-31 13:56 ` Lee Jones
0 siblings, 0 replies; 44+ messages in thread
From: Lee Jones @ 2022-10-31 13:56 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, 20 Oct 2022, Sebastian Reichel wrote:
> Split rk808 into a core and an i2c part in preperation for
> SPI support.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
> drivers/clk/Kconfig | 2 +-
> drivers/input/misc/Kconfig | 2 +-
> drivers/mfd/Kconfig | 7 +-
> drivers/mfd/Makefile | 3 +-
> drivers/mfd/{rk808.c => rk8xx-core.c} | 210 ++++----------------------
> drivers/mfd/rk8xx-i2c.c | 209 +++++++++++++++++++++++++
> drivers/pinctrl/Kconfig | 2 +-
> drivers/power/supply/Kconfig | 2 +-
> drivers/regulator/Kconfig | 2 +-
> drivers/rtc/Kconfig | 2 +-
> include/linux/mfd/rk808.h | 6 +
> sound/soc/codecs/Kconfig | 2 +-
> 12 files changed, 263 insertions(+), 186 deletions(-)
> rename drivers/mfd/{rk808.c => rk8xx-core.c} (75%)
> create mode 100644 drivers/mfd/rk8xx-i2c.c
>
> diff --git a/drivers/clk/Kconfig b/drivers/clk/Kconfig
> index d79905f3e174..8448d616b9aa 100644
> --- a/drivers/clk/Kconfig
> +++ b/drivers/clk/Kconfig
> @@ -83,7 +83,7 @@ config COMMON_CLK_MAX9485
>
> config COMMON_CLK_RK808
> tristate "Clock driver for RK805/RK808/RK809/RK817/RK818"
> - depends on MFD_RK808
> + depends on MFD_RK8XX
> help
> This driver supports RK805, RK809 and RK817, RK808 and RK818 crystal oscillator clock.
> These multi-function devices have two fixed-rate oscillators, clocked at 32KHz each.
> diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
> index 9f088900f863..1899afeaec47 100644
> --- a/drivers/input/misc/Kconfig
> +++ b/drivers/input/misc/Kconfig
> @@ -588,7 +588,7 @@ config INPUT_PWM_VIBRA
>
> config INPUT_RK805_PWRKEY
> tristate "Rockchip RK805 PMIC power key support"
> - depends on MFD_RK808
> + depends on MFD_RK8XX
> help
> Select this option to enable power key driver for RK805.
>
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 8b93856de432..8e3de443cc3d 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1201,12 +1201,17 @@ config MFD_RC5T583
> Additional drivers must be enabled in order to use the
> different functionality of the device.
>
> -config MFD_RK808
> +config MFD_RK8XX
> + bool
> + select MFD_CORE
> +
> +config MFD_RK8XX_I2C
> tristate "Rockchip RK805/RK808/RK809/RK817/RK818 Power Management Chip"
> depends on I2C && OF
> select MFD_CORE
> select REGMAP_I2C
> select REGMAP_IRQ
> + select MFD_RK8XX
> help
> If you say yes here you get support for the RK805, RK808, RK809,
> RK817 and RK818 Power Management chips.
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 7ed3ef4a698c..edf84e870f98 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -223,7 +223,8 @@ obj-$(CONFIG_MFD_PALMAS) += palmas.o
> obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
> obj-$(CONFIG_MFD_NTXEC) += ntxec.o
> obj-$(CONFIG_MFD_RC5T583) += rc5t583.o rc5t583-irq.o
> -obj-$(CONFIG_MFD_RK808) += rk808.o
> +obj-$(CONFIG_MFD_RK8XX) += rk8xx-core.o
> +obj-$(CONFIG_MFD_RK8XX_I2C) += rk8xx-i2c.o
> obj-$(CONFIG_MFD_RN5T618) += rn5t618.o
> obj-$(CONFIG_MFD_SEC_CORE) += sec-core.o sec-irq.o
> obj-$(CONFIG_MFD_SYSCON) += syscon.o
> diff --git a/drivers/mfd/rk808.c b/drivers/mfd/rk8xx-core.c
> similarity index 75%
> rename from drivers/mfd/rk808.c
> rename to drivers/mfd/rk8xx-core.c
> index b154ca96d812..098506972710 100644
> --- a/drivers/mfd/rk808.c
> +++ b/drivers/mfd/rk8xx-core.c
> @@ -3,16 +3,9 @@
> * MFD core driver for Rockchip RK808/RK818
> *
> * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
> - *
> - * Author: Chris Zhong <zyw@rock-chips.com>
> - * Author: Zhang Qing <zhangqing@rock-chips.com>
> - *
> * Copyright (C) 2016 PHYTEC Messtechnik GmbH
> - *
> - * Author: Wadim Egorov <w.egorov@phytec.de>
> */
The patch and the premise behind it look reasonable.
What's the reason for taking out the Author tags?
--
Lee Jones [李琼斯]
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 09/13] mfd: rk8xx: add rk806 support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-10-31 14:04 ` Lee Jones
-1 siblings, 0 replies; 44+ messages in thread
From: Lee Jones @ 2022-10-31 14:04 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, 20 Oct 2022, Sebastian Reichel wrote:
> Add support for SPI connected rk806, which is used by the RK3588
> evaluation boards. The PMIC is advertised to support I2C and SPI,
> but the evaluation boards all use SPI. Thus only SPI support is
> added here.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
Change log? What happened over the previous 4 iterations?
> drivers/mfd/Kconfig | 14 ++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/rk8xx-core.c | 67 ++++++-
> drivers/mfd/rk8xx-spi.c | 115 +++++++++++
> include/linux/mfd/rk808.h | 409 ++++++++++++++++++++++++++++++++++++++
> 5 files changed, 604 insertions(+), 2 deletions(-)
> create mode 100644 drivers/mfd/rk8xx-spi.c
[...]
> @@ -0,0 +1,115 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip RK806 Core (SPI) driver
> + *
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + *
> + * Author: Xu Shengfei <xsf@rock-chips.com>
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/rk808.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/spi/spi.h>
> +
> +static const struct regmap_range rk806_volatile_ranges[] = {
> + regmap_reg_range(RK806_POWER_EN0, RK806_POWER_EN5),
> + regmap_reg_range(RK806_DVS_START_CTRL, RK806_INT_MSK1),
> +};
> +
> +static const struct regmap_access_table rk806_volatile_table = {
> + .yes_ranges = rk806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(rk806_volatile_ranges),
> +};
> +
> +static const struct regmap_config rk806_regmap_config_spi = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_table = &rk806_volatile_table,
> +};
> +
> +static int rk806_spi_bus_write(void *context, const void *vdata, size_t count)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *data = vdata;
> + char buffer[4] = { 0 };
> +
> + /* implementation currently only supports single write */
> + if (count != 2)
> + return -EINVAL;
Is this a H/W limitation?
> + buffer[0] = RK806_CMD_WRITE | (count - 2);
> + buffer[1] = data[0]; /* register address */
You can make these clearer by defining the indexes.
> + buffer[2] = RK806_REG_H;
> + buffer[3] = data[1]; /* register value */
> +
> + return spi_write(spi, &buffer, sizeof(buffer));
> +}
> +
> +static int rk806_spi_bus_read(void *context, const void *vreg, size_t reg_size,
> + void *val, size_t val_size)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *reg = vreg;
> + char txbuf[3] = { 0 };
> +
> + if (reg_size != sizeof(char) || val_size < 1)
> + return -EINVAL;
> +
> + txbuf[0] = RK806_CMD_READ | (val_size - 1);
> + txbuf[1] = *reg;
> + txbuf[2] = RK806_REG_H;
> +
> + return spi_write_then_read(spi, txbuf, sizeof(txbuf), val, val_size);
> +}
> +
> +static const struct regmap_bus rk806_regmap_bus_spi = {
> + .write = rk806_spi_bus_write,
> + .read = rk806_spi_bus_read,
> + .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
> + .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
> +};
> +
> +static int rk8xx_spi_probe(struct spi_device *spi)
> +{
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init(&spi->dev, &rk806_regmap_bus_spi,
> + &spi->dev, &rk806_regmap_config_spi);
> + if (IS_ERR(regmap))
> + return dev_err_probe(&spi->dev, PTR_ERR(regmap),
> + "Failed to initialize register map\n");
> +
> + return rk8xx_probe(&spi->dev, RK806_ID, spi->irq, regmap);
> +}
> +
> +static const struct of_device_id rk8xx_spi_of_match[] = {
> + { .compatible = "rockchip,rk806", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, rk8xx_spi_of_match);
> +
> +static const struct spi_device_id rk8xx_spi_id_table[] = {
> + { "rk806", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(spi, rk8xx_spi_id_table);
Are these simple tables required for SPI?
Is there anything akin to I2C's probe_new that you could use?
> +static struct spi_driver rk8xx_spi_driver = {
> + .driver = {
> + .name = "rk8xx-spi",
> + .of_match_table = rk8xx_spi_of_match,
> + },
> + .probe = rk8xx_spi_probe,
> + .id_table = rk8xx_spi_id_table,
> +};
> +module_spi_driver(rk8xx_spi_driver);
> +
> +MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
> +MODULE_DESCRIPTION("RK8xx SPI PMIC driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
> index 4183427a80fe..78e167a92483 100644
> --- a/include/linux/mfd/rk808.h
> +++ b/include/linux/mfd/rk808.h
[...]
--
Lee Jones [李琼斯]
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 09/13] mfd: rk8xx: add rk806 support
@ 2022-10-31 14:04 ` Lee Jones
0 siblings, 0 replies; 44+ messages in thread
From: Lee Jones @ 2022-10-31 14:04 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski,
Michael Turquette, Stephen Boyd, Linus Walleij, Mark Brown,
Liam Girdwood, Alexandre Belloni, Alessandro Zummo,
linux-rockchip, devicetree, linux-kernel, kernel
On Thu, 20 Oct 2022, Sebastian Reichel wrote:
> Add support for SPI connected rk806, which is used by the RK3588
> evaluation boards. The PMIC is advertised to support I2C and SPI,
> but the evaluation boards all use SPI. Thus only SPI support is
> added here.
>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
Change log? What happened over the previous 4 iterations?
> drivers/mfd/Kconfig | 14 ++
> drivers/mfd/Makefile | 1 +
> drivers/mfd/rk8xx-core.c | 67 ++++++-
> drivers/mfd/rk8xx-spi.c | 115 +++++++++++
> include/linux/mfd/rk808.h | 409 ++++++++++++++++++++++++++++++++++++++
> 5 files changed, 604 insertions(+), 2 deletions(-)
> create mode 100644 drivers/mfd/rk8xx-spi.c
[...]
> @@ -0,0 +1,115 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Rockchip RK806 Core (SPI) driver
> + *
> + * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
> + *
> + * Author: Xu Shengfei <xsf@rock-chips.com>
> + */
> +
> +#include <linux/interrupt.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/rk808.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/spi/spi.h>
> +
> +static const struct regmap_range rk806_volatile_ranges[] = {
> + regmap_reg_range(RK806_POWER_EN0, RK806_POWER_EN5),
> + regmap_reg_range(RK806_DVS_START_CTRL, RK806_INT_MSK1),
> +};
> +
> +static const struct regmap_access_table rk806_volatile_table = {
> + .yes_ranges = rk806_volatile_ranges,
> + .n_yes_ranges = ARRAY_SIZE(rk806_volatile_ranges),
> +};
> +
> +static const struct regmap_config rk806_regmap_config_spi = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_table = &rk806_volatile_table,
> +};
> +
> +static int rk806_spi_bus_write(void *context, const void *vdata, size_t count)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *data = vdata;
> + char buffer[4] = { 0 };
> +
> + /* implementation currently only supports single write */
> + if (count != 2)
> + return -EINVAL;
Is this a H/W limitation?
> + buffer[0] = RK806_CMD_WRITE | (count - 2);
> + buffer[1] = data[0]; /* register address */
You can make these clearer by defining the indexes.
> + buffer[2] = RK806_REG_H;
> + buffer[3] = data[1]; /* register value */
> +
> + return spi_write(spi, &buffer, sizeof(buffer));
> +}
> +
> +static int rk806_spi_bus_read(void *context, const void *vreg, size_t reg_size,
> + void *val, size_t val_size)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + const char *reg = vreg;
> + char txbuf[3] = { 0 };
> +
> + if (reg_size != sizeof(char) || val_size < 1)
> + return -EINVAL;
> +
> + txbuf[0] = RK806_CMD_READ | (val_size - 1);
> + txbuf[1] = *reg;
> + txbuf[2] = RK806_REG_H;
> +
> + return spi_write_then_read(spi, txbuf, sizeof(txbuf), val, val_size);
> +}
> +
> +static const struct regmap_bus rk806_regmap_bus_spi = {
> + .write = rk806_spi_bus_write,
> + .read = rk806_spi_bus_read,
> + .reg_format_endian_default = REGMAP_ENDIAN_NATIVE,
> + .val_format_endian_default = REGMAP_ENDIAN_NATIVE,
> +};
> +
> +static int rk8xx_spi_probe(struct spi_device *spi)
> +{
> + struct regmap *regmap;
> +
> + regmap = devm_regmap_init(&spi->dev, &rk806_regmap_bus_spi,
> + &spi->dev, &rk806_regmap_config_spi);
> + if (IS_ERR(regmap))
> + return dev_err_probe(&spi->dev, PTR_ERR(regmap),
> + "Failed to initialize register map\n");
> +
> + return rk8xx_probe(&spi->dev, RK806_ID, spi->irq, regmap);
> +}
> +
> +static const struct of_device_id rk8xx_spi_of_match[] = {
> + { .compatible = "rockchip,rk806", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, rk8xx_spi_of_match);
> +
> +static const struct spi_device_id rk8xx_spi_id_table[] = {
> + { "rk806", 0 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(spi, rk8xx_spi_id_table);
Are these simple tables required for SPI?
Is there anything akin to I2C's probe_new that you could use?
> +static struct spi_driver rk8xx_spi_driver = {
> + .driver = {
> + .name = "rk8xx-spi",
> + .of_match_table = rk8xx_spi_of_match,
> + },
> + .probe = rk8xx_spi_probe,
> + .id_table = rk8xx_spi_id_table,
> +};
> +module_spi_driver(rk8xx_spi_driver);
> +
> +MODULE_AUTHOR("Xu Shengfei <xsf@rock-chips.com>");
> +MODULE_DESCRIPTION("RK8xx SPI PMIC driver");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/rk808.h b/include/linux/mfd/rk808.h
> index 4183427a80fe..78e167a92483 100644
> --- a/include/linux/mfd/rk808.h
> +++ b/include/linux/mfd/rk808.h
[...]
--
Lee Jones [李琼斯]
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCH v4 11/13] regulator: rk808: Use dev_err_probe
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-11-25 19:33 ` Mark Brown
-1 siblings, 0 replies; 44+ messages in thread
From: Mark Brown @ 2022-11-25 19:33 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Liam Girdwood,
Alexandre Belloni, Alessandro Zummo, linux-rockchip, devicetree,
linux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 316 bytes --]
On Thu, Oct 20, 2022 at 10:42:49PM +0200, Sebastian Reichel wrote:
> Print error message for potential EPROBE_DEFER error using
> dev_err_probe, which captures the reason in
> /sys/kernel/debug/devices_deferred and otherwise silences
> the message.
This doesn't apply against current code, please check and resend.
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCH v4 11/13] regulator: rk808: Use dev_err_probe
@ 2022-11-25 19:33 ` Mark Brown
0 siblings, 0 replies; 44+ messages in thread
From: Mark Brown @ 2022-11-25 19:33 UTC (permalink / raw)
To: Sebastian Reichel
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Liam Girdwood,
Alexandre Belloni, Alessandro Zummo, linux-rockchip, devicetree,
linux-kernel, kernel
[-- Attachment #1.1: Type: text/plain, Size: 316 bytes --]
On Thu, Oct 20, 2022 at 10:42:49PM +0200, Sebastian Reichel wrote:
> Print error message for potential EPROBE_DEFER error using
> dev_err_probe, which captures the reason in
> /sys/kernel/debug/devices_deferred and otherwise silences
> the message.
This doesn't apply against current code, please check and resend.
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]
[-- Attachment #2: Type: text/plain, Size: 170 bytes --]
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCH v4 11/13] regulator: rk808: Use dev_err_probe
2022-11-25 19:33 ` Mark Brown
@ 2022-11-25 23:46 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-11-25 23:46 UTC (permalink / raw)
To: Mark Brown
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Liam Girdwood,
Alexandre Belloni, Alessandro Zummo, linux-rockchip, devicetree,
linux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 758 bytes --]
Hi Mark,
On Fri, Nov 25, 2022 at 07:33:32PM +0000, Mark Brown wrote:
> On Thu, Oct 20, 2022 at 10:42:49PM +0200, Sebastian Reichel wrote:
> > Print error message for potential EPROBE_DEFER error using
> > dev_err_probe, which captures the reason in
> > /sys/kernel/debug/devices_deferred and otherwise silences
> > the message.
>
> This doesn't apply against current code, please check and resend.
That's expected. Patch 2 changes the dev parameter of dev_err(),
which is being changed to dev_err_probe() in this patch.
I think we are getting too close to the merge window for this
series considering it's touching so many subsystems. But you
can take patch 2 + 11 to the regulators tree as is.
Thanks for the review,
-- Sebastian
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCH v4 11/13] regulator: rk808: Use dev_err_probe
@ 2022-11-25 23:46 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-11-25 23:46 UTC (permalink / raw)
To: Mark Brown
Cc: Heiko Stuebner, Rob Herring, Krzysztof Kozlowski, Lee Jones,
Michael Turquette, Stephen Boyd, Linus Walleij, Liam Girdwood,
Alexandre Belloni, Alessandro Zummo, linux-rockchip, devicetree,
linux-kernel, kernel
[-- Attachment #1.1: Type: text/plain, Size: 758 bytes --]
Hi Mark,
On Fri, Nov 25, 2022 at 07:33:32PM +0000, Mark Brown wrote:
> On Thu, Oct 20, 2022 at 10:42:49PM +0200, Sebastian Reichel wrote:
> > Print error message for potential EPROBE_DEFER error using
> > dev_err_probe, which captures the reason in
> > /sys/kernel/debug/devices_deferred and otherwise silences
> > the message.
>
> This doesn't apply against current code, please check and resend.
That's expected. Patch 2 changes the dev parameter of dev_err(),
which is being changed to dev_err_probe() in this patch.
I think we are getting too close to the merge window for this
series considering it's touching so many subsystems. But you
can take patch 2 + 11 to the regulators tree as is.
Thanks for the review,
-- Sebastian
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 170 bytes --]
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 03/13] rtc: rk808: reduce 'struct rk808' usage
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-11-25 23:52 ` Sebastian Reichel
-1 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-11-25 23:52 UTC (permalink / raw)
To: Alexandre Belloni; +Cc: linux-rockchip, devicetree, linux-kernel, kernel
[-- Attachment #1: Type: text/plain, Size: 8927 bytes --]
Hi Alexandre,
On Thu, Oct 20, 2022 at 10:42:41PM +0200, Sebastian Reichel wrote:
> Reduce usage of 'struct rk808' (driver data of the parent MFD), so
> that only the chip variant field is still being accessed directly.
> This allows restructuring the MFD driver to support SPI based
> PMICs.
>
> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
You can take this patch. I don't think it makes sense to send
another version of this series before the merge window considering
it involves so many subystems. If the RTC patch is merged now it
does not need to become part of the immutable branch later :)
Thanks,
-- Sebastian
> drivers/rtc/rtc-rk808.c | 47 ++++++++++++++++++-----------------------
> 1 file changed, 20 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/rtc/rtc-rk808.c b/drivers/rtc/rtc-rk808.c
> index e920da8c08da..2d9bcb3ce1e3 100644
> --- a/drivers/rtc/rtc-rk808.c
> +++ b/drivers/rtc/rtc-rk808.c
> @@ -14,7 +14,6 @@
> #include <linux/bcd.h>
> #include <linux/mfd/rk808.h>
> #include <linux/platform_device.h>
> -#include <linux/i2c.h>
>
> /* RTC_CTRL_REG bitfields */
> #define BIT_RTC_CTRL_REG_STOP_RTC_M BIT(0)
> @@ -51,7 +50,7 @@ struct rk_rtc_compat_reg {
> };
>
> struct rk808_rtc {
> - struct rk808 *rk808;
> + struct regmap *regmap;
> struct rtc_device *rtc;
> struct rk_rtc_compat_reg *creg;
> int irq;
> @@ -97,12 +96,11 @@ static void gregorian_to_rockchip(struct rtc_time *tm)
> static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 rtc_data[NUM_TIME_REGS];
> int ret;
>
> /* Force an update of the shadowed registers right now */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_RTC_GET_TIME,
> BIT_RTC_CTRL_REG_RTC_GET_TIME);
> if (ret) {
> @@ -116,7 +114,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> * 32khz. If we clear the GET_TIME bit here, the time of i2c transfer
> * certainly more than 31.25us: 16 * 2.5us at 400kHz bus frequency.
> */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_RTC_GET_TIME,
> 0);
> if (ret) {
> @@ -124,7 +122,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> return ret;
> }
>
> - ret = regmap_bulk_read(rk808->regmap, rk808_rtc->creg->seconds_reg,
> + ret = regmap_bulk_read(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
> rtc_data, NUM_TIME_REGS);
> if (ret) {
> dev_err(dev, "Failed to bulk read rtc_data: %d\n", ret);
> @@ -148,7 +146,6 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 rtc_data[NUM_TIME_REGS];
> int ret;
>
> @@ -163,7 +160,7 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> rtc_data[6] = bin2bcd(tm->tm_wday);
>
> /* Stop RTC while updating the RTC registers */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M,
> BIT_RTC_CTRL_REG_STOP_RTC_M);
> if (ret) {
> @@ -171,14 +168,14 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> return ret;
> }
>
> - ret = regmap_bulk_write(rk808->regmap, rk808_rtc->creg->seconds_reg,
> + ret = regmap_bulk_write(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
> rtc_data, NUM_TIME_REGS);
> if (ret) {
> dev_err(dev, "Failed to bull write rtc_data: %d\n", ret);
> return ret;
> }
> /* Start RTC again */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M, 0);
> if (ret) {
> dev_err(dev, "Failed to update RTC control: %d\n", ret);
> @@ -191,12 +188,11 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 alrm_data[NUM_ALARM_REGS];
> uint32_t int_reg;
> int ret;
>
> - ret = regmap_bulk_read(rk808->regmap,
> + ret = regmap_bulk_read(rk808_rtc->regmap,
> rk808_rtc->creg->alarm_seconds_reg,
> alrm_data, NUM_ALARM_REGS);
> if (ret) {
> @@ -212,7 +208,7 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
> alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
> rockchip_to_gregorian(&alrm->time);
>
> - ret = regmap_read(rk808->regmap, rk808_rtc->creg->int_reg, &int_reg);
> + ret = regmap_read(rk808_rtc->regmap, rk808_rtc->creg->int_reg, &int_reg);
> if (ret) {
> dev_err(dev, "Failed to read RTC INT REG: %d\n", ret);
> return ret;
> @@ -228,10 +224,9 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
>
> static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
> {
> - struct rk808 *rk808 = rk808_rtc->rk808;
> int ret;
>
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M, 0);
>
> return ret;
> @@ -239,10 +234,9 @@ static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
>
> static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
> {
> - struct rk808 *rk808 = rk808_rtc->rk808;
> int ret;
>
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
>
> @@ -252,7 +246,6 @@ static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
> static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 alrm_data[NUM_ALARM_REGS];
> int ret;
>
> @@ -272,7 +265,7 @@ static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
> alrm_data[4] = bin2bcd(alrm->time.tm_mon + 1);
> alrm_data[5] = bin2bcd(alrm->time.tm_year - 100);
>
> - ret = regmap_bulk_write(rk808->regmap,
> + ret = regmap_bulk_write(rk808_rtc->regmap,
> rk808_rtc->creg->alarm_seconds_reg,
> alrm_data, NUM_ALARM_REGS);
> if (ret) {
> @@ -313,20 +306,18 @@ static int rk808_rtc_alarm_irq_enable(struct device *dev,
> static irqreturn_t rk808_alarm_irq(int irq, void *data)
> {
> struct rk808_rtc *rk808_rtc = data;
> - struct rk808 *rk808 = rk808_rtc->rk808;
> - struct i2c_client *client = rk808->i2c;
> int ret;
>
> - ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
> + ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
> RTC_STATUS_MASK);
> if (ret) {
> - dev_err(&client->dev,
> + dev_err(&rk808_rtc->rtc->dev,
> "%s:Failed to update RTC status: %d\n", __func__, ret);
> return ret;
> }
>
> rtc_update_irq(rk808_rtc->rtc, 1, RTC_IRQF | RTC_AF);
> - dev_dbg(&client->dev,
> + dev_dbg(&rk808_rtc->rtc->dev,
> "%s:irq=%d\n", __func__, irq);
> return IRQ_HANDLED;
> }
> @@ -404,10 +395,12 @@ static int rk808_rtc_probe(struct platform_device *pdev)
> break;
> }
> platform_set_drvdata(pdev, rk808_rtc);
> - rk808_rtc->rk808 = rk808;
> + rk808_rtc->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + if (!rk808_rtc->regmap)
> + return -ENODEV;
>
> /* start rtc running by default, and use shadowed timer. */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M |
> BIT_RTC_CTRL_REG_RTC_READSEL_M,
> BIT_RTC_CTRL_REG_RTC_READSEL_M);
> @@ -417,7 +410,7 @@ static int rk808_rtc_probe(struct platform_device *pdev)
> return ret;
> }
>
> - ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
> + ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
> RTC_STATUS_MASK);
> if (ret) {
> dev_err(&pdev->dev,
> --
> 2.35.1
>
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: [PATCHv4 03/13] rtc: rk808: reduce 'struct rk808' usage
@ 2022-11-25 23:52 ` Sebastian Reichel
0 siblings, 0 replies; 44+ messages in thread
From: Sebastian Reichel @ 2022-11-25 23:52 UTC (permalink / raw)
To: Alexandre Belloni; +Cc: linux-rockchip, devicetree, linux-kernel, kernel
[-- Attachment #1.1: Type: text/plain, Size: 8927 bytes --]
Hi Alexandre,
On Thu, Oct 20, 2022 at 10:42:41PM +0200, Sebastian Reichel wrote:
> Reduce usage of 'struct rk808' (driver data of the parent MFD), so
> that only the chip variant field is still being accessed directly.
> This allows restructuring the MFD driver to support SPI based
> PMICs.
>
> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
You can take this patch. I don't think it makes sense to send
another version of this series before the merge window considering
it involves so many subystems. If the RTC patch is merged now it
does not need to become part of the immutable branch later :)
Thanks,
-- Sebastian
> drivers/rtc/rtc-rk808.c | 47 ++++++++++++++++++-----------------------
> 1 file changed, 20 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/rtc/rtc-rk808.c b/drivers/rtc/rtc-rk808.c
> index e920da8c08da..2d9bcb3ce1e3 100644
> --- a/drivers/rtc/rtc-rk808.c
> +++ b/drivers/rtc/rtc-rk808.c
> @@ -14,7 +14,6 @@
> #include <linux/bcd.h>
> #include <linux/mfd/rk808.h>
> #include <linux/platform_device.h>
> -#include <linux/i2c.h>
>
> /* RTC_CTRL_REG bitfields */
> #define BIT_RTC_CTRL_REG_STOP_RTC_M BIT(0)
> @@ -51,7 +50,7 @@ struct rk_rtc_compat_reg {
> };
>
> struct rk808_rtc {
> - struct rk808 *rk808;
> + struct regmap *regmap;
> struct rtc_device *rtc;
> struct rk_rtc_compat_reg *creg;
> int irq;
> @@ -97,12 +96,11 @@ static void gregorian_to_rockchip(struct rtc_time *tm)
> static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 rtc_data[NUM_TIME_REGS];
> int ret;
>
> /* Force an update of the shadowed registers right now */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_RTC_GET_TIME,
> BIT_RTC_CTRL_REG_RTC_GET_TIME);
> if (ret) {
> @@ -116,7 +114,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> * 32khz. If we clear the GET_TIME bit here, the time of i2c transfer
> * certainly more than 31.25us: 16 * 2.5us at 400kHz bus frequency.
> */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_RTC_GET_TIME,
> 0);
> if (ret) {
> @@ -124,7 +122,7 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> return ret;
> }
>
> - ret = regmap_bulk_read(rk808->regmap, rk808_rtc->creg->seconds_reg,
> + ret = regmap_bulk_read(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
> rtc_data, NUM_TIME_REGS);
> if (ret) {
> dev_err(dev, "Failed to bulk read rtc_data: %d\n", ret);
> @@ -148,7 +146,6 @@ static int rk808_rtc_readtime(struct device *dev, struct rtc_time *tm)
> static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 rtc_data[NUM_TIME_REGS];
> int ret;
>
> @@ -163,7 +160,7 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> rtc_data[6] = bin2bcd(tm->tm_wday);
>
> /* Stop RTC while updating the RTC registers */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M,
> BIT_RTC_CTRL_REG_STOP_RTC_M);
> if (ret) {
> @@ -171,14 +168,14 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> return ret;
> }
>
> - ret = regmap_bulk_write(rk808->regmap, rk808_rtc->creg->seconds_reg,
> + ret = regmap_bulk_write(rk808_rtc->regmap, rk808_rtc->creg->seconds_reg,
> rtc_data, NUM_TIME_REGS);
> if (ret) {
> dev_err(dev, "Failed to bull write rtc_data: %d\n", ret);
> return ret;
> }
> /* Start RTC again */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M, 0);
> if (ret) {
> dev_err(dev, "Failed to update RTC control: %d\n", ret);
> @@ -191,12 +188,11 @@ static int rk808_rtc_set_time(struct device *dev, struct rtc_time *tm)
> static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 alrm_data[NUM_ALARM_REGS];
> uint32_t int_reg;
> int ret;
>
> - ret = regmap_bulk_read(rk808->regmap,
> + ret = regmap_bulk_read(rk808_rtc->regmap,
> rk808_rtc->creg->alarm_seconds_reg,
> alrm_data, NUM_ALARM_REGS);
> if (ret) {
> @@ -212,7 +208,7 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
> alrm->time.tm_year = (bcd2bin(alrm_data[5] & YEARS_REG_MSK)) + 100;
> rockchip_to_gregorian(&alrm->time);
>
> - ret = regmap_read(rk808->regmap, rk808_rtc->creg->int_reg, &int_reg);
> + ret = regmap_read(rk808_rtc->regmap, rk808_rtc->creg->int_reg, &int_reg);
> if (ret) {
> dev_err(dev, "Failed to read RTC INT REG: %d\n", ret);
> return ret;
> @@ -228,10 +224,9 @@ static int rk808_rtc_readalarm(struct device *dev, struct rtc_wkalrm *alrm)
>
> static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
> {
> - struct rk808 *rk808 = rk808_rtc->rk808;
> int ret;
>
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M, 0);
>
> return ret;
> @@ -239,10 +234,9 @@ static int rk808_rtc_stop_alarm(struct rk808_rtc *rk808_rtc)
>
> static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
> {
> - struct rk808 *rk808 = rk808_rtc->rk808;
> int ret;
>
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->int_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->int_reg,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M,
> BIT_RTC_INTERRUPTS_REG_IT_ALARM_M);
>
> @@ -252,7 +246,6 @@ static int rk808_rtc_start_alarm(struct rk808_rtc *rk808_rtc)
> static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
> {
> struct rk808_rtc *rk808_rtc = dev_get_drvdata(dev);
> - struct rk808 *rk808 = rk808_rtc->rk808;
> u8 alrm_data[NUM_ALARM_REGS];
> int ret;
>
> @@ -272,7 +265,7 @@ static int rk808_rtc_setalarm(struct device *dev, struct rtc_wkalrm *alrm)
> alrm_data[4] = bin2bcd(alrm->time.tm_mon + 1);
> alrm_data[5] = bin2bcd(alrm->time.tm_year - 100);
>
> - ret = regmap_bulk_write(rk808->regmap,
> + ret = regmap_bulk_write(rk808_rtc->regmap,
> rk808_rtc->creg->alarm_seconds_reg,
> alrm_data, NUM_ALARM_REGS);
> if (ret) {
> @@ -313,20 +306,18 @@ static int rk808_rtc_alarm_irq_enable(struct device *dev,
> static irqreturn_t rk808_alarm_irq(int irq, void *data)
> {
> struct rk808_rtc *rk808_rtc = data;
> - struct rk808 *rk808 = rk808_rtc->rk808;
> - struct i2c_client *client = rk808->i2c;
> int ret;
>
> - ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
> + ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
> RTC_STATUS_MASK);
> if (ret) {
> - dev_err(&client->dev,
> + dev_err(&rk808_rtc->rtc->dev,
> "%s:Failed to update RTC status: %d\n", __func__, ret);
> return ret;
> }
>
> rtc_update_irq(rk808_rtc->rtc, 1, RTC_IRQF | RTC_AF);
> - dev_dbg(&client->dev,
> + dev_dbg(&rk808_rtc->rtc->dev,
> "%s:irq=%d\n", __func__, irq);
> return IRQ_HANDLED;
> }
> @@ -404,10 +395,12 @@ static int rk808_rtc_probe(struct platform_device *pdev)
> break;
> }
> platform_set_drvdata(pdev, rk808_rtc);
> - rk808_rtc->rk808 = rk808;
> + rk808_rtc->regmap = dev_get_regmap(pdev->dev.parent, NULL);
> + if (!rk808_rtc->regmap)
> + return -ENODEV;
>
> /* start rtc running by default, and use shadowed timer. */
> - ret = regmap_update_bits(rk808->regmap, rk808_rtc->creg->ctrl_reg,
> + ret = regmap_update_bits(rk808_rtc->regmap, rk808_rtc->creg->ctrl_reg,
> BIT_RTC_CTRL_REG_STOP_RTC_M |
> BIT_RTC_CTRL_REG_RTC_READSEL_M,
> BIT_RTC_CTRL_REG_RTC_READSEL_M);
> @@ -417,7 +410,7 @@ static int rk808_rtc_probe(struct platform_device *pdev)
> return ret;
> }
>
> - ret = regmap_write(rk808->regmap, rk808_rtc->creg->status_reg,
> + ret = regmap_write(rk808_rtc->regmap, rk808_rtc->creg->status_reg,
> RTC_STATUS_MASK);
> if (ret) {
> dev_err(&pdev->dev,
> --
> 2.35.1
>
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 170 bytes --]
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: (subset) [PATCHv4 00/13] Introduce RK806 Support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-11-28 19:05 ` Mark Brown
-1 siblings, 0 replies; 44+ messages in thread
From: Mark Brown @ 2022-11-28 19:05 UTC (permalink / raw)
To: Rob Herring, Heiko Stuebner, Lee Jones, Krzysztof Kozlowski,
Sebastian Reichel
Cc: linux-kernel, kernel, Alexandre Belloni, Stephen Boyd,
Michael Turquette, Linus Walleij, devicetree, Liam Girdwood,
Alessandro Zummo, linux-rockchip
On Thu, 20 Oct 2022 22:42:38 +0200, Sebastian Reichel wrote:
> The Rockchip RK3588 Evaluation Boards use SPI connected RK806
> PMICs. Downstream this is handled by a new driver, but apart
> from being SPI connected this chip is quite similar to the
> ther Rockchip PMICs (also RK806 is promoted to also support
> I2C). Thus this series instead updates the RK808 driver(s).
>
> Changelog since PATCHv3:
> * https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
> * Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
> * Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
> since the patchset touches all the child drivers anyways.
> * rebase to v6.1-rc1
> * collected a couple of Acks
> * update rk806 DT binding according to DT maintainer feedback
> * add missing pinmux config to the rk806 DT binding
> * update rk806_spi_bus_write and rk806_spi_bus_read
> * replaced some constants with sizeof or defines
> * used capitalized comments
> * rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
> why I prefixed it with regmap_ in the first place
> * use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
> the switching regulators to correctly report the state
> * reordered the first few patches grouping the MFD patches together
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[02/13] regulator: rk808: reduce 'struct rk808' usage
commit: 647e57351f8ebc37d8e12cbc0f4bf7471754a0cc
[11/13] regulator: rk808: Use dev_err_probe
commit: f39f8709c217d82aabbf51d8669731137ce09aea
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: (subset) [PATCHv4 00/13] Introduce RK806 Support
@ 2022-11-28 19:05 ` Mark Brown
0 siblings, 0 replies; 44+ messages in thread
From: Mark Brown @ 2022-11-28 19:05 UTC (permalink / raw)
To: Rob Herring, Heiko Stuebner, Lee Jones, Krzysztof Kozlowski,
Sebastian Reichel
Cc: linux-kernel, kernel, Alexandre Belloni, Stephen Boyd,
Michael Turquette, Linus Walleij, devicetree, Liam Girdwood,
Alessandro Zummo, linux-rockchip
On Thu, 20 Oct 2022 22:42:38 +0200, Sebastian Reichel wrote:
> The Rockchip RK3588 Evaluation Boards use SPI connected RK806
> PMICs. Downstream this is handled by a new driver, but apart
> from being SPI connected this chip is quite similar to the
> ther Rockchip PMICs (also RK806 is promoted to also support
> I2C). Thus this series instead updates the RK808 driver(s).
>
> Changelog since PATCHv3:
> * https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
> * Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
> * Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
> since the patchset touches all the child drivers anyways.
> * rebase to v6.1-rc1
> * collected a couple of Acks
> * update rk806 DT binding according to DT maintainer feedback
> * add missing pinmux config to the rk806 DT binding
> * update rk806_spi_bus_write and rk806_spi_bus_read
> * replaced some constants with sizeof or defines
> * used capitalized comments
> * rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
> why I prefixed it with regmap_ in the first place
> * use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
> the switching regulators to correctly report the state
> * reordered the first few patches grouping the MFD patches together
>
> [...]
Applied to
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
Thanks!
[02/13] regulator: rk808: reduce 'struct rk808' usage
commit: 647e57351f8ebc37d8e12cbc0f4bf7471754a0cc
[11/13] regulator: rk808: Use dev_err_probe
commit: f39f8709c217d82aabbf51d8669731137ce09aea
All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent to Linus during
the next merge window (or sooner if it is a bug fix), however if
problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying
to this mail.
Thanks,
Mark
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: (subset) [PATCHv4 00/13] Introduce RK806 Support
2022-10-20 20:42 ` Sebastian Reichel
@ 2022-12-11 19:59 ` Alexandre Belloni
-1 siblings, 0 replies; 44+ messages in thread
From: Alexandre Belloni @ 2022-12-11 19:59 UTC (permalink / raw)
To: Heiko Stuebner, Krzysztof Kozlowski, Sebastian Reichel,
Lee Jones, Rob Herring
Cc: Liam Girdwood, Linus Walleij, Alessandro Zummo,
Michael Turquette, Stephen Boyd, kernel, linux-kernel,
Mark Brown, linux-rockchip, devicetree
On Thu, 20 Oct 2022 22:42:38 +0200, Sebastian Reichel wrote:
> The Rockchip RK3588 Evaluation Boards use SPI connected RK806
> PMICs. Downstream this is handled by a new driver, but apart
> from being SPI connected this chip is quite similar to the
> ther Rockchip PMICs (also RK806 is promoted to also support
> I2C). Thus this series instead updates the RK808 driver(s).
>
> Changelog since PATCHv3:
> * https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
> * Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
> * Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
> since the patchset touches all the child drivers anyways.
> * rebase to v6.1-rc1
> * collected a couple of Acks
> * update rk806 DT binding according to DT maintainer feedback
> * add missing pinmux config to the rk806 DT binding
> * update rk806_spi_bus_write and rk806_spi_bus_read
> * replaced some constants with sizeof or defines
> * used capitalized comments
> * rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
> why I prefixed it with regmap_ in the first place
> * use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
> the switching regulators to correctly report the state
> * reordered the first few patches grouping the MFD patches together
>
> [...]
Applied, thanks!
[03/13] rtc: rk808: reduce 'struct rk808' usage
commit: 2e830ccc21eb67a4c2490279d907e5e9199e5156
Best regards,
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
^ permalink raw reply [flat|nested] 44+ messages in thread
* Re: (subset) [PATCHv4 00/13] Introduce RK806 Support
@ 2022-12-11 19:59 ` Alexandre Belloni
0 siblings, 0 replies; 44+ messages in thread
From: Alexandre Belloni @ 2022-12-11 19:59 UTC (permalink / raw)
To: Heiko Stuebner, Krzysztof Kozlowski, Sebastian Reichel,
Lee Jones, Rob Herring
Cc: Liam Girdwood, Linus Walleij, Alessandro Zummo,
Michael Turquette, Stephen Boyd, kernel, linux-kernel,
Mark Brown, linux-rockchip, devicetree
On Thu, 20 Oct 2022 22:42:38 +0200, Sebastian Reichel wrote:
> The Rockchip RK3588 Evaluation Boards use SPI connected RK806
> PMICs. Downstream this is handled by a new driver, but apart
> from being SPI connected this chip is quite similar to the
> ther Rockchip PMICs (also RK806 is promoted to also support
> I2C). Thus this series instead updates the RK808 driver(s).
>
> Changelog since PATCHv3:
> * https://lore.kernel.org/all/20220909175522.179175-1-sebastian.reichel@collabora.com/
> * Dropped removing REGMAP_I2C dependency from RK817 ASoC driver (applied)
> * Rename MFD_RK808 to MFD_RK8XX to be consistent. It makes sense to do this now,
> since the patchset touches all the child drivers anyways.
> * rebase to v6.1-rc1
> * collected a couple of Acks
> * update rk806 DT binding according to DT maintainer feedback
> * add missing pinmux config to the rk806 DT binding
> * update rk806_spi_bus_write and rk806_spi_bus_read
> * replaced some constants with sizeof or defines
> * used capitalized comments
> * rename regmap_find_closest_bigger to regulator_find_closest_bigger, not sure
> why I prefixed it with regmap_ in the first place
> * use rk8xx_is_enabled_wmsk_regmap instead of regulator_is_enabled_regmap for
> the switching regulators to correctly report the state
> * reordered the first few patches grouping the MFD patches together
>
> [...]
Applied, thanks!
[03/13] rtc: rk808: reduce 'struct rk808' usage
commit: 2e830ccc21eb67a4c2490279d907e5e9199e5156
Best regards,
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
^ permalink raw reply [flat|nested] 44+ messages in thread
end of thread, other threads:[~2022-12-11 20:00 UTC | newest]
Thread overview: 44+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-10-20 20:42 [PATCHv4 00/13] Introduce RK806 Support Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 01/13] clk: RK808: reduce 'struct rk808' usage Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 02/13] regulator: rk808: " Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 03/13] rtc: " Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-11-25 23:52 ` Sebastian Reichel
2022-11-25 23:52 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 04/13] mfd: rk808: convert to device managed resources Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 05/13] mfd: rk808: use dev_err_probe Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 06/13] mfd: rk808: replace 'struct i2c_client' with 'struct device' Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 07/13] mfd: rk808: split into core and i2c Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-31 13:56 ` Lee Jones
2022-10-31 13:56 ` Lee Jones
2022-10-20 20:42 ` [PATCHv4 08/13] dt-bindings: mfd: add rk806 binding Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-21 22:19 ` Rob Herring
2022-10-21 22:19 ` Rob Herring
2022-10-20 20:42 ` [PATCHv4 09/13] mfd: rk8xx: add rk806 support Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-31 14:04 ` Lee Jones
2022-10-31 14:04 ` Lee Jones
2022-10-20 20:42 ` [PATCHv4 10/13] pinctrl: rk805: add rk806 pinctrl support Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 11/13] regulator: rk808: Use dev_err_probe Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-11-25 19:33 ` [PATCH v4 " Mark Brown
2022-11-25 19:33 ` Mark Brown
2022-11-25 23:46 ` Sebastian Reichel
2022-11-25 23:46 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 12/13] regulator: expose regulator_find_closest_bigger Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-10-20 20:42 ` [PATCHv4 13/13] regulator: rk808: add rk806 support Sebastian Reichel
2022-10-20 20:42 ` Sebastian Reichel
2022-11-28 19:05 ` (subset) [PATCHv4 00/13] Introduce RK806 Support Mark Brown
2022-11-28 19:05 ` Mark Brown
2022-12-11 19:59 ` Alexandre Belloni
2022-12-11 19:59 ` Alexandre Belloni
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.