From: Konrad Dybcio <konrad.dybcio@linaro.org>
To: linux-arm-msm@vger.kernel.org, andersson@kernel.org,
agross@kernel.org, krzysztof.kozlowski@linaro.org
Cc: patches@linaro.org, Konrad Dybcio <konrad.dybcio@linaro.org>,
Konrad Dybcio <konrad.dybcio@somainline.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH] arm64: dts: qcom: sm8450-nagara: Add gpio line names for TLMM
Date: Thu, 17 Nov 2022 15:16:13 +0100 [thread overview]
Message-ID: <20221117141613.19942-1-konrad.dybcio@linaro.org> (raw)
Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).
Add these to the PDX223&224 DTSIs to better document the hardware.
Diff between 223 and 224:
< gpio-line-names = "NC", /* GPIO_0 */
< "NC",
< "NC",
< "NC",
> gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
> "TELE_SPI_MOSI",
> "TELE_SPI_CLK",
> "TELE_SPI_CS_N",
< "PM8010_2_RESET_N",
> "NC",
< "NC",
> "UWIDEC_PWR_EN",
< "TOF_RST_N",
> "NC"
< "QLINK1_REQ",
< "QLINK1_EN", /* GPIO_160 */
< "QLINK1_WMSS_RESET_N",
> "NC",
> "NC", /* GPIO_160 */
> "NC",
The tele lens setup is different on 1 IV and 5 IV and power wiring
is different for some lenses, so it makes sense. As for QLINK, no
idea.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
.../qcom/sm8450-sony-xperia-nagara-pdx223.dts | 213 ++++++++++++++++++
.../qcom/sm8450-sony-xperia-nagara-pdx224.dts | 213 ++++++++++++++++++
2 files changed, 426 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
index 3ab145877094..b83500316a81 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
@@ -12,3 +12,216 @@ / {
model = "Sony Xperia 1 IV";
compatible = "sony,pdx223", "qcom,sm8450";
};
+
+&tlmm {
+ gpio-line-names = "NC", /* GPIO_0 */
+ "NC",
+ "NC",
+ "NC",
+ "WLC_I2C_SDA",
+ "WLC_I2C_SCL",
+ "NC",
+ "PM8010_1_RESET_N",
+ "WLC_INT_N",
+ "NC",
+ "NC", /* GPIO_10 */
+ "PM8010_2_RESET_N",
+ "DISP_ERR_FG",
+ "HALL_INT_N",
+ "ALS_PROX_INT_N",
+ "IMU1_INT",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "DISP_RESET_N",
+ "DISP_VDDR_EN",
+ "TS_RESET_N", /* GPIO_20 */
+ "TS_INT_N",
+ "NC",
+ "TELEC_PWR_EN",
+ "CAM1_RESET_N",
+ "LEO_CAM0_RESET_N",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_CLK", /* GPIO_30 */
+ "FP_SPI_CS_N",
+ "NFC_I2C_SDA",
+ "NFC_I2C_SCL",
+ "NFC_EN",
+ "NFC_CLK_REQ",
+ "NFC_ESE_SPI_MISO",
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_CLK",
+ "NFC_ESE_SPI_CS",
+ "FP_INT_N", /* GPIO_40 */
+ "NC",
+ "FP_RESET_N",
+ "WCD_RST_N",
+ "NC",
+ "NFC_DWL_REQ",
+ "NFC_IRQ",
+ "FORCE_USB_BOOT",
+ "APPS_I2C_1_SDA",
+ "APPS_I2C_1_SCL",
+ "SBU_SW_OE", /* GPIO_50 */
+ "SBU_SW_SEL",
+ "SPK_AMP_I2C_SDA",
+ "SPK_AMP_I2C_SCL",
+ "NC",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "GNSS_ELNA_EN0",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RGBC_IR_INT",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_70 */
+ "NC",
+ "HAP_I2C_SDA",
+ "HAP_I2C_SCL",
+ "HAP_RST_N",
+ "HAP_INT_N",
+ "HST_BT_UART_CTS",
+ "HST_BT_UART_RFR",
+ "HST_BT_UART_TX",
+ "HST_BT_UART_RX",
+ "HST_WLAN_EN", /* GPIO_80 */
+ "HST_BT_EN",
+ "HST_SW_CTRL",
+ "NC",
+ "NC",
+ "NC",
+ "DISP_VSYNC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "HW_ID_1", /* GPIO_90 */
+ "USB_CC_DIR",
+ "TRAY_DET",
+ "SW_SERVICE",
+ "PCIE0_RESET_N",
+ "PCIE0_CLK_REQ_N",
+ "PCIE0_WAKE_N",
+ "OIS_ENABLE_WIDE",
+ "DEBUG_GPIO0",
+ "NC",
+ "CAM_MCLK0", /* GPIO_100 */
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "NC",
+ "NC",
+ "TOF_RST_N",
+ "CAM_SOF",
+ "NC",
+ "AFEXPTMG_TELE",
+ "CCI_I2C0_SDA", /* GPIO_110 */
+ "CCI_I2C0_SCL",
+ "CCI_I2C1_SDA",
+ "CCI_I2C1_SCL",
+ "CCI_I2C2_SDA",
+ "CCI_I2C2_SCL",
+ "NC",
+ "CAM2_RESET_N",
+ "NC",
+ "EXT_VD0_XVS",
+ "CAM3_RESET_N", /* GPIO_120 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RF_ID_EXTENSION_2",
+ "HAP_I2S_CLK",
+ "HAP_I2S_DOUT",
+ "HAP_TRG1",
+ "HAP_I2S_SYNC",
+ "UIM1_DATA", /* GPIO_130 */
+ "UIM1_CLK",
+ "UIM1_RESET",
+ "TRAY_DET",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "SM_RFFE0_CLK",
+ "SM_RFFE0_DATA",
+ "SM_RFFE1_CLK", /* GPIO_140 */
+ "SM_RFFE1_DATA",
+ "SM_MSS_GRFC4",
+ "HST_AS_EN",
+ "LAA_RX_EN",
+ "NC",
+ "SM_RFFE4_CLK",
+ "SM_RFFE4_DATA",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "RF_LCD_ID_EN", /* GPIO_150 */
+ "RF_ID_EXTENSION",
+ "SM_MSS_GRFC12",
+ "NFC_COLD_RST",
+ "NC",
+ "NC",
+ "SDR1_QLINK0_REQ",
+ "SDR1_QLINK0_EN",
+ "SDR1_QLINK0_WMSS_RESET_N",
+ "QLINK1_REQ",
+ "QLINK1_EN", /* GPIO_160 */
+ "QLINK1_WMSS_RESET_N",
+ "SDR2_QLINK2_REQ",
+ "SDR2_QLINK2_EN",
+ "SDR2_QLINK2_WMSS_RESET_N",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1", /* GPIO_170 */
+ "SM_DMIC1_CLK",
+ "SM_DMIC1_DATA",
+ "SM_DMIC2_CLK",
+ "SM_DMIC2_DATA",
+ "SPK_AMP_I2S_CLK",
+ "SPK_AMP_I2S_WS",
+ "NC",
+ "NC",
+ "WCD_SWR_TX_DATA2",
+ "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+ "SPK_AMP_I2S_ASP_DOUT",
+ "SPK_AMP_INT_N",
+ "SPK_AMP_RESET_N",
+ "HST_BT_WLAN_SLIMBUS_CLK",
+ "HST_BT_WLAN_SLIMBUS_DAT0",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "MAG_I2C_SDA", /* GPIO_190 */
+ "MAG_I2C_SCL",
+ "IMU_SPI_MISO",
+ "IMU_SPI_MOSI",
+ "IMU_SPI_CLK",
+ "IMU_SPI_CS_N",
+ "SENSOR_I2C_SDA",
+ "SENSOR_I2C_SCL",
+ "OIS_TELE_I2C_SDA",
+ "OIS_TELE_I2C_SCL",
+ "NC", /* GPIO_200 */
+ "OIS_ENABLE_TELE",
+ "HST_BLE_UART_TX",
+ "HST_BLE_UART_RX",
+ "HSTP_CLK_CFG_SEL",
+ "NC",
+ "APPS_I2C_0_SDA",
+ "APPS_I2C_0_SCL",
+ "CCI_I2C3_SDA",
+ "CCI_I2C3_SCL";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
index 0d64d3c0afed..13c2fc4bccfc 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
@@ -19,3 +19,216 @@ imx563_vdig_vreg: imx563-vdig-regulator {
enable-active-high;
};
};
+
+&tlmm {
+ gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
+ "TELE_SPI_MOSI", /* SONY says NC, but it only makes sense this way.. */
+ "TELE_SPI_CLK",
+ "TELE_SPI_CS_N",
+ "WLC_I2C_SDA",
+ "WLC_I2C_SCL",
+ "NC",
+ "PM8010_1_RESET_N",
+ "WLC_INT_N",
+ "NC",
+ "NC", /* GPIO_10 */
+ "NC",
+ "DISP_ERR_FG",
+ "HALL_INT_N",
+ "ALS_PROX_INT_N",
+ "IMU1_INT",
+ "TS_I2C_SDA",
+ "TS_I2C_SCL",
+ "DISP_RESET_N",
+ "DISP_VDDR_EN",
+ "TS_RESET_N", /* GPIO_20 */
+ "TS_INT_N",
+ "UWIDEC_PWR_EN",
+ "TELEC_PWR_EN",
+ "CAM1_RESET_N",
+ "LEO_CAM0_RESET_N",
+ "DEBUG_UART_TX",
+ "DEBUG_UART_RX",
+ "FP_SPI_MISO",
+ "FP_SPI_MOSI",
+ "FP_SPI_CLK", /* GPIO_30 */
+ "FP_SPI_CS_N",
+ "NFC_I2C_SDA",
+ "NFC_I2C_SCL",
+ "NFC_EN",
+ "NFC_CLK_REQ",
+ "NFC_ESE_SPI_MISO",
+ "NFC_ESE_SPI_MOSI",
+ "NFC_ESE_SPI_CLK",
+ "NFC_ESE_SPI_CS",
+ "FP_INT_N", /* GPIO_40 */
+ "NC",
+ "FP_RESET_N",
+ "WCD_RST_N",
+ "NC",
+ "NFC_DWL_REQ",
+ "NFC_IRQ",
+ "FORCE_USB_BOOT",
+ "APPS_I2C_1_SDA",
+ "APPS_I2C_1_SCL",
+ "SBU_SW_OE", /* GPIO_50 */
+ "SBU_SW_SEL",
+ "SPK_AMP_I2C_SDA",
+ "SPK_AMP_I2C_SCL",
+ "NC",
+ "NC",
+ "CAMSENSOR_I2C_SDA",
+ "CAMSENSOR_I2C_SCL",
+ "GNSS_ELNA_EN0",
+ "NC",
+ "NC", /* GPIO_60 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RGBC_IR_INT",
+ "NC",
+ "NC",
+ "NC",
+ "NC", /* GPIO_70 */
+ "NC",
+ "HAP_I2C_SDA",
+ "HAP_I2C_SCL",
+ "HAP_RST_N",
+ "HAP_INT_N",
+ "HST_BT_UART_CTS",
+ "HST_BT_UART_RFR",
+ "HST_BT_UART_TX",
+ "HST_BT_UART_RX",
+ "HST_WLAN_EN", /* GPIO_80 */
+ "HST_BT_EN",
+ "HST_SW_CTRL",
+ "NC",
+ "NC",
+ "NC",
+ "DISP_VSYNC",
+ "NC",
+ "NC",
+ "HW_ID_0",
+ "HW_ID_1", /* GPIO_90 */
+ "USB_CC_DIR",
+ "TRAY_DET",
+ "SW_SERVICE",
+ "PCIE0_RESET_N",
+ "PCIE0_CLK_REQ_N",
+ "PCIE0_WAKE_N",
+ "OIS_ENABLE_WIDE",
+ "DEBUG_GPIO0",
+ "NC",
+ "CAM_MCLK0", /* GPIO_100 */
+ "CAM_MCLK1",
+ "CAM_MCLK2",
+ "CAM_MCLK3",
+ "NC",
+ "NC",
+ "NC", /* SONY didn't rename this, but there's no ToF so it's likely NC */
+ "CAM_SOF",
+ "NC",
+ "AFEXPTMG_TELE",
+ "CCI_I2C0_SDA", /* GPIO_110 */
+ "CCI_I2C0_SCL",
+ "CCI_I2C1_SDA",
+ "CCI_I2C1_SCL",
+ "CCI_I2C2_SDA",
+ "CCI_I2C2_SCL",
+ "NC",
+ "CAM2_RESET_N",
+ "NC",
+ "EXT_VD0_XVS",
+ "CAM3_RESET_N", /* GPIO_120 */
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "RF_ID_EXTENSION_2",
+ "HAP_I2S_CLK",
+ "HAP_I2S_DOUT",
+ "HAP_TRG1",
+ "HAP_I2S_SYNC",
+ "UIM1_DATA", /* GPIO_130 */
+ "UIM1_CLK",
+ "UIM1_RESET",
+ "TRAY_DET",
+ "UIM2_DATA",
+ "UIM2_CLK",
+ "UIM2_RESET",
+ "UIM2_PRESENT",
+ "SM_RFFE0_CLK",
+ "SM_RFFE0_DATA",
+ "SM_RFFE1_CLK", /* GPIO_140 */
+ "SM_RFFE1_DATA",
+ "SM_MSS_GRFC4",
+ "HST_AS_EN",
+ "LAA_RX_EN",
+ "NC",
+ "SM_RFFE4_CLK",
+ "SM_RFFE4_DATA",
+ "WLAN_COEX_UART1_RX",
+ "WLAN_COEX_UART1_TX",
+ "RF_LCD_ID_EN", /* GPIO_150 */
+ "RF_ID_EXTENSION",
+ "SM_MSS_GRFC12",
+ "NFC_COLD_RST",
+ "NC",
+ "NC",
+ "SDR1_QLINK0_REQ",
+ "SDR1_QLINK0_EN",
+ "SDR1_QLINK0_WMSS_RESET_N",
+ "NC",
+ "NC", /* GPIO_160 */
+ "NC",
+ "SDR2_QLINK2_REQ",
+ "SDR2_QLINK2_EN",
+ "SDR2_QLINK2_WMSS_RESET_N",
+ "WCD_SWR_TX_CLK",
+ "WCD_SWR_TX_DATA0",
+ "WCD_SWR_TX_DATA1",
+ "WCD_SWR_RX_CLK",
+ "WCD_SWR_RX_DATA0",
+ "WCD_SWR_RX_DATA1", /* GPIO_170 */
+ "SM_DMIC1_CLK",
+ "SM_DMIC1_DATA",
+ "SM_DMIC2_CLK",
+ "SM_DMIC2_DATA",
+ "SPK_AMP_I2S_CLK",
+ "SPK_AMP_I2S_WS",
+ "NC",
+ "NC",
+ "WCD_SWR_TX_DATA2",
+ "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+ "SPK_AMP_I2S_ASP_DOUT",
+ "SPK_AMP_INT_N",
+ "SPK_AMP_RESET_N",
+ "HST_BT_WLAN_SLIMBUS_CLK",
+ "HST_BT_WLAN_SLIMBUS_DAT0",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "MAG_I2C_SDA", /* GPIO_190 */
+ "MAG_I2C_SCL",
+ "IMU_SPI_MISO",
+ "IMU_SPI_MOSI",
+ "IMU_SPI_CLK",
+ "IMU_SPI_CS_N",
+ "SENSOR_I2C_SDA",
+ "SENSOR_I2C_SCL",
+ "OIS_TELE_I2C_SDA",
+ "OIS_TELE_I2C_SCL",
+ "NC", /* GPIO_200 */
+ "OIS_ENABLE_TELE",
+ "HST_BLE_UART_TX",
+ "HST_BLE_UART_RX",
+ "HSTP_CLK_CFG_SEL",
+ "NC",
+ "APPS_I2C_0_SDA",
+ "APPS_I2C_0_SCL",
+ "CCI_I2C3_SDA",
+ "CCI_I2C3_SCL";
+};
--
2.38.1
next reply other threads:[~2022-11-17 14:16 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-17 14:16 Konrad Dybcio [this message]
2022-12-06 18:19 ` [PATCH] arm64: dts: qcom: sm8450-nagara: Add gpio line names for TLMM Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221117141613.19942-1-konrad.dybcio@linaro.org \
--to=konrad.dybcio@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@somainline.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=patches@linaro.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.