From: Abel Vesa <abel.vesa@linaro.org>
To: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Sai Prakash Ranjan <quic_saipraka@quicinc.com>,
Neil Armstrong <neil.armstrong@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: [PATCH v3 09/10] arm64: dts: qcom: Add PMR735d pmic dtsi
Date: Sat, 26 Nov 2022 13:46:16 +0200 [thread overview]
Message-ID: <20221126114617.497677-10-abel.vesa@linaro.org> (raw)
In-Reply-To: <20221126114617.497677-1-abel.vesa@linaro.org>
From: Neil Armstrong <neil.armstrong@linaro.org>
Add nodes for PMR735d in separate dtsi file.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/pmr735d.dtsi | 104 ++++++++++++++++++++++++++
1 file changed, 104 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pmr735d.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pmr735d.dtsi b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
new file mode 100644
index 000000000000..41fb664a10b3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pmr735d.dtsi
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+ thermal-zones {
+ pmr735d-k-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmr735d_k_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+
+ pmr735d-l-thermal {
+ polling-delay-passive = <100>;
+ polling-delay = <0>;
+
+ thermal-sensors = <&pmr735d_l_temp_alarm>;
+
+ trips {
+ trip0 {
+ temperature = <95000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ trip1 {
+ temperature = <115000>;
+ hysteresis = <0>;
+ type = "hot";
+ };
+ };
+ };
+ };
+};
+
+
+&spmi_bus {
+ pmr735d_k: pmic@a {
+ compatible = "qcom,pmr735d", "qcom,spmi-pmic";
+ reg = <0xa SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmr735d_k_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0xa 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmr735d_k_gpios: gpio@8800 {
+ compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmr735d_k_gpios 0 0 2>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
+ pmr735d_l: pmic@b {
+ compatible = "qcom,pmr735d", "qcom,spmi-pmic";
+ reg = <0xb SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmr735d_l_temp_alarm: temp-alarm@a00 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0xa00>;
+ interrupts = <0xb 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ pmr735d_l_gpios: gpio@8800 {
+ compatible = "qcom,pmr735d-gpio", "qcom,spmi-gpio";
+ reg = <0x8800>;
+ gpio-controller;
+ gpio-ranges = <&pmr735d_l_gpios 0 0 2>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+};
--
2.34.1
next prev parent reply other threads:[~2022-11-26 11:48 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-11-26 11:46 [PATCH v3 00/10] arm64: dts: Add base device tree files for SM8550 Abel Vesa
2022-11-26 11:46 ` [PATCH v3 01/10] dt-bindings: arm: qcom: Document SM8550 SoC and boards Abel Vesa
2022-11-26 11:46 ` [PATCH v3 02/10] arm64: dts: qcom: Add base SM8550 dtsi Abel Vesa
2022-11-28 15:10 ` Konrad Dybcio
2022-11-26 11:46 ` [PATCH v3 03/10] arm64: dts: qcom: Add pm8010 pmic dtsi Abel Vesa
2022-11-26 11:46 ` [PATCH v3 04/10] arm64: dts: qcom: Add PM8550 " Abel Vesa
2022-11-26 11:46 ` [PATCH v3 05/10] arm64: dts: qcom: Add PM8550b " Abel Vesa
2022-11-26 11:46 ` [PATCH v3 06/10] arm64: dts: qcom: Add PM8550ve " Abel Vesa
2022-11-26 11:46 ` [PATCH v3 07/10] arm64: dts: qcom: Add PM8550vs " Abel Vesa
2022-11-26 11:46 ` [PATCH v3 08/10] arm64: dts: qcom: Add PMK8550 " Abel Vesa
2022-11-26 11:46 ` Abel Vesa [this message]
2022-11-26 11:46 ` [PATCH v3 10/10] arm64: dts: qcom: Add base SM8550 MTP dts Abel Vesa
2022-11-30 3:26 ` kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20221126114617.497677-10-abel.vesa@linaro.org \
--to=abel.vesa@linaro.org \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=neil.armstrong@linaro.org \
--cc=quic_saipraka@quicinc.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.