All of lore.kernel.org
 help / color / mirror / Atom feed
From: Abel Vesa <abel.vesa@linaro.org>
To: Andy Gross <agross@kernel.org>,
	Bjorn Andersson <andersson@kernel.org>,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
	Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: [PATCH v2 1/2] arm64: dts: qcom: sm8550: Add PCIe PHYs and controllers nodes
Date: Thu, 19 Jan 2023 01:05:25 +0200	[thread overview]
Message-ID: <20230118230526.1499328-2-abel.vesa@linaro.org> (raw)
In-Reply-To: <20230118230526.1499328-1-abel.vesa@linaro.org>

Add PCIe controllers and PHY nodes.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 213 ++++++++++++++++++++++++++-
 1 file changed, 210 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 3d47281a276b..a78068cbf95f 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -646,9 +646,9 @@ gcc: clock-controller@100000 {
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			clocks = <&bi_tcxo_div2>, <&sleep_clk>,
-				 <0>,
-				 <0>,
-				 <0>,
+				 <&pcie0_phy>,
+				 <&pcie1_phy>,
+				 <&pcie_1_phy_aux_clk>,
 				 <&ufs_mem_phy 0>,
 				 <&ufs_mem_phy 1>,
 				 <&ufs_mem_phy 2>,
@@ -1547,6 +1547,213 @@ mmss_noc: interconnect@1780000 {
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pcie0: pci@1c00000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8550";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <0>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "aggre0";
+
+			interconnect-names = "pcie-mem";
+			interconnects = <&pcie_noc MASTER_PCIE_0 0 &mc_virt SLAVE_EBI1 0>;
+
+			iommus = <&apps_smmu 0x1400 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1400 0x1>,
+				    <0x100 &apps_smmu 0x1401 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			phys = <&pcie0_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie0_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8550-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c06000 0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_0_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie0_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		pcie1: pci@1c08000 {
+			device_type = "pci";
+			compatible = "qcom,pcie-sm8550";
+			reg = <0x0 0x01c08000 0x0 0x3000>,
+			      <0x0 0x40000000 0x0 0xf1d>,
+			      <0x0 0x40000f20 0x0 0xa8>,
+			      <0x0 0x40001000 0x0 0x1000>,
+			      <0x0 0x40100000 0x0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
+			bus-range = <0x00 0xff>;
+
+			dma-coherent;
+
+			linux,pci-domain = <1>;
+			num-lanes = <2>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_QTB_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_AXI_CLK>,
+				 <&gcc GCC_CNOC_PCIE_SF_AXI_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "aggre1",
+				      "cnoc_pcie_sf_axi";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			interconnect-names = "pcie-mem";
+			interconnects = <&pcie_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI1 0>;
+
+			iommus = <&apps_smmu 0x1480 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1480 0x1>,
+				    <0x100 &apps_smmu 0x1481 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>,
+				<&gcc GCC_PCIE_1_LINK_DOWN_BCR>;
+			reset-names = "pci",
+				"pcie_1_link_down_reset";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_phy>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+			enable-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8550-qmp-gen4x2-pcie-phy";
+			reg = <0x0 0x01c0e000 0x0 0x2000>;
+
+			clocks = <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&tcsr TCSR_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_PHY_AUX_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "rchng",
+				      "pipe", "aux_phy";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>,
+				 <&gcc GCC_PCIE_1_NOCSR_COM_PHY_BCR>;
+			reset-names = "phy", "nocsr";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			power-domains = <&gcc PCIE_1_PHY_GDSC>;
+
+			#clock-cells = <0>;
+			clock-output-names = "pcie1_pipe_clk";
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		cryptobam: dma-controller@1dc4000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x0 0x01dc4000 0x0 0x28000>;
-- 
2.34.1


  reply	other threads:[~2023-01-18 23:05 UTC|newest]

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-01-18 23:05 [PATCH v2 0/2] arm64: dts: qcom: sm8550: Add PCIe HC and PHY support Abel Vesa
2023-01-18 23:05 ` Abel Vesa [this message]
2023-01-18 23:05 ` [PATCH v2 2/2] arm64: dts: qcom: sm8550-mtp: Add PCIe PHYs and controllers nodes Abel Vesa
2023-01-18 23:55 ` [PATCH v2 0/2] arm64: dts: qcom: sm8550: Add PCIe HC and PHY support Bjorn Andersson
2023-01-19  7:33   ` Johan Hovold
2023-01-19 12:09     ` Abel Vesa
2023-01-19 12:29       ` Krzysztof Kozlowski
2023-01-19 12:50         ` Abel Vesa

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230118230526.1499328-2-abel.vesa@linaro.org \
    --to=abel.vesa@linaro.org \
    --cc=agross@kernel.org \
    --cc=andersson@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=konrad.dybcio@linaro.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.