From: Rahul T R <r-ravikumar@ti.com>
To: Sinthu Raja <sinthu.raja@mistralsolutions.com>
Cc: Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Vignesh Raghavendra <vigneshr@ti.com>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
<linux-arm-kernel@lists.infradead.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Sinthu Raja <sinthu.raja@ti.com>
Subject: Re: [PATCH V2 2/2] arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header
Date: Thu, 26 Jan 2023 01:34:28 +0530 [thread overview]
Message-ID: <20230125200427.2bqlpym5tzz43yqq@uda0490373> (raw)
In-Reply-To: <20230124120311.7323-3-sinthu.raja@ti.com>
On 17:33-20230124, Sinthu Raja wrote:
> From: Sinthu Raja <sinthu.raja@ti.com>
>
> Add pinmux required to bring out the i2c and gpios on 40-pin RPi
> expansion header on the AM68 SK board.
>
> Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
> ---
>
> No Changes in V2.
>
> .../boot/dts/ti/k3-am68-sk-base-board.dts | 70 ++++++++++++++++++-
> 1 file changed, 69 insertions(+), 1 deletion(-)
>
Tested-by: Rahul T R <r-ravikumar@ti.com>
> diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> index 2091cd2431fb..722cd19b74e0 100644
> --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts
> @@ -173,6 +173,32 @@ J721S2_IOPAD(0x0a0, PIN_INPUT, 0) /* (AB25) MCASP0_AXR12.MCAN7_RX */
> J721S2_IOPAD(0x09c, PIN_INPUT, 0) /* (T24) MCASP0_AXR11.MCAN7_TX */
> >;
> };
> +
> + main_i2c4_pins_default: main-i2c4-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x010, PIN_INPUT_PULLUP, 7) /* (AF28) MCAN13_RX.I2C4_SDA */
> + J721S2_IOPAD(0x014, PIN_INPUT_PULLUP, 7) /* (AD25) MCAN14_TX.I2C4_SCL */
> + >;
> + };
> +
> + rpi_header_gpio0_pins_default: rpi-header-gpio0-pins-default {
> + pinctrl-single,pins = <
> + J721S2_IOPAD(0x0a8, PIN_INPUT, 7) /* (U24) MCASP0_AXR14.GPIO0_42 */
> + J721S2_IOPAD(0x090, PIN_INPUT, 7) /* (W24) MCASP0_AXR8.GPIO0_36 */
> + J721S2_IOPAD(0x0bc, PIN_INPUT, 7) /* (V28) MCASP1_AFSX.GPIO0_47 */
> + J721S2_IOPAD(0x06c, PIN_INPUT, 7) /* (V26) MCAN1_TX.GPIO0_27 */
> + J721S2_IOPAD(0x004, PIN_INPUT, 7) /* (W25) MCAN12_TX.GPIO0_1 */
> + J721S2_IOPAD(0x008, PIN_INPUT, 7) /* (AC24) MCAN12_RX.GPIO0_2 */
> + J721S2_IOPAD(0x0b8, PIN_INPUT, 7) /* (AA24) MCASP1_ACLKX.GPIO0_46 */
> + J721S2_IOPAD(0x00c, PIN_INPUT, 7) /* (AE28) MCAN13_TX.GPIO0_3 */
> + J721S2_IOPAD(0x034, PIN_INPUT, 7) /* (AD24) PMIC_WAKE0.GPIO0_13 */
> + J721S2_IOPAD(0x0a4, PIN_INPUT, 7) /* (T23) MCASP0_AXR13.GPIO0_41 */
> + J721S2_IOPAD(0x0c0, PIN_INPUT, 7) /* (T28) MCASP1_AXR0.GPIO0_48 */
> + J721S2_IOPAD(0x0b4, PIN_INPUT, 7) /* (U25) MCASP1_AXR4.GPIO0_45 */
> + J721S2_IOPAD(0x0cc, PIN_INPUT, 7) /* (AE27) SPI0_CS0.GPIO0_51 */
> + J721S2_IOPAD(0x08c, PIN_INPUT, 7) /* (T25) MCASP0_AXR7.GPIO0_35 */
> + >;
> + };
> };
>
> &wkup_pmx0 {
> @@ -214,12 +240,39 @@ J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX*/
> >;
> };
>
> + mcu_i2c0_pins_default: mcu-i2c0-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x100, PIN_INPUT, 0) /*(H24) WKUP_GPIO0_63.MCU_I2C0_SCL*/
> + J721S2_WKUP_IOPAD(0x104, PIN_INPUT, 0) /*(H27) WKUP_GPIO0_64.MCU_I2C0_SDA*/
> + >;
> + };
> +
> mcu_i2c1_pins_default: mcu-i2c1-pins-default {
> pinctrl-single,pins = <
> J721S2_WKUP_IOPAD(0x0e0, PIN_INPUT, 0) /* (F24) WKUP_GPIO0_8.MCU_I2C1_SCL */
> J721S2_WKUP_IOPAD(0x0e4, PIN_INPUT, 0) /* (H26) WKUP_GPIO0_9.MCU_I2C1_SDA */
> >;
> };
> +
> + mcu_rpi_header_gpio0_pins_default: mcu-rpi-header-gpio0-pins-default {
> + pinctrl-single,pins = <
> + J721S2_WKUP_IOPAD(0x180, PIN_INPUT, 7) /* (G25) WKUP_GPIO0_66 */
> + J721S2_WKUP_IOPAD(0x190, PIN_INPUT, 7) /* (K26) WKUP_GPIO0_49 */
> + J721S2_WKUP_IOPAD(0x0c4, PIN_INPUT, 7) /* (E24) MCU_SPI1_D0.WKUP_GPIO0_1 */
> + J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) MCU_SPI1_D1.WKUP_GPIO0_2 */
> + J721S2_WKUP_IOPAD(0x0c0, PIN_INPUT, 7) /* (D26) MCU_SPI1_CLK.WKUP_GPIO0_0 */
> + J721S2_WKUP_IOPAD(0x0fc, PIN_INPUT, 7) /* (D25) MCU_SPI1_CS2.WKUP_GPIO0_15*/
> + J721S2_WKUP_IOPAD(0x120, PIN_INPUT, 7) /* (G27) WKUP_GPIO0_56 */
> + J721S2_WKUP_IOPAD(0x17c, PIN_INPUT, 7) /* (J26) WKUP_GPIO0_57 */
> + J721S2_WKUP_IOPAD(0x184, PIN_INPUT, 7) /* (J27) WKUP_GPIO0_67 */
> + J721S2_WKUP_IOPAD(0x0cc, PIN_INPUT, 7) /* (C27) MCU_SPI1_CS0.WKUP_GPIO0_3 */
> + >;
> + };
> +};
> +
> +&main_gpio0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&rpi_header_gpio0_pins_default>;
> };
>
> &main_gpio2 {
> @@ -235,7 +288,8 @@ &main_gpio6 {
> };
>
> &wkup_gpio0 {
> - status = "disabled";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_rpi_header_gpio0_pins_default>;
> };
>
> &wkup_gpio1 {
> @@ -273,6 +327,20 @@ exp1: gpio@21 {
> };
> };
>
> +&main_i2c4 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_i2c4_pins_default>;
> + clock-frequency = <400000>;
> +};
> +
> +&mcu_i2c0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&mcu_i2c0_pins_default>;
> + clock-frequency = <400000>;
> +};
> +
> &main_sdhci0 {
> /* Unused */
> status = "disabled";
> --
> 2.36.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2023-01-25 20:04 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-24 12:03 [PATCH V2 0/2] Fix WKUP domain IO PADCONFIG size issue and RPi header support Sinthu Raja
2023-01-24 12:03 ` Sinthu Raja
2023-01-24 12:03 ` [PATCH V2 1/2] arm64: dts: ti: k3-j721s2-mcu-wakeup: Fix IO PADCONFIG size for wakeup domain Sinthu Raja
2023-01-24 12:03 ` Sinthu Raja
2023-01-24 12:03 ` [PATCH V2 2/2] arm64: dts: ti: k3-am68-sk-base-board: Add pinmux for RPi Header Sinthu Raja
2023-01-24 12:03 ` Sinthu Raja
2023-01-25 20:04 ` Rahul T R [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230125200427.2bqlpym5tzz43yqq@uda0490373 \
--to=r-ravikumar@ti.com \
--cc=devicetree@vger.kernel.org \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=sinthu.raja@mistralsolutions.com \
--cc=sinthu.raja@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.