From: Manorit Chawdhry <m-chawdhry@ti.com>
To: <u-boot@lists.denx.de>
Cc: Andrew Davis <afd@ti.com>, Manorit Chawdhry <m-chawdhry@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Neha Francis <n-francis@ti.com>,
Jayesh Choudhary <j-choudhary@ti.com>
Subject: [PATCH v2 1/2] configs: j721s2: merge HS and non-HS defconfigs
Date: Fri, 24 Feb 2023 10:37:48 +0530 [thread overview]
Message-ID: <20230224050749.13145-1-m-chawdhry@ti.com> (raw)
K3 devices have runtime type board detection. Make the default defconfig
include the secure configuration. Then remove the HS specific config.
Non-HS devices will continue to boot due to runtime device type detection.
If TI_SECURE_DEV_PKG is not set the build will emit warnings, for non-HS
devices these can be ignored.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
---
v1->v2:
update MAINTAINERS
MAINTAINERS | 2 -
configs/j721s2_evm_a72_defconfig | 3 +-
configs/j721s2_evm_r5_defconfig | 1 +
configs/j721s2_hs_evm_a72_defconfig | 213 ----------------------------
configs/j721s2_hs_evm_r5_defconfig | 176 -----------------------
5 files changed, 3 insertions(+), 392 deletions(-)
delete mode 100644 configs/j721s2_hs_evm_a72_defconfig
delete mode 100644 configs/j721s2_hs_evm_r5_defconfig
diff --git a/MAINTAINERS b/MAINTAINERS
index b9c505d5faa7..bdea0704adc0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1457,8 +1457,6 @@ F: configs/j7200_hs_evm_a72_defconfig
F: configs/j7200_hs_evm_r5_defconfig
F: configs/j721e_hs_evm_a72_defconfig
F: configs/j721e_hs_evm_r5_defconfig
-F: configs/j721s2_hs_evm_a72_defconfig
-F: configs/j721s2_hs_evm_r5_defconfig
TPM DRIVERS
M: Ilias Apalodimas <ilias.apalodimas@linaro.org>
diff --git a/configs/j721s2_evm_a72_defconfig b/configs/j721s2_evm_a72_defconfig
index 84b4fb083191..c880a8d37158 100644
--- a/configs/j721s2_evm_a72_defconfig
+++ b/configs/j721s2_evm_a72_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
CONFIG_SYS_MALLOC_LEN=0x2000000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_SPL_GPIO=y
@@ -32,7 +33,7 @@ CONFIG_SPL_LOAD_FIT=y
CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
# CONFIG_USE_SPL_FIT_GENERATOR is not set
CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern"
+CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; if test ${boot_fit} -eq 1; then run get_fit_${boot}; run get_overlaystring; run run_fit; else; run get_kern_${boot}; run get_fdt_${boot}; run get_overlay_${boot}; run run_kern; fi;"
CONFIG_LOGLEVEL=7
CONFIG_SPL_MAX_SIZE=0xc0000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
diff --git a/configs/j721s2_evm_r5_defconfig b/configs/j721s2_evm_r5_defconfig
index 1f2102a9f91f..51f2da66c9d1 100644
--- a/configs/j721s2_evm_r5_defconfig
+++ b/configs/j721s2_evm_r5_defconfig
@@ -1,5 +1,6 @@
CONFIG_ARM=y
CONFIG_ARCH_K3=y
+CONFIG_TI_SECURE_DEVICE=y
CONFIG_SYS_MALLOC_LEN=0x2000000
CONFIG_SYS_MALLOC_F_LEN=0x10000
CONFIG_SPL_GPIO=y
diff --git a/configs/j721s2_hs_evm_a72_defconfig b/configs/j721s2_hs_evm_a72_defconfig
deleted file mode 100644
index 9fc90737da80..000000000000
--- a/configs/j721s2_hs_evm_a72_defconfig
+++ /dev/null
@@ -1,213 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x8000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_NR_DRAM_BANKS=2
-CONFIG_SOC_K3_J721S2=y
-CONFIG_TARGET_J721S2_A72_EVM=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_ENV_OFFSET=0x680000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j721s2-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x80080000
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_ENV_OFFSET_REDUND=0x6A0000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-# CONFIG_PSCI_RESET is not set
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80480000
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
-# CONFIG_USE_SPL_FIT_GENERATOR is not set
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_BOOTCOMMAND="run findfdt; run envboot; run init_${boot}; run boot_rprocs; run get_fit_${boot}; run get_overlaystring; run run_fit"
-CONFIG_LOGLEVEL=7
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x80a00000
-CONFIG_SPL_BSS_MAX_SIZE=0x80000
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_SYS_SPL_MALLOC_SIZE=0x800000
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000
-CONFIG_SPL_THERMAL=y
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_GPT=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_MTD=y
-CONFIG_CMD_REMOTEPROC=y
-CONFIG_CMD_UFS=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_MTDIDS_DEFAULT="nor0=47040000.spi.0,nor0=47034000.hyperbus"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=47040000.spi.0:512k(ospi.tiboot3),2m(ospi.tispl),4m(ospi.u-boot),256k(ospi.env),256k(ospi.env.backup),57088k@8m(ospi.rootfs),256k(ospi.phypattern);47034000.hyperbus:512k(hbmc.tiboot3),2m(hbmc.tispl),4m(hbmc.u-boot),256k(hbmc.env),-@8m(hbmc.rootfs)"
-CONFIG_CMD_UBI=y
-# CONFIG_ISO_PARTITION is not set
-# CONFIG_SPL_EFI_PARTITION is not set
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SPL_MULTI_DTB_FIT=y
-CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y
-CONFIG_ENV_OVERWRITE=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RANDOM_ETHADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_CLK_CCF=y
-CONFIG_CLK_TI_SCI=y
-CONFIG_DFU_MMC=y
-CONFIG_DFU_RAM=y
-CONFIG_DFU_SF=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_USB_FUNCTION_FASTBOOT=y
-CONFIG_FASTBOOT_BUF_ADDR=0x82000000
-CONFIG_FASTBOOT_BUF_SIZE=0x2F000000
-CONFIG_FASTBOOT_FLASH=y
-CONFIG_FASTBOOT_FLASH_MMC_DEV=0
-CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_DM_I2C_GPIO=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_MMC_IO_VOLTAGE=y
-CONFIG_MMC_UHS_SUPPORT=y
-CONFIG_MMC_HS400_SUPPORT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_MMC_SDHCI_ADMA=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_SOFT_RESET=y
-CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_MT35XU=y
-# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
-CONFIG_SPI_FLASH_MTD=y
-CONFIG_MULTIPLEXER=y
-CONFIG_MUX_MMIO=y
-CONFIG_PHY_TI_DP83867=y
-CONFIG_PHY_FIXED=y
-CONFIG_TI_AM65_CPSW_NUSS=y
-CONFIG_PHY=y
-CONFIG_SPL_PHY=y
-CONFIG_PHY_CADENCE_TORRENT=y
-CONFIG_PHY_J721E_WIZ=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_SCI_POWER_DOMAIN=y
-CONFIG_DM_REGULATOR=y
-CONFIG_DM_REGULATOR_FIXED=y
-CONFIG_DM_REGULATOR_GPIO=y
-CONFIG_RAM=y
-CONFIG_SPL_RAM=y
-CONFIG_REMOTEPROC_TI_K3_DSP=y
-CONFIG_REMOTEPROC_TI_K3_R5F=y
-CONFIG_DM_RESET=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_SCSI=y
-CONFIG_DM_SCSI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_DM_THERMAL=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_USB_CDNS3_HOST=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6168
-CONFIG_UFS=y
-CONFIG_CADENCE_UFS=y
-CONFIG_TI_J721E_UFS=y
-CONFIG_OF_LIBFDT_OVERLAY=y
diff --git a/configs/j721s2_hs_evm_r5_defconfig b/configs/j721s2_hs_evm_r5_defconfig
deleted file mode 100644
index d9988fc17fc7..000000000000
--- a/configs/j721s2_hs_evm_r5_defconfig
+++ /dev/null
@@ -1,176 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_K3=y
-CONFIG_TI_SECURE_DEVICE=y
-CONFIG_SYS_MALLOC_LEN=0x2000000
-CONFIG_SYS_MALLOC_F_LEN=0x10000
-CONFIG_SPL_GPIO=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_SOC_K3_J721S2=y
-CONFIG_K3_EARLY_CONS=y
-CONFIG_TARGET_J721S2_R5_EVM=y
-CONFIG_ENV_SIZE=0x20000
-CONFIG_DM_GPIO=y
-CONFIG_SPL_DM_SPI=y
-CONFIG_DEFAULT_DEVICE_TREE="k3-j721s2-r5-common-proc-board"
-CONFIG_SPL_TEXT_BASE=0x41c00000
-CONFIG_SPL_MMC=y
-CONFIG_SPL_SERIAL=y
-CONFIG_SPL_DRIVERS_MISC=y
-CONFIG_SPL_STACK_R_ADDR=0x82000000
-CONFIG_SPL_SIZE_LIMIT=0x80000
-CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000
-CONFIG_SPL_FS_FAT=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-CONFIG_SPL_SPI_FLASH_SUPPORT=y
-CONFIG_SPL_SPI=y
-CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
-CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x41c76000
-# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
-CONFIG_SPL_LOAD_FIT=y
-CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000
-# CONFIG_USE_SPL_FIT_GENERATOR is not set
-CONFIG_USE_BOOTCOMMAND=y
-# CONFIG_DISPLAY_CPUINFO is not set
-CONFIG_SPL_SIZE_LIMIT_SUBTRACT_GD=y
-CONFIG_SPL_SIZE_LIMIT_SUBTRACT_MALLOC=y
-CONFIG_SPL_MAX_SIZE=0xc0000
-CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
-CONFIG_SPL_BSS_START_ADDR=0x41c76000
-CONFIG_SPL_BSS_MAX_SIZE=0xa000
-CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_SYS_MALLOC_SIMPLE=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_SEPARATE_BSS=y
-CONFIG_SYS_SPL_MALLOC=y
-CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
-CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x84000000
-CONFIG_SYS_SPL_MALLOC_SIZE=0x1000000
-CONFIG_SPL_EARLY_BSS=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
-CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x400
-CONFIG_SPL_DMA=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_FS_EXT4=y
-CONFIG_SPL_I2C=y
-CONFIG_SPL_DM_MAILBOX=y
-CONFIG_SPL_MTD_SUPPORT=y
-CONFIG_SPL_DM_SPI_FLASH=y
-CONFIG_SPL_NOR_SUPPORT=y
-CONFIG_SPL_DM_RESET=y
-CONFIG_SPL_POWER_DOMAIN=y
-CONFIG_SPL_RAM_SUPPORT=y
-CONFIG_SPL_RAM_DEVICE=y
-CONFIG_SPL_REMOTEPROC=y
-# CONFIG_SPL_SPI_FLASH_TINY is not set
-CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPL_SPI_LOAD=y
-CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
-CONFIG_SPL_THERMAL=y
-CONFIG_SPL_USB_GADGET=y
-CONFIG_SPL_DFU=y
-CONFIG_SPL_YMODEM_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_MAXARGS=64
-CONFIG_SYS_BOOTM_LEN=0x4000000
-CONFIG_CMD_DFU=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPT=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_REMOTEPROC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_TIME=y
-CONFIG_CMD_FAT=y
-CONFIG_OF_CONTROL=y
-CONFIG_SPL_OF_CONTROL=y
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_SPL_DM=y
-CONFIG_SPL_DM_SEQ_ALIAS=y
-CONFIG_REGMAP=y
-CONFIG_SPL_REGMAP=y
-CONFIG_SYSCON=y
-CONFIG_SPL_SYSCON=y
-CONFIG_SPL_OF_TRANSLATE=y
-CONFIG_CLK=y
-CONFIG_SPL_CLK=y
-CONFIG_SPL_CLK_CCF=y
-CONFIG_SPL_CLK_K3_PLL=y
-CONFIG_SPL_CLK_K3=y
-CONFIG_SYS_DFU_DATA_BUF_SIZE=0x40000
-CONFIG_DMA_CHANNELS=y
-CONFIG_TI_K3_NAVSS_UDMA=y
-CONFIG_TI_SCI_PROTOCOL=y
-CONFIG_DA8XX_GPIO=y
-CONFIG_DM_PCA953X=y
-CONFIG_DM_I2C=y
-CONFIG_I2C_SET_DEFAULT_BUS_NUM=y
-CONFIG_SYS_I2C_OMAP24XX=y
-CONFIG_DM_MAILBOX=y
-CONFIG_K3_SEC_PROXY=y
-CONFIG_FS_LOADER=y
-CONFIG_SPL_FS_LOADER=y
-CONFIG_SUPPORT_EMMC_BOOT=y
-CONFIG_SPL_MMC_HS400_SUPPORT=y
-CONFIG_MMC_SDHCI=y
-CONFIG_SPL_MMC_SDHCI_ADMA=y
-CONFIG_MMC_SDHCI_AM654=y
-CONFIG_MTD=y
-CONFIG_DM_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_FLASH_SHOW_PROGRESS=0
-CONFIG_CFI_FLASH=y
-CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
-CONFIG_FLASH_CFI_MTD=y
-CONFIG_SYS_FLASH_CFI=y
-CONFIG_SYS_MAX_FLASH_BANKS_DETECT=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_SFDP_SUPPORT=y
-CONFIG_SPI_FLASH_SOFT_RESET=y
-CONFIG_SPI_FLASH_SOFT_RESET_ON_BOOT=y
-CONFIG_SPI_FLASH_SPANSION=y
-CONFIG_SPI_FLASH_STMICRO=y
-CONFIG_SPI_FLASH_MT35XU=y
-CONFIG_PINCTRL=y
-# CONFIG_PINCTRL_GENERIC is not set
-CONFIG_SPL_PINCTRL=y
-# CONFIG_SPL_PINCTRL_GENERIC is not set
-CONFIG_PINCTRL_SINGLE=y
-CONFIG_POWER_DOMAIN=y
-CONFIG_TI_POWER_DOMAIN=y
-CONFIG_K3_SYSTEM_CONTROLLER=y
-CONFIG_REMOTEPROC_TI_K3_ARM64=y
-CONFIG_DM_RESET=y
-CONFIG_RESET_TI_SCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_SOC_DEVICE=y
-CONFIG_SOC_DEVICE_TI_K3=y
-CONFIG_SOC_TI=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_CADENCE_QSPI=y
-CONFIG_HAS_CQSPI_REF_CLK=y
-CONFIG_CQSPI_REF_CLK=133333333
-CONFIG_SYSRESET=y
-CONFIG_SPL_SYSRESET=y
-CONFIG_SYSRESET_TI_SCI=y
-CONFIG_DM_THERMAL=y
-CONFIG_TIMER=y
-CONFIG_SPL_TIMER=y
-CONFIG_OMAP_TIMER=y
-CONFIG_USB=y
-CONFIG_DM_USB_GADGET=y
-CONFIG_SPL_DM_USB_GADGET=y
-CONFIG_USB_CDNS3=y
-CONFIG_USB_CDNS3_GADGET=y
-CONFIG_SPL_USB_CDNS3_GADGET=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0451
-CONFIG_USB_GADGET_PRODUCT_NUM=0x6168
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_FS_EXT4=y
-CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
-CONFIG_PANIC_HANG=y
-CONFIG_LIB_RATIONAL=y
-CONFIG_SPL_LIB_RATIONAL=y
--
2.34.1
next reply other threads:[~2023-02-24 5:08 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-02-24 5:07 Manorit Chawdhry [this message]
2023-02-24 5:07 ` [PATCH v2 2/2] configs: j7200: Merge HS and non-HS defconfigs Manorit Chawdhry
2023-03-07 17:53 ` Tom Rini
2023-03-07 17:52 ` [PATCH v2 1/2] configs: j721s2: merge " Tom Rini
2023-03-14 8:28 ` Manorit Chawdhry
2023-03-14 14:54 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230224050749.13145-1-m-chawdhry@ti.com \
--to=m-chawdhry@ti.com \
--cc=afd@ti.com \
--cc=j-choudhary@ti.com \
--cc=n-francis@ti.com \
--cc=u-boot@lists.denx.de \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.