* [Patch v3] 0/7] Remove mach-kirkwood
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
This is mostly a resend of these patches, removing mach-kirkwood. Not
all maintainers picked up there patches, which has resulted in some
dead kernel configuration in v3.17-rcX.
The patch set has been rebased on v3.17-rc2, and it is intended that
Jason Cooper will submit them for inclusion in an RC. Subsystem
maintainers do not need to do anything.
The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
since what it is removing was added during v3.16-rcX. It follows the
pattern of all the other patches.
Andrew Lunn (7):
cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
ata: Remove ARCH_KIRKWOOD dependency
thermal: Remove ARCH_KIRKWOOD dependency
leds: Remove ARCH_KIRKWOOD dependency
rtc: Remove ARCH_KIRKWOOD dependency
watchdog: Remove ARCH_KIRKWOOD dependency
cpufreq: Remove ARCH_KIRKWOOD dependency
drivers/ata/Kconfig | 2 +-
drivers/cpufreq/Kconfig.arm | 2 +-
drivers/cpuidle/Kconfig.arm | 2 +-
drivers/leds/Kconfig | 4 ++--
drivers/rtc/Kconfig | 2 +-
drivers/thermal/Kconfig | 2 +-
drivers/watchdog/Kconfig | 2 +-
7 files changed, 8 insertions(+), 8 deletions(-)
--
2.1.0
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm at vger.kernel.org
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide at vger.kernel.org
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm at vger.kernel.org
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds at vger.kernel.org
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux at googlegroups.com
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog at vger.kernel.org
Cc: Viresh Kumar <viresh.kumar@linaro.org>
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: Jason Cooper
Cc: linux ARM, Andrew Lunn, Daniel Lezcano, Rafael J. Wysocki, linux-pm
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD, which is set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
---
drivers/cpuidle/Kconfig.arm | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
index 38cff69ffe06..58bcd0d166ec 100644
--- a/drivers/cpuidle/Kconfig.arm
+++ b/drivers/cpuidle/Kconfig.arm
@@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE
config ARM_KIRKWOOD_CPUIDLE
bool "CPU Idle Driver for Marvell Kirkwood SoCs"
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
help
This adds the CPU Idle driver for Marvell Kirkwood SoCs.
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD, which is set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm at vger.kernel.org
---
drivers/cpuidle/Kconfig.arm | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
index 38cff69ffe06..58bcd0d166ec 100644
--- a/drivers/cpuidle/Kconfig.arm
+++ b/drivers/cpuidle/Kconfig.arm
@@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE
config ARM_KIRKWOOD_CPUIDLE
bool "CPU Idle Driver for Marvell Kirkwood SoCs"
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
help
This adds the CPU Idle driver for Marvell Kirkwood SoCs.
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* Re: [Patch v3] 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-09-03 13:45 ` Daniel Lezcano
-1 siblings, 0 replies; 29+ messages in thread
From: Daniel Lezcano @ 2014-09-03 13:45 UTC (permalink / raw)
To: Andrew Lunn, Jason Cooper; +Cc: linux ARM, Rafael J. Wysocki, linux-pm
On 08/30/2014 06:46 PM, Andrew Lunn wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> Use MACH_KIRKWOOD, which is set when kirkwood is built as part of
> mach-mvebu.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
> Cc: linux-pm@vger.kernel.org
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
> ---
> drivers/cpuidle/Kconfig.arm | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
> index 38cff69ffe06..58bcd0d166ec 100644
> --- a/drivers/cpuidle/Kconfig.arm
> +++ b/drivers/cpuidle/Kconfig.arm
> @@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE
>
> config ARM_KIRKWOOD_CPUIDLE
> bool "CPU Idle Driver for Marvell Kirkwood SoCs"
> - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
> + depends on MACH_KIRKWOOD
> help
> This adds the CPU Idle driver for Marvell Kirkwood SoCs.
>
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 1/7] cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
@ 2014-09-03 13:45 ` Daniel Lezcano
0 siblings, 0 replies; 29+ messages in thread
From: Daniel Lezcano @ 2014-09-03 13:45 UTC (permalink / raw)
To: linux-arm-kernel
On 08/30/2014 06:46 PM, Andrew Lunn wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> Use MACH_KIRKWOOD, which is set when kirkwood is built as part of
> mach-mvebu.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
> Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
> Cc: linux-pm at vger.kernel.org
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
> ---
> drivers/cpuidle/Kconfig.arm | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/cpuidle/Kconfig.arm b/drivers/cpuidle/Kconfig.arm
> index 38cff69ffe06..58bcd0d166ec 100644
> --- a/drivers/cpuidle/Kconfig.arm
> +++ b/drivers/cpuidle/Kconfig.arm
> @@ -28,7 +28,7 @@ config ARM_HIGHBANK_CPUIDLE
>
> config ARM_KIRKWOOD_CPUIDLE
> bool "CPU Idle Driver for Marvell Kirkwood SoCs"
> - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
> + depends on MACH_KIRKWOOD
> help
> This adds the CPU Idle driver for Marvell Kirkwood SoCs.
>
>
--
<http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 2/7] ata: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: Jason Cooper; +Cc: linux ARM, Andrew Lunn, Tejun Heo, linux-ide
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
---
drivers/ata/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index e1b92788c225..cd4cccbfd2ab 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -299,7 +299,7 @@ config SATA_HIGHBANK
config SATA_MV
tristate "Marvell SATA support"
- depends on PCI || ARCH_DOVE || ARCH_KIRKWOOD || ARCH_MV78XX0 || \
+ depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST
select GENERIC_PHY
help
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 2/7] ata: Remove ARCH_KIRKWOOD dependency
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide at vger.kernel.org
---
drivers/ata/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index e1b92788c225..cd4cccbfd2ab 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -299,7 +299,7 @@ config SATA_HIGHBANK
config SATA_MV
tristate "Marvell SATA support"
- depends on PCI || ARCH_DOVE || ARCH_KIRKWOOD || ARCH_MV78XX0 || \
+ depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST
select GENERIC_PHY
help
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* Re: [Patch v3] 2/7] ata: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-31 11:02 ` Tejun Heo
-1 siblings, 0 replies; 29+ messages in thread
From: Tejun Heo @ 2014-08-31 11:02 UTC (permalink / raw)
To: Andrew Lunn; +Cc: Jason Cooper, linux ARM, linux-ide
On Sat, Aug 30, 2014 at 06:46:07PM +0200, Andrew Lunn wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> ARCH_MVEBU is sufficient.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Tejun Heo <tj@kernel.org>
> Cc: linux-ide@vger.kernel.org
Acked-by: Tejun Heo <tj@kernel.org>
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 2/7] ata: Remove ARCH_KIRKWOOD dependency
@ 2014-08-31 11:02 ` Tejun Heo
0 siblings, 0 replies; 29+ messages in thread
From: Tejun Heo @ 2014-08-31 11:02 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Aug 30, 2014 at 06:46:07PM +0200, Andrew Lunn wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> ARCH_MVEBU is sufficient.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Tejun Heo <tj@kernel.org>
> Cc: linux-ide at vger.kernel.org
Acked-by: Tejun Heo <tj@kernel.org>
Thanks.
--
tejun
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 3/7] thermal: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: Jason Cooper; +Cc: linux ARM, Andrew Lunn, Zhang Rui, linux-pm
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
part of ARCH_MVEBU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
---
drivers/thermal/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 693208eb9047..ef5587fe2c69 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -143,7 +143,7 @@ config RCAR_THERMAL
config KIRKWOOD_THERMAL
tristate "Temperature sensor on Marvell Kirkwood SoCs"
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
depends on OF
help
Support for the Kirkwood thermal sensor driver into the Linux thermal
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 3/7] thermal: Remove ARCH_KIRKWOOD dependency
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
part of ARCH_MVEBU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm at vger.kernel.org
---
drivers/thermal/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 693208eb9047..ef5587fe2c69 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -143,7 +143,7 @@ config RCAR_THERMAL
config KIRKWOOD_THERMAL
tristate "Temperature sensor on Marvell Kirkwood SoCs"
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
depends on OF
help
Support for the Kirkwood thermal sensor driver into the Linux thermal
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* Re: [Patch v3] 3/7] thermal: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-09-02 11:53 ` edubezval at gmail.com
-1 siblings, 0 replies; 29+ messages in thread
From: edubezval @ 2014-09-02 11:53 UTC (permalink / raw)
To: Andrew Lunn; +Cc: Jason Cooper, linux ARM, Zhang Rui, linux-pm
Andrew,
On Sat, Aug 30, 2014 at 12:46 PM, Andrew Lunn <andrew@lunn.ch> wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
> part of ARCH_MVEBU.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Zhang Rui <rui.zhang@intel.com>
> Cc: linux-pm@vger.kernel.org
> ---
> drivers/thermal/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 693208eb9047..ef5587fe2c69 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -143,7 +143,7 @@ config RCAR_THERMAL
>
> config KIRKWOOD_THERMAL
> tristate "Temperature sensor on Marvell Kirkwood SoCs"
> - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
> + depends on MACH_KIRKWOOD
I have no objections with this change. So, wrt thermal:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
> depends on OF
> help
> Support for the Kirkwood thermal sensor driver into the Linux thermal
> --
> 2.1.0
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pm" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Eduardo Bezerra Valentin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 3/7] thermal: Remove ARCH_KIRKWOOD dependency
@ 2014-09-02 11:53 ` edubezval at gmail.com
0 siblings, 0 replies; 29+ messages in thread
From: edubezval at gmail.com @ 2014-09-02 11:53 UTC (permalink / raw)
To: linux-arm-kernel
Andrew,
On Sat, Aug 30, 2014 at 12:46 PM, Andrew Lunn <andrew@lunn.ch> wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> Depend on MACH_KIRKWOOD, which will be set when kirkwood is built as
> part of ARCH_MVEBU.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: Zhang Rui <rui.zhang@intel.com>
> Cc: linux-pm at vger.kernel.org
> ---
> drivers/thermal/Kconfig | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 693208eb9047..ef5587fe2c69 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -143,7 +143,7 @@ config RCAR_THERMAL
>
> config KIRKWOOD_THERMAL
> tristate "Temperature sensor on Marvell Kirkwood SoCs"
> - depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
> + depends on MACH_KIRKWOOD
I have no objections with this change. So, wrt thermal:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
> depends on OF
> help
> Support for the Kirkwood thermal sensor driver into the Linux thermal
> --
> 2.1.0
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pm" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
Eduardo Bezerra Valentin
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 4/7] leds: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: Jason Cooper; +Cc: linux ARM, Andrew Lunn, Richard Purdie, linux-leds
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD which will be set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
---
drivers/leds/Kconfig | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 8c96e2ddf43b..f6ef7bb2dc11 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -410,7 +410,7 @@ config LEDS_MC13783
config LEDS_NS2
tristate "LED support for Network Space v2 GPIO LEDs"
depends on LEDS_CLASS
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
default y
help
This option enable support for the dual-GPIO LED found on the
@@ -420,7 +420,7 @@ config LEDS_NS2
config LEDS_NETXBIG
tristate "LED support for Big Network series LEDs"
depends on LEDS_CLASS
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
default y
help
This option enable support for LEDs found on the LaCie 2Big
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 4/7] leds: Remove ARCH_KIRKWOOD dependency
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
Use MACH_KIRKWOOD which will be set when kirkwood is built as part of
mach-mvebu.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Bryan Wu <cooloney@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds at vger.kernel.org
---
drivers/leds/Kconfig | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index 8c96e2ddf43b..f6ef7bb2dc11 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -410,7 +410,7 @@ config LEDS_MC13783
config LEDS_NS2
tristate "LED support for Network Space v2 GPIO LEDs"
depends on LEDS_CLASS
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
default y
help
This option enable support for the dual-GPIO LED found on the
@@ -420,7 +420,7 @@ config LEDS_NS2
config LEDS_NETXBIG
tristate "LED support for Big Network series LEDs"
depends on LEDS_CLASS
- depends on ARCH_KIRKWOOD || MACH_KIRKWOOD
+ depends on MACH_KIRKWOOD
default y
help
This option enable support for LEDs found on the LaCie 2Big
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 5/7] rtc: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
` (4 preceding siblings ...)
(?)
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux at googlegroups.com
---
drivers/rtc/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index a168e96142b9..fae9464eed9c 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1198,7 +1198,7 @@ config RTC_DRV_TX4939
config RTC_DRV_MV
tristate "Marvell SoC RTC"
- depends on ARCH_KIRKWOOD || ARCH_DOVE || ARCH_MVEBU
+ depends on ARCH_DOVE || ARCH_MVEBU
help
If you say yes here you will get support for the in-chip RTC
that can be found in some of Marvell's SoC devices, such as
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 6/7] watchdog: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
@ 2014-08-30 16:46 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: Jason Cooper; +Cc: linux ARM, Andrew Lunn, Wim Van Sebroeck, linux-watchdog
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
---
drivers/watchdog/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index f57312fced80..1d1330a78af3 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -301,7 +301,7 @@ config DAVINCI_WATCHDOG
config ORION_WATCHDOG
tristate "Orion watchdog"
- depends on ARCH_ORION5X || ARCH_KIRKWOOD || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU
+ depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 6/7] watchdog: Remove ARCH_KIRKWOOD dependency
@ 2014-08-30 16:46 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog at vger.kernel.org
---
drivers/watchdog/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index f57312fced80..1d1330a78af3 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -301,7 +301,7 @@ config DAVINCI_WATCHDOG
config ORION_WATCHDOG
tristate "Orion watchdog"
- depends on ARCH_ORION5X || ARCH_KIRKWOOD || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU
+ depends on ARCH_ORION5X || ARCH_DOVE || MACH_DOVE || ARCH_MVEBU
select WATCHDOG_CORE
help
Say Y here if to include support for the watchdog timer
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 7/7] cpufreq: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` Andrew Lunn
` (6 preceding siblings ...)
(?)
@ 2014-08-30 16:46 ` Andrew Lunn
2014-09-01 4:05 ` Viresh Kumar
-1 siblings, 1 reply; 29+ messages in thread
From: Andrew Lunn @ 2014-08-30 16:46 UTC (permalink / raw)
To: linux-arm-kernel
mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
ARCH_MVEBU is sufficient.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
---
drivers/cpufreq/Kconfig.arm | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index 7364a538e056..8c5cf4bdeab8 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -119,7 +119,7 @@ config ARM_INTEGRATOR
If in doubt, say Y.
config ARM_KIRKWOOD_CPUFREQ
- def_bool ARCH_KIRKWOOD || MACH_KIRKWOOD
+ def_bool MACH_KIRKWOOD
help
This adds the CPUFreq driver for Marvell Kirkwood
SoCs.
--
2.1.0
^ permalink raw reply related [flat|nested] 29+ messages in thread
* [Patch v3] 7/7] cpufreq: Remove ARCH_KIRKWOOD dependency
2014-08-30 16:46 ` [Patch v3] 7/7] cpufreq: " Andrew Lunn
@ 2014-09-01 4:05 ` Viresh Kumar
0 siblings, 0 replies; 29+ messages in thread
From: Viresh Kumar @ 2014-09-01 4:05 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Aug 30, 2014 at 10:16 PM, Andrew Lunn <andrew@lunn.ch> wrote:
> mach-kirkwood has been removed, now that kirkwood lives in mach-mvebu.
> ARCH_MVEBU is sufficient.
>
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
> Cc: Viresh Kumar <viresh.kumar@linaro.org>
> ---
> drivers/cpufreq/Kconfig.arm | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
> index 7364a538e056..8c5cf4bdeab8 100644
> --- a/drivers/cpufreq/Kconfig.arm
> +++ b/drivers/cpufreq/Kconfig.arm
> @@ -119,7 +119,7 @@ config ARM_INTEGRATOR
> If in doubt, say Y.
>
> config ARM_KIRKWOOD_CPUFREQ
> - def_bool ARCH_KIRKWOOD || MACH_KIRKWOOD
> + def_bool MACH_KIRKWOOD
> help
> This adds the CPUFreq driver for Marvell Kirkwood
> SoCs.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
^ permalink raw reply [flat|nested] 29+ messages in thread
* Re: [Patch v3] 0/7] Remove mach-kirkwood
2014-08-30 16:46 ` Andrew Lunn
@ 2014-09-01 13:56 ` Rafael J. Wysocki
-1 siblings, 0 replies; 29+ messages in thread
From: Rafael J. Wysocki @ 2014-09-01 13:56 UTC (permalink / raw)
To: Andrew Lunn
Cc: Jason Cooper, linux ARM, Daniel Lezcano, linux-pm, Tejun Heo,
linux-ide, Zhang Rui, Richard Purdie, linux-leds,
Alessandro Zummo, rtc-linux, Wim Van Sebroeck, linux-watchdog,
Viresh Kumar
On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> This is mostly a resend of these patches, removing mach-kirkwood. Not
> all maintainers picked up there patches, which has resulted in some
> dead kernel configuration in v3.17-rcX.
>
> The patch set has been rebased on v3.17-rc2, and it is intended that
> Jason Cooper will submit them for inclusion in an RC. Subsystem
> maintainers do not need to do anything.
>
> The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> since what it is removing was added during v3.16-rcX. It follows the
> pattern of all the other patches.
>
> Andrew Lunn (7):
> cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> ata: Remove ARCH_KIRKWOOD dependency
> thermal: Remove ARCH_KIRKWOOD dependency
> leds: Remove ARCH_KIRKWOOD dependency
> rtc: Remove ARCH_KIRKWOOD dependency
> watchdog: Remove ARCH_KIRKWOOD dependency
> cpufreq: Remove ARCH_KIRKWOOD dependency
I have no problems with these changes, but what exactly am I supposed to do?
Rafael
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 0/7] Remove mach-kirkwood
@ 2014-09-01 13:56 ` Rafael J. Wysocki
0 siblings, 0 replies; 29+ messages in thread
From: Rafael J. Wysocki @ 2014-09-01 13:56 UTC (permalink / raw)
To: linux-arm-kernel
On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> This is mostly a resend of these patches, removing mach-kirkwood. Not
> all maintainers picked up there patches, which has resulted in some
> dead kernel configuration in v3.17-rcX.
>
> The patch set has been rebased on v3.17-rc2, and it is intended that
> Jason Cooper will submit them for inclusion in an RC. Subsystem
> maintainers do not need to do anything.
>
> The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> since what it is removing was added during v3.16-rcX. It follows the
> pattern of all the other patches.
>
> Andrew Lunn (7):
> cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> ata: Remove ARCH_KIRKWOOD dependency
> thermal: Remove ARCH_KIRKWOOD dependency
> leds: Remove ARCH_KIRKWOOD dependency
> rtc: Remove ARCH_KIRKWOOD dependency
> watchdog: Remove ARCH_KIRKWOOD dependency
> cpufreq: Remove ARCH_KIRKWOOD dependency
I have no problems with these changes, but what exactly am I supposed to do?
Rafael
^ permalink raw reply [flat|nested] 29+ messages in thread
* Re: [Patch v3] 0/7] Remove mach-kirkwood
2014-09-01 13:56 ` Rafael J. Wysocki
@ 2014-09-01 14:03 ` Andrew Lunn
-1 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-09-01 14:03 UTC (permalink / raw)
To: Rafael J. Wysocki
Cc: Andrew Lunn, Jason Cooper, linux ARM, Daniel Lezcano, linux-pm,
Tejun Heo, linux-ide, Zhang Rui, Richard Purdie, linux-leds,
Alessandro Zummo, rtc-linux, Wim Van Sebroeck, linux-watchdog,
Viresh Kumar
On Mon, Sep 01, 2014 at 03:56:43PM +0200, Rafael J. Wysocki wrote:
> On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> > This is mostly a resend of these patches, removing mach-kirkwood. Not
> > all maintainers picked up there patches, which has resulted in some
> > dead kernel configuration in v3.17-rcX.
> >
> > The patch set has been rebased on v3.17-rc2, and it is intended that
> > Jason Cooper will submit them for inclusion in an RC. Subsystem
> > maintainers do not need to do anything.
> >
> > The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> > since what it is removing was added during v3.16-rcX. It follows the
> > pattern of all the other patches.
> >
> > Andrew Lunn (7):
> > cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> > ata: Remove ARCH_KIRKWOOD dependency
> > thermal: Remove ARCH_KIRKWOOD dependency
> > leds: Remove ARCH_KIRKWOOD dependency
> > rtc: Remove ARCH_KIRKWOOD dependency
> > watchdog: Remove ARCH_KIRKWOOD dependency
> > cpufreq: Remove ARCH_KIRKWOOD dependency
>
> I have no problems with these changes, but what exactly am I supposed to do?
Jason will submit the whole series. So an Acked-by: would be nice.
Andrew
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 0/7] Remove mach-kirkwood
@ 2014-09-01 14:03 ` Andrew Lunn
0 siblings, 0 replies; 29+ messages in thread
From: Andrew Lunn @ 2014-09-01 14:03 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Sep 01, 2014 at 03:56:43PM +0200, Rafael J. Wysocki wrote:
> On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> > This is mostly a resend of these patches, removing mach-kirkwood. Not
> > all maintainers picked up there patches, which has resulted in some
> > dead kernel configuration in v3.17-rcX.
> >
> > The patch set has been rebased on v3.17-rc2, and it is intended that
> > Jason Cooper will submit them for inclusion in an RC. Subsystem
> > maintainers do not need to do anything.
> >
> > The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> > since what it is removing was added during v3.16-rcX. It follows the
> > pattern of all the other patches.
> >
> > Andrew Lunn (7):
> > cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> > ata: Remove ARCH_KIRKWOOD dependency
> > thermal: Remove ARCH_KIRKWOOD dependency
> > leds: Remove ARCH_KIRKWOOD dependency
> > rtc: Remove ARCH_KIRKWOOD dependency
> > watchdog: Remove ARCH_KIRKWOOD dependency
> > cpufreq: Remove ARCH_KIRKWOOD dependency
>
> I have no problems with these changes, but what exactly am I supposed to do?
Jason will submit the whole series. So an Acked-by: would be nice.
Andrew
^ permalink raw reply [flat|nested] 29+ messages in thread
* Re: [Patch v3] 0/7] Remove mach-kirkwood
2014-09-01 14:03 ` Andrew Lunn
@ 2014-09-01 23:46 ` Rafael J. Wysocki
-1 siblings, 0 replies; 29+ messages in thread
From: Rafael J. Wysocki @ 2014-09-01 23:46 UTC (permalink / raw)
To: Andrew Lunn
Cc: Jason Cooper, linux ARM, Daniel Lezcano, linux-pm, Tejun Heo,
linux-ide, Zhang Rui, Richard Purdie, linux-leds,
Alessandro Zummo, rtc-linux, Wim Van Sebroeck, linux-watchdog,
Viresh Kumar
On Monday, September 01, 2014 04:03:20 PM Andrew Lunn wrote:
> On Mon, Sep 01, 2014 at 03:56:43PM +0200, Rafael J. Wysocki wrote:
> > On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> > > This is mostly a resend of these patches, removing mach-kirkwood. Not
> > > all maintainers picked up there patches, which has resulted in some
> > > dead kernel configuration in v3.17-rcX.
> > >
> > > The patch set has been rebased on v3.17-rc2, and it is intended that
> > > Jason Cooper will submit them for inclusion in an RC. Subsystem
> > > maintainers do not need to do anything.
> > >
> > > The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> > > since what it is removing was added during v3.16-rcX. It follows the
> > > pattern of all the other patches.
> > >
> > > Andrew Lunn (7):
> > > cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> > > ata: Remove ARCH_KIRKWOOD dependency
> > > thermal: Remove ARCH_KIRKWOOD dependency
> > > leds: Remove ARCH_KIRKWOOD dependency
> > > rtc: Remove ARCH_KIRKWOOD dependency
> > > watchdog: Remove ARCH_KIRKWOOD dependency
> > > cpufreq: Remove ARCH_KIRKWOOD dependency
> >
> > I have no problems with these changes, but what exactly am I supposed to do?
>
> Jason will submit the whole series. So an Acked-by: would be nice.
OK, so please regard the cpuidle and cpufreq patches as ACKed.
Rafael
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 0/7] Remove mach-kirkwood
@ 2014-09-01 23:46 ` Rafael J. Wysocki
0 siblings, 0 replies; 29+ messages in thread
From: Rafael J. Wysocki @ 2014-09-01 23:46 UTC (permalink / raw)
To: linux-arm-kernel
On Monday, September 01, 2014 04:03:20 PM Andrew Lunn wrote:
> On Mon, Sep 01, 2014 at 03:56:43PM +0200, Rafael J. Wysocki wrote:
> > On Saturday, August 30, 2014 06:46:05 PM Andrew Lunn wrote:
> > > This is mostly a resend of these patches, removing mach-kirkwood. Not
> > > all maintainers picked up there patches, which has resulted in some
> > > dead kernel configuration in v3.17-rcX.
> > >
> > > The patch set has been rebased on v3.17-rc2, and it is intended that
> > > Jason Cooper will submit them for inclusion in an RC. Subsystem
> > > maintainers do not need to do anything.
> > >
> > > The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> > > since what it is removing was added during v3.16-rcX. It follows the
> > > pattern of all the other patches.
> > >
> > > Andrew Lunn (7):
> > > cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> > > ata: Remove ARCH_KIRKWOOD dependency
> > > thermal: Remove ARCH_KIRKWOOD dependency
> > > leds: Remove ARCH_KIRKWOOD dependency
> > > rtc: Remove ARCH_KIRKWOOD dependency
> > > watchdog: Remove ARCH_KIRKWOOD dependency
> > > cpufreq: Remove ARCH_KIRKWOOD dependency
> >
> > I have no problems with these changes, but what exactly am I supposed to do?
>
> Jason will submit the whole series. So an Acked-by: would be nice.
OK, so please regard the cpuidle and cpufreq patches as ACKed.
Rafael
^ permalink raw reply [flat|nested] 29+ messages in thread
* Re: [Patch v3] 0/7] Remove mach-kirkwood
2014-08-30 16:46 ` Andrew Lunn
@ 2014-09-09 15:10 ` Jason Cooper
-1 siblings, 0 replies; 29+ messages in thread
From: Jason Cooper @ 2014-09-09 15:10 UTC (permalink / raw)
To: Andrew Lunn
Cc: linux ARM, Daniel Lezcano, Rafael J. Wysocki, linux-pm,
Tejun Heo, linux-ide, Zhang Rui, Richard Purdie, linux-leds,
Alessandro Zummo, rtc-linux, Wim Van Sebroeck, linux-watchdog,
Viresh Kumar
Andrew,
On Sat, Aug 30, 2014 at 06:46:05PM +0200, Andrew Lunn wrote:
> This is mostly a resend of these patches, removing mach-kirkwood. Not
> all maintainers picked up there patches, which has resulted in some
> dead kernel configuration in v3.17-rcX.
>
> The patch set has been rebased on v3.17-rc2, and it is intended that
> Jason Cooper will submit them for inclusion in an RC. Subsystem
> maintainers do not need to do anything.
>
> The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> since what it is removing was added during v3.16-rcX. It follows the
> pattern of all the other patches.
>
> Andrew Lunn (7):
> cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> ata: Remove ARCH_KIRKWOOD dependency
> thermal: Remove ARCH_KIRKWOOD dependency
> leds: Remove ARCH_KIRKWOOD dependency
> rtc: Remove ARCH_KIRKWOOD dependency
> watchdog: Remove ARCH_KIRKWOOD dependency
> cpufreq: Remove ARCH_KIRKWOOD dependency
>
> drivers/ata/Kconfig | 2 +-
> drivers/cpufreq/Kconfig.arm | 2 +-
> drivers/cpuidle/Kconfig.arm | 2 +-
> drivers/leds/Kconfig | 4 ++--
> drivers/rtc/Kconfig | 2 +-
> drivers/thermal/Kconfig | 2 +-
> drivers/watchdog/Kconfig | 2 +-
> 7 files changed, 8 insertions(+), 8 deletions(-)
Applied to mvebu/fixes for v3.17 with all the various Acks. Also,
please don't add the extra ']' in the Subject lines, 'git am' threw a
gasket on that so I had to manually edit before applying. Not a big
deal, just an fyi.
thx,
Jason.
^ permalink raw reply [flat|nested] 29+ messages in thread
* [Patch v3] 0/7] Remove mach-kirkwood
@ 2014-09-09 15:10 ` Jason Cooper
0 siblings, 0 replies; 29+ messages in thread
From: Jason Cooper @ 2014-09-09 15:10 UTC (permalink / raw)
To: linux-arm-kernel
Andrew,
On Sat, Aug 30, 2014 at 06:46:05PM +0200, Andrew Lunn wrote:
> This is mostly a resend of these patches, removing mach-kirkwood. Not
> all maintainers picked up there patches, which has resulted in some
> dead kernel configuration in v3.17-rcX.
>
> The patch set has been rebased on v3.17-rc2, and it is intended that
> Jason Cooper will submit them for inclusion in an RC. Subsystem
> maintainers do not need to do anything.
>
> The last patch "cpufreq: Remove ARCH_KIRKWOOD dependency" is new,
> since what it is removing was added during v3.16-rcX. It follows the
> pattern of all the other patches.
>
> Andrew Lunn (7):
> cpuidle: kirkwood: Remove ARCH_KIRKWOOD dependency
> ata: Remove ARCH_KIRKWOOD dependency
> thermal: Remove ARCH_KIRKWOOD dependency
> leds: Remove ARCH_KIRKWOOD dependency
> rtc: Remove ARCH_KIRKWOOD dependency
> watchdog: Remove ARCH_KIRKWOOD dependency
> cpufreq: Remove ARCH_KIRKWOOD dependency
>
> drivers/ata/Kconfig | 2 +-
> drivers/cpufreq/Kconfig.arm | 2 +-
> drivers/cpuidle/Kconfig.arm | 2 +-
> drivers/leds/Kconfig | 4 ++--
> drivers/rtc/Kconfig | 2 +-
> drivers/thermal/Kconfig | 2 +-
> drivers/watchdog/Kconfig | 2 +-
> 7 files changed, 8 insertions(+), 8 deletions(-)
Applied to mvebu/fixes for v3.17 with all the various Acks. Also,
please don't add the extra ']' in the Subject lines, 'git am' threw a
gasket on that so I had to manually edit before applying. Not a big
deal, just an fyi.
thx,
Jason.
^ permalink raw reply [flat|nested] 29+ messages in thread