smartctl 6.0 2012-10-10 r3643 [i686-linux-3.1.10-1.9-desktop] (SUSE RPM) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 RE Device Model: SAMSUNG HE103UJ Serial Number: S13VJDWS900483 LU WWN Device Id: 5 0024e9 002167ef6 Firmware Version: 1AA01118 User Capacity: 1.000.204.886.016 bytes [1,00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7, ATA8-ACS T13/1699-D revision 3b Local Time is: Mon Feb 4 14:04:00 2013 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled AAM feature is: Disabled APM feature is: Disabled Rd look-ahead is: Enabled Write cache is: Enabled ATA Security is: Disabled, NOT FROZEN [SEC1] === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (12124) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 203) minutes. Conveyance self-test routine recommended polling time: ( 22) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 099 099 051 - 531 3 Spin_Up_Time POS--- 073 073 011 - 9000 4 Start_Stop_Count -O--CK 099 099 000 - 1278 5 Reallocated_Sector_Ct PO--CK 100 100 010 - 0 7 Seek_Error_Rate POSR-- 100 100 051 - 0 8 Seek_Time_Performance P-S--K 100 100 015 - 0 9 Power_On_Hours -O--CK 097 097 000 - 16416 10 Spin_Retry_Count PO--CK 100 100 051 - 0 11 Calibration_Retry_Count -O--C- 100 100 000 - 0 12 Power_Cycle_Count -O--CK 099 099 000 - 1277 13 Read_Soft_Error_Rate -OSR-- 099 099 000 - 528 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error PO--CK 100 100 000 - 0 187 Reported_Uncorrect -O--CK 100 100 000 - 1052 188 Command_Timeout -O--CK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 076 059 000 - 24 (Min/Max 12/24) 194 Temperature_Celsius -O---K 077 058 000 - 23 (Min/Max 12/26) 195 Hardware_ECC_Recovered -O-RC- 100 100 000 - 19500704 196 Reallocated_Event_Count -O--CK 100 100 000 - 0 197 Current_Pending_Sector -O--C- 100 100 000 - 0 198 Offline_Uncorrectable ----CK 100 100 000 - 0 199 UDMA_CRC_Error_Count -OSRCK 253 253 000 - 0 200 Multi_Zone_Error_Rate -O-R-- 100 100 000 - 0 201 Soft_Read_Error_Rate -O-R-- 099 099 000 - 12 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 2 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 2 sectors [Ext. Comprehensive SMART error log] GP Log at address 0x04 has 2 sectors [Device Statistics log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 2 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x20 has 2 sectors [Streaming performance log] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (2 sectors) Device Error Count: 6 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 6 [5] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 f2 92 40 00 03:06:50.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 12 40 00 03:06:50.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 92 40 00 03:06:50.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f6 92 40 00 03:06:50.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f7 12 40 00 03:06:50.480 READ FPDMA QUEUED Error 5 [4] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 f7 92 40 00 03:06:48.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f5 92 40 00 03:06:48.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 ef 12 40 00 03:06:48.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fe 12 40 00 03:06:48.480 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fb 12 40 00 03:06:48.480 READ FPDMA QUEUED Error 4 [3] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 f2 92 40 00 03:06:46.470 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 12 40 00 03:06:46.470 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 92 40 00 03:06:46.470 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f6 92 40 00 03:06:46.470 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f7 12 40 00 03:06:46.470 READ FPDMA QUEUED Error 3 [2] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 f7 92 40 00 03:06:44.520 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f5 92 40 00 03:06:44.520 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 ef 12 40 00 03:06:44.520 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fe 12 40 00 03:06:44.520 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fb 12 40 00 03:06:44.520 READ FPDMA QUEUED Error 2 [1] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 f2 92 40 00 03:06:42.530 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 12 40 00 03:06:42.530 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f3 92 40 00 03:06:42.530 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f6 92 40 00 03:06:42.530 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f7 12 40 00 03:06:42.530 READ FPDMA QUEUED Error 1 [0] occurred at disk power-on lifetime: 16413 hours (683 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 00 -- 42 00 00 00 00 0c c2 ef 3e 40 00 at LBA = 0x0cc2ef3e = 214101822 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 00 00 80 00 00 00 c2 fb 92 40 00 03:06:40.150 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fb 12 40 00 03:06:40.150 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fa 92 40 00 03:06:40.150 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 fa 12 40 00 03:06:40.150 READ FPDMA QUEUED 60 00 00 00 80 00 00 00 c2 f9 92 40 00 03:06:40.150 READ FPDMA QUEUED SMART Extended Self-test Log Version: 1 (2 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 2 SCT Version (vendor specific): 256 (0x0100) SCT Support Level: 1 Device State: Active (0) Current Temperature: 23 Celsius Power Cycle Max Temperature: 26 Celsius Lifetime Max Temperature: 63 Celsius SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: -4/72 Celsius Min/Max Temperature Limit: -9/77 Celsius Temperature History Size (Index): 128 (4) Index Estimated Time Temperature Celsius 5 2013-02-04 11:57 24 ***** ... ..( 32 skipped). .. ***** 38 2013-02-04 12:30 24 ***** 39 2013-02-04 12:31 25 ****** 40 2013-02-04 12:32 24 ***** ... ..( 52 skipped). .. ***** 93 2013-02-04 13:25 24 ***** 94 2013-02-04 13:26 23 **** ... ..( 37 skipped). .. **** 4 2013-02-04 14:04 23 **** SCT Error Recovery Control: Read: 70 (7,0 seconds) Write: 70 (7,0 seconds) ATA_READ_LOG_EXT (addr=0x04:0x00, page=0, n=1) failed: scsi error aborted command SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 5 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 5 Transition from drive PhyRdy to drive PhyNRdy 0x000b 2 0 CRC errors within host-to-device FIS 0x000d 2 0 Non-CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0010 2 0 R_ERR response for host-to-device data FIS, non-CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x0013 2 0 R_ERR response for host-to-device non-data FIS, non-CRC