From: Hugues FRUCHET <hugues.fruchet@st.com>
To: "H. Nikolaus Schaller" <hns@goldelico.com>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Sakari Ailus <sakari.ailus@iki.fi>
Cc: Pavel Machek <pavel@ucw.cz>,
Discussions about the Letux Kernel
<letux-kernel@openphoenux.org>,
LKML <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v1 0/6] Add support of OV9655 camera
Date: Mon, 3 Jul 2017 12:03:38 +0000 [thread overview]
Message-ID: <252d42bd-839c-ff60-a258-c736328a3eaf@st.com> (raw)
In-Reply-To: <BF96E22A-7884-413D-9CEA-2C992B22F756@goldelico.com>
Hi Nikolaus,
nothing really strange in trace, I wanted to check the latest S_FMT and
it is well 1280x1024 YUV:
>> [ 425.579498] video2: VIDIOC_S_FMT: type=vid-cap, width=1280,
height=1024, pixelformat=UYVY, field=none, bytesperline=2560,
sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0,
xfer_func=0
You're right that it seems that the ISP is not seeing any data in input.
Have you double checked the polarities of sync signals ? I see
differences in devicetree:
960 ov9655: endpoint {
961 remote-endpoint = <¶llel_ep>;
962 #if 0 // not used by camera driver - define &parellel_ep for isp
963 bus-width = <8>;
964 data-shift = <2>; /* Lines
9:2 are used */
965 hsync-active = <1>; /* Active
high */
966 vsync-active = <1>; /* Active
high */
967 data-active = <1>; /* Active
high */
968 pclk-sample = <1>; /* Rising */
969 #endif
Which has been commented out in flavour of:
1011 /* parallel camera interface */
1012 ¶llel_ep {
1013 remote-endpoint = <&ov9655>;
1014 ti,isp-clock-divisor = <1>;
1015 ti,strobe-mode;
1016 bus-width = <8>;/* Used data lines */
1017 data-shift = <2>; /* Lines 9:2 are used */
1018 hsync-active = <0>; /* Active low */
1019 vsync-active = <1>; /* Active high */
1020 data-active = <1>;/* Active high */
1021 pclk-sample = <1>;/* Rising */
1022 };
there is a difference regarding active level of hsync.
Nevertheless seems OK if I check OMAP3 ISP register:
CCDC SYN_MODE=0x00071704
#define ISPCCDC_SYN_MODE_VDPOL (1 << 2)
#define ISPCCDC_SYN_MODE_HDPOL (1 << 3)
seems well that vertical is 1 and horizontal is 0.
BR,
Hugues.
On 07/03/2017 11:14 AM, H. Nikolaus Schaller wrote:
> Hi Hugues,
>
>> Am 03.07.2017 um 10:16 schrieb Hugues FRUCHET <hugues.fruchet@st.com>:
>>
>> Hi Nikolaus,
>> Could you enable V4L2 UAPI traces ? Something like:
>> echo 0xFF > /sys/devices/platform/soc/<isp address>.<isp
>> name>/video4linux/video2/dev_debug
>>
>> you will see then in kernel dmesg the V4L2 calls and their
>> parameters/return values.
>
> Nice.
>
>> root@letux:~# echo 255 >/sys/devices/platform/68000000.ocp/480bc000.isp/video4linux/video2/dev_debug
>> root@letux:~# ./camera-demo sxga
>> Camera: /dev/v4l-subdev8
>> Setting mode sxga
>> media-ctl -r
>> media-ctl -l '"ov965x":0 -> "OMAP3 ISP CCDC":0[1]'
>> media-ctl -l '"OMAP3 ISP CCDC":1 -> "OMAP3 ISP CCDC output":0[1]'
>> media-ctl -V '"ov965x":0 [UYVY2X8 1280x1024]'
>> media-ctl -V '"OMAP3 ISP CCDC":0 [UYVY2X8 1280x1024]'
>> media-ctl -V '"OMAP3 ISP CCDC":1 [UYVY 1280x1024]'
>> ### starting mplayer in sxga mode ###
>> mplayer tv:// -vf rotate=2 -tv driver=v4l2:device=/dev/video2:outfmt=uyvy:width=1280:height=1024:fps=15 -vo x11
>> MPlayer2 2.0-728-g2c378c7-4+b1 (C) 2000-2012 MPlayer Team
>>
>> Playing tv://.
>> Detected file format: TV
>> Selected driver: v4l2
>> name: Video 4 Linux 2 input
>> author: Martin Olschewski <olschewski@zpr.uni-koeln.de>
>> comment: first try, more to come ;-)
>> [ 425.216094] video2: open (0)
>> [ 425.219329] video2: VIDIOC_QUERYCAP: driver=ispvideo, card=OMAP3 ISP CCDC output, bus=media, version=0x00040c00, capabilities=0x84200003, device_caps=0x04200001
>> [ 425.236389] video2: VIDIOC_G_FMT: type=vid-cap, width=0, height=0, pixelformat=, field=any, bytesperline=0, sizeimage=0, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.254699] video2: VIDIOC_G_STD: error -25: std=0x00000000
>> [ 425.260620] video2: VIDIOC_G_PARM: error -22: type=vid-cap, capability=0x0, capturemode=0x0, timeperframe=0/0, extendedmode=0, readbuffers=0
>> v4l2: ioctl get standard failed: Invalid argumen[ 425.275573] video2: VIDIOC_ENUMSTD: error -25: index=0, id=0x0, name=, fps=0/0, framelines=0
>> t
>> Selected device: OMAP3 ISP CCDC output
>> Capa[ 425.289398] video2: VIDIOC_ENUMINPUT: index=0, name=camera, type=2, audioset=0x0, tuner=0, std=0x00000000, status=0x0, capabilities=0x0
>> bilities: video capture video output streamin[ 425.306396] video2: VIDIOC_ENUMINPUT: error -22: index=1, name=, type=0, audioset=0x0, tuner=0, std=0x00000000, status=0x0, capabilities=0x0
>> g
>> supported norms:
>> inputs: 0 = camera;[ 425.323822] video2: VIDIOC_G_INPUT: value=0
>>
>> Current input: 0
>> [ 425.332580] video2: VIDIOC_ENUM_FMT: error -25: index=0, type=vid-cap, flags=0x0, pixelformat=, description=''
>> Current format: unknown (0x0)
>> [ 425.345428] video2: VIDIOC_G_FMT: type=vid-cap, width=0, height=0, pixelformat=, field=any, bytesperline=0, sizeimage=0, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.367858] video2: VIDIOC_S_FMT: type=vid-cap, width=640, height=480, pixelformat=, field=none, bytesperline=0, sizeimage=0, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.386627] video2: VIDIOC_G_FMT: type=vid-cap, width=640, height=480, pixelformat=, field=none, bytesperline=0, sizeimage=0, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.405334] video2: VIDIOC_S_FMT: type=vid-cap, width=640, height=480, pixelformat=UYVY, field=none, bytesperline=1280, sizeimage=614400, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.425720] video2: VIDIOC_ENUMINPUT: index=0, name=camera, type=2, audioset=0x0, tuner=0, std=0x00000000, status=0x0, capabilities=0x0
>> [ 425.439727] video2: VIDIOC_S_INPUT: value=0
>> [ 425.445159] video2: VIDIOC_ENUMSTD: error -25: index=0, id=0x0, name=, fps=0/0, framelines=0
>> tv.c: norm_from_string(pal): Bogus norm paramete[ 425.455871] video2: VIDIOC_ENUMSTD: error -25: index=0, id=0x0, name=, fps=0/0, framelines=0
>> r, setting default.
>> v4l2: ioctl enum norm failed: In[ 425.470397] video2: VIDIOC_G_FMT: type=vid-cap, width=640, height=480, pixelformat=UYVY, field=none, bytesperline=1280, sizeimage=614400, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> appropriate ioctl for device
>> Error: Cannot set [ 425.493743] video2: VIDIOC_S_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> norm!
>> [ 425.517669] video2: VIDIOC_G_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.538238] video2: VIDIOC_S_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.558990] video2: VIDIOC_G_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.579498] video2: VIDIOC_S_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> Selected input hasn't got a tuner!
>> [ 425.600646] video2: VIDIOC_G_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.623840] video2: VIDIOC_G_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.644317] video2: VIDIOC_G_FMT: type=vid-cap, width=1280, height=1024, pixelformat=UYVY, field=none, bytesperline=2560, sizeimage=2621440, colorspace=0, flags=0x0, ycbcr_enc=0, quantization=0, xfer_func=0
>> [ 425.676971] video2: VIDIOC_REQBUFS: count=2, type=vid-cap, memory=mmap
>> [ 425.684082] video2: VIDIOC_QUERYBUF: 00:00:00.00000000 index=0, type=vid-cap, flags=0x00002000, field=any, sequence=0, memory=mmap, bytesused=0, offset/userptr=0x0, length=2621440
>> [ 425.702117] timecode=00:00:00 type=0, flags=0x00000000, frames=0, userbits=0x00000000
>> [ 425.713073] video2: mmap (0)
>> [ 425.716400] video2: VIDIOC_QBUF: 00:00:00.00000000 index=0, type=vid-cap, flags=0x00002003, field=any, sequence=0, memory=mmap, bytesused=2621440, offset/userptr=0x0, length=2621440
>> [ 425.734436] timecode=00:00:00 type=0, flags=0x00000000, frames=0, userbits=0x00000000
>> [ 425.743499] video2: VIDIOC_QUERYBUF: 00:00:00.00000000 index=1, type=vid-cap, flags=0x00002000, field=any, sequence=0, memory=mmap, bytesused=0, offset/userptr=0x280000, length=2621440
>> [ 425.761688] timecode=00:00:00 type=0, flags=0x00000000, frames=0, userbits=0x00000000
>> [ 425.772186] video2: mmap (0)
>> [ 425.775299] video2: VIDIOC_QBUF: 00:00:00.00000000 index=1, type=vid-cap, flags=0x00002003, field=any, sequence=0, memory=mmap, bytesused=2621440, offset/userptr=0x280000, length=2621440
>> [ 425.793670] timecode=00:00:00 type=0, flags=0x00000000, frames=0, userbits=0x00000000
>> [ 425.802703] video2: VIDIOC_S_CTRL: error -25: id=0x980909, value=0
>> v4l2: ioctl set mute failed: Inappropriate ioctl[ 425.809661] video2: VIDIOC_QUERYCTRL: error -25: id=0x980900, type=0, name=, min/max=0/0, step=0, default=0, flags=0x00000000
>> for device
>> v4l2: ioctl query control failed: Inappropriate [ 425.826965] video2: VIDIOC_QUERYCTRL: error -25: id=0x980903, type=0, name=, min/max=0/0, step=0, default=0, flags=0x00000000
>> ioctl for device
>> v4l2: ioctl query control failed[ 425.844055] video2: VIDIOC_QUERYCTRL: error -25: id=0x980902, type=0, name=, min/max=0/0, step=0, default=0, flags=0x00000000
>> : Inappropriate ioctl for device
>> v4l2: ioctl quer[ 425.860198] video2: VIDIOC_QUERYCTRL: error -25: id=0x980901, type=0, name=, min/max=0/0, step=0, default=0, flags=0x00000000
>> y control failed: Inappropriate ioctl for device
>> v4l2: ioctl query control failed: Inappropriate ioctl for device
>> [ 425.930206] configuring for 1280(2560)x1024
>> [ 425.943481] omap3isp 480bc000.isp: -------------CCDC Register dump-------------
>> [ 425.951171] omap3isp 480bc000.isp: ###CCDC PCR=0x00000000
>> [ 425.958007] omap3isp 480bc000.isp: ###CCDC SYN_MODE=0x00071704
>> [ 425.964996] omap3isp 480bc000.isp: ###CCDC HD_VD_WID=0x00000000
>> [ 425.972656] omap3isp 480bc000.isp: ###CCDC PIX_LINES=0x00000000
>> [ 425.978881] omap3isp 480bc000.isp: ###CCDC HORZ_INFO=0x000004ff
>> [ 425.986114] omap3isp 480bc000.isp: ###CCDC VERT_START=0x00000000
>> [ 425.993255] omap3isp 480bc000.isp: ###CCDC VERT_LINES=0x000003ff
>> [ 425.999694] omap3isp 480bc000.isp: ###CCDC CULLING=0xffff00ff
>> [ 426.006530] omap3isp 480bc000.isp: ###CCDC HSIZE_OFF=0x00000a00
>> [ 426.013580] omap3isp 480bc000.isp: ###CCDC SDOFST=0x00000000
>> [ 426.019531] omap3isp 480bc000.isp: ###CCDC SDR_ADDR=0x40000000
>> [ 426.026550] omap3isp 480bc000.isp: ###CCDC CLAMP=0x00000010
>> [ 426.033142] omap3isp 480bc000.isp: ###CCDC DCSUB=0x00000000
>> [ 426.039123] omap3isp 480bc000.isp: ###CCDC COLPTN=0xbb11bb11
>> [ 426.046020] omap3isp 480bc000.isp: ###CCDC BLKCMP=0x00000000
>> [ 426.052795] omap3isp 480bc000.isp: ###CCDC FPC=0x00000000
>> [ 426.058532] omap3isp 480bc000.isp: ###CCDC FPC_ADDR=0x00000000
>> [ 426.065551] omap3isp 480bc000.isp: ###CCDC VDINT=0x03fe02aa
>> [ 426.072143] omap3isp 480bc000.isp: ###CCDC ALAW=0x00000006
>> [ 426.078033] omap3isp 480bc000.isp: ###CCDC REC656IF=0x00000000
>> [ 426.084960] omap3isp 480bc000.isp: ###CCDC CFG=0x00008800
>> [ 426.090759] omap3isp 480bc000.isp: ###CCDC FMTCFG=0x00000000
>> [ 426.097869] omap3isp 480bc000.isp: ###CCDC FMT_HORZ=0x00000000
>> [ 426.104949] omap3isp 480bc000.isp: ###CCDC FMT_VERT=0x00000000
>> [ 426.111053] omap3isp 480bc000.isp: ###CCDC PRGEVEN0=0x00000000
>> [ 426.118103] omap3isp 480bc000.isp: ###CCDC PRGEVEN1=0x00000000
>> [ 426.124999] omap3isp 480bc000.isp: ###CCDC PRGODD0=0x00000000
>> [ 426.131164] omap3isp 480bc000.isp: ###CCDC PRGODD1=0x00000000
>> [ 426.138000] omap3isp 480bc000.isp: ###CCDC VP_OUT=0x00000000
>> [ 426.144744] omap3isp 480bc000.isp: ###CCDC LSC_CONFIG=0x00006600
>> [ 426.151062] omap3isp 480bc000.isp: ###CCDC LSC_INITIAL=0x00000000
>> [ 426.158325] omap3isp 480bc000.isp: ###CCDC LSC_TABLE_BASE=0x00000000
>> [ 426.165740] omap3isp 480bc000.isp: ###CCDC LSC_TABLE_OFFSET=0x00000000
>> [ 426.173400] omap3isp 480bc000.isp: --------------------------------------------
>> [ 426.188140] video2: VIDIOC_STREAMON: type=vid-cap
>> [ 426.194244] video2: poll: 00000000
>> [ass] auto-open
>> Opening video filter: [rotate=2]
>> VIDEO: 1280x1024 15.000 fps 0.0 kbps ( 0.0 kB/s)
>> Could not find matching colorspace - retrying with -vf scale...
>> Opening video filter: [scale]
>> [swscaler @ 0xb5d45980]using unscaled uyvy422 -> yuv420p special converter
>> VO: [x11] 1024x1280 => 1024x1280 Planar YV12
>> [swscaler @ 0xb5d45980]No accelerated colorspace conversion found from yuv420p to bgra.
>> Colorspace details not fully supported by selected vo.
>> Selected video codec: RAW UYVY [raw]
>> Audio: no sound
>> Starting playback...
>> [ 427.194793] video2: poll: 00000000
>> v4l2: select timeout
>> [ 427.203033] video2: poll: 00000000
>> [ 428.204498] video2: poll: 00000000
>>
>> v4l2: select timeout
>> [ 428.215667] video2: poll: 00000000
>> [ 429.217102] video2: poll: 00000000
>>
>> v4l2: select timeout
>> [ 429.233978] video2: poll: 00000000
>> [ 430.235656] video2: poll: 00000000
>>
>> v4l2: select timeout
>> [ 430.240661] video2: poll: 00000000
>> [ 431.242889] video2: poll: 00000000
>>
>> v4l2: select timeout
>> [ 431.249114] video2: poll: 00000000
>> V: 0.0 6/ 6 ??% ??% ??,?% 0 0
>>
>>
>> MPlayer interrupted by signal 2 in module: filter_video
>> [ 432.251220] video2: poll: 00000000
>> v4l2: select timeout
>> [ 432.256713] video2: poll: 00000000
>> [ 433.258941] video2: poll: 00000000
>>
>> v4l2: select timeout
>> [ 433.266632] omap3isp 480bc000.isp: OMAP3 ISP AEWB: user wants to disable module.
>> [ 433.280090] omap3isp 480bc000.isp: OMAP3 ISP AEWB: module is being disabled
>> [ 433.290130] omap3isp 480bc000.isp: OMAP3 ISP AF: user wants to disable module.
>> [ 433.300140] omap3isp 480bc000.isp: OMAP3 ISP AF: module is being disabled
>> [ 433.309631] omap3isp 480bc000.isp: OMAP3 ISP histogram: user wants to disable module.
>> [ 433.319885] omap3isp 480bc000.isp: OMAP3 ISP histogram: module is being disabled
>> [ 435.373168] omap3isp 480bc000.isp: CCDC stop timeout!
>> [ 435.380371] omap3isp 480bc000.isp: Unable to stop OMAP3 ISP CCDC
>> [ 435.391754] video2: VIDIOC_STREAMOFF: type=vid-cap
>> [ 435.397583] video2: VIDIOC_DQBUF: error -22: 00:00:00.00000000 index=0, type=vid-cap, flags=0x00000000, field=any, sequence=0, memory=mmap, bytesused=0, offset/userptr=0x0, length=0
>> [ 435.417175] timecode=00:00:00 type=0, flags=0x00000000, frames=0, userbits=0x00000000
>> [ 435.431549] video2: VIDIOC_S_CTRL: error -25: id=0x980909, value=1
>> v4l2: ioctl set mute failed: Inappropriate ioctl for device
>> [ 435.495422] video2: release
>> v4l2: 0 frames successfully processed, 1 frames dropped.
>>
>> Exiting... (Quit)
>> root@letux:~#
>
> Seem as if it tells me not much more than setting "pal" norm does fail and there is no "MUTE".
> VIDIOC_STREAMON is successful and the poll times out.
>
> Anyways, this indicates that the problem is probably not in the v4l2 layer but below, i.e. omap3isp+camera.
>
> Maybe as simple as the ISP ignoring the SYNC inputs and then of course failing to capture frames within given time.
> I have checked our pinmux setup but didn't find anything suspicious.
>
> So is it somehow possible to check if the omap3isp is running and receiving sync inpulses?
>
> BR and thanks,
> Nikolaus
>
next prev parent reply other threads:[~2017-07-03 12:03 UTC|newest]
Thread overview: 190+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-22 15:05 [PATCH v1 0/6] Add support of OV9655 camera Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` [PATCH v1 1/6] DT bindings: add bindings for ov965x camera module Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:46 ` Andreas Färber
2017-06-23 10:46 ` Andreas Färber
2017-06-23 10:46 ` Andreas Färber
2017-06-23 10:46 ` Andreas Färber
2017-06-23 10:59 ` H. Nikolaus Schaller
2017-06-23 10:59 ` H. Nikolaus Schaller
2017-06-23 10:59 ` H. Nikolaus Schaller
2017-06-23 10:59 ` H. Nikolaus Schaller
2017-06-23 11:58 ` Laurent Pinchart
2017-06-23 11:58 ` Laurent Pinchart
2017-06-23 11:58 ` Laurent Pinchart
2017-06-23 14:53 ` H. Nikolaus Schaller
2017-06-23 14:53 ` H. Nikolaus Schaller
2017-06-23 14:53 ` H. Nikolaus Schaller
2017-06-23 14:53 ` H. Nikolaus Schaller
2017-06-23 14:57 ` Andreas Färber
2017-06-23 14:57 ` Andreas Färber
2017-06-23 14:57 ` Andreas Färber
2017-06-23 14:57 ` Andreas Färber
2017-06-23 15:22 ` H. Nikolaus Schaller
2017-06-23 15:22 ` H. Nikolaus Schaller
2017-06-23 15:22 ` H. Nikolaus Schaller
2017-06-23 15:22 ` H. Nikolaus Schaller
2017-06-23 18:05 ` Suman Anna
2017-06-23 18:05 ` Suman Anna
2017-06-23 18:05 ` Suman Anna
2017-06-23 18:05 ` Suman Anna
2017-06-23 18:59 ` H. Nikolaus Schaller
2017-06-23 18:59 ` H. Nikolaus Schaller
2017-06-23 18:59 ` H. Nikolaus Schaller
2017-06-23 18:59 ` H. Nikolaus Schaller
2017-06-23 22:24 ` Suman Anna
2017-06-23 22:24 ` Suman Anna
2017-06-23 22:24 ` Suman Anna
2017-06-23 22:24 ` Suman Anna
2017-06-26 6:00 ` H. Nikolaus Schaller
2017-06-26 6:00 ` H. Nikolaus Schaller
2017-06-26 6:00 ` H. Nikolaus Schaller
2017-06-26 6:00 ` H. Nikolaus Schaller
2017-06-26 10:35 ` Hugues FRUCHET
2017-06-26 10:35 ` Hugues FRUCHET
2017-06-26 10:35 ` Hugues FRUCHET
2017-06-26 10:35 ` Hugues FRUCHET
2017-06-26 20:04 ` Sylwester Nawrocki
2017-06-26 20:04 ` Sylwester Nawrocki
2017-06-26 20:04 ` Sylwester Nawrocki
2017-06-26 20:04 ` Sylwester Nawrocki
2017-06-27 5:48 ` H. Nikolaus Schaller
2017-06-27 5:48 ` H. Nikolaus Schaller
2017-06-27 5:48 ` H. Nikolaus Schaller
2017-06-27 22:57 ` Sylwester Nawrocki
2017-06-27 22:57 ` Sylwester Nawrocki
2017-06-27 22:57 ` Sylwester Nawrocki
2017-06-27 22:57 ` Sylwester Nawrocki
2017-06-28 9:12 ` H. Nikolaus Schaller
2017-06-28 9:12 ` H. Nikolaus Schaller
2017-06-28 9:12 ` H. Nikolaus Schaller
2017-06-28 9:12 ` H. Nikolaus Schaller
2017-06-28 10:50 ` Sylwester Nawrocki
2017-06-28 10:50 ` Sylwester Nawrocki
2017-06-28 10:50 ` Sylwester Nawrocki
2017-06-28 10:50 ` Sylwester Nawrocki
2017-06-28 11:24 ` H. Nikolaus Schaller
2017-06-28 11:24 ` H. Nikolaus Schaller
2017-06-28 11:24 ` H. Nikolaus Schaller
2017-06-28 11:24 ` H. Nikolaus Schaller
2017-06-28 12:28 ` Hugues FRUCHET
2017-06-28 12:28 ` Hugues FRUCHET
2017-06-28 12:28 ` Hugues FRUCHET
2017-06-26 18:56 ` Rob Herring
2017-06-26 18:56 ` Rob Herring
2017-06-26 18:56 ` Rob Herring
2017-06-26 18:56 ` Rob Herring
2017-06-26 18:54 ` Rob Herring
2017-06-26 18:54 ` Rob Herring
2017-06-26 18:54 ` Rob Herring
2017-06-22 15:05 ` [PATCH v1 2/6] [media] ov9650: add device tree support Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-26 16:31 ` Sakari Ailus
2017-06-26 16:31 ` Sakari Ailus
2017-06-26 17:46 ` H. Nikolaus Schaller
2017-06-26 17:46 ` H. Nikolaus Schaller
2017-06-26 17:46 ` H. Nikolaus Schaller
2017-06-27 5:36 ` Sakari Ailus
2017-06-27 5:36 ` Sakari Ailus
2017-06-27 5:36 ` Sakari Ailus
2017-06-27 10:14 ` Hugues FRUCHET
2017-06-27 10:14 ` Hugues FRUCHET
2017-06-27 10:14 ` Hugues FRUCHET
2017-06-22 15:05 ` [PATCH v1 3/6] [media] ov9650: select the nearest higher resolution Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` [PATCH v1 4/6] [media] ov9650: use write_array() for resolution sequences Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-26 16:33 ` Sakari Ailus
2017-06-26 16:33 ` Sakari Ailus
2017-06-26 16:33 ` Sakari Ailus
2017-06-29 13:59 ` Hugues FRUCHET
2017-06-29 13:59 ` Hugues FRUCHET
2017-06-29 13:59 ` Hugues FRUCHET
2017-06-29 13:59 ` Hugues FRUCHET
2017-06-22 15:05 ` [PATCH v1 5/6] [media] ov9650: add multiple variant support Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-25 12:36 ` kbuild test robot
2017-06-25 12:36 ` kbuild test robot
2017-06-25 12:36 ` kbuild test robot
2017-06-22 15:05 ` [PATCH v1 6/6] [media] ov9650: add support of OV9655 variant Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-22 15:05 ` Hugues Fruchet
2017-06-25 16:07 ` [PATCH] ov9650: fix semicolon.cocci warnings kbuild test robot
2017-06-25 16:07 ` kbuild test robot
2017-06-25 16:07 ` kbuild test robot
2017-06-25 16:07 ` [PATCH v1 6/6] [media] ov9650: add support of OV9655 variant kbuild test robot
2017-06-25 16:07 ` kbuild test robot
2017-06-25 16:07 ` kbuild test robot
2017-06-26 6:03 ` H. Nikolaus Schaller
2017-06-26 6:03 ` H. Nikolaus Schaller
2017-06-26 6:03 ` H. Nikolaus Schaller
2017-06-26 11:49 ` Hugues FRUCHET
2017-06-26 11:49 ` Hugues FRUCHET
2017-06-26 11:49 ` Hugues FRUCHET
2017-06-26 11:49 ` Hugues FRUCHET
2017-06-22 15:41 ` [PATCH v1 0/6] Add support of OV9655 camera H. Nikolaus Schaller
2017-06-22 15:41 ` H. Nikolaus Schaller
2017-06-22 15:41 ` H. Nikolaus Schaller
2017-06-22 15:41 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-23 10:25 ` H. Nikolaus Schaller
2017-06-25 9:18 ` omap3isp camera was " Pavel Machek
2017-06-25 9:18 ` Pavel Machek
2017-06-25 9:18 ` Pavel Machek
2017-06-26 6:05 ` H. Nikolaus Schaller
2017-06-26 6:05 ` H. Nikolaus Schaller
2017-06-26 6:05 ` H. Nikolaus Schaller
2017-06-26 6:05 ` H. Nikolaus Schaller
2017-06-26 8:39 ` Pavel Machek
2017-06-26 8:39 ` Pavel Machek
2017-06-26 8:39 ` Pavel Machek
2017-06-26 8:39 ` Pavel Machek
2017-06-26 9:53 ` H. Nikolaus Schaller
2017-06-26 9:53 ` H. Nikolaus Schaller
2017-06-26 9:53 ` H. Nikolaus Schaller
2017-06-26 9:53 ` H. Nikolaus Schaller
2017-06-26 11:16 ` Pavel Machek
2017-06-26 11:16 ` Pavel Machek
2017-06-26 11:16 ` Pavel Machek
2017-06-26 11:16 ` Pavel Machek
2017-06-27 5:49 ` H. Nikolaus Schaller
2017-06-27 5:49 ` H. Nikolaus Schaller
2017-06-27 5:49 ` H. Nikolaus Schaller
2017-06-27 5:49 ` H. Nikolaus Schaller
2017-06-26 13:19 ` Hugues FRUCHET
2017-06-26 13:19 ` Hugues FRUCHET
2017-06-26 13:19 ` Hugues FRUCHET
2017-06-26 16:28 ` H. Nikolaus Schaller
2017-06-26 16:28 ` H. Nikolaus Schaller
2017-06-27 7:57 ` Hugues FRUCHET
2017-06-27 7:57 ` Hugues FRUCHET
2017-06-27 7:57 ` Hugues FRUCHET
2017-06-27 7:57 ` Hugues FRUCHET
[not found] ` <95B10899-9966-4844-9667-D2434968A492@goldelico.com>
[not found] ` <85e62c47-e319-c801-376c-95f4d9cbf75a@st.com>
[not found] ` <E183E921-B8F4-4F8A-A302-58297A874990@goldelico.com>
[not found] ` <77bd3b8fe52643d68ecc821ec22bc0e6@SFHDAG5NODE1.st.com>
2017-07-01 21:00 ` H. Nikolaus Schaller
2017-07-03 8:16 ` Hugues FRUCHET
2017-07-03 9:14 ` H. Nikolaus Schaller
2017-07-03 12:03 ` Hugues FRUCHET [this message]
2017-07-03 12:23 ` H. Nikolaus Schaller
2017-07-05 14:02 ` H. Nikolaus Schaller
2017-07-08 20:55 ` Sakari Ailus
2017-06-26 6:02 ` H. Nikolaus Schaller
2017-06-26 6:02 ` H. Nikolaus Schaller
2017-06-26 6:02 ` H. Nikolaus Schaller
2017-06-26 6:02 ` H. Nikolaus Schaller
2017-06-26 10:05 ` Hugues FRUCHET
2017-06-26 10:05 ` Hugues FRUCHET
2017-06-26 10:05 ` Hugues FRUCHET
2017-06-26 10:05 ` Hugues FRUCHET
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=252d42bd-839c-ff60-a258-c736328a3eaf@st.com \
--to=hugues.fruchet@st.com \
--cc=hns@goldelico.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=letux-kernel@openphoenux.org \
--cc=linux-kernel@vger.kernel.org \
--cc=pavel@ucw.cz \
--cc=sakari.ailus@iki.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.