From mboxrd@z Thu Jan 1 00:00:00 1970 From: Stefano Babic Date: Thu, 7 Dec 2017 09:39:23 +0100 Subject: [U-Boot] [PATCH V2 12/23] imx: mx8m: add soc related settings and files In-Reply-To: <20171204043136.17167-13-peng.fan@nxp.com> References: <20171204043136.17167-1-peng.fan@nxp.com> <20171204043136.17167-13-peng.fan@nxp.com> Message-ID: <2c6eea11-7718-49e0-57af-5fde81e99975@denx.de> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi Peng, On 04/12/2017 05:31, Peng Fan wrote: > Add SoC level initialization code > - arch_cpu_init > - mmu table > - detect cpu revision > - reset cpu and wdog settings > - M4 boot > - timer init > - wdog settings > - lowlevel init to save/restore registers > - a few dummy header file to avoid build failure > - ft_system_setup and ft_add_optee_node > - mmc env related > > Signed-off-by: Peng Fan > --- > arch/arm/include/asm/arch-mx8m/crm_regs.h | 10 + > arch/arm/include/asm/arch-mx8m/gpio.h | 12 + > arch/arm/include/asm/arch-mx8m/sys_proto.h | 18 + > arch/arm/mach-imx/Makefile | 1 + > arch/arm/mach-imx/mx8m/Makefile | 3 +- > arch/arm/mach-imx/mx8m/lowlevel_init.S | 63 ++++ > arch/arm/mach-imx/mx8m/soc.c | 539 +++++++++++++++++++++++++++++ > 7 files changed, 645 insertions(+), 1 deletion(-) > create mode 100644 arch/arm/include/asm/arch-mx8m/crm_regs.h > create mode 100644 arch/arm/include/asm/arch-mx8m/gpio.h > create mode 100644 arch/arm/include/asm/arch-mx8m/sys_proto.h > create mode 100644 arch/arm/mach-imx/mx8m/lowlevel_init.S > create mode 100644 arch/arm/mach-imx/mx8m/soc.c > > diff --git a/arch/arm/include/asm/arch-mx8m/crm_regs.h b/arch/arm/include/asm/arch-mx8m/crm_regs.h > new file mode 100644 > index 0000000000..6582318983 > --- /dev/null > +++ b/arch/arm/include/asm/arch-mx8m/crm_regs.h > @@ -0,0 +1,10 @@ > +/* > + * Copyright 2017 NXP > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef _ASM_ARCH_MX8M_CRM_REGS_H > +#define _ASM_ARCH_MX8M_CRM_REGS_H > +/* Dummy header, some imx-common code needs this file */ > +#endif > diff --git a/arch/arm/include/asm/arch-mx8m/gpio.h b/arch/arm/include/asm/arch-mx8m/gpio.h > new file mode 100644 > index 0000000000..b666d37700 > --- /dev/null > +++ b/arch/arm/include/asm/arch-mx8m/gpio.h > @@ -0,0 +1,12 @@ > +/* > + * Copyright 2017 NXP > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __ASM_ARCH_MX8M_GPIO_H > +#define __ASM_ARCH_MX8M_GPIO_H > + > +#include > + > +#endif > diff --git a/arch/arm/include/asm/arch-mx8m/sys_proto.h b/arch/arm/include/asm/arch-mx8m/sys_proto.h > new file mode 100644 > index 0000000000..8bf9ac6697 > --- /dev/null > +++ b/arch/arm/include/asm/arch-mx8m/sys_proto.h > @@ -0,0 +1,18 @@ > +/* > + * Copyright (C) 2017 NXP > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#ifndef __ARCH_MX8M_SYS_PROTO_H > +#define __ARCH_MX8M_SYS_PROTO_H > + > +#include > + > +void set_wdog_reset(struct wdog_regs *wdog); > +void enable_tzc380(void); > +void restore_boot_params(void); > +extern unsigned long rom_pointer[]; > +enum boot_device get_boot_device(void); > +bool is_usb_boot(void); > +#endif > diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile > index c807174363..27c154b8b3 100644 > --- a/arch/arm/mach-imx/Makefile > +++ b/arch/arm/mach-imx/Makefile > @@ -127,4 +127,5 @@ obj-$(CONFIG_MX5) += mx5/ > obj-$(CONFIG_MX6) += mx6/ > obj-$(CONFIG_MX7) += mx7/ > obj-$(CONFIG_ARCH_MX7ULP) += mx7ulp/ > +obj-$(CONFIG_MX8M) += mx8m/ > > diff --git a/arch/arm/mach-imx/mx8m/Makefile b/arch/arm/mach-imx/mx8m/Makefile > index 05f38842f0..b1c5d74aab 100644 > --- a/arch/arm/mach-imx/mx8m/Makefile > +++ b/arch/arm/mach-imx/mx8m/Makefile > @@ -4,4 +4,5 @@ > # SPDX-License-Identifier: GPL-2.0+ > # > > -obj-y += clock.o clock_slice.o > +obj-y += lowlevel_init.o > +obj-y += clock.o clock_slice.o soc.o > diff --git a/arch/arm/mach-imx/mx8m/lowlevel_init.S b/arch/arm/mach-imx/mx8m/lowlevel_init.S > new file mode 100644 > index 0000000000..d388f3ba95 > --- /dev/null > +++ b/arch/arm/mach-imx/mx8m/lowlevel_init.S > @@ -0,0 +1,63 @@ > +/* > + * Copyright 2017 NXP > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include > + > +.align 8 > +.global rom_pointer > +rom_pointer: > + .space 256 > + > +/* > + * Routine: save_boot_params (called after reset from start.S) > + */ > + > +.global save_boot_params > +save_boot_params: save_boot_params is a weak function, but there is a comment for it about that stack is not available at this point, any you are using the stack. And what about this with exception_entry / exception_exit ? Your looks a rewrite of functions in arch/arm/cpu/armv8/exceptions.S > + /* The firmware provided ATAG/FDT address can be found in r2/x0 */ > + adr x0, rom_pointer > + stp x1, x2, [x0], #16 > + stp x3, x4, [x0], #16 > + stp x5, x6, [x0], #16 > + stp x7, x8, [x0], #16 > + stp x9, x10, [x0], #16 > + stp x11, x12, [x0], #16 > + stp x13, x14, [x0], #16 > + stp x15, x16, [x0], #16 > + stp x17, x18, [x0], #16 > + stp x19, x20, [x0], #16 > + stp x21, x22, [x0], #16 > + stp x23, x24, [x0], #16 > + stp x25, x26, [x0], #16 > + stp x27, x28, [x0], #16 > + stp x29, x30, [x0], #16 > + mov x30, sp > + str x30, [x0], #8 > + > + /* Returns */ > + b save_boot_params_ret > + > +.global restore_boot_params > +restore_boot_params: > + adr x0, rom_pointer > + ldp x1, x2, [x0], #16 > + ldp x3, x4, [x0], #16 > + ldp x5, x6, [x0], #16 > + ldp x7, x8, [x0], #16 > + ldp x9, x10, [x0], #16 > + ldp x11, x12, [x0], #16 > + ldp x13, x14, [x0], #16 > + ldp x15, x16, [x0], #16 > + ldp x17, x18, [x0], #16 > + ldp x19, x20, [x0], #16 > + ldp x21, x22, [x0], #16 > + ldp x23, x24, [x0], #16 > + ldp x25, x26, [x0], #16 > + ldp x27, x28, [x0], #16 > + ldp x29, x30, [x0], #16 > + ldr x0, [x0] > + mov sp, x0 > + ret > diff --git a/arch/arm/mach-imx/mx8m/soc.c b/arch/arm/mach-imx/mx8m/soc.c > new file mode 100644 > index 0000000000..740e84caa4 > --- /dev/null > +++ b/arch/arm/mach-imx/mx8m/soc.c > @@ -0,0 +1,539 @@ > +/* > + * Copyright 2017 NXP > + * > + * Peng Fan > + * > + * SPDX-License-Identifier: GPL-2.0+ > + */ > + > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > +#include > + > +DECLARE_GLOBAL_DATA_PTR; > + > +#if defined(CONFIG_SECURE_BOOT) > +struct imx_sec_config_fuse_t const imx_sec_config_fuse = { > + .bank = 1, > + .word = 3, > +}; > +#endif > + > +/* > + * OCOTP_TESTER3[9:8] (see Fusemap Description Table offset 0x440) > + * defines a 2-bit SPEED_GRADING > + */ > +#define OCOTP_TESTER3_SPEED_SHIFT 8 > +#define OCOTP_TESTER3_SPEED_800MHZ 0 > +#define OCOTP_TESTER3_SPEED_1GHZ 1 > +#define OCOTP_TESTER3_SPEED_1300MHZ 2 > +#define OCOTP_TESTER3_SPEED_1500MHZ 3 > + > +u32 get_cpu_speed_grade_hz(void) > +{ > + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; > + struct fuse_bank *bank = &ocotp->bank[1]; > + struct fuse_bank1_regs *fuse = > + (struct fuse_bank1_regs *)bank->fuse_regs; > + u32 val; > + > + val = readl(&fuse->tester3); > + val >>= OCOTP_TESTER3_SPEED_SHIFT; > + val &= 0x3; > + > + switch (val) { > + case OCOTP_TESTER3_SPEED_800MHZ: > + return 800000000; > + case OCOTP_TESTER3_SPEED_1GHZ: > + return 1000000000; > + case OCOTP_TESTER3_SPEED_1300MHZ: > + return 1300000000; > + case OCOTP_TESTER3_SPEED_1500MHZ: > + return 1500000000; > + } > + return 0; > +} > + > +/* > + * OCOTP_TESTER3[7:6] (see Fusemap Description Table offset 0x440) > + * defines a 2-bit SPEED_GRADING > + */ > +#define OCOTP_TESTER3_TEMP_SHIFT 6 > + > +/* CPU Temperature Grades */ > +#define TEMP_COMMERCIAL 0 > +#define TEMP_EXTCOMMERCIAL 1 > +#define TEMP_INDUSTRIAL 2 > +#define TEMP_AUTOMOTIVE 3 > + > +u32 get_cpu_temp_grade(int *minc, int *maxc) > +{ > + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; > + struct fuse_bank *bank = &ocotp->bank[1]; > + struct fuse_bank1_regs *fuse = > + (struct fuse_bank1_regs *)bank->fuse_regs; > + u32 val; > + > + val = readl(&fuse->tester3); > + val >>= OCOTP_TESTER3_TEMP_SHIFT; > + val &= 0x3; > + > + if (minc && maxc) { > + if (val == TEMP_AUTOMOTIVE) { > + *minc = -40; > + *maxc = 125; > + } else if (val == TEMP_INDUSTRIAL) { > + *minc = -40; > + *maxc = 105; > + } else if (val == TEMP_EXTCOMMERCIAL) { > + *minc = -20; > + *maxc = 105; > + } else { > + *minc = 0; > + *maxc = 95; > + } > + } > + return val; > +} Even if they appear cross-architecture: get_cpu_speed_grade_hz() and get_cpu_temp_grade() are very similar to the function in mx6/soc.c and (*sigh*) in mx7/soc.c. This becomes the *third* duplication of the same code. Can we factorize this and put the function in a file under mach-imx, shared between mx6/mx7/mx8m ? The expectation is mac-imx/mxX contains just specific code for that architecture, while common code can flow into mach-imx. > + > +int timer_init(void) > +{ > +#ifdef CONFIG_SPL_BUILD > + struct sctr_regs *sctr = (struct sctr_regs *)SYSCNT_CTRL_BASE_ADDR; > + unsigned long freq = readl(&sctr->cntfid0); > + > + /* Update with accurate clock frequency */ > + asm volatile("msr cntfrq_el0, %0" : : "r" (freq) : "memory"); > + > + clrsetbits_le32(&sctr->cntcr, SC_CNTCR_FREQ0 | SC_CNTCR_FREQ1, > + SC_CNTCR_FREQ0 | SC_CNTCR_ENABLE | SC_CNTCR_HDBG); > +#endif > + > + gd->arch.tbl = 0; > + gd->arch.tbu = 0; > + > + return 0; > +} > > +void enable_tzc380(void) > +{ > + struct iomuxc_gpr_base_regs *gpr = > + (struct iomuxc_gpr_base_regs *)IOMUXC_GPR_BASE_ADDR; > + > + /* Enable TZASC and lock setting */ > + setbits_le32(&gpr->gpr[10], GPR_TZASC_EN); > + setbits_le32(&gpr->gpr[10], GPR_TZASC_EN_LOCK); > +} > + > +void set_wdog_reset(struct wdog_regs *wdog) > +{ > + /* > + * Output WDOG_B signal to reset external pmic or POR_B decided by > + * the board desgin. s/desgin/design/ > Without external reset, the peripherals/DDR/ > + * PMIC are not reset, that may cause system working abnormal. > + * WDZST bit is write-once only bit. Align this bit in kernel, > + * otherwise kernel code will have no chance to set this bit. > + */ > + setbits_le16(&wdog->wcr, WDOG_WDT_MASK | WDOG_WDZST_MASK); > +} > + > +static struct mm_region imx8m_mem_map[] = { > + { > + .virt = 0x0UL, > + .phys = 0x0UL, > + .size = 0x100000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | > + PTE_BLOCK_OUTER_SHARE > + }, { > + .virt = 0x100000UL, > + .phys = 0x100000UL, > + .size = 0x8000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | > + PTE_BLOCK_NON_SHARE | > + PTE_BLOCK_PXN | PTE_BLOCK_UXN > + }, { > + .virt = 0x7C0000UL, > + .phys = 0x7C0000UL, > + .size = 0x80000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | > + PTE_BLOCK_NON_SHARE | > + PTE_BLOCK_PXN | PTE_BLOCK_UXN > + }, { > + .virt = 0x900000UL, > + .phys = 0x900000UL, > + .size = 0x200000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | > + PTE_BLOCK_OUTER_SHARE > + }, { > + .virt = 0xB00000UL, > + .phys = 0xB00000UL, > + .size = 0x3f500000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) | > + PTE_BLOCK_NON_SHARE | > + PTE_BLOCK_PXN | PTE_BLOCK_UXN > + }, { > + .virt = 0x40000000UL, > + .phys = 0x40000000UL, > + .size = 0xC0000000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | > + PTE_BLOCK_OUTER_SHARE > + }, { > + .virt = 0x100000000UL, > + .phys = 0x100000000UL, > + .size = 0x040000000UL, > + .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) | > + PTE_BLOCK_OUTER_SHARE > + }, { > + /* List terminator */ > + 0, > + } > +}; > + If you can, taking into account that currently documentation is scarce or missing, can you add comments to each entry to explain each region ? Thanks ! > +struct mm_region *mem_map = imx8m_mem_map; > + > +u32 get_cpu_rev(void) > +{ > + struct anamix_pll *ana_pll = (struct anamix_pll *)ANA_PLL_BASE_ADDR; This require a small explanation. My point: I would like that registers with the same meaning could have the same name, even if defined in different files according to the i.MX variants. This looks a base address and it is ANATOP_BASE_ADDR for other architectures. Any reason for changing it ? Can we at least try to use the same nomenclature across i.MX processors ? > + u32 reg = readl(&ana_pll->digprog); > + u32 type = (reg >> 16) & 0xff; > + u32 rom_version; > + > + reg &= 0xff; > + > + if (reg == 0x10) { > + /* > + * For B0 chip, the DIGPROG is not updated, still TO1.0. > + * we have to check ROM version further > + */ > + rom_version = readl((void __iomem *)0x800); Has a name this address ? Something like SCU_BASE_ADDR (just copied the name, no idea if it is correct ) ? I prefer to remove magic addresses like 0x800, 0x83c and use define for them. > + if (rom_version != 0x10) { > + rom_version = readl((void __iomem *)0x83c); > + if (rom_version >= 0x20) > + reg = 0x20; > + } > + } > + > + return (type << 12) | reg; > +} > + > +static void imx_set_wdog_powerdown(bool enable) > +{ > + struct wdog_regs *wdog1 = (struct wdog_regs *)WDOG1_BASE_ADDR; > + struct wdog_regs *wdog2 = (struct wdog_regs *)WDOG2_BASE_ADDR; > + struct wdog_regs *wdog3 = (struct wdog_regs *)WDOG3_BASE_ADDR; > + > + /* Write to the PDE (Power Down Enable) bit */ > + writew(enable, &wdog1->wmcr); > + writew(enable, &wdog2->wmcr); > + writew(enable, &wdog3->wmcr); > +} > + > +int arch_cpu_init(void) > +{ > + /* > + * Init timer at very early state, because sscg pll setting > + * will use it > + */ > + timer_init(); > + > + if (IS_ENABLED(CONFIG_SPL_BUILD)) { > + clock_init(); > + imx_set_wdog_powerdown(false); > + } > + > + return 0; > +} > + > +#if defined(CONFIG_FEC_MXC) > +void imx_get_mac_from_fuse(int dev_id, unsigned char *mac) > +{ > + struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; > + struct fuse_bank *bank = &ocotp->bank[9]; > + struct fuse_bank9_regs *fuse = > + (struct fuse_bank9_regs *)bank->fuse_regs; > + u32 value = readl(&fuse->mac_addr1); > + > + mac[0] = (value >> 8); > + mac[1] = value; > + > + value = readl(&fuse->mac_addr0); > + mac[2] = value >> 24; > + mac[3] = value >> 16; > + mac[4] = value >> 8; > + mac[5] = value; > +} This is the last copy of imx_get_mac_from_fuse() that we introduce in U-Boot. At least the 3rd copy, and it is time to factorize them. All functions are doing the same ! > +#endif > + > +#ifdef CONFIG_IMX_BOOTAUX > +int arch_auxiliary_core_up(u32 core_id, ulong boot_private_data) > +{ > + u32 stack, pc; > + > + if (!boot_private_data) > + return -EINVAL; > + > + stack = *(u32 *)boot_private_data; > + pc = *(u32 *)(boot_private_data + 4); > + > + /* Set the stack and pc to M4 bootROM */ > + writel(stack, M4_BOOTROM_BASE_ADDR); > + writel(pc, M4_BOOTROM_BASE_ADDR + 4); > + > + /* Enable M4 */ > + call_imx_sip(IMX_SIP_SRC, IMX_SIP_SRC_M4_START, 0, 0); > + > + return 0; > +} Quite the same, apart sip call, and this can be factorized, too. > + > +int arch_auxiliary_core_check_up(u32 core_id) > +{ > + return call_imx_sip(IMX_SIP_SRC, IMX_SIP_SRC_M4_STARTED, 0, 0); > +} > +#endif > + > +enum boot_device get_boot_device(void) > +{ > + struct bootrom_sw_info **p = > + is_soc_rev(CHIP_REV_1_0) ? > + (struct bootrom_sw_info **)ROM_SW_INFO_ADDR_A0 : > + (struct bootrom_sw_info **)ROM_SW_INFO_ADDR; > + > + enum boot_device boot_dev = SD1_BOOT; > + u8 boot_type = (*p)->boot_dev_type; > + u8 boot_instance = (*p)->boot_dev_instance; > + > + switch (boot_type) { > + case BOOT_TYPE_SD: > + boot_dev = boot_instance + SD1_BOOT; > + break; > + case BOOT_TYPE_MMC: > + boot_dev = boot_instance + MMC1_BOOT; > + break; > + case BOOT_TYPE_NAND: > + boot_dev = NAND_BOOT; > + break; > + case BOOT_TYPE_QSPI: > + boot_dev = QSPI_BOOT; > + break; > + case BOOT_TYPE_WEIM: > + boot_dev = WEIM_NOR_BOOT; > + break; > + case BOOT_TYPE_SPINOR: > + boot_dev = SPI_NOR_BOOT; > + break; > + case BOOT_TYPE_USB: > + boot_dev = USB_BOOT; > + break; > + default: > + break; > + } > + I suggest to add BOOT_TYPE_USB for all i.MXes and factorized this function, too. This is really identical to the one in arch/arm/mach-imx/mx7/soc.c > + return boot_dev; > +} > + > +bool is_usb_boot(void) > +{ > + return get_boot_device() == USB_BOOT; > +} > + > +#ifdef CONFIG_ENV_IS_IN_MMC > +__weak int board_mmc_get_env_dev(int devno) > +{ > + return CONFIG_SYS_MMC_ENV_DEV; > +} > + > +int mmc_get_env_dev(void) > +{ > + struct bootrom_sw_info **p = > + is_soc_rev(CHIP_REV_1_0) ? > + (struct bootrom_sw_info **)ROM_SW_INFO_ADDR_A0 : > + (struct bootrom_sw_info **)ROM_SW_INFO_ADDR; > + int devno = (*p)->boot_dev_instance; > + u8 boot_type = (*p)->boot_dev_type; > + > + /* If not boot from sd/mmc, use default value */ > + if ((boot_type != BOOT_TYPE_SD) && (boot_type != BOOT_TYPE_MMC)) > + return CONFIG_SYS_MMC_ENV_DEV; > + > + return board_mmc_get_env_dev(devno); > +} Quite the same for mmc_get_env_dev() I sumarize: as you explained, there are much more similarities with imx6 / imx7 in MX8M. This means we can share the same code between arch, at least between i.MX7 and i.MX8M (but, ideally, as much as we can). > +#endif > + > +#ifdef CONFIG_OF_SYSTEM_SETUP > +static int ft_add_optee_node(void *fdt, bd_t *bd) > +{ > + const char *path, *subpath; > + int offs; > + > + /* > + * No TEE space allocated indicating no TEE running, so no > + * need to add optee node in dts > + */ > + if (!rom_pointer[1]) > + return 0; > + > + offs = fdt_increase_size(fdt, 512); > + if (offs) { > + printf("No Space for dtb\n"); > + return offs; > + } > + > + path = "/firmware"; > + offs = fdt_path_offset(fdt, path); > + if (offs < 0) { > + path = "/"; > + offs = fdt_path_offset(fdt, path); > + > + if (offs < 0) { > + printf("Could not find root node.\n"); > + return offs; > + } > + > + subpath = "firmware"; > + offs = fdt_add_subnode(fdt, offs, subpath); > + if (offs < 0) { > + printf("Could not create %s node.\n", subpath); > + return offs; > + } > + } > + > + subpath = "optee"; > + offs = fdt_add_subnode(fdt, offs, subpath); > + if (offs < 0) { > + printf("Could not create %s node.\n", subpath); > + return offs; > + } > + > + fdt_setprop_string(fdt, offs, "compatible", "linaro,optee-tz"); > + fdt_setprop_string(fdt, offs, "method", "smc"); > + > + return 0; > +} This has nothing to do with the specific SOC and should be moved. > + > +int ft_system_setup(void *blob, bd_t *bd) > +{ > + static const char * const status = "disabled"; > + static const char * const usb_dwc3_path = "/usb at 38100000/dwc3"; > + static const char * const speed = "high-speed"; > + int i = 0; > + int rc; > + int nodeoff; > + > + if (get_boot_device() == USB_BOOT) { > + static const char * const nodes_path[] = { > + "/dcss at 32e00000", > + "/hdmi at 32c00000", > + "/hdmi_cec at 32c33800", > + "/hdmi_drm at 32c00000", > + "/display-subsystem", > + "/sound-hdmi" > + }; > + This should be moved, too, but why do we increase blob size if boot device is USB ? > + for (i = 0; i < ARRAY_SIZE(nodes_path); i++) { > + nodeoff = fdt_path_offset(blob, nodes_path[i]); > + if (nodeoff < 0) > + continue; /* Not found, skip it */ > + > + printf("Found %s node\n", nodes_path[i]); > + > +add_status: > + rc = fdt_setprop(blob, nodeoff, "status", status, > + strlen(status) + 1); > + if (rc) { > + if (rc == -FDT_ERR_NOSPACE) { > + rc = fdt_increase_size(blob, 512); > + if (!rc) > + goto add_status; > + } > + printf("Unable to update property %s:%s, err=%s\n", > + nodes_path[i], "status", > + fdt_strerror(rc)); > + return rc; > + } > + > + printf("Modify %s:%s disabled\n", > + nodes_path[i], "status"); > + } > + > + nodeoff = fdt_path_offset(blob, usb_dwc3_path); > + if (nodeoff >= 0) { > + printf("Found %s node\n", usb_dwc3_path); > + > +usb_modify_speed: > + > + rc = fdt_setprop(blob, nodeoff, "maximum-speed", > + speed, strlen(speed) + 1); > + if (rc) { > + if (rc == -FDT_ERR_NOSPACE) { > + rc = fdt_increase_size(blob, 512); > + if (!rc) > + goto usb_modify_speed; > + } > + printf("Unable to set property %s:%s, err=%s\n", > + usb_dwc3_path, "maximum-speed", > + fdt_strerror(rc)); > + return rc; > + } > + > + printf("Modify %s:%s = %s\n", > + usb_dwc3_path, "maximum-speed", speed); > + } else { > + printf("Can't found %s node\n", usb_dwc3_path); > + } > + } > + > + /* Disable the CPU idle for A0 chip since the HW does not support it */ > + if (is_soc_rev(CHIP_REV_1_0)) { > + static const char * const nodes_path[] = { > + "/cpus/cpu at 0", > + "/cpus/cpu at 1", > + "/cpus/cpu at 2", > + "/cpus/cpu at 3", > + }; > + > + for (i = 0; i < ARRAY_SIZE(nodes_path); i++) { > + nodeoff = fdt_path_offset(blob, nodes_path[i]); > + if (nodeoff < 0) > + continue; /* Not found, skip it */ > + > + printf("Found %s node\n", nodes_path[i]); > + > + rc = fdt_delprop(blob, nodeoff, "cpu-idle-states"); > + if (rc) { > + printf("Unable to update property %s:%s, err=%s\n", > + nodes_path[i], "status", fdt_strerror(rc)); > + return rc; > + } > + > + printf("Remove %s:%s\n", nodes_path[i], > + "cpu-idle-states"); > + } > + } > + > + return ft_add_optee_node(blob, bd); > +} > +#endif > + > +void reset_cpu(ulong addr) > +{ > + struct watchdog_regs *wdog = (struct watchdog_regs *)WDOG1_BASE_ADDR; > + > + /* Clear WDA to trigger WDOG_B immediately */ > + writew((WCR_WDE | WCR_SRS), &wdog->wcr); > + > + while (1) { > + /* > + * spin for .5 seconds before reset > + */ > + } > +} > Best regards, Stefano Babic -- ===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================