w83627hf-isa-0290

Adapter: ISA adapter

VCore 1: +3.36 V (min = +0.00 V, max = +4.08 V)

VCore 2: +3.31 V (min = +0.00 V, max = +4.08 V)

+3.3V: +3.30 V (min = +2.82 V, max = +3.79 V)

+5V: +5.16 V (min = +0.46 V, max = +0.08 V) ALARM

+12V: +11.73 V (min = +6.69 V, max = +7.30 V) ALARM

-12V: +0.96 V (min = -14.50 V, max = -10.63 V) ALARM

-5V: +1.99 V (min = -5.20 V, max = +1.99 V)

V5SB: +5.64 V (min = +5.16 V, max = +5.00 V) ALARM

VBat: +0.00 V (min = +0.35 V, max = +0.16 V) ALARM

fan1: 0 RPM (min = 5273 RPM, div = 128) ALARM

fan2: 0 RPM (min = 6250 RPM, div = 2) ALARM

fan3: 0 RPM (min = 5672 RPM, div = 2) ALARM

temp1: -30°C (high = +33°C, hyst = +8°C) sensor = thermistor

temp2: -34.0°C (high = +80°C, hyst = +75°C) sensor = thermistor

temp3: -34.0°C (high = +80°C, hyst = +75°C) sensor = thermistor

vid: +0.000 V (VRM Version 8.2)

alarms:

beep_enable:

Sound alarm enabled

As you can see none of my fans are working. I've read the wiki on fan control and divisors, but I don't seem to have any config options. Here is the config I have in etc/sensors.conf for my board. I know that my fans must report data, as windows detects the rpms and I have 4 pins on my fan connectors. I'm also able to detect my temperature and fan speed in BIOS. I'm sure it's a simple config I've missed, but I'm new to lm-sensors so any help would be appreciated.

Thanks,

Todd

chip "w83782d-*" "w83627hf-*"

# Same as above for w83781d except that in5 and in6 are computed differently.

# Rather than an internal inverting op amp, the 82d/83s use standard positive

# inputs and the negative voltages are level shifted by a 3.6V reference.

# The math is convoluted, so we hope that your motherboard

# uses the recommended resistor values.

label in0 "VCore 1"

label in1 "VCore 2"

label in2 "+3.3V"

label in3 "+5V"

label in4 "+12V"

label in5 "-12V"

label in6 "-5V"

label in7 "V5SB"

label in8 "VBat"

# Abit BP6 motherboard has a few differences. VCore1 and VCore2 are the core

# voltages of the two processors. Vtt is memory bus termination resistors

# voltage.

# label in1 "Vtt"

# label in8 "VCore2"

compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)

compute in4 ((28/10)+1)*@ , @/((28/10)+1)

compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14

compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14

compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)

# adjust this if your vid is wrong; see doc/vid