[PATCH v2 01/18] usb: xhci-mtk: remove or operator for setting schedule parameters

[PATCH v2 01/18] usb: xhci-mtk: remove or operator for setting schedule parameters

[Chunfeng Yun]

Side effect may happen if use or operator to set schedule parameters
when the parameters are already set before. Set them directly due to
other bits are reserved.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b45e5bf08997..5891f56c64da 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -643,7 +643,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		 */
 		if (usb_endpoint_xfer_int(&ep->desc)
 			|| usb_endpoint_xfer_isoc(&ep->desc))
-			ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(1));
+			ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(1));
 
 		return 0;
 	}
@@ -730,10 +730,10 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
-		ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(sch_ep->pkts)
 			| EP_BCSCOUNT(sch_ep->cs_count)
 			| EP_BBM(sch_ep->burst_mode));
-		ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		ep_ctx->reserved[1] = cpu_to_le32(EP_BOFFSET(sch_ep->offset)
 			| EP_BREPEAT(sch_ep->repeat));
 
 		xhci_dbg(xhci, " PKTS:%x, CSCOUNT:%x, BM:%x, OFFSET:%x, REPEAT:%x\n",
-- 
2.18.0

[PATCH v2 01/18] usb: xhci-mtk: remove or operator for setting schedule parameters

[Chunfeng Yun]

Side effect may happen if use or operator to set schedule parameters
when the parameters are already set before. Set them directly due to
other bits are reserved.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b45e5bf08997..5891f56c64da 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -643,7 +643,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		 */
 		if (usb_endpoint_xfer_int(&ep->desc)
 			|| usb_endpoint_xfer_isoc(&ep->desc))
-			ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(1));
+			ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(1));
 
 		return 0;
 	}
@@ -730,10 +730,10 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
-		ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(sch_ep->pkts)
 			| EP_BCSCOUNT(sch_ep->cs_count)
 			| EP_BBM(sch_ep->burst_mode));
-		ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		ep_ctx->reserved[1] = cpu_to_le32(EP_BOFFSET(sch_ep->offset)
 			| EP_BREPEAT(sch_ep->repeat));
 
 		xhci_dbg(xhci, " PKTS:%x, CSCOUNT:%x, BM:%x, OFFSET:%x, REPEAT:%x\n",
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 01/18] usb: xhci-mtk: remove or operator for setting schedule parameters

[Chunfeng Yun]

Side effect may happen if use or operator to set schedule parameters
when the parameters are already set before. Set them directly due to
other bits are reserved.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b45e5bf08997..5891f56c64da 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -643,7 +643,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		 */
 		if (usb_endpoint_xfer_int(&ep->desc)
 			|| usb_endpoint_xfer_isoc(&ep->desc))
-			ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(1));
+			ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(1));
 
 		return 0;
 	}
@@ -730,10 +730,10 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
-		ep_ctx->reserved[0] |= cpu_to_le32(EP_BPKTS(sch_ep->pkts)
+		ep_ctx->reserved[0] = cpu_to_le32(EP_BPKTS(sch_ep->pkts)
 			| EP_BCSCOUNT(sch_ep->cs_count)
 			| EP_BBM(sch_ep->burst_mode));
-		ep_ctx->reserved[1] |= cpu_to_le32(EP_BOFFSET(sch_ep->offset)
+		ep_ctx->reserved[1] = cpu_to_le32(EP_BOFFSET(sch_ep->offset)
 			| EP_BREPEAT(sch_ep->repeat));
 
 		xhci_dbg(xhci, " PKTS:%x, CSCOUNT:%x, BM:%x, OFFSET:%x, REPEAT:%x\n",
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 02/18] usb: xhci-mtk: improve bandwidth scheduling with TT

[Chunfeng Yun]

When the USB headset is plug into an external hub, sometimes
can't set config due to not enough bandwidth, so need improve
LS/FS INT/ISOC bandwidth scheduling with TT.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yaqii Wu <yaqii.wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 74 ++++++++++++++++++++++++++-------
 drivers/usb/host/xhci-mtk.h     |  6 ++-
 2 files changed, 64 insertions(+), 16 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 5891f56c64da..8950d1f10a7f 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -378,6 +378,31 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 	sch_ep->allocated = used;
 }
 
+static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
+{
+	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
+	u32 num_esit, tmp;
+	int base;
+	int i, j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = offset + i * sch_ep->esit;
+
+		/*
+		 * Compared with hs bus, no matter what ep type,
+		 * the hub will always delay one uframe to send data
+		 */
+		for (j = 0; j < sch_ep->cs_count; j++) {
+			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
+			if (tmp > FS_PAYLOAD_MAX)
+				return -ERANGE;
+		}
+	}
+
+	return 0;
+}
+
 static int check_sch_tt(struct usb_device *udev,
 	struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
@@ -402,7 +427,7 @@ static int check_sch_tt(struct usb_device *udev,
 			return -ERANGE;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 
 	} else {
@@ -432,7 +457,7 @@ static int check_sch_tt(struct usb_device *udev,
 			cs_count = 7; /* HW limit */
 
 		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 		}
 
@@ -448,24 +473,44 @@ static int check_sch_tt(struct usb_device *udev,
 			sch_ep->num_budget_microframes = sch_ep->esit;
 	}
 
-	return 0;
+	return check_fs_bus_bw(sch_ep, offset);
 }
 
 static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep)
+	struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
+	int bw_updated;
+	int bits;
 	int i, j;
 
 	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	bits = (sch_ep->ep_type == ISOC_OUT_EP) ? sch_ep->cs_count : 1;
+
+	if (used)
+		bw_updated = sch_ep->bw_cost_per_microframe;
+	else
+		bw_updated = -sch_ep->bw_cost_per_microframe;
+
 	for (i = 0; i < num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
-		for (j = 0; j < sch_ep->num_budget_microframes; j++)
-			set_bit(base + j, tt->split_bit_map);
+
+		for (j = 0; j < bits; j++) {
+			if (used)
+				set_bit(base + j, tt->ss_bit_map);
+			else
+				clear_bit(base + j, tt->ss_bit_map);
+		}
+
+		for (j = 0; j < sch_ep->cs_count; j++)
+			tt->fs_bus_bw[base + j] += bw_updated;
 	}
 
-	list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	if (used)
+		list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	else
+		list_del(&sch_ep->tt_endpoint);
 }
 
 static int check_sch_bw(struct usb_device *udev,
@@ -535,7 +580,7 @@ static int check_sch_bw(struct usb_device *udev,
 		if (!tt_offset_ok)
 			return -ERANGE;
 
-		update_sch_tt(udev, sch_ep);
+		update_sch_tt(udev, sch_ep, 1);
 	}
 
 	/* update bus bandwidth info */
@@ -548,15 +593,16 @@ static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated)
+	if (sch_ep->allocated) {
 		update_bus_bw(sch_bw, sch_ep, 0);
+		if (sch_ep->sch_tt)
+			update_sch_tt(udev, sch_ep, 0);
+	}
 
-	list_del(&sch_ep->endpoint);
-
-	if (sch_ep->sch_tt) {
-		list_del(&sch_ep->tt_endpoint);
+	if (sch_ep->sch_tt)
 		drop_tt(udev);
-	}
+
+	list_del(&sch_ep->endpoint);
 	kfree(sch_ep);
 }
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index cbb09dfea62e..f42769c69249 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -20,13 +20,15 @@
 #define XHCI_MTK_MAX_ESIT	64
 
 /**
- * @split_bit_map: used to avoid split microframes overlay
+ * @ss_bit_map: used to avoid start split microframes overlay
+ * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
  * @usb_tt: usb TT related
  * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
-	DECLARE_BITMAP(split_bit_map, XHCI_MTK_MAX_ESIT);
+	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
+	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
 	struct usb_tt *usb_tt;
 	int tt_port;
-- 
2.18.0

[PATCH v2 02/18] usb: xhci-mtk: improve bandwidth scheduling with TT

[Chunfeng Yun]

When the USB headset is plug into an external hub, sometimes
can't set config due to not enough bandwidth, so need improve
LS/FS INT/ISOC bandwidth scheduling with TT.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yaqii Wu <yaqii.wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 74 ++++++++++++++++++++++++++-------
 drivers/usb/host/xhci-mtk.h     |  6 ++-
 2 files changed, 64 insertions(+), 16 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 5891f56c64da..8950d1f10a7f 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -378,6 +378,31 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 	sch_ep->allocated = used;
 }
 
+static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
+{
+	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
+	u32 num_esit, tmp;
+	int base;
+	int i, j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = offset + i * sch_ep->esit;
+
+		/*
+		 * Compared with hs bus, no matter what ep type,
+		 * the hub will always delay one uframe to send data
+		 */
+		for (j = 0; j < sch_ep->cs_count; j++) {
+			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
+			if (tmp > FS_PAYLOAD_MAX)
+				return -ERANGE;
+		}
+	}
+
+	return 0;
+}
+
 static int check_sch_tt(struct usb_device *udev,
 	struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
@@ -402,7 +427,7 @@ static int check_sch_tt(struct usb_device *udev,
 			return -ERANGE;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 
 	} else {
@@ -432,7 +457,7 @@ static int check_sch_tt(struct usb_device *udev,
 			cs_count = 7; /* HW limit */
 
 		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 		}
 
@@ -448,24 +473,44 @@ static int check_sch_tt(struct usb_device *udev,
 			sch_ep->num_budget_microframes = sch_ep->esit;
 	}
 
-	return 0;
+	return check_fs_bus_bw(sch_ep, offset);
 }
 
 static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep)
+	struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
+	int bw_updated;
+	int bits;
 	int i, j;
 
 	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	bits = (sch_ep->ep_type == ISOC_OUT_EP) ? sch_ep->cs_count : 1;
+
+	if (used)
+		bw_updated = sch_ep->bw_cost_per_microframe;
+	else
+		bw_updated = -sch_ep->bw_cost_per_microframe;
+
 	for (i = 0; i < num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
-		for (j = 0; j < sch_ep->num_budget_microframes; j++)
-			set_bit(base + j, tt->split_bit_map);
+
+		for (j = 0; j < bits; j++) {
+			if (used)
+				set_bit(base + j, tt->ss_bit_map);
+			else
+				clear_bit(base + j, tt->ss_bit_map);
+		}
+
+		for (j = 0; j < sch_ep->cs_count; j++)
+			tt->fs_bus_bw[base + j] += bw_updated;
 	}
 
-	list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	if (used)
+		list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	else
+		list_del(&sch_ep->tt_endpoint);
 }
 
 static int check_sch_bw(struct usb_device *udev,
@@ -535,7 +580,7 @@ static int check_sch_bw(struct usb_device *udev,
 		if (!tt_offset_ok)
 			return -ERANGE;
 
-		update_sch_tt(udev, sch_ep);
+		update_sch_tt(udev, sch_ep, 1);
 	}
 
 	/* update bus bandwidth info */
@@ -548,15 +593,16 @@ static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated)
+	if (sch_ep->allocated) {
 		update_bus_bw(sch_bw, sch_ep, 0);
+		if (sch_ep->sch_tt)
+			update_sch_tt(udev, sch_ep, 0);
+	}
 
-	list_del(&sch_ep->endpoint);
-
-	if (sch_ep->sch_tt) {
-		list_del(&sch_ep->tt_endpoint);
+	if (sch_ep->sch_tt)
 		drop_tt(udev);
-	}
+
+	list_del(&sch_ep->endpoint);
 	kfree(sch_ep);
 }
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index cbb09dfea62e..f42769c69249 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -20,13 +20,15 @@
 #define XHCI_MTK_MAX_ESIT	64
 
 /**
- * @split_bit_map: used to avoid split microframes overlay
+ * @ss_bit_map: used to avoid start split microframes overlay
+ * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
  * @usb_tt: usb TT related
  * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
-	DECLARE_BITMAP(split_bit_map, XHCI_MTK_MAX_ESIT);
+	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
+	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
 	struct usb_tt *usb_tt;
 	int tt_port;
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 02/18] usb: xhci-mtk: improve bandwidth scheduling with TT

[Chunfeng Yun]

When the USB headset is plug into an external hub, sometimes
can't set config due to not enough bandwidth, so need improve
LS/FS INT/ISOC bandwidth scheduling with TT.

Fixes: 54f6a8af3722 ("usb: xhci-mtk: skip dropping bandwidth of unchecked endpoints")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Yaqii Wu <yaqii.wu@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 74 ++++++++++++++++++++++++++-------
 drivers/usb/host/xhci-mtk.h     |  6 ++-
 2 files changed, 64 insertions(+), 16 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 5891f56c64da..8950d1f10a7f 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -378,6 +378,31 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 	sch_ep->allocated = used;
 }
 
+static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
+{
+	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
+	u32 num_esit, tmp;
+	int base;
+	int i, j;
+
+	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	for (i = 0; i < num_esit; i++) {
+		base = offset + i * sch_ep->esit;
+
+		/*
+		 * Compared with hs bus, no matter what ep type,
+		 * the hub will always delay one uframe to send data
+		 */
+		for (j = 0; j < sch_ep->cs_count; j++) {
+			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
+			if (tmp > FS_PAYLOAD_MAX)
+				return -ERANGE;
+		}
+	}
+
+	return 0;
+}
+
 static int check_sch_tt(struct usb_device *udev,
 	struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
@@ -402,7 +427,7 @@ static int check_sch_tt(struct usb_device *udev,
 			return -ERANGE;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 
 	} else {
@@ -432,7 +457,7 @@ static int check_sch_tt(struct usb_device *udev,
 			cs_count = 7; /* HW limit */
 
 		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->split_bit_map))
+			if (test_bit(offset + i, tt->ss_bit_map))
 				return -ERANGE;
 		}
 
@@ -448,24 +473,44 @@ static int check_sch_tt(struct usb_device *udev,
 			sch_ep->num_budget_microframes = sch_ep->esit;
 	}
 
-	return 0;
+	return check_fs_bus_bw(sch_ep, offset);
 }
 
 static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep)
+	struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
+	int bw_updated;
+	int bits;
 	int i, j;
 
 	num_esit = XHCI_MTK_MAX_ESIT / sch_ep->esit;
+	bits = (sch_ep->ep_type == ISOC_OUT_EP) ? sch_ep->cs_count : 1;
+
+	if (used)
+		bw_updated = sch_ep->bw_cost_per_microframe;
+	else
+		bw_updated = -sch_ep->bw_cost_per_microframe;
+
 	for (i = 0; i < num_esit; i++) {
 		base = sch_ep->offset + i * sch_ep->esit;
-		for (j = 0; j < sch_ep->num_budget_microframes; j++)
-			set_bit(base + j, tt->split_bit_map);
+
+		for (j = 0; j < bits; j++) {
+			if (used)
+				set_bit(base + j, tt->ss_bit_map);
+			else
+				clear_bit(base + j, tt->ss_bit_map);
+		}
+
+		for (j = 0; j < sch_ep->cs_count; j++)
+			tt->fs_bus_bw[base + j] += bw_updated;
 	}
 
-	list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	if (used)
+		list_add_tail(&sch_ep->tt_endpoint, &tt->ep_list);
+	else
+		list_del(&sch_ep->tt_endpoint);
 }
 
 static int check_sch_bw(struct usb_device *udev,
@@ -535,7 +580,7 @@ static int check_sch_bw(struct usb_device *udev,
 		if (!tt_offset_ok)
 			return -ERANGE;
 
-		update_sch_tt(udev, sch_ep);
+		update_sch_tt(udev, sch_ep, 1);
 	}
 
 	/* update bus bandwidth info */
@@ -548,15 +593,16 @@ static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated)
+	if (sch_ep->allocated) {
 		update_bus_bw(sch_bw, sch_ep, 0);
+		if (sch_ep->sch_tt)
+			update_sch_tt(udev, sch_ep, 0);
+	}
 
-	list_del(&sch_ep->endpoint);
-
-	if (sch_ep->sch_tt) {
-		list_del(&sch_ep->tt_endpoint);
+	if (sch_ep->sch_tt)
 		drop_tt(udev);
-	}
+
+	list_del(&sch_ep->endpoint);
 	kfree(sch_ep);
 }
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index cbb09dfea62e..f42769c69249 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -20,13 +20,15 @@
 #define XHCI_MTK_MAX_ESIT	64
 
 /**
- * @split_bit_map: used to avoid split microframes overlay
+ * @ss_bit_map: used to avoid start split microframes overlay
+ * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
  * @usb_tt: usb TT related
  * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
-	DECLARE_BITMAP(split_bit_map, XHCI_MTK_MAX_ESIT);
+	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
+	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
 	struct usb_tt *usb_tt;
 	int tt_port;
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 03/18] usb: xhci-mtk: get the microframe boundary for ESIT

[Chunfeng Yun]

Tune the boundary for FS/LS ESIT due to CS:
For ISOC out-ep, the controller starts transfer data after
the first SS; for others, the data is already transferred
before the last CS.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: fix typo and use ++/-- suggested by Sergei
---
 drivers/usb/host/xhci-mtk-sch.c | 24 +++++++++++++++++++-----
 1 file changed, 19 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8950d1f10a7f..450fa22b7dc7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -513,22 +513,35 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 boundary = sch_ep->esit;
+
+	if (sch_ep->sch_tt) { /* LS/FS with TT */
+		/* tune for CS */
+		if (sch_ep->ep_type != ISOC_OUT_EP)
+			boundary++;
+		else if (boundary > 1) /* normally esit >= 8 for FS/LS */
+			boundary--;
+	}
+
+	return boundary;
+}
+
 static int check_sch_bw(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
-	u32 esit;
 	u32 min_bw;
 	u32 min_index;
 	u32 worst_bw;
 	u32 bw_boundary;
+	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
 	bool tt_offset_ok = false;
 	int ret;
 
-	esit = sch_ep->esit;
-
 	/*
 	 * Search through all possible schedule microframes.
 	 * and find a microframe where its worst bandwidth is minimum.
@@ -537,7 +550,8 @@ static int check_sch_bw(struct usb_device *udev,
 	min_index = 0;
 	min_cs_count = sch_ep->cs_count;
 	min_num_budget = sch_ep->num_budget_microframes;
-	for (offset = 0; offset < esit; offset++) {
+	esit_boundary = get_esit_boundary(sch_ep);
+	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (is_fs_or_ls(udev->speed)) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
@@ -546,7 +560,7 @@ static int check_sch_bw(struct usb_device *udev,
 				tt_offset_ok = true;
 		}
 
-		if ((offset + sch_ep->num_budget_microframes) > sch_ep->esit)
+		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
 			break;
 
 		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
-- 
2.18.0

[PATCH v2 03/18] usb: xhci-mtk: get the microframe boundary for ESIT

[Chunfeng Yun]

Tune the boundary for FS/LS ESIT due to CS:
For ISOC out-ep, the controller starts transfer data after
the first SS; for others, the data is already transferred
before the last CS.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: fix typo and use ++/-- suggested by Sergei
---
 drivers/usb/host/xhci-mtk-sch.c | 24 +++++++++++++++++++-----
 1 file changed, 19 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8950d1f10a7f..450fa22b7dc7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -513,22 +513,35 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 boundary = sch_ep->esit;
+
+	if (sch_ep->sch_tt) { /* LS/FS with TT */
+		/* tune for CS */
+		if (sch_ep->ep_type != ISOC_OUT_EP)
+			boundary++;
+		else if (boundary > 1) /* normally esit >= 8 for FS/LS */
+			boundary--;
+	}
+
+	return boundary;
+}
+
 static int check_sch_bw(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
-	u32 esit;
 	u32 min_bw;
 	u32 min_index;
 	u32 worst_bw;
 	u32 bw_boundary;
+	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
 	bool tt_offset_ok = false;
 	int ret;
 
-	esit = sch_ep->esit;
-
 	/*
 	 * Search through all possible schedule microframes.
 	 * and find a microframe where its worst bandwidth is minimum.
@@ -537,7 +550,8 @@ static int check_sch_bw(struct usb_device *udev,
 	min_index = 0;
 	min_cs_count = sch_ep->cs_count;
 	min_num_budget = sch_ep->num_budget_microframes;
-	for (offset = 0; offset < esit; offset++) {
+	esit_boundary = get_esit_boundary(sch_ep);
+	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (is_fs_or_ls(udev->speed)) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
@@ -546,7 +560,7 @@ static int check_sch_bw(struct usb_device *udev,
 				tt_offset_ok = true;
 		}
 
-		if ((offset + sch_ep->num_budget_microframes) > sch_ep->esit)
+		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
 			break;
 
 		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 03/18] usb: xhci-mtk: get the microframe boundary for ESIT

[Chunfeng Yun]

Tune the boundary for FS/LS ESIT due to CS:
For ISOC out-ep, the controller starts transfer data after
the first SS; for others, the data is already transferred
before the last CS.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: fix typo and use ++/-- suggested by Sergei
---
 drivers/usb/host/xhci-mtk-sch.c | 24 +++++++++++++++++++-----
 1 file changed, 19 insertions(+), 5 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8950d1f10a7f..450fa22b7dc7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -513,22 +513,35 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
+{
+	u32 boundary = sch_ep->esit;
+
+	if (sch_ep->sch_tt) { /* LS/FS with TT */
+		/* tune for CS */
+		if (sch_ep->ep_type != ISOC_OUT_EP)
+			boundary++;
+		else if (boundary > 1) /* normally esit >= 8 for FS/LS */
+			boundary--;
+	}
+
+	return boundary;
+}
+
 static int check_sch_bw(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
-	u32 esit;
 	u32 min_bw;
 	u32 min_index;
 	u32 worst_bw;
 	u32 bw_boundary;
+	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
 	bool tt_offset_ok = false;
 	int ret;
 
-	esit = sch_ep->esit;
-
 	/*
 	 * Search through all possible schedule microframes.
 	 * and find a microframe where its worst bandwidth is minimum.
@@ -537,7 +550,8 @@ static int check_sch_bw(struct usb_device *udev,
 	min_index = 0;
 	min_cs_count = sch_ep->cs_count;
 	min_num_budget = sch_ep->num_budget_microframes;
-	for (offset = 0; offset < esit; offset++) {
+	esit_boundary = get_esit_boundary(sch_ep);
+	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (is_fs_or_ls(udev->speed)) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
@@ -546,7 +560,7 @@ static int check_sch_bw(struct usb_device *udev,
 				tt_offset_ok = true;
 		}
 
-		if ((offset + sch_ep->num_budget_microframes) > sch_ep->esit)
+		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
 			break;
 
 		worst_bw = get_max_bw(sch_bw, sch_ep, offset);
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 04/18] usb: xhci-mtk: add only one extra CS for FS/LS INTR

[Chunfeng Yun]

In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."

Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 450fa22b7dc7..59ba25ca018d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -408,13 +408,11 @@ static int check_sch_tt(struct usb_device *udev,
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
-	u32 fs_budget_start;
 	u32 start_ss, last_ss;
 	u32 start_cs, last_cs;
 	int i;
 
 	start_ss = offset % 8;
-	fs_budget_start = (start_ss + 1) % 8;
 
 	if (sch_ep->ep_type == ISOC_OUT_EP) {
 		last_ss = start_ss + sch_ep->cs_count - 1;
@@ -450,16 +448,14 @@ static int check_sch_tt(struct usb_device *udev,
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
 		else /*  ep_type : INTR IN / INTR OUT */
-			extra_cs_count = (fs_budget_start == 6) ? 1 : 2;
+			extra_cs_count = 1;
 
 		cs_count += extra_cs_count;
 		if (cs_count > 7)
 			cs_count = 7; /* HW limit */
 
-		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
-		}
+		if (test_bit(offset, tt->ss_bit_map))
+			return -ERANGE;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
-- 
2.18.0

[PATCH v2 04/18] usb: xhci-mtk: add only one extra CS for FS/LS INTR

[Chunfeng Yun]

In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."

Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 450fa22b7dc7..59ba25ca018d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -408,13 +408,11 @@ static int check_sch_tt(struct usb_device *udev,
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
-	u32 fs_budget_start;
 	u32 start_ss, last_ss;
 	u32 start_cs, last_cs;
 	int i;
 
 	start_ss = offset % 8;
-	fs_budget_start = (start_ss + 1) % 8;
 
 	if (sch_ep->ep_type == ISOC_OUT_EP) {
 		last_ss = start_ss + sch_ep->cs_count - 1;
@@ -450,16 +448,14 @@ static int check_sch_tt(struct usb_device *udev,
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
 		else /*  ep_type : INTR IN / INTR OUT */
-			extra_cs_count = (fs_budget_start == 6) ? 1 : 2;
+			extra_cs_count = 1;
 
 		cs_count += extra_cs_count;
 		if (cs_count > 7)
 			cs_count = 7; /* HW limit */
 
-		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
-		}
+		if (test_bit(offset, tt->ss_bit_map))
+			return -ERANGE;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 04/18] usb: xhci-mtk: add only one extra CS for FS/LS INTR

[Chunfeng Yun]

In USB2 Spec:
"11.18.5 TT Response Generation
In general, there will be two (or more) complete-split
transactions scheduled for a periodic endpoint.
However, for interrupt endpoints, the maximum size of
the full-/low-speed transaction guarantees that it can
never require more than two complete-split transactions.
Two complete-split transactions are only required
when the transaction spans a microframe boundary."

Due to the maxp is 64, and less then 188 (at most in one
microframe), seems never span boundary, so use only one CS
for FS/LS interrupt transfer, this will save some bandwidth.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 450fa22b7dc7..59ba25ca018d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -408,13 +408,11 @@ static int check_sch_tt(struct usb_device *udev,
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
-	u32 fs_budget_start;
 	u32 start_ss, last_ss;
 	u32 start_cs, last_cs;
 	int i;
 
 	start_ss = offset % 8;
-	fs_budget_start = (start_ss + 1) % 8;
 
 	if (sch_ep->ep_type == ISOC_OUT_EP) {
 		last_ss = start_ss + sch_ep->cs_count - 1;
@@ -450,16 +448,14 @@ static int check_sch_tt(struct usb_device *udev,
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
 		else /*  ep_type : INTR IN / INTR OUT */
-			extra_cs_count = (fs_budget_start == 6) ? 1 : 2;
+			extra_cs_count = 1;
 
 		cs_count += extra_cs_count;
 		if (cs_count > 7)
 			cs_count = 7; /* HW limit */
 
-		for (i = 0; i < cs_count + 2; i++) {
-			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
-		}
+		if (test_bit(offset, tt->ss_bit_map))
+			return -ERANGE;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 05/18] usb: xhci-mtk: use @sch_tt to check whether need do TT schedule

[Chunfeng Yun]

It's clearer to use @sch_tt to check whether need do TT schedule,
no function is changed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 59ba25ca018d..b1da3cb077c9 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -548,7 +548,7 @@ static int check_sch_bw(struct usb_device *udev,
 	min_num_budget = sch_ep->num_budget_microframes;
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
-		if (is_fs_or_ls(udev->speed)) {
+		if (sch_ep->sch_tt) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
@@ -585,7 +585,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (is_fs_or_ls(udev->speed)) {
+	if (sch_ep->sch_tt) {
 		/* all offset for tt is not ok*/
 		if (!tt_offset_ok)
 			return -ERANGE;
-- 
2.18.0

[PATCH v2 05/18] usb: xhci-mtk: use @sch_tt to check whether need do TT schedule

[Chunfeng Yun]

It's clearer to use @sch_tt to check whether need do TT schedule,
no function is changed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 59ba25ca018d..b1da3cb077c9 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -548,7 +548,7 @@ static int check_sch_bw(struct usb_device *udev,
 	min_num_budget = sch_ep->num_budget_microframes;
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
-		if (is_fs_or_ls(udev->speed)) {
+		if (sch_ep->sch_tt) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
@@ -585,7 +585,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (is_fs_or_ls(udev->speed)) {
+	if (sch_ep->sch_tt) {
 		/* all offset for tt is not ok*/
 		if (!tt_offset_ok)
 			return -ERANGE;
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 05/18] usb: xhci-mtk: use @sch_tt to check whether need do TT schedule

[Chunfeng Yun]

It's clearer to use @sch_tt to check whether need do TT schedule,
no function is changed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 59ba25ca018d..b1da3cb077c9 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -548,7 +548,7 @@ static int check_sch_bw(struct usb_device *udev,
 	min_num_budget = sch_ep->num_budget_microframes;
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
-		if (is_fs_or_ls(udev->speed)) {
+		if (sch_ep->sch_tt) {
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
@@ -585,7 +585,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (is_fs_or_ls(udev->speed)) {
+	if (sch_ep->sch_tt) {
 		/* all offset for tt is not ok*/
 		if (!tt_offset_ok)
 			return -ERANGE;
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 06/18] usb: xhci-mtk: add a function to (un)load bandwidth info

[Chunfeng Yun]

Extract a function to load/unload bandwidth info, and remove
a dummy check of TT offset.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++-------------------
 1 file changed, 16 insertions(+), 21 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b1da3cb077c9..9a9685f74940 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -375,7 +375,6 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 					sch_ep->bw_budget_table[j];
 		}
 	}
-	sch_ep->allocated = used;
 }
 
 static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
@@ -509,6 +508,19 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
+{
+	if (sch_ep->sch_tt)
+		update_sch_tt(udev, sch_ep, loaded);
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, loaded);
+	sch_ep->allocated = loaded;
+
+	return 0;
+}
+
 static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 boundary = sch_ep->esit;
@@ -535,7 +547,6 @@ static int check_sch_bw(struct usb_device *udev,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	bool tt_offset_ok = false;
 	int ret;
 
 	/*
@@ -552,8 +563,6 @@ static int check_sch_bw(struct usb_device *udev,
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
-			else
-				tt_offset_ok = true;
 		}
 
 		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
@@ -585,29 +594,15 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (sch_ep->sch_tt) {
-		/* all offset for tt is not ok*/
-		if (!tt_offset_ok)
-			return -ERANGE;
-
-		update_sch_tt(udev, sch_ep, 1);
-	}
-
-	/* update bus bandwidth info */
-	update_bus_bw(sch_bw, sch_ep, 1);
-
-	return 0;
+	return load_ep_bw(udev, sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated) {
-		update_bus_bw(sch_bw, sch_ep, 0);
-		if (sch_ep->sch_tt)
-			update_sch_tt(udev, sch_ep, 0);
-	}
+	if (sch_ep->allocated)
+		load_ep_bw(udev, sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
-- 
2.18.0

[PATCH v2 06/18] usb: xhci-mtk: add a function to (un)load bandwidth info

[Chunfeng Yun]

Extract a function to load/unload bandwidth info, and remove
a dummy check of TT offset.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++-------------------
 1 file changed, 16 insertions(+), 21 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b1da3cb077c9..9a9685f74940 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -375,7 +375,6 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 					sch_ep->bw_budget_table[j];
 		}
 	}
-	sch_ep->allocated = used;
 }
 
 static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
@@ -509,6 +508,19 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
+{
+	if (sch_ep->sch_tt)
+		update_sch_tt(udev, sch_ep, loaded);
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, loaded);
+	sch_ep->allocated = loaded;
+
+	return 0;
+}
+
 static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 boundary = sch_ep->esit;
@@ -535,7 +547,6 @@ static int check_sch_bw(struct usb_device *udev,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	bool tt_offset_ok = false;
 	int ret;
 
 	/*
@@ -552,8 +563,6 @@ static int check_sch_bw(struct usb_device *udev,
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
-			else
-				tt_offset_ok = true;
 		}
 
 		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
@@ -585,29 +594,15 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (sch_ep->sch_tt) {
-		/* all offset for tt is not ok*/
-		if (!tt_offset_ok)
-			return -ERANGE;
-
-		update_sch_tt(udev, sch_ep, 1);
-	}
-
-	/* update bus bandwidth info */
-	update_bus_bw(sch_bw, sch_ep, 1);
-
-	return 0;
+	return load_ep_bw(udev, sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated) {
-		update_bus_bw(sch_bw, sch_ep, 0);
-		if (sch_ep->sch_tt)
-			update_sch_tt(udev, sch_ep, 0);
-	}
+	if (sch_ep->allocated)
+		load_ep_bw(udev, sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 06/18] usb: xhci-mtk: add a function to (un)load bandwidth info

[Chunfeng Yun]

Extract a function to load/unload bandwidth info, and remove
a dummy check of TT offset.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++-------------------
 1 file changed, 16 insertions(+), 21 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index b1da3cb077c9..9a9685f74940 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -375,7 +375,6 @@ static void update_bus_bw(struct mu3h_sch_bw_info *sch_bw,
 					sch_ep->bw_budget_table[j];
 		}
 	}
-	sch_ep->allocated = used;
 }
 
 static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
@@ -509,6 +508,19 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
+static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
+{
+	if (sch_ep->sch_tt)
+		update_sch_tt(udev, sch_ep, loaded);
+
+	/* update bus bandwidth info */
+	update_bus_bw(sch_bw, sch_ep, loaded);
+	sch_ep->allocated = loaded;
+
+	return 0;
+}
+
 static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 boundary = sch_ep->esit;
@@ -535,7 +547,6 @@ static int check_sch_bw(struct usb_device *udev,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	bool tt_offset_ok = false;
 	int ret;
 
 	/*
@@ -552,8 +563,6 @@ static int check_sch_bw(struct usb_device *udev,
 			ret = check_sch_tt(udev, sch_ep, offset);
 			if (ret)
 				continue;
-			else
-				tt_offset_ok = true;
 		}
 
 		if ((offset + sch_ep->num_budget_microframes) > esit_boundary)
@@ -585,29 +594,15 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	if (sch_ep->sch_tt) {
-		/* all offset for tt is not ok*/
-		if (!tt_offset_ok)
-			return -ERANGE;
-
-		update_sch_tt(udev, sch_ep, 1);
-	}
-
-	/* update bus bandwidth info */
-	update_bus_bw(sch_bw, sch_ep, 1);
-
-	return 0;
+	return load_ep_bw(udev, sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
 	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
 {
 	/* only release ep bw check passed by check_sch_bw() */
-	if (sch_ep->allocated) {
-		update_bus_bw(sch_bw, sch_ep, 0);
-		if (sch_ep->sch_tt)
-			update_sch_tt(udev, sch_ep, 0);
-	}
+	if (sch_ep->allocated)
+		load_ep_bw(udev, sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 07/18] usb: xhci-mtk: add a function to get bandwidth boundary

[Chunfeng Yun]

This is used to simplify unit test.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 27 ++++++++++++++++++++-------
 1 file changed, 20 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9a9685f74940..8fe4481eb43d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -37,6 +37,25 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static u32 get_bw_boundary(enum usb_device_speed speed)
+{
+	u32 boundary;
+
+	switch (speed) {
+	case USB_SPEED_SUPER_PLUS:
+		boundary = SSP_BW_BOUNDARY;
+		break;
+	case USB_SPEED_SUPER:
+		boundary = SS_BW_BOUNDARY;
+		break;
+	default:
+		boundary = HS_BW_BOUNDARY;
+		break;
+	}
+
+	return boundary;
+}
+
 /*
 * get the index of bandwidth domains array which @ep belongs to.
 *
@@ -579,13 +598,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	if (udev->speed == USB_SPEED_SUPER_PLUS)
-		bw_boundary = SSP_BW_BOUNDARY;
-	else if (udev->speed == USB_SPEED_SUPER)
-		bw_boundary = SS_BW_BOUNDARY;
-	else
-		bw_boundary = HS_BW_BOUNDARY;
-
+	bw_boundary = get_bw_boundary(udev->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
-- 
2.18.0

[PATCH v2 07/18] usb: xhci-mtk: add a function to get bandwidth boundary

[Chunfeng Yun]

This is used to simplify unit test.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 27 ++++++++++++++++++++-------
 1 file changed, 20 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9a9685f74940..8fe4481eb43d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -37,6 +37,25 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static u32 get_bw_boundary(enum usb_device_speed speed)
+{
+	u32 boundary;
+
+	switch (speed) {
+	case USB_SPEED_SUPER_PLUS:
+		boundary = SSP_BW_BOUNDARY;
+		break;
+	case USB_SPEED_SUPER:
+		boundary = SS_BW_BOUNDARY;
+		break;
+	default:
+		boundary = HS_BW_BOUNDARY;
+		break;
+	}
+
+	return boundary;
+}
+
 /*
 * get the index of bandwidth domains array which @ep belongs to.
 *
@@ -579,13 +598,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	if (udev->speed == USB_SPEED_SUPER_PLUS)
-		bw_boundary = SSP_BW_BOUNDARY;
-	else if (udev->speed == USB_SPEED_SUPER)
-		bw_boundary = SS_BW_BOUNDARY;
-	else
-		bw_boundary = HS_BW_BOUNDARY;
-
+	bw_boundary = get_bw_boundary(udev->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 07/18] usb: xhci-mtk: add a function to get bandwidth boundary

[Chunfeng Yun]

This is used to simplify unit test.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 27 ++++++++++++++++++++-------
 1 file changed, 20 insertions(+), 7 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9a9685f74940..8fe4481eb43d 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -37,6 +37,25 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static u32 get_bw_boundary(enum usb_device_speed speed)
+{
+	u32 boundary;
+
+	switch (speed) {
+	case USB_SPEED_SUPER_PLUS:
+		boundary = SSP_BW_BOUNDARY;
+		break;
+	case USB_SPEED_SUPER:
+		boundary = SS_BW_BOUNDARY;
+		break;
+	default:
+		boundary = HS_BW_BOUNDARY;
+		break;
+	}
+
+	return boundary;
+}
+
 /*
 * get the index of bandwidth domains array which @ep belongs to.
 *
@@ -579,13 +598,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	if (udev->speed == USB_SPEED_SUPER_PLUS)
-		bw_boundary = SSP_BW_BOUNDARY;
-	else if (udev->speed == USB_SPEED_SUPER)
-		bw_boundary = SS_BW_BOUNDARY;
-	else
-		bw_boundary = HS_BW_BOUNDARY;
-
+	bw_boundary = get_bw_boundary(udev->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 08/18] usb: xhci-mtk: remove unnecessary members of mu3h_sch_tt struct

[Chunfeng Yun]

The members @usb_tt and @tt_port in mu3h_sch_tt struct
are not used after initialization, so can be removed

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 7 +------
 drivers/usb/host/xhci-mtk.h     | 4 ----
 2 files changed, 1 insertion(+), 10 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8fe4481eb43d..6fb7a040c73c 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -104,7 +104,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 {
 	struct usb_tt *utt = udev->tt;
 	struct mu3h_sch_tt *tt, **tt_index, **ptt;
-	unsigned int port;
 	bool allocated_index = false;
 
 	if (!utt)
@@ -126,10 +125,8 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			utt->hcpriv = tt_index;
 			allocated_index = true;
 		}
-		port = udev->ttport - 1;
-		ptt = &tt_index[port];
+		ptt = &tt_index[udev->ttport - 1];
 	} else {
-		port = 0;
 		ptt = (struct mu3h_sch_tt **) &utt->hcpriv;
 	}
 
@@ -144,8 +141,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			return ERR_PTR(-ENOMEM);
 		}
 		INIT_LIST_HEAD(&tt->ep_list);
-		tt->usb_tt = utt;
-		tt->tt_port = port;
 		*ptt = tt;
 	}
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f42769c69249..f61e53b02706 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -23,15 +23,11 @@
  * @ss_bit_map: used to avoid start split microframes overlay
  * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
- * @usb_tt: usb TT related
- * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
 	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
 	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
-	struct usb_tt *usb_tt;
-	int tt_port;
 };
 
 /**
-- 
2.18.0

[PATCH v2 08/18] usb: xhci-mtk: remove unnecessary members of mu3h_sch_tt struct

[Chunfeng Yun]

The members @usb_tt and @tt_port in mu3h_sch_tt struct
are not used after initialization, so can be removed

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 7 +------
 drivers/usb/host/xhci-mtk.h     | 4 ----
 2 files changed, 1 insertion(+), 10 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8fe4481eb43d..6fb7a040c73c 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -104,7 +104,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 {
 	struct usb_tt *utt = udev->tt;
 	struct mu3h_sch_tt *tt, **tt_index, **ptt;
-	unsigned int port;
 	bool allocated_index = false;
 
 	if (!utt)
@@ -126,10 +125,8 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			utt->hcpriv = tt_index;
 			allocated_index = true;
 		}
-		port = udev->ttport - 1;
-		ptt = &tt_index[port];
+		ptt = &tt_index[udev->ttport - 1];
 	} else {
-		port = 0;
 		ptt = (struct mu3h_sch_tt **) &utt->hcpriv;
 	}
 
@@ -144,8 +141,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			return ERR_PTR(-ENOMEM);
 		}
 		INIT_LIST_HEAD(&tt->ep_list);
-		tt->usb_tt = utt;
-		tt->tt_port = port;
 		*ptt = tt;
 	}
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f42769c69249..f61e53b02706 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -23,15 +23,11 @@
  * @ss_bit_map: used to avoid start split microframes overlay
  * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
- * @usb_tt: usb TT related
- * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
 	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
 	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
-	struct usb_tt *usb_tt;
-	int tt_port;
 };
 
 /**
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 08/18] usb: xhci-mtk: remove unnecessary members of mu3h_sch_tt struct

[Chunfeng Yun]

The members @usb_tt and @tt_port in mu3h_sch_tt struct
are not used after initialization, so can be removed

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 7 +------
 drivers/usb/host/xhci-mtk.h     | 4 ----
 2 files changed, 1 insertion(+), 10 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 8fe4481eb43d..6fb7a040c73c 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -104,7 +104,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 {
 	struct usb_tt *utt = udev->tt;
 	struct mu3h_sch_tt *tt, **tt_index, **ptt;
-	unsigned int port;
 	bool allocated_index = false;
 
 	if (!utt)
@@ -126,10 +125,8 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			utt->hcpriv = tt_index;
 			allocated_index = true;
 		}
-		port = udev->ttport - 1;
-		ptt = &tt_index[port];
+		ptt = &tt_index[udev->ttport - 1];
 	} else {
-		port = 0;
 		ptt = (struct mu3h_sch_tt **) &utt->hcpriv;
 	}
 
@@ -144,8 +141,6 @@ static struct mu3h_sch_tt *find_tt(struct usb_device *udev)
 			return ERR_PTR(-ENOMEM);
 		}
 		INIT_LIST_HEAD(&tt->ep_list);
-		tt->usb_tt = utt;
-		tt->tt_port = port;
 		*ptt = tt;
 	}
 
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f42769c69249..f61e53b02706 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -23,15 +23,11 @@
  * @ss_bit_map: used to avoid start split microframes overlay
  * @fs_bus_bw: array to keep track of bandwidth already used for FS
  * @ep_list: Endpoints using this TT
- * @usb_tt: usb TT related
- * @tt_port: TT port number
  */
 struct mu3h_sch_tt {
 	DECLARE_BITMAP(ss_bit_map, XHCI_MTK_MAX_ESIT);
 	u32 fs_bus_bw[XHCI_MTK_MAX_ESIT];
 	struct list_head ep_list;
-	struct usb_tt *usb_tt;
-	int tt_port;
 };
 
 /**
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 09/18] usb: xhci-mtk: use clear type instead of void

[Chunfeng Yun]

Use struct usb_host_endpoint instead of void to declare
the member @ep of mu3h_sch_ep_info struct.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f61e53b02706..076b9bbc89dd 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -84,7 +84,7 @@ struct mu3h_sch_ep_info {
 	struct mu3h_sch_tt *sch_tt;
 	u32 ep_type;
 	u32 maxpkt;
-	void *ep;
+	struct usb_host_endpoint *ep;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0

[PATCH v2 09/18] usb: xhci-mtk: use clear type instead of void

[Chunfeng Yun]

Use struct usb_host_endpoint instead of void to declare
the member @ep of mu3h_sch_ep_info struct.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f61e53b02706..076b9bbc89dd 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -84,7 +84,7 @@ struct mu3h_sch_ep_info {
 	struct mu3h_sch_tt *sch_tt;
 	u32 ep_type;
 	u32 maxpkt;
-	void *ep;
+	struct usb_host_endpoint *ep;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 09/18] usb: xhci-mtk: use clear type instead of void

[Chunfeng Yun]

Use struct usb_host_endpoint instead of void to declare
the member @ep of mu3h_sch_ep_info struct.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.h | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index f61e53b02706..076b9bbc89dd 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -84,7 +84,7 @@ struct mu3h_sch_ep_info {
 	struct mu3h_sch_tt *sch_tt;
 	u32 ep_type;
 	u32 maxpkt;
-	void *ep;
+	struct usb_host_endpoint *ep;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 10/18] usb: xhci-mtk: add a member @speed in mu3h_sch_ep_info struct

[Chunfeng Yun]

This is used to drop parameter @udev for some functions,
meanwhile remove some unused @udev parameter.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++-----------------
 drivers/usb/host/xhci-mtk.h     |  1 +
 2 files changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 6fb7a040c73c..3dc727b820aa 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -214,14 +214,15 @@ static struct mu3h_sch_ep_info *create_sch_ep(struct usb_device *udev,
 
 	sch_ep->sch_tt = tt;
 	sch_ep->ep = ep;
+	sch_ep->speed = udev->speed;
 	INIT_LIST_HEAD(&sch_ep->endpoint);
 	INIT_LIST_HEAD(&sch_ep->tt_endpoint);
 
 	return sch_ep;
 }
 
-static void setup_sch_info(struct usb_device *udev,
-		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+static void setup_sch_info(struct xhci_ep_ctx *ep_ctx,
+			   struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 ep_type;
 	u32 maxpkt;
@@ -248,7 +249,7 @@ static void setup_sch_info(struct usb_device *udev,
 	sch_ep->burst_mode = 0;
 	sch_ep->repeat = 0;
 
-	if (udev->speed == USB_SPEED_HIGH) {
+	if (sch_ep->speed == USB_SPEED_HIGH) {
 		sch_ep->cs_count = 0;
 
 		/*
@@ -266,7 +267,7 @@ static void setup_sch_info(struct usb_device *udev,
 		sch_ep->pkts = max_burst + 1;
 		sch_ep->bw_cost_per_microframe = maxpkt * sch_ep->pkts;
 		bwb_table[0] = sch_ep->bw_cost_per_microframe;
-	} else if (udev->speed >= USB_SPEED_SUPER) {
+	} else if (sch_ep->speed >= USB_SPEED_SUPER) {
 		/* usb3_r1 spec section4.4.7 & 4.4.8 */
 		sch_ep->cs_count = 0;
 		sch_ep->burst_mode = 1;
@@ -311,7 +312,7 @@ static void setup_sch_info(struct usb_device *udev,
 			/* last one <= bw_cost_per_microframe */
 			bwb_table[i] = remainder;
 		}
-	} else if (is_fs_or_ls(udev->speed)) {
+	} else if (is_fs_or_ls(sch_ep->speed)) {
 		sch_ep->pkts = 1; /* at most one packet for each microframe */
 
 		/*
@@ -416,8 +417,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 	return 0;
 }
 
-static int check_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
@@ -485,8 +485,7 @@ static int check_sch_tt(struct usb_device *udev,
 	return check_fs_bus_bw(sch_ep, offset);
 }
 
-static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, bool used)
+static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
@@ -522,11 +521,11 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
-static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+static int load_ep_bw(struct mu3h_sch_bw_info *sch_bw,
 		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
 {
 	if (sch_ep->sch_tt)
-		update_sch_tt(udev, sch_ep, loaded);
+		update_sch_tt(sch_ep, loaded);
 
 	/* update bus bandwidth info */
 	update_bus_bw(sch_bw, sch_ep, loaded);
@@ -550,8 +549,8 @@ static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 	return boundary;
 }
 
-static int check_sch_bw(struct usb_device *udev,
-	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
+			struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
 	u32 min_bw;
@@ -574,7 +573,7 @@ static int check_sch_bw(struct usb_device *udev,
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (sch_ep->sch_tt) {
-			ret = check_sch_tt(udev, sch_ep, offset);
+			ret = check_sch_tt(sch_ep, offset);
 			if (ret)
 				continue;
 		}
@@ -593,7 +592,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	bw_boundary = get_bw_boundary(udev->speed);
+	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
@@ -602,7 +601,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	return load_ep_bw(udev, sch_bw, sch_ep, true);
+	return load_ep_bw(sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
@@ -610,7 +609,7 @@ static void destroy_sch_ep(struct usb_device *udev,
 {
 	/* only release ep bw check passed by check_sch_bw() */
 	if (sch_ep->allocated)
-		load_ep_bw(udev, sch_bw, sch_ep, false);
+		load_ep_bw(sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
@@ -711,7 +710,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (IS_ERR_OR_NULL(sch_ep))
 		return -ENOMEM;
 
-	setup_sch_info(udev, ep_ctx, sch_ep);
+	setup_sch_info(ep_ctx, sch_ep);
 
 	list_add_tail(&sch_ep->endpoint, &mtk->bw_ep_chk_list);
 
@@ -771,7 +770,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
 		sch_bw = &mtk->sch_array[bw_index];
 
-		ret = check_sch_bw(udev, sch_bw, sch_ep);
+		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
 			xhci_err(xhci, "Not enough bandwidth!\n");
 			return -ENOSPC;
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 076b9bbc89dd..d25bf9e49136 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -85,6 +85,7 @@ struct mu3h_sch_ep_info {
 	u32 ep_type;
 	u32 maxpkt;
 	struct usb_host_endpoint *ep;
+	enum usb_device_speed speed;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0

[PATCH v2 10/18] usb: xhci-mtk: add a member @speed in mu3h_sch_ep_info struct

[Chunfeng Yun]

This is used to drop parameter @udev for some functions,
meanwhile remove some unused @udev parameter.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++-----------------
 drivers/usb/host/xhci-mtk.h     |  1 +
 2 files changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 6fb7a040c73c..3dc727b820aa 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -214,14 +214,15 @@ static struct mu3h_sch_ep_info *create_sch_ep(struct usb_device *udev,
 
 	sch_ep->sch_tt = tt;
 	sch_ep->ep = ep;
+	sch_ep->speed = udev->speed;
 	INIT_LIST_HEAD(&sch_ep->endpoint);
 	INIT_LIST_HEAD(&sch_ep->tt_endpoint);
 
 	return sch_ep;
 }
 
-static void setup_sch_info(struct usb_device *udev,
-		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+static void setup_sch_info(struct xhci_ep_ctx *ep_ctx,
+			   struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 ep_type;
 	u32 maxpkt;
@@ -248,7 +249,7 @@ static void setup_sch_info(struct usb_device *udev,
 	sch_ep->burst_mode = 0;
 	sch_ep->repeat = 0;
 
-	if (udev->speed == USB_SPEED_HIGH) {
+	if (sch_ep->speed == USB_SPEED_HIGH) {
 		sch_ep->cs_count = 0;
 
 		/*
@@ -266,7 +267,7 @@ static void setup_sch_info(struct usb_device *udev,
 		sch_ep->pkts = max_burst + 1;
 		sch_ep->bw_cost_per_microframe = maxpkt * sch_ep->pkts;
 		bwb_table[0] = sch_ep->bw_cost_per_microframe;
-	} else if (udev->speed >= USB_SPEED_SUPER) {
+	} else if (sch_ep->speed >= USB_SPEED_SUPER) {
 		/* usb3_r1 spec section4.4.7 & 4.4.8 */
 		sch_ep->cs_count = 0;
 		sch_ep->burst_mode = 1;
@@ -311,7 +312,7 @@ static void setup_sch_info(struct usb_device *udev,
 			/* last one <= bw_cost_per_microframe */
 			bwb_table[i] = remainder;
 		}
-	} else if (is_fs_or_ls(udev->speed)) {
+	} else if (is_fs_or_ls(sch_ep->speed)) {
 		sch_ep->pkts = 1; /* at most one packet for each microframe */
 
 		/*
@@ -416,8 +417,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 	return 0;
 }
 
-static int check_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
@@ -485,8 +485,7 @@ static int check_sch_tt(struct usb_device *udev,
 	return check_fs_bus_bw(sch_ep, offset);
 }
 
-static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, bool used)
+static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
@@ -522,11 +521,11 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
-static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+static int load_ep_bw(struct mu3h_sch_bw_info *sch_bw,
 		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
 {
 	if (sch_ep->sch_tt)
-		update_sch_tt(udev, sch_ep, loaded);
+		update_sch_tt(sch_ep, loaded);
 
 	/* update bus bandwidth info */
 	update_bus_bw(sch_bw, sch_ep, loaded);
@@ -550,8 +549,8 @@ static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 	return boundary;
 }
 
-static int check_sch_bw(struct usb_device *udev,
-	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
+			struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
 	u32 min_bw;
@@ -574,7 +573,7 @@ static int check_sch_bw(struct usb_device *udev,
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (sch_ep->sch_tt) {
-			ret = check_sch_tt(udev, sch_ep, offset);
+			ret = check_sch_tt(sch_ep, offset);
 			if (ret)
 				continue;
 		}
@@ -593,7 +592,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	bw_boundary = get_bw_boundary(udev->speed);
+	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
@@ -602,7 +601,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	return load_ep_bw(udev, sch_bw, sch_ep, true);
+	return load_ep_bw(sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
@@ -610,7 +609,7 @@ static void destroy_sch_ep(struct usb_device *udev,
 {
 	/* only release ep bw check passed by check_sch_bw() */
 	if (sch_ep->allocated)
-		load_ep_bw(udev, sch_bw, sch_ep, false);
+		load_ep_bw(sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
@@ -711,7 +710,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (IS_ERR_OR_NULL(sch_ep))
 		return -ENOMEM;
 
-	setup_sch_info(udev, ep_ctx, sch_ep);
+	setup_sch_info(ep_ctx, sch_ep);
 
 	list_add_tail(&sch_ep->endpoint, &mtk->bw_ep_chk_list);
 
@@ -771,7 +770,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
 		sch_bw = &mtk->sch_array[bw_index];
 
-		ret = check_sch_bw(udev, sch_bw, sch_ep);
+		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
 			xhci_err(xhci, "Not enough bandwidth!\n");
 			return -ENOSPC;
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 076b9bbc89dd..d25bf9e49136 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -85,6 +85,7 @@ struct mu3h_sch_ep_info {
 	u32 ep_type;
 	u32 maxpkt;
 	struct usb_host_endpoint *ep;
+	enum usb_device_speed speed;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 10/18] usb: xhci-mtk: add a member @speed in mu3h_sch_ep_info struct

[Chunfeng Yun]

This is used to drop parameter @udev for some functions,
meanwhile remove some unused @udev parameter.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++-----------------
 drivers/usb/host/xhci-mtk.h     |  1 +
 2 files changed, 19 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 6fb7a040c73c..3dc727b820aa 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -214,14 +214,15 @@ static struct mu3h_sch_ep_info *create_sch_ep(struct usb_device *udev,
 
 	sch_ep->sch_tt = tt;
 	sch_ep->ep = ep;
+	sch_ep->speed = udev->speed;
 	INIT_LIST_HEAD(&sch_ep->endpoint);
 	INIT_LIST_HEAD(&sch_ep->tt_endpoint);
 
 	return sch_ep;
 }
 
-static void setup_sch_info(struct usb_device *udev,
-		struct xhci_ep_ctx *ep_ctx, struct mu3h_sch_ep_info *sch_ep)
+static void setup_sch_info(struct xhci_ep_ctx *ep_ctx,
+			   struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 ep_type;
 	u32 maxpkt;
@@ -248,7 +249,7 @@ static void setup_sch_info(struct usb_device *udev,
 	sch_ep->burst_mode = 0;
 	sch_ep->repeat = 0;
 
-	if (udev->speed == USB_SPEED_HIGH) {
+	if (sch_ep->speed == USB_SPEED_HIGH) {
 		sch_ep->cs_count = 0;
 
 		/*
@@ -266,7 +267,7 @@ static void setup_sch_info(struct usb_device *udev,
 		sch_ep->pkts = max_burst + 1;
 		sch_ep->bw_cost_per_microframe = maxpkt * sch_ep->pkts;
 		bwb_table[0] = sch_ep->bw_cost_per_microframe;
-	} else if (udev->speed >= USB_SPEED_SUPER) {
+	} else if (sch_ep->speed >= USB_SPEED_SUPER) {
 		/* usb3_r1 spec section4.4.7 & 4.4.8 */
 		sch_ep->cs_count = 0;
 		sch_ep->burst_mode = 1;
@@ -311,7 +312,7 @@ static void setup_sch_info(struct usb_device *udev,
 			/* last one <= bw_cost_per_microframe */
 			bwb_table[i] = remainder;
 		}
-	} else if (is_fs_or_ls(udev->speed)) {
+	} else if (is_fs_or_ls(sch_ep->speed)) {
 		sch_ep->pkts = 1; /* at most one packet for each microframe */
 
 		/*
@@ -416,8 +417,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 	return 0;
 }
 
-static int check_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, u32 offset)
+static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 extra_cs_count;
@@ -485,8 +485,7 @@ static int check_sch_tt(struct usb_device *udev,
 	return check_fs_bus_bw(sch_ep, offset);
 }
 
-static void update_sch_tt(struct usb_device *udev,
-	struct mu3h_sch_ep_info *sch_ep, bool used)
+static void update_sch_tt(struct mu3h_sch_ep_info *sch_ep, bool used)
 {
 	struct mu3h_sch_tt *tt = sch_ep->sch_tt;
 	u32 base, num_esit;
@@ -522,11 +521,11 @@ static void update_sch_tt(struct usb_device *udev,
 		list_del(&sch_ep->tt_endpoint);
 }
 
-static int load_ep_bw(struct usb_device *udev, struct mu3h_sch_bw_info *sch_bw,
+static int load_ep_bw(struct mu3h_sch_bw_info *sch_bw,
 		      struct mu3h_sch_ep_info *sch_ep, bool loaded)
 {
 	if (sch_ep->sch_tt)
-		update_sch_tt(udev, sch_ep, loaded);
+		update_sch_tt(sch_ep, loaded);
 
 	/* update bus bandwidth info */
 	update_bus_bw(sch_bw, sch_ep, loaded);
@@ -550,8 +549,8 @@ static u32 get_esit_boundary(struct mu3h_sch_ep_info *sch_ep)
 	return boundary;
 }
 
-static int check_sch_bw(struct usb_device *udev,
-	struct mu3h_sch_bw_info *sch_bw, struct mu3h_sch_ep_info *sch_ep)
+static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
+			struct mu3h_sch_ep_info *sch_ep)
 {
 	u32 offset;
 	u32 min_bw;
@@ -574,7 +573,7 @@ static int check_sch_bw(struct usb_device *udev,
 	esit_boundary = get_esit_boundary(sch_ep);
 	for (offset = 0; offset < sch_ep->esit; offset++) {
 		if (sch_ep->sch_tt) {
-			ret = check_sch_tt(udev, sch_ep, offset);
+			ret = check_sch_tt(sch_ep, offset);
 			if (ret)
 				continue;
 		}
@@ -593,7 +592,7 @@ static int check_sch_bw(struct usb_device *udev,
 			break;
 	}
 
-	bw_boundary = get_bw_boundary(udev->speed);
+	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
 		return -ERANGE;
@@ -602,7 +601,7 @@ static int check_sch_bw(struct usb_device *udev,
 	sch_ep->cs_count = min_cs_count;
 	sch_ep->num_budget_microframes = min_num_budget;
 
-	return load_ep_bw(udev, sch_bw, sch_ep, true);
+	return load_ep_bw(sch_bw, sch_ep, true);
 }
 
 static void destroy_sch_ep(struct usb_device *udev,
@@ -610,7 +609,7 @@ static void destroy_sch_ep(struct usb_device *udev,
 {
 	/* only release ep bw check passed by check_sch_bw() */
 	if (sch_ep->allocated)
-		load_ep_bw(udev, sch_bw, sch_ep, false);
+		load_ep_bw(sch_bw, sch_ep, false);
 
 	if (sch_ep->sch_tt)
 		drop_tt(udev);
@@ -711,7 +710,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (IS_ERR_OR_NULL(sch_ep))
 		return -ENOMEM;
 
-	setup_sch_info(udev, ep_ctx, sch_ep);
+	setup_sch_info(ep_ctx, sch_ep);
 
 	list_add_tail(&sch_ep->endpoint, &mtk->bw_ep_chk_list);
 
@@ -771,7 +770,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
 		sch_bw = &mtk->sch_array[bw_index];
 
-		ret = check_sch_bw(udev, sch_bw, sch_ep);
+		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
 			xhci_err(xhci, "Not enough bandwidth!\n");
 			return -ENOSPC;
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 076b9bbc89dd..d25bf9e49136 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -85,6 +85,7 @@ struct mu3h_sch_ep_info {
 	u32 ep_type;
 	u32 maxpkt;
 	struct usb_host_endpoint *ep;
+	enum usb_device_speed speed;
 	bool allocated;
 	/*
 	 * mtk xHCI scheduling information put into reserved DWs
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 11/18] usb: xhci-mtk: use @tt_info to check the FS/LS device is under a HS hub

[Chunfeng Yun]

If the LS/FS device is connected to an external HS hub, the member
@tt_info in xhci_virt_device struct in not NULL, use it to check
whether a LS/FS device is under an exernal HS hub, then no need get
the slot context of this device.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 3dc727b820aa..bad99580fb68 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -678,7 +678,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_ep_ctx *ep_ctx;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
@@ -686,7 +685,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
@@ -694,7 +692,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT)) {
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
 		 * set @bpkts to 1 if it is LS or FS periodic endpoint, and its
 		 * device does not connected through an external HS hub
@@ -723,7 +721,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
@@ -732,7 +729,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -740,7 +736,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
 	bw_index = get_bw_index(xhci, udev, ep);
-- 
2.18.0

[PATCH v2 11/18] usb: xhci-mtk: use @tt_info to check the FS/LS device is under a HS hub

[Chunfeng Yun]

If the LS/FS device is connected to an external HS hub, the member
@tt_info in xhci_virt_device struct in not NULL, use it to check
whether a LS/FS device is under an exernal HS hub, then no need get
the slot context of this device.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 3dc727b820aa..bad99580fb68 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -678,7 +678,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_ep_ctx *ep_ctx;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
@@ -686,7 +685,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
@@ -694,7 +692,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT)) {
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
 		 * set @bpkts to 1 if it is LS or FS periodic endpoint, and its
 		 * device does not connected through an external HS hub
@@ -723,7 +721,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
@@ -732,7 +729,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -740,7 +736,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
 	bw_index = get_bw_index(xhci, udev, ep);
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 11/18] usb: xhci-mtk: use @tt_info to check the FS/LS device is under a HS hub

[Chunfeng Yun]

If the LS/FS device is connected to an external HS hub, the member
@tt_info in xhci_virt_device struct in not NULL, use it to check
whether a LS/FS device is under an exernal HS hub, then no need get
the slot context of this device.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 3dc727b820aa..bad99580fb68 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -678,7 +678,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_ep_ctx *ep_ctx;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
@@ -686,7 +685,6 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
@@ -694,7 +692,7 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT)) {
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
 		 * set @bpkts to 1 if it is LS or FS periodic endpoint, and its
 		 * device does not connected through an external HS hub
@@ -723,7 +721,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
-	struct xhci_slot_ctx *slot_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
@@ -732,7 +729,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->in_ctx);
 	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -740,7 +736,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		usb_endpoint_maxp(&ep->desc),
 		usb_endpoint_dir_in(&ep->desc), ep);
 
-	if (!need_bw_sch(ep, udev->speed, slot_ctx->tt_info & TT_SLOT))
+	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
 	bw_index = get_bw_index(xhci, udev, ep);
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 12/18] usb: xhci-mtk: rebuild the way to get bandwidth domain

[Chunfeng Yun]

Rebuild the function get_bw_index(), get the bandwidth domain
directly instead its index of domain array.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 29 +++++++++++------------------
 1 file changed, 11 insertions(+), 18 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index bad99580fb68..9e77bbd8e7f7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -57,7 +57,7 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 }
 
 /*
-* get the index of bandwidth domains array which @ep belongs to.
+* get the bandwidth domain which @ep belongs to.
 *
 * the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
 * each HS root port is treated as a single bandwidth domain,
@@ -68,9 +68,11 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 * so the bandwidth domain array is organized as follow for simplification:
 * SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
 */
-static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
-	struct usb_host_endpoint *ep)
+static struct mu3h_sch_bw_info *
+get_bw_info(struct xhci_hcd_mtk *mtk, struct usb_device *udev,
+	    struct usb_host_endpoint *ep)
 {
+	struct xhci_hcd *xhci = hcd_to_xhci(mtk->hcd);
 	struct xhci_virt_device *virt_dev;
 	int bw_index;
 
@@ -86,7 +88,7 @@ static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
 		bw_index = virt_dev->real_port + xhci->usb3_rhub.num_ports - 1;
 	}
 
-	return bw_index;
+	return &mtk->sch_array[bw_index];
 }
 
 static u32 get_esit(struct xhci_ep_ctx *ep_ctx)
@@ -722,14 +724,11 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_virt_device *virt_dev;
-	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
 		__func__, usb_endpoint_type(&ep->desc), udev->speed,
@@ -739,8 +738,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
-	bw_index = get_bw_index(xhci, udev, ep);
-	sch_bw = &sch_array[bw_index];
+	sch_bw = get_bw_info(mtk, udev, ep);
 
 	list_for_each_entry_safe(sch_ep, tmp, &sch_bw->bw_ep_list, endpoint) {
 		if (sch_ep->ep == ep) {
@@ -758,13 +756,12 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_virt_device *virt_dev = xhci->devs[udev->slot_id];
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index, ret;
+	int ret;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry(sch_ep, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
@@ -778,9 +775,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		struct usb_host_endpoint *ep = sch_ep->ep;
 		unsigned int ep_index = xhci_get_endpoint_index(&ep->desc);
 
-		bw_index = get_bw_index(xhci, udev, ep);
-		sch_bw = &mtk->sch_array[bw_index];
-
+		sch_bw = get_bw_info(mtk, udev, ep);
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -805,13 +800,11 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry_safe(sch_ep, tmp, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 		destroy_sch_ep(udev, sch_bw, sch_ep);
 	}
 
-- 
2.18.0

[PATCH v2 12/18] usb: xhci-mtk: rebuild the way to get bandwidth domain

[Chunfeng Yun]

Rebuild the function get_bw_index(), get the bandwidth domain
directly instead its index of domain array.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 29 +++++++++++------------------
 1 file changed, 11 insertions(+), 18 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index bad99580fb68..9e77bbd8e7f7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -57,7 +57,7 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 }
 
 /*
-* get the index of bandwidth domains array which @ep belongs to.
+* get the bandwidth domain which @ep belongs to.
 *
 * the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
 * each HS root port is treated as a single bandwidth domain,
@@ -68,9 +68,11 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 * so the bandwidth domain array is organized as follow for simplification:
 * SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
 */
-static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
-	struct usb_host_endpoint *ep)
+static struct mu3h_sch_bw_info *
+get_bw_info(struct xhci_hcd_mtk *mtk, struct usb_device *udev,
+	    struct usb_host_endpoint *ep)
 {
+	struct xhci_hcd *xhci = hcd_to_xhci(mtk->hcd);
 	struct xhci_virt_device *virt_dev;
 	int bw_index;
 
@@ -86,7 +88,7 @@ static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
 		bw_index = virt_dev->real_port + xhci->usb3_rhub.num_ports - 1;
 	}
 
-	return bw_index;
+	return &mtk->sch_array[bw_index];
 }
 
 static u32 get_esit(struct xhci_ep_ctx *ep_ctx)
@@ -722,14 +724,11 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_virt_device *virt_dev;
-	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
 		__func__, usb_endpoint_type(&ep->desc), udev->speed,
@@ -739,8 +738,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
-	bw_index = get_bw_index(xhci, udev, ep);
-	sch_bw = &sch_array[bw_index];
+	sch_bw = get_bw_info(mtk, udev, ep);
 
 	list_for_each_entry_safe(sch_ep, tmp, &sch_bw->bw_ep_list, endpoint) {
 		if (sch_ep->ep == ep) {
@@ -758,13 +756,12 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_virt_device *virt_dev = xhci->devs[udev->slot_id];
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index, ret;
+	int ret;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry(sch_ep, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
@@ -778,9 +775,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		struct usb_host_endpoint *ep = sch_ep->ep;
 		unsigned int ep_index = xhci_get_endpoint_index(&ep->desc);
 
-		bw_index = get_bw_index(xhci, udev, ep);
-		sch_bw = &mtk->sch_array[bw_index];
-
+		sch_bw = get_bw_info(mtk, udev, ep);
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -805,13 +800,11 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry_safe(sch_ep, tmp, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 		destroy_sch_ep(udev, sch_bw, sch_ep);
 	}
 
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 12/18] usb: xhci-mtk: rebuild the way to get bandwidth domain

[Chunfeng Yun]

Rebuild the function get_bw_index(), get the bandwidth domain
directly instead its index of domain array.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 29 +++++++++++------------------
 1 file changed, 11 insertions(+), 18 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index bad99580fb68..9e77bbd8e7f7 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -57,7 +57,7 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 }
 
 /*
-* get the index of bandwidth domains array which @ep belongs to.
+* get the bandwidth domain which @ep belongs to.
 *
 * the bandwidth domain array is saved to @sch_array of struct xhci_hcd_mtk,
 * each HS root port is treated as a single bandwidth domain,
@@ -68,9 +68,11 @@ static u32 get_bw_boundary(enum usb_device_speed speed)
 * so the bandwidth domain array is organized as follow for simplification:
 * SSport0-OUT, SSport0-IN, ..., SSportX-OUT, SSportX-IN, HSport0, ..., HSportY
 */
-static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
-	struct usb_host_endpoint *ep)
+static struct mu3h_sch_bw_info *
+get_bw_info(struct xhci_hcd_mtk *mtk, struct usb_device *udev,
+	    struct usb_host_endpoint *ep)
 {
+	struct xhci_hcd *xhci = hcd_to_xhci(mtk->hcd);
 	struct xhci_virt_device *virt_dev;
 	int bw_index;
 
@@ -86,7 +88,7 @@ static int get_bw_index(struct xhci_hcd *xhci, struct usb_device *udev,
 		bw_index = virt_dev->real_port + xhci->usb3_rhub.num_ports - 1;
 	}
 
-	return bw_index;
+	return &mtk->sch_array[bw_index];
 }
 
 static u32 get_esit(struct xhci_ep_ctx *ep_ctx)
@@ -722,14 +724,11 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
 	struct xhci_hcd *xhci;
 	struct xhci_virt_device *virt_dev;
-	struct mu3h_sch_bw_info *sch_array;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
-	sch_array = mtk->sch_array;
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
 		__func__, usb_endpoint_type(&ep->desc), udev->speed,
@@ -739,8 +738,7 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
 
-	bw_index = get_bw_index(xhci, udev, ep);
-	sch_bw = &sch_array[bw_index];
+	sch_bw = get_bw_info(mtk, udev, ep);
 
 	list_for_each_entry_safe(sch_ep, tmp, &sch_bw->bw_ep_list, endpoint) {
 		if (sch_ep->ep == ep) {
@@ -758,13 +756,12 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_virt_device *virt_dev = xhci->devs[udev->slot_id];
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index, ret;
+	int ret;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry(sch_ep, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
@@ -778,9 +775,7 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 		struct usb_host_endpoint *ep = sch_ep->ep;
 		unsigned int ep_index = xhci_get_endpoint_index(&ep->desc);
 
-		bw_index = get_bw_index(xhci, udev, ep);
-		sch_bw = &mtk->sch_array[bw_index];
-
+		sch_bw = get_bw_info(mtk, udev, ep);
 		list_move_tail(&sch_ep->endpoint, &sch_bw->bw_ep_list);
 
 		ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -805,13 +800,11 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
-	int bw_index;
 
 	xhci_dbg(xhci, "%s() udev %s\n", __func__, dev_name(&udev->dev));
 
 	list_for_each_entry_safe(sch_ep, tmp, &mtk->bw_ep_chk_list, endpoint) {
-		bw_index = get_bw_index(xhci, udev, sch_ep->ep);
-		sch_bw = &mtk->sch_array[bw_index];
+		sch_bw = get_bw_info(mtk, udev, sch_ep->ep);
 		destroy_sch_ep(udev, sch_bw, sch_ep);
 	}
 
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 13/18] usb: xhci-mtk: add some schedule error number

[Chunfeng Yun]

This is used to provide more information about which case
causes bandwidth schedule failure.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 44 ++++++++++++++++++++++++++-------
 1 file changed, 35 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9e77bbd8e7f7..7b45441f2606 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,13 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+/* schedule error type */
+#define ESCH_SS_Y6		1001
+#define ESCH_SS_OVERLAP		1002
+#define ESCH_CS_OVERFLOW	1003
+#define ESCH_BW_OVERFLOW	1004
+#define ESCH_FIXME		1005
+
 /* mtk scheduler bitmasks */
 #define EP_BPKTS(p)	((p) & 0x7f)
 #define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
@@ -32,6 +39,24 @@
 #define EP_BOFFSET(p)	((p) & 0x3fff)
 #define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
 
+static char *sch_error_string(int err_num)
+{
+	switch (err_num) {
+	case ESCH_SS_Y6:
+		return "Can't schedule Start-Split in Y6";
+	case ESCH_SS_OVERLAP:
+		return "Can't find a suitable Start-Split location";
+	case ESCH_CS_OVERFLOW:
+		return "The last Complete-Split is greater than 7";
+	case ESCH_BW_OVERFLOW:
+		return "Bandwidth exceeds the maximum limit";
+	case ESCH_FIXME:
+		return "FIXME, to be resolved";
+	default:
+		return "Unknown";
+	}
+}
+
 static int is_fs_or_ls(enum usb_device_speed speed)
 {
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
@@ -412,7 +437,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 		for (j = 0; j < sch_ep->cs_count; j++) {
 			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
 			if (tmp > FS_PAYLOAD_MAX)
-				return -ERANGE;
+				return -ESCH_BW_OVERFLOW;
 		}
 	}
 
@@ -437,11 +462,11 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (!(start_ss == 7 || last_ss < 6))
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
 			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
+				return -ESCH_SS_OVERLAP;
 
 	} else {
 		u32 cs_count = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
@@ -451,14 +476,14 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (start_ss == 6)
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		/* one uframe for ss + one uframe for idle */
 		start_cs = (start_ss + 2) % 8;
 		last_cs = start_cs + cs_count - 1;
 
 		if (last_cs > 7)
-			return -ERANGE;
+			return -ESCH_CS_OVERFLOW;
 
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
@@ -470,7 +495,7 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 			cs_count = 7; /* HW limit */
 
 		if (test_bit(offset, tt->ss_bit_map))
-			return -ERANGE;
+			return -ESCH_SS_OVERLAP;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
@@ -562,7 +587,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	int ret;
+	int ret = 0;
 
 	/*
 	 * Search through all possible schedule microframes.
@@ -597,7 +622,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
-		return -ERANGE;
+		return ret ? ret : -ESCH_BW_OVERFLOW;
 
 	sch_ep->offset = min_index;
 	sch_ep->cs_count = min_cs_count;
@@ -765,7 +790,8 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
-			xhci_err(xhci, "Not enough bandwidth!\n");
+			xhci_err(xhci, "Not enough bandwidth! (%s)\n",
+				 sch_error_string(-ret));
 			return -ENOSPC;
 		}
 	}
-- 
2.18.0

[PATCH v2 13/18] usb: xhci-mtk: add some schedule error number

[Chunfeng Yun]

This is used to provide more information about which case
causes bandwidth schedule failure.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 44 ++++++++++++++++++++++++++-------
 1 file changed, 35 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9e77bbd8e7f7..7b45441f2606 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,13 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+/* schedule error type */
+#define ESCH_SS_Y6		1001
+#define ESCH_SS_OVERLAP		1002
+#define ESCH_CS_OVERFLOW	1003
+#define ESCH_BW_OVERFLOW	1004
+#define ESCH_FIXME		1005
+
 /* mtk scheduler bitmasks */
 #define EP_BPKTS(p)	((p) & 0x7f)
 #define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
@@ -32,6 +39,24 @@
 #define EP_BOFFSET(p)	((p) & 0x3fff)
 #define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
 
+static char *sch_error_string(int err_num)
+{
+	switch (err_num) {
+	case ESCH_SS_Y6:
+		return "Can't schedule Start-Split in Y6";
+	case ESCH_SS_OVERLAP:
+		return "Can't find a suitable Start-Split location";
+	case ESCH_CS_OVERFLOW:
+		return "The last Complete-Split is greater than 7";
+	case ESCH_BW_OVERFLOW:
+		return "Bandwidth exceeds the maximum limit";
+	case ESCH_FIXME:
+		return "FIXME, to be resolved";
+	default:
+		return "Unknown";
+	}
+}
+
 static int is_fs_or_ls(enum usb_device_speed speed)
 {
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
@@ -412,7 +437,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 		for (j = 0; j < sch_ep->cs_count; j++) {
 			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
 			if (tmp > FS_PAYLOAD_MAX)
-				return -ERANGE;
+				return -ESCH_BW_OVERFLOW;
 		}
 	}
 
@@ -437,11 +462,11 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (!(start_ss == 7 || last_ss < 6))
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
 			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
+				return -ESCH_SS_OVERLAP;
 
 	} else {
 		u32 cs_count = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
@@ -451,14 +476,14 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (start_ss == 6)
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		/* one uframe for ss + one uframe for idle */
 		start_cs = (start_ss + 2) % 8;
 		last_cs = start_cs + cs_count - 1;
 
 		if (last_cs > 7)
-			return -ERANGE;
+			return -ESCH_CS_OVERFLOW;
 
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
@@ -470,7 +495,7 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 			cs_count = 7; /* HW limit */
 
 		if (test_bit(offset, tt->ss_bit_map))
-			return -ERANGE;
+			return -ESCH_SS_OVERLAP;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
@@ -562,7 +587,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	int ret;
+	int ret = 0;
 
 	/*
 	 * Search through all possible schedule microframes.
@@ -597,7 +622,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
-		return -ERANGE;
+		return ret ? ret : -ESCH_BW_OVERFLOW;
 
 	sch_ep->offset = min_index;
 	sch_ep->cs_count = min_cs_count;
@@ -765,7 +790,8 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
-			xhci_err(xhci, "Not enough bandwidth!\n");
+			xhci_err(xhci, "Not enough bandwidth! (%s)\n",
+				 sch_error_string(-ret));
 			return -ENOSPC;
 		}
 	}
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 13/18] usb: xhci-mtk: add some schedule error number

[Chunfeng Yun]

This is used to provide more information about which case
causes bandwidth schedule failure.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 44 ++++++++++++++++++++++++++-------
 1 file changed, 35 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 9e77bbd8e7f7..7b45441f2606 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,13 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+/* schedule error type */
+#define ESCH_SS_Y6		1001
+#define ESCH_SS_OVERLAP		1002
+#define ESCH_CS_OVERFLOW	1003
+#define ESCH_BW_OVERFLOW	1004
+#define ESCH_FIXME		1005
+
 /* mtk scheduler bitmasks */
 #define EP_BPKTS(p)	((p) & 0x7f)
 #define EP_BCSCOUNT(p)	(((p) & 0x7) << 8)
@@ -32,6 +39,24 @@
 #define EP_BOFFSET(p)	((p) & 0x3fff)
 #define EP_BREPEAT(p)	(((p) & 0x7fff) << 16)
 
+static char *sch_error_string(int err_num)
+{
+	switch (err_num) {
+	case ESCH_SS_Y6:
+		return "Can't schedule Start-Split in Y6";
+	case ESCH_SS_OVERLAP:
+		return "Can't find a suitable Start-Split location";
+	case ESCH_CS_OVERFLOW:
+		return "The last Complete-Split is greater than 7";
+	case ESCH_BW_OVERFLOW:
+		return "Bandwidth exceeds the maximum limit";
+	case ESCH_FIXME:
+		return "FIXME, to be resolved";
+	default:
+		return "Unknown";
+	}
+}
+
 static int is_fs_or_ls(enum usb_device_speed speed)
 {
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
@@ -412,7 +437,7 @@ static int check_fs_bus_bw(struct mu3h_sch_ep_info *sch_ep, int offset)
 		for (j = 0; j < sch_ep->cs_count; j++) {
 			tmp = tt->fs_bus_bw[base + j] + sch_ep->bw_cost_per_microframe;
 			if (tmp > FS_PAYLOAD_MAX)
-				return -ERANGE;
+				return -ESCH_BW_OVERFLOW;
 		}
 	}
 
@@ -437,11 +462,11 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (!(start_ss == 7 || last_ss < 6))
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		for (i = 0; i < sch_ep->cs_count; i++)
 			if (test_bit(offset + i, tt->ss_bit_map))
-				return -ERANGE;
+				return -ESCH_SS_OVERLAP;
 
 	} else {
 		u32 cs_count = DIV_ROUND_UP(sch_ep->maxpkt, FS_PAYLOAD_MAX);
@@ -451,14 +476,14 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 		 * must never schedule Start-Split in Y6
 		 */
 		if (start_ss == 6)
-			return -ERANGE;
+			return -ESCH_SS_Y6;
 
 		/* one uframe for ss + one uframe for idle */
 		start_cs = (start_ss + 2) % 8;
 		last_cs = start_cs + cs_count - 1;
 
 		if (last_cs > 7)
-			return -ERANGE;
+			return -ESCH_CS_OVERFLOW;
 
 		if (sch_ep->ep_type == ISOC_IN_EP)
 			extra_cs_count = (last_cs == 7) ? 1 : 2;
@@ -470,7 +495,7 @@ static int check_sch_tt(struct mu3h_sch_ep_info *sch_ep, u32 offset)
 			cs_count = 7; /* HW limit */
 
 		if (test_bit(offset, tt->ss_bit_map))
-			return -ERANGE;
+			return -ESCH_SS_OVERLAP;
 
 		sch_ep->cs_count = cs_count;
 		/* one for ss, the other for idle */
@@ -562,7 +587,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	u32 esit_boundary;
 	u32 min_num_budget;
 	u32 min_cs_count;
-	int ret;
+	int ret = 0;
 
 	/*
 	 * Search through all possible schedule microframes.
@@ -597,7 +622,7 @@ static int check_sch_bw(struct mu3h_sch_bw_info *sch_bw,
 	bw_boundary = get_bw_boundary(sch_ep->speed);
 	/* check bandwidth */
 	if (min_bw > bw_boundary)
-		return -ERANGE;
+		return ret ? ret : -ESCH_BW_OVERFLOW;
 
 	sch_ep->offset = min_index;
 	sch_ep->cs_count = min_cs_count;
@@ -765,7 +790,8 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 		ret = check_sch_bw(sch_bw, sch_ep);
 		if (ret) {
-			xhci_err(xhci, "Not enough bandwidth!\n");
+			xhci_err(xhci, "Not enough bandwidth! (%s)\n",
+				 sch_error_string(-ret));
 			return -ENOSPC;
 		}
 	}
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 14/18] usb: xhci-mtk: remove declaration of xhci_mtk_setup()

[Chunfeng Yun]

Move xhci_driver_overrides struct variable after definition
of xhci_mtk_setup(), then we can remove it's declaration.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fe010cc61f19..fb4e56f6a6c3 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -344,15 +344,6 @@ static void usb_wakeup_set(struct xhci_hcd_mtk *mtk, bool enable)
 		usb_wakeup_ip_sleep_set(mtk, enable);
 }
 
-static int xhci_mtk_setup(struct usb_hcd *hcd);
-static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
-	.reset = xhci_mtk_setup,
-	.check_bandwidth = xhci_mtk_check_bandwidth,
-	.reset_bandwidth = xhci_mtk_reset_bandwidth,
-};
-
-static struct hc_driver __read_mostly xhci_mtk_hc_driver;
-
 static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
 {
 	int ret;
@@ -424,6 +415,14 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 	return ret;
 }
 
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.reset = xhci_mtk_setup,
+	.check_bandwidth = xhci_mtk_check_bandwidth,
+	.reset_bandwidth = xhci_mtk_reset_bandwidth,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
 static int xhci_mtk_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-- 
2.18.0

[PATCH v2 14/18] usb: xhci-mtk: remove declaration of xhci_mtk_setup()

[Chunfeng Yun]

Move xhci_driver_overrides struct variable after definition
of xhci_mtk_setup(), then we can remove it's declaration.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fe010cc61f19..fb4e56f6a6c3 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -344,15 +344,6 @@ static void usb_wakeup_set(struct xhci_hcd_mtk *mtk, bool enable)
 		usb_wakeup_ip_sleep_set(mtk, enable);
 }
 
-static int xhci_mtk_setup(struct usb_hcd *hcd);
-static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
-	.reset = xhci_mtk_setup,
-	.check_bandwidth = xhci_mtk_check_bandwidth,
-	.reset_bandwidth = xhci_mtk_reset_bandwidth,
-};
-
-static struct hc_driver __read_mostly xhci_mtk_hc_driver;
-
 static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
 {
 	int ret;
@@ -424,6 +415,14 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 	return ret;
 }
 
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.reset = xhci_mtk_setup,
+	.check_bandwidth = xhci_mtk_check_bandwidth,
+	.reset_bandwidth = xhci_mtk_reset_bandwidth,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
 static int xhci_mtk_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 14/18] usb: xhci-mtk: remove declaration of xhci_mtk_setup()

[Chunfeng Yun]

Move xhci_driver_overrides struct variable after definition
of xhci_mtk_setup(), then we can remove it's declaration.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk.c | 17 ++++++++---------
 1 file changed, 8 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fe010cc61f19..fb4e56f6a6c3 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -344,15 +344,6 @@ static void usb_wakeup_set(struct xhci_hcd_mtk *mtk, bool enable)
 		usb_wakeup_ip_sleep_set(mtk, enable);
 }
 
-static int xhci_mtk_setup(struct usb_hcd *hcd);
-static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
-	.reset = xhci_mtk_setup,
-	.check_bandwidth = xhci_mtk_check_bandwidth,
-	.reset_bandwidth = xhci_mtk_reset_bandwidth,
-};
-
-static struct hc_driver __read_mostly xhci_mtk_hc_driver;
-
 static int xhci_mtk_ldos_enable(struct xhci_hcd_mtk *mtk)
 {
 	int ret;
@@ -424,6 +415,14 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 	return ret;
 }
 
+static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
+	.reset = xhci_mtk_setup,
+	.check_bandwidth = xhci_mtk_check_bandwidth,
+	.reset_bandwidth = xhci_mtk_reset_bandwidth,
+};
+
+static struct hc_driver __read_mostly xhci_mtk_hc_driver;
+
 static int xhci_mtk_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Chunfeng Yun]

Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/Makefile       |  6 ++---
 drivers/usb/host/xhci-mem.c     |  2 +-
 drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
 drivers/usb/host/xhci-mtk.c     |  2 ++
 drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
 drivers/usb/host/xhci-ring.c    |  1 -
 drivers/usb/host/xhci.c         | 30 +++++++++------------
 drivers/usb/host/xhci.h         |  8 ++++++
 8 files changed, 64 insertions(+), 66 deletions(-)

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3e4d298d851f..171de4df50bd 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -19,9 +19,7 @@ ifneq ($(CONFIG_USB_XHCI_DBGCAP), )
 	xhci-hcd-y += xhci-dbgcap.o xhci-dbgtty.o
 endif
 
-ifneq ($(CONFIG_USB_XHCI_MTK), )
-	xhci-hcd-y += xhci-mtk-sch.o
-endif
+xhci-mtk-hcd-y := xhci-mtk.o xhci-mtk-sch.o
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -73,7 +71,7 @@ obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PCI_RENESAS)	+= xhci-pci-renesas.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
 obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
-obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk-hcd.o
 obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index f2c4ee7c4786..7eb8c07c8418 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -532,7 +532,7 @@ struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci,
 	return (struct xhci_ep_ctx *)
 		(ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params)));
 }
-
+EXPORT_SYMBOL_GPL(xhci_get_ep_ctx);
 
 /***************** Streams structures manipulation *************************/
 
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 7b45441f2606..046b7f1ebf94 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -691,25 +691,22 @@ int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk)
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
 
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk)
 {
 	kfree(mtk->sch_array);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
 
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_ep_ctx *ep_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -741,18 +738,16 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
 
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			  struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -772,7 +767,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		}
 	}
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
 
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -818,7 +812,6 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return xhci_check_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_check_bandwidth);
 
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -836,4 +829,31 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	xhci_reset_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_reset_bandwidth);
+
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_add_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	if (ep->hcpriv)
+		ret = add_ep_quirk(hcd, udev, ep);
+
+	return ret;
+}
+
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_drop_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	drop_ep_quirk(hcd, udev, ep);
+	return 0;
+}
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fb4e56f6a6c3..57bcfdfa0465 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -417,6 +417,8 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 
 static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
 	.reset = xhci_mtk_setup,
+	.add_endpoint = xhci_mtk_add_ep,
+	.drop_endpoint = xhci_mtk_drop_ep,
 	.check_bandwidth = xhci_mtk_check_bandwidth,
 	.reset_bandwidth = xhci_mtk_reset_bandwidth,
 };
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index d25bf9e49136..621ec1a85009 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -161,38 +161,13 @@ static inline struct xhci_hcd_mtk *hcd_to_mtk(struct usb_hcd *hcd)
 	return dev_get_drvdata(hcd->self.controller);
 }
 
-#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
 int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk);
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk);
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep);
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep);
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 
-#else
-static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-}
-
-static inline int xhci_mtk_check_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-}
-#endif
-
 #endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 5e548a1c93ab..c8a880111435 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -57,7 +57,6 @@
 #include <linux/dma-mapping.h>
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 
 static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd,
 			 u32 field1, u32 field2,
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index bd27bd670104..13baeda927f0 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -20,7 +20,6 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 #include "xhci-debugfs.h"
 #include "xhci-dbgcap.h"
 
@@ -1420,6 +1419,7 @@ unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc)
 			(usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
 	return index;
 }
+EXPORT_SYMBOL_GPL(xhci_get_endpoint_index);
 
 /* The reverse operation to xhci_get_endpoint_index. Calculate the USB endpoint
  * address from the XHCI endpoint index.
@@ -1852,8 +1852,8 @@ static int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
  * disabled, so there's no need for mutual exclusion to protect
  * the xhci->devs[slot_id] structure.
  */
-static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx, *out_ctx;
@@ -1913,9 +1913,6 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
-	if (xhci->quirks & XHCI_MTK_HOST)
-		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
-
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1923,6 +1920,7 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_drop_endpoint);
 
 /* Add an endpoint to a new possible bandwidth configuration for this device.
  * Only one call to this function is allowed per endpoint before
@@ -1937,8 +1935,8 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
  * configuration or alt setting is installed in the device, so there's no need
  * for mutual exclusion to protect the xhci->devs[slot_id] structure.
  */
-static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx;
@@ -2012,15 +2010,6 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
-	if (xhci->quirks & XHCI_MTK_HOST) {
-		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
-		if (ret < 0) {
-			xhci_ring_free(xhci, virt_dev->eps[ep_index].new_ring);
-			virt_dev->eps[ep_index].new_ring = NULL;
-			return ret;
-		}
-	}
-
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
@@ -2045,6 +2034,7 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_add_endpoint);
 
 static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
 {
@@ -3078,6 +3068,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(xhci_check_bandwidth);
 
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -3102,6 +3093,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	}
 	xhci_zero_in_ctx(xhci, virt_dev);
 }
+EXPORT_SYMBOL_GPL(xhci_reset_bandwidth);
 
 static void xhci_setup_input_ctx_for_config_ep(struct xhci_hcd *xhci,
 		struct xhci_container_ctx *in_ctx,
@@ -5428,6 +5420,10 @@ void xhci_init_driver(struct hc_driver *drv,
 			drv->reset = over->reset;
 		if (over->start)
 			drv->start = over->start;
+		if (over->add_endpoint)
+			drv->add_endpoint = over->add_endpoint;
+		if (over->drop_endpoint)
+			drv->drop_endpoint = over->drop_endpoint;
 		if (over->check_bandwidth)
 			drv->check_bandwidth = over->check_bandwidth;
 		if (over->reset_bandwidth)
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index d41de5dc0452..5053c1adda1e 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1928,6 +1928,10 @@ struct xhci_driver_overrides {
 	size_t extra_priv_size;
 	int (*reset)(struct usb_hcd *hcd);
 	int (*start)(struct usb_hcd *hcd);
+	int (*add_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			    struct usb_host_endpoint *ep);
+	int (*drop_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			     struct usb_host_endpoint *ep);
 	int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
 	void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
 };
@@ -2080,6 +2084,10 @@ int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
 void xhci_shutdown(struct usb_hcd *hcd);
 void xhci_init_driver(struct hc_driver *drv,
 		      const struct xhci_driver_overrides *over);
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep);
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
-- 
2.18.0

[PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Chunfeng Yun]

Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/Makefile       |  6 ++---
 drivers/usb/host/xhci-mem.c     |  2 +-
 drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
 drivers/usb/host/xhci-mtk.c     |  2 ++
 drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
 drivers/usb/host/xhci-ring.c    |  1 -
 drivers/usb/host/xhci.c         | 30 +++++++++------------
 drivers/usb/host/xhci.h         |  8 ++++++
 8 files changed, 64 insertions(+), 66 deletions(-)

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3e4d298d851f..171de4df50bd 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -19,9 +19,7 @@ ifneq ($(CONFIG_USB_XHCI_DBGCAP), )
 	xhci-hcd-y += xhci-dbgcap.o xhci-dbgtty.o
 endif
 
-ifneq ($(CONFIG_USB_XHCI_MTK), )
-	xhci-hcd-y += xhci-mtk-sch.o
-endif
+xhci-mtk-hcd-y := xhci-mtk.o xhci-mtk-sch.o
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -73,7 +71,7 @@ obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PCI_RENESAS)	+= xhci-pci-renesas.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
 obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
-obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk-hcd.o
 obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index f2c4ee7c4786..7eb8c07c8418 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -532,7 +532,7 @@ struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci,
 	return (struct xhci_ep_ctx *)
 		(ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params)));
 }
-
+EXPORT_SYMBOL_GPL(xhci_get_ep_ctx);
 
 /***************** Streams structures manipulation *************************/
 
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 7b45441f2606..046b7f1ebf94 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -691,25 +691,22 @@ int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk)
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
 
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk)
 {
 	kfree(mtk->sch_array);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
 
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_ep_ctx *ep_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -741,18 +738,16 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
 
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			  struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -772,7 +767,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		}
 	}
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
 
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -818,7 +812,6 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return xhci_check_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_check_bandwidth);
 
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -836,4 +829,31 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	xhci_reset_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_reset_bandwidth);
+
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_add_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	if (ep->hcpriv)
+		ret = add_ep_quirk(hcd, udev, ep);
+
+	return ret;
+}
+
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_drop_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	drop_ep_quirk(hcd, udev, ep);
+	return 0;
+}
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fb4e56f6a6c3..57bcfdfa0465 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -417,6 +417,8 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 
 static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
 	.reset = xhci_mtk_setup,
+	.add_endpoint = xhci_mtk_add_ep,
+	.drop_endpoint = xhci_mtk_drop_ep,
 	.check_bandwidth = xhci_mtk_check_bandwidth,
 	.reset_bandwidth = xhci_mtk_reset_bandwidth,
 };
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index d25bf9e49136..621ec1a85009 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -161,38 +161,13 @@ static inline struct xhci_hcd_mtk *hcd_to_mtk(struct usb_hcd *hcd)
 	return dev_get_drvdata(hcd->self.controller);
 }
 
-#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
 int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk);
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk);
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep);
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep);
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 
-#else
-static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-}
-
-static inline int xhci_mtk_check_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-}
-#endif
-
 #endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 5e548a1c93ab..c8a880111435 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -57,7 +57,6 @@
 #include <linux/dma-mapping.h>
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 
 static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd,
 			 u32 field1, u32 field2,
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index bd27bd670104..13baeda927f0 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -20,7 +20,6 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 #include "xhci-debugfs.h"
 #include "xhci-dbgcap.h"
 
@@ -1420,6 +1419,7 @@ unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc)
 			(usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
 	return index;
 }
+EXPORT_SYMBOL_GPL(xhci_get_endpoint_index);
 
 /* The reverse operation to xhci_get_endpoint_index. Calculate the USB endpoint
  * address from the XHCI endpoint index.
@@ -1852,8 +1852,8 @@ static int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
  * disabled, so there's no need for mutual exclusion to protect
  * the xhci->devs[slot_id] structure.
  */
-static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx, *out_ctx;
@@ -1913,9 +1913,6 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
-	if (xhci->quirks & XHCI_MTK_HOST)
-		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
-
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1923,6 +1920,7 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_drop_endpoint);
 
 /* Add an endpoint to a new possible bandwidth configuration for this device.
  * Only one call to this function is allowed per endpoint before
@@ -1937,8 +1935,8 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
  * configuration or alt setting is installed in the device, so there's no need
  * for mutual exclusion to protect the xhci->devs[slot_id] structure.
  */
-static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx;
@@ -2012,15 +2010,6 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
-	if (xhci->quirks & XHCI_MTK_HOST) {
-		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
-		if (ret < 0) {
-			xhci_ring_free(xhci, virt_dev->eps[ep_index].new_ring);
-			virt_dev->eps[ep_index].new_ring = NULL;
-			return ret;
-		}
-	}
-
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
@@ -2045,6 +2034,7 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_add_endpoint);
 
 static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
 {
@@ -3078,6 +3068,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(xhci_check_bandwidth);
 
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -3102,6 +3093,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	}
 	xhci_zero_in_ctx(xhci, virt_dev);
 }
+EXPORT_SYMBOL_GPL(xhci_reset_bandwidth);
 
 static void xhci_setup_input_ctx_for_config_ep(struct xhci_hcd *xhci,
 		struct xhci_container_ctx *in_ctx,
@@ -5428,6 +5420,10 @@ void xhci_init_driver(struct hc_driver *drv,
 			drv->reset = over->reset;
 		if (over->start)
 			drv->start = over->start;
+		if (over->add_endpoint)
+			drv->add_endpoint = over->add_endpoint;
+		if (over->drop_endpoint)
+			drv->drop_endpoint = over->drop_endpoint;
 		if (over->check_bandwidth)
 			drv->check_bandwidth = over->check_bandwidth;
 		if (over->reset_bandwidth)
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index d41de5dc0452..5053c1adda1e 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1928,6 +1928,10 @@ struct xhci_driver_overrides {
 	size_t extra_priv_size;
 	int (*reset)(struct usb_hcd *hcd);
 	int (*start)(struct usb_hcd *hcd);
+	int (*add_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			    struct usb_host_endpoint *ep);
+	int (*drop_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			     struct usb_host_endpoint *ep);
 	int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
 	void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
 };
@@ -2080,6 +2084,10 @@ int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
 void xhci_shutdown(struct usb_hcd *hcd);
 void xhci_init_driver(struct hc_driver *drv,
 		      const struct xhci_driver_overrides *over);
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep);
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Chunfeng Yun]

Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
is not flexible for some cases. For example:
USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
implement extended functions if only update xhci-mtk.ko
This patch is used to remove the dependence.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/Makefile       |  6 ++---
 drivers/usb/host/xhci-mem.c     |  2 +-
 drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
 drivers/usb/host/xhci-mtk.c     |  2 ++
 drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
 drivers/usb/host/xhci-ring.c    |  1 -
 drivers/usb/host/xhci.c         | 30 +++++++++------------
 drivers/usb/host/xhci.h         |  8 ++++++
 8 files changed, 64 insertions(+), 66 deletions(-)

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 3e4d298d851f..171de4df50bd 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -19,9 +19,7 @@ ifneq ($(CONFIG_USB_XHCI_DBGCAP), )
 	xhci-hcd-y += xhci-dbgcap.o xhci-dbgtty.o
 endif
 
-ifneq ($(CONFIG_USB_XHCI_MTK), )
-	xhci-hcd-y += xhci-mtk-sch.o
-endif
+xhci-mtk-hcd-y := xhci-mtk.o xhci-mtk-sch.o
 
 xhci-plat-hcd-y := xhci-plat.o
 ifneq ($(CONFIG_USB_XHCI_MVEBU), )
@@ -73,7 +71,7 @@ obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
 obj-$(CONFIG_USB_XHCI_PCI_RENESAS)	+= xhci-pci-renesas.o
 obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
 obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
-obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
+obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk-hcd.o
 obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
 obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
 obj-$(CONFIG_USB_SL811_CS)	+= sl811_cs.o
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index f2c4ee7c4786..7eb8c07c8418 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -532,7 +532,7 @@ struct xhci_ep_ctx *xhci_get_ep_ctx(struct xhci_hcd *xhci,
 	return (struct xhci_ep_ctx *)
 		(ctx->bytes + (ep_index * CTX_SIZE(xhci->hcc_params)));
 }
-
+EXPORT_SYMBOL_GPL(xhci_get_ep_ctx);
 
 /***************** Streams structures manipulation *************************/
 
diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 7b45441f2606..046b7f1ebf94 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -691,25 +691,22 @@ int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk)
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_init);
 
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk)
 {
 	kfree(mtk->sch_array);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_sch_exit);
 
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_ep_ctx *ep_ctx;
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_ep_info *sch_ep;
 	unsigned int ep_index;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
@@ -741,18 +738,16 @@ int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	return 0;
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_add_ep_quirk);
 
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
+			  struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
-	struct xhci_hcd *xhci;
+	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
 	struct xhci_virt_device *virt_dev;
 	struct mu3h_sch_bw_info *sch_bw;
 	struct mu3h_sch_ep_info *sch_ep, *tmp;
 
-	xhci = hcd_to_xhci(hcd);
 	virt_dev = xhci->devs[udev->slot_id];
 
 	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
@@ -772,7 +767,6 @@ void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 		}
 	}
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_drop_ep_quirk);
 
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -818,7 +812,6 @@ int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return xhci_check_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_check_bandwidth);
 
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -836,4 +829,31 @@ void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	xhci_reset_bandwidth(hcd, udev);
 }
-EXPORT_SYMBOL_GPL(xhci_mtk_reset_bandwidth);
+
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_add_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	if (ep->hcpriv)
+		ret = add_ep_quirk(hcd, udev, ep);
+
+	return ret;
+}
+
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep)
+{
+	int ret;
+
+	ret = xhci_drop_endpoint(hcd, udev, ep);
+	if (ret)
+		return ret;
+
+	drop_ep_quirk(hcd, udev, ep);
+	return 0;
+}
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index fb4e56f6a6c3..57bcfdfa0465 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -417,6 +417,8 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
 
 static const struct xhci_driver_overrides xhci_mtk_overrides __initconst = {
 	.reset = xhci_mtk_setup,
+	.add_endpoint = xhci_mtk_add_ep,
+	.drop_endpoint = xhci_mtk_drop_ep,
 	.check_bandwidth = xhci_mtk_check_bandwidth,
 	.reset_bandwidth = xhci_mtk_reset_bandwidth,
 };
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index d25bf9e49136..621ec1a85009 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -161,38 +161,13 @@ static inline struct xhci_hcd_mtk *hcd_to_mtk(struct usb_hcd *hcd)
 	return dev_get_drvdata(hcd->self.controller);
 }
 
-#if IS_ENABLED(CONFIG_USB_XHCI_MTK)
 int xhci_mtk_sch_init(struct xhci_hcd_mtk *mtk);
 void xhci_mtk_sch_exit(struct xhci_hcd_mtk *mtk);
-int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
-void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep);
+int xhci_mtk_add_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		    struct usb_host_endpoint *ep);
+int xhci_mtk_drop_ep(struct usb_hcd *hcd, struct usb_device *udev,
+		     struct usb_host_endpoint *ep);
 int xhci_mtk_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 
-#else
-static inline int xhci_mtk_add_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_drop_ep_quirk(struct usb_hcd *hcd,
-	struct usb_device *udev, struct usb_host_endpoint *ep)
-{
-}
-
-static inline int xhci_mtk_check_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-	return 0;
-}
-
-static inline void xhci_mtk_reset_bandwidth(struct usb_hcd *hcd,
-		struct usb_device *udev)
-{
-}
-#endif
-
 #endif		/* _XHCI_MTK_H_ */
diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c
index 5e548a1c93ab..c8a880111435 100644
--- a/drivers/usb/host/xhci-ring.c
+++ b/drivers/usb/host/xhci-ring.c
@@ -57,7 +57,6 @@
 #include <linux/dma-mapping.h>
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 
 static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd,
 			 u32 field1, u32 field2,
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index bd27bd670104..13baeda927f0 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -20,7 +20,6 @@
 
 #include "xhci.h"
 #include "xhci-trace.h"
-#include "xhci-mtk.h"
 #include "xhci-debugfs.h"
 #include "xhci-dbgcap.h"
 
@@ -1420,6 +1419,7 @@ unsigned int xhci_get_endpoint_index(struct usb_endpoint_descriptor *desc)
 			(usb_endpoint_dir_in(desc) ? 1 : 0) - 1;
 	return index;
 }
+EXPORT_SYMBOL_GPL(xhci_get_endpoint_index);
 
 /* The reverse operation to xhci_get_endpoint_index. Calculate the USB endpoint
  * address from the XHCI endpoint index.
@@ -1852,8 +1852,8 @@ static int xhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
  * disabled, so there's no need for mutual exclusion to protect
  * the xhci->devs[slot_id] structure.
  */
-static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx, *out_ctx;
@@ -1913,9 +1913,6 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 
 	xhci_endpoint_zero(xhci, xhci->devs[udev->slot_id], ep);
 
-	if (xhci->quirks & XHCI_MTK_HOST)
-		xhci_mtk_drop_ep_quirk(hcd, udev, ep);
-
 	xhci_dbg(xhci, "drop ep 0x%x, slot id %d, new drop flags = %#x, new add flags = %#x\n",
 			(unsigned int) ep->desc.bEndpointAddress,
 			udev->slot_id,
@@ -1923,6 +1920,7 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_drop_endpoint);
 
 /* Add an endpoint to a new possible bandwidth configuration for this device.
  * Only one call to this function is allowed per endpoint before
@@ -1937,8 +1935,8 @@ static int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
  * configuration or alt setting is installed in the device, so there's no need
  * for mutual exclusion to protect the xhci->devs[slot_id] structure.
  */
-static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
-		struct usb_host_endpoint *ep)
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep)
 {
 	struct xhci_hcd *xhci;
 	struct xhci_container_ctx *in_ctx;
@@ -2012,15 +2010,6 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 		return -ENOMEM;
 	}
 
-	if (xhci->quirks & XHCI_MTK_HOST) {
-		ret = xhci_mtk_add_ep_quirk(hcd, udev, ep);
-		if (ret < 0) {
-			xhci_ring_free(xhci, virt_dev->eps[ep_index].new_ring);
-			virt_dev->eps[ep_index].new_ring = NULL;
-			return ret;
-		}
-	}
-
 	ctrl_ctx->add_flags |= cpu_to_le32(added_ctxs);
 	new_add_flags = le32_to_cpu(ctrl_ctx->add_flags);
 
@@ -2045,6 +2034,7 @@ static int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
 			(unsigned int) new_add_flags);
 	return 0;
 }
+EXPORT_SYMBOL_GPL(xhci_add_endpoint);
 
 static void xhci_zero_in_ctx(struct xhci_hcd *xhci, struct xhci_virt_device *virt_dev)
 {
@@ -3078,6 +3068,7 @@ int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 
 	return ret;
 }
+EXPORT_SYMBOL_GPL(xhci_check_bandwidth);
 
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -3102,6 +3093,7 @@ void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev)
 	}
 	xhci_zero_in_ctx(xhci, virt_dev);
 }
+EXPORT_SYMBOL_GPL(xhci_reset_bandwidth);
 
 static void xhci_setup_input_ctx_for_config_ep(struct xhci_hcd *xhci,
 		struct xhci_container_ctx *in_ctx,
@@ -5428,6 +5420,10 @@ void xhci_init_driver(struct hc_driver *drv,
 			drv->reset = over->reset;
 		if (over->start)
 			drv->start = over->start;
+		if (over->add_endpoint)
+			drv->add_endpoint = over->add_endpoint;
+		if (over->drop_endpoint)
+			drv->drop_endpoint = over->drop_endpoint;
 		if (over->check_bandwidth)
 			drv->check_bandwidth = over->check_bandwidth;
 		if (over->reset_bandwidth)
diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h
index d41de5dc0452..5053c1adda1e 100644
--- a/drivers/usb/host/xhci.h
+++ b/drivers/usb/host/xhci.h
@@ -1928,6 +1928,10 @@ struct xhci_driver_overrides {
 	size_t extra_priv_size;
 	int (*reset)(struct usb_hcd *hcd);
 	int (*start)(struct usb_hcd *hcd);
+	int (*add_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			    struct usb_host_endpoint *ep);
+	int (*drop_endpoint)(struct usb_hcd *hcd, struct usb_device *udev,
+			     struct usb_host_endpoint *ep);
 	int (*check_bandwidth)(struct usb_hcd *, struct usb_device *);
 	void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *);
 };
@@ -2080,6 +2084,10 @@ int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks);
 void xhci_shutdown(struct usb_hcd *hcd);
 void xhci_init_driver(struct hc_driver *drv,
 		      const struct xhci_driver_overrides *over);
+int xhci_add_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		      struct usb_host_endpoint *ep);
+int xhci_drop_endpoint(struct usb_hcd *hcd, struct usb_device *udev,
+		       struct usb_host_endpoint *ep);
 int xhci_check_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 void xhci_reset_bandwidth(struct usb_hcd *hcd, struct usb_device *udev);
 int xhci_disable_slot(struct xhci_hcd *xhci, u32 slot_id);
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Chunfeng Yun]

Add a new function to convert bInterval into the time expressed
in 1us unit.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: move kerneldoc next to function's definition suggested by Alan
---
 drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
 drivers/usb/core/devices.c  | 21 ++++---------------
 drivers/usb/core/endpoint.c | 35 ++++---------------------------
 include/linux/usb/ch9.h     |  3 +++
 4 files changed, 52 insertions(+), 48 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index fc21cf2d36f6..675e8a4e683a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -165,6 +165,47 @@ enum usb_dr_mode usb_get_dr_mode(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_dr_mode);
 
+/**
+ * usb_decode_interval - Decode bInterval into the time expressed in 1us unit
+ * @epd: The descriptor of the endpoint
+ * @speed: The speed that the endpoint works as
+ *
+ * Function returns the interval expressed in 1us unit for servicing
+ * endpoint for data transfers.
+ */
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed)
+{
+	unsigned int interval = 0;
+
+	switch (usb_endpoint_type(epd)) {
+	case USB_ENDPOINT_XFER_CONTROL:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH)
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_ISOC:
+		interval = 1 << (epd->bInterval - 1);
+		break;
+	case USB_ENDPOINT_XFER_BULK:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH && usb_endpoint_dir_out(epd))
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_INT:
+		if (speed >= USB_SPEED_HIGH)
+			interval = 1 << (epd->bInterval - 1);
+		else
+			interval = epd->bInterval;
+		break;
+	}
+
+	interval *= (speed >= USB_SPEED_HIGH) ? 125 : 1000;
+
+	return interval;
+}
+EXPORT_SYMBOL_GPL(usb_decode_interval);
+
 #ifdef CONFIG_OF
 /**
  * of_usb_get_dr_mode_by_phy - Get dual role mode for the controller device
diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c
index 1ef2de6e375a..d8b0041de612 100644
--- a/drivers/usb/core/devices.c
+++ b/drivers/usb/core/devices.c
@@ -157,38 +157,25 @@ static char *usb_dump_endpoint_descriptor(int speed, char *start, char *end,
 	switch (usb_endpoint_type(desc)) {
 	case USB_ENDPOINT_XFER_CONTROL:
 		type = "Ctrl";
-		if (speed == USB_SPEED_HIGH)	/* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		dir = 'B';			/* ctrl is bidirectional */
 		break;
 	case USB_ENDPOINT_XFER_ISOC:
 		type = "Isoc";
-		interval = 1 << (desc->bInterval - 1);
 		break;
 	case USB_ENDPOINT_XFER_BULK:
 		type = "Bulk";
-		if (speed == USB_SPEED_HIGH && dir == 'O') /* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		break;
 	case USB_ENDPOINT_XFER_INT:
 		type = "Int.";
-		if (speed == USB_SPEED_HIGH || speed >= USB_SPEED_SUPER)
-			interval = 1 << (desc->bInterval - 1);
-		else
-			interval = desc->bInterval;
 		break;
 	default:	/* "can't happen" */
 		return start;
 	}
-	interval *= (speed == USB_SPEED_HIGH ||
-		     speed >= USB_SPEED_SUPER) ? 125 : 1000;
-	if (interval % 1000)
+
+	interval = usb_decode_interval(desc, speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c
index 903426b6d305..a2530811cf7d 100644
--- a/drivers/usb/core/endpoint.c
+++ b/drivers/usb/core/endpoint.c
@@ -84,40 +84,13 @@ static ssize_t interval_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
 	struct ep_device *ep = to_ep_device(dev);
+	unsigned int interval;
 	char unit;
-	unsigned interval = 0;
-	unsigned in;
 
-	in = (ep->desc->bEndpointAddress & USB_DIR_IN);
-
-	switch (usb_endpoint_type(ep->desc)) {
-	case USB_ENDPOINT_XFER_CONTROL:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_ISOC:
-		interval = 1 << (ep->desc->bInterval - 1);
-		break;
-
-	case USB_ENDPOINT_XFER_BULK:
-		if (ep->udev->speed == USB_SPEED_HIGH && !in)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_INT:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			interval = 1 << (ep->desc->bInterval - 1);
-		else
-			interval = ep->desc->bInterval;
-		break;
-	}
-	interval *= (ep->udev->speed == USB_SPEED_HIGH) ? 125 : 1000;
-	if (interval % 1000)
+	interval = usb_decode_interval(ep->desc, ep->udev->speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index abdd310c77f0..74debc824645 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -90,6 +90,9 @@ extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
  */
 extern const char *usb_state_string(enum usb_device_state state);
 
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed);
+
 #ifdef CONFIG_TRACING
 /**
  * usb_decode_ctrl - Returns human readable representation of control request.
-- 
2.18.0

[PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Chunfeng Yun]

Add a new function to convert bInterval into the time expressed
in 1us unit.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: move kerneldoc next to function's definition suggested by Alan
---
 drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
 drivers/usb/core/devices.c  | 21 ++++---------------
 drivers/usb/core/endpoint.c | 35 ++++---------------------------
 include/linux/usb/ch9.h     |  3 +++
 4 files changed, 52 insertions(+), 48 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index fc21cf2d36f6..675e8a4e683a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -165,6 +165,47 @@ enum usb_dr_mode usb_get_dr_mode(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_dr_mode);
 
+/**
+ * usb_decode_interval - Decode bInterval into the time expressed in 1us unit
+ * @epd: The descriptor of the endpoint
+ * @speed: The speed that the endpoint works as
+ *
+ * Function returns the interval expressed in 1us unit for servicing
+ * endpoint for data transfers.
+ */
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed)
+{
+	unsigned int interval = 0;
+
+	switch (usb_endpoint_type(epd)) {
+	case USB_ENDPOINT_XFER_CONTROL:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH)
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_ISOC:
+		interval = 1 << (epd->bInterval - 1);
+		break;
+	case USB_ENDPOINT_XFER_BULK:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH && usb_endpoint_dir_out(epd))
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_INT:
+		if (speed >= USB_SPEED_HIGH)
+			interval = 1 << (epd->bInterval - 1);
+		else
+			interval = epd->bInterval;
+		break;
+	}
+
+	interval *= (speed >= USB_SPEED_HIGH) ? 125 : 1000;
+
+	return interval;
+}
+EXPORT_SYMBOL_GPL(usb_decode_interval);
+
 #ifdef CONFIG_OF
 /**
  * of_usb_get_dr_mode_by_phy - Get dual role mode for the controller device
diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c
index 1ef2de6e375a..d8b0041de612 100644
--- a/drivers/usb/core/devices.c
+++ b/drivers/usb/core/devices.c
@@ -157,38 +157,25 @@ static char *usb_dump_endpoint_descriptor(int speed, char *start, char *end,
 	switch (usb_endpoint_type(desc)) {
 	case USB_ENDPOINT_XFER_CONTROL:
 		type = "Ctrl";
-		if (speed == USB_SPEED_HIGH)	/* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		dir = 'B';			/* ctrl is bidirectional */
 		break;
 	case USB_ENDPOINT_XFER_ISOC:
 		type = "Isoc";
-		interval = 1 << (desc->bInterval - 1);
 		break;
 	case USB_ENDPOINT_XFER_BULK:
 		type = "Bulk";
-		if (speed == USB_SPEED_HIGH && dir == 'O') /* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		break;
 	case USB_ENDPOINT_XFER_INT:
 		type = "Int.";
-		if (speed == USB_SPEED_HIGH || speed >= USB_SPEED_SUPER)
-			interval = 1 << (desc->bInterval - 1);
-		else
-			interval = desc->bInterval;
 		break;
 	default:	/* "can't happen" */
 		return start;
 	}
-	interval *= (speed == USB_SPEED_HIGH ||
-		     speed >= USB_SPEED_SUPER) ? 125 : 1000;
-	if (interval % 1000)
+
+	interval = usb_decode_interval(desc, speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c
index 903426b6d305..a2530811cf7d 100644
--- a/drivers/usb/core/endpoint.c
+++ b/drivers/usb/core/endpoint.c
@@ -84,40 +84,13 @@ static ssize_t interval_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
 	struct ep_device *ep = to_ep_device(dev);
+	unsigned int interval;
 	char unit;
-	unsigned interval = 0;
-	unsigned in;
 
-	in = (ep->desc->bEndpointAddress & USB_DIR_IN);
-
-	switch (usb_endpoint_type(ep->desc)) {
-	case USB_ENDPOINT_XFER_CONTROL:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_ISOC:
-		interval = 1 << (ep->desc->bInterval - 1);
-		break;
-
-	case USB_ENDPOINT_XFER_BULK:
-		if (ep->udev->speed == USB_SPEED_HIGH && !in)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_INT:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			interval = 1 << (ep->desc->bInterval - 1);
-		else
-			interval = ep->desc->bInterval;
-		break;
-	}
-	interval *= (ep->udev->speed == USB_SPEED_HIGH) ? 125 : 1000;
-	if (interval % 1000)
+	interval = usb_decode_interval(ep->desc, ep->udev->speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index abdd310c77f0..74debc824645 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -90,6 +90,9 @@ extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
  */
 extern const char *usb_state_string(enum usb_device_state state);
 
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed);
+
 #ifdef CONFIG_TRACING
 /**
  * usb_decode_ctrl - Returns human readable representation of control request.
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Chunfeng Yun]

Add a new function to convert bInterval into the time expressed
in 1us unit.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: move kerneldoc next to function's definition suggested by Alan
---
 drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
 drivers/usb/core/devices.c  | 21 ++++---------------
 drivers/usb/core/endpoint.c | 35 ++++---------------------------
 include/linux/usb/ch9.h     |  3 +++
 4 files changed, 52 insertions(+), 48 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index fc21cf2d36f6..675e8a4e683a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -165,6 +165,47 @@ enum usb_dr_mode usb_get_dr_mode(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_dr_mode);
 
+/**
+ * usb_decode_interval - Decode bInterval into the time expressed in 1us unit
+ * @epd: The descriptor of the endpoint
+ * @speed: The speed that the endpoint works as
+ *
+ * Function returns the interval expressed in 1us unit for servicing
+ * endpoint for data transfers.
+ */
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed)
+{
+	unsigned int interval = 0;
+
+	switch (usb_endpoint_type(epd)) {
+	case USB_ENDPOINT_XFER_CONTROL:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH)
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_ISOC:
+		interval = 1 << (epd->bInterval - 1);
+		break;
+	case USB_ENDPOINT_XFER_BULK:
+		/* uframes per NAK */
+		if (speed == USB_SPEED_HIGH && usb_endpoint_dir_out(epd))
+			interval = epd->bInterval;
+		break;
+	case USB_ENDPOINT_XFER_INT:
+		if (speed >= USB_SPEED_HIGH)
+			interval = 1 << (epd->bInterval - 1);
+		else
+			interval = epd->bInterval;
+		break;
+	}
+
+	interval *= (speed >= USB_SPEED_HIGH) ? 125 : 1000;
+
+	return interval;
+}
+EXPORT_SYMBOL_GPL(usb_decode_interval);
+
 #ifdef CONFIG_OF
 /**
  * of_usb_get_dr_mode_by_phy - Get dual role mode for the controller device
diff --git a/drivers/usb/core/devices.c b/drivers/usb/core/devices.c
index 1ef2de6e375a..d8b0041de612 100644
--- a/drivers/usb/core/devices.c
+++ b/drivers/usb/core/devices.c
@@ -157,38 +157,25 @@ static char *usb_dump_endpoint_descriptor(int speed, char *start, char *end,
 	switch (usb_endpoint_type(desc)) {
 	case USB_ENDPOINT_XFER_CONTROL:
 		type = "Ctrl";
-		if (speed == USB_SPEED_HIGH)	/* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		dir = 'B';			/* ctrl is bidirectional */
 		break;
 	case USB_ENDPOINT_XFER_ISOC:
 		type = "Isoc";
-		interval = 1 << (desc->bInterval - 1);
 		break;
 	case USB_ENDPOINT_XFER_BULK:
 		type = "Bulk";
-		if (speed == USB_SPEED_HIGH && dir == 'O') /* uframes per NAK */
-			interval = desc->bInterval;
-		else
-			interval = 0;
 		break;
 	case USB_ENDPOINT_XFER_INT:
 		type = "Int.";
-		if (speed == USB_SPEED_HIGH || speed >= USB_SPEED_SUPER)
-			interval = 1 << (desc->bInterval - 1);
-		else
-			interval = desc->bInterval;
 		break;
 	default:	/* "can't happen" */
 		return start;
 	}
-	interval *= (speed == USB_SPEED_HIGH ||
-		     speed >= USB_SPEED_SUPER) ? 125 : 1000;
-	if (interval % 1000)
+
+	interval = usb_decode_interval(desc, speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c
index 903426b6d305..a2530811cf7d 100644
--- a/drivers/usb/core/endpoint.c
+++ b/drivers/usb/core/endpoint.c
@@ -84,40 +84,13 @@ static ssize_t interval_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
 {
 	struct ep_device *ep = to_ep_device(dev);
+	unsigned int interval;
 	char unit;
-	unsigned interval = 0;
-	unsigned in;
 
-	in = (ep->desc->bEndpointAddress & USB_DIR_IN);
-
-	switch (usb_endpoint_type(ep->desc)) {
-	case USB_ENDPOINT_XFER_CONTROL:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_ISOC:
-		interval = 1 << (ep->desc->bInterval - 1);
-		break;
-
-	case USB_ENDPOINT_XFER_BULK:
-		if (ep->udev->speed == USB_SPEED_HIGH && !in)
-			/* uframes per NAK */
-			interval = ep->desc->bInterval;
-		break;
-
-	case USB_ENDPOINT_XFER_INT:
-		if (ep->udev->speed == USB_SPEED_HIGH)
-			interval = 1 << (ep->desc->bInterval - 1);
-		else
-			interval = ep->desc->bInterval;
-		break;
-	}
-	interval *= (ep->udev->speed == USB_SPEED_HIGH) ? 125 : 1000;
-	if (interval % 1000)
+	interval = usb_decode_interval(ep->desc, ep->udev->speed);
+	if (interval % 1000) {
 		unit = 'u';
-	else {
+	} else {
 		unit = 'm';
 		interval /= 1000;
 	}
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index abdd310c77f0..74debc824645 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -90,6 +90,9 @@ extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
  */
 extern const char *usb_state_string(enum usb_device_state state);
 
+unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
+				 enum usb_device_speed speed);
+
 #ifdef CONFIG_TRACING
 /**
  * usb_decode_ctrl - Returns human readable representation of control request.
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 17/18] usb: xhci-mtk: print debug info of endpoint interval

[Chunfeng Yun]

Print bInterval and convert it into the time expressed in
us or ms unit, this is the key info when allocate bandwidth
failed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++++++++++++-------
 1 file changed, 29 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 046b7f1ebf94..a59d1f6d4744 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,8 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+#define DBG_BUF_EN	64
+
 /* schedule error type */
 #define ESCH_SS_Y6		1001
 #define ESCH_SS_OVERLAP		1002
@@ -62,6 +64,31 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static const char *
+decode_ep(struct usb_host_endpoint *ep, enum usb_device_speed speed)
+{
+	static char buf[DBG_BUF_EN];
+	struct usb_endpoint_descriptor *epd = &ep->desc;
+	unsigned int interval;
+	const char *unit;
+
+	interval = usb_decode_interval(epd, speed);
+	if (interval % 1000) {
+		unit = "us";
+	} else {
+		unit = "ms";
+		interval /= 1000;
+	}
+
+	snprintf(buf, DBG_BUF_EN, "%s ep%d%s %s, mpkt:%d, interval:%d/%d%s\n",
+		 usb_speed_string(speed), usb_endpoint_num(epd),
+		 usb_endpoint_dir_in(epd) ? "in" : "out",
+		 usb_ep_type_string(usb_endpoint_type(epd)),
+		 usb_endpoint_maxp(epd), epd->bInterval, interval, unit);
+
+	return buf;
+}
+
 static u32 get_bw_boundary(enum usb_device_speed speed)
 {
 	u32 boundary;
@@ -711,10 +738,7 @@ static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
@@ -750,10 +774,7 @@ static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	virt_dev = xhci->devs[udev->slot_id];
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
-- 
2.18.0

[PATCH v2 17/18] usb: xhci-mtk: print debug info of endpoint interval

[Chunfeng Yun]

Print bInterval and convert it into the time expressed in
us or ms unit, this is the key info when allocate bandwidth
failed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++++++++++++-------
 1 file changed, 29 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 046b7f1ebf94..a59d1f6d4744 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,8 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+#define DBG_BUF_EN	64
+
 /* schedule error type */
 #define ESCH_SS_Y6		1001
 #define ESCH_SS_OVERLAP		1002
@@ -62,6 +64,31 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static const char *
+decode_ep(struct usb_host_endpoint *ep, enum usb_device_speed speed)
+{
+	static char buf[DBG_BUF_EN];
+	struct usb_endpoint_descriptor *epd = &ep->desc;
+	unsigned int interval;
+	const char *unit;
+
+	interval = usb_decode_interval(epd, speed);
+	if (interval % 1000) {
+		unit = "us";
+	} else {
+		unit = "ms";
+		interval /= 1000;
+	}
+
+	snprintf(buf, DBG_BUF_EN, "%s ep%d%s %s, mpkt:%d, interval:%d/%d%s\n",
+		 usb_speed_string(speed), usb_endpoint_num(epd),
+		 usb_endpoint_dir_in(epd) ? "in" : "out",
+		 usb_ep_type_string(usb_endpoint_type(epd)),
+		 usb_endpoint_maxp(epd), epd->bInterval, interval, unit);
+
+	return buf;
+}
+
 static u32 get_bw_boundary(enum usb_device_speed speed)
 {
 	u32 boundary;
@@ -711,10 +738,7 @@ static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
@@ -750,10 +774,7 @@ static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	virt_dev = xhci->devs[udev->slot_id];
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 17/18] usb: xhci-mtk: print debug info of endpoint interval

[Chunfeng Yun]

Print bInterval and convert it into the time expressed in
us or ms unit, this is the key info when allocate bandwidth
failed.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: no changes
---
 drivers/usb/host/xhci-mtk-sch.c | 37 ++++++++++++++++++++++++++-------
 1 file changed, 29 insertions(+), 8 deletions(-)

diff --git a/drivers/usb/host/xhci-mtk-sch.c b/drivers/usb/host/xhci-mtk-sch.c
index 046b7f1ebf94..a59d1f6d4744 100644
--- a/drivers/usb/host/xhci-mtk-sch.c
+++ b/drivers/usb/host/xhci-mtk-sch.c
@@ -25,6 +25,8 @@
  */
 #define TT_MICROFRAMES_MAX 9
 
+#define DBG_BUF_EN	64
+
 /* schedule error type */
 #define ESCH_SS_Y6		1001
 #define ESCH_SS_OVERLAP		1002
@@ -62,6 +64,31 @@ static int is_fs_or_ls(enum usb_device_speed speed)
 	return speed == USB_SPEED_FULL || speed == USB_SPEED_LOW;
 }
 
+static const char *
+decode_ep(struct usb_host_endpoint *ep, enum usb_device_speed speed)
+{
+	static char buf[DBG_BUF_EN];
+	struct usb_endpoint_descriptor *epd = &ep->desc;
+	unsigned int interval;
+	const char *unit;
+
+	interval = usb_decode_interval(epd, speed);
+	if (interval % 1000) {
+		unit = "us";
+	} else {
+		unit = "ms";
+		interval /= 1000;
+	}
+
+	snprintf(buf, DBG_BUF_EN, "%s ep%d%s %s, mpkt:%d, interval:%d/%d%s\n",
+		 usb_speed_string(speed), usb_endpoint_num(epd),
+		 usb_endpoint_dir_in(epd) ? "in" : "out",
+		 usb_ep_type_string(usb_endpoint_type(epd)),
+		 usb_endpoint_maxp(epd), epd->bInterval, interval, unit);
+
+	return buf;
+}
+
 static u32 get_bw_boundary(enum usb_device_speed speed)
 {
 	u32 boundary;
@@ -711,10 +738,7 @@ static int add_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 	ep_index = xhci_get_endpoint_index(&ep->desc);
 	ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->in_ctx, ep_index);
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpkt:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info)) {
 		/*
@@ -750,10 +774,7 @@ static void drop_ep_quirk(struct usb_hcd *hcd, struct usb_device *udev,
 
 	virt_dev = xhci->devs[udev->slot_id];
 
-	xhci_dbg(xhci, "%s() type:%d, speed:%d, mpks:%d, dir:%d, ep:%p\n",
-		__func__, usb_endpoint_type(&ep->desc), udev->speed,
-		usb_endpoint_maxp(&ep->desc),
-		usb_endpoint_dir_in(&ep->desc), ep);
+	xhci_dbg(xhci, "%s %s\n", __func__, decode_ep(ep, udev->speed));
 
 	if (!need_bw_sch(ep, udev->speed, !!virt_dev->tt_info))
 		return;
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Chunfeng Yun]

Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch
---
 drivers/usb/common/common.c | 35 +++++++++++++++++++++
 drivers/usb/common/debug.c  | 22 +++++++++++--
 include/linux/usb/ch9.h     | 61 -------------------------------------
 3 files changed, 55 insertions(+), 63 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index 675e8a4e683a..347fb3d3894a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -25,6 +25,12 @@ static const char *const ep_type_names[] = {
 	[USB_ENDPOINT_XFER_INT] = "intr",
 };
 
+/**
+ * usb_ep_type_string() - Returns human readable-name of the endpoint type.
+ * @ep_type: The endpoint type to return human-readable name for.  If it's not
+ *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
+ *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
+ */
 const char *usb_ep_type_string(int ep_type)
 {
 	if (ep_type < 0 || ep_type >= ARRAY_SIZE(ep_type_names))
@@ -76,6 +82,12 @@ static const char *const ssp_rate[] = {
 	[USB_SSP_GEN_2x2] = "super-speed-plus-gen2x2",
 };
 
+/**
+ * usb_speed_string() - Returns human readable-name of the speed.
+ * @speed: The speed to return human-readable name for.  If it's not
+ *   any of the speeds defined in usb_device_speed enum, string for
+ *   USB_SPEED_UNKNOWN will be returned.
+ */
 const char *usb_speed_string(enum usb_device_speed speed)
 {
 	if (speed < 0 || speed >= ARRAY_SIZE(speed_names))
@@ -84,6 +96,14 @@ const char *usb_speed_string(enum usb_device_speed speed)
 }
 EXPORT_SYMBOL_GPL(usb_speed_string);
 
+/**
+ * usb_get_maximum_speed - Get maximum requested speed for a given USB
+ * controller.
+ * @dev: Pointer to the given USB controller device
+ *
+ * The function gets the maximum speed string from property "maximum-speed",
+ * and returns the corresponding enum usb_device_speed.
+ */
 enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 {
 	const char *maximum_speed;
@@ -102,6 +122,15 @@ enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_speed);
 
+/**
+ * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
+ *	of a SuperSpeed Plus capable device.
+ * @dev: Pointer to the given USB controller device
+ *
+ * If the string from "maximum-speed" property is super-speed-plus-genXxY where
+ * 'X' is the generation number and 'Y' is the number of lanes, then this
+ * function returns the corresponding enum usb_ssp_rate.
+ */
 enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 {
 	const char *maximum_speed;
@@ -116,6 +145,12 @@ enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_ssp_rate);
 
+/**
+ * usb_state_string - Returns human readable name for the state.
+ * @state: The state to return a human-readable name for. If it's not
+ *	any of the states devices in usb_device_state_string enum,
+ *	the string UNKNOWN will be returned.
+ */
 const char *usb_state_string(enum usb_device_state state)
 {
 	static const char *const names[] = {
diff --git a/drivers/usb/common/debug.c b/drivers/usb/common/debug.c
index ba849c7bc5c7..a76a086b9c54 100644
--- a/drivers/usb/common/debug.c
+++ b/drivers/usb/common/debug.c
@@ -207,8 +207,26 @@ static void usb_decode_set_isoch_delay(__u8 wValue, char *str, size_t size)
 	snprintf(str, size, "Set Isochronous Delay(Delay = %d ns)", wValue);
 }
 
-/*
- * usb_decode_ctrl - returns a string representation of ctrl request
+/**
+ * usb_decode_ctrl - Returns human readable representation of control request.
+ * @str: buffer to return a human-readable representation of control request.
+ *       This buffer should have about 200 bytes.
+ * @size: size of str buffer.
+ * @bRequestType: matches the USB bmRequestType field
+ * @bRequest: matches the USB bRequest field
+ * @wValue: matches the USB wValue field (CPU byte order)
+ * @wIndex: matches the USB wIndex field (CPU byte order)
+ * @wLength: matches the USB wLength field (CPU byte order)
+ *
+ * Function returns decoded, formatted and human-readable description of
+ * control request packet.
+ *
+ * The usage scenario for this is for tracepoints, so function as a return
+ * use the same value as in parameters. This approach allows to use this
+ * function in TP_printk
+ *
+ * Important: wValue, wIndex, wLength parameters before invoking this function
+ * should be processed by le16_to_cpu macro.
  */
 const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 			    __u8 bRequest, __u16 wValue, __u16 wIndex,
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 74debc824645..1cffa34740b0 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -45,76 +45,15 @@ enum usb_ssp_rate {
 	USB_SSP_GEN_2x2,
 };
 
-/**
- * usb_ep_type_string() - Returns human readable-name of the endpoint type.
- * @ep_type: The endpoint type to return human-readable name for.  If it's not
- *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
- *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
- */
 extern const char *usb_ep_type_string(int ep_type);
-
-/**
- * usb_speed_string() - Returns human readable-name of the speed.
- * @speed: The speed to return human-readable name for.  If it's not
- *   any of the speeds defined in usb_device_speed enum, string for
- *   USB_SPEED_UNKNOWN will be returned.
- */
 extern const char *usb_speed_string(enum usb_device_speed speed);
-
-/**
- * usb_get_maximum_speed - Get maximum requested speed for a given USB
- * controller.
- * @dev: Pointer to the given USB controller device
- *
- * The function gets the maximum speed string from property "maximum-speed",
- * and returns the corresponding enum usb_device_speed.
- */
 extern enum usb_device_speed usb_get_maximum_speed(struct device *dev);
-
-/**
- * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
- *	of a SuperSpeed Plus capable device.
- * @dev: Pointer to the given USB controller device
- *
- * If the string from "maximum-speed" property is super-speed-plus-genXxY where
- * 'X' is the generation number and 'Y' is the number of lanes, then this
- * function returns the corresponding enum usb_ssp_rate.
- */
 extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
-
-/**
- * usb_state_string - Returns human readable name for the state.
- * @state: The state to return a human-readable name for. If it's not
- *	any of the states devices in usb_device_state_string enum,
- *	the string UNKNOWN will be returned.
- */
 extern const char *usb_state_string(enum usb_device_state state);
-
 unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
 				 enum usb_device_speed speed);
 
 #ifdef CONFIG_TRACING
-/**
- * usb_decode_ctrl - Returns human readable representation of control request.
- * @str: buffer to return a human-readable representation of control request.
- *       This buffer should have about 200 bytes.
- * @size: size of str buffer.
- * @bRequestType: matches the USB bmRequestType field
- * @bRequest: matches the USB bRequest field
- * @wValue: matches the USB wValue field (CPU byte order)
- * @wIndex: matches the USB wIndex field (CPU byte order)
- * @wLength: matches the USB wLength field (CPU byte order)
- *
- * Function returns decoded, formatted and human-readable description of
- * control request packet.
- *
- * The usage scenario for this is for tracepoints, so function as a return
- * use the same value as in parameters. This approach allows to use this
- * function in TP_printk
- *
- * Important: wValue, wIndex, wLength parameters before invoking this function
- * should be processed by le16_to_cpu macro.
- */
 extern const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 				   __u8 bRequest, __u16 wValue, __u16 wIndex,
 				   __u16 wLength);
-- 
2.18.0

[PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Chunfeng Yun]

Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch
---
 drivers/usb/common/common.c | 35 +++++++++++++++++++++
 drivers/usb/common/debug.c  | 22 +++++++++++--
 include/linux/usb/ch9.h     | 61 -------------------------------------
 3 files changed, 55 insertions(+), 63 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index 675e8a4e683a..347fb3d3894a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -25,6 +25,12 @@ static const char *const ep_type_names[] = {
 	[USB_ENDPOINT_XFER_INT] = "intr",
 };
 
+/**
+ * usb_ep_type_string() - Returns human readable-name of the endpoint type.
+ * @ep_type: The endpoint type to return human-readable name for.  If it's not
+ *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
+ *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
+ */
 const char *usb_ep_type_string(int ep_type)
 {
 	if (ep_type < 0 || ep_type >= ARRAY_SIZE(ep_type_names))
@@ -76,6 +82,12 @@ static const char *const ssp_rate[] = {
 	[USB_SSP_GEN_2x2] = "super-speed-plus-gen2x2",
 };
 
+/**
+ * usb_speed_string() - Returns human readable-name of the speed.
+ * @speed: The speed to return human-readable name for.  If it's not
+ *   any of the speeds defined in usb_device_speed enum, string for
+ *   USB_SPEED_UNKNOWN will be returned.
+ */
 const char *usb_speed_string(enum usb_device_speed speed)
 {
 	if (speed < 0 || speed >= ARRAY_SIZE(speed_names))
@@ -84,6 +96,14 @@ const char *usb_speed_string(enum usb_device_speed speed)
 }
 EXPORT_SYMBOL_GPL(usb_speed_string);
 
+/**
+ * usb_get_maximum_speed - Get maximum requested speed for a given USB
+ * controller.
+ * @dev: Pointer to the given USB controller device
+ *
+ * The function gets the maximum speed string from property "maximum-speed",
+ * and returns the corresponding enum usb_device_speed.
+ */
 enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 {
 	const char *maximum_speed;
@@ -102,6 +122,15 @@ enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_speed);
 
+/**
+ * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
+ *	of a SuperSpeed Plus capable device.
+ * @dev: Pointer to the given USB controller device
+ *
+ * If the string from "maximum-speed" property is super-speed-plus-genXxY where
+ * 'X' is the generation number and 'Y' is the number of lanes, then this
+ * function returns the corresponding enum usb_ssp_rate.
+ */
 enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 {
 	const char *maximum_speed;
@@ -116,6 +145,12 @@ enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_ssp_rate);
 
+/**
+ * usb_state_string - Returns human readable name for the state.
+ * @state: The state to return a human-readable name for. If it's not
+ *	any of the states devices in usb_device_state_string enum,
+ *	the string UNKNOWN will be returned.
+ */
 const char *usb_state_string(enum usb_device_state state)
 {
 	static const char *const names[] = {
diff --git a/drivers/usb/common/debug.c b/drivers/usb/common/debug.c
index ba849c7bc5c7..a76a086b9c54 100644
--- a/drivers/usb/common/debug.c
+++ b/drivers/usb/common/debug.c
@@ -207,8 +207,26 @@ static void usb_decode_set_isoch_delay(__u8 wValue, char *str, size_t size)
 	snprintf(str, size, "Set Isochronous Delay(Delay = %d ns)", wValue);
 }
 
-/*
- * usb_decode_ctrl - returns a string representation of ctrl request
+/**
+ * usb_decode_ctrl - Returns human readable representation of control request.
+ * @str: buffer to return a human-readable representation of control request.
+ *       This buffer should have about 200 bytes.
+ * @size: size of str buffer.
+ * @bRequestType: matches the USB bmRequestType field
+ * @bRequest: matches the USB bRequest field
+ * @wValue: matches the USB wValue field (CPU byte order)
+ * @wIndex: matches the USB wIndex field (CPU byte order)
+ * @wLength: matches the USB wLength field (CPU byte order)
+ *
+ * Function returns decoded, formatted and human-readable description of
+ * control request packet.
+ *
+ * The usage scenario for this is for tracepoints, so function as a return
+ * use the same value as in parameters. This approach allows to use this
+ * function in TP_printk
+ *
+ * Important: wValue, wIndex, wLength parameters before invoking this function
+ * should be processed by le16_to_cpu macro.
  */
 const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 			    __u8 bRequest, __u16 wValue, __u16 wIndex,
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 74debc824645..1cffa34740b0 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -45,76 +45,15 @@ enum usb_ssp_rate {
 	USB_SSP_GEN_2x2,
 };
 
-/**
- * usb_ep_type_string() - Returns human readable-name of the endpoint type.
- * @ep_type: The endpoint type to return human-readable name for.  If it's not
- *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
- *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
- */
 extern const char *usb_ep_type_string(int ep_type);
-
-/**
- * usb_speed_string() - Returns human readable-name of the speed.
- * @speed: The speed to return human-readable name for.  If it's not
- *   any of the speeds defined in usb_device_speed enum, string for
- *   USB_SPEED_UNKNOWN will be returned.
- */
 extern const char *usb_speed_string(enum usb_device_speed speed);
-
-/**
- * usb_get_maximum_speed - Get maximum requested speed for a given USB
- * controller.
- * @dev: Pointer to the given USB controller device
- *
- * The function gets the maximum speed string from property "maximum-speed",
- * and returns the corresponding enum usb_device_speed.
- */
 extern enum usb_device_speed usb_get_maximum_speed(struct device *dev);
-
-/**
- * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
- *	of a SuperSpeed Plus capable device.
- * @dev: Pointer to the given USB controller device
- *
- * If the string from "maximum-speed" property is super-speed-plus-genXxY where
- * 'X' is the generation number and 'Y' is the number of lanes, then this
- * function returns the corresponding enum usb_ssp_rate.
- */
 extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
-
-/**
- * usb_state_string - Returns human readable name for the state.
- * @state: The state to return a human-readable name for. If it's not
- *	any of the states devices in usb_device_state_string enum,
- *	the string UNKNOWN will be returned.
- */
 extern const char *usb_state_string(enum usb_device_state state);
-
 unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
 				 enum usb_device_speed speed);
 
 #ifdef CONFIG_TRACING
-/**
- * usb_decode_ctrl - Returns human readable representation of control request.
- * @str: buffer to return a human-readable representation of control request.
- *       This buffer should have about 200 bytes.
- * @size: size of str buffer.
- * @bRequestType: matches the USB bmRequestType field
- * @bRequest: matches the USB bRequest field
- * @wValue: matches the USB wValue field (CPU byte order)
- * @wIndex: matches the USB wIndex field (CPU byte order)
- * @wLength: matches the USB wLength field (CPU byte order)
- *
- * Function returns decoded, formatted and human-readable description of
- * control request packet.
- *
- * The usage scenario for this is for tracepoints, so function as a return
- * use the same value as in parameters. This approach allows to use this
- * function in TP_printk
- *
- * Important: wValue, wIndex, wLength parameters before invoking this function
- * should be processed by le16_to_cpu macro.
- */
 extern const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 				   __u8 bRequest, __u16 wValue, __u16 wIndex,
 				   __u16 wLength);
-- 
2.18.0
_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Chunfeng Yun]

Following a general rule, add the kerneldoc for a function next
to it's definition, but not next to its declaration in a header
file.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
v2: new patch
---
 drivers/usb/common/common.c | 35 +++++++++++++++++++++
 drivers/usb/common/debug.c  | 22 +++++++++++--
 include/linux/usb/ch9.h     | 61 -------------------------------------
 3 files changed, 55 insertions(+), 63 deletions(-)

diff --git a/drivers/usb/common/common.c b/drivers/usb/common/common.c
index 675e8a4e683a..347fb3d3894a 100644
--- a/drivers/usb/common/common.c
+++ b/drivers/usb/common/common.c
@@ -25,6 +25,12 @@ static const char *const ep_type_names[] = {
 	[USB_ENDPOINT_XFER_INT] = "intr",
 };
 
+/**
+ * usb_ep_type_string() - Returns human readable-name of the endpoint type.
+ * @ep_type: The endpoint type to return human-readable name for.  If it's not
+ *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
+ *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
+ */
 const char *usb_ep_type_string(int ep_type)
 {
 	if (ep_type < 0 || ep_type >= ARRAY_SIZE(ep_type_names))
@@ -76,6 +82,12 @@ static const char *const ssp_rate[] = {
 	[USB_SSP_GEN_2x2] = "super-speed-plus-gen2x2",
 };
 
+/**
+ * usb_speed_string() - Returns human readable-name of the speed.
+ * @speed: The speed to return human-readable name for.  If it's not
+ *   any of the speeds defined in usb_device_speed enum, string for
+ *   USB_SPEED_UNKNOWN will be returned.
+ */
 const char *usb_speed_string(enum usb_device_speed speed)
 {
 	if (speed < 0 || speed >= ARRAY_SIZE(speed_names))
@@ -84,6 +96,14 @@ const char *usb_speed_string(enum usb_device_speed speed)
 }
 EXPORT_SYMBOL_GPL(usb_speed_string);
 
+/**
+ * usb_get_maximum_speed - Get maximum requested speed for a given USB
+ * controller.
+ * @dev: Pointer to the given USB controller device
+ *
+ * The function gets the maximum speed string from property "maximum-speed",
+ * and returns the corresponding enum usb_device_speed.
+ */
 enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 {
 	const char *maximum_speed;
@@ -102,6 +122,15 @@ enum usb_device_speed usb_get_maximum_speed(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_speed);
 
+/**
+ * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
+ *	of a SuperSpeed Plus capable device.
+ * @dev: Pointer to the given USB controller device
+ *
+ * If the string from "maximum-speed" property is super-speed-plus-genXxY where
+ * 'X' is the generation number and 'Y' is the number of lanes, then this
+ * function returns the corresponding enum usb_ssp_rate.
+ */
 enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 {
 	const char *maximum_speed;
@@ -116,6 +145,12 @@ enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev)
 }
 EXPORT_SYMBOL_GPL(usb_get_maximum_ssp_rate);
 
+/**
+ * usb_state_string - Returns human readable name for the state.
+ * @state: The state to return a human-readable name for. If it's not
+ *	any of the states devices in usb_device_state_string enum,
+ *	the string UNKNOWN will be returned.
+ */
 const char *usb_state_string(enum usb_device_state state)
 {
 	static const char *const names[] = {
diff --git a/drivers/usb/common/debug.c b/drivers/usb/common/debug.c
index ba849c7bc5c7..a76a086b9c54 100644
--- a/drivers/usb/common/debug.c
+++ b/drivers/usb/common/debug.c
@@ -207,8 +207,26 @@ static void usb_decode_set_isoch_delay(__u8 wValue, char *str, size_t size)
 	snprintf(str, size, "Set Isochronous Delay(Delay = %d ns)", wValue);
 }
 
-/*
- * usb_decode_ctrl - returns a string representation of ctrl request
+/**
+ * usb_decode_ctrl - Returns human readable representation of control request.
+ * @str: buffer to return a human-readable representation of control request.
+ *       This buffer should have about 200 bytes.
+ * @size: size of str buffer.
+ * @bRequestType: matches the USB bmRequestType field
+ * @bRequest: matches the USB bRequest field
+ * @wValue: matches the USB wValue field (CPU byte order)
+ * @wIndex: matches the USB wIndex field (CPU byte order)
+ * @wLength: matches the USB wLength field (CPU byte order)
+ *
+ * Function returns decoded, formatted and human-readable description of
+ * control request packet.
+ *
+ * The usage scenario for this is for tracepoints, so function as a return
+ * use the same value as in parameters. This approach allows to use this
+ * function in TP_printk
+ *
+ * Important: wValue, wIndex, wLength parameters before invoking this function
+ * should be processed by le16_to_cpu macro.
  */
 const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 			    __u8 bRequest, __u16 wValue, __u16 wIndex,
diff --git a/include/linux/usb/ch9.h b/include/linux/usb/ch9.h
index 74debc824645..1cffa34740b0 100644
--- a/include/linux/usb/ch9.h
+++ b/include/linux/usb/ch9.h
@@ -45,76 +45,15 @@ enum usb_ssp_rate {
 	USB_SSP_GEN_2x2,
 };
 
-/**
- * usb_ep_type_string() - Returns human readable-name of the endpoint type.
- * @ep_type: The endpoint type to return human-readable name for.  If it's not
- *   any of the types: USB_ENDPOINT_XFER_{CONTROL, ISOC, BULK, INT},
- *   usually got by usb_endpoint_type(), the string 'unknown' will be returned.
- */
 extern const char *usb_ep_type_string(int ep_type);
-
-/**
- * usb_speed_string() - Returns human readable-name of the speed.
- * @speed: The speed to return human-readable name for.  If it's not
- *   any of the speeds defined in usb_device_speed enum, string for
- *   USB_SPEED_UNKNOWN will be returned.
- */
 extern const char *usb_speed_string(enum usb_device_speed speed);
-
-/**
- * usb_get_maximum_speed - Get maximum requested speed for a given USB
- * controller.
- * @dev: Pointer to the given USB controller device
- *
- * The function gets the maximum speed string from property "maximum-speed",
- * and returns the corresponding enum usb_device_speed.
- */
 extern enum usb_device_speed usb_get_maximum_speed(struct device *dev);
-
-/**
- * usb_get_maximum_ssp_rate - Get the signaling rate generation and lane count
- *	of a SuperSpeed Plus capable device.
- * @dev: Pointer to the given USB controller device
- *
- * If the string from "maximum-speed" property is super-speed-plus-genXxY where
- * 'X' is the generation number and 'Y' is the number of lanes, then this
- * function returns the corresponding enum usb_ssp_rate.
- */
 extern enum usb_ssp_rate usb_get_maximum_ssp_rate(struct device *dev);
-
-/**
- * usb_state_string - Returns human readable name for the state.
- * @state: The state to return a human-readable name for. If it's not
- *	any of the states devices in usb_device_state_string enum,
- *	the string UNKNOWN will be returned.
- */
 extern const char *usb_state_string(enum usb_device_state state);
-
 unsigned int usb_decode_interval(const struct usb_endpoint_descriptor *epd,
 				 enum usb_device_speed speed);
 
 #ifdef CONFIG_TRACING
-/**
- * usb_decode_ctrl - Returns human readable representation of control request.
- * @str: buffer to return a human-readable representation of control request.
- *       This buffer should have about 200 bytes.
- * @size: size of str buffer.
- * @bRequestType: matches the USB bmRequestType field
- * @bRequest: matches the USB bRequest field
- * @wValue: matches the USB wValue field (CPU byte order)
- * @wIndex: matches the USB wIndex field (CPU byte order)
- * @wLength: matches the USB wLength field (CPU byte order)
- *
- * Function returns decoded, formatted and human-readable description of
- * control request packet.
- *
- * The usage scenario for this is for tracepoints, so function as a return
- * use the same value as in parameters. This approach allows to use this
- * function in TP_printk
- *
- * Important: wValue, wIndex, wLength parameters before invoking this function
- * should be processed by le16_to_cpu macro.
- */
 extern const char *usb_decode_ctrl(char *str, size_t size, __u8 bRequestType,
 				   __u8 bRequest, __u16 wValue, __u16 wIndex,
 				   __u16 wLength);
-- 
2.18.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Mathias Nyman]

On 8.3.2021 4.52, Chunfeng Yun wrote:
> Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
> is not flexible for some cases. For example:
> USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
> implement extended functions if only update xhci-mtk.ko
> This patch is used to remove the dependence.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: no changes
> ---
>  drivers/usb/host/Makefile       |  6 ++---
>  drivers/usb/host/xhci-mem.c     |  2 +-
>  drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
>  drivers/usb/host/xhci-mtk.c     |  2 ++
>  drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
>  drivers/usb/host/xhci-ring.c    |  1 -
>  drivers/usb/host/xhci.c         | 30 +++++++++------------
>  drivers/usb/host/xhci.h         |  8 ++++++
>  8 files changed, 64 insertions(+), 66 deletions(-)
> 

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>

Re: [PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Mathias Nyman]

On 8.3.2021 4.52, Chunfeng Yun wrote:
> Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
> is not flexible for some cases. For example:
> USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
> implement extended functions if only update xhci-mtk.ko
> This patch is used to remove the dependence.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: no changes
> ---
>  drivers/usb/host/Makefile       |  6 ++---
>  drivers/usb/host/xhci-mem.c     |  2 +-
>  drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
>  drivers/usb/host/xhci-mtk.c     |  2 ++
>  drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
>  drivers/usb/host/xhci-ring.c    |  1 -
>  drivers/usb/host/xhci.c         | 30 +++++++++------------
>  drivers/usb/host/xhci.h         |  8 ++++++
>  8 files changed, 64 insertions(+), 66 deletions(-)
> 

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 15/18] usb: xhci-mtk: support to build xhci-mtk-hcd.ko

[Mathias Nyman]

On 8.3.2021 4.52, Chunfeng Yun wrote:
> Currently xhci-hcd.ko building depends on USB_XHCI_MTK, this
> is not flexible for some cases. For example:
> USB_XHCI_HCD is y, and USB_XHCI_MTK is m, then we can't
> implement extended functions if only update xhci-mtk.ko
> This patch is used to remove the dependence.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: no changes
> ---
>  drivers/usb/host/Makefile       |  6 ++---
>  drivers/usb/host/xhci-mem.c     |  2 +-
>  drivers/usb/host/xhci-mtk-sch.c | 48 +++++++++++++++++++++++----------
>  drivers/usb/host/xhci-mtk.c     |  2 ++
>  drivers/usb/host/xhci-mtk.h     | 33 +++--------------------
>  drivers/usb/host/xhci-ring.c    |  1 -
>  drivers/usb/host/xhci.c         | 30 +++++++++------------
>  drivers/usb/host/xhci.h         |  8 ++++++
>  8 files changed, 64 insertions(+), 66 deletions(-)
> 

Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Greg Kroah-Hartman]

On Mon, Mar 08, 2021 at 10:52:07AM +0800, Chunfeng Yun wrote:
> Following a general rule, add the kerneldoc for a function next
> to it's definition, but not next to its declaration in a header
> file.
> 
> Suggested-by: Alan Stern <stern@rowland.harvard.edu>
> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: new patch

Thanks for this change, looks great, all now queued up!

greg k-h

Re: [PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Greg Kroah-Hartman]

On Mon, Mar 08, 2021 at 10:52:07AM +0800, Chunfeng Yun wrote:
> Following a general rule, add the kerneldoc for a function next
> to it's definition, but not next to its declaration in a header
> file.
> 
> Suggested-by: Alan Stern <stern@rowland.harvard.edu>
> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: new patch

Thanks for this change, looks great, all now queued up!

greg k-h

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 18/18] usb: common: move function's kerneldoc next to its definition

[Greg Kroah-Hartman]

On Mon, Mar 08, 2021 at 10:52:07AM +0800, Chunfeng Yun wrote:
> Following a general rule, add the kerneldoc for a function next
> to it's definition, but not next to its declaration in a header
> file.
> 
> Suggested-by: Alan Stern <stern@rowland.harvard.edu>
> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: new patch

Thanks for this change, looks great, all now queued up!

greg k-h

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Alan Stern]

On Mon, Mar 08, 2021 at 10:52:05AM +0800, Chunfeng Yun wrote:
> Add a new function to convert bInterval into the time expressed
> in 1us unit.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: move kerneldoc next to function's definition suggested by Alan
> ---
>  drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
>  drivers/usb/core/devices.c  | 21 ++++---------------
>  drivers/usb/core/endpoint.c | 35 ++++---------------------------
>  include/linux/usb/ch9.h     |  3 +++
>  4 files changed, 52 insertions(+), 48 deletions(-)

Acked-by: Alan Stern <stern@rowland.harvard.edu>

Re: [PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Alan Stern]

On Mon, Mar 08, 2021 at 10:52:05AM +0800, Chunfeng Yun wrote:
> Add a new function to convert bInterval into the time expressed
> in 1us unit.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: move kerneldoc next to function's definition suggested by Alan
> ---
>  drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
>  drivers/usb/core/devices.c  | 21 ++++---------------
>  drivers/usb/core/endpoint.c | 35 ++++---------------------------
>  include/linux/usb/ch9.h     |  3 +++
>  4 files changed, 52 insertions(+), 48 deletions(-)

Acked-by: Alan Stern <stern@rowland.harvard.edu>

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v2 16/18] usb: common: add function to get interval expressed in us unit

[Alan Stern]

On Mon, Mar 08, 2021 at 10:52:05AM +0800, Chunfeng Yun wrote:
> Add a new function to convert bInterval into the time expressed
> in 1us unit.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> ---
> v2: move kerneldoc next to function's definition suggested by Alan
> ---
>  drivers/usb/common/common.c | 41 +++++++++++++++++++++++++++++++++++++
>  drivers/usb/core/devices.c  | 21 ++++---------------
>  drivers/usb/core/endpoint.c | 35 ++++---------------------------
>  include/linux/usb/ch9.h     |  3 +++
>  4 files changed, 52 insertions(+), 48 deletions(-)

Acked-by: Alan Stern <stern@rowland.harvard.edu>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel