[U-Boot] [PATCH v5 02/18] rockchip: boot0: align to 0x20 for armv7 '_start'

[Dr. Philipp Tomsich <philipp.tomsich@theobroma-systems.com>]

Andy,

On 9 Nov 2017, at 13:59, Andy Yan <andy.yan@rock-chips.com> wrote:
> 
> Hi Phipipp, Kever:
> 
> 
> On 2017年10月10日 22:21, Philipp Tomsich wrote:
>> From: Kever Yang <kever.yang@rock-chips.com>
>> 
>> The '_start' is using as vector table base address, and will write
>> to VBAR register, so it needs to be aligned to 0x20 for armv7.
>> 
>> Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
>> [Updated to current code base:]
>> Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
>> 
>> ---
>> 
>> Changes in v5: None
>> Changes in v4: None
>> Changes in v3: None
>> Changes in v2: None
>> 
>>  arch/arm/include/asm/arch-rockchip/boot0.h | 14 ++++++++++++--
>>  1 file changed, 12 insertions(+), 2 deletions(-)
>> 
>> diff --git a/arch/arm/include/asm/arch-rockchip/boot0.h b/arch/arm/include/asm/arch-rockchip/boot0.h
>> index 455d842..f7c6146 100644
>> --- a/arch/arm/include/asm/arch-rockchip/boot0.h
>> +++ b/arch/arm/include/asm/arch-rockchip/boot0.h
>> @@ -6,12 +6,13 @@
>>    /*
>>   * Execution starts on the instruction following this 4-byte header
>> - * (containing the magic 'RK33').
>> + * (containing the magic 'RK30', 'RK31', 'RK32' or 'RK33').  This
>> + * magic constant will be written into the final image by the rkimage
>> + * tool, but we need to reserve space for it here.
>>   *
>>   * To make life easier for everyone, we build the SPL binary with
>>   * space for this 4-byte header already included in the binary.
>>   */
>> -
>>  #ifdef CONFIG_SPL_BUILD
>>  	/*
>>  	 * We need to add 4 bytes of space for the 'RK33' at the
>> @@ -26,6 +27,15 @@
>>  	b reset	 /* may be overwritten --- should be 'nop' or a 'b reset' */
>>  #endif
>>  	b reset
> 
>     Do we really need the "b reset" here? the macro ARM_VECTORS already has a b reset.
> Besides Joseph found  that the irq function will not work with this "b reset”

The quoted code was from an older version of the series, but the ‘b reset’ is still there
in the newer version.

What IRQ function does not work?
Shouldn't the IRQ be jumping into the ARM_VECTORS and never see the ‘b reset’?

>> +#if !defined(CONFIG_ARM64)
>> +	/*
>> +	 * For armv7, the addr '_start' will used as vector start address
>> +	 * and write to VBAR register, which needs to aligned to 0x20.
>> +	 */
>> +	.align(5)
>> +_start:
>> +	ARM_VECTORS
>> +#endif
>>    #if defined(CONFIG_ROCKCHIP_RK3399) && defined(CONFIG_SPL_BUILD)
>>  	.space CONFIG_ROCKCHIP_SPL_RESERVE_IRAM	/* space for the ATF data */
> 
>