[PATCH 56/57] docs: phy: convert samsung-usb2.txt to ReST format

[Mauro Carvalho Chehab <mchehab+samsung@kernel.org>]

In order to merge it into a Sphinx book, we need first to
convert to ReST.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
---
 Documentation/phy/samsung-usb2.txt | 60 +++++++++++++++---------------
 1 file changed, 31 insertions(+), 29 deletions(-)

diff --git a/Documentation/phy/samsung-usb2.txt b/Documentation/phy/samsung-usb2.txt
index ed12d437189d..c48c8b9797b9 100644
--- a/Documentation/phy/samsung-usb2.txt
+++ b/Documentation/phy/samsung-usb2.txt
@@ -1,9 +1,9 @@
-.------------------------------------------------------------------------------+
-|			Samsung USB 2.0 PHY adaptation layer		       |
-+-----------------------------------------------------------------------------+'
+====================================
+Samsung USB 2.0 PHY adaptation layer
+====================================
 
-| 1. Description
-+----------------
+1. Description
+--------------
 
 The architecture of the USB 2.0 PHY module in Samsung SoCs is similar
 among many SoCs. In spite of the similarities it proved difficult to
@@ -14,8 +14,8 @@ the PHY powering up process had to be altered. This adaptation layer is
 a compromise between having separate drivers and having a single driver
 with added support for many special cases.
 
-| 2. Files description
-+----------------------
+2. Files description
+--------------------
 
 - phy-samsung-usb2.c
    This is the main file of the adaptation layer. This file contains
@@ -32,44 +32,45 @@ with added support for many special cases.
    driver. In addition it should contain extern declarations for
    structures that describe particular SoCs.
 
-| 3. Supporting SoCs
-+--------------------
+3. Supporting SoCs
+------------------
 
 To support a new SoC a new file should be added to the drivers/phy
 directory. Each SoC's configuration is stored in an instance of the
-struct samsung_usb2_phy_config.
+struct samsung_usb2_phy_config::
 
-struct samsung_usb2_phy_config {
+  struct samsung_usb2_phy_config {
 	const struct samsung_usb2_common_phy *phys;
 	int (*rate_to_clk)(unsigned long, u32 *);
 	unsigned int num_phys;
 	bool has_mode_switch;
-};
+  };
 
-The num_phys is the number of phys handled by the driver. *phys is an
+The num_phys is the number of phys handled by the driver. `*phys` is an
 array that contains the configuration for each phy. The has_mode_switch
 property is a boolean flag that determines whether the SoC has USB host
 and device on a single pair of pins. If so, a special register has to
 be modified to change the internal routing of these pins between a USB
 device or host module.
 
-For example the configuration for Exynos 4210 is following:
+For example the configuration for Exynos 4210 is following::
 
-const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = {
+  const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = {
 	.has_mode_switch        = 0,
 	.num_phys		= EXYNOS4210_NUM_PHYS,
 	.phys			= exynos4210_phys,
 	.rate_to_clk		= exynos4210_rate_to_clk,
-}
+  }
+
+- `int (*rate_to_clk)(unsigned long, u32 *)`
 
-- int (*rate_to_clk)(unsigned long, u32 *)
 	The rate_to_clk callback is to convert the rate of the clock
 	used as the reference clock for the PHY module to the value
 	that should be written in the hardware register.
 
-The exynos4210_phys configuration array is as follows:
+The exynos4210_phys configuration array is as follows::
 
-static const struct samsung_usb2_common_phy exynos4210_phys[] = {
+  static const struct samsung_usb2_common_phy exynos4210_phys[] = {
 	{
 		.label		= "device",
 		.id		= EXYNOS4210_DEVICE,
@@ -95,29 +96,30 @@ static const struct samsung_usb2_common_phy exynos4210_phys[] = {
 		.power_off	= exynos4210_power_off,
 	},
 	{},
-};
+  };
+
+- `int (*power_on)(struct samsung_usb2_phy_instance *);`
+  `int (*power_off)(struct samsung_usb2_phy_instance *);`
 
-- int (*power_on)(struct samsung_usb2_phy_instance *);
-- int (*power_off)(struct samsung_usb2_phy_instance *);
 	These two callbacks are used to power on and power off the phy
 	by modifying appropriate registers.
 
 Final change to the driver is adding appropriate compatible value to the
 phy-samsung-usb2.c file. In case of Exynos 4210 the following lines were
-added to the struct of_device_id samsung_usb2_phy_of_match[] array:
+added to the struct of_device_id samsung_usb2_phy_of_match[] array::
 
-#ifdef CONFIG_PHY_EXYNOS4210_USB2
+  #ifdef CONFIG_PHY_EXYNOS4210_USB2
 	{
 		.compatible = "samsung,exynos4210-usb2-phy",
 		.data = &exynos4210_usb2_phy_config,
 	},
-#endif
+  #endif
 
 To add further flexibility to the driver the Kconfig file enables to
 include support for selected SoCs in the compiled driver. The Kconfig
-entry for Exynos 4210 is following:
+entry for Exynos 4210 is following::
 
-config PHY_EXYNOS4210_USB2
+  config PHY_EXYNOS4210_USB2
 	bool "Support for Exynos 4210"
 	depends on PHY_SAMSUNG_USB2
 	depends on CPU_EXYNOS4210
@@ -128,8 +130,8 @@ config PHY_EXYNOS4210_USB2
 	  phys are available - device, host, HSCI0 and HSCI1.
 
 The newly created file that supports the new SoC has to be also added to the
-Makefile. In case of Exynos 4210 the added line is following:
+Makefile. In case of Exynos 4210 the added line is following::
 
-obj-$(CONFIG_PHY_EXYNOS4210_USB2)       += phy-exynos4210-usb2.o
+  obj-$(CONFIG_PHY_EXYNOS4210_USB2)       += phy-exynos4210-usb2.o
 
 After completing these steps the support for the new SoC should be ready.
-- 
2.20.1