From mboxrd@z Thu Jan 1 00:00:00 1970 From: Akshay Bhat Subject: Re: [PATCH v2 2/2] can: spi: hi311x: Add Holt HI-311x CAN driver Date: Tue, 14 Mar 2017 12:20:39 -0400 Message-ID: <3dbf8748-9d04-0f21-0e95-448d7a72e7d5@timesys.com> References: <1484680922-25813-1-git-send-email-akshay.bhat@timesys.com> <1484680922-25813-2-git-send-email-akshay.bhat@timesys.com> <234d9e75-0083-b8b4-c781-add653fdb550@grandegger.com> Mime-Version: 1.0 Content-Type: text/plain; charset=utf-8 Content-Transfer-Encoding: 8bit Return-path: Received: from mail-qk0-f179.google.com ([209.85.220.179]:34610 "EHLO mail-qk0-f179.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1750992AbdCNQUn (ORCPT ); Tue, 14 Mar 2017 12:20:43 -0400 Received: by mail-qk0-f179.google.com with SMTP id p64so252048095qke.1 for ; Tue, 14 Mar 2017 09:20:42 -0700 (PDT) In-Reply-To: Sender: linux-can-owner@vger.kernel.org List-ID: To: Wolfgang Grandegger , mkl@pengutronix.de Cc: linux-can@vger.kernel.org, netdev@vger.kernel.org, devicetree@vger.kernel.org, linux-kernel@vger.kernel.org, Akshay Bhat Hi Wolfgang, On 03/14/2017 08:11 AM, Wolfgang Grandegger wrote: > ... snip ... >>> A few other things to check: >>> >>> Run "cangen" and monitor the message with "candump -e any,0:0,#FFFFFFF". >>> Then 1) disconnect the cable or 2) short-circuit CAN low and high at the >>> connector. You should see error messages. After reconnection or removing >>> the short-circuit (and bus-off recovery) the state should go back to >>> "active". >>> >> >> With the above sequence, candump reports "ERRORFRAME" with >> protocol-violation{{}{acknowledge-slot}}, bus-error. On re-connecting >> the cable the can state goes back to ACTIVE and I see the messages that >> were in the queue being sent. > > Do you get the ACK error also with berr-reporting off? Would be nice if > you could show a candump log here. > Below is a log for disconnecting and re-connecting CAN cable scenario: (Note this is on a 4.1.18 kernel with RT patch) root@imx6qrom5420b1:~# ip link set can0 up type can bitrate 1000000 berr-reporting on root@imx6qrom5420b1:~# candump -e any,0:0,#FFFFFFF & [1] 768 root@imx6qrom5420b1:~# cangen can0 can0 21C [8] 35 98 C0 7A 95 03 E6 2A can0 6E6 [1] F2 can0 5C7 [2] 42 50 can0 57C [8] 83 7A E4 0C 03 8B 90 45 can0 55C [8] B9 74 87 52 D8 F4 64 04 can0 014 [8] 28 CB 96 57 3B 80 67 4F can0 6AF [1] 35 can0 51E [8] B6 C8 6C 1D 3A 87 ED 2E can0 527 [8] D0 8A D3 59 0E 34 40 78 can0 30C [2] 6A 12 can0 145 [8] CB 6E FF 55 C1 BE C3 22 can0 5A5 [8] C4 49 54 68 02 63 F9 35 can0 0BA [8] DA 57 5E 3A CE 88 20 1C can0 516 [2] 09 09 can0 743 [8] 7C 4D 25 47 61 4C 56 3D can0 31D [2] 9C D3 can0 71E [8] 53 7C 97 2A 2A F2 9F 56 can0 52E [8] FE DA 2D 51 73 96 DF 79 /////disconnect cable can0 20000088 [8] 00 00 00 19 00 00 28 00 ERRORFRAME protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{40}{0}} can0 20000088 [8] 00 00 00 19 00 00 58 00 ERRORFRAME protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{88}{0}} can0 20000088 [8] 00 00 00 19 00 00 80 00 ERRORFRAME protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{128}{0}} can0 2000008C [8] 00 20 00 19 00 00 80 00 ERRORFRAME controller-problem{tx-error-passive} protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{128}{0}} write: No buffer space available root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 6 0 1 1 0 RX: bytes packets errors dropped overrun mcast 0 0 6 0 0 0 TX: bytes packets errors dropped carrier collsns 106 18 0 0 0 0 root@imx6qrom5420b1:~# /////re-connect cable can0 169 [8] 35 55 A3 1C 0F 47 2E 5B can0 318 [8] 11 AA 27 11 D2 1B CE 34 can0 577 [8] A0 A4 EE 50 8D A2 E1 3E can0 4ED [8] 52 96 17 7E 31 FC 7D 7C can0 2E7 [8] 92 48 D4 39 05 1E 9F 50 can0 200 [8] 4A 66 F6 02 1E 71 8E 26 can0 29A [8] 49 63 2E 7D C9 77 85 7A can0 15A [7] 3C 0E 65 74 C3 62 80 can0 011 [1] D2 can0 26B [3] FC D6 68 can0 5CE [8] 6F 02 B5 14 BC 7A D7 02 root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-ACTIVE (berr-counter tx 117 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 7 0 1 1 0 RX: bytes packets errors dropped overrun mcast 0 0 7 0 0 0 TX: bytes packets errors dropped carrier collsns 181 29 0 0 0 0 //Reboot the board and test with bus error reporting off root@imx6qrom5420b1:~# ip link set can0 up type can bitrate 1000000 berr-reporting off root@imx6qrom5420b1:~# candump -e any,0:0,#FFFFFFF & [1] 782 root@imx6qrom5420b1:~# cangen can0 can0 1FA [3] C9 FE C2 can0 3E2 [5] 85 37 03 5B 6F can0 289 [8] A4 F6 BF 4A 3F 70 65 1B can0 12D [8] B2 72 10 33 AB B4 68 64 can0 054 [2] 01 D7 can0 4A6 [8] 29 7D 76 56 CA C1 60 00 can0 768 [8] 97 3D 92 08 61 C1 D9 03 can0 098 [6] A4 A8 5A 60 92 1A can0 3C9 [8] 71 78 0D 25 AB 27 8B 51 /////disconnect cable write: No buffer space available root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-ACTIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 0 0 0 0 0 RX: bytes packets errors dropped overrun mcast 0 0 0 0 0 0 TX: bytes packets errors dropped carrier collsns 56 9 0 0 0 0 root@imx6qrom5420b1:~# /////re-connect cable can0 20000088 [8] 00 00 00 19 00 00 7F 00 ERRORFRAME protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{127}{0}} can0 553 [6] 1A E4 60 6B DC 07 can0 7E3 [8] 1C 78 95 6E 10 81 AA 40 can0 20C [8] BB 35 13 25 60 0A 56 57 can0 1D0 [8] 48 4A 39 64 76 E6 57 08 can0 43A [1] 40 can0 2CF [7] 03 45 5E 0F 67 33 4C can0 1CD [8] F9 4D AB 1D 96 A5 67 0E can0 515 [8] 41 CD F2 5F 68 92 43 16 can0 661 [8] 45 9A 73 69 45 EE 8B 42 can0 41B [1] 55 can0 52F [1] 87 root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-ACTIVE (berr-counter tx 117 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 1 0 0 0 0 RX: bytes packets errors dropped overrun mcast 0 0 1 0 0 0 TX: bytes packets errors dropped carrier collsns 120 20 0 0 0 0 > Also, any error message should show the bus error counts in data[7,8]: > > http://lxr.free-electrons.com/source/drivers/net/can/sja1000/sja1000.c#L408 > I can add this in v4 version of the patch (Above log has this patch applied). > And please check bus-off as well (short-circuiting CAN low and high). > I have not been able to check the bus-off condition by (short-circuiting CAN low and high). The tec error count remains at 128 when I short the CAN low and high pins and the status never goes BUSOFF. If I short the CAN high pin to ground, then the TEC goes to 136 but thats the highest I have been able to get the TEC to go. The setup I have is: HI-3111 can chip -> ADM3054 can transceiver //CAN_H and CAN_L shorted can0 2000008C [8] 00 20 00 19 00 00 80 00 ERRORFRAME controller-problem{tx-error-passive} protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{128}{0}} root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-PASSIVE (berr-counter tx 128 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 7 0 1 1 0 RX: bytes packets errors dropped overrun mcast 0 0 7 0 0 0 TX: bytes packets errors dropped carrier collsns 626 109 0 0 0 0 //CAN_H shorted to GND can0 2000008C [8] 00 20 00 19 00 00 80 00 ERRORFRAME controller-problem{tx-error-passive} protocol-violation{{}{acknowledge-slot}} bus-error error-counter-tx-rx{{128}{0}} can0 2000008C [8] 00 20 01 00 00 00 88 00 ERRORFRAME controller-problem{tx-error-passive} protocol-violation{{single-bit-error}{}} bus-error error-counter-tx-rx{{136}{0}} root@imx6qrom5420b1:~# ip -s -d link show can0 4: can0: mtu 16 qdisc pfifo_fast state UNKNOWN mode DEFAULT group default qlen 10 link/can promiscuity 0 can state ERROR-PASSIVE (berr-counter tx 136 rx 0) restart-ms 0 bitrate 1000000 sample-point 0.750 tq 62 prop-seg 5 phase-seg1 6 phase-seg2 4 sjw 1 hi3110: tseg1 2..16 tseg2 2..8 sjw 1..4 brp 1..64 brp-inc 1 clock 16000000 re-started bus-errors arbit-lost error-warn error-pass bus-off 0 9 0 1 1 0 RX: bytes packets errors dropped overrun mcast 0 0 9 0 0 0 TX: bytes packets errors dropped carrier collsns 626 109 0 0 0 0 Thanks, Akshay