All of lore.kernel.org
 help / color / mirror / Atom feed
From: Laszlo Ersek <lersek@redhat.com>
To: Ard Biesheuvel <ardb@kernel.org>, linux-efi@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org, leif@nuviainc.com,
	pjones@redhat.com, mjg59@google.com, agraf@csgraf.de,
	ilias.apalodimas@linaro.org, xypron.glpk@gmx.de,
	daniel.kiper@oracle.com
Subject: Re: [PATCH 1/2] efi/libstub: add support for loading the initrd from a device path
Date: Fri, 7 Feb 2020 10:48:30 +0100	[thread overview]
Message-ID: <43362e18-eddc-9903-0e63-9d3eebe70313@redhat.com> (raw)
In-Reply-To: <20200206140352.6300-2-ardb@kernel.org>

On 02/06/20 15:03, Ard Biesheuvel wrote:
> There are currently two ways to specify the initrd to be passed to the
> Linux kernel when booting via the EFI stub:
> - it can be passed as a initrd= command line option when doing a pure PE
>   boot (as opposed to the EFI handover protocol that exists for x86)
> - otherwise, the bootloader or firmware can load the initrd into memory,
>   and pass the address and size via the bootparams struct (x86) or
>   device tree (ARM)
> 
> In the first case, we are limited to loading from the same file system
> that the kernel was loaded from, and it is also problematic in a trusted
> boot context, given that we cannot easily protect the command line from
> tampering without either adding complicated white/blacklisting of boot
> arguments or locking down the command line altogether.
> 
> In the second case, we force the bootloader to duplicate knowledge about
> the boot protocol which is already encoded in the stub, and which may be
> subject to change over time, e.g., bootparams struct definitions, memory
> allocation/alignment requirements for the placement of the initrd etc etc.
> In the ARM case, it also requires the bootloader to modify the hardware
> description provided by the firmware, as it is passed in the same file.
> On systems where the initrd is measured after loading, it creates a time
> window where the initrd contents might be manipulated in memory before
> handing over to the kernel.
> 
> Address these concerns by adding support for loading the initrd into
> memory by invoking the EFI LoadFile2 protocol installed on a vendor
> GUIDed device path that specifically designates a Linux initrd.
> This addresses the above concerns, by putting the EFI stub in charge of
> placement in memory and of passing the base and size to the kernel proper
> (via whatever means it desires) while still leaving it up to the firmware
> or bootloader to obtain the file contents, potentially from other file
> systems than the one the kernel itself was loaded from. On platforms that
> implement measured boot, it permits the firmware to take the measurement
> right before the kernel actually consumes the contents.
> 
> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
> ---
>  drivers/firmware/efi/libstub/arm-stub.c        | 16 +++--
>  drivers/firmware/efi/libstub/efi-stub-helper.c | 65 ++++++++++++++++++++
>  drivers/firmware/efi/libstub/efistub.h         | 12 ++++
>  drivers/firmware/efi/libstub/x86-stub.c        | 36 ++++++++++-
>  include/linux/efi.h                            |  1 +
>  5 files changed, 123 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/firmware/efi/libstub/arm-stub.c b/drivers/firmware/efi/libstub/arm-stub.c
> index c7b091f50e55..1db943c1ba2b 100644
> --- a/drivers/firmware/efi/libstub/arm-stub.c
> +++ b/drivers/firmware/efi/libstub/arm-stub.c
> @@ -157,6 +157,7 @@ unsigned long efi_entry(void *handle, efi_system_table_t *sys_table_arg,
>  	enum efi_secureboot_mode secure_boot;
>  	struct screen_info *si;
>  	efi_properties_table_t *prop_tbl;
> +	unsigned long max_addr;
>  
>  	sys_table = sys_table_arg;
>  
> @@ -255,11 +256,18 @@ unsigned long efi_entry(void *handle, efi_system_table_t *sys_table_arg,
>  	if (!fdt_addr)
>  		pr_efi("Generating empty DTB\n");
>  
> -	status = efi_load_initrd(image, ULONG_MAX,
> -				 efi_get_max_initrd_addr(dram_base, *image_addr),
> -				 &initrd_addr, &initrd_size);
> +	max_addr = efi_get_max_initrd_addr(dram_base, *image_addr);
> +	status = efi_load_initrd_devpath(&initrd_addr, &initrd_size, max_addr);
> +	if (status == EFI_SUCCESS)
> +		pr_efi("Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path\n");
> +	else if (status == EFI_NOT_FOUND) {
> +		status = efi_load_initrd(image, ULONG_MAX, max_addr,
> +					 &initrd_addr, &initrd_size);

- So this seems to be fallback#1, for ARM, which looks good.

- Are you sure you only want to fall back to the old method on
EFI_NOT_FOUND? Wouldn't other return values from
efi_load_initrd_devpath() justify that too?

... After checking the boot services called in
efi_load_initrd_devpath(), this idea seems reasonable, but then I'd
suggest documenting the significance of returning EFI_NOT_FOUND near the
efi_load_initrd_devpath() function declaration, in "efistub.h".

> +		if (status == EFI_SUCCESS)
> +			pr_efi("Loaded initrd from command line option\n");
> +	}
>  	if (status != EFI_SUCCESS)
> -		pr_efi_err("Failed initrd from command line!\n");
> +		pr_efi_err("Failed to load initrd!\n");
>  
>  	efi_random_get_seed();
>  
> diff --git a/drivers/firmware/efi/libstub/efi-stub-helper.c b/drivers/firmware/efi/libstub/efi-stub-helper.c
> index 8e60a39df3c5..eaf45ea749b3 100644
> --- a/drivers/firmware/efi/libstub/efi-stub-helper.c
> +++ b/drivers/firmware/efi/libstub/efi-stub-helper.c
> @@ -323,3 +323,68 @@ void efi_char16_printk(efi_char16_t *str)
>  	efi_call_proto(efi_table_attr(efi_system_table(), con_out),
>  		       output_string, str);
>  }
> +
> +static const struct {
> +	struct efi_vendor_dev_path	vendor;
> +	struct efi_generic_dev_path	end;
> +} __packed initrd_devpath = {
> +	{
> +		EFI_DEV_MEDIA,
> +		EFI_DEV_MEDIA_VENDOR,
> +		sizeof(struct efi_vendor_dev_path),
> +		LINUX_EFI_INITRD_MEDIA_GUID
> +	}, {
> +		EFI_DEV_END_PATH,
> +		EFI_DEV_END_ENTIRE,
> +		sizeof(struct efi_generic_dev_path)
> +	}
> +};
> +
> +efi_status_t efi_load_initrd_devpath(unsigned long *load_addr,
> +				     unsigned long *load_size,
> +				     unsigned long max)
> +{
> +	efi_guid_t lf2_proto_guid = EFI_LOAD_FILE2_PROTOCOL_GUID;
> +	efi_device_path_protocol_t *dp;
> +	efi_load_file2_protocol_t *lf2;
> +	unsigned long initrd_addr;
> +	unsigned long initrd_size;
> +	efi_handle_t handle;
> +	efi_status_t status;
> +
> +	if (!load_addr || !load_size)
> +		return EFI_INVALID_PARAMETER;
> +
> +	dp = (efi_device_path_protocol_t *)&initrd_devpath;
> +	status = efi_bs_call(locate_device_path, &lf2_proto_guid, &dp, &handle);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	status = efi_bs_call(handle_protocol, handle, &lf2_proto_guid,
> +			     (void **)&lf2);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	initrd_size = 0;
> +	status = efi_call_proto(lf2, load_file,
> +				(efi_device_path_protocol_t *)&initrd_devpath,
> +				false, &initrd_size, NULL);

The second argument to EFI_LOAD_FILE2_PROTOCOL.LoadFile() is "FilePath",
specified as "The device specific path of the file to load". This means
it is supposed to be a (possibly empty) sequence of FILEPATH_DEVICE_PATH
nodes, terminated by and "End Entire Device Path" node. See

- 10.3.1 Generic Device Path Structures
- 10.3.5.4 File Path Media Device Path

in UEFI-2.8.

And "initrd_devpath" is not a device path like that; instead it's the
VenMedia device path that's installed on the handle that also carries
our LoadFile2 instance.

Now, I do see that this all theoretical here, as we don't expect the
LoadFile2 instance that we've found via our special
LINUX_EFI_INITRD_MEDIA_GUID VenMedia devpath to do *any* device-specific
filename / pathname parsing.

But in that case (i.e., given that the FilePath argument is totally
irrelevant), I think it's much clearer if we simply pass an empty device
path -- one that consists of a single "End Entire Device Path" node.

I've checked, and your ArmVirtQemu patch ignores the FilePath argument
too -- justifiedly so. I just think it's better to pass in a well-formed
device path, rather than NULL. Because, the FilePath parameter is not
marked OPTIONAL in the spec.

> +	if (status != EFI_BUFFER_TOO_SMALL)
> +		return EFI_LOAD_ERROR;
> +
> +	status = efi_allocate_pages(initrd_size, &initrd_addr, max);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	status = efi_call_proto(lf2, load_file,
> +				(efi_device_path_protocol_t *)&initrd_devpath,
> +				false, &initrd_size, (void *)initrd_addr);

Same here.

> +	if (status != EFI_SUCCESS) {
> +		efi_free(initrd_size, initrd_addr);
> +		return status;
> +	}
> +
> +	*load_addr = initrd_addr;
> +	*load_size = initrd_size;
> +	return EFI_SUCCESS;
> +}
> diff --git a/drivers/firmware/efi/libstub/efistub.h b/drivers/firmware/efi/libstub/efistub.h
> index 99e93fd76ec5..fbf9f9442eed 100644
> --- a/drivers/firmware/efi/libstub/efistub.h
> +++ b/drivers/firmware/efi/libstub/efistub.h
> @@ -566,6 +566,14 @@ union efi_load_file_protocol {
>  	} mixed_mode;
>  };
>  
> +struct efi_vendor_dev_path {
> +	u8		type;
> +	u8		sub_type;
> +	u16		length;
> +	efi_guid_t	vendorguid;
> +	u8		vendordata[];
> +} __packed;
> +
>  void efi_pci_disable_bridge_busmaster(void);
>  
>  typedef efi_status_t (*efi_exit_boot_map_processing)(
> @@ -651,4 +659,8 @@ efi_status_t efi_load_initrd(efi_loaded_image_t *image,
>  			     unsigned long *load_addr,
>  			     unsigned long *load_size);
>  
> +efi_status_t efi_load_initrd_devpath(unsigned long *load_addr,
> +				     unsigned long *load_size,
> +				     unsigned long max);
> +
>  #endif
> diff --git a/drivers/firmware/efi/libstub/x86-stub.c b/drivers/firmware/efi/libstub/x86-stub.c
> index f3e2ff31b624..7f38f95676dd 100644
> --- a/drivers/firmware/efi/libstub/x86-stub.c
> +++ b/drivers/firmware/efi/libstub/x86-stub.c
> @@ -419,9 +419,20 @@ efi_status_t __efiapi efi_pe_entry(efi_handle_t handle,
>  	if (status != EFI_SUCCESS)
>  		goto fail2;
>  
> -	status = efi_load_initrd(image, hdr->initrd_addr_max,
> -				 above4g ? ULONG_MAX : hdr->initrd_addr_max,
> -				 &ramdisk_addr, &ramdisk_size);
> +	/*
> +	 * The initrd loaded from the Linux initrd vendor device
> +	 * path should take precedence, as we don't want the
> +	 * [unverified] command line to override the initrd
> +	 * supplied by the [potentially verified] firmware.
> +	 */
> +	status = efi_load_initrd_devpath(&ramdisk_addr, &ramdisk_size,
> +					 above4g ? ULONG_MAX
> +						 : hdr->initrd_addr_max);
> +	if (status == EFI_NOT_FOUND)
> +		status = efi_load_initrd(image, hdr->initrd_addr_max,
> +					 above4g ? ULONG_MAX
> +						 : hdr->initrd_addr_max,
> +					 &ramdisk_addr, &ramdisk_size);

Fallback#2, for x86, also looks good.

>  	if (status != EFI_SUCCESS)
>  		goto fail2;
>  	hdr->ramdisk_image = ramdisk_addr & 0xffffffff;
> @@ -732,6 +743,25 @@ struct boot_params *efi_main(efi_handle_t handle,
>  			 ((u64)boot_params->ext_cmd_line_ptr << 32));
>  	efi_parse_options((char *)cmdline_paddr);
>  
> +	if (!hdr->ramdisk_size && !boot_params->ext_ramdisk_size) {
> +		unsigned long max = hdr->initrd_addr_max;
> +		unsigned long addr, size;
> +
> +		if (hdr->xloadflags & XLF_CAN_BE_LOADED_ABOVE_4G)
> +			max = ULONG_MAX;
> +
> +		status = efi_load_initrd_devpath(&addr, &size, max);
> +		if (status == EFI_SUCCESS) {
> +			hdr->ramdisk_image		= (u32)addr;
> +			hdr->ramdisk_size 		= (u32)size;
> +			boot_params->ext_ramdisk_image	= (u64)addr >> 32;
> +			boot_params->ext_ramdisk_size 	= (u64)size >> 32;
> +		} else if (status != EFI_NOT_FOUND) {
> +			efi_printk("efi_load_initrd_devpath() failed!\n");
> +			goto fail;
> +		}
> +	}
> +

No fallback here; this is not a replacement for efi_load_initrd(), but a
brand new call. Why? (It's probably justified, I just don't know enough
about the kernel.)

>  	/*
>  	 * If the boot loader gave us a value for secure_boot then we use that,
>  	 * otherwise we ask the BIOS.
> diff --git a/include/linux/efi.h b/include/linux/efi.h
> index 9ccf313fe9de..75c83c322c40 100644
> --- a/include/linux/efi.h
> +++ b/include/linux/efi.h
> @@ -353,6 +353,7 @@ void efi_native_runtime_setup(void);
>  #define LINUX_EFI_TPM_EVENT_LOG_GUID		EFI_GUID(0xb7799cb0, 0xeca2, 0x4943,  0x96, 0x67, 0x1f, 0xae, 0x07, 0xb7, 0x47, 0xfa)
>  #define LINUX_EFI_TPM_FINAL_LOG_GUID		EFI_GUID(0x1e2ed096, 0x30e2, 0x4254,  0xbd, 0x89, 0x86, 0x3b, 0xbe, 0xf8, 0x23, 0x25)
>  #define LINUX_EFI_MEMRESERVE_TABLE_GUID		EFI_GUID(0x888eb0c6, 0x8ede, 0x4ff5,  0xa8, 0xf0, 0x9a, 0xee, 0x5c, 0xb9, 0x77, 0xc2)
> +#define LINUX_EFI_INITRD_MEDIA_GUID		EFI_GUID(0x5568e427, 0x68fc, 0x4f3d,  0xac, 0x74, 0xca, 0x55, 0x52, 0x31, 0xcc, 0x68)
>  
>  /* OEM GUIDs */
>  #define DELLEMC_EFI_RCI2_TABLE_GUID		EFI_GUID(0x2d9f28a2, 0xa886, 0x456a,  0x97, 0xa8, 0xf1, 0x1e, 0xf2, 0x4f, 0xf4, 0x55)
> 

Thanks,
Laszlo


WARNING: multiple messages have this Message-ID (diff)
From: Laszlo Ersek <lersek@redhat.com>
To: Ard Biesheuvel <ardb@kernel.org>, linux-efi@vger.kernel.org
Cc: agraf@csgraf.de, xypron.glpk@gmx.de, daniel.kiper@oracle.com,
	ilias.apalodimas@linaro.org, mjg59@google.com, pjones@redhat.com,
	leif@nuviainc.com, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 1/2] efi/libstub: add support for loading the initrd from a device path
Date: Fri, 7 Feb 2020 10:48:30 +0100	[thread overview]
Message-ID: <43362e18-eddc-9903-0e63-9d3eebe70313@redhat.com> (raw)
In-Reply-To: <20200206140352.6300-2-ardb@kernel.org>

On 02/06/20 15:03, Ard Biesheuvel wrote:
> There are currently two ways to specify the initrd to be passed to the
> Linux kernel when booting via the EFI stub:
> - it can be passed as a initrd= command line option when doing a pure PE
>   boot (as opposed to the EFI handover protocol that exists for x86)
> - otherwise, the bootloader or firmware can load the initrd into memory,
>   and pass the address and size via the bootparams struct (x86) or
>   device tree (ARM)
> 
> In the first case, we are limited to loading from the same file system
> that the kernel was loaded from, and it is also problematic in a trusted
> boot context, given that we cannot easily protect the command line from
> tampering without either adding complicated white/blacklisting of boot
> arguments or locking down the command line altogether.
> 
> In the second case, we force the bootloader to duplicate knowledge about
> the boot protocol which is already encoded in the stub, and which may be
> subject to change over time, e.g., bootparams struct definitions, memory
> allocation/alignment requirements for the placement of the initrd etc etc.
> In the ARM case, it also requires the bootloader to modify the hardware
> description provided by the firmware, as it is passed in the same file.
> On systems where the initrd is measured after loading, it creates a time
> window where the initrd contents might be manipulated in memory before
> handing over to the kernel.
> 
> Address these concerns by adding support for loading the initrd into
> memory by invoking the EFI LoadFile2 protocol installed on a vendor
> GUIDed device path that specifically designates a Linux initrd.
> This addresses the above concerns, by putting the EFI stub in charge of
> placement in memory and of passing the base and size to the kernel proper
> (via whatever means it desires) while still leaving it up to the firmware
> or bootloader to obtain the file contents, potentially from other file
> systems than the one the kernel itself was loaded from. On platforms that
> implement measured boot, it permits the firmware to take the measurement
> right before the kernel actually consumes the contents.
> 
> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
> ---
>  drivers/firmware/efi/libstub/arm-stub.c        | 16 +++--
>  drivers/firmware/efi/libstub/efi-stub-helper.c | 65 ++++++++++++++++++++
>  drivers/firmware/efi/libstub/efistub.h         | 12 ++++
>  drivers/firmware/efi/libstub/x86-stub.c        | 36 ++++++++++-
>  include/linux/efi.h                            |  1 +
>  5 files changed, 123 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/firmware/efi/libstub/arm-stub.c b/drivers/firmware/efi/libstub/arm-stub.c
> index c7b091f50e55..1db943c1ba2b 100644
> --- a/drivers/firmware/efi/libstub/arm-stub.c
> +++ b/drivers/firmware/efi/libstub/arm-stub.c
> @@ -157,6 +157,7 @@ unsigned long efi_entry(void *handle, efi_system_table_t *sys_table_arg,
>  	enum efi_secureboot_mode secure_boot;
>  	struct screen_info *si;
>  	efi_properties_table_t *prop_tbl;
> +	unsigned long max_addr;
>  
>  	sys_table = sys_table_arg;
>  
> @@ -255,11 +256,18 @@ unsigned long efi_entry(void *handle, efi_system_table_t *sys_table_arg,
>  	if (!fdt_addr)
>  		pr_efi("Generating empty DTB\n");
>  
> -	status = efi_load_initrd(image, ULONG_MAX,
> -				 efi_get_max_initrd_addr(dram_base, *image_addr),
> -				 &initrd_addr, &initrd_size);
> +	max_addr = efi_get_max_initrd_addr(dram_base, *image_addr);
> +	status = efi_load_initrd_devpath(&initrd_addr, &initrd_size, max_addr);
> +	if (status == EFI_SUCCESS)
> +		pr_efi("Loaded initrd from LINUX_EFI_INITRD_MEDIA_GUID device path\n");
> +	else if (status == EFI_NOT_FOUND) {
> +		status = efi_load_initrd(image, ULONG_MAX, max_addr,
> +					 &initrd_addr, &initrd_size);

- So this seems to be fallback#1, for ARM, which looks good.

- Are you sure you only want to fall back to the old method on
EFI_NOT_FOUND? Wouldn't other return values from
efi_load_initrd_devpath() justify that too?

... After checking the boot services called in
efi_load_initrd_devpath(), this idea seems reasonable, but then I'd
suggest documenting the significance of returning EFI_NOT_FOUND near the
efi_load_initrd_devpath() function declaration, in "efistub.h".

> +		if (status == EFI_SUCCESS)
> +			pr_efi("Loaded initrd from command line option\n");
> +	}
>  	if (status != EFI_SUCCESS)
> -		pr_efi_err("Failed initrd from command line!\n");
> +		pr_efi_err("Failed to load initrd!\n");
>  
>  	efi_random_get_seed();
>  
> diff --git a/drivers/firmware/efi/libstub/efi-stub-helper.c b/drivers/firmware/efi/libstub/efi-stub-helper.c
> index 8e60a39df3c5..eaf45ea749b3 100644
> --- a/drivers/firmware/efi/libstub/efi-stub-helper.c
> +++ b/drivers/firmware/efi/libstub/efi-stub-helper.c
> @@ -323,3 +323,68 @@ void efi_char16_printk(efi_char16_t *str)
>  	efi_call_proto(efi_table_attr(efi_system_table(), con_out),
>  		       output_string, str);
>  }
> +
> +static const struct {
> +	struct efi_vendor_dev_path	vendor;
> +	struct efi_generic_dev_path	end;
> +} __packed initrd_devpath = {
> +	{
> +		EFI_DEV_MEDIA,
> +		EFI_DEV_MEDIA_VENDOR,
> +		sizeof(struct efi_vendor_dev_path),
> +		LINUX_EFI_INITRD_MEDIA_GUID
> +	}, {
> +		EFI_DEV_END_PATH,
> +		EFI_DEV_END_ENTIRE,
> +		sizeof(struct efi_generic_dev_path)
> +	}
> +};
> +
> +efi_status_t efi_load_initrd_devpath(unsigned long *load_addr,
> +				     unsigned long *load_size,
> +				     unsigned long max)
> +{
> +	efi_guid_t lf2_proto_guid = EFI_LOAD_FILE2_PROTOCOL_GUID;
> +	efi_device_path_protocol_t *dp;
> +	efi_load_file2_protocol_t *lf2;
> +	unsigned long initrd_addr;
> +	unsigned long initrd_size;
> +	efi_handle_t handle;
> +	efi_status_t status;
> +
> +	if (!load_addr || !load_size)
> +		return EFI_INVALID_PARAMETER;
> +
> +	dp = (efi_device_path_protocol_t *)&initrd_devpath;
> +	status = efi_bs_call(locate_device_path, &lf2_proto_guid, &dp, &handle);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	status = efi_bs_call(handle_protocol, handle, &lf2_proto_guid,
> +			     (void **)&lf2);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	initrd_size = 0;
> +	status = efi_call_proto(lf2, load_file,
> +				(efi_device_path_protocol_t *)&initrd_devpath,
> +				false, &initrd_size, NULL);

The second argument to EFI_LOAD_FILE2_PROTOCOL.LoadFile() is "FilePath",
specified as "The device specific path of the file to load". This means
it is supposed to be a (possibly empty) sequence of FILEPATH_DEVICE_PATH
nodes, terminated by and "End Entire Device Path" node. See

- 10.3.1 Generic Device Path Structures
- 10.3.5.4 File Path Media Device Path

in UEFI-2.8.

And "initrd_devpath" is not a device path like that; instead it's the
VenMedia device path that's installed on the handle that also carries
our LoadFile2 instance.

Now, I do see that this all theoretical here, as we don't expect the
LoadFile2 instance that we've found via our special
LINUX_EFI_INITRD_MEDIA_GUID VenMedia devpath to do *any* device-specific
filename / pathname parsing.

But in that case (i.e., given that the FilePath argument is totally
irrelevant), I think it's much clearer if we simply pass an empty device
path -- one that consists of a single "End Entire Device Path" node.

I've checked, and your ArmVirtQemu patch ignores the FilePath argument
too -- justifiedly so. I just think it's better to pass in a well-formed
device path, rather than NULL. Because, the FilePath parameter is not
marked OPTIONAL in the spec.

> +	if (status != EFI_BUFFER_TOO_SMALL)
> +		return EFI_LOAD_ERROR;
> +
> +	status = efi_allocate_pages(initrd_size, &initrd_addr, max);
> +	if (status != EFI_SUCCESS)
> +		return status;
> +
> +	status = efi_call_proto(lf2, load_file,
> +				(efi_device_path_protocol_t *)&initrd_devpath,
> +				false, &initrd_size, (void *)initrd_addr);

Same here.

> +	if (status != EFI_SUCCESS) {
> +		efi_free(initrd_size, initrd_addr);
> +		return status;
> +	}
> +
> +	*load_addr = initrd_addr;
> +	*load_size = initrd_size;
> +	return EFI_SUCCESS;
> +}
> diff --git a/drivers/firmware/efi/libstub/efistub.h b/drivers/firmware/efi/libstub/efistub.h
> index 99e93fd76ec5..fbf9f9442eed 100644
> --- a/drivers/firmware/efi/libstub/efistub.h
> +++ b/drivers/firmware/efi/libstub/efistub.h
> @@ -566,6 +566,14 @@ union efi_load_file_protocol {
>  	} mixed_mode;
>  };
>  
> +struct efi_vendor_dev_path {
> +	u8		type;
> +	u8		sub_type;
> +	u16		length;
> +	efi_guid_t	vendorguid;
> +	u8		vendordata[];
> +} __packed;
> +
>  void efi_pci_disable_bridge_busmaster(void);
>  
>  typedef efi_status_t (*efi_exit_boot_map_processing)(
> @@ -651,4 +659,8 @@ efi_status_t efi_load_initrd(efi_loaded_image_t *image,
>  			     unsigned long *load_addr,
>  			     unsigned long *load_size);
>  
> +efi_status_t efi_load_initrd_devpath(unsigned long *load_addr,
> +				     unsigned long *load_size,
> +				     unsigned long max);
> +
>  #endif
> diff --git a/drivers/firmware/efi/libstub/x86-stub.c b/drivers/firmware/efi/libstub/x86-stub.c
> index f3e2ff31b624..7f38f95676dd 100644
> --- a/drivers/firmware/efi/libstub/x86-stub.c
> +++ b/drivers/firmware/efi/libstub/x86-stub.c
> @@ -419,9 +419,20 @@ efi_status_t __efiapi efi_pe_entry(efi_handle_t handle,
>  	if (status != EFI_SUCCESS)
>  		goto fail2;
>  
> -	status = efi_load_initrd(image, hdr->initrd_addr_max,
> -				 above4g ? ULONG_MAX : hdr->initrd_addr_max,
> -				 &ramdisk_addr, &ramdisk_size);
> +	/*
> +	 * The initrd loaded from the Linux initrd vendor device
> +	 * path should take precedence, as we don't want the
> +	 * [unverified] command line to override the initrd
> +	 * supplied by the [potentially verified] firmware.
> +	 */
> +	status = efi_load_initrd_devpath(&ramdisk_addr, &ramdisk_size,
> +					 above4g ? ULONG_MAX
> +						 : hdr->initrd_addr_max);
> +	if (status == EFI_NOT_FOUND)
> +		status = efi_load_initrd(image, hdr->initrd_addr_max,
> +					 above4g ? ULONG_MAX
> +						 : hdr->initrd_addr_max,
> +					 &ramdisk_addr, &ramdisk_size);

Fallback#2, for x86, also looks good.

>  	if (status != EFI_SUCCESS)
>  		goto fail2;
>  	hdr->ramdisk_image = ramdisk_addr & 0xffffffff;
> @@ -732,6 +743,25 @@ struct boot_params *efi_main(efi_handle_t handle,
>  			 ((u64)boot_params->ext_cmd_line_ptr << 32));
>  	efi_parse_options((char *)cmdline_paddr);
>  
> +	if (!hdr->ramdisk_size && !boot_params->ext_ramdisk_size) {
> +		unsigned long max = hdr->initrd_addr_max;
> +		unsigned long addr, size;
> +
> +		if (hdr->xloadflags & XLF_CAN_BE_LOADED_ABOVE_4G)
> +			max = ULONG_MAX;
> +
> +		status = efi_load_initrd_devpath(&addr, &size, max);
> +		if (status == EFI_SUCCESS) {
> +			hdr->ramdisk_image		= (u32)addr;
> +			hdr->ramdisk_size 		= (u32)size;
> +			boot_params->ext_ramdisk_image	= (u64)addr >> 32;
> +			boot_params->ext_ramdisk_size 	= (u64)size >> 32;
> +		} else if (status != EFI_NOT_FOUND) {
> +			efi_printk("efi_load_initrd_devpath() failed!\n");
> +			goto fail;
> +		}
> +	}
> +

No fallback here; this is not a replacement for efi_load_initrd(), but a
brand new call. Why? (It's probably justified, I just don't know enough
about the kernel.)

>  	/*
>  	 * If the boot loader gave us a value for secure_boot then we use that,
>  	 * otherwise we ask the BIOS.
> diff --git a/include/linux/efi.h b/include/linux/efi.h
> index 9ccf313fe9de..75c83c322c40 100644
> --- a/include/linux/efi.h
> +++ b/include/linux/efi.h
> @@ -353,6 +353,7 @@ void efi_native_runtime_setup(void);
>  #define LINUX_EFI_TPM_EVENT_LOG_GUID		EFI_GUID(0xb7799cb0, 0xeca2, 0x4943,  0x96, 0x67, 0x1f, 0xae, 0x07, 0xb7, 0x47, 0xfa)
>  #define LINUX_EFI_TPM_FINAL_LOG_GUID		EFI_GUID(0x1e2ed096, 0x30e2, 0x4254,  0xbd, 0x89, 0x86, 0x3b, 0xbe, 0xf8, 0x23, 0x25)
>  #define LINUX_EFI_MEMRESERVE_TABLE_GUID		EFI_GUID(0x888eb0c6, 0x8ede, 0x4ff5,  0xa8, 0xf0, 0x9a, 0xee, 0x5c, 0xb9, 0x77, 0xc2)
> +#define LINUX_EFI_INITRD_MEDIA_GUID		EFI_GUID(0x5568e427, 0x68fc, 0x4f3d,  0xac, 0x74, 0xca, 0x55, 0x52, 0x31, 0xcc, 0x68)
>  
>  /* OEM GUIDs */
>  #define DELLEMC_EFI_RCI2_TABLE_GUID		EFI_GUID(0x2d9f28a2, 0xa886, 0x456a,  0x97, 0xa8, 0xf1, 0x1e, 0xf2, 0x4f, 0xf4, 0x55)
> 

Thanks,
Laszlo


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  parent reply	other threads:[~2020-02-07  9:48 UTC|newest]

Thread overview: 77+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-06 14:03 [PATCH 0/2] arch-agnostic initrd loading method for EFI systems Ard Biesheuvel
2020-02-06 14:03 ` Ard Biesheuvel
2020-02-06 14:03 ` [PATCH 1/2] efi/libstub: add support for loading the initrd from a device path Ard Biesheuvel
2020-02-06 14:03   ` Ard Biesheuvel
2020-02-06 18:26   ` Heinrich Schuchardt
2020-02-06 18:26     ` Heinrich Schuchardt
2020-02-06 18:46     ` Ilias Apalodimas
2020-02-06 18:46       ` Ilias Apalodimas
2020-02-06 19:15       ` Heinrich Schuchardt
2020-02-06 19:15         ` Heinrich Schuchardt
2020-02-06 20:09         ` Ilias Apalodimas
2020-02-06 20:09           ` Ilias Apalodimas
2020-02-06 22:49           ` Heinrich Schuchardt
2020-02-06 22:49             ` Heinrich Schuchardt
2020-02-07  7:35             ` Ilias Apalodimas
2020-02-07  7:35               ` Ilias Apalodimas
2020-02-06 22:35     ` Ard Biesheuvel
2020-02-06 22:35       ` Ard Biesheuvel
2020-02-07  0:01       ` Heinrich Schuchardt
2020-02-07  0:01         ` Heinrich Schuchardt
2020-02-07  0:21         ` Ard Biesheuvel
2020-02-07  0:21           ` Ard Biesheuvel
2020-02-07  0:57           ` Heinrich Schuchardt
2020-02-07  0:57             ` Heinrich Schuchardt
2020-02-07  8:12             ` Ard Biesheuvel
2020-02-07  8:12               ` Ard Biesheuvel
2020-02-07 13:30               ` Heinrich Schuchardt
2020-02-07 13:30                 ` Heinrich Schuchardt
2020-02-07 13:58                 ` Ard Biesheuvel
2020-02-07 13:58                   ` Ard Biesheuvel
2020-02-07 14:18                   ` Alexander Graf
2020-02-07 14:18                     ` Alexander Graf
2020-02-07 15:30                     ` Ard Biesheuvel
2020-02-07 15:30                       ` Ard Biesheuvel
2020-02-07 15:35                     ` Heinrich Schuchardt
2020-02-07 15:35                       ` Heinrich Schuchardt
2020-02-07 11:09       ` Laszlo Ersek
2020-02-07 11:09         ` Laszlo Ersek
2020-02-07 11:03     ` Laszlo Ersek
2020-02-07 11:03       ` Laszlo Ersek
2020-02-07  9:48   ` Laszlo Ersek [this message]
2020-02-07  9:48     ` Laszlo Ersek
2020-02-07 12:36     ` Ard Biesheuvel
2020-02-07 12:36       ` Ard Biesheuvel
2020-02-10 14:26       ` Laszlo Ersek
2020-02-10 14:26         ` Laszlo Ersek
2020-02-09  6:39   ` Lukas Wunner
2020-02-09 11:35     ` Ard Biesheuvel
2020-02-09 11:35       ` Ard Biesheuvel
2020-02-06 14:03 ` [PATCH 2/2] efi/libstub: take noinitrd cmdline argument into account for devpath initrd Ard Biesheuvel
2020-02-06 14:03   ` Ard Biesheuvel
2020-02-06 18:33   ` Heinrich Schuchardt
2020-02-06 18:33     ` Heinrich Schuchardt
2020-02-06 23:44     ` Ard Biesheuvel
2020-02-06 23:44       ` Ard Biesheuvel
2020-02-12 16:01   ` Peter Jones
2020-02-12 16:01     ` Peter Jones
2020-02-07  9:09 ` [PATCH 0/2] arch-agnostic initrd loading method for EFI systems Laszlo Ersek
2020-02-07  9:09   ` Laszlo Ersek
2020-02-07  9:22   ` Laszlo Ersek
2020-02-07  9:22     ` Laszlo Ersek
2020-02-07 12:23     ` Ard Biesheuvel
2020-02-07 12:23       ` Ard Biesheuvel
2020-02-07 16:20       ` James Bottomley
2020-02-07 16:20         ` James Bottomley
2020-02-07 18:31         ` Ard Biesheuvel
2020-02-07 18:31           ` Ard Biesheuvel
2020-02-07 19:54           ` James Bottomley
2020-02-07 19:54             ` James Bottomley
2020-02-07 20:03             ` Ard Biesheuvel
2020-02-07 20:03               ` Ard Biesheuvel
2020-02-07 18:45 ` Arvind Sankar
2020-02-07 18:45   ` Arvind Sankar
2020-02-07 19:47   ` Ard Biesheuvel
2020-02-07 19:47     ` Ard Biesheuvel
2020-02-07 20:26     ` Arvind Sankar
2020-02-07 20:26       ` Arvind Sankar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=43362e18-eddc-9903-0e63-9d3eebe70313@redhat.com \
    --to=lersek@redhat.com \
    --cc=agraf@csgraf.de \
    --cc=ardb@kernel.org \
    --cc=daniel.kiper@oracle.com \
    --cc=ilias.apalodimas@linaro.org \
    --cc=leif@nuviainc.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-efi@vger.kernel.org \
    --cc=mjg59@google.com \
    --cc=pjones@redhat.com \
    --cc=xypron.glpk@gmx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.