Re: [PATCH v2 0/5] variable-order, large folios for anonymous memory

[Yin Fengwei <fengwei.yin@intel.com>]

On 7/4/23 23:36, Ryan Roberts wrote:
> On 04/07/2023 08:11, Yu Zhao wrote:
>> On Tue, Jul 4, 2023 at 12:22 AM Yin, Fengwei <fengwei.yin@intel.com> wrote:
>>>
>>> On 7/4/2023 10:18 AM, Yu Zhao wrote:
>>>> On Mon, Jul 3, 2023 at 7:53 AM Ryan Roberts <ryan.roberts@arm.com> wrote:
>>>>>
>>>>> Hi All,
>>>>>
>>>>> This is v2 of a series to implement variable order, large folios for anonymous
>>>>> memory. The objective of this is to improve performance by allocating larger
>>>>> chunks of memory during anonymous page faults. See [1] for background.
>>>>
>>>> Thanks for the quick response!
>>>>
>>>>> I've significantly reworked and simplified the patch set based on comments from
>>>>> Yu Zhao (thanks for all your feedback!). I've also renamed the feature to
>>>>> VARIABLE_THP, on Yu's advice.
>>>>>
>>>>> The last patch is for arm64 to explicitly override the default
>>>>> arch_wants_pte_order() and is intended as an example. If this series is accepted
>>>>> I suggest taking the first 4 patches through the mm tree and the arm64 change
>>>>> could be handled through the arm64 tree separately. Neither has any build
>>>>> dependency on the other.
>>>>>
>>>>> The one area where I haven't followed Yu's advice is in the determination of the
>>>>> size of folio to use. It was suggested that I have a single preferred large
>>>>> order, and if it doesn't fit in the VMA (due to exceeding VMA bounds, or there
>>>>> being existing overlapping populated PTEs, etc) then fallback immediately to
>>>>> order-0. It turned out that this approach caused a performance regression in the
>>>>> Speedometer benchmark.
>>>>
>>>> I suppose it's regression against the v1, not the unpatched kernel.
>>> From the performance data Ryan shared, it's against unpatched kernel:
>>>
>>> Speedometer 2.0:
>>>
>>> | kernel                         |   runs_per_min |
>>> |:-------------------------------|---------------:|
>>> | baseline-4k                    |           0.0% |
>>> | anonfolio-lkml-v1              |           0.7% |
>>> | anonfolio-lkml-v2-simple-order |          -0.9% |
>>> | anonfolio-lkml-v2              |           0.5% |
>>
>> I see. Thanks.
>>
>> A couple of questions:
>> 1. Do we have a stddev?
> 
> | kernel                    |   mean_abs |   std_abs |   mean_rel |   std_rel |
> |:------------------------- |-----------:|----------:|-----------:|----------:|
> | baseline-4k               |      117.4 |       0.8 |       0.0% |      0.7% |
> | anonfolio-v1              |      118.2 |         1 |       0.7% |      0.9% |
> | anonfolio-v2-simple-order |      116.4 |       1.1 |      -0.9% |      0.9% |
> | anonfolio-v2              |        118 |       1.2 |       0.5% |      1.0% |
> 
> This is with 3 runs per reboot across 5 reboots, with first run after reboot
> trimmed (it's always a bit slower, I assume due to cold page cache). So 10 data
> points per kernel in total.
> 
> I've rerun the test multiple times and see similar results each time.
> 
> I've also run anonfolio-v2 with Kconfig FLEXIBLE_THP=disabled and in this case I
> see the same performance as baseline-4k.
> 
> 
>> 2. Do we have a theory why it regressed?
> 
> I have a woolly hypothesis; I think Chromium is doing mmap/munmap in ways that
> mean when we fault, order-4 is often too big to fit in the VMA. So we fallback
> to order-0. I guess this is happening so often for this workload that the cost
> of doing the checks and fallback is outweighing the benefit of the memory that
> does end up with order-4 folios.
> 
> I've sampled the memory in each bucket (once per second) while running and its
> roughly:
> 
> 64K: 25%
> 32K: 15%
> 16K: 15%
> 4K: 45%
> 
> 32K and 16K obviously fold into the 4K bucket with anonfolio-v2-simple-order.
> But potentially, I suspect there is lots of mmap/unmap for the smaller sizes and
> the 64K contents is more static - that's just a guess though.
So this is like out of vma range thing.

> 
>> Assuming no bugs, I don't see how a real regression could happen --
>> falling back to order-0 isn't different from the original behavior.
>> Ryan, could you `perf record` and `cat /proc/vmstat` and share them?
> 
> I can, but it will have to be a bit later in the week. I'll do some more test
> runs overnight so we have a larger number of runs - hopefully that might tell us
> that this is noise to a certain extent.
> 
> I'd still like to hear a clear technical argument for why the bin-packing
> approach is not the correct one!
My understanding to Yu's (Yu, correct me if I am wrong) comments is that we
postpone this part of change and make basic anon large folio support in. Then
discuss which approach we should take. Maybe people will agree retry is the
choice, maybe other approach will be taken...

For example, for this out of VMA range case, per VMA order should be considered.
We don't need make decision that the retry should be taken now.


Regards
Yin, Fengwei

> 
> Thanks,
> Ryan
> 
> 
>