From mboxrd@z Thu Jan 1 00:00:00 1970 From: Hans Verkuil Subject: Re: [RFC PATCH v3 00/18] Support for Tegra video capture from external sensor Date: Fri, 17 Jul 2020 19:08:41 +0200 Message-ID: <458db01d-3c9c-1aec-0d28-edcbf0265aa4@xs4all.nl> References: <1594786855-26506-1-git-send-email-skomatineni@nvidia.com> Mime-Version: 1.0 Content-Type: text/plain; charset=utf-8 Content-Transfer-Encoding: 8bit Return-path: In-Reply-To: Content-Language: en-US Sender: linux-kernel-owner@vger.kernel.org To: Sowjanya Komatineni , thierry.reding@gmail.com, jonathanh@nvidia.com, frankc@nvidia.com, sakari.ailus@iki.fi, robh+dt@kernel.org, helen.koike@collabora.com Cc: digetx@gmail.com, sboyd@kernel.org, gregkh@linuxfoundation.org, linux-media@vger.kernel.org, devicetree@vger.kernel.org, linux-tegra@vger.kernel.org, linux-kernel@vger.kernel.org, linux-i2c@vger.kernel.org List-Id: linux-tegra@vger.kernel.org On 17/07/2020 18:34, Sowjanya Komatineni wrote: > > On 7/17/20 3:54 AM, Hans Verkuil wrote: >> Hi Sowjanya, >> >> On 15/07/2020 06:20, Sowjanya Komatineni wrote: >>> This series adds support for video capture from external camera sensor to >>> Tegra video driver. >>> >>> Jetson TX1 has camera expansion connector and supports custom camera module >>> designed as per TX1 design specification. >>> >>> This series also enables camera capture support for Jetson Nano which has >>> Raspberry PI camera header. >>> >>> This series is tested with IMX219 camera sensor. >>> >>> This series include, >>> >>> VI I2C related fixes >>> - Camera sensor programming happens through VI I2C which is on host1x bus. >>> - These patches includes device tree and I2C driver fixes for VI I2C. >>> >>> Tegra video driver updates >>> - TPG Vs Non-TPG based on Kconfig >>> - Support for external sensor video capture based on device graph from DT. >>> - Support for selection ioctl operations >>> - Tegra MIPI CSI pads calibration >>> - CSI T-CLK and T-HS settle time computation based on clock rates. >>> >>> Host1x driver updates >>> - Adds API to allow creating mipi device for specific device node. >>> - Splits MIPI pads calibrate start and waiting for calibration to be done. >>> >>> Device tree updates >>> - Adds camera connector 2V8, 1V8, 1V2 regulator supplies to Jetson TX1 DT. >>> - Enabled VI and CSI support in Jetson Nano DT. >> I'm doing a bit of stress testing with: >> >> while true; do v4l2-ctl --stream-mmap --stream-count=1; done >> >> and I see that the imx274 has often streaming failures: >> >> [ 172.025144] IMX274 8-001a: s_stream failed >> [ 179.025192] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 3132 = 870 (2 bytes) >> [ 179.033575] IMX274 8-001a: s_stream failed >> [ 226.525378] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 3130 = 878 (2 bytes) >> [ 226.533761] IMX274 8-001a: s_stream failed >> [ 227.029325] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 30f6 = 107 (2 bytes) >> [ 227.037758] IMX274 8-001a: s_stream failed >> [ 247.025218] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 30f6 = 107 (2 bytes) >> [ 247.033658] IMX274 8-001a: s_stream failed >> [ 293.025517] IMX274 8-001a: s_stream failed >> [ 309.024727] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 30e0 = 0 (2 bytes) >> [ 309.032969] IMX274 8-001a: s_stream failed >> [ 309.529506] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 30f8 = 11d2 (3 bytes) >> [ 309.538103] IMX274 8-001a: imx274_set_frame_length error = -121 >> [ 309.544102] IMX274 8-001a: imx274_set_frame_interval error = -121 >> [ 309.550243] IMX274 8-001a: s_stream failed >> [ 314.025561] IMX274 8-001a: s_stream failed >> [ 329.025586] IMX274 8-001a: s_stream failed >> [ 340.529567] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 303a = f0c (2 bytes) >> [ 340.538009] IMX274 8-001a: s_stream failed >> [ 347.525627] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 30f6 = 107 (2 bytes) >> [ 347.534008] IMX274 8-001a: s_stream failed >> [ 365.033640] IMX274 8-001a: s_stream failed >> [ 437.525788] IMX274 8-001a: imx274_write_mbreg : i2c bulk write failed, 3038 = c (2 bytes) >> [ 437.533997] IMX274 8-001a: s_stream failed >> [ 456.029780] IMX274 8-001a: s_stream failed >> [ 472.025862] IMX274 8-001a: s_stream failed >> [ 498.025861] IMX274 8-001a: s_stream failed >> [ 500.025905] IMX274 8-001a: s_stream failed >> >> where v4l2-ctl returns: >> >> VIDIOC_STREAMON returned -1 (Remote I/O error) >> >> I don't see this with the imx219. >> >> I also see this occasionally: >> >> [Fri Jul 17 12:51:42 2020] video4linux video1: failed to run capture start kthread: -4 >> >> Something is not stable here. >> >> Regards, >> >> Hans > > Hi Hans, > > Running the same single frame continuous loop for more than 2 hours now > and I don't see any failure. > > Above failure shows i2c bulk writes to IMX274 failure due to which > s_stream also failed. > > Not sure if its due to i2c mux in the path to sensor on your module > causing some issue when there is more i2c write traffic as we are doing > single stream in continuous loop. Also IMX219 does not show on your side > so something specific to IMX274 setup probably. I'll take a closer look next week. Good to know that it works fine for you. > > > Regarding kthread_run failure where kthread_run() returned -EINTR during > capture start thread, I always see this happen at the point of stopping > the continuous single stream while loop by pressing ctrl+c after few > loops of execution. Hmm, if this is normal behavior, then should this message be a debug message only? Or perhaps only show the message if the error code != EINTR. Regards, Hans > > while true; do v4l2-ctl --stream-mmap --stream-count=1; done > > when we stop loop with ctrl+c, v4l2-ctl terminates but loop does not > terminate immediately and probably SIGKILLed  is seen prior to complete. > > Using below can help to terminate loop as well when we stop ctrl-c and > with this I don't see any repro of EINTR error from kthread_run when run > in infinite loop. > > while true; do ./v4l2-ctl --stream-mmap --stream-count=1 || break; done > > > >>> >>> Delta between patch versions: >>> >>> [v3]: Includes v2 feedback >>> - Uses separate helper function for retrieving remote csi subdevice >>> and source subdevice. >>> - Added check for presence of subdevice ops set/get_selection >>> - dropped vb2_queue_release from driver and using >>> vb2_video_unregister_device instead of video_unregister_device. >>> - video device register should happen in the last after all video >>> device related setup is done in the driver. This is being addressed >>> in below RFC patch. Once proper implementation of this is available >>> will update Tegra video driver to use split APIs and do all setup >>> prior to device register. Added this as TODO in the driver. >>> https://www.spinics.net/lists/linux-media/msg172761.html >>> >>> Note: >>> Patch-0012 has compilation dependency on >>> https://patchwork.kernel.org/patch/11659521/ >>> >>> >>> [v2]: Includes below changes based on v1 feedback >>> - dt-binding document and the driver update for device graph to use >>> separate ports for sink endpoint and source endpoint for csi. >>> - Use data-lanes endpoint property for csi. >>> - Update tegra_mipi_request() to take device node pointer argument >>> rather than adding extra API. >>> - Remove checking for clk pointer before clk_disable. >>> >>> >>> Sowjanya Komatineni (18): >>> dt-bindings: i2c: tegra: Document Tegra210 VI I2C clocks and >>> power-domains >>> arm64: tegra: Add missing clocks and power-domains to Tegra210 VI I2C >>> i2c: tegra: Don't mark VI I2C as IRQ safe runtime PM >>> i2c: tegra: Remove NULL pointer check before >>> clk_enable/disable/prepare/unprepare >>> i2c: tegra: Fix the error path in tegra_i2c_runtime_resume >>> i2c: tegra: Fix runtime resume to re-init VI I2C >>> i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c >>> media: tegra-video: Fix channel format alignment >>> media: tegra-video: Enable TPG based on kernel config >>> media: tegra-video: Update format lookup to offset based >>> dt-bindings: tegra: Update VI and CSI bindings with port info >>> media: tegra-video: Add support for external sensor capture >>> media: tegra-video: Add support for selection ioctl ops >>> gpu: host1x: mipi: Update tegra_mipi_request() to be node based >>> gpu: host1x: mipi: Use readl_relaxed_poll_timeout in tegra_mipi_wait >>> gpu: host1x: mipi: Split tegra_mipi_calibrate and tegra_mipi_wait >>> media: tegra-video: Add CSI MIPI pads calibration >>> media: tegra-video: Compute settle times based on the clock rate >>> >>> .../display/tegra/nvidia,tegra20-host1x.txt | 92 ++- >>> .../devicetree/bindings/i2c/nvidia,tegra20-i2c.txt | 19 +- >>> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 6 + >>> drivers/gpu/drm/tegra/dsi.c | 9 +- >>> drivers/gpu/host1x/mipi.c | 37 +- >>> drivers/i2c/busses/i2c-tegra.c | 101 +-- >>> drivers/staging/media/tegra-video/Kconfig | 7 + >>> drivers/staging/media/tegra-video/csi.c | 247 ++++++- >>> drivers/staging/media/tegra-video/csi.h | 8 + >>> drivers/staging/media/tegra-video/tegra210.c | 25 +- >>> drivers/staging/media/tegra-video/vi.c | 793 +++++++++++++++++++-- >>> drivers/staging/media/tegra-video/vi.h | 25 +- >>> drivers/staging/media/tegra-video/video.c | 23 +- >>> include/linux/host1x.h | 4 +- >>> 14 files changed, 1242 insertions(+), 154 deletions(-) >>>