From: Tony Battersby <tonyb@cybernetics.com>
To: Jeff Garzik <jgarzik@pobox.com>, linux-ide@vger.kernel.org
Subject: AHCI problem with hotplug
Date: Thu, 11 Dec 2008 15:32:35 -0500 [thread overview]
Message-ID: <494178E3.6030305@cybernetics.com> (raw)
I am having a problem getting Linux to detect hot-plugged SATA disks on my
ICH7 AHCI controller (SuperMicro PDSME motherboard). On any SATA port that
already had a disk plugged in during BIOS POST, Linux will see the disk and
detect hot-plug and hot-unplug events just fine. On any SATA port that did
not have a disk plugged in during BIOS POST, Linux will not see a disk no
matter what. Here are the different sequences of events that I have tried:
1) boot with SATA disk plugged in
modprobe ahci: disk detected
unplug disk: disk deleted
plug in disk: disk detected
2) boot with SATA disk plugged in
unplug disk
modprobe ahci
plug in disk: disk detected
unplug disk: disk deleted
plug in disk: disk detected
unplug disk: disk deleted
plug in disk to any other SATA port -> not detected
plug in disk to the original SATA port -> disk detected
3) boot with SATA disk unplugged
plug in disk to any SATA port
modprobe ahci: not detected
grep ahci /proc/interrupts: 0 interrupts
4) boot with SATA disk unplugged
modprobe ahci
plug in disk to any SATA port: not detected
grep ahci /proc/interrupts: 0 interrupts
5) keep SATA disk plugged in during BIOS POST but unplug it before the
kernel boots
kernel hangs at "BIOS data check"
I have tried both 2.6.24.7 and 2.6.27.8 with the same result.
The BIOS is configured as follows:
Parallel ATA: [Enabled]
Serial ATA: [Enabled]
SATA Controller Mode: [Enhanced]
SATA RAID: [Disabled]
SATA AHCI: [Enabled]
The root filesystem is on a parallel IDE disk using the legacy (non-libata)
piix driver.
Kernel messages when the disk was plugged in before booting:
ahci_init_one: ENTER
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ata_host_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ahci_port_init: PORT_SCR_ERR 0x0
ahci_port_init: PORT_IRQ_STAT 0x0
ahci_init_controller: HOST_CTL 0x80000000
ahci_init_controller: HOST_CTL 0x80000002
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0x1 impl SATA
mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xed000400 port 0xed000500 irq 505
ata2: DUMMY
ata3: DUMMY
ata4: DUMMY
ata_host_register: probe begin
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata1 port frozen
ahci_hardreset: ENTER
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ata_dev_classify: found ATA device by sig
ahci_hardreset: EXIT, rc=0, class=1
ata_eh_thaw_port: ata1 port thawed
ata_std_postreset: ENTER
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata1.00: ata_dev_read_id: ENTER
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: ENTER
ahci_interrupt: ENTER
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f61 84:4163 85:7469
86:be41 87:4163 88:207f
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01fe 81==0x0000 82==0x746b 83==0x7f61 84==0x4163
ata_dump_id: 88==0x207f 93==0x0000
ata1.00: ATA-8: WDC WD2502ABYS-01B7A0, 02.03B02, max UDMA/133
ata1.00: 490350672 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata_dev_set_xfermode: set features - xfer mode
ahci_interrupt: ENTER
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata_dev_set_xfermode: EXIT, err_mask=0
ata1.00: ata_dev_read_id: ENTER
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: ENTER
ahci_interrupt: ENTER
ahci_interrupt: port 0
ahci_interrupt: EXIT
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata1.00: ata_dev_configure: cfg 49:2f00 82:746b 83:7f61 84:4163 85:7469
86:be41 87:4163 88:407f
ata_dump_id: 49==0x2f00 53==0x0007 63==0x0007 64==0x0003 75==0x001f
ata_dump_id: 80==0x01fe 81==0x0000 82==0x746b 83==0x7f61 84==0x4163
ata_dump_id: 88==0x407f 93==0x0000
ata_dev_set_mode: xfer_shift=12, xfer_mode=0x46
ata1.00: configured for UDMA/133
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata2: ata_port_flush_task: EXIT
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata3: ata_port_flush_task: EXIT
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata4: ata_port_flush_task: EXIT
ata_scsi_error: EXIT
ata_host_register: host probe begin
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 24 00 00 00 00
ata_scsiop_inq_std: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 12 00 00 00 60 00 00 00 00
ata_scsiop_inq_std: ENTER
scsi 0:0:0:0: Direct-Access ATA WDC WD2502ABYS-0 02.0 PQ: 0
ANSI: 5
ata_scsi_dump_cdb: CDB (1:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
sd 0:0:0:0: [sda] 490350672 512-byte hardware sectors (251060 MB)
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 3f 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 24
ata_scsiop_mode_sense: ENTER
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
ata_scsi_dump_cdb: CDB (1:0,0,0) 00 00 00 00 00 00 00 00 00
ata_scsiop_noop: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 25 00 00 00 00 00 00 00 00
ata_scsiop_read_cap: ENTER
sd 0:0:0:0: [sda] 490350672 512-byte hardware sectors (251060 MB)
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 3f 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 08
ata_scsiop_mode_sense: ENTER
ata_scsi_dump_cdb: CDB (1:0,0,0) 5a 00 08 00 00 00 00 00 24
ata_scsiop_mode_sense: ENTER
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda:<3>ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 00 00 00 00 08
ata_scsi_translate: ENTER
scsi_10_lba_len: ten-byte command
ata_sg_setup: ENTER, ata1
ata_sg_setup: 1 sg elements mapped
ahci_fill_sg: ENTER
ata_scsi_translate: EXIT
ahci_interrupt: ENTER
ata_sg_clean: unmapping 1 sg elements
ahci_interrupt: port 0
ahci_interrupt: EXIT
sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
Kernel messages when the disk was unplugged during BIOS POST but plugged in
before modprobe ahci:
ahci_init_one: ENTER
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
ata_host_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ata_port_alloc: ENTER
ahci_port_init: PORT_SCR_ERR 0x0
ahci_port_init: PORT_IRQ_STAT 0x0
ahci_port_init: PORT_SCR_ERR 0x0
ahci_port_init: PORT_IRQ_STAT 0x0
ahci_port_init: PORT_SCR_ERR 0x0
ahci_port_init: PORT_IRQ_STAT 0x0
ahci_port_init: PORT_SCR_ERR 0x0
ahci_port_init: PORT_IRQ_STAT 0x0
ahci_init_controller: HOST_CTL 0x80000000
ahci_init_controller: HOST_CTL 0x80000002
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA
mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ahci 0000:00:1f.2: setting latency timer to 64
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
__ata_port_freeze: ata4294967295 port frozen
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024@0xed000400 port 0xed000500 irq 505
ata2: SATA max UDMA/133 abar m1024@0xed000400 port 0xed000580 irq 505
ata3: SATA max UDMA/133 abar m1024@0xed000400 port 0xed000600 irq 505
ata4: SATA max UDMA/133 abar m1024@0xed000400 port 0xed000680 irq 505
ata_host_register: probe begin
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata1: ata_port_flush_task: EXIT
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata1 port frozen
ahci_hardreset: ENTER
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ahci_hardreset: EXIT, rc=0, class=0
ata_eh_thaw_port: ata1 port thawed
ata_std_postreset: ENTER
ata1: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata2: ata_port_flush_task: EXIT
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata2 port frozen
ahci_hardreset: ENTER
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ahci_hardreset: EXIT, rc=0, class=0
ata_eh_thaw_port: ata2 port thawed
ata_std_postreset: ENTER
ata2: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata3: ata_port_flush_task: EXIT
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata3 port frozen
ahci_hardreset: ENTER
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ahci_hardreset: EXIT, rc=0, class=0
ata_eh_thaw_port: ata3 port thawed
ata_std_postreset: ENTER
ata3: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_port_schedule_eh: port EH scheduled
ata_scsi_error: ENTER
ata_port_flush_task: ENTER
ata4: ata_port_flush_task: EXIT
ata_eh_link_autopsy: ENTER
ata_eh_recover: ENTER
__ata_port_freeze: ata4 port frozen
ahci_hardreset: ENTER
sata_link_hardreset: ENTER
sata_link_hardreset: EXIT, rc=0
ahci_hardreset: EXIT, rc=0, class=0
ata_eh_thaw_port: ata4 port thawed
ata_std_postreset: ENTER
ata4: SATA link down (SStatus 0 SControl 0)
ata_std_postreset: EXIT
ata_eh_revalidate_and_attach: ENTER
ata_eh_recover: EXIT, rc=0
ata_scsi_error: EXIT
ata_host_register: host probe begin
lspci -vv
00:00.0 Host bridge: Intel Corporation E7230/3000/3010 Memory Controller
Hub (rev 81)
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:01.0 PCI bridge: Intel Corporation E7230/3000/3010 PCI Express Root
Port (rev 81) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=03, sec-latency=0
Memory behind bridge: ed100000-ed1fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [88] Subsystem: Super Micro Computer Inc Unknown
device 7780
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Address: fee0300c Data: 4159
Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 <1us, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot #1000, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Capabilities: [140] Root Complex Link <?>
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express
Port 1 (rev 01) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1,
Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Address: fee0300c Data: 4161
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown
device 7780
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
00:1c.4 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 5 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00007000-00007fff
Memory behind bridge: ed200000-ed2fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 5, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Address: fee0300c Data: 4169
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown
device 7780
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
00:1c.5 PCI bridge: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI
Express Port 6 (rev 01) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 00008000-00008fff
Memory behind bridge: ed300000-ed3fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
unlimited, L1 unlimited
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1,
Latency L0 <256ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surpise+
Slot # 6, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Address: fee0300c Data: 4171
Capabilities: [90] Subsystem: Super Micro Computer Inc Unknown
device 7780
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [100] Virtual Channel <?>
Capabilities: [180] Root Complex Link <?>
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #1 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 64e0 [size=32]
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #2 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 6800 [size=32]
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #3 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 6820 [size=32]
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI
Controller #4 (rev 01) (prog-if 00 [UHCI])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 6840 [size=32]
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI
Controller (rev 01) (prog-if 20 [EHCI])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if
01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=32
I/O behind bridge: 00009000-00009fff
Memory behind bridge: ed400000-eeffffff
Prefetchable memory behind bridge: 0000000030000000-00000000300fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [50] Subsystem: Super Micro Computer Inc Unknown
device 7780
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC
Interface Bridge (rev 01)
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information <?>
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE
Controller (rev 01) (prog-if 8a [Master SecP PriP])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 64d0 [size=16]
00:1f.2 SATA controller: Intel Corporation 82801GR/GH (ICH7 Family) SATA
AHCI Controller (rev 01) (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 507
Region 0: I/O ports at 6898 [size=8]
Region 1: I/O ports at 687c [size=4]
Region 2: I/O ports at 6890 [size=8]
Region 3: I/O ports at 6878 [size=4]
Region 4: I/O ports at 6880 [size=16]
Region 5: Memory at ed000400 (32-bit, non-prefetchable) [size=1K]
Capabilities: [80] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable+
Address: fee0300c Data: 4189
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller
(rev 01)
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1100 [size=32]
01:00.0 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
A (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=02, subordinate=02, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=100MHz
Status: Dev=01:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [300] Power Budgeting <?>
01:00.1 PIC: Intel Corporation 6700/6702PXH I/OxAPIC Interrupt
Controller A (rev 09) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at ed100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.2 PCI bridge: Intel Corporation 6700PXH PCI Express-to-PCI Bridge
B (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=01, secondary=03, subordinate=03, sec-latency=64
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [5c] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
Status: Dev=01:00.2 64bit- 133MHz- SCD- USC- SCO- SRD-
Upstream: Capacity=65535 CommitmentLimit=65535
Downstream: Capacity=65535 CommitmentLimit=65535
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [300] Power Budgeting <?>
01:00.3 PIC: Intel Corporation 6700PXH I/OxAPIC Interrupt Controller B
(rev 09) (prog-if 20 [IO(X)-APIC])
Subsystem: Super Micro Computer Inc Unknown device 7780
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at ed101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns,
L1 <1us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 256 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency
L0 unlimited, L1 unlimited
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
05:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet
Controller (Copper) (rev 03)
Subsystem: Super Micro Computer Inc Unknown device 108c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 506
Region 0: Memory at ed200000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 7000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000fee0300c Data: 41a9
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown,
Latency L0 <128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number a4-8d-86-ff-ff-48-30-00
06:00.0 Ethernet controller: Intel Corporation 82573E Gigabit Ethernet
Controller (Copper) (rev 03)
Subsystem: Super Micro Computer Inc Unknown device 108c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 505
Region 0: Memory at ed300000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 8000 [size=32]
Capabilities: [c8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [d0] Message Signalled Interrupts: Mask- 64bit+
Queue=0/0 Enable+
Address: 00000000fee0300c Data: 41c1
Capabilities: [e0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM unknown,
Latency L0 <128ns, L1 <64us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [140] Device Serial Number a5-8d-86-ff-ff-48-30-00
0a:04.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
(prog-if 00 [VGA controller])
Subsystem: ATI Technologies Inc Rage XL
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 66 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at ed400000 (32-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 30000000 [disabled] [size=128K]
Capabilities: [5c] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
next reply other threads:[~2008-12-11 21:00 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-12-11 20:32 Tony Battersby [this message]
2008-12-12 16:03 ` AHCI problem with hotplug Alan Cox
2008-12-29 8:17 ` Tejun Heo
2008-12-29 14:51 ` Tony Battersby
2008-12-29 18:29 ` Robert Hancock
2008-12-30 0:38 ` Tejun Heo
2009-01-02 3:12 ` Tejun Heo
2009-01-07 15:39 ` Tony Battersby
2009-01-08 2:06 ` Tejun Heo
2009-01-08 14:20 ` Tony Battersby
2009-01-09 0:13 ` Robert Hancock
2009-01-09 16:30 ` Tony Battersby
2009-01-14 6:33 ` Tejun Heo
2009-01-14 21:38 ` Tony Battersby
2009-01-15 1:31 ` Tejun Heo
2009-01-15 4:42 ` Robert Hancock
2009-01-20 22:56 ` Tony Battersby
2008-12-30 13:41 ` raz ben yehuda
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=494178E3.6030305@cybernetics.com \
--to=tonyb@cybernetics.com \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.