From: "Leonardo H. Souza Hamada" <leonardo.hamada@ufra.edu.br>
To: linux-wireless@vger.kernel.org
Subject: Re: zd1211rw on ppc (iBook G4)
Date: Tue, 01 Sep 2009 17:02:08 -0300 [thread overview]
Message-ID: <4A9D7DC0.6050701@ufra.edu.br> (raw)
In-Reply-To: <3ace41890908311126m5212926cl27172ae775fc92f2@mail.gmail.com>
Some more diagnostic info for the rw driver, this time compiled as
built-in and debug option in the kernel for 2.6.30.
dmesg for rw driver output:
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: New USB device found, idVendor=0411, idProduct=00da
usb 1-2: New USB device strings: Mfr=16, Product=32, SerialNumber=0
usb 1-2: Product: USB2.0 WLAN
usb 1-2: Manufacturer: Buffalo
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: print_id() 0411:00da v4810 high
usb 1-2: reset high speed USB device using ehci_hcd and address 2
zd1211rw 1-2:1.0: zd_chip_read_mac_addr_fw()
phy0: Selected rate control algorithm 'minstrel'
zd1211rw 1-2:1.0: probe() successful
zd1211rw 1-2:1.0: phy0
zd1211rw 1-2:1.0: zd_usb_init_hw()
usb 1-2: request_fw_file() fw name zd1211/zd1211b_ub
usb 1-2: firmware: requesting zd1211/zd1211b_ub
usb 1-2: upload_firmware() firmware device id 0x4810 is equal to the
actual device id
usb 1-2: request_fw_file() fw name zd1211/zd1211b_uphr
usb 1-2: firmware: requesting zd1211/zd1211b_uphr
usb 1-2: upload_code() transfer size 4096
usb 1-2: upload_code() transfer size 1024
usb 1-2: upload_code() firmware confirm return value 0x01
zd1211rw 1-2:1.0: zd_usb_enable_int()
zd1211rw 1-2:1.0: zd_usb_enable_int() submit urb ce577580
zd1211rw 1-2:1.0: zd_chip_init_hw()
zd1211rw 1-2:1.0: dump_cr() CR_AFTER_PNP 0x00000000
zd1211rw 1-2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-2:1.0: read_fw_regs_offset() fw_regs_base: 0xf7f1
zd1211rw 1-2:1.0: read_pod() E2P_POD 0xa000011a
zd1211rw 1-2:1.0: read_pod() RF AL2230S_RF 0xa PA type 0x0 patch CCK 1
patch CR157 0 patch 6M 0 new PHY 1 link LED1 tx led 1
zd1211rw 1-2:1.0: hw_init()
zd1211rw 1-2:1.0: zd1211b_hw_reset_phy()
zd1211rw 1-2:1.0: zd1211b_hw_init_hmac()
zd1211rw 1-2:1.0: zd_usb_rfwrite() value 0x0241000 bits 24
zd1211rw 1-2:1.0: firmware version 4725
zd1211rw 1-2:1.0: dump_fw_registers() FW_FIRMWARE_VER 0x4725
zd1211rw 1-2:1.0: dump_fw_registers() FW_USB_SPEED 0x0001
zd1211rw 1-2:1.0: dump_fw_registers() FW_FIX_TX_RATE 0x0000
zd1211rw 1-2:1.0: dump_fw_registers() FW_LINK_STATUS 0x0000
zd1211rw 1-2:1.0: dump_cr() CR_AFTER_PNP 0x00000001
zd1211rw 1-2:1.0: dump_cr() CR_GPI_EN 0x00000000
zd1211rw 1-2:1.0: dump_cr() CR_INTERRUPT 0x00000000
zd1211rw 1-2:1.0: zd1211b chip 0411:00da v4810 high 00-16-01 AL2230S_RF
pa0 g--N-
zd1211rw 1-2:1.0: zd_read_regdomain() regdomain: 0x49
zd1211rw 1-2:1.0: zd_usb_disable_int() urb ce577580 killed
zd1211rw 1-2:1.0: zd_usb_init_hw() couldn't initialize mac. Error number 1
iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
tunl0 no wireless extensions.
gre0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Hin-Tak Leung wrote:
> I have a bunch of patches which bring the 2.22 vendor driver up to
> 2.6.29 and 3.0 the vendor driver up to 2.6.30:
> http://htl10.users.sourceforge.net/patchsets/
> It doesn't fix the rw driver, but might be good enough for you?
>
I have downloaded the vendor driver and applied your patchset.
Inserted the vendor { USB_DEVICE(0x0411, 0x00DA) }, in
ar2524drv/src/zdusb.c
Recompiled as zd1211REV_B
dmesg for vendor driver:
udev: starting version 145
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
zd1211 - version 3.0.0.56
vendor_id = 0411
product_id = 00da
USB 2.0 Host
Release Ver = 4810
EEPORM Ver = 4330
Finsih download Firmware. Ready to reboot
Finsih download Firmware. Ready to reboot
Finsih download Firmware. Ready to reboot
ohci1394 0002:20:0e.0: enabling device (0000 -> 0002)
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40]
MMIO=[f5000000-f50007ff] Max Packet=[2048] IR/IT contexts=[8/8]
PA type: 2
Airoha AL2230S_RF
Overwrite CR157 = 0x0
Overwrite CR47 = 0x10019
zd1205_config: EEP(HWFeature)=0xF7D0
AllowedChannel = 00013fff
Region:0
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
usbcore: registered new interface driver zd1211
I am able to do iwlist ath0 scanning, a list of acess point appears but
sometimes this fails.
iwlist ath0 scanning:
ath0 Scan completed :
Cell 01 - Address: 00:21:91:0E:0B:F7
ESSID:"adminWF10"
Mode:Master
Frequency=2.412 GHz (Channel 1)
Quality=46/100 Signal level=-74 dBm Noise
level=-96 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Cell 02 - Address: 00:1D:0F:D1:4D:D2
ESSID:"LGAA_P_CENTRAL_WF01"
Mode:Master
Frequency=2.437 GHz (Channel 6)
Quality=43/100 Signal level=-76 dBm Noise
level=-96 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
12 Mb/s; 24 Mb/s; 36 Mb/s; 9 Mb/s; 18 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Cell 03 - Address: 00:1B:11:87:A7:0C
ESSID:"ponto-acesso-mutsuo"
Mode:Master
Frequency=2.437 GHz (Channel 6)
Quality=43/100 Signal level=-76 dBm Noise
level=-96 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Scan again, it fails and works seemingly in an unknown manner.
iwlist ath0 scanning
ath0 Failed to read scan data : Resource temporarily unavailable
Some message in dmesg of relevance:
...
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
zd1211_USB_PACKAGE_READ_REGISTER: warning, restarting INT EP
zd1211_readl retry OK
....(many times over)
and
1211_readl failed for 5 attempts...Very Serious<3>1211_readl failed for
5 attempts...Very Serious<3>1211_readl failed for 5 attempts...Very
Serious<3>1211_readl failed for 5 attempts...Very Serious<3>1211_readl
failed for 5 attempts...Very Serious<3>1211_readl failed for 5
attempts...Very Serious<3>1211_readl failed for 5 attempts...Very
Serious<3>1211_readl failed for 5 attempts...Very Serious<3>1211_readl
failed for 5 attempts...Very Serious<3>1211_readl failed for 5
attempts...Very Serious<3>1211_readl failed for 5 attempts...Very
Serious<3>1211_readl failed for 5 attempts...Very Serious<3>1211_readl
failed for 5 attempts...Very Serious<3>1211_readl failed for 5
attempts...Very Serious<3>1211_readl failed for 5 attempts...Very
Serious<7>zd1205_notify_disjoin_event
Giving up .... for now.
Regards,
Leonardo
next prev parent reply other threads:[~2009-09-01 20:02 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-08-31 16:39 zd1211rw on ppc (iBook G4) Leonardo H. Souza Hamada
2009-08-31 17:25 ` Hin-Tak Leung
[not found] ` <4A9C0ADC.6050607@ufra.edu.br>
2009-08-31 18:26 ` Hin-Tak Leung
2009-08-31 19:27 ` Michael Buesch
2009-08-31 19:35 ` Hin-Tak Leung
[not found] ` <69e28c910908311414s191aafa6ib0bdae8ed4ace27d@mail.gmail.com>
[not found] ` <3ace41890908311602g4a976ec5k4f1f5145662cf183@mail.gmail.com>
2009-08-31 23:11 ` Gábor Stefanik
2009-09-01 12:56 ` Michael Buesch
2009-09-01 20:02 ` Leonardo H. Souza Hamada [this message]
2009-09-12 22:43 ` zd1211rw on ppc (iBook G4) -- Solved, somewhat) Leonardo H. Souza Hamada
2009-09-13 10:13 ` Hin-Tak Leung
2009-09-14 3:41 ` Hin-Tak Leung
2009-09-14 4:09 ` Luis R. Rodriguez
2009-09-14 16:47 ` Leonardo H. Souza Hamada
2009-09-14 21:11 ` Hin-Tak Leung
[not found] ` <8ea57b3c57061154c0d312925100c827.squirrel@webmail.ufra.edu.br>
2009-09-15 1:08 ` Hin-Tak Leung
2009-09-23 0:50 ` zd1211rw on ppc (iBook G4) Hin-Tak Leung
2009-09-27 19:14 ` Leonardo H. Souza Hamada
2009-09-27 20:08 ` Hin-Tak Leung
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4A9D7DC0.6050701@ufra.edu.br \
--to=leonardo.hamada@ufra.edu.br \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.