From: Igor Grinberg <grinberg@compulab.co.il>
To: linux-omap@vger.kernel.org
Subject: AM3517 (Sitara) MMC2 help
Date: Tue, 24 Aug 2010 15:42:04 +0300 [thread overview]
Message-ID: <4C73BE1C.7080503@compulab.co.il> (raw)
Hi,
I have am3517 based board and Libertas sdio (4 wires)
wifi connected directly (no transceiver / level shifter) on mmc2
(which is named mmc1 in s/w).
am3517 is configured (h/w) for 3.3V and so is Libertas wifi.
dmesg | grep mmc1 shows:
--------------cut------------------
mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0000 -> 0x0118
mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0000 -> 0x0118
mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0100 -> 0x0118
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc1: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 20 width 0 timing 0
mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x00000c00
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x80000c08
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 20 width 0 timing 0
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD0, argument 0x00000000
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD8, argument 0x000001aa
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD1, argument 0x00000000
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
-------------------cut---------------------
Libertas is powered up and gets reseted properly.
On the oscilloscope, I see some communication going
on the CMD line and stops after some time.
am3517 PSP from TI, does not even registers/enables
the wifi combo found on am3517evm.
Have anybody got the mmc2 working on am3517?
May be with transceiver?
Any help will be appreciated.
Thanks
--
Regards,
Igor.
next reply other threads:[~2010-08-24 12:42 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-24 12:42 Igor Grinberg [this message]
2010-08-25 0:29 ` AM3517 (Sitara) MMC2 help Laine Walker-Avina
2010-08-25 0:36 ` Laine Walker-Avina
2010-08-25 7:57 ` Igor Grinberg
2010-08-25 8:12 ` Igor Grinberg
2010-08-25 9:26 ` Igor Grinberg
2010-08-25 13:46 ` Ashwin Bihari
2010-08-25 13:51 ` Gadiyar, Anand
2010-08-25 13:58 ` Ashwin Bihari
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4C73BE1C.7080503@compulab.co.il \
--to=grinberg@compulab.co.il \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.