From: linux-arm@overkiz.com (Boris BREZILLON)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH V2] ARM: at91: add kizbox board dt support.
Date: Fri, 20 Apr 2012 14:37:50 +0200 [thread overview]
Message-ID: <4F91589E.5040904@overkiz.com> (raw)
This patch adds support for the kizbox board (based on at91sam9g20 SoC)
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
---
arch/arm/boot/dts/kizbox.dts | 138 ++++++++++++++++++++++++++++++++++++++
arch/arm/mach-at91/Makefile.boot | 1 +
2 files changed, 139 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/boot/dts/kizbox.dts
diff --git a/arch/arm/boot/dts/kizbox.dts b/arch/arm/boot/dts/kizbox.dts
new file mode 100644
index 0000000..c143689
--- /dev/null
+++ b/arch/arm/boot/dts/kizbox.dts
@@ -0,0 +1,138 @@
+/*
+ * kizbox.dts - Device Tree file for Overkiz Kizbox board
+ *
+ * Copyright (C) 2012 Boris BREZILLON <linux-arm@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+/include/ "at91sam9g20.dtsi"
+
+/ {
+
+ model = "Overkiz kizbox";
+ compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "panic=5 ubi.mtd=1 rootfstype=ubifs root=ubi0:root";
+ };
+
+ memory {
+ reg = <0x20000000 0x2000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock at 0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial at fffff200 {
+ status = "okay";
+ };
+
+ usart0: serial at fffb0000 {
+ status = "okay";
+ };
+
+ usart1: serial at fffb4000 {
+ status = "okay";
+ };
+
+ macb0: ethernet at fffc4000 {
+ phy-mode = "mii";
+ status = "okay";
+ };
+
+ };
+
+ nand0: nand at 40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ status = "okay";
+
+ bootloaderkernel at 0 {
+ label = "bootloader-kernel";
+ reg = <0x0 0xc0000>;
+ };
+
+ ubi at c0000 {
+ label = "ubi";
+ reg = <0xc0000 0x7f40000>;
+ };
+
+ };
+
+ usb0: ohci at 00500000 {
+ num-ports = <1>;
+ status = "okay";
+ };
+ };
+
+ i2c at 0 {
+ status = "okay";
+
+ pcf8563 at 51 {
+ /* nxp pcf8563 rtc */
+ compatible = "nxp,pcf8563";
+ reg = <0x51>;
+ };
+
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1g {
+ label = "led1:green";
+ gpios = <&pioB 0 1>;
+ linux,default-trigger = "none";
+ };
+
+ led1r {
+ label = "led1:red";
+ gpios = <&pioB 1 1>;
+ linux,default-trigger = "none";
+ };
+
+ led2g {
+ label = "led2:green";
+ gpios = <&pioB 2 1>;
+ linux,default-trigger = "none";
+ default-state = "on";
+ };
+
+ led2r {
+ label = "led2:red";
+ gpios = <&pioB 3 1>;
+ linux,default-trigger = "none";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset {
+ label = "reset";
+ gpios = <&pioB 30 1>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+
+ mode {
+ label = "mode";
+ gpios = <&pioB 31 1>;
+ linux,code = <0x101>;
+ gpio-key,wakeup;
+ };
+ };
+};
\ No newline at end of file
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
index 0c6e0e9..c36e2df 100644
--- a/arch/arm/mach-at91/Makefile.boot
+++ b/arch/arm/mach-at91/Makefile.boot
@@ -22,6 +22,7 @@ dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9263ek.dtb
# sam9g20
dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g20ek.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += at91sam9g20ek_2mmc.dtb
+dtb-$(CONFIG_MACH_AT91SAM_DT) += kizbox.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += tny_a9g20.dtb
dtb-$(CONFIG_MACH_AT91SAM_DT) += usb_a9g20.dtb
# sam9g45
--
1.7.4.1
next reply other threads:[~2012-04-20 12:37 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-04-20 12:37 Boris BREZILLON [this message]
2012-04-20 12:47 ` [PATCH V2] ARM: at91: add kizbox board dt support Arnd Bergmann
2012-04-20 14:02 ` Jean-Christophe PLAGNIOL-VILLARD
2012-04-20 14:31 ` Boris BREZILLON
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4F91589E.5040904@overkiz.com \
--to=linux-arm@overkiz.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.